Cisco 2960 and uplinks AIR-AP1041N

Guys,

what I'm doing wrong here?  I need to enable trunking to pass on several VLANs to my AP, but when I put the 2960 as trunk mode I lose connectivity to the AP.

All will help it useful!

Course AP Interface congfigs:

interface GigabitEthernet0.210
210 native encapsulation dot1Q
no ip route cache
Bridge-Group 1
No source of bridge-Group 1-learning
Bridge-Group 1 covering-disabled people
end

+++++++++++++++++++++++++++

210 native encapsulation dot1Q
no ip route cache
Bridge-Group 1
Bridge-group subscriber-loop-control 1
Bridge-Group 1 block-unknown-source
No source of bridge-Group 1-learning
unicast bridge-Group 1-floods
Bridge-Group 1 covering-disabled people
end

2960 new switch port config (lost connectivity to AP unless I put back to access the mode vlan210 why?)

GigabitEthernet1/0/1 interface
AP USTCRLW001 description
switchport mode trunk
SRR-queue bandwidth share 1 30 35 5
priority queue
MLS qos trust cos
Auto qos trust
end

Add this on swicthport where AP is connected:

GigabitEthernet1/0/1 interface
AP USTCRLW001 description

Switchport tunk native valn 210
switchport mode trunk
SRR-queue bandwidth share 1 30 35 5
priority queue
MLS qos trust cos
Auto qos trust
end

Concerning

Remember messages useful rates

Tags: Cisco Wireless

Similar Questions

  • Gateway to Comcast Business class SMCD3G-CCR and Cisco 2960 G switch

    Hello

    I'm looking to upgrade my silent switches to a Cisco 2960 switch.  I wanted to check and make sure that this configuration would be funded.

    I need to configure the 4 VLANS on Cisco 2960 switch, 1 for the vmotion traffic, which would have no internet access, one for management traffic that does not have internet access, for standard server traffic and traffic vmserver, who should access to the internet.

    The Cisco switch working with gateway SMCD3G-CCR ok, or do I need another router for this?  If yes why?

    I don't know if this is the right forum but I know that Cisco linksys bough, so I hope someone can point me in the right direction.

    Thank you

    Hello.

    These products are processed by the Cisco Small Business Support Community.

    * If my post answered your question, please mark it as "acceptable Solution".

    Thank you!

  • Switch Cisco 2960/3560 = > recovery password and default settings with the button Mode

    Hi Experts,

    I have some confusion with the button Mode with cisco 2960/3560 switches.

    I read on many forums and articles, but where things are not clear.

    a place given 3 seconds and somewhere is given 7 or 10 seconds.

    Qus1), what is the exact time to press/hold Mode button to perform two following tasks:

    A. password recovery (according to my knowledge 3 sec) good or bad?

    Configuration of the switch (start + run) would be safe

    After the recovery of password? Yes or no

    B. factory default (according to my knowledge 10 dry) good or bad?

    I'm afraid, because if I press mode button more than 3 seconds, then

    It will delete any configuration of cisco switch. Yes or no

    Qus2) I want to recover the catalyst 2960/3560 switch password without

    Start/run configuration to lose. That is my main concern.

    Please tell me how to do this, what will be the time keeping Mode buttom

    in a few seconds?

    Qus3) which means this line

    "If the password recovery mechanism is disabled in switch

    then you will lose all the config.

    This sentence has been given on this forum url

    https://supportforums.Cisco.com/thread/140848

    KS

    Attach a terminal or PC with terminal emulation (for example, Hyper Terminal) port console switch.

    Use the following terminal settings:

    • Bits per second (baud): 9600

    • Data bits: 8

    • Parity: None

    • Stop bits: 1

    • Flow control: Xon/Xoff

    Note: For more information on the wiring and connection of a terminal to the console port, refer to connecting a Terminal to the Console Port of Catalyst switches.

    Unplug the power cable.

