Cisco 1841 ipsec tunnel protocol down after a minute
I have a strange problem where im manages to get a tha cisco ipsec tunnel 1841 to a RV016 linksys/cisco for about a minute and ping/encrypt the packets through the linen for about a minute before it breaks down. I tried different configuration and it all results in the tunnel for a minute then descend to come. I don't know if im hitting a bug and decide to if im doing something wrong.
any help is appreciated paul
RV016 firmware 2.0.18
Cisco 1841: C1841-ADVENTERPRISEK9-M), Version 12.4 (24) T
my config
no default isakmp crypto policy
!
crypto ISAKMP policy 1
BA 3des
md5 hash
preshared authentication
Group 2
lifetime 28800
ISAKMP crypto key address 0.0.0.0 eaton1234 0.0.0.0
!
!
Crypto ipsec transform-set esp-3des esp-sha-hmac ESSTS
transport mode
no default crypto ipsec transform-set
!
Crypto ipsec profile ipsec_profile1
Description in the location main site to site VPN tunnel
game of transformation-ESSTS
PFS group2 Set
!
!
!
!
!
!
!
Tunnel1 interface
Description of the location of the hand
IP unnumbered Serial0/0/0
source of tunnel Serial0/0/0
destination 209.213.x.x tunnel
ipv4 ipsec tunnel mode
tunnel path-mtu-discovery
protection of ipsec profile ipsec_profile1 tunnel
!
a debug output
Apr 24 16:42:07: IPSEC (validate_proposal_request): part #1 the proposal
Apr 24 16:42:07: IPSEC (validate_proposal_request): part #1 of the proposal
(Eng. msg key.) Local INCOMING = 209.213.xx.46, distance = 209.213.xx.164,.
local_proxy = 10.20.86.0/255.255.255.0/0/0 (type = 4),
remote_proxy = 10.0.0.0/255.255.255.0/0/0 (type = 4),
Protocol = ESP, transform = NONE (Tunnel),
lifedur = 0 and 0kb in
SPI = 0 x 0 (0), id_conn = 0, keysize = 0, flags = 0 x 0
Apr 24 16:42:07: mapdb Crypto: proxy_match
ADR SRC: 10.20.86.0
ADR DST: 10.0.0.0
Protocol: 0
SRC port: 0
DST port: 0
Apr 24 16:42:07: IPSEC (key_engine): had an event of the queue with 1 KMI message (s)
Apr 24 16:42:07: mapdb Crypto: proxy_match
ADR SRC: 10.20.86.0
ADR DST: 10.0.0.0
Protocol: 0
SRC port: 0
DST port: 0
Apr 24 16:42:07: IPSEC (policy_db_add_ident): src dest 10.0.0.0, 10.20.86.0, dest_port
0
Apr 24 16:42:07: IPSEC (create_sa): its created.
(his) sa_dest = 209.213.xx.46, sa_proto = 50,.
sa_spi = 0x4CF51011 (1291128849).
sa_trans = sa_conn_id of hmac-sha-esp, esp-3des = 2045
sa_lifetime(k/sec) = (4463729/3600)
Apr 24 16:42:07: IPSEC (create_sa): its created.
(his) sa_dest = 209.213.xx.164, sa_proto = 50,.
sa_spi = 0x1EB77DAF (515341743).
sa_trans = sa_conn_id of hmac-sha-esp, esp-3des = 2046
sa_lifetime(k/sec) = (4463729/3600)
Apr 24 16:42:07: % LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel1, sta changed
you to
Apr 24 16:42:07: IPSEC (key_engine): had an event of the queue with 1 KMI message (s)
Apr 24 16:42:07: IPSEC (key_engine_enable_outbound): rec would notify of ISAKMP
Apr 24 16:42:07: IPSEC (key_engine_enable_outbound): select SA with spinnaker 515341743/50
Apr 24 16:42:07: IPSEC (update_current_outbound_sa): update peer 209.213.xx.164 curre
NT his outgoing to SPI 1EB77DAF
Apr 24 16:42:12: IPSEC (key_engine): request timer shot: count = 1,.
local (identity) = 209.213.xx.46, distance = 209.213.xx.164,
local_proxy = 0.0.0.0/0.0.0.0/0/0 (type = 4),
remote_proxy = 0.0.0.0/0.0.0.0/0/0 (type = 4)
Apr 24 16:42:12: IPSEC (sa_request):,.
