Cisco ASA 5510 VPN Site to Site with Sonicwall
I am trying to configure a tunnel between a Cisco ASA 5510 VPN (Version 8.2 (2)) and TZ200 Sonicwall. I rose tunnel and go and I am able to ping the internal IP address of Cisco ASA of the Sonicwall LAN but nothing work. When I try to ping a host behind the Cisco ASA of the Sonicwall LAN I get the following message "rules asymmetrical NAT matched for flows forward and backward; Connection for tcp src outside:10.20.10.x/xxxx dst inside:10.20.2.x/xxxx refused due to failure of reverse path of NAT"on the SAA
Googling the error above shows the problems with version 8.3 or later that resembled the nat commands have been changed SAA, train is still on 8.2 but I another common question does not add an exemption of NAT I have double-triple checked that I did add an exception rule of NAT of the hosts on the network from cisco for the guests of the Sonicwall network. Looks like I hit a road block so any help would be appreciated. Thank you
Here are a few excertps of the config file (10.20.2.0 behind the cisco) and 10.20.10.0 behind the sonicwall
NAT (inside) 0 access-list sheep
..
IP 10.20.2.0 allow Access-list extended sheep 255.255.255.0 10.20.10.0 255.255.255.0
access extensive list ip 10.20.2.0 outside_1_cryptomap allow 255.255.255.0 10.20.10.0 255.255.255.0
..
card crypto outside_map 1 match address outside_1_cryptomap
card crypto outside_map 1 set counterpart x.x.x.x
card crypto outside_map 1 set of transformation-ESP-3DES-SHA
outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP
outside_map interface card crypto outside
..
crypto ISAKMP allow outside
crypto ISAKMP policy 5
preshared authentication
3des encryption
sha hash
Group 2
lifetime 28800
..
internal SiteToSitePolicy group strategy
attributes of Group Policy SiteToSitePolicy
VPN-idle-timeout no
Protocol-tunnel-VPN IPSec
Split-tunnel-network-list no
..
tunnel-group x.x.x.x type ipsec-l2l
tunnel-group x.x.x.x General attributes
Group Policy - by default-SiteToSitePolicy
tunnel-group ipsec-attributes x.x.x.x
pre-shared key *.
..
Added some excerpts from the configuration file
Hello Manjitriat,
Okay, detected IPSEC parody is normal, that means you are trying to send unencrypted on a line of encrypted packets.
Now, if you see on the plotter of package that traffic will hollow the VPN channel all its fine in your site.
Now the packet tracer must be something like this:
entrance to Packet-trace inside private_ip_lan destination_private_ip_lan 1025 tcp 80
Please provide us with the result of the following instructions after you run the packet tracer.
See the crypto Isakamp SA
See the crypto Ipsec SA
Kind regards
Julio
Tags: Cisco Security
Similar Questions
-
Cisco ASA 5505 VPN Site to Site
Hi all
First post on the forums. I have worked with Cisco ASA 5505 for a few months and I recently bought a 2nd ASA to implement tunnel VPN Site to Site. It seems so simple in the number of videos watched on the internet. But when I did he surprise it did work for me... I've removed the tunnels, a number of times and tried to recreate. I use the VPN Wizard in the SMA to create the tunnel. Both the asa 5505 of are and have the same firmware even etc..
I'd appreciate any help that can be directed to this problem please. Slowly losing my mind
Please see details below:
Two ADMS are 7.1
IOS
ASA 1
Nadia
:
ASA Version 9.0 (1)
!
hostname PAYBACK
activate the encrypted password of HSMurh79NVmatjY0
volatile xlate deny tcp any4 any4
volatile xlate deny tcp any4 any6
volatile xlate deny tcp any6 any4
volatile xlate deny tcp any6 any6
volatile xlate deny udp any4 any4 eq field
volatile xlate deny udp any4 any6 eq field
volatile xlate deny udp any6 any4 eq field
volatile xlate deny udp any6 any6 eq field
2KFQnbNIdI.2KYOU encrypted passwd
names of
local pool VPN1 192.168.50.1 - 192.168.50.254 255.255.255.0 IP mask
!
interface Ethernet0/0
switchport access vlan 2
Speed 100
full duplex
!
interface Ethernet0/1
link Trunk Description of SW1
switchport trunk allowed vlan 1,10,20,30,40
switchport trunk vlan 1 native
switchport mode trunk
!
interface Ethernet0/2
!
interface Ethernet0/3
!
interface Ethernet0/4
!
interface Ethernet0/5
!
interface Ethernet0/6
!
interface Ethernet0/7
!
interface Vlan1
No nameif
no level of security
no ip address
!
interface Vlan2
nameif outside
security-level 0
IP 92.51.193.158 255.255.255.252
!
interface Vlan10
nameif inside
security-level 100
IP 192.168.10.1 255.255.255.0
!
interface Vlan20
nameif servers
security-level 100
address 192.168.20.1 255.255.255.0
!
Vlan30 interface
nameif printers
security-level 100
192.168.30.1 IP address 255.255.255.0
!
interface Vlan40
nameif wireless
security-level 100
192.168.40.1 IP address 255.255.255.0
!
connection line banner welcome to the Payback loyalty systems
boot system Disk0: / asa901 - k8.bin
passive FTP mode
summer time clock GMT/IDT recurring last Sun Mar 01:00 last Sun Oct 02:00
DNS domain-lookup outside
DNS lookup field inside
domain-lookup DNS servers
DNS lookup domain printers
DNS domain-lookup wireless
DNS server-group DefaultDNS
Server name 83.147.160.2
Server name 83.147.160.130
permit same-security-traffic inter-interface
network obj_any object
subnet 0.0.0.0 0.0.0.0
ftp_server network object
network of the Internal_Report_Server object
Home 192.168.20.21
Description address internal automated report server
network of the Report_Server object
Home 89.234.126.9
Description of server automated reports
service object RDP
service destination tcp 3389 eq
Description RDP to the server
network of the Host_QA_Server object
Home 89.234.126.10
Description QA host external address
network of the Internal_Host_QA object
Home 192.168.20.22
host of computer virtual Description for QA
network of the Internal_QA_Web_Server object
Home 192.168.20.23
Description Web Server in the QA environment
network of the Web_Server_QA_VM object
Home 89.234.126.11
Server Web Description in the QA environment
service object SQL_Server
destination eq 1433 tcp service
network of the Demo_Server object
Home 89.234.126.12
Description server set up for the product demo
network of the Internal_Demo_Server object
Home 192.168.20.24
Internal description of the demo server IP address
network of the NETWORK_OBJ_192.168.20.0_24 object
subnet 192.168.20.0 255.255.255.0
network of the NETWORK_OBJ_192.168.50.0_26 object
255.255.255.192 subnet 192.168.50.0
network of the NETWORK_OBJ_192.168.0.0_16 object
Subnet 192.168.0.0 255.255.0.0
service object MSSQL
destination eq 1434 tcp service
MSSQL port description
VPN network object
192.168.50.0 subnet 255.255.255.0
network of the NETWORK_OBJ_192.168.50.0_24 object
192.168.50.0 subnet 255.255.255.0
service object TS
tcp destination eq 4400 service
service of the TS_Return object
tcp source eq 4400 service
network of the External_QA_3 object
Home 89.234.126.13
network of the Internal_QA_3 object
Home 192.168.20.25
network of the Dev_WebServer object
Home 192.168.20.27
network of the External_Dev_Web object
Home 89.234.126.14
network of the CIX_Subnet object
255.255.255.0 subnet 192.168.100.0
network of the NETWORK_OBJ_192.168.10.0_24 object
192.168.10.0 subnet 255.255.255.0
network of the NETWORK_OBJ_84.39.233.50 object
Home 84.39.233.50
network of the NETWORK_OBJ_92.51.193.158 object
Home 92.51.193.158
network of the NETWORK_OBJ_192.168.100.0_24 object
255.255.255.0 subnet 192.168.100.0
network of the NETWORK_OBJ_192.168.1.0_24 object
subnet 192.168.1.0 255.255.255.0
object-group service DM_INLINE_SERVICE_1
the tcp destination eq ftp service object
the purpose of the tcp destination eq netbios-ssn service
the purpose of the tcp destination eq smtp service
service-object TS
the Payback_Internal object-group network
object-network 192.168.10.0 255.255.255.0
object-network 192.168.20.0 255.255.255.0
object-network 192.168.40.0 255.255.255.0
object-group service DM_INLINE_SERVICE_3
the purpose of the service tcp destination eq www
the purpose of the tcp destination eq https service
service-object TS
service-object, object TS_Return
object-group service DM_INLINE_SERVICE_4
service-object RDP
the purpose of the service tcp destination eq www
the purpose of the tcp destination eq https service
object-group service DM_INLINE_SERVICE_5
purpose purpose of the MSSQL service
service-object RDP
service-object TS
object-group Protocol TCPUDP
object-protocol udp
object-tcp protocol
object-group service DM_INLINE_SERVICE_6
service-object TS
service-object, object TS_Return
the purpose of the service tcp destination eq www
the purpose of the tcp destination eq https service
Note to outside_access_in to access list that this rule allows Internet the interal server.