    The power switch and take it to the switch: command prompt:

    2900XL, 3500XL, 2940, 2950, 2960, 2970, 3550, 3560, and 3750 switches of the series, to do this:

    Press and hold the mode button located on the left side of the façade, while you reconnect the power cable from the switch.

    2960, 2970 Release the Mode button when the SYSTEM LED flashes orange and then turns green. When you release the Mode button, the SYSTEM LED flashes green.
    3560, 3750 Release the Mode button after about 15 seconds when the SYSTEM LED turns green. When you release the Mode button, the SYSTEM LED flashes green.

    The system was interrupted before the flash at the end file system initialization

    loading the operating system software:

    flash_init

    load_helper

    boot

    switch:

    Run the flash_init command.

    switch: flash_init Initializing Flash... flashfs[0]: 143 files, 4 directories flashfs[0]: 0 orphaned files, 0 orphaned directories flashfs[0]: Total bytes: 3612672 flashfs[0]: Bytes used: 2729472 flashfs[0]: Bytes available: 883200 flashfs[0]: flashfs fsck took 86 seconds ....done Initializing Flash. Boot Sector Filesystem (bs:) installed, fsid: 3 Parameter Block Filesystem (pb:) installed, fsid: 4 switch: !--- This output is from a 2900XL switch. Output from !--- other switches will vary slightly.

    Run the load_helper command.

    switch: load_helper switch:

    Question the dir flash: command.

    Note: Be sure to type a colon ":" after the dir flash.

    Appears in the file system of the switch:

    switch: dir flash: Directory of flash:/ 2    -rwx  1803357                  c3500xl-c3h2s-mz.120-5.WC7.bin !--- This is the current version of software. 4    -rwx  1131                     config.text !--- This is the configuration file. 5    -rwx  109                      info 6    -rwx  389                      env_vars 7    drwx  640                      html 18   -rwx  109                      info.ver 403968 bytes available (3208704 bytes used) switch: !--- This output is from a 3500XL switch. Output from !--- other switches will vary slightly.

    Type rename flash: flash: config.old config.text to rename the configuration file.

    switch: rename flash:config.text flash:config.old switch: !--- The config.text file contains the password !--- definition.

    Issue the boot command to boot the system.

    switch: boot Loading "flash:c3500xl-c3h2s-mz.120-5.WC7.bin"...############################### ################################################################################ ###################################################################### File "flash:c3500xl-c3h2s-mz.120-5.WC7.bin" uncompressed and installed, entry po int: 0x3000 executing... !--- Output suppressed. !--- This output is from a 3500XL switch. Output from other switches !--- will vary slightly.

    Enter "n" at the prompt to abort the initial configuration dialog box.

    --- System Configuration Dialog --- At any point you may enter a question mark '?' for help. Use ctrl-c to abort configuration dialog at any prompt. Default settings are in square brackets '[]'. Continue with configuration dialog? [yes/no]: n !--- Type "n" for no. Press RETURN to get started. !--- Press Return or Enter. Switch> !--- The Switch> prompt is displayed.

    At the switch prompt, type en to enter a mode.

    Switch>en Switch#

    Password recovery

    Type rename flash: config.old flash: config.text to rename the configuration file with its original name.

    Switch#rename flash:config.old flash:config.text Destination filename [config.text] !--- Press Return or Enter. Switch#

    Copy the configuration file in the memory.

    Switch#copy flash:config.text system:running-config Destination filename [running-config]? !--- Press Return or Enter. 1131 bytes copied in 0.760 secs Sw1#

    The configuration file is now reloaded.

    Replace the current passwords that you do not know. Choose a password with at least one capital letter, one number and one special character.

    Note: Replace passwords that are required. You must crush not all passwords listed.

    Sw1# conf t !--- To overwrite existing secret password Sw1(config)#enable secret !--- To overwrite existing enable password Sw1(config)#enable password !--- To overwrite existing vty password Sw1(config)#line vty 0 15 Sw1(config-line)#password Sw1(config-line)#login !--- To overwrite existing console password Sw1(config-line)#line con 0 Sw1(config-line)#password 

    Write the running configuration in the configuration file with the write memory command.