(Eng. msg key.) Local OUTGOING = 209.213.xx.46, distance = 209.213.xx.164,.
local_proxy = 0.0.0.0/0.0.0.0/0/0 (type = 4),
remote_proxy = 0.0.0.0/0.0.0.0/0/0 (type = 4),
Protocol = ESP, transform = esp-3des esp-sha-hmac (Tunnel),
lifedur = 3600 s and KB 4608000,
SPI = 0 x 0 (0), id_conn = 0, keysize = 0, flags = 0 x 0
Apr 24 16:42:42: IPSEC (key_engine): request timer shot: count = 2,.
local (identity) = 209.213.xx.46, distance = 209.213.xx.164,
local_proxy = 0.0.0.0/0.0.0.0/0/0 (type = 4),
remote_proxy = 0.0.0.0/0.0.0.0/0/0 (type = 4)
Apr 24 16:42:42: % LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel1, sta changed
you all the downu
All possible debugging has been disabled
I would try to set up a VPN Interface virtual Tunnel on the IOS router base and the value of defined transformation in tunnel mode no transport.
In history, I have had several issues with VPN between a router IOS and the series RV.
Tags: Cisco Security
Similar Questions
-
My new printer HP Officejet Pro 8600 causes my computer shuts down after 5 minutes.
My new printer HP Officejet Pro 8600 causes my computer shuts down after 5 minutes. Is there a way to find out why? Is it because I connected to a USB port rather than wireless and telephone connection.
Original title: computer spit
I called the store where I bought the printer. They suggested that I have download the latest driver
from the HP website. I did it and it seems to have solved the problem.
-
Windows 8 maintenance keeps asking to be executed, then it shuts down after 10 minutes and rehearsals require to be run again, I turnit on and it turns off after 10 minutes .This continues to repeat and it never ends, how do I fix?
Original title: maintenance of windows 8
I suggest that you run the following commands from a command prompt (Admin).
(1) sfc/scannow, when finished and restart
(2) Dism.exe / Online/Cleanup-Image /ScanHealth
(3) Dism.exe/online/Cleanup-Image /RestoreHealth Reboot and try to perform the maintenance, if the problem persists restart sfc/scannow and restart the computer.
Hope this helps and if you need any additional aid station and we will be happy to help you.
The above opinion is mine and mine nothing and does not necessarily reflect that of Microsoft, it's employees, or any other Member of this forum.
"When we try to take anything by itself, we find it hitched to everything else in the universe."-John Muir
If this has answered your message please mark as answer
-
When I stop working on my computer (Dell Inspiron, aio, 2305) I noticed that the screen saver comes on and then it starts to Shut Down without asking to my. All I had to do it before (after the screen saver stopped) was click on any key and the computer was delivered. Now, there is no screen saver, the computer just stops. The log on screen, it says as my SMA, locked. I have to enter my password. This weird isreally. Please help, before things get really out of control,
Hello
(1) have you made changes before the start of this issue?
(2) what is the exact error message/code?
(3) windows operating system you are using?
Try to change the screen saver and check if you face the same problem.
You can check the power setting and set it accordingly.
See the link below:
For windows 7
Power management
http://Windows.Microsoft.com/is-is/Windows7/products/features/power-managementFor windows XP:
Configure Windows XP power management
http://Windows.Microsoft.com/en-us/Windows-XP/help/Setup/configure-power-managementSee also:
What happened in standby and hibernation mode?
http://Windows.Microsoft.com/en-us/Windows-Vista/what-happened-to-standby-and-HibernateI hope this helps. -
IPSec VPN auto-timeout after 60 Minutes
Dear all,
I am facing a problem. When my clients are connecting remote VPN IPSec an hour it automatically disconnects the connection. Users need to be re - authenticate. I also changed the timekeepers of the IPSec Security Association and timer ISAKMP, but still the same problem persists.
According to my findings my user authentication becomes Cisco ACS/RADIUS server, which is running on the default settings and the policy is enforced by Cisco ACS. I have a suggestion how can I set the timer and to address this problem.
Any suggestion?
Waiting for your RESPONSE.
Concerning
Yasser
Yasir,
What version of ACS you run and very probably the attribute "session timeout" is probably sent, you can extend this attribute or remove it on the status of the authorization.