Notice on the outside_access_in of the access-list allowed:
Comment from outside_access_in-list of FTP access
Comment from outside_access_in-RDP access list
Comment from outside_access_in-list of SMTP access
Note to outside_access_in to access list Net Bios
Comment from outside_access_in-SQL access list
Comment from outside_access_in-list to access TS - 4400
outside_access_in list extended access allowed object object-group DM_INLINE_SERVICE_1 any4 Internal_Report_Server
access host access-list outside_access_in note rule internal QA
Notice on the outside_access_in of the access-list allowed:
Comment from outside_access_in-HTTP access list
Comment from outside_access_in-RDP access list
outside_access_in list extended access permitted tcp any4 object Internal_Host_QA eq www
Notice on the outside_access_in of the access-list access to the internal Web server:
Notice on the outside_access_in of the access-list allowed:
Comment from outside_access_in-HTTP access list
Comment from outside_access_in-RDP access list
outside_access_in list extended access allowed object object-group DM_INLINE_SERVICE_3 any4 Internal_QA_Web_Server
Note to outside_access_in to access list rule allowing access to the demo server
Notice on the outside_access_in of the access-list allowed:
Comment from outside_access_in-RDP access list
Comment from outside_access_in-list to access MSSQL
outside_access_in list extended access allowed object object-group DM_INLINE_SERVICE_4 any4 Internal_Demo_Server
outside_access_in list extended access allowed object-group DM_INLINE_SERVICE_5 any object Internal_QA_3
Note to outside_access_in access to the development Web server access list
outside_access_in list extended access allowed object-group DM_INLINE_SERVICE_6 any object Dev_WebServer
AnyConnect_Client_Local_Print deny any4 any4 ip extended access list
AnyConnect_Client_Local_Print list extended access permitted tcp any4 any4 eq lpd
Note AnyConnect_Client_Local_Print of access list IPP: Internet Printing Protocol
AnyConnect_Client_Local_Print list extended access permitted tcp any4 any4 eq 631
print the access-list AnyConnect_Client_Local_Print Note Windows port
AnyConnect_Client_Local_Print list extended access permitted tcp any4 any4 eq 9100
access-list AnyConnect_Client_Local_Print mDNS Note: multicast DNS protocol
AnyConnect_Client_Local_Print list extended access permit udp host 224.0.0.251 any4 eq 5353
AnyConnect_Client_Local_Print of access list LLMNR Note: link Local Multicast Name Resolution protocol
AnyConnect_Client_Local_Print list extended access permit udp host 224.0.0.252 any4 eq 5355
Note access list TCP/NetBIOS protocol AnyConnect_Client_Local_Print
AnyConnect_Client_Local_Print list extended access permitted tcp any4 any4 EQ. 137
AnyConnect_Client_Local_Print list extended access permitted udp any4 any4 eq netbios-ns
Payback_VPN_splitTunnelAcl list standard access allowed 192.168.20.0 255.255.255.0
permit outside_cryptomap to access extended list ip 192.168.10.0 255.255.255.0 192.168.100.0 255.255.255.0
pager lines 24
Enable logging
information recording console
asdm of logging of information
address record
the journaling recipient
level alerts
Outside 1500 MTU
Within 1500 MTU
MTU 1500 servers
MTU 1500 printers
MTU 1500 wireless
no failover
ICMP unreachable rate-limit 1 burst-size 1
ASDM image disk0: / asdm-711 - 52.bin
don't allow no asdm history
ARP timeout 14400
no permit-nonconnected arp
NAT (inside, outside) source Dynamics one interface
NAT (wireless, outdoors) source Dynamics one interface
NAT (servers, outside) no matter what source dynamic interface
NAT (servers, external) static source Internal_Report_Server Report_Server
NAT (servers, external) static source Internal_Host_QA Host_QA_Server
NAT (servers, external) static source Internal_QA_Web_Server Web_Server_QA_VM
NAT (servers, external) static source Internal_Demo_Server Demo_Server
NAT (servers, external) static source NETWORK_OBJ_192.168.20.0_24 NETWORK_OBJ_192.168.20.0_24 NETWORK_OBJ_192.168.50.0_24 NETWORK_OBJ_192.168.50.0_24 non-proxy-arp-search of route static destination
NAT (servers, external) static source Internal_QA_3 External_QA_3
NAT (servers, external) static source Dev_WebServer External_Dev_Web
NAT (inside, outside) static source NETWORK_OBJ_192.168.10.0_24 NETWORK_OBJ_192.168.10.0_24 NETWORK_OBJ_192.168.1.0_24 NETWORK_OBJ_192.168.1.0_24 non-proxy-arp-search of route static destination
NAT (inside, outside) static source NETWORK_OBJ_192.168.10.0_24 NETWORK_OBJ_192.168.10.0_24 NETWORK_OBJ_192.168.100.0_24 NETWORK_OBJ_192.168.100.0_24 non-proxy-arp-search of route static destination
Access-group outside_access_in in interface outside
Route outside 0.0.0.0 0.0.0.0 92.51.193.157 1
Timeout xlate 03:00
Pat-xlate timeout 0:00:30
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
Floating conn timeout 0:00:00
dynamic-access-policy-registration DfltAccessPolicy
identity of the user by default-domain LOCAL
the ssh LOCAL console AAA authentication
Enable http server
http 192.168.10.0 255.255.255.0 inside
http 192.168.40.0 255.255.255.0 wireless
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown cold start
Crypto ipsec transform-set ikev1 ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-DES-SHA esp - esp-sha-hmac
Crypto ipsec transform-set ikev1 esp ESP-DES-MD5-esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-3DES-MD5-esp-3des esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-128-SHA aes - esp esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-esp - aes esp-md5-hmac
Crypto ipsec transform-set ikev1 SHA-ESP-3DES esp-3des esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-128-SHA-TRANS-aes - esp esp-sha-hmac
Crypto ipsec ikev1 transform-set ESP-AES-128-SHA-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-TRANS-aes - esp esp-md5-hmac
Crypto ipsec ikev1 transform-set ESP-AES-128-MD5-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-AES-192-SHA-TRANS esp-aes-192 esp-sha-hmac
Crypto ipsec ikev1 transform-set ESP-AES-192-SHA-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-AES-192-MD5-TRANS esp-aes-192 esp-md5-hmac
Crypto ipsec ikev1 transform-set ESP-AES-192-MD5-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-AES-256-SHA-TRANS esp-aes-256 esp-sha-hmac
Crypto ipsec ikev1 transform-set ESP-AES-256-SHA-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-AES-256-MD5-TRANS esp-aes-256 esp-md5-hmac
Crypto ipsec ikev1 transform-set ESP-AES-256-MD5-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-3DES-SHA-TRANS esp-3des esp-sha-hmac
Crypto ipsec ikev1 transform-set ESP-3DES-SHA-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-3DES-MD5-TRANS esp-3des esp-md5-hmac
Crypto ipsec ikev1 transform-set ESP-3DES-MD5-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-DES-SHA-TRANS esp - esp-sha-hmac
Crypto ipsec ikev1 transform-set ESP-DES-SHA-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-DES-MD5-TRANS esp - esp-md5-hmac
Crypto ipsec ikev1 transform-set ESP-DES-MD5-TRANS mode transit
Crypto ipsec ikev2 AES256 ipsec-proposal
Protocol esp encryption aes-256
Esp integrity sha - 1, md5 Protocol
Crypto ipsec ikev2 ipsec-proposal AES192
Protocol esp encryption aes-192
Esp integrity sha - 1, md5 Protocol
Crypto ipsec ikev2 ipsec-proposal AES
Esp aes encryption protocol
Esp integrity sha - 1, md5 Protocol
Crypto ipsec ikev2 proposal ipsec 3DES
Esp 3des encryption protocol
Esp integrity sha - 1, md5 Protocol
Crypto ipsec ikev2 ipsec-proposal OF
encryption protocol esp
Esp integrity sha - 1, md5 Protocol
Crypto ipsec pmtu aging infinite - the security association
card crypto outside_map 1 match address outside_cryptomap
card crypto outside_map 1 set pfs
peer set card crypto outside_map 1 84.39.233.50
card crypto outside_map 1 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5
outside_map card crypto 1 set ikev2 AES256 AES192 AES 3DES ipsec-proposal OF
outside_map interface card crypto outside
trustpool crypto ca policy
IKEv2 crypto policy 1
aes-256 encryption
integrity sha
Group 5
FRP sha
second life 86400
IKEv2 crypto policy 10
aes-192 encryption
integrity sha
Group 5
FRP sha
second life 86400
IKEv2 crypto policy 20
aes encryption
integrity sha
Group 5
FRP sha
second life 86400
IKEv2 crypto policy 30
3des encryption
integrity sha
Group 5
FRP sha
second life 86400
IKEv2 crypto policy 40
the Encryption
integrity sha
Group 5
FRP sha
second life 86400
Crypto ikev2 activate out of service the customer port 443
Crypto ikev1 allow outside
IKEv1 crypto policy 10
preshared authentication
3des encryption
sha hash
Group 2
life 86400
Telnet timeout 5
SSH 77.75.100.208 255.255.255.240 outside
SSH 192.168.10.0 255.255.255.0 inside
SSH 192.168.40.0 255.255.255.0 wireless
SSH timeout 5
Console timeout 0dhcpd 192.168.0.1 dns
dhcpd outside auto_config
!
