Cisco Aironet 1131AG and measure access points to the power of the wireless signal?

Similar Questions

• Several points of access Cisco Aironet 1131AG and same SSID?

  We have several Cisco Aironet 1131AG, all wired devices on a switch (2560) Cisco L2 which is connected to the L3 switch (3550). We have assigned a VLAN for access point to the L3 switch which acts as a vtp Server (L2 switch is vtp client). All the ap will have a static ip address and all will have the same SSID and no security, and they will use several channels (e.g. 1,6,11).  They will work in 3 floors for a roaming wireless client. We not using any wireless controller.

  So my question is this: how to configure the same APs-all with a different ip address, can we use L3 switch to create the dhcp server to access points VLAN (pool for guests) and the rest of the static ip address for the ap? One of the ap can be WDS and on the same radius server local time with users without Cisco Secure ACS or similar controller or I did not understand this very well :-). I followed the guide http://www.cisco.com/en/US/docs/wireless/access_point/12.3_2_JA/configuration/guide/s32roamg.html for WDS where Abu Cisco ACS part is a problem, so I can use the same ap as a Local authenticator as a guide http://www.cisco.com/en/US/docs/wireless/access_point/12.3_4_JA/configuration/guide/s34local.html#wp1035723.

  Thank you very much...

  Well, just so you know, WDS, and local RADIUS authentication is necessary only if you use authentication on your wireless connection.  You say that you do not plan to use security, so it's not necessary.  However, I highly recommend at least using a simple WPA2-PSK to lock your connection, otherwise you might end up giving free Internet access at best and at worst you could give access to the computers and corporate servers.  If you want to reuse a 802. 1 x or WPA authentication method, then Yes, you can use an AP as RADIUS and to improve WDS Server authenticated to roaming, but this is much more limited than the use of a Cisco ACS.

  As for your other questions, Yes, your APs can all be configured the same except for at least three settings: IP address, hostname, and channel.  Configure your static IP addresses on the interface of the PA BVI1.  Do not place it on the Radio or Ethernet interfaces, because if one of these interfaces goes down, you lose the ability to configure the AP, so it's best to use the BVI1 interface.

  And Yes, configure a DHCP scope for your customers on your L3 switch is good design, or you can also use your DHCP server on a different subnet by using the command of support-ip address on the interface of L3.  I hope this helps!  Let me know if you need help to set all this up.

  Merry Christmas!

  Jeff

• Windows 7 or 8 shows the wireless client connected to the access point, but the wireless icon displays "no internet connection".

  I saw the same problem with a different providers wireless solution. When I've sniffed the air with OmniPeek and the network that the ap was conducting with WireShark, I see the arp for the gateway request going to the router, the router gateway response is sent to the suspect machine in the air, the acknowledgement of PC than the package but never fills the arp cache. I watched two arp responses in a vs work for lack of scenario, the two packages are the same.

  The only way I could solve it was to disable IP Helper (not start too) services, reboot the machine. I see 3 to 4 drops per day, but since the deactivation of this Service the machines with that I tested have not seen the question once again.

  IP Helper:
  Provides tunnel connectivity using technologies of transition IPv6 (6to4, ISATAP, Teredo, and Port Proxy) and IP-HTTPS. If this service is stopped, the computer will not have the benefits of improved connectivity offered by these technologies.

  Machines tested and fixed:

  Lenovo E540
  Lenovo W540
  Acer Aspire One
  Dell Latitude E6420

  Ip assistance service has been changed about 40 laptops, a dozen of which would fail in about an hour. So far, 0 out of the 40 saw the question since this change and reboot (reset is the key after disable it) laptops. It's been about 5 days.

  Any reason why disable this Service solves the problem? With it I can replicate the problem pretty quickly on a few different types of machines so it seems not to be driver or provider specific wireless network card. I checked through the Event Viewer logs, but nothing seems to be triggered during the show. Using the Troubleshooter or disconnect the wireless service will fix the problem for a short period only.

  Hello

  The question you posted would be better suited in the TechNet Forums. I would recommend posting your query in the TechNet Forums.
   
  TechNet Forum
  http://social.technet.Microsoft.com/forums/Windows/en-us/home?filter=AllTypes&sort=lastpostdesc&brandIgnore=true

  Hope this information is useful.

• Set up the wireless access point, but the wireless devices are unable to get ip address

  Hi, I wanted to put my D7000 as router AP. My main router is Sagemcom F@st 3864 by Optus ISP (Australia).