Let me know what version of ACS you run and I can walk you through it...
Thank you
Tarik Admani
* Please note the useful messages *. -
SP6100 shuts down after 20 minutes then OK
SP6100 works for 20 minutes when put in operation then stops. Remove the power cord, removal and replacement of battery and replacement cord the laptop restarts and is good for the rest of the day. Any ideas? Have you tried another battery and same scenario.
Hello
It's not easy to say why this problem occurs. In my view, that the cooling module can t working properly at the time and the temperature rises up to the critical limit. Then the operating system stops to avoid the problem of overheating.
It s seems that after I removed and connect the battery fan works fine and the temperature remains stable.It s my own suggestion but unfortunately I don t know why this happens.
I think you should contact Toshiba service. -
Satellite L555-10N screen will not shut down after 10 minutes of non-use
Hello
I recently acquired a laptop Satellite L555-10N, which so far has proved to be a good choice.
I have a little problem, however:In the preferences of my energy, I put the time during which the screen should turn off, 10 minutes, if the laptop is not in use.
Although this worked well for the last few days and weeks, the display now will be not closed at all.
I did not change the BIOS or driver or whatever.I remember to change some preferences in the configuration ecoUtility to enable.
At that time, I received a message that preferences should be modified to enable the functionality and I agreed.I could not notice any changes have been made, but from there, the screen off more.
I would appreciate your help!Thank you!
Hello
What operating system you are using?
For Vista and Windows 7, I founded a good article on Windows power management settings:
http://APS2.toshiba-tro.de/KB0/HTD84026Q0000R01.htmIn addition, you can change the settings for each profile. This means that you should choose turn it off the display function for this power profile that you use or all profiles, if I used all of them.
Check this box!
-
The screen brightness down after 2 minutes
Still can not find a way to delay auto shutdown Pro.
My iPad pro won't stay on for more than two. Guest without touching the screen
Sorry, the question should read... Will not stay more than two minutes without touching the screen. Screen fades away first, then black out (standby),
By touching the screen he brings complete operation if it is not passed to sleep.
Is this a deliberate battery save installation with no way to remove this action or to set the time of appeasement, etc.. ?
-
We have 3 IPSec tunnel set up between the cisco 1760 router and PIX 515e. IPSec tunnel is down by intermittent & son come only after compensation isakmp crypto & clear crypto its next to the router.
do we need to configure something else in router and end of pix so that tunnels are still in Active state (QM_IDLE).
Looks like the PIX loses its connection and the router is unable to say that the PIX has dropped.
Try the isakmp keepalive on both devices configuration but also check network links extended features.
See you soon,.
Paul.
-
Connection Internet drops after 15 minutes 7 windows
Original title: network goes down after 15 minutes
15 minutes after the start, I lose my connection to the internet. Another computer on my network still end. I tried restoring but it won't work. At the time of 95 to XP I would reinstall over the existing o/s & everything would be fine. Can I do this with Windows 7Pro? I tried the network troubleshooting. No go. Any advice?
TIA
Hi Richard,
You are welcome. Glad to know that your problem is solved.
Answer to your other question is 'yes '. You can re - install "Operating System" using a DVD on the system of 'exploitation' If you computer performance is slow or if you want to do a repair. We call this process 'in place upgrade'. For more information, see the article below.
How to perform an upgrade on the spot on Windows;
http://support.Microsoft.com/kb/2255099
Response from us, then we can help you further.
-
Cisco's ASA IPsec tunnel disconnects after a while
Hi all
I've set up an IPsec tunnel between sonicwall pro road and cisco ASA 5510. The well established tunnel and two subnets can access each other.
I then added a static route to a public ip address on the sonicwall ipsec policy, so that all traffic to this ip address will go through the IPsec tunnel. It also works very well.
But the problem is aftre tunnel Ipsec sometimes breaks down, and then I need to renegotiate the ipsec on sonicwall to restore the tunnel.
This happens twice a day. I'm whther fear that this behavior is because of problems with config. I'm pasting my ASA running Setup here. Plese give some advice.