dhcpd address 192.168.10.21 - 192.168.10.240 inside
dhcpd dns 192.168.20.21 83.147.160.2 interface inside
paybackloyalty.com dhcpd option 15 inside ascii interface
dhcpd allow inside
!
dhcpd address 192.168.40.21 - 192.168.40.240 Wireless
dhcpd dns 192.168.20.21 83.147.160.2 wireless interface
dhcpd update dns of the wireless interface
dhcpd option 15 ascii paybackloyalty.com wireless interface
dhcpd activate wireless
!
a basic threat threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
internal Payback_VPN group strategy
attributes of Group Policy Payback_VPN
VPN - 10 concurrent connections
Ikev1 VPN-tunnel-Protocol
Split-tunnel-policy tunnelspecified
value of Split-tunnel-network-list Payback_VPN_splitTunnelAcl
attributes of Group Policy DfltGrpPolicy
value of 83.147.160.2 DNS server 83.147.160.130
VPN-tunnel-Protocol ikev1, ikev2 clientless ssl
internal GroupPolicy_84.39.233.50 group strategy
attributes of Group Policy GroupPolicy_84.39.233.50
VPN-tunnel-Protocol ikev1, ikev2
Noelle XB/IpvYaATP.2QYm username encrypted password
Noelle username attributes
VPN-group-policy Payback_VPN
type of remote access service
username Éanna encrypted password privilege 0 vXILR9ZZQIsd1Naw
Éanna attributes username
VPN-group-policy Payback_VPN
type of remote access service
Michael qpbleUqUEchRrgQX of encrypted password username
user name Michael attributes
VPN-group-policy Payback_VPN
type of remote access service
username, password from Danny .7fEXdzESUk6S/cC encrypted privilege 0
user name Danny attributes
VPN-group-policy Payback_VPN
type of remote access service
Aileen tytrelqvV5VRX2pz encrypted password privilege 0 username
user name Aileen attributes
VPN-group-policy Payback_VPN
type of remote access service
Aidan aDu6YH0V5XaxpEPg encrypted password privilege 0 username
Aidan username attributes
VPN-group-policy Payback_VPN
type of remote access service
username password 6e6Djaz3W/XH59zX gordon encrypted privilege 15
shane.c iqGMoWOnfO6YKXbw encrypted password username
username shane.c attributes
VPN-group-policy Payback_VPN
type of remote access service
Shane uYePLcrFadO9pBZx of encrypted password username
user name Shane attributes
VPN-group-policy Payback_VPN
type of remote access service
username, encrypted James TdYPv1pvld/hPM0d password
user name James attributes
VPN-group-policy Payback_VPN
type of remote access service
Mark yruxpddqfyNb.qFn of encrypted password username
user name brand attributes
type of service admin
username password of Mary XND5FTEiyu1L1zFD encrypted
user name Mary attributes
VPN-group-policy Payback_VPN
type of remote access service
Massimo vs65MMo4rM0l4rVu encrypted password privilege 0 username
Massimo username attributes
VPN-group-policy Payback_VPN
type of remote access service
type tunnel-group Payback_VPN remote access
attributes global-tunnel-group Payback_VPN
VPN1 address pool
Group Policy - by default-Payback_VPN
IPSec-attributes tunnel-group Payback_VPN
IKEv1 pre-shared-key *.
tunnel-group 84.39.233.50 type ipsec-l2l
tunnel-group 84.39.233.50 General-attributes
Group - default policy - GroupPolicy_84.39.233.50
IPSec-attributes tunnel-group 84.39.233.50
IKEv1 pre-shared-key *.
remote control-IKEv2 pre-shared-key authentication *.
pre-shared-key authentication local IKEv2 *.
!
Global class-card class
match default-inspection-traffic
!
!
World-Policy policy-map
Global category
inspect the dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
Review the ip options
inspect the netbios
inspect the pptp
inspect the rsh
inspect the rtsp
inspect the sip
inspect the snmp
inspect sqlnet
inspect sunrpc
inspect the tftp
inspect xdmcp
inspect the icmp error
inspect the icmp
!
service-policy-international policy global
192.168.20.21 SMTP server
context of prompt hostname
no remote anonymous reporting call
call-home
Profile of CiscoTAC-1
no active account
http https://tools.cisco.com/its/service/oddce/services/DDCEService destination address
email address of destination [email protected] / * /
destination-mode http transport
Subscribe to alert-group diagnosis
Subscribe to alert-group environment
Subscribe to alert-group monthly periodic inventory
monthly periodicals to subscribe to alert-group configuration
daily periodic subscribe to alert-group telemetry
Cryptochecksum:d06974501eb0327a5ed229c8445f4fe1ASA 2
ASA Version 9.0 (1)
!
Payback-CIX hostname
activate the encrypted password of HSMurh79NVmatjY0
2KFQnbNIdI.2KYOU encrypted passwd
names of
!
interface Ethernet0/0
switchport access vlan 2
Speed 100
full duplex
!
interface Ethernet0/1
Description this port connects to the local network VIRTUAL 100
switchport access vlan 100
!
interface Ethernet0/2
!
interface Ethernet0/3
switchport access vlan 100
!
interface Ethernet0/4
switchport access vlan 100
!
interface Ethernet0/5
switchport access vlan 100
!
interface Ethernet0/6
switchport access vlan 100
!
interface Ethernet0/7
switchport access vlan 100
!
interface Vlan2
nameif outside
security-level 0
IP 84.39.233.50 255.255.255.240
!
interface Vlan100
nameif inside
security-level 100
IP 192.168.100.1 address 255.255.255.0
!
banner welcome to Payback loyalty - CIX connection line
passive FTP mode
summer time clock gmt/idt recurring last Sun Mar 01:00 last Sun Oct 02:00
DNS domain-lookup outside
DNS lookup field inside
DNS server-group defaultDNS
Name-Server 8.8.8.8
Server name 8.8.4.4
permit same-security-traffic inter-interface
network obj_any object
subnet 0.0.0.0 0.0.0.0
network of the host-CIX-1 object
host 192.168.100.2
Description This is the VM server host machine
network object host-External_CIX-1
Home 84.39.233.51
Description This is the external IP address of the server the server VM host
service object RDP
source between 1-65535 destination eq 3389 tcp service
network of the Payback_Office object
Home 92.51.193.158
service object MSQL
destination eq 1433 tcp service
network of the Development_OLTP object
Home 192.168.100.10
Description for Eiresoft VM
network of the External_Development_OLTP object
Home 84.39.233.52
Description This is the external IP address for the virtual machine for Eiresoft
network of the Eiresoft object
Home 146.66.160.70
Contractor s/n description
network of the External_TMC_Web object
Home 84.39.233.53
Description Public address to the TMC Web server
network of the TMC_Webserver object
Home 192.168.100.19
Internal description address TMC Webserver
network of the External_TMC_OLTP object
Home 84.39.233.54
External targets OLTP IP description
network of the TMC_OLTP object
Home 192.168.100.18
description of the interal target IP address
network of the External_OLTP_Failover object
Home 84.39.233.55
IP failover of the OLTP Public description
network of the OLTP_Failover object
Home 192.168.100.60
Server failover OLTP description
network of the servers object
subnet 192.168.20.0 255.255.255.0
being Wired network
192.168.10.0 subnet 255.255.255.0
the subject wireless network
192.168.40.0 subnet 255.255.255.0
network of the NETWORK_OBJ_192.168.100.0_24 object
255.255.255.0 subnet 192.168.100.0
network of the NETWORK_OBJ_192.168.10.0_24 object
192.168.10.0 subnet 255.255.255.0
network of the Eiresoft_2nd object
Home 137.117.217.29
Description 2nd Eiresoft IP
network of the Dev_Test_Webserver object
Home 192.168.100.12
Description address internal to the Test Server Web Dev
network of the External_Dev_Test_Webserver object
Home 84.39.233.56
Description This is the PB Dev Test Webserver
network of the NETWORK_OBJ_192.168.1.0_24 object
subnet 192.168.1.0 255.255.255.0
object-group service DM_INLINE_SERVICE_1
service-object MSQL
service-object RDP
object-group service DM_INLINE_SERVICE_2
service-object MSQL
service-object RDP
object-group service DM_INLINE_SERVICE_3
service-object MSQL
service-object RDP
object-group service DM_INLINE_SERVICE_4
service-object MSQL
service-object RDP
the tcp destination eq ftp service object
object-group service DM_INLINE_SERVICE_5
service-object MSQL
service-object RDP
the tcp destination eq ftp service object
object-group service DM_INLINE_SERVICE_6
service-object MSQL
service-object RDP
the Payback_Intrernal object-group network
object-network servers
Wired network-object
wireless network object
object-group service DM_INLINE_SERVICE_7
service-object MSQL
service-object RDP
object-group service DM_INLINE_SERVICE_8
service-object MSQL
service-object RDP
object-group service DM_INLINE_SERVICE_9
service-object MSQL
service-object RDP
object-group service DM_INLINE_SERVICE_10
service-object MSQL
service-object RDP
the tcp destination eq ftp service object
object-group service DM_INLINE_SERVICE_11
service-object RDP
the tcp destination eq ftp service object
outside_access_in list extended access allow object-group DM_INLINE_SERVICE_1 object Payback_Office object CIX-host-1