    Sw1#write memory Building configuration... [OK] Sw1#

    For factory reset:

    do not give under the control of factory reset

    Switch#copy flash:config.text system:running-config

    can I copy the running configuration to Flash

    Switch flash running-config #copy:

    Destination file name [running-config]?

    Building configuration...

    [OK]

    Switch #copy running-config startup-config

    Name of destination file [startup-config]?

    Building configuration...

    [OK]

    Review the link for more information below

    http://www.Cisco.com/en/us/products/hw/switches/ps628/products_password_recovery09186a0080094184.shtml

    Please note the useful messages.

    Concerning
    Vesta
    "Everybody is genius." But if you judge a fish by its ability to climb on a tree, he will live his entire life, believing that this is stupid. "

  • AIR-LAP1041N > AIR-AP1041N

    Hello

    I have a LAP1041N AIR. I understand that it is possible to turn this device into the AIR-AP1041N Cisco by downloading new software in the access point.

    Can someone help me by downloading the correct software and give a guide to do.

    Cisco want to sell a smartnet contract, but we didn't need...

    Many thanks in advance, Arend

    Hello

    Yes, we can convert the LWAPP AP to AP autonomous... Here is the link to download the picture...

    Download this image c1140-k9w7 - tar.124 - 25d.JA.tar

    http://www.Cisco.com/Cisco/software/release.html?mdfid=283445229&flowid=17961&softwareid=280805680&release=12.4.25D-ja&rellifecycle=Ed&relind=available&RelType=all

    And please follow the instructions of the below document iOS LWAPP

    https://supportforums.Cisco.com/docs/doc-14960

    Let me know if this answered your question!

    Concerning

    Surendra

  • LAPAC1750PRO & Cisco 2960-S - LACP issues Switch

    Hello community,

    I currently have a layer 2 Cisco 2960-S switch. It has 48 port Gigabit Ethernet ports and 4 SFP ports. I have Setup 3 VLAN on the switch VLAN 10, 11, 255. VLAN 10 is for my home equipment, VLAN 11 for my Audio/video/server equipment and VLAN255 is my network of comments. It's all behind a normal router from D-Link 4 port every day. All correctly connected working processes.

    I have the LAPAC1750PRO access point, I went ahead and ran 2 Cat6 cables so I could take advantage of the link aggregation 802.3d of the Access Point. I configured the passage from what I can tell properly. The problem is that when I turn on the two links AP causes beating port and stop passing traffic. If I disable the second link (leaving the active primary link) everything is stable. Speed is decent on my laptop, and from my iPad, it's fantastic.

    Does anyone have experience using the Protocol LACP (link Aggreagtion 802.3d) with this Access Point? I really want to use this so I can get 2 Gbps throughput of this device to my other devices.

    I'll be happy to post my Cisco Configuration so if someone is paid enough in that as well.

    Thank you

    Jason

    Senior Network Engineer

    OK - I thought about it. He was not at all a problem with the switch or my setup. This is the problem...

    Here's the question – and how I fixed it.

    1 cisco switch - Configuration:

    !

    GigabitEthernet1/0/1 interface
    switchport access vlan 10
    switchport mode access
    spanning tree portfast
    channel-group mode 1 on

    !

    interface GigabitEthernet1/0/2
    switchport access vlan 10
    switchport mode access
    spanning tree portfast
    channel-group mode 1 on

    That's right - this force LACP on the unit and do not have to worry about negotiating/connections protocols.

    2. access point - if it is already configured - factory reset the unit. LACP must be enabled during active keybord with DHCP boot. After that you can configure it as you want.

    What I had to do so was by default the access point and let it be starting with LACP rebuild - I wonder if this is due to something in the firmware that, once the NIC is configured, they become hardcoded and do not change to different settings?

    Whatever it is - this problem is solved.

