Cisco ASA 5508 with firepower of speeds VPN

Similar Questions

• Cisco ASA 8.4 (3) remote access VPN - client connects but cannot access inside the network

  I have problems to access the resources within the network when connecting with the Cisco VPN client for a version of 8.4 (3) operation of the IOS Cisco ASA 5510. I tried all new NAT 8.4 orders but cannot access the network interior. I can see traffic in newspapers when ping. I can only assume I have NAT evil or it's because the inside interface of the ASA is on the 24th of the same subnet as the network interior? Please see config below, any suggestion would be appreciated. I configured a VPN site to another in this same 5510 and it works well

  Thank you

  interface Ethernet0/0

  Speed 100

  full duplex

  nameif outside

  security-level 0

  IP x.x.x.x 255.255.255.240

  !

  interface Ethernet0/1

  Speed 100

  full duplex

  nameif inside

  security-level 100

  IP 10.88.10.254 255.255.255.0

  !

  interface Management0/0

  Shutdown

  nameif management

  security-level 0

  no ip address

  !

  permit same-security-traffic inter-interface

  permit same-security-traffic intra-interface

  network of the PAT_to_Outside_ClassA object

  10.88.0.0 subnet 255.255.0.0

  network of the PAT_to_Outside_ClassB object

  subnet 172.16.0.0 255.240.0.0

  network of the PAT_to_Outside_ClassC object

  Subnet 192.168.0.0 255.255.240.0

  network of the LocalNetwork object

  10.88.0.0 subnet 255.255.0.0

  network of the RemoteNetwork1 object

  Subnet 192.168.0.0 255.255.0.0

  network of the RemoteNetwork2 object

  172.16.10.0 subnet 255.255.255.0

  network of the RemoteNetwork3 object

  10.86.0.0 subnet 255.255.0.0

  network of the RemoteNetwork4 object

  10.250.1.0 subnet 255.255.255.0

  network of the NatExempt object

  10.88.10.0 subnet 255.255.255.0

  the Site_to_SiteVPN1 object-group network

  object-network 192.168.4.0 255.255.254.0

  object-network 172.16.10.0 255.255.255.0

  object-network 10.0.0.0 255.0.0.0

  outside_access_in deny ip extended access list a whole

  inside_access_in of access allowed any ip an extended list

  11 extended access-list allow ip 10.250.1.0 255.255.255.0 any

  outside_1_cryptomap to access extended list ip 10.88.0.0 255.255.0.0 allow object-group Site_to_SiteVPN1

  mask 10.250.1.1 - 10.250.1.254 255.255.255.0 IP local pool Admin_Pool

  NAT static NatExempt NatExempt of the source (indoor, outdoor)

  NAT (inside, outside) static source any any static destination RemoteNetwork4 RemoteNetwork4-route search

  NAT static LocalNetwork LocalNetwork destination (indoor, outdoor) static source RemoteNetwork1 RemoteNetwork1

  NAT static LocalNetwork LocalNetwork destination (indoor, outdoor) static source RemoteNetwork2 RemoteNetwork2

  NAT static LocalNetwork LocalNetwork destination (indoor, outdoor) static source RemoteNetwork3 RemoteNetwork3

  NAT (inside, outside) static source LocalNetwork LocalNetwork static destination RemoteNetwork4 RemoteNetwork4-route search

  !

  network of the PAT_to_Outside_ClassA object

  NAT dynamic interface (indoor, outdoor)

  network of the PAT_to_Outside_ClassB object

  NAT dynamic interface (indoor, outdoor)

  network of the PAT_to_Outside_ClassC object

  NAT dynamic interface (indoor, outdoor)

  Access-group outside_access_in in interface outside

  inside_access_in access to the interface inside group

  Route outside 0.0.0.0 0.0.0.0 x.x.x.x 1

  dynamic-access-policy-registration DfltAccessPolicy

  Sysopt connection timewait

  Service resetoutside

  Crypto ipsec transform-set ikev1 ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac

  Crypto ipsec transform-set ikev1 ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac

  Crypto ipsec transform-set ikev1 ESP-AES-192-SHA esp-aes-192 esp-sha-hmac

  Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-esp - aes esp-md5-hmac

  Crypto ipsec transform-set esp-ikev1 esp-md5-hmac bh-series

  Crypto ipsec transform-set ikev1 esp ESP-DES-MD5-esp-md5-hmac

  Crypto ipsec transform-set ikev1 ESP-3DES-MD5-esp-3des esp-md5-hmac

  Crypto ipsec transform-set ikev1 ESP-DES-SHA esp - esp-sha-hmac

  Crypto ipsec transform-set ikev1 ESP-AES-128-SHA aes - esp esp-sha-hmac

  Crypto ipsec transform-set ikev1 ESP-AES-256-SHA esp-aes-256 esp-sha-hmac

  Crypto ipsec transform-set ikev1 SHA-ESP-3DES esp-3des esp-sha-hmac

  Crypto-map dynamic dynmap 10 set pfs

  Crypto-map dynamic dynmap 10 set transform-set bh - set ikev1

  life together - the association of security crypto dynamic-map dynmap 10 28800 seconds