Note to access list OLTP Development Office of recovery outside_access_in
outside_access_in list extended access allow DM_INLINE_SERVICE_2 object Payback_Office object Development_OLTP object-group
Comment from outside_access_in-access Eiresoft access list
outside_access_in list extended access allow DM_INLINE_SERVICE_3 object Eiresoft object Development_OLTP object-group
outside_access_in list extended access allow DM_INLINE_SERVICE_4 object Payback_Office object TMC_Webserver object-group
Note to outside_access_in access to OLTP for target recovery Office Access list
outside_access_in list extended access allow DM_INLINE_SERVICE_5 object Payback_Office object TMC_OLTP object-group
outside_access_in list extended access allow DM_INLINE_SERVICE_6 object Payback_Office object OLTP_Failover object-group
Note to outside_access_in access-list that's allowing access of the Eiresoft on the failover OLTP server
outside_access_in list extended access allow DM_INLINE_SERVICE_7 object Eiresoft object OLTP_Failover object-group
Comment from outside_access_in-access list access for the 2nd period of INVESTIGATION of Eiresoft
outside_access_in list extended access allow DM_INLINE_SERVICE_8 object Eiresoft_2nd object Development_OLTP object-group
Note to outside_access_in access from the 2nd IP Eiresoft access list
outside_access_in list extended access allow DM_INLINE_SERVICE_9 object Eiresoft_2nd object OLTP_Failover object-group
outside_access_in list extended access allow DM_INLINE_SERVICE_10 object Payback_Office object Dev_Test_Webserver object-group
outside_access_in list extended access allow DM_INLINE_SERVICE_11 object Payback_Office object External_TMC_OLTP object-group
outside_cryptomap to access extended list ip 192.168.100.0 allow 255.255.255.0 192.168.10.0 255.255.255.0
pager lines 24
Enable logging
asdm of logging of information
Outside 1500 MTU
Within 1500 MTU
ICMP unreachable rate-limit 1 burst-size 1
don't allow no asdm history
ARP timeout 14400
no permit-nonconnected arp
NAT (inside, outside) source Dynamics one interface
NAT (inside, outside) static source CIX-host-1 External_CIX-host-1
NAT (inside, outside) static source Development_OLTP External_Development_OLTP
NAT (inside, outside) static source TMC_Webserver External_TMC_Web
NAT (inside, outside) static source TMC_OLTP External_TMC_OLTP
NAT (inside, outside) static source OLTP_Failover External_OLTP_Failover
NAT (inside, outside) static source Dev_Test_Webserver External_Dev_Test_Webserver
NAT (inside, outside) static source NETWORK_OBJ_192.168.100.0_24 NETWORK_OBJ_192.168.100.0_24 NETWORK_OBJ_192.168.10.0_24 NETWORK_OBJ_192.168.10.0_24 non-proxy-arp-search of route static destination
NAT (inside, outside) static source NETWORK_OBJ_192.168.100.0_24 NETWORK_OBJ_192.168.100.0_24 NETWORK_OBJ_192.168.1.0_24 NETWORK_OBJ_192.168.1.0_24 non-proxy-arp-search of route static destination
Access-group outside_access_in in interface outside
Route outside 0.0.0.0 0.0.0.0 84.39.233.49 1
Timeout xlate 03:00
Pat-xlate timeout 0:00:30
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
Floating conn timeout 0:00:00
dynamic-access-policy-registration DfltAccessPolicy
identity of the user by default-domain LOCAL
the ssh LOCAL console AAA authentication
Enable http server
http 92.51.193.156 255.255.255.252 outside
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown warmstart of cold start
Crypto ipsec transform-set ikev1 ESP-AES-128-SHA aes - esp esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-esp - aes esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-AES-128-SHA-TRANS-aes - esp esp-sha-hmac
Crypto ipsec ikev1 transform-set ESP-AES-128-SHA-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-TRANS-aes - esp esp-md5-hmac
Crypto ipsec ikev1 transform-set ESP-AES-128-MD5-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-AES-192-SHA-TRANS esp-aes-192 esp-sha-hmac
Crypto ipsec ikev1 transform-set ESP-AES-192-SHA-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-AES-192-MD5-TRANS esp-aes-192 esp-md5-hmac
Crypto ipsec ikev1 transform-set ESP-AES-192-MD5-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-AES-256-SHA-TRANS esp-aes-256 esp-sha-hmac
Crypto ipsec ikev1 transform-set ESP-AES-256-SHA-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-AES-256-MD5-TRANS esp-aes-256 esp-md5-hmac
Crypto ipsec ikev1 transform-set ESP-AES-256-MD5-TRANS mode transit
Crypto ipsec transform-set ikev1 SHA-ESP-3DES esp-3des esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-3DES-MD5-esp-3des esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-3DES-SHA-TRANS esp-3des esp-sha-hmac
Crypto ipsec ikev1 transform-set ESP-3DES-SHA-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-3DES-MD5-TRANS esp-3des esp-md5-hmac
Crypto ipsec ikev1 transform-set ESP-3DES-MD5-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-DES-SHA esp - esp-sha-hmac
Crypto ipsec transform-set ikev1 esp ESP-DES-MD5-esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-DES-SHA-TRANS esp - esp-sha-hmac
Crypto ipsec ikev1 transform-set ESP-DES-SHA-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-DES-MD5-TRANS esp - esp-md5-hmac
Crypto ipsec ikev1 transform-set ESP-DES-MD5-TRANS mode transit
Crypto ipsec ikev2 ipsec-proposal OF
encryption protocol esp
Esp integrity sha - 1, md5 Protocol
Crypto ipsec ikev2 proposal ipsec 3DES
Esp 3des encryption protocol
Esp integrity sha - 1, md5 Protocol
Crypto ipsec ikev2 ipsec-proposal AES
Esp aes encryption protocol
Esp integrity sha - 1, md5 Protocol
Crypto ipsec ikev2 ipsec-proposal AES192
Protocol esp encryption aes-192
Esp integrity sha - 1, md5 Protocol
Crypto ipsec ikev2 AES256 ipsec-proposal
Protocol esp encryption aes-256
Esp integrity sha - 1, md5 Protocol
Crypto ipsec pmtu aging infinite - the security association
card crypto outside_map 1 match address outside_cryptomap
card crypto outside_map 1 set pfs
peer set card crypto outside_map 1 92.51.193.158
card crypto outside_map 1 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5
outside_map card crypto 1jeu ikev2 AES AES192 AES256 3DES ipsec-proposal
outside_map interface card crypto outside
trustpool crypto ca policy
IKEv2 crypto policy 1
aes-256 encryption
integrity sha
Group 2 of 5
FRP sha
second life 86400
IKEv2 crypto policy 10
aes-192 encryption
integrity sha
Group 2 of 5
FRP sha
second life 86400
IKEv2 crypto policy 20
aes encryption
integrity sha
Group 2 of 5
FRP sha
second life 86400
IKEv2 crypto policy 30
3des encryption
integrity sha
Group 2 of 5
FRP sha
second life 86400
IKEv2 crypto policy 40
the Encryption
integrity sha
Group 2 of 5
FRP sha
second life 86400
Crypto ikev2 allow outside
Crypto ikev1 allow outside
IKEv1 crypto policy 10
authentication crack
aes-256 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 20
authentication rsa - sig
aes-256 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 30
preshared authentication
aes-256 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 40
authentication crack
aes-192 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 50
authentication rsa - sig
aes-192 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 60
preshared authentication
aes-192 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 70
authentication crack
aes encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 80
authentication rsa - sig
aes encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 90
preshared authentication
aes encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 100
authentication crack
3des encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 110
authentication rsa - sig
3des encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 120
preshared authentication
3des encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 130
authentication crack
the Encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 140
authentication rsa - sig
the Encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 150
preshared authentication
the Encryption
sha hash
Group 2
life 86400
Telnet timeout 5
SSH 77.75.100.208 255.255.255.240 outside
SSH 92.51.193.156 255.255.255.252 outside
SSH timeout 5
Console timeout 0dhcpd outside auto_config
!
a basic threat threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
internal GroupPolicy_92.51.193.158 group strategy
attributes of Group Policy GroupPolicy_92.51.193.158
VPN-tunnel-Protocol ikev1, ikev2
username password 6e6Djaz3W/XH59zX gordon encrypted privilege 15
tunnel-group 92.51.193.158 type ipsec-l2l
tunnel-group 92.51.193.158 General-attributes
Group - default policy - GroupPolicy_92.51.193.158
IPSec-attributes tunnel-group 92.51.193.158
IKEv1 pre-shared-key *.
remote control-IKEv2 pre-shared-key authentication *.
pre-shared-key authentication local IKEv2 *.