  • UCS < 1.4.2b >, N1K and uplink

    Hi all

    I have a UCS (cluster) connected in vPC mode to a Nexus 7010.

    UCS 4.1U1 VMware ESXi, N1K with EHM PC blade-based UCS NIC is 71KR.

    Question is what happens if the two uplink of interconnection fails? I mean maybe cut fibres or stuff like that. N1K channel will be still two active link?

    Maybe the redundancy is performed by re arping for finding a mac (i've got UCS in switch mode) address, but I'm not sure. I saw a feature in the new version for a link status tracking rising full failure handling system (how?).

    last question about redundancy... what happens if a UCS IOM resets? I have some traffic disruption?

    TNX

    Dan

    Dan,

    Just to be clear, check the following:

    -UCS in switch mode

    -Adapters M71KR

    -N1k using Mac-pinning (I guess)

    -Connectivity upstream of each FI is a VPC to a pair of N7Ks.

    In this case, the N1K has no visibility of uplinks UCS.  See all your hosts VEM are two uplinks for each host (a session each fabric interconnect.)  If one of the two uplinks fails on interconnection, traffic will be the uplink remaining on this FI re-hairpin.  If the TWO uplinks on a financial institution fail, then UCS will be down (called the link at the bottom) server links and traffic should be routed through the MEC is another uplink will the other.  You can change this behavior to follow links to Server (for local switching only) but the default action of UCSM's close links to corresponding server if there are no links available on a financial institution.   Make sense?

    Now, in the last version of N1K here (1.4) is a new feature called followed by the State of the network (NST) for use with VPC - HM (such as Mac pinning).  This feature will allow to test the connectivity of a VLAN sends a probe packet and expect to get fired on another group of liaison rising/sup.   If you have a network VLAN which SHOULD be identified, you can follow with TSN.  If the network becomes unavailable, you can choose to close the uplink and re - route traffic to an another uplink.  This is useful to detect failures beyond the first jump (which would be the interconnections) as a failure somewhere in your N7K level or beyond.

    Setup Guide: http://www.cisco.com/en/US/partner/docs/switches/datacenter/nexus1000/sw/4_2_1_s_v_1_4/interface/configuration/guide/n1000v_if_5portchannel.html#wp1284321

    White paper: https://communities.Cisco.com/docs/doc-20657

    Order code: http://www.cisco.com/en/US/docs/switches/datacenter/nexus1000/sw/4_2_1_s_v_1_4/command/reference/n1000v_cmds_t.html#wp1295608

    For your last question about a failure/reset of the IOM, the cards corresponding to each blade will lose connectivity.  This is redundancy at the host level comes into play to reroute traffic.  In the case of your hosts N1K VEM, they would simply be re - route traffic on the access road to functional IOM of the chassis.

    Another point to consider is the M71 and M81 adapters support Fabric Failover.  He is tilting at the adapter level if there is a failure with any device between the adapter and uplink (like the IOM or FI).  Fabric failover is a configurable option adapter which re - will route traffic in Menlo ASIC adapters to the fabric in the 'other', such that the host will NOT see one of the two ports down.  Without switch fabric, a failure of a MOI or FI consider the adapter and this port would descend.  FF only adds a level of redundancy in the adapter without having to rely on any OS host grouping/failover.  M51KR, M61 KR and M72KR adapters do NOT support this feature.

    Kind regards

    Robert

  • 2960S and REP

    Hello

    I recently bought a number of switches Cisco 2960 S-24TD-L and would like to know if they support REP (resilient Ethernet Protocol). I've implemented a development space and have telnet would be one of the 2960 to attempt to configure a Port on board, but I keep getting the 'invalid command' response when the representative of Word is used.

    The current software is 12.2 (55) SE7.

    Any help would be appreciated.

    See you soon

    Tom

    Hello, Tom.

    2960S does not support it.

    By my understanding, this is a feature of the ISP, supported on IE3000, ME and other IOSs "ISP feature.