  Crypto-map dynamic dynmap 10 kilobytes of life together - the association of safety 4608000

  Crypto-map dynamic dynmap 10 the value reverse-road

  card crypto mymap 1 match address outside_1_cryptomap

  card crypto mymap 1 set counterpart x.x.x.x

  card crypto mymap 1 set transform-set ESP-AES-256-SHA ikev1

  card crypto mymap 86400 seconds, 1 lifetime of security association set

  map mymap 1 set security-association life crypto kilobytes 4608000

  map mymap 100-isakmp ipsec crypto dynamic dynmap

  mymap outside crypto map interface

  crypto isakmp identity address

  Crypto isakmp nat-traversal 30

  Crypto ikev1 allow outside

  IKEv1 crypto ipsec-over-tcp port 10000

  IKEv1 crypto policy 5

  preshared authentication

  3des encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 10

  preshared authentication

  3des encryption

  sha hash

  Group 1

  life 86400

  IKEv1 crypto policy 50

  preshared authentication

  the Encryption

  md5 hash

  Group 2

  life 86400

  IKEv1 crypto policy 60

  preshared authentication

  aes-256 encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 70

  preshared authentication

  aes-256 encryption

  sha hash

  Group 1

  life 86400

  IKEv1 crypto policy 90

  preshared authentication

  aes encryption

  sha hash

  Group 2

  life 86400

  Telnet timeout 5

  Console timeout 0

  management-access inside

  a basic threat threat detection

  Statistics-list of access threat detection

  no statistical threat detection tcp-interception

  WebVPN

  internal BACKDOORVPN group policy

  BACKDOORVPN group policy attributes

  value of VPN-filter 11

  Ikev1 VPN-tunnel-Protocol

  Split-tunnel-policy tunnelall

  BH.UK value by default-field

  type tunnel-group BACKDOORVPN remote access

  attributes global-tunnel-group BACKDOORVPN

  address pool Admin_Pool

  Group Policy - by default-BACKDOORVPN

  IPSec-attributes tunnel-group BACKDOORVPN

  IKEv1 pre-shared-key *.

  tunnel-group x.x.x.x type ipsec-l2l

  tunnel-group ipsec-attributes x.x.x.x

  IKEv1 pre-shared-key *.

  !

  class-map inspection_default

  match default-inspection-traffic

  !

  !

  type of policy-card inspect dns preset_dns_map

  parameters

  maximum message length automatic of customer

  message-length maximum 512

  Policy-map global_policy

  class inspection_default

  inspect the preset_dns_map dns

  inspect the ftp

  inspect h323 h225

  inspect the h323 ras

  inspect the rsh

  inspect the rtsp

  inspect esmtp

  inspect sqlnet

  inspect the skinny

  inspect sunrpc

  inspect xdmcp

  inspect the sip

  inspect the netbios

  inspect the tftp

  Review the ip options

  !

  global service-policy global_policy

  Excellent.

  Evaluate the useful ticket.

  Thank you

  Rizwan James

• Failover on Cisco ASA 5505 with EasyVPN

  Hello

  I've implemented a customer EasyVPN with a Cisco ASA 5505 and I am trying to configure the failover but I get this message:

  "Failover cannot be configured as Cisco Easy VPN remote is activated."

  However, I have seen in the link below, this dynamic rollover is compatible with the easy standard (and not with improved but I don't think I use easyVPN improved).

  http://www.Cisco.com/c/en/us/products/collateral/security/iOS-easy-VPN/e...

  The configuration I did through ASDM is very simple:

  vpnclient server * * *.
  vpnclient-mode client mode
  vpngroup vpnclient * password *.
  vpnclient username * password *.
  vpnclient enable

  My question is how can I implement failover with a client on a Cisco ASA 5505 EasyVPN?

  Thanks in advance

  You cannot configure the failover of a device that acts as a client

• EzVPN between Cisco ASA 5505 (with NEM mode) and Ciscoo 881 Roure

  Hi friends,

  I configured the Cisco ASA 5505 and Cisco router with DMVPN 881. 3 offices works very well but one office remains failure. I did the same configuration for all facilities but this router does not work. Any ideas?