SonicWALL publicip 1.1.1.2 192.168.10.0 subnet
Cisco ASA publicip 1.1.1.1 subnet 192.168.5.0
ciscoasa # sh run
: Saved
:
ASA Version 8.2 (1)
!
ciscoasa hostname
domain default.domain.invalid
activate 8Ry2YjIyt7RRXU24 encrypted password
2KFQnbNIdI.2KYOU encrypted passwd
names of
!
interface Ethernet0/0
Speed 100
full duplex
nameif outside
security-level 0
IP 1.1.1.1 255.255.255.248
!
interface Ethernet0/1
nameif inside
security-level 100
192.168.5.1 IP address 255.255.255.0
!
interface Ethernet0/2
Shutdown
No nameif
no level of security
no ip address
!
interface Ethernet0/3
Shutdown
No nameif
no level of security
no ip address
!
interface Management0/0
nameif management
security-level 100
IP 192.168.1.1 255.255.255.0
management only
!
passive FTP mode
DNS domain-lookup outside
DNS lookup field inside
DNS server-group DefaultDNS
Server name 66.28.0.45
Server name 66.28.0.61
domain default.domain.invalid
permit same-security-traffic inter-interface
permit same-security-traffic intra-interface
object-group service rdp tcp
EQ port 3389 object
object-group service tcp OpenVPN
port-object eq 1194
access list outside extended permit icmp any any echo response
access list outside extended permit tcp any host # eq pptp
outside allowed extended access will list any host #.
list of extended outside access permit udp any any eq 1701
extended outdoor access allowed icmp a whole list
access list outside extended permit tcp any host # eq ftp
access list outside extended permit tcp any host # eq ssh
list of extended outside access permit tcp any host # object - group rdp
turn off journal
access list outside extended permit tcp any host 1.1.1.1 object - group Open
VPN
access-list sheep extended ip 192.168.5.0 allow 255.255.255.0 192.168.5.0 255
. 255.255.0
access-list sheep extended ip 192.168.5.0 allow 255.255.255.0 192.168.10.0 255
. 255.255.0
L2L 192.168.5.0 ip extended access-list allow 255.255.255.0 192.168.10.0 255.2
55.255.0
pager lines 24
Enable logging
asdm of logging of information
Outside 1500 MTU
Within 1500 MTU
management of MTU 1500
IP local pool ippool 192.168.5.131 - 192.168.5.151 mask 255.255.255.0
IP local pool l2tppool 192.168.5.155 - 192.168.5.200 mask 255.255.255.0
ICMP unreachable rate-limit 1 burst-size 1
ASDM image disk0: / asdm - 621.bin
don't allow no asdm history
ARP timeout 14400
Global 1 interface (outside)
NAT (outside) 1 192.168.10.0 255.255.255.0
NAT (outside) 1 192.168.5.0 255.255.255.0
NAT (inside) 0 access-list sheep
NAT (inside) 1 192.168.5.0 255.255.255.0
outside access-group in external interface
Route outside 0.0.0.0 0.0.0.0 38.106.51.121 1
Timeout xlate 03:00
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
dynamic-access-policy-registration DfltAccessPolicy
the ssh LOCAL console AAA authentication
AAA authentication LOCAL telnet console
Enable http server
http 192.168.1.0 255.255.255.0 management
http 192.168.5.0 255.255.255.0 inside
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown cold start
Crypto ipsec transform-set esp-3des esp-sha-hmac RIGHT
life crypto ipsec security association seconds 28800
Crypto ipsec kilobytes of life - safety 4608000 association
Crypto-map dynamic dynmap 5 the value reverse-road
Crypto easyvpn dynamic-map 10 transform-set RIGHT
Crypto-map dynamic easyvpn 10 reverse-drive value
card crypto mymap 10 correspondence address l2l
card crypto mymap 10 set peer 1.1.1.2
card crypto mymap 10 transform-set RIGHT
map mymap 30000-isakmp ipsec crypto dynamic easyvpn
mymap outside crypto map interface
crypto isakmp identity address
crypto ISAKMP allow outside
crypto ISAKMP policy 10
preshared authentication
3des encryption
md5 hash
Group 2
life 86400
crypto ISAKMP policy 20
preshared authentication
3des encryption
sha hash
Group 2
life 86400
crypto ISAKMP policy 65535
preshared authentication
3des encryption
sha hash
Group 2
life 86400
Crypto isakmp nat-traversal 3600
Telnet 192.168.5.0 255.255.255.0 inside
Telnet timeout 5
SSH 0.0.0.0 0.0.0.0 outdoors
SSH timeout 5
Console timeout 0
Hello to tunnel L2TP 10
management of 192.168.1.2 - dhcpd address 192.168.1.254
enable dhcpd management
!