  First of all, I put the D7000 in Bridge mode I did these steps:

  1. replace the IP LAN 192.168.0.100

  2 disable DHCP

  3. connect the LAN port to the main router Lan port

  Internet connection wired and wireless on the same device but other wireless devices has failed

  To remedy this, I made another choice, allowing point-to-point wireless access in the advanced settings of the D7000. I followed the instructions from this link

  http://KB.NETGEAR.com/app/answers/detail/A_ID/24104/~/how-do-i-change-my-Nighthawk-router-to-AP-mode...

  I put dynamiccaly = wireless internet cable success but peripheral does not have an ip address

  No idea how to fix wireless? I'm not very experienced

  Thank you!

  I just fixed it just now. For AP mode, connect the LAN port of the main router to the WAN port on the D7000 (not LAN to LAN). I wish I thought to it much sooner.

• Cisco aironet 1131AG AP radio interface down

  Hello
  I have a problem with my cisco aironet 1131ag AP radio interface.
  I configured the ssid, authentication and encryptation me have it (the ssid) associated with the radio interface, but the interface of dot11radio still in a State of remission to zero, and if a restart the interface this msg appears "% DOT11-4-NO_SSID: no SSID configured." Not started Dot11Radio0 ' what I need to do?
  Help, please

  Configuration:

  Building configuration...

  Current configuration: 1394 bytes
  !
  version 12.4
  no service button
  horodateurs service debug datetime msec
  Log service timestamps datetime msec
  encryption password service
  !
  host ap name
  !
  Select the 5 secret $1$ Mf3YfBFQQS2.6MSWHQOeG0 $URAK
  !
  No aaa new-model
  domain IP Nida.local
  !
  !
  !
  dot11 ssid Nida
  VLAN 1
  open authentication
  authentication wpa key management
  Comments-mode
  WPA - psk ascii 7 01100F175804575D72
  admit-traffic
  !
  !
  diet pre-standard trading online
  !
  !
  username Cisco privilege 15 password 7 123A0C041104
  !
  Bridge IRB
  !
  !
  interface Dot11Radio0
  IP 192.168.1.80 255.255.255.0
  no ip route cache
  !
  algorithms for encryption tkip encryption mode
  !
  encryption vlan 1 tkip encryption mode
  !
  SSID Nida
  !
  root of station-role
  Bridge-Group 1
  Bridge-group subscriber-loop-control 1
  Bridge-Group 1 block-unknown-source
  No source of bridge-Group 1-learning
  unicast bridge-Group 1-floods
  Bridge-Group 1 covering-disabled people
  !
  interface FastEthernet0
  192.168.1.81 IP address 255.255.255.0
  no ip route cache
  automatic duplex
  automatic speed
  Bridge-Group 1
  No source of bridge-Group 1-learning
  Bridge-Group 1 covering-disabled people
  !
  interface BVI1
  customer_id FastEthernet0 dhcp IP address
  no ip route cache
  !
  IP http server
  no ip http secure server
  IP http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
  1 channel ip bridge
  !
  !
  !
  Line con 0
  line vty 0 4
  local connection
  !
  end

  You must create the dot11radio0.1 and fastethernet0.1 interface

  Must be something like this:

  version 12.4
  no service button
  horodateurs service debug datetime msec
  Log service timestamps datetime msec
  encryption password service
  !
  host ap name
  !
  Select the 5 secret $1$ Mf3YfBFQQS2.6MSWHQOeG0 $URAK
  !
  No aaa new-model
  domain IP Nida.local
  !
  !
  !
  dot11 ssid Nida
  VLAN 1
  open authentication
  authentication wpa key management
  Comments-mode
  WPA - psk ascii 7 01100F175804575D72
  admit-traffic
  !
  !
  diet pre-standard trading online
  !
  !
  !
  Bridge IRB
  !
  !
  interface Dot11Radio0
  no ip route cache
  !
  algorithms for encryption tkip encryption mode
  !
  encryption vlan 1 tkip encryption mode
  !
  SSID Nida
  !
  root of station-role

  interface dot11radio0.1
  encapsulation dot1q 1 native
  Bridge-Group 1
  Bridge-group subscriber-loop-control 1
  Bridge-Group 1 block-unknown-source
  No source of bridge-Group 1-learning
  unicast bridge-Group 1-floods
  Bridge-Group 1 covering-disabled people
  !
  interface FastEthernet0
  no ip route cache
  automatic duplex
  automatic speed
   