  Please find below the exit of 881 router Cisco:

  YF2_Tbilisi_router #.
  * 4 August 09:31:26.793: ISAKMP: (0): transmit phase 1 AG_INIT_EXCH...
  * 09:31:26.793 4 August: ISAKMP (0): increment the count of errors on his, try 4 out 5: retransmit the phase 1
  * 4 August 09:31:26.793: ISAKMP: (0): transmit phase 1 AG_INIT_EXCH
  * 4 August 09:31:26.793: ISAKMP: (0): 1.1.1.1 package sending 500 peer_port 500 (I) my_port AG_INIT_EXCH
  * 09:31:26.793 4 August: ISAKMP: (0): sending a packet IPv4 IKE.
  * 4 August 09:31:36.793: ISAKMP: (0): transmit phase 1 AG_INIT_EXCH...
  * 09:31:36.793 4 August: ISAKMP (0): increment the count of errors on his, try 5 of 5: retransmit the phase 1
  * 4 August 09:31:36.793: ISAKMP: (0): transmit phase 1 AG_INIT_EXCH
  * 4 August 09:31:36.793: ISAKMP: (0): 1.1.1.1 package sending 500 peer_port 500 (I) my_port AG_INIT_EXCH
  * 09:31:36.793 4 August: ISAKMP: (0): sending a packet IPv4 IKE.
  * 09:31:44.929 4 August: ISAKMP: (0): serving SA., its is 88961 B 34, delme is 88961 B 34
  * 4 August 09:31:46.793: ISAKMP: (0): transmit phase 1 AG_INIT_EXCH...
  * 09:31:46.793 4 August: ISAKMP: (0): the peer is not paranoid KeepAlive.

  * 09:31:46.793 4 August: ISAKMP: (0): removal of reason ITS status of 'Death by retransmission P1' (I) AG_INIT_EXCH (peer 1.1.1.1)
  * 09:31:46.793 4 August: % CRYPTO-6-EZVPN_CONNECTION_DOWN: user (customer) = group = Youth_Facility_2 Server_public_addr = 1.1.1.1
  * 4 August 09:31:46.793: ISAKMP:isadb_key_addr_delete: no key for address 1.1.1.1 (root NULL)
  * 09:31:46.793 4 August: ISAKMP: (0): removal of reason ITS status of 'Death by retransmission P1' (I) AG_INIT_EXCH (peer 1.1.1.1)
  * 09:31:46.793 4 August: ISAKMP: Unlocking counterpart struct 0x8AA90C50 for isadb_mark_sa_deleted(), count 0
  * 09:31:46.793 4 August: ISAKMP: delete peer node by peer_reap for 1.1.1.1: 8AA90C50
  * 09:31:46.793 4 August: ISAKMP: (0): entry = IKE_MESG_INTERNAL, IKE_PHASE1_DEL
  * 09:31:46.793 4 August: ISAKMP: (0): former State = new State IKE_I_AM1 = IKE_DEST_SA

  * 4 August 09:31:47.805: del_node 2.2.2.2 src dst 1.1.1.1:500 fvrf 0 x 0, ivrf 0 x 0
  * 09:31:47.805 4 August: ISAKMP: (0): the peer is not paranoid KeepAlive.

  * 4 August 09:31:47.805: ISAKMP: (0): profile of THE request is (NULL)
  * 09:31:47.805 4 August: ISAKMP: created a struct peer 1.1.1.1, peer port 500
  * 09:31:47.805 4 August: ISAKMP: new created position = 0x8AA90C50 peer_handle = 0 x 80004819
  * 09:31:47.805 4 August: ISAKMP: lock struct 0x8AA90C50, refcount 1 to peer isakmp_initiator
  * 09:31:47.805 4 August: ISAKMP: (0): client configuration parameters 87531228 adjustment
  * 09:31:47.805 4 August: ISAKMP: 500 local port, remote port 500
  * 09:31:47.805 4 August: ISAKMP: find a dup her to the tree during his B 88961, 34 = isadb_insert call BVA
  * 4 August 09:31:47.805: ISAKMP: (0): set up client mode.
  * 4 August 09:31:47.805: ISAKMP: (0): built of NAT - T of the seller-rfc3947 ID
  * 4 August 09:31:47.805: ISAKMP: (0): built the seller-07 ID NAT - t
  * 4 August 09:31:47.805: ISAKMP: (0): built of NAT - T of the seller-03 ID
  * 4 August 09:31:47.805: ISAKMP: (0): built the seller-02 ID NAT - t
  * 4 August 09:31:47.805: ISKAMP: more send buffer from 1024 to 3072
  * 09:31:47.805 4 August: ISAKMP: (0): ITS been pre-shared key and XAUTH authentication using id ID_KEY_ID type
  * 09:31:47.805 4 August: ISAKMP (0): payload ID
  next payload: 13
  type: 11
  Group ID: Youth_Facility_2
  Protocol: 17
  Port: 0
  Length: 24
  * 09:31:47.805 4 August: ISAKMP: (0): the total payload length: 24
  * 09:31:47.809 4 August: ISAKMP: (0): entry = IKE_MESG_FROM_IPSEC, IKE_SA_REQ_AM
  * 09:31:47.809 4 August: ISAKMP: (0): former State = new State IKE_READY = IKE_I_AM1