a basic threat threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
WebVPN
internal DefaultRAGroup group strategy
attributes of Group Policy DefaultRAGroup
value of 66.28.0.45 DNS server 66.28.0.61
Protocol-tunnel-VPN IPSec l2tp ipsec
field default value cisco.com
attributes of Group Policy DfltGrpPolicy
internal band easyvpn strategy
attributes of the strategy of band easyvpn
value of 66.28.0.45 DNS server 66.28.0.61
Protocol-tunnel-VPN IPSec
enable IPSec-udp
Split-tunnel-policy tunnelall
the address value ippool pools
VPN-group-policy DefaultRAGroup
attributes global-tunnel-group DefaultRAGroup
address l2tppool pool
Group Policy - by default-DefaultRAGroup
IPSec-attributes tunnel-group DefaultRAGroup
pre-shared-key *.
tunnel-group DefaultRAGroup ppp-attributes
No chap authentication
ms-chap-v2 authentication
tunnel-group 1.1.1.2 type ipsec-l2l
1.1.1.2 tunnel-group ipsec-attributes
pre-shared-key *.
tunnel-group easyvpn type remote access
tunnel-group easyvpn General attributes
Group Policy - by default-easyvpn
easyvpn group tunnel ipsec-attributes
pre-shared-key *.
!
class-map inspection_default
match default-inspection-traffic
!
!
type of policy-card inspect dns preset_dns_map
parameters
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the preset_dns_map dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
inspect the rsh
inspect esmtp
inspect sqlnet
inspect the skinny
inspect sunrpc
inspect xdmcp
inspect the netbios
inspect the tftp
inspect the pptp
!
global service-policy global_policy
context of prompt hostname
Cryptochecksum:5542615c178d2803f764c9b8f104732b
: endI guess you have typo in the configuration of the ASA?
L2L 192.168.5.0 ip extended access-list allow 255.255.255.0 192.168.10.0 255.255.255.0
list access extended extended permitted host ip voip pubic ip 192.168.10.0 255.255.255.0Can you confirm that you have configured instead the following:
access-list l2l extended permitted host ip voip pubic ip 192.168.10.0 255.255.255.0
Moreover, even if the crypto map tag says easyvpn; peer address is correct to point 1.1.1.2
In addition, don't know why you have the following configuration (but if it is not necessary I suggest to be removed and 'clear xlate' after the withdrawal):
NAT (outside) 1 192.168.10.0 255.255.255.0
Finally, pls turn off keepalive to SonicWall.
If the foregoing still don't resolve the issue, can you try to remove the card dynamic encryption of the ASA (no map mymap 30000-isakmp ipsec crypto dynamic easyvpn), release the tunnel and try to open the tunnel between the ASA and SonicWall and take the exit of "show the isa cry his ' and ' show cry ipsec his» I'm curious to see why he is always referred to the easyvpn crypto map. When you remove the dynamic encryption card, dynamic vpn lan-to-lan of remote access client does not work.
-
Windows Error VPNC3005 "unauthorized tunneling protocol" L2TP/IPSec
I'm trying to implement a vpn L2TP/IPSec to a concentrator 3005. Everything seems to work (phase 1 completed, PHASE2 full, updated tunnel, the session began and the user is authenticated with the RADIUS) but then the tunnel fell with the message "unauthorized tunneling protocol. What causes this message?
At one point the tunnel remained upward and running, but later I tried again and it failed. I don't remember changing anything in the config right.
I read somewhere that I should turn on "L2TP over IPSEC" in the group but this disables the IPSEC option and it seems to me that I need IPSec for Cisco vpn clients that need to connect.
Any suggestions?
Change the base group to allow l2tp/ipsec; Check if l2tp is enabled at the global level.
-
1841 can route between tunnel GRE and IPSEC tunnel?
Hello everyone!
See the image below.
Main office (10.0.1.0/24 LAN) and branch (10.0.2.0/24 LAN) are connected through the GRE tunnel.
The third office (10.0.3.0/24) is attached to the second branch via IPSEC.