  • Cisco Catalyst 4503-> Cisco 3560 L3-> Cisco 2960 L2-> Cisco SMB switch

    Hi Experts,

    I am trying to add a Cisco SMB SF300 - 24 Switch to an infrastructure that has only the Cisco Catalyst switches

    The base layer is Cisco Cataylst 4503. Distribution is Cisco Catalyst 3560 and Cisco 2960 switches access layer.

    There are about 30 VLAN present in the infrastructure that is announced to all switches using VTP. Inter VLAN routing takes place at basic switches

    by creating the Interface VLAN for each VLAN of L2.

    1. the new 150 VLAN must be created on the new Cisco SMB switch. If I create a corresponding interface 150 VLAN on core switches, it will forward the other VLANs traffic just as he is currently working for Cisco 2960 Catayst switches?

    2. While they inspected, I could see that the DERIVATIVE is not supported on the Cisco SMB switches and I would need to go GVRP if I need to make advertising information to other switches VLAN. But since GVRP is only supported on CatOS and there is no inter operability between GVRP and DERIVED, I would need to manually create the VLAN on the new switch. Is this correct?

    Help, please!

    Thank you very much

    ANUP

    Good afternoon Anup Sasikumar

    Please use our forum

    My name is Johnnatan I am part of the community of support to small businesses, I saw your post and I understand that you want to configure VTP and GVRP.

    I'm afraid you will have to configure it manually each Vlan in each device CatOS GVRP, in order to keep their databases vlan in sync. As you say, VTP is support it not in CatOS

    You can try to connect the two protocols, but I encourage you do not follow this procedure.

    On your question about intervlan routing, if you create a corresponding interface 150 VLANS on switches to base it is routed, if your configuration is correct (port access, ports of junction, intervlan etc..)

    I hope that you will find this answer useful, if it was satisfactory to you, please indicate the question as answer.

    Please evaluate the useful messages.

    Greetings,

    Johnnatan Rodriguez Miranda.

    Support of Cisco network engineer

  • iCloud keeps asking for password on iPad, iPhone, and Macbook Air

    I have a Mini iPad, iPhone 6 and Macbook Air, which is still invited to enter my password to iCloud.  All have BONES perfectly up-to-date.  On the iPad, I did a full erase and restore, nothing helps.  Since then, I also signed on iCloud and signed in on the iPad, I have not tried who still on other devices.  My iCloud username is an @me.com format, so I made sure that all newspapers in places (FaceTime, iTunes Store, messaging, etc., use this journal, even if I have a @icloud.com email too.)  I disabled 2 authentication and password specific to the Messages and FaceTime App.

    It seems to have something to do with email in particular.  On the Macbook Air from Apple email program, I get a message on the main window connection failed, and then the iCloud account is set offline.  I have to retype the iCloud password and/or exit and restart messaging to operate.

    Another thing pointing to the problem being with email that I have disabled all Push email for the iPad, and the password are stopped.  Then, when I try to retrieve messages manually, the prompt is displayed again.

    I'm out of ideas.  One thing I did not must give a new password, to disconnect all devices, then add them, one by one.

    Any help would be really appreciated.

    Thank you

    Dan

    Hello djborden,

    Thanks for this info and choosing the communities Support from Apple. I know the importance of the iCloud works correctly on your devices is for you! Looks like you've tried a few normal troubleshooting steps, and when I had a similar problem, I had to log out of my Apple ID in iCloud on all my devices, change the Apple ID password, restart devices and sign in iCloud. The following articles will help you through this process:

    1. log in your Apple ID for services iCloud on your devices, and then change your password Apple ID:

    Change your Apple ID password

    2. restart your devices, such as closing down and starting process is important to keep the software works correctly:

    Restart your iPhone, iPad or iPod touch

    How to turn on or off your Mac

    3. then, you can login with your password Apple ID updated and test again the question:

    What to do when you have changed your Apple ID email address or password

    See you soon!