  * 4 August 09:31:47.809: ISAKMP: (0): Beginner aggressive Mode Exchange
  * 4 August 09:31:47.809: ISAKMP: (0): 1.1.1.1 package sending 500 peer_port 500 (I) my_port AG_INIT_EXCH
  * 09:31:47.809 4 August: ISAKMP: (0): sending a packet IPv4 IKE.
  * 4 August 09:31:57.809: ISAKMP: (0): transmit phase 1 AG_INIT_EXCH...
  * 09:31:57.809 4 August: ISAKMP (0): increment the count of errors on his, try 1 5: retransmit the phase 1
  * 4 August 09:31:57.809: ISAKMP: (0): transmit phase 1 AG_INIT_EXCH
  * 4 August 09:31:57.809: ISAKMP: (0): 1.1.1.1 package sending 500 peer_port 500 (I) my_port AG_INIT_EXCH
  * 09:31:57.809 4 August: ISAKMP: (0): sending a packet IPv4 IKE.
  * 4 August 09:32:07.809: ISAKMP: (0): transmit phase 1 AG_INIT_EXCH...
  * 09:32:07.809 4 August: ISAKMP (0): increment the count of errors on his, try 2 of 5: retransmit the phase 1
  * 4 August 09:32:07.809: ISAKMP: (0): transmit phase 1 AG_INIT_EXCH
  * 4 August 09:32:07.809: ISAKMP: (0): 1.1.1.1 package sending 500 peer_port 500 (I) my_port AG_INIT_EXCH
  * 09:32:07.809 4 August: ISAKMP: (0): sending a packet IPv4 IKE.
  * 4 August 09:32:17.809: ISAKMP: (0): transmit phase 1 AG_INIT_EXCH...
  * 09:32:17.809 4 August: ISAKMP (0): increment the count of errors on his, try 3 of 5: retransmit the phase 1
  * 4 August 09:32:17.809: ISAKMP: (0): transmit phase 1 AG_INIT_EXCH
  * 4 August 09:32:17.809: ISAKMP: (0): 1.1.1.1 package sending 500 peer_port 500 (I) my_port AG_INIT_EXCH
  * 09:32:17.809 4 August: ISAKMP: (0): sending a packet IPv4 IKE.
  * 4 August 09:32:27.809: ISAKMP: (0): transmit phase 1 AG_INIT_EXCH...
  * 09:32:27.809 4 August: ISAKMP (0): increment the count of errors on his, try 4 out 5: retransmit the phase 1
  * 4 August 09:32:27.809: ISAKMP: (0): transmit phase 1 AG_INIT_EXCH
  * 4 August 09:32:27.809: ISAKMP: (0): 1.1.1.1 package sending 500 peer_port 500 (I) my_port AG_INIT_EXCH
  * 09:32:27.809 4 August: ISAKMP: (0): sending a packet IPv4 IKE.
  * 4 August 09:32:37.809: ISAKMP: (0): transmit phase 1 AG_INIT_EXCH...
  * 09:32:37.809 4 August: ISAKMP (0): increment the count of errors on his, try 5 of 5: retransmit the phase 1
  * 4 August 09:32:37.809: ISAKMP: (0): transmit phase 1 AG_INIT_EXCH
  * 4 August 09:32:37.809: ISAKMP: (0): 1.1.1.1 package sending 500 peer_port 500 (I) my_port AG_INIT_EXCH
  * 09:32:37.809 4 August: ISAKMP: (0): sending a packet IPv4 IKE.
  * 09:32:46.793 4 August: ISAKMP: (0): serving SA., his is 872E1504, delme is 872E1504
  * 4 August 09:32:47.809: ISAKMP: (0): transmit phase 1 AG_INIT_EXCH...
  * 09:32:47.809 4 August: ISAKMP: (0): the peer is not paranoid KeepAlive.

  * 09:32:47.809 4 August: ISAKMP: (0): removal of reason ITS status of 'Death by retransmission P1' (I) AG_INIT_EXCH (peer 1.1.1.1)
  * 09:32:47.809 4 August: % CRYPTO-6-EZVPN_CONNECTION_DOWN: user (customer) = group = Youth_Facility_2 Server_public_addr = 1.1.1.1
  * 4 August 09:32:47.809: ISAKMP:isadb_key_addr_delete: no key for address 1.1.1.1 (root NULL)
  * 09:32:47.809 4 August: ISAKMP: (0): removal of reason ITS status of 'Death by retransmission P1' (I) AG_INIT_EXCH (peer 1.1.1.1)
  * 09:32:47.809 4 August: ISAKMP: Unlocking counterpart struct 0x8AA90C50 for isadb_mark_sa_deleted(), count 0
  * 09:32:47.809 4 August: ISAKMP: delete peer node by peer_reap for 1.1.1.1: 8AA90C50
  * 09:32:47.809 4 August: ISAKMP: (0): entry = IKE_MESG_INTERNAL, IKE_PHASE1_DEL
  * 09:32:47.809 4 August: ISAKMP: (0): former State = new State IKE_I_AM1 = IKE_DEST_SA