!
class-map inspection_default
match default-inspection-traffic
!
!
type of policy-card inspect dns preset_dns_map
parameters
maximum message length automatic of customer
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the preset_dns_map dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
inspect the rsh
inspect the rtsp
inspect esmtp
inspect sqlnet
inspect the skinny
inspect sunrpc
inspect xdmcp
inspect the sip
inspect the netbios
inspect the tftp
Review the ip options
inspect the icmp
!
global service-policy global_policy
context of prompt hostname
no remote anonymous reporting call
Cryptochecksum:83b2069fa311e6037163ae74f9b2bec2
: endHello
There are some clear problems I see on a quick glance. These are not related to the actual VPN configuration but rather the NAT configurations.
All your configuration of NAT CLI format above are configured as manual NAT / double NAT in Section 1. This means that the appliance NAT configurations have been added to the same section of the NAT configurations and scheduling of the NAT inside this Section rules is the cause of the problem for the L2L VPN connection for some.
Here are a few suggestions on what to change
ASA1
Minimal changes
the object of the LAN network
192.168.10.0 subnet 255.255.255.0
being REMOTE-LAN network
255.255.255.0 subnet 192.168.100.0
NAT (inside, outside) 1 static source LAN LAN to static destination REMOTE - LAN LAN
no nat source (indoor, outdoor) public static NETWORK_OBJ_192.168.10.0_24 NETWORK_OBJ_192.168.10.0_24 NETWORK_OBJ_192.168.100.0_24 NETWORK_OBJ_192.168.100.0_24 non-proxy-arp-search of route static destination
That means foregoing is first of all create 'object' that contain the local LAN and remote LANs. Then, it creates a NAT0 rule and adds to the top rules NAT. (number 1). It is essentially of at least one of the problems preventing the VPN operation or traffic that cross.
Finally, we remove the old rule that generated the ASDM. It would do the same thing if it has been moved to the top, but I generally find the creation of the 'object' with descriptive names easier on the eyes in the long term.
Other suggestions
These changes are not necessary with regard to the VPN L2L. Here are some suggestions how to clean a part of NAT configurations.
PAT-SOURCE network object-group
source networks internal PAT Description
object-network 192.168.10.0 255.255.255.0
object-network 192.168.20.0 255.255.255.0
object-network 192.168.40.0 255.255.255.0
NAT interface (it is, outside) the after-service automatic PAT-SOURCE dynamic source
No source (indoor, outdoor) nat Dynamics one interface
no nat (wireless, outdoors) source Dynamics one interface
no nat (servers, outside) no matter what source dynamic interface
The above configuration creates a "object-group" that lists all internal networks that you have dynamic PAT configured so far. It then uses the ' object-group ' in a command unique 'nat' to manage the dynamic PAT for all internal networks (with the exception of printers who had nothing at first). Then we remove the old PAT dynamic configurations.
Contains the command "nat" "car after" because it moving this "nat" configuration to the bottom of the NAT rules. For this reason its less likely to cause problems in the future.
network of the SERVERS object
subnet 192.168.20.0 255.255.255.0
network of the VPN-POOL object
192.168.50.0 subnet 255.255.255.0
NAT (servers, external) 2 static static source of destination of SERVERS SERVERS VPN-VPN-POOL
no nat (servers, external) static source NETWORK_OBJ_192.168.20.0_24 NETWORK_OBJ_192.168.20.0_24 NETWORK_OBJ_192.168.50.0_24 NETWORK_OBJ_192.168.50.0_24 non-proxy-arp-search of route static destination
The above configuration is supposed to create a NAT0 configuration for traffic between the network and the pool of Client VPN server. To my knowledge the old configuration that remove us is not used because the traffic would have matched PAT rule dynamic server yet rather than this rule which is later in the NAT configurations and would not be addressed.
no nat source (indoor, outdoor) public static NETWORK_OBJ_192.168.10.0_24 NETWORK_OBJ_192.168.10.0_24 NETWORK_OBJ_192.168.1.0_24 NETWORK_OBJ_192.168.1.0_24 non-proxy-arp-search of route static destination
It seems to me that network 192.168.1.0/24 is not configured from anywhere in your network. Therefore, the above 'nat' configuration seems useless, can be deleted. If I missed something and its use in then of course do not remove it.
ASA2
Minimal changes
the object of the LAN network
255.255.255.0 subnet 192.168.100.0
being REMOTE-LAN network
192.168.10.0 subnet 255.255.255.0
NAT (inside, outside) 1 static source LAN LAN to static destination REMOTE - LAN LAN
no nat source (indoor, outdoor) public static NETWORK_OBJ_192.168.100.0_24 NETWORK_OBJ_192.168.100.0_24 NETWORK_OBJ_192.168.10.0_24 NETWORK_OBJ_192.168.10.0_24 non-proxy-arp-search of route static destination
That means foregoing is first of all create 'object' that contain the local LAN and remote LANs. Then, it creates a NAT0 rule and adds to the top rules NAT. (number 1). It is essentially of at least one of the problems preventing the VPN operation or traffic that cross.
Finally, we remove the old rule that generated the ASDM.
Other suggestions
PAT-SOURCE network object-group
object-network 192.168.100.0 255.255.255.0
NAT interface (it is, outside) the after-service automatic PAT-SOURCE dynamic source
No source (indoor, outdoor) nat Dynamics one interface
The above configuration is supposed to do the same thing with the other ASA. Although given that this network contains only a single subnet it cleans the "nat" configurations exist that much. But the order of the "nat" configurations is changed to avoid further problems with the NAT order.
no nat source (indoor, outdoor) public static NETWORK_OBJ_192.168.100.0_24 NETWORK_OBJ_192.168.100.0_24 NETWORK_OBJ_192.168.1.0_24 NETWORK_OBJ_192.168.1.0_24 non-proxy-arp-search of route static destination
It seems to me that network 192.168.1.0/24 is not configured from anywhere in your network. Therefore, the above 'nat' configuration seems useless, can be deleted. If I missed something and its use in then of course do not remove it.
I suggest trying the changes related to VPN L2L first NAT0 configurations and test traffic. So who gets the work of connectivity, then you could consider changing other NAT configurations. There are other things that could be changed also in what concerns THAT static NAT servers but that probably better left for another time.
Hope this makes any sense and has helped
Remember to mark a reply as the answer if it answered your question.
Feel free to ask more if necessary
-Jouni
-
ASA 5505 <>ASA 5510 VPN Site to Site
Try to configure a vpn site-to site beetween an ASA 5505 and a 5510. I can't get anything thrown, there are now debugging messages or the other. I must have done something wrong, I followed this paper: http://www.cisco.com/en/US/products/ps6120/products_configuration_example09186a0080950890.shtml but I can't make it work. Anyone can have a peek at my configs, maybe I forgot something.
OK, if you go ahead and add this command to all two firewalls 'inside access management' and try to one side inside the 10.21.32.10 ping always nothing passing by?
-
Cisco ASA 5510 VPN with PIX 515
Hello
I have VPN between Cisco ASA and Cisco PIX.
I saw in my syslog server this error that appears once a day, more or less:
Received a package encrypted with any HIS correspondent, drop
I ve seen issue in another post, but in none of then the solution.
Here are my files from the firewall configuration:
Output from the command: 'show running-config '.
: Saved
:
ASA Version 8.2 (1)
Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac
life crypto ipsec security association seconds 28800
Crypto ipsec kilobytes of life - safety 4608000 association
card crypto WAN_map2 2 corresponds to the address WAN_cryptomap_1
card crypto WAN_map2 2 set pfs
card crypto WAN_map2 2 peer 62.80.XX game. XX
map WAN_map2 2 game of transformation-ESP-DES-MD5 crypto
card crypto WAN_map2 2 defined security-association 2700 seconds life
card crypto WAN_map2 2 set nat-t-disable
card crypto WAN_map2 WAN interface
enable LAN crypto ISAKMP
ISAKMP crypto enable WAN
crypto ISAKMP policy 1
preshared authentication
the Encryption
md5 hash
Group 5
lifetime 28800
No encryption isakmp nat-traversal
tunnel-group 62.80.XX. XX type ipsec-l2l
tunnel-group 62.80.XX. IPSec-attributes of XX
pre-shared-key *.++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
8.0 (4) version PIX
!
Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac
life crypto ipsec security association seconds 28800
Crypto ipsec kilobytes of life - safety 4608000 association
card encryption VPN_map2 3 corresponds to the address VPN_cryptomap_2
card encryption VPN_map2 3 set pfs
card crypto VPN_map2 3 peer 194.30.XX game. XX
VPN_map2 3 transform-set ESP-DES-MD5 crypto card game
card encryption VPN_map2 3 defined security-association life seconds 2700
card encryption VPN_map2 3 set security-association kilobytes of life 4608000
card VPN_map2 3 set nat-t-disable encryption
VPN crypto map VPN_map2 interface
crypto ISAKMP enable VPN
crypto ISAKMP allow inside
crypto ISAKMP policy 30
preshared authentication
the Encryption
md5 hash
Group 5
lifetime 28800
No encryption isakmp nat-traversal
ISAKMP crypto am - disable
attributes of Group Policy DfltGrpPolicy
Protocol-tunnel-VPN IPSec
tunnel-group 194.30.XX. XX type ipsec-l2l
tunnel-group 194.30.XX. IPSec-attributes of XX
pre-shared-key *.If you need more information dedailed ask me questions.
Thanks in advance for your help.
Javi
Hi Javi,
Please after the release of "see broadcasting DfltGrpPolicy of any political group." See if you have the "vpn-idle-timoeout" command configured in that. If so, please change to "vpn-idle-timeout no" and see if that stops at these popping up error messages.
http://www.Cisco.com/en/us/docs/security/ASA/asa80/command/reference/uz.html#wp1571426
Thank you and best regards,
Assia
-
Hi all.
I search the internet to find a way or all first, whether it is possible to do what I want to do, but I can't find anything corresponding to what I'm looking for. Possible that I don't have the right keyword.
We change our old Pix 515e this weekend and for any new ASA 5510.
With this new facility, I want to implement Radius Authentication for the user remote vpn. Change the firewall of the company is an important factor and for the first phase, the user will keep authenticate locally but I need that in phase 2, they will be authenticated through a radius server.
Is there a way to configure both user authentication remote vpn?
For example.
All users will be authenticated locally unless the service member COMPUTER that is authenticated by the radius to the testing server.
I have remote vpn users anywhere in the world if I don't want these users are blocked by the radius authentication test. What I want is that users in Group1 will be authenticated locally on the SAA and users in group2 will be authenticated by the RADIUS. During the test will be done, all users will gradually transfer for radius authentication.
Is it possible
Thank you
Jonathan
Network administrator
Hi Jonathan,.
The best way to go about this would be that you set up another group strategy & corresponding tunnel group named Test and set up Radius Authentication for VPN group using the link below: -.
Ones you have done test and feel confident, you can change the type of authentication for the Production Group. The reverse could be implemented double authentication as RADIUS and if it does not use local but personally I'll put up a group of test and then those I am confident, that I'll change the strategy of Production Group to use the Radius Server to auth.
Manish
-
% 7-ASA-710005: request TCP thrown error in the Client VPN Site to CISCO ASA 5510
Hi friends,
I am trying to built customer to site VPN CISCO ASA 5510 8.4 (4) and get error below when connecting to a cisco VPN client software. Also, I'm below ASA, log. Please help me to reslove.
Error in CISCO VPN Client software:
Secure VPN connection terminated locally by the client.
Reason: 414: unable to establish a TCP connection.
Error in CISCO ASA 5510
7-ASA-710005%: TCP request and eliminated from
49276 outward: 10000 The ASA configuration:
XYZ # sh run
: Saved
:
ASA Version 8.4 (4)
!
hostname XYZ
domain XYZ
activate the password encrypted 3uLkVc9JwRA1/OXb N3
activate the encrypted password of R/x90UjisGVJVlh2
2KFQnbNIdI.2KYOU encrypted passwd
names of
!
interface Ethernet0/0
nameif outside_rim
security-level 0
IP 1.1.1.1 255.255.255.252
!
interface Ethernet0/1
full duplex
nameif XYZ_DMZ
security-level 50
IP 172.1.1.1 255.255.255.248
!
interface Ethernet0/2
Speed 100
full duplex
nameif outside
security-level 0
IP address 2.2.2.2 255.255.255.252
!
interface Ethernet0/3
Speed 100
full duplex
nameif inside
security-level 100
IP 3.3.3.3 255.255.255.224
!
interface Management0/0
Shutdown
No nameif
no level of security
no ip address
!
boot system Disk0: / asa844 - k8.bin
passive FTP mode
DNS domain-lookup outside
DNS server-group DefaultDNS
Server name xx.xx.xx.xx
Server name xx.xx.xx.xx
Server name xx.xx.xx.xx
Server name xx.xx.xx.xx
domain XYZ
network object obj - 172.17.10.3
Home 172.17.10.3
network object obj - 10.1.134.0
10.1.134.0 subnet 255.255.255.0
network object obj - 208.75.237.0
208.75.237.0 subnet 255.255.255.0
network object obj - 10.7.0.0
10.7.0.0 subnet 255.255.0.0
network object obj - 172.17.2.0
172.17.2.0 subnet 255.255.255.0
network object obj - 172.17.3.0
172.17.3.0 subnet 255.255.255.0
network object obj - 172.19.2.0
172.19.2.0 subnet 255.255.255.0
network object obj - 172.19.3.0
172.19.3.0 subnet 255.255.255.0
network object obj - 172.19.7.0
172.19.7.0 subnet 255.255.255.0
network object obj - 10.1.0.0
10.1.0.0 subnet 255.255.0.0
network object obj - 10.2.0.0
10.2.0.0 subnet 255.255.0.0
network object obj - 10.3.0.0
10.3.0.0 subnet 255.255.0.0
network object obj - 10.4.0.0
10.4.0.0 subnet 255.255.0.0
network object obj - 10.6.0.0
10.6.0.0 subnet 255.255.0.0
network object obj - 10.9.0.0
10.9.0.0 subnet 255.255.0.0
network object obj - 10.11.0.0
10.11.0.0 subnet 255.255.0.0
network object obj - 10.12.0.0
10.12.0.0 subnet 255.255.0.0
network object obj - 172.19.1.0
172.19.1.0 subnet 255.255.255.0
network object obj - 172.21.2.0
172.21.2.0 subnet 255.255.255.0
network object obj - 172.16.2.0
172.16.2.0 subnet 255.255.255.0
network object obj - 10.19.130.201
Home 10.19.130.201
network object obj - 172.30.2.0
172.30.2.0 subnet 255.255.255.0
network object obj - 172.30.3.0
172.30.3.0 subnet 255.255.255.0
network object obj - 172.30.7.0
172.30.7.0 subnet 255.255.255.0
network object obj - 10.10.1.0
10.10.1.0 subnet 255.255.255.0
network object obj - 10.19.130.0
10.19.130.0 subnet 255.255.255.0
network of object obj-XXXXXXXX
host XXXXXXXX
network object obj - 145.248.194.0
145.248.194.0 subnet 255.255.255.0
network object obj - 10.1.134.100
Home 10.1.134.100
network object obj - 10.9.124.100
Home 10.9.124.100
network object obj - 10.1.134.101
Home 10.1.134.101
network object obj - 10.9.124.101
Home 10.9.124.101
network object obj - 10.1.134.102
Home 10.1.134.102
network object obj - 10.9.124.102
Home 10.9.124.102
network object obj - 115.111.99.133
Home 115.111.99.133
network object obj - 10.8.108.0
10.8.108.0 subnet 255.255.255.0
network object obj - 115.111.99.129
Home 115.111.99.129
network object obj - 195.254.159.133
Home 195.254.159.133
network object obj - 195.254.158.136
Home 195.254.158.136
network object obj - 209.164.192.0
subnet 209.164.192.0 255.255.224.0
network object obj - 209.164.208.19
Home 209.164.208.19
network object obj - 209.164.192.126
Home 209.164.192.126
network object obj - 10.8.100.128
subnet 10.8.100.128 255.255.255.128
network object obj - 115.111.99.130
Home 115.111.99.130
network object obj - 10.10.0.0
subnet 10.10.0.0 255.255.0.0