  interface Fastethernet0.1
  encapsulation dot1q 1 native
  192.168.1.81 IP address 255.255.255.0
  Bridge-Group 1
  No source of bridge-Group 1-learning
  Bridge-Group 1 covering-disabled people
  !
  interface BVI1
  customer_id FastEthernet0 dhcp IP address
  no ip route cache
  !
  IP http server
  no ip http secure server
  IP http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
  1 channel ip bridge
  !
  !
  !
  Line con 0
  line vty 0 4
  local connection
  !
  end

  PS has also removed the ip address dot11 interface slot and I'm not sure why the role of station is root?

• Launch of Lightroom 6 is not. error: "can't find the access point of the procedure _crtCreateSymbolicLinkW in the MSVCR110.dll dynamic link library.

  It says: "cannot find the access point of the procedure _crtCreateSymbolicLinkW in the MSVCR110.dll dynamic link library. What can I do? I have already uninstall and then reinstall the software...

  It is indeed a microsoft problem, check here:error "did not find the entry point _crtCreateSymbolicLinkW - Microsoft Community .

• my standard drawing tools in a given paper seem to be stuck in some kind of preset isometric drawing. someone knows how to get back to 'normal '. my cursor has a cross and an arrow pointing to the left.

  Hoping that this is easy. my standard drawing tools in a given paper seem to be stuck in some kind of preset isometric drawing. someone knows how to get back to 'normal '. my cursor has a cross and an arrow pointing to the left.

  disable the perspective grid. Shift + ctrl + I

• SNMP and cisco Aironet 1131AG

  We have a wireless control system, 3 WLC and 190 APs. I need to listen to 802.11 radios via SNMP. The system is running with LWAPP and APs are not accessible via SNMP (no response trying to access). I'm trying to send traps on the Server SNMP (Zabbix) but to disable the WLC 802.11 Radio, I don't see any trap regarding the status of the Radio or the admin down.

  Are you looking for it any method to monitor the status of the radio via SNMP?

  Thanks in advance,

  OLAF

  Hi Olaf,.

  Lwapp APs are not snmp manageable but controllers takes care of this. You can query the WLC via SNMP and it will give you the status of all access points radio.

  I suggest to use the tool of Cisco's MIB browser learn more about AIRESPACE mib that uses the WLC.

  Nicolas

• Cisco WLC license evaluation of Access Point

  Hello

  I would like to know what is happening to access connected to a Cisco WLC points if the evaluation license reached its expiration date and other licenses have not yet been installed all connected access points would cease immediately operation?

  Kind regards

  Mark

  Yes, they would stop working.

  Note: when you add licenses a reboot is required. Even if the number of supported the HA increases on reset controller is always necessary for these devices to register on the controller under the permanent license. I once added licenses and when I saw the number of the AP increase - I experimented with the restart - and when evaluating lic. expiration of my AP dropped the controller.

• Create the Pool DHCP on Cisco Aironet 1131AG

  Hello

  How to create a DHCP on a Cisco Aironet pool so that laptops could get an IP address from this range when connected?

  I don't want to use DHCP on our servers because these laptops are to be on a separate network.

  Just do not know what commands to use.

  Thank you!

  Hello

  There is a nice step by step to configure the DHCP Service on the AP in this doc;

  Configuration of the Access Point to provide DHCP Service

  http://www.Cisco.com/en/us/docs/wireless/access_point/12.3_8_JA/configuration/guide/s38adm.html#wp1090319

  I hope this helps!

  Rob

  Thank you to support CSC helps Haiti

  https://supportforums.Cisco.com/docs/doc-8895

  https://supportforums.Cisco.com/docs/doc-8727

• Unique to the multiple SSID and possible access point single channel?

  Hello world.

  I have a silly question.

  Let say, we have three VLAN, vlan1, 2, 3 and they are mapped to the following wireless LANs:

  VLAN 1 ssid1

  VLAN 2 ssid2

  Vlan3 ssid 3

  AP - trunk - dagprogramm network.

  Our access point has mobile devices in three local wireless networks, IE ssid1ssid2 and ssid3

  Since the mode AP use half duplex, mobile devices need acknowledgement positive to ap they can send data, so once channel let channel 3 (assuming that 802. 11b is used) can be shared by all the devices in three local wireless networks.