  • I'm looking for a bluetooth headset that connects to both my iphone 6 and my air of ipad.  I have a Bose bluetooth connection that does work on my ipad.  Any recommendations?

    Recommendations for a bluetooth headset that works on the iphone 6 and ipad air?

    Most helmets will pair at least 2 sources; Check the manual of your Bose can also. But you must pair it both, and you must manually switch the connection when switching from one to the other. It can only connect to one at a time (this is a BT Protocol limit). I have a headset of parrot Zik that pairs up to 5 sources (I use it with 4).

  • loading slow iphone ipad and 6 Air since IOS9 last updated

    Since the update, my iphone IOS9 6 and ipad Air are recharged very slowly, I turned off all the juice sucking apps etc and there is still no improvement, ideas please?

    Install battery life: check the internal battery statistics on the... - iTunes and check the current load with your current charger. Then try another charger and check the intensity again to see if there is something wrong with your charger/lightning cable.

  • You can buy and 2 Air iPad smart case and use this case for the new iPad 9.7 Pro?

    can you get an iPad 2 case Air and use it for the new iPad 9.7 Pro

    You should be able to. Both devices have the same accurate external characteristics. I think that the physical difference is that the Pro 2 has 4 speakers and 2 Air has two. (Pro has two on top, two on the bottom, 2 Air just has two on the bottom)

    Yes, as long as the case is not "blocking the speakers or you don't care (I use only headphones with my iPad so I don't care if the speakers have been blocked)"

  • OfficeJet Pro 8600 - Macbook Pro and Macbook Air does not print

    Products:

    • HP Officejet Pro 8600
    • MacBook Pro (Mac OS X, Version 10.7.5)
    • MacBook Air (OS X, Version 10.8.2)

    Question:

    • Why my Mac initially print fine, but now will not print?

    Full article:

    I have a wireless network in my house that consisted of a 30 MB cable internet, Netgear 900n, HP Officejet Pro 8600, 2 laptops from Dell with Windows 7, a laptop Lenovo with Windows 7 and Dell with Windows 7 trick, all printed matter very well.

    The HP Officejet 8600 was added to my network about 2 months ago.

    I added a Macbook Pro and Macbook Air about 3 weeks ago.  The two Macs printed fine for about a week.  Then suddenly they stop.  I spent about 2 hours on the phone with HP's Service, and finally, they said to my router.  So I called Netgear.  NETGEAR was useless!  They wanted me to accept fees for services before they would even discuss the issue.

    As a result of information provided by the HP support service, and because Netgear will not support their product, I quickly bought a new router - an Apple Airport Extreme.

    Macs will recognize the printer will print if connected via a USB cable, but do not print wirelessly on the Officejet Pro 8600.  The fine impression CPA.

    The frustration that is felt is made up by the fact that Macs printed very well with the Officejet Pro 8600 2 weeks and now the printer shows just "idle"... even with a new router. (see image below)

    Please help, thank you very much for all support.

    As a side note, the representative of the HP Service was very friendly and definitely tried to support the HP product, which is much more I can say about Netgear.

    Thank you

    Hello

    More likely a problem with Multicast, which Apple devices are relies on to communicate with the device through the network.

    First try unplugging the router for 30 seconds.

    Connect to the power supply and wait 2-3 minutes.

    Turn off the HP printer and turn it back on, then check all difference.

    If it persists, try to change the configuration of your router as follows

    Note: the settings below are not related with the HP product, I provide you with the steps as a best efforts and those based only on my own knowledge. You can try to change the settings of the router at your own risk:

    1. Open the router configuration page (you'll find listed as the default gateway by clicking the icon on the printer wireless, then print a network configuration report.
    2. Click the Advanced tab.
    3. Click the configuration option in the menu, and then click Setup WAN.
    4. Be sure to uncheck the box Disable IGMP proxy transmission and apply the changes.
    5. Click on the LAN configuration on the same Setup menu.
    6. Set the RIP RIP-2 Version and apply the changes.
    7. Restart your router and then check any change.