Is there the way to establish the connection between the third and the main office through cisco 1841?
Is it possible to perform routing, perhaps with NAT?
In fact we need connection with a single server in the main office.
Thank you
Hello
It is possible to build this configuration.
the IPSEC connection between 10.0.3.x and 10.0.2.x should also encapsulate the traffic to main office.
Steps to follow:
Central office, to shift traffic to 10.0.3.x above the GRE tunnel.
The second part, add the 10.0.3.x - 10.0.1.x selection of traffic to the ACL IPSEC with the third
The third part, add the 10.0.3.x - 10.0.1.x selection of traffic to the ACL IPSEC with the second pane.
Please rate if this helped.
Kind regards
Daniel
-
Tunnel down after a certain period of time
Hi all
I configured 2 837 Cisco using SDM,
VPN type: Site to another, with sharing of key.
Both sides with ADSL and fixed IP (real ip).
I got to the top with "TEST TUNNEL" but the VPN does not up if I stop no matter what router.
After some time the tunnel breaks down and I don't know how to keep the tunnel up. I tried keepalive settings with no good news.
Any suggestion?
The tunnel should appear automatically when traffic is sent through it.
Otherwise, take a look at this tool to generate a site configs:
-
Cisco 1841 how vpn tunnels? default 100vpn?
Hi everyone, I have read the previous posts and I read that the cisco 1841 can manage up to 100 default VPN tunnels.
1. is this true? (I enclose my worm of show)
2. this version of IOS support SSL VPN tunnels as well?
SH ver
Cisco IOS Software, 1841 (C1841-ADVSECURITYK9-M), Version 12.4 (3i), VERSION of the SOFTWARE (fc2)
Technical support: http://www.cisco.com/techsupport
Copyright (c) 1986-2007 by Cisco Systems, Inc.
Updated Thursday 28 November 07 18:48 by stshenROM: System Bootstrap, Version 12.4 (13r) T, RELEASE SOFTWARE (fc1)
Uptime SPAREROUTER is 7 minutes
System to regain the power ROM
System image file is "flash: c1841-advsecurityk9 - mz.124 - 3i.bin".... Output omitted
Cisco 1841 (revision 7.0) with 234496 K/K 27648 bytes of memory.
Card processor ID FTX1151Y0BQ
2 FastEthernet interfaces
1 module of virtual private network (VPN)
Configuration of DRAM is 64 bits wide with disabled parity.
191K bytes of NVRAM memory.
62720K bytes of ATA CompactFlash (read/write)Configuration register is 0 x 2102
SPAREROUTER #.
Thank you
Randall
Hello
I guess that means that the total number of vpn ipsec tunnels taken in charge by the router of SSL VPN AIM is 800.
If you want only a SSL VPN without the AIM module can it be based on the license.
Kind regards
Anisha
P.S.: Please mark this thread as answered if you feel that your query is resolved. Note the useful messages.
Maybe you are looking for
-
A password has been stored for a site and I would like to remove it
When I click on stored Security Options past the list is empty, and neither the site nor the password stored for appear.In view of this, any advice on how I can remove the password would be greatly appreciated. Re-install Firefox would do the trick?C
-
15 - ay013nr: how to tell which USB 3.0 port when they are not blue?
How am I supposed to say which USB port is my port 3.0? I thought they were supposed to be blue? Laptop model # 15 - ay013nr Thank you
-
Is my Skype works correctly? -All contacts.
Hi, so I don't know if my Skype works properly or not. All my contacts are there, when I connect first, some are indicated offline and online and then they are all far. However, when I log in the beta version of Skype on the Web, they are both shown
-
HP Pavilion 15-e091eo Ram and ssd upgrade.
Hello! My computer is HP Pavilion e091eo 15 and I expected to make it even faster. I found these two products on amazon and I was wondering if they are not suitable for my computer. RAM: http://www.amazon.com/gp/product/B00CQ35GYE SSD: http://www.ama
-
Connect Electrocardiograma CONTEC
Hola soy nuevo in el foro y estoy aprendiendo a usar labview Quiero UN electrocardiografo marca CONTEC ECG300G http://www.contecmed.com/index.php?page=shop.product_details&flypage=flypage.tpl&product_id=83&categ... connect USB esto para poder tener l