network object obj - 115.111.99.132
Home 115.111.99.132
network object obj - 10.10.1.45
Home 10.10.1.45
network object obj - 10.99.132.0
10.99.132.0 subnet 255.255.255.0
the Serversubnet object-group network
object-network 10.10.1.0 255.255.255.0
network-object 10.10.5.0 255.255.255.192
the XYZ_destinations object-group network
object-network 10.1.0.0 255.255.0.0
object-network 10.2.0.0 255.255.0.0
network-object 10.3.0.0 255.255.0.0
network-object 10.4.0.0 255.255.0.0
network-object 10.6.0.0 255.255.0.0
network-object 10.7.0.0 255.255.0.0
network-object 10.11.0.0 255.255.0.0
object-network 10.12.0.0 255.255.0.0
object-network 172.19.1.0 255.255.255.0
object-network 172.19.2.0 255.255.255.0
object-network 172.19.3.0 255.255.255.0
object-network 172.19.7.0 255.255.255.0
object-network 172.17.2.0 255.255.255.0
object-network 172.17.3.0 255.255.255.0
object-network 172.16.2.0 255.255.255.0
object-network 172.16.3.0 255.255.255.0
host of the object-Network 10.50.2.206
the XYZ_us_admin object-group network
network-object 10.3.1.245 255.255.255.255
network-object 10.5.33.7 255.255.255.255
network-object 10.211.5.7 255.255.255.255
network-object 10.3.33.7 255.255.255.255
network-object 10.211.3.7 255.255.255.255
the XYZ_blr_networkdevices object-group network
object-network 10.200.10.0 255.255.255.0
access list XYZ extended ip 10.19.130.0 allow 255.255.255.0 145.248.194.0 255.255.255.0
access list XYZ extended ip 10.19.130.0 allow 255.255.255.0 host 172.16.2.21
access list XYZ extended ip 10.19.130.0 allow 255.255.255.0 host 172.16.2.22
access list XYZ extended ip 10.19.130.0 allow 255.255.255.0 host XXXXXXXX
Access extensive list ip 10.19.130.0 XYZ_PAT allow 255.255.255.0 any
Access extensive list ip 10.1.134.0 XYZ_PAT allow 255.255.255.0 host 195.254.159.133
Access extensive list ip 10.1.134.0 XYZ_PAT allow 255.255.255.0 host 195.254.158.136
Access extensive list ip 10.1.134.0 XYZ_PAT allow 255.255.255.0 any
Access extensive list ip 10.1.134.0 XYZ_PAT allow 255.255.255.0 209.164.192.0 255.255.224.0
Access extensive list ip 10.1.134.0 XYZ_PAT allow 255.255.255.0 host 209.164.208.19
Access extensive list ip 10.1.134.0 XYZ_PAT allow 255.255.255.0 host 209.164.192.126
IP 10.1.134.0 allow Access-list extended sheep 255.255.255.0 208.75.237.0 255.255.255.0
Allow Access-list extended sheep 255.255.255.0 10.1.134.0 IP 10.7.0.0 255.255.0.0
IP 10.1.134.0 allow Access-list extended sheep 255.255.255.0 172.17.2.0 255.255.255.0
IP 10.1.134.0 allow Access-list extended sheep 255.255.255.0 172.17.3.0 255.255.255.0
IP 10.1.134.0 allow Access-list extended sheep 255.255.255.0 172.19.2.0 255.255.255.0
IP 10.1.134.0 allow Access-list extended sheep 255.255.255.0 172.19.3.0 255.255.255.0
IP 10.1.134.0 allow Access-list extended sheep 255.255.255.0 172.19.7.0 255.255.255.0
10.1.134.0 IP Access-list extended sheep 255.255.255.0 allow 10.1.0.0 255.255.0.0
10.1.134.0 IP Access-list extended sheep 255.255.255.0 allow 10.2.0.0 255.255.0.0
Allow Access-list extended sheep 255.255.255.0 10.1.134.0 IP 10.3.0.0 255.255.0.0
10.1.134.0 IP Access-list extended sheep 255.255.255.0 allow 10.4.0.0 255.255.0.0
10.1.134.0 IP Access-list extended sheep 255.255.255.0 allow 10.6.0.0 255.255.0.0
Allow Access-list extended sheep 255.255.255.0 10.1.134.0 IP 10.9.0.0 255.255.0.0
Allow Access-list extended sheep 255.255.255.0 10.1.134.0 IP 10.11.0.0 255.255.0.0
10.1.134.0 IP Access-list extended sheep 255.255.255.0 allow 10.12.0.0 255.255.0.0
IP 10.1.134.0 allow Access-list extended sheep 255.255.255.0 172.19.1.0 255.255.255.0
IP 10.1.134.0 allow Access-list extended sheep 255.255.255.0 172.21.2.0 255.255.255.0
10.1.134.0 IP Access-list extended sheep 255.255.255.0 allow 172.16.2.0 255.255.255.0
access-list extended sheep allowed host ip 10.19.130.201 172.30.2.0 255.255.255.0
access-list extended sheep allowed host ip 10.19.130.201 172.30.3.0 255.255.255.0
access-list extended sheep allowed host ip 10.19.130.201 172.30.7.0 255.255.255.0
access-list extended sheep allowed ip object-group Serversubnet-group of objects XYZ_destinations
10.10.1.0 IP Access-list extended sheep 255.255.255.0 allow 10.2.0.0 255.255.0.0
10.19.130.0 IP Access-list extended sheep 255.255.255.0 allow host XXXXXXXX
IP 10.19.130.0 allow Access-list extended sheep 255.255.255.0 145.248.194.0 255.255.255.0
Access extensive list ip 10.8.108.0 Guest_PAT allow 255.255.255.0 any
CACIB list extended access permitted ip 10.8.100.128 255.255.255.128 145.248.194.0 255.255.255.0
Access extensive list ip 10.8.100.128 Cacib_PAT allow 255.255.255.128 all
Access extensive list ip 10.1.134.0 New_Edge allow 255.255.255.0 208.75.237.0 255.255.255.0
Allow XYZ_global to access extended list ip 10.7.0.0 255.255.0.0 10.1.134.0 255.255.255.0
Access extensive list ip 10.1.134.0 XYZ_global allow 255.255.255.0 10.7.0.0 255.255.0.0
Access extensive list ip 172.17.2.0 XYZ_global allow 255.255.255.0 10.1.134.0 255.255.255.0
Access extensive list ip 172.17.3.0 XYZ_global allow 255.255.255.0 10.1.134.0 255.255.255.0
Access extensive list ip 172.19.2.0 XYZ_global allow 255.255.255.0 10.1.134.0 255.255.255.0
Access extensive list ip 172.19.3.0 XYZ_global allow 255.255.255.0 10.1.134.0 255.255.255.0
Access extensive list ip 172.19.7.0 XYZ_global allow 255.255.255.0 10.1.134.0 255.255.255.0
Access extensive list ip 10.1.0.0 XYZ_global allow 255.255.0.0 10.1.134.0 255.255.255.0
Access extensive list 10.2.0.0 ip XYZ_global 255.255.0.0 allow 10.1.134.0 255.255.255.0
Allow XYZ_global to access extended list ip 10.3.0.0 255.255.0.0 10.1.134.0 255.255.255.0
Access extensive list 10.4.0.0 ip XYZ_global 255.255.0.0 allow 10.1.134.0 255.255.255.0
Access extensive list 10.6.0.0 ip XYZ_global 255.255.0.0 allow 10.1.134.0 255.255.255.0
Access extensive list ip 10.9.0.0 XYZ_global allow 255.255.0.0 10.1.134.0 255.255.255.0
Allow XYZ_global to access extended list ip 10.11.0.0 255.255.0.0 10.1.134.0 255.255.255.0
Access extensive list 10.12.0.0 ip XYZ_global 255.255.0.0 allow 10.1.134.0 255.255.255.0
Access extensive list ip 172.19.1.0 XYZ_global allow 255.255.255.0 10.1.134.0 255.255.255.0
Access extensive list ip 172.21.2.0 XYZ_global allow 255.255.255.0 10.1.134.0 255.255.255.0
Access extensive list ip 10.1.134.0 XYZ_global allow 255.255.255.0 172.17.2.0 255.255.255.0
Access extensive list ip 10.1.134.0 XYZ_global allow 255.255.255.0 172.17.3.0 255.255.255.0
Access extensive list ip 10.1.134.0 XYZ_global allow 255.255.255.0 172.19.2.0 255.255.255.0
Access extensive list ip 10.1.134.0 XYZ_global allow 255.255.255.0 172.19.3.0 255.255.255.0
Access extensive list ip 10.1.134.0 XYZ_global allow 255.255.255.0 172.19.7.0 255.255.255.0
Access extensive list ip 10.1.134.0 XYZ_global allow 255.255.255.0 10.1.0.0 255.255.0.0
Access extensive list ip 10.1.134.0 XYZ_global allow 255.255.255.0 10.2.0.0 255.255.0.0
Access extensive list ip 10.1.134.0 XYZ_global allow 255.255.255.0 10.3.0.0 255.255.0.0
Access extensive list ip 10.1.134.0 XYZ_global allow 255.255.255.0 10.4.0.0 255.255.0.0
Access extensive list ip 10.1.134.0 XYZ_global allow 255.255.255.0 10.6.0.0 255.255.0.0
Access extensive list ip 10.1.134.0 XYZ_global allow 255.255.255.0 10.9.0.0 255.255.0.0
Access extensive list ip 10.1.134.0 XYZ_global allow 255.255.255.0 10.11.0.0 255.255.0.0
Access extensive list ip 10.1.134.0 XYZ_global allow 255.255.255.0 10.12.0.0 255.255.0.0