    I hope that you will find useful information, you can also use the guide to the user below for more information:

    http://www.downloads.NETGEAR.com/files/GDC/WNDR4500/WNDR4500_UM_07DEC2011.PDF

    Shlomi

  • I have a book and an Air and would like to keep in sync how can I do?

    I have a Macbook and Mac Air and you want to keep them in sync, how do I do it?

    Mail can be synchronized by storing it in an e-mail server that uses the IMAP protocol, like iCloud. Mail remains on the server, it is automatically synchronized with all e-mail clients.

    Documents and several other types of data can be synchronized via iCloud, such as calendars, contacts, photos, Safari tabs and bookmarks and passwords. iCloud is easy to use, for the most part. The disadvantages of its use are, firstly, that it synchronizes everything; and second, that some of your personal information will be potentially accessible to foreigners. Read the list features iCloud and privacy notice carefully before deciding if or how to use it. There should be no problem with iCloud Keychain Access privacy, because data is encrypted end-to-end and are not accessible to anyone at Apple - but of course, you have to take the word Apple for that.

    A more complete solution and one that does not raise issues of confidentiality, is set up an OS X Server on your network and create mobile accounts on your other Mac. You will then be able to synchronize all files in the home folder automatically disconnected, or at any other time manually. The main drawback here is that OS X Server would be difficult for non-technical users more to install and maintain. Another is that synchronization only works with the Mac, mobile no.

    Third-party software can also be used to sync files on a network. I don't have a specific recommendation. The software may not be easy to implement in a way that does not lead to conflicts when files are changed on the various devices between synchronizations. To synchronize more than two Mac in this way, you'll want to use it as the master and synchronization between her and the others.

  • Cisco VCS and integration Lync2013

    Hello!

    Could you tell me please, when CISCO officially support Lync2013 - free new software for VCS - C and documentation on integration?

    The main interest is the possibility of transferring video between CISCO/MCU and Lync endpoints on the H.264 Protocol, who hails from Lync2013.

    Right now, I've got VCS - C and RTM Lync2013 X7.2. During the video call without AMGW appeal established as audio only.

    When using with Lync2010, it worked on Protocol H.263 and CIF resolution.

    Evgeniy salvation,

    We are currently investigating the possibilities to achieve interoperability between Lync 2013, VCS and video devices on the side of the VCS standards-based, it is a work in progress and at this stage, it is to early to provide any factual information on when interop will be available.

    In contrast to Lync 2010, Lync 2013 does not support H.263 for video and it so that will remove the OCS/Lync integration. I do however think that you should be able to make a two-way video between Lync 2013 and VCS-joined endpoints if you use an AMGW tried that yet?

    Thank you

    Andreas

Maybe you are looking for

  • Safari extension store question, links to the developers site

    For example, when trying to download LastPass extension via the link on the LastPass website, the link on the Safari extension store simply links to the page that I was right (site LastPass) who took me in the extension Safari store. In this case for

  • How to re-enable the prompt confirmation shift + delete?

    I don't like play with trash / recycling bins and have always used the shift + del for everything in Windows and other programs that support it. This includes Thunderbird. I think that I recently accidentally ticked the box 'don't show this again' on

  • Unable to start - blocked Windows updates to install updates

    original title: I can not connect after restarting my computer during updates. Help, please I have a Sony Vaio laptop running windows Vista (2008). It came pre loaded so I don't have an installation disc. I was in the middle of a huge update (windows

  • How to get my application attributes?

    Hello I want to get my application of attributes such as vendor, Version, title, and Description. And all that stuff to display on the screen inside my application. How can I get my application attributes? Code snippets? Best regards.

  • InDesign CS6 is an updated version of the Adobe Digital Editions software?

    When I click on the Adobe Digital Editions software on the Adobe Web site on my computer, a window titled "InDesign CS6' pop - up;  When I click on the Adobe Digital Editions software on the Adobe website on my iPad, a window titled 'Adobe Digital Ed