Charger USB Anker

I have a 6 s iPhone, recently updated for iOS ver 9.3.4 & since the update, my 'iQ Anker PowerPort 6' http://bit.ly/2aVnXE0 - hub 6-port USB charger charge my iPhone properly.  He was in charge my iPhone perfectly for about 2 months with no problems.  But since the update iOS to 9.3.4, I get a message that says "the cable or accessory is not certified and cannot operate reliably with this iPhone."

What is happening on Apple?  Why would you suddenly cease to support a device that I use my Lightening original iPhone / USB charging cable with and since I bought it?

Plugged my iPhone during the night at the top of the charge and when I woke up this morning... My iPhone has completely discharged battery... Great!  Thanks for that

Fixed!  Turns out be a relief of apple failed / defective USB cable.  He traded against a new and all works fine again

Tags: iPhone

Similar Questions

  • Can I use Yoga 3 Pro to charge USB devices (phone, Tablet, iPad, etc.) when I'm far from an outlet?

    Is Yoga 3 Pro a giant USB battery pack?

    Yes, the Yoga 3 Pro IS a giant USB battery that can charge USB devices is not plugged into an electrical outlet.

    • How does it work?

    The USB port on the right side of Yoga can be configured to be "Always On". Go to the application settings of Lenovo, and powered on, there is a slider to allow him.

    • The 'Always On' USB port stay on when Yoga 3 Pro is unplugged?

    Yes, he does.

    • Always on USB port:

  • Wall charger USB high speed will work with Sansa Fuze?

    Salvation;  I think to buy a double wall on Amazon USB charger new Trent, 10W 5V/2 has two ports high-speed USB AC wall charger (IMP90C) http://www.amazon.com/Trent-Dual-high-speed-charger-IMP90C/dp/B009RXU59C/ref=cm_cr_pr_pb_t

    Characteristics of the product

    • 2.1 wall charger high-speed USB AC 10W amp load.
    • Two USB outputs to charge two devices at the same time.
    • Quickly recharge all your devices USB 5V from a wall outlet
    • Ultra Compact.
    • Overload and short circuit protection

    Product description

    New Trent, wall charger USB double IMP90C
    IMP90C is a secure and high speed charger double USB AC wall charger new Trent. This compact and lightweight charger is compatible with all smart mobile / cell phone on the market with the other compatible similar 5V devices USB rechargeable and a replacement of your OEM charger. Just plug the IMP90C into a wall outlet to US and charge your devices (two devices at the same time that maximum output 2A).

    Compatible with numerous Smartphone/Tablet PC
    -Apple: (4th gen) iPad with Retina, The New iPad screen (3rd generation) / iPad2/iPad/iPhone 4S 5/iPhone / iPhone 4 / iPhone 3Gs / iPod Touch/Classic/Nano
    -Samsung Galaxy Note /Galaxy S2 / phones Galaxy Nexus/all the other Samsung cell
    -HTC Evo Shift 4 G/Incredible feeling/S XL /Thunderbolt / 3D EVO / EVO 4 G / all other Samsung cell phones.
    -Motorola Razr/Atrix / Bionic / the other Motorola Droid X cell, phones X 2 / triumph/All
    -Nokia N900 Lumia / C6 / C3 C7 / E7 / X 6 / N8 / N97 / all the other Motorola cell phones
    -Blackberry Playbook / Tour / Storm 2/curve/Bold/all other cells of Blackberry phones
    -LG Optimus / Quantum / Vortex / all the other cell phones
    -The car charger is also compatible with most tablets 5V which includes the new iPad / iPad 2, Nook color, Nexus 7, etc... and portable game consoles such as Nintendo DSi/3Ds/XL, Sony PSP/PSvita etc. Maybe need a cable or special adapter for some devices: please contact iDealpoint for more details

    Plug
    -Two USB ports
    -Universal 100V - 240V compatible

    My main questions are: would it work with my rocket or it's turn off too much power?  It would hurt my rocket?  This looks like a nice charger.  Any help would be appeciated.  Thank you!

    Thank you;  I just did a live chat with Sansa and they have also confirmed that this charger should work perfectly with the Sansa Fuze.  He received 159 very good reviews on Amazon, all the 4 and 5 stars.  I can't wait to order.    http://www.Amazon.com/Trent-dual-high-speed-charger-IMP90C/DP/B009RXU59C/ref=cm_cr_pr_pb_t

  • Re: NB100-12N - what I need to activate sleep and Charge USB in the BIOS

    Hello

    What I have to go into the BIOS in order to activate this function or it is activated automatically?

    In the case where to enter BIOS why this was resolved in this way?

    Could not simply be available other hassle?

    I really put t know what problems you have with the NB100 and why it of so difficult for you to check if the BIOS contains the USB load option and sleep.

    To my knowledge, the NB100 supports 3 USB ports with Sleep and Charge function.
    But if you want to know if it s on or off then press F2 immediately after that the laptop was turned on to get access to the BIOS Setup.