  * 4 August 09:32:48.909: del_node src 2.2.2.2:500 dst 1.1.1.1:500 fvrf 0 x 0, ivrf 0 x 0
  * 09:32:48.909 4 August: ISAKMP: (0): the peer is not paranoid KeepAlive.

  * 4 August 09:32:48.909: ISAKMP: (0): profile of THE request is (NULL)
  * 09:32:48.909 4 August: ISAKMP: created a struct peer 1.1.1.1, peer port 500
  * 09:32:48.909 4 August: ISAKMP: new created position = 0x8AA90C50 peer_handle = 0 x 80004818
  * 09:32:48.909 4 August: ISAKMP: lock struct 0x8AA90C50, refcount 1 to peer isakmp_initiator
  * 09:32:48.909 4 August: ISAKMP: (0): client setting Configuration parameters 88C05A48
  * 09:32:48.909 4 August: ISAKMP: 500 local port, remote port 500
  * 09:32:48.909 4 August: ISAKMP: find a dup her to the tree during the isadb_insert his 87B57D38 = call BVA
  * 4 August 09:32:48.909: ISAKMP: (0): set up client mode.
  * 4 August 09:32:48.909: ISAKMP: (0): built of NAT - T of the seller-rfc3947 ID
  * 4 August 09:32:48.909: ISAKMP: (0): built the seller-07 ID NAT - t
  * 4 August 09:32:48.909: ISAKMP: (0): built of NAT - T of the seller-03 ID
  * 4 August 09:32:48.909: ISAKMP: (0): built the seller-02 ID NAT - t
  * 4 August 09:32:48.909: ISKAMP: more send buffer from 1024 to 3072
  * 09:32:48.913 4 August: ISAKMP: (0): ITS been pre-shared key and XAUTH authentication using id ID_KEY_ID type
  * 09:32:48.913 4 August: ISAKMP (0): payload ID
  next payload: 13
  type: 11
  Group ID: Youth_Facility_2
  Protocol: 17
  Port: 0
  Length: 24
  * 09:32:48.913 4 August: ISAKMP: (0): the total payload length: 24
  * 09:32:48.913 4 August: ISAKMP: (0): entry = IKE_MESG_FROM_IPSEC, IKE_SA_REQ_AM
  * 09:32:48.913 4 August: ISAKMP: (0): former State = new State IKE_READY = IKE_I_AM1

  * 4 August 09:32:48.913: ISAKMP: (0): Beginner aggressive Mode Exchange
  * 4 August 09:32:48.913: ISAKMP: (0): 1.1.1.1 package sending 500 peer_port 500 (I) my_port AG_INIT_EXCH
  * 09:32:48.913 4 August: ISAKMP: (0): sending a packet IPv4 IKE.
  * 4 August 09:32:58.913: ISAKMP: (0): transmit phase 1 AG_INIT_EXCH...
  * 09:32:58.913 4 August: ISAKMP (0): increment the count of errors on his, try 1 5: retransmit the phase 1
  * 4 August 09:32:58.913: ISAKMP: (0): transmit phase 1 AG_INIT_EXCH
  * 4 August 09:32:58.913: ISAKMP: (0): 1.1.1.1 package sending 500 peer_port 500 (I) my_port AG_INIT_EXCH
  * 09:32:58.913 4 August: ISAKMP: (0): sending a packet IPv4 IKE.
  * 4 August 09:33:08.913: ISAKMP: (0): transmit phase 1 AG_INIT_EXCH...
  * 09:33:08.913 4 August: ISAKMP (0): increment the count of errors on his, try 2 of 5: retransmit the phase 1
  * 4 August 09:33:08.913: ISAKMP: (0): transmit phase 1 AG_INIT_EXCH
  * 4 August 09:33:08.913: ISAKMP: (0): 1.1.1.1 package sending 500 peer_port 500 (I) my_port AG_INIT_EXCH
  * 09:33:08.913 4 August: ISAKMP: (0): sending a packet IPv4 IKE.
  * 4 August 09:33:18.913: ISAKMP: (0): transmit phase 1 AG_INIT_EXCH...
  * 09:33:18.913 4 August: ISAKMP (0): increment the count of errors on his, try 3 of 5: retransmit the phase 1
  * 4 August 09:33:18.913: ISAKMP: (0): transmit phase 1 AG_INIT_EXCH
  * 4 August 09:33:18.913: ISAKMP: (0): 1.1.1.1 package sending 500 peer_port 500 (I) my_port AG_INIT_EXCH
  * 09:33:18.913 4 August: ISAKMP: (0): sending a packet IPv4 IKE.
  * 4 August 09:33:28.913: ISAKMP: (0): transmit phase 1 AG_INIT_EXCH...
  * 09:33:28.913 4 August: ISAKMP (0): increment the count of errors on his, try 4 out 5: retransmit the phase 1
  * 4 August 09:33:28.913: ISAKMP: (0): transmit phase 1 AG_INIT_EXCH
  * 4 August 09:33:28.913: ISAKMP: (0): 1.1.1.1 package sending 500 peer_port 500 (I) my_port AG_INIT_EXCH
  * 09:33:28.913 4 August: ISAKMP: (0): sending a packet IPv4 IKE.