  My understanding is correct?

  Thanks and a great weekend.

  An access point = an associated action related channel and each ssid and the customer that one channel and the AP is essentially as a hub

  concerning

  Joe

• Cisco linksys router and cannot access the wireless network

  We have cisco linksys wireless router.  When we installed everything first, we could connect our wireless laptops to the network.  Now, however, the network is detected, but there is no access to the internet.  We have even a guy from ATT were out and he said that the wireless router has been installed backwards?  He installed a dsl fast access on our laptop icon, and now we can access the wireless network but only if we connect as the first.  We can also connect iPod to the wireless network.  They detect the network, but when we enter the password cannot connect.

  Hi JC_3094,

  Welcome to the Microsoft Community and thanks for posting the question.

  According to the description, it looks like you aren't able to access the Internet.

  The likely causes of this problem is if the router is not configured properly.

  Here are some steps that should help you to solve this problem.

  Method 1:

  Check if the router is configured properly to get access to the Internet.

  Method 2:

  Try the steps mentioned in this link and check:

  This tutorial is designed to help you identify and solve problems with a wired (Ethernet) and wireless (Wi - Fi) network connections in Windows.

  Wireless and wired network problems
  http://Windows.Microsoft.com/en-us/Windows/network-connection-problem-help#network-problems=Windows-7&V1H=win8tab1&V2H=win7tab1&V3H=winvistatab1&v4h=winxptab1

   

  Method 3:

   

  If there is a frequent disconnection try to update the firmware on the router and check.

   

  In addition, visit these links for more information:

   

  Why can't I connect to the Internet?

  http://Windows.Microsoft.com/en-us/Windows7/why-can-t-I-connect-to-the-Internet

   

  Hope this information helps. Respond us if you have any questions with windows and we will be happy to help.

• Access point of the AIR-CAP1602E-N-K9

  Hello

  can someone help me set up AIR-CAP1602E-N-K9 as autonomous access point.

  This is a new default affecting by my knowledge, it's a point of access controller based pls if help how to convert in autonomous access point and the image that is compatible with that.

  Hi Kamal,

  Hope links below will keep you started with LWAP autonomous.

  http://www.Cisco.com/en/us/docs/wireless/access_point/conversion/LWAPP/u...

  https://supportforums.Cisco.com/docs/doc-14960

  http://mrncciew.com/2012/10/20/lightweight-to-autonomous-conversion/

  For standalone AP, you can use the configuration below. In the link below, you can skip the configuration under 'bridge Configuration.

  https://supportforums.Cisco.com/document/61936/autonomous-AP-and-bridge-...

  Hope that helps.

  Concerning

  Najaf

• Updating of the access points in the environment, the models?

  I'm going slow in the environment by replacing the access points 80 AIR-1252.  I decided to replace our 1142 s at the same time so that the environment is up to date.  I was curious what the replacement recommended for these access points.  I see Cisco recommends the 1262 in lieu of the 1252.

  I work for an oil and gas company with locations across the country.  We use two 5508 s with Flex Connect runs the last code 7.3 7.4 into account in the next 6 months.  Our sites are a mixture of office space with warehouse or other environments difficult. I think 2602 s to replace the 1142 s and 1252 s mounted in offices, and I'm leading 1242 s to replace the 1252 s mounted in our warehouse/truck Bay environments.

  Well the 1262 did replace the 1252, but then Cisco came out with the 3502e and the 3602e.  Then maybe you should look at is using the 2602i in the office areas and maybe the 2602e in the area rugged or even look at the 3502e/3602e.  This way, you have all the AP that can sustain CleanAir.

  Thank you

  Scott

  Help others by using the rating system and marking answers questions as 'response '.

• Print Epson printer States: a router/access point channel conflict detected - improve your wireless network environment?

  I try to print from my laptop on my Epson printer.  It will not work on any of the documents or the internet.  The Epson prints what follows: a conflict of channel router/access point - improve your wireless network environment, has been detected.  My router is sitting next to my printer and the laptop.  The Green WiFi light on the front of the printer is on.  I have no problem using my Ipad in the other room.  So does mean printing?

  It's that all the documents, both new & saved and the same Wordpad?

  Maybe

  http://support.Epson.ru/products/manuals/102044/Panel/g_html/external/manual_e01.htm