    Enjoy your little NB100

  • Satellite P100: No external charger USB/Fire-Wire port

    When I plug my ipod into my fire-wire 4 pin port or a USB port on my laptop (satellite P100), it fails to load, even when it is plugged into the mains / power of a/c. I think I've found where I have to go into 'control panel', but need assistance on how to allow my son fire and USB ports give energy and charge my ipod when its connected.

    Any help on this will be greatly appreciated.

    See you soon

    Hello

    The USB ports automatically provide the power. Each USB port provides usually 500mA.
    But please note; the laptop must be running and the device external USB (iPod) must be recognized by the Windows operating system.

    I put t know if the iPod is recognized by drunks, but I read many users have problems with the iPod on the Windows operating system installation. As far as I know that iTunes must be installed if you want to use the iPod.

    Greetings

  • Lack of charges, USB-6211 with linear gauge Mitutoyo (542 series)

    I use a USB-6211 box with a race of 10mm Mitutoyo Linear Gage (542 series, model LGA-110). The Mitutoyo has output similar to an encoder without the time by rev signal quadrature. (B has a phase shift of 90 degrees of A). Signals A and B are airline pilots. I have a k 2 5V to A resistance and another 2K to 5V to B, gives me a minimum of 0.05v and a maximum of 4.75V.

    The problem I encounter is that I seem to be missing certain counts that I can't always zero.

    I found that if I caress the complete range of meter and the return to zero in 20 seconds, I get a value close to 180 meter microphone. If I press the complete range of meter and the return to zero quickly in a second, I get a value close to 800 micrometer.

    If I caress the quick pledge on the compression and rebound more slowly, I find myself with a positive value. I caress the slow pledge on compression and quick on the rebound, I find myself with a negative value.

    As I said before, it seems miss me certain counts. With a pulse of each mic of 4 meters, it means I get only 2500 pulses per 10mm. This means that 10mm per second is only 2500 pulses per second. It seems slow for me, so I don't know what would be the problem.

    Does anyone have ideas for me to try?

    With this type of signal you should not missing any counts.  The time base on the box USB-6211 is 80 Mhz and therefore should have no problem to solve your two pulses per train.  I have a couple of steps that I would like you to try troubleshooting.

    1 to ensure that we plugged the inputs correctly to our DAQ hardware.

    2 ensures that we use both the non-reversed or two signals reversed.  Do NOT mix or 'type' of the signal.

    3 allows you to wire signals A and B in two inputs analog and we will try to read signals to ensure that the sensor is actually be set correctly by the sensor.  Be sure to taste pretty quickly--> 10 the frequency of the pulse train.  If you race through 10 mm in 1 sec--> 2500 pulses per second--> 25 kHz sampling rate.   Allows to check two things.  First we have a good TTL signals, and that we get the right number of charges.  If you reply to this thread plaese attach a screenshot of the present.

    4. we will try different encoder types x 1, x 2, x 4 in the DAQ assistant.  The x 2 and x 4 encoder allows the best sensitivity for small movements (which I'm not sure that it is the source of your proplem but it will be a good thing to check).  Types of encoder are discussed in more detail in the following developer area: quadrature encoder measures: How To?

    Let us know how it shapes to the top.

  • After that charge USB ELPH 100 HS does not illuminate

    Canon Powershot ELPH HS 100 maybe peuvent wall loaded via USB (USB A/Mini B) cable, as some phones? He told me to charge the battery. It doesn't seem to be attached to the PC load. I used a Motorola Droid USB charger and connected to the camera with cable USB A/Mini B I briefly turned on and seen the icon of battery charge on the screen and off. A few hours later, it won't turn. I did the unthinkable and fried it?

    You probably empty the battery. Remove it from the camera and use the charger supplied with the camera. The USB port is not a charge connector.

  • Charger USB sector

    Hi, I was wondering if someone could recommend a USB charger for use in the United Kingdom for the new Sansa Clip + 8 GB that will guarantee to work, I think that one 5V 1 ampere.

    Thanks in advance.

    I went to one of them in the end... http://www.Maplin.co.UK/module.aspx?ModuleNo=227636 it was offered at the time, about half price. It seems to do the job very well

  • 1 GB clip remains on after full charge USB...? Next firmware idea of SanDisk inside...

    Hey all!  :-)

    Got my new Sansa Clip 1 GB plugged into USB and the battery indicator has stopped flashing and shows Full - however, the display is always on showing connected and flashing on the Sandisk logo.

    Why stay on when the player is now loaded?

    If I was going to bed now and let PC to deal with certain things, the player can fuilly charged but keeps cycling through its screens for perhaps up to 8 hours while I'm asleep when there is no need for this too.

    Is this normal?