  There is no DMVPN on the SAA. All that you have configured, is not compatible with the ASA or something another DMVPN then. At least debugging shows that there are some EzVPN involved.

  The debug version, it seems that there is no communication on UDP/500 possible between devices. Maybe something is blocking who?

• authenticate the cisco WLC 5508 with cisco ACS 1120 (version 5.0) using GANYMEDE +.

  My installation has cisco WLC 5508 and ACS 1120 ver 5.0. How to authenticate users who access to the WLC via the ACS 1120 users GANYMEDE +. I am able to authenticate users for routers and cisco switches, but when I try the same for the CMT, it fails.

  Can someone explain please the config/basic steps that must be configured on both services ACS & WLC.

  You use plain vanilla 5.0 or have installed patches?

  the ACS 5.1 has new GANYMEDE related functionaity, including support for custom services and attributes. If they are necessary for the WLC yo need support it would improve.

  He could also relevant corrective patch from calendar 5.0 but I can't find any relevant specific at this stage CDETS

• Cisco ASA IPS with enforcement

  Hi all

  I don't know if this is the best place to connect to this application, because it comes to ASA and convenient best IPS.

  In any case, I was wondering what the best approach is to integrate a Cisco IPS GOAL module in an existing configuration of Cisco ASA, which uses the default application in the world control - i.e.

  ---------------------------

  Policy-map global_policy

  class inspection_default

  inspect the preset_dns_map dns

  inspect the ftp

  etc etc.

  global service-policy global_policy

  ---------------------------

  I was keen to inspect all traffic that was OK coming from our Web-based interface in our environment, while I was trying to do something like:

  ---------------------------

  class-map ips

  corresponds to the list of internet access

  !

  ips policy-map

  class ips

  IPS inline fail-closed

  !

  global service-policy global_policy

  service-policy ips outside interface

  ---------------------------

  This configuration would allow inspection of the demand for traffic going from inside to outside, but to redirect traffic from outside within the IPS?

  Thank you

  As for the configuration. It should inspect traffic in both directions as apply you it globally, and the map-IPS policy, it would redirect internet traffic to the inside network.

• CISCO ASA 5515 WITH THE VERSION OF FIREPOWER

  ASA 5515 service with the power of fire. Can be managed with ASDM firepower. ?

  Anyone suggests Versions for firepower, ASDM, ASA?

  Kindly help

  You will find it useful to install the Module of firepower on ASA for the management of the premises:

  http://www.Cisco.com/c/en/us/TD/docs/security/ASA/Quick_Start/SFR/firepo...

  Thank you

  Guillaume

  Rate if this can help!

• The services configuration of firepower on Cisco asa 5506 with ASDM

  I have a few 5506 firewalls, and they are fully licensed with services of power, control, Protection, URL filtering, malware. I have intend running and configuration of all of this on the 5506 by ASDM. I was wondering if there are guides for a basic configuration and the implementation of policies available. Something to show a basic configuration which would technically begin inspection of traffic and work. Then I can edit and make changes to my taste.

  Thank you

  My recommendation to clients is to look at the Cisco Live, BRKSEC-2018presentation. Please refer to the 56 slide from for a good overview of how policies are installed in a module of firepower.

  There are also a number of other detailed guides available in the FireSIGHT Management Center product support page should you care to learn more about customization and operations. You can also find the series of videos of ASA FirePOWER on request to Labminutes.com useful to guide you on execution of operations of your system.

• Cisco ASA 5505 - capable to connect to VPN - access forbidden inside

  Hello

  I tried to set up a virtual private network for weeks, I can connect to the public IP address of the ASA, but I can't reach anything behind Cisco.

  I give you my config:

  ASA Version 8.2 (5)
  !
  host name asa
  sarg domain name * .net
  activate the encrypted password of Z4K16OvBr0J5Dj/2
  2KFQnbNIdI.2KYOU encrypted passwd
  names of
  !
  interface Ethernet0/0
  switchport access vlan 2
  !
  interface Ethernet0/1
  !
  interface Ethernet0/2
  !
  interface Ethernet0/3
  !
  interface Ethernet0/4
  !
  interface Ethernet0/5
  !
  interface Ethernet0/6
  !
  interface Ethernet0/7
  !
  interface Vlan1
  nameif inside
  security-level 100
  IP 192.168.1.1 255.255.255.0
  !
  interface Vlan2
  nameif outside
  security-level 0
  IP address dhcp setroute
  !
  passive FTP mode
  DNS server-group DefaultDNS
  domain sargicisco.net
  inside_nat0_outbound to access ip 192.168.1.0 scope list allow 255.255.255.0 192.168.1.0 255.255.255.0
  inside_nat0_outbound to access ip 192.168.1.0 scope list allow 255.255.255.0 192.168.254.0 255.255.255.240
  Remote_Sargi_splitTunnelAcl list standard access allowed 192.168.1.0 255.255.255.0
  sheep - in extended access-list permit ip 192.168.1.0 255.255.255.0 192.168.254.0 255.255.255.0
  pager lines 24
  asdm of logging of information
  Outside 1500 MTU
  Within 1500 MTU
  mask 192.168.254.1 - 192.168.254.10 255.255.255.0 IP local pool SAVPN_Pool
  ICMP unreachable rate-limit 1 burst-size 1
  don't allow no asdm history
  ARP timeout 14400
  Global 1 interface (outside)
  NAT (inside) 0-list of access inside_nat0_outbound
  NAT (inside) 1 0.0.0.0 0.0.0.0
  Timeout xlate 03:00
  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
  Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
  timeout tcp-proxy-reassembly 0:01:00
  Floating conn timeout 0:00:00
  dynamic-access-policy-registration DfltAccessPolicy
  Enable http server
  http 192.168.1.0 255.255.255.0 inside
  No snmp server location
  No snmp Server contact
  Server enable SNMP traps snmp authentication linkup, linkdown cold start
  Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
  Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac
  Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac
  Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac
  Crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
  Crypto ipsec transform-set ESP-AES-128-MD5-esp - aes esp-md5-hmac
  Crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
  Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac
  Crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
  Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac
  life crypto ipsec security association seconds 28800
  Crypto ipsec kilobytes of life - safety 4608000 association
  crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 pfs Group1 set
  Crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 value transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5
  outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP
  outside_map interface card crypto outside
  inside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP
  inside crypto map inside_map interface
  crypto ISAKMP allow outside
  crypto ISAKMP allow inside
  crypto ISAKMP policy 10
  preshared authentication
  3des encryption
  sha hash
  Group 2
  life 86400
  VPN-addr-assign local reuse / time 5
  Telnet timeout 5
  SSH timeout 5
  Console timeout 0
  management-access inside
  dhcpd outside auto_config
  !
  dhcpd address 192.168.1.5 - 192.168.1.36 inside
  Wis field dhcpd * .net interface inside
  dhcpd allow inside
  !

  a basic threat threat detection
  Statistics-list of access threat detection
  no statistical threat detection tcp-interception
  WebVPN
  allow outside
  allow inside
  SVC disk0:/anyconnect-win-2.5.2014-k9.pkg 1 image
  enable SVC
  tunnel-group-list activate
  attributes of Group Policy DfltGrpPolicy
  Protocol-tunnel-VPN IPSec l2tp ipsec svc webvpn
  internal Remote_Sargi group strategy
  attributes of Group Policy Remote_Sargi
  Protocol-tunnel-VPN IPSec
  Split-tunnel-policy tunnelspecified
  value of Split-tunnel-network-list Remote_Sargi_splitTunnelAcl
  sargicisco.NET value by default-field
  username kevin mz6JxJib/sQqvsw9 password encrypted privilege 0
  username kevin attributes
  VPN-group-policy DfltGrpPolicy
  type tunnel-group SAVPN remote access
  attributes global-tunnel-group SAVPN
  address pool SAVPN_Pool
  tunnel-group SAVPN webvpn-attributes
  enable SAVPN group-alias
  allow group-url https://82.228.XXX.XXX/SAVPN
  type tunnel-group Remote_Sargi remote access
  attributes global-tunnel-group Remote_Sargi
  address pool SAVPN_Pool
  Group Policy - by default-Remote_Sargi
  IPSec-attributes tunnel-group Remote_Sargi
  pre-shared key *.
  !
  class-map inspection_default
  match default-inspection-traffic
  !
  !
  type of policy-card inspect dns preset_dns_map
  parameters
  maximum message length automatic of customer
  message-length maximum 512
  Policy-map global_policy
  class inspection_default
  inspect the preset_dns_map dns
  inspect the ftp
  inspect h323 h225
  inspect the h323 ras
  inspect the rsh
  inspect the rtsp
  inspect esmtp
  inspect sqlnet
  inspect the skinny
  inspect sunrpc
  inspect xdmcp
  inspect the sip
  inspect the netbios
  inspect the tftp
  Review the ip options
  !
  global service-policy global_policy
  context of prompt hostname
  no remote anonymous reporting call
  Cryptochecksum:387a6e260247a545f4df0d3f28ba58c5
  : end