    Long live the people.

    pinkfloydian

    (PS) Player is on version 16 of REV2

    Thanks to all THE posters.  ;-)

    pinkfloydian

  • Magnetic charge Vs Micro-chargement USB

    Hi all, I currently have the Xperia Z and love it but looking to upgrade to the Z3

    Had a quick google and search the forums, but I can't find the answer.

    With the Z3, which is faster to load by the Micro-USB port, or the magnetic charger port?

    Assuming that they are both on a wall not not a computer and thus to 2.1 has not 1.

    Anyone with a Z3, what is the rough time you also tend to see?

    See you soon!

    From my experience, the two ways load almost at the same rate.

    Some people report slower loading via magnetic connector, but it seems that it was because of the oxidation/dust/scratches on either the magnetic charger port on the phone.

    For my part, I prefer magnetic loading dock, works very well with applications of reverie as timely, so I have an alarm clock virtual beside my bed while you sleep. And of course, do not open the hatch cover to access the micro-USB port.

  • HP Slate 6 do not charge, seems to matter of charge usb port!

    Hello

    On April 27, I bought a HP Slate 6 eme, 2014 is a guarantee.

    I am facing a problem that HP Slate 6 not load and sometimes showing the load but taking 2 hours to 1 unit of the capacity indicator!

    I checked the cable but another device of load with the same cable that is in charge fine.so, it seems, is not cable issue rather charge port connectivity problem.

    Can anyone suggest how can I repair or replace the unit?

    What is the procedure? How to locate a nerby authorized HP repair/replacement Phablet Center South of Chennai, in India.

    It is very urgent that I have all my contacts in there.

    Hello and welcome to the HP support community!

    To contact HP directly, click on this link: http://h22207.www2.hp.com/us-en/contact-hp/

    Outside the United States:
    http://WWW8.HP.com/us/en/contact-HP/WW-phone-assist.html

    WyreNut

  • Error message = the driver failed charging USB\VID_0A5C & PID_5802 & MI_01\7 \Driver\WUDFRd & 95fd152 & 0 & 0001.

    WARNING on 13/10/2011 11:06:08 Kernel - PnP 219 (212)

    Log name: System
    Source: Microsoft-Windows-Kernel-PnP
    Date: 13/10/2011 11:06:08
    Event ID: 219
    Task category: (212)
    Level: WARNING
    Keywords:
    User: SYSTEM
    Computer: Buzz_Murdock-PC
    Description:
    The driver failed to load the device USB\VID_0A5C & PID_5802 & MI_01\7 \Driver\WUDFRd & 95fd152 & 0 & 0001.
    The event XML:
    http://schemas.Microsoft.com/win/2004/08/events/event">
     
       
        219
        0
        3
        212
        0
        0 x 8000000000000000
       
        145356
       
       
        System
        Buzz_Murdock-PC
       
     

     
        44
        USB\VID_0A5C & PID_5802 & MI_01\7 & 95fd152 & 0 & 0001
        3221226341
        14
        \Driver\WUDFRd
        0
     

    I know it's fine... I had the same problem and I stopped the error... I went into services.msc and last 'Manual' under 'Windows Driver Foundation - User - Mode Driver Framework' to 'automatic '.
    This stopped the error in Event Viewer.  It worked for me!

    According to microsoft, the error is benign... It's just a matter of latency.

  • Is the data cable / charging USB for the e280 compatible with the "rocket"?

    What is it really!

    Yes - that's exactly the same cable.

  • Re: Satellite U-500 usb sleep & charge does not

    Hi all

    I have the new satellite U500-PSUME9 which works fine except utility of sleep & charge usb. Sorry if I ask no one qualified to question stupid amn't count
    Any help appreciated. Thanks in advance

    Hello

    1. you must enable usb sleep & fresh in the BIOS
    2 I know, usb sleep & charge is only available for USB ports marked with a small sign of flash.
    3 install/upgrade usb sleep & charge utility from the [page driver Toshiba | http://eu.computers.toshiba-europe.com/innovation/download_drivers_bios.jsp]

  • Charger C - USB plug-and - adapter USB - C will not fully inserted

    We can insert is more completely the plug of charger USB - C OR USB - C adapter (USB - C, USB - A and HDMI).  They stopped short about 1-1, 5 mm.  Food is always delivered, but a very small movement can cause the power disconnected, even if most is still mainly in.  Data connections may be lost in the same way with potentially catastrophic effects.

    Is this a warranty issue?  It's rather disturbing if USB - C plugs/Sockets can fail if relatively fast especially in this case it's an all-Apple above adapters line and computer.

    Yes, usb ports a and c have a very known issue that no one is really writing.

    Is waved from time to time, the connections inside stops working. Also, I tested the adapter, you speak of and it heats more than all of the time and some time. Sometimes if give you him just an hour or two break and then it goes back to normal. His strange indeed.

    Also, I recommend the update to 10.11.3. There has been many corrections of bugs.

Maybe you are looking for