  Thank you

  Hello

  Could you remove this statement and add the last:

  no nat (inside) 0-list of access inside_nat0_outbound

  ADD: nat (inside) 0 access-list sheep - in

  Kind regards

  Aditya

  Please evaluate the useful messages and mark the correct answers.

• Cisco ASA 8.0.4 AnyConnect works do not with Vista and IE7

  Hello

  I currently have a Cisco ASA 5520 with the latest version of the Software ASA/AMPS/Anyconnect. However I can't get Vista and IE7 to connect using the free client anyconnect VPN error message following appears

  "Setup could not start the Cisco VPN Client".

  Is there a workaround for this.

  Thanks in advance

  Eoin

  I'm glad you got it working :)

  Please evaluate the positions if find you them useful.

  Concerning

  Farrukh

• enabling remote vpn Cisco asa

  Dear team,

  I have a Cisco asa firewall, I would enable remote vpn (ssl vpn or customer).

  Please check the joint view version and suggest which are missing or need to enable them.

  Therefore, I will obtain concrete results and enable VPN.

  concerning

  SecIT

  With the license and the software version you have, you can only run the existing IPsec VPN client.

  To run AnyConnect SSL VPN client-based, you must acquire a license AnyConnect Essentials. For your platform that would be L-ASA-AC-E -5550=. (Clientless SSL VPN would be a different reference number.)

  I also suggest upgrading your system beyond 8.2 software (2) the current recommended release would be 9.0 (3). (9.1 (5) is the last on the 5550.)

• Cisco ASA 5510 multiple dynamic config VPN L2L necessary

  Hello

  We have a Cisco asa 5510 with static IP address. Also, we have a remote office with a dynamic IP address. We now have a dynamic to static VPN configured L2L. And now, we must add new tunnel to another site with a dynamic IP address. Is this possible? Does anyone have an example of woking, or manual?

  Oleg Kobelev

  The config only you need in the ASA is: -.

  (1) set of crypto processing

  (2) political ISAKMP

  (3) dynamic Crypto map

  (4) default group L2L & PSK

  (5) Config RRI (reverse Route Injection)

  HTH >

• Is supported PPTP vpn cisco ASA 5520 firewall?

  Hi all

  I'm Md.kamruzzaman. My compnay buy a firewall of cisco asa 5520 and I want to configure PPTP vpn on asa 5520 firewall. Is it possible to configure the PPTP vpn to asa firewall. If possible can you please tell me what is the procedure to configure the PPTP vpn.

  Best regards

  MD.kamruzzaman

  Sorry, but the Cisco ASA firewall does not support PPTP VPN termination.

  You may terminate IPSec and SSL VPN but not of type PPTP.

  If you are new to the ASA, how best to configure the supported VPN types is via the VPN Wizard integrated into the application of management of ASSISTANT Deputy Ministers.

• ASA static IP Addressing for IPSec VPN Client

  Hello guys.

  I use a Cisco ASA 5540 with version 8.4.
  I need to assign a static IP address to a VPN client. I saw in the documentation Cisco that this can be done to validate the user against the local ASA and in the user account database, you assign a dedicated IP address, or using the vpn-framed-ip-address CLI command.
  The problem is that the customer never gets this address and it always gets one of the pool in the political group. If I delete this pool, the client can't get any address.
  No idea on how to fix this or how can I give this static IP address to a specific VPN client?
  Thank you.

  Your welcome please check the response as correct and mark.

  See you soon

• Cisco ASA 5505 unable to access the remote network

  Hello

  I have a Cisco ASA 5505, with 50 basic license, which is connected directly to the Modem cable with a public IP address. I have configured and active VPN on the outside interface. When connect us, we connect well without error, but we are not able to access all the resources on the remote network.

  ASA IOS version 8.2 (5)

  Remote IP network: 10.0.0.0/24

  VPN IP Pool: 192.168.102.10 - 25

  I have attached the config: llc.txt

  Please let me know if you have any questions.

  Thank you!

  Hello

  Try adding NAT 0 because inside subnet--> subnet distance

  NAT (inside) 0 access-list TEST

  TEST access ip 10.0.0.0 scope list allow 255.255.255.0 192.168.102.10 255.255.255.224

  HTH

  MS