Access extensive list ip 10.1.134.0 XYZ_global allow 255.255.255.0 172.19.1.0 255.255.255.0
Access extensive list ip 10.1.134.0 XYZ_global allow 255.255.255.0 172.21.2.0 255.255.255.0
XYZ_global to access extended list ip 172.16.2.0 allow 255.255.255.0 10.1.134.0 255.255.255.0
Access extensive list ip 10.1.134.0 XYZ_global allow 255.255.255.0 172.16.2.0 255.255.255.0
Access extensive list ip 172.30.2.0 XYZ_global allow 255.255.255.0 host 10.19.130.201
XYZ_global list extended access allowed host ip 10.19.130.201 172.30.2.0 255.255.255.0
Access extensive list ip 172.30.3.0 XYZ_global allow 255.255.255.0 host 10.19.130.201
XYZ_global list extended access allowed host ip 10.19.130.201 172.30.3.0 255.255.255.0
Access extensive list ip 172.30.7.0 XYZ_global allow 255.255.255.0 host 10.19.130.201
XYZ_global list extended access allowed host ip 10.19.130.201 172.30.7.0 255.255.255.0
XYZ_global list extended access permitted ip object-group Serversubnet-group of objects XYZ_destinations
XYZ_global list extended access permitted ip object-group XYZ_destinations-group of objects Serversubnet
ML_VPN list extended access allowed host ip 115.111.99.129 209.164.192.0 255.255.224.0
permit access list extended ip host 115.111.99.129 ML_VPN 209.164.208.19
permit access list extended ip host 115.111.99.129 ML_VPN 209.164.192.126
permit access list extended ip host 10.9.124.100 Da_VPN 10.125.81.88
permit access list extended ip host 10.9.124.101 Da_VPN 10.125.81.88
permit access list extended ip host 10.9.124.102 Da_VPN 10.125.81.88
Da_VPN list extended access allowed host ip 10.9.124.100 10.125.81.0 255.255.255.0
Da_VPN list extended access allowed host ip 10.9.124.101 10.125.81.0 255.255.255.0
Da_VPN list extended access allowed host ip 10.9.124.102 10.125.81.0 255.255.255.0
Sr_PAT to access extended list ip 10.10.0.0 allow 255.255.0.0 any
Da_Pd_VPN list extended access allowed host ip 10.9.124.100 10.125.80.64 255.255.255.192
Da_Pd_VPN list extended access allowed host ip 10.9.124.100 10.125.64.0 255.255.240.0
permit access list extended ip host 10.9.124.100 Da_Pd_VPN 10.125.85.46
permit access list extended ip host 10.9.124.100 Da_Pd_VPN 10.125.86.46
Da_Pd_VPN list extended access allowed host ip 10.9.124.101 10.125.80.64 255.255.255.192
Da_Pd_VPN list extended access allowed host ip 10.9.124.101 10.125.64.0 255.255.240.0
permit access list extended ip host 10.9.124.101 Da_Pd_VPN 10.125.85.46
permit access list extended ip host 10.9.124.101 Da_Pd_VPN 10.125.86.46
Da_Pd_VPN list extended access allowed host ip 10.9.124.102 10.125.80.64 255.255.255.192
Da_Pd_VPN list extended access allowed host ip 10.9.124.102 10.125.64.0 255.255.240.0
permit access list extended ip host 10.9.124.102 Da_Pd_VPN 10.125.85.46
permit access list extended ip host 10.9.124.102 Da_Pd_VPN 10.125.86.46
Access extensive list ip 10.19.130.0 XYZ_reliance allow 255.255.255.0 145.248.194.0 255.255.255.0
access-list coextended permit ip host 2.2.2.2 XXXXXXXX
access-list coextended allow the host ip XXXXXXXXhost 2.2.2.2
permitted this access list extended ip 10.1.134.0 255.255.255.0 208.75.237.0 255.255.255.0
permitted this access list extended ip 208.75.237.0 255.255.255.0 10.1.134.0 255.255.255.0
access list acl-outside extended permit ip host 57.66.81.159 172.17.10.3
access list acl-outside extended permit ip host 80.169.223.179 172.17.10.3
access list acl-outside scope permit ip any host 172.17.10.3
access list acl-outside extended permitted tcp any host 10.10.1.45 eq https
access list acl-outside extended permit tcp any any eq 10000
access list acl-outside extended deny ip any any newspaper
pager lines 10
Enable logging
debug logging in buffered memory
outside_rim MTU 1500
MTU 1500 XYZ_DMZ
Outside 1500 MTU
Within 1500 MTU
IP pool local XYZ_c2s_vpn_pool 172.30.10.51 - 172.30.10.254
ICMP unreachable rate-limit 1 burst-size 1
ICMP allow all outside
ICMP allow any inside
don't allow no asdm history
ARP timeout 14400
NAT (inside, all) source static obj - 10.1.134.0 obj - 10.1.134.0 destination static obj - 208.75.237.0 obj - 208.75.237.0 no-proxy-arp-search to itinerary
NAT (inside, all) source static obj - 10.1.134.0 obj - 10.1.134.0 destination static obj - 10.7.0.0 obj - 10.7.0.0 no-proxy-arp-search to itinerary
NAT (inside, all) source static obj - 10.1.134.0 obj - 10.1.134.0 destination static obj - 172.17.2.0 obj - 172.17.2.0 no-proxy-arp-search to itinerary
NAT (inside, all) source static obj - 10.1.134.0 obj - 10.1.134.0 destination static obj - 172.17.3.0 obj - 172.17.3.0 no-proxy-arp-search to itinerary
NAT (inside, all) source static obj - 10.1.134.0 obj - 10.1.134.0 destination static obj - 172.19.2.0 obj - 172.19.2.0 no-proxy-arp-search to itinerary
NAT (inside, all) source static obj - 10.1.134.0 obj - 10.1.134.0 destination static obj - 172.19.3.0 obj - 172.19.3.0 no-proxy-arp-search to itinerary
NAT (inside, all) source static obj - 10.1.134.0 obj - 10.1.134.0 destination static obj - 172.19.7.0 obj - 172.19.7.0 no-proxy-arp-search to itinerary
NAT (inside, all) source static obj - 10.1.134.0 obj - 10.1.134.0 destination static obj - 10.1.0.0 obj - 10.1.0.0 non-proxy-arp-search to itinerary
NAT (inside, all) source static obj - 10.1.134.0 obj - 10.1.134.0 destination static obj - 10.2.0.0 obj - 10.2.0.0 non-proxy-arp-search to itinerary
NAT (inside, all) source static obj - 10.1.134.0 obj - 10.1.134.0 destination static obj - 10.3.0.0 obj - 10.3.0.0 no-proxy-arp-search to itinerary
NAT (inside, all) source static obj - 10.1.134.0 obj - 10.1.134.0 destination static obj - 10.4.0.0 obj - 10.4.0.0 non-proxy-arp-search to itinerary
NAT (inside, all) source static obj - 10.1.134.0 obj - 10.1.134.0 destination static obj - 10.6.0.0 obj - 10.6.0.0 non-proxy-arp-search to itinerary
NAT (inside, all) source static obj - 10.1.134.0 obj - 10.1.134.0 destination static obj - 10.9.0.0 obj - 10.9.0.0 no-proxy-arp-search to itinerary
NAT (inside, all) source static obj - 10.1.134.0 obj - 10.1.134.0 destination static obj - 10.11.0.0 obj - 10.11.0.0 no-proxy-arp-search to itinerary
NAT (inside, all) source static obj - 10.1.134.0 obj - 10.1.134.0 destination static obj - 10.12.0.0 obj - 10.12.0.0 non-proxy-arp-search to itinerary
NAT (inside, all) source static obj - 10.1.134.0 obj - 10.1.134.0 destination static obj - 172.19.1.0 obj - 172.19.1.0 no-proxy-arp-search to itinerary
NAT (inside, all) source static obj - 10.1.134.0 obj - 10.1.134.0 destination static obj - 172.21.2.0 obj - 172.21.2.0 no-proxy-arp-search to itinerary
NAT (inside, all) source static obj - 10.1.134.0 obj - 10.1.134.0 destination static obj - 172.16.2.0 obj - 172.16.2.0 non-proxy-arp-search to itinerary
NAT (inside, all) source static obj - 10.19.130.201 obj - 10.19.130.201 destination static obj - 172.30.2.0 obj - 172.30.2.0 no-proxy-arp-search to itinerary
NAT (inside, all) source static obj - 10.19.130.201 obj - 10.19.130.201 destination static obj - 172.30.3.0 obj - 172.30.3.0 no-proxy-arp-search to itinerary
NAT (inside, all) source static obj - 10.19.130.201 obj - 10.19.130.201 destination static obj - 172.30.7.0 obj - 172.30.7.0 no-proxy-arp-search to itinerary
NAT (inside, all) static source Serversubnet Serversubnet XYZ_destinations XYZ_destinations non-proxy-arp-search of route static destination
NAT (inside, all) source static obj - 10.10.1.0 obj - 10.10.1.0 destination static obj - 10.2.0.0 obj - 10.2.0.0 non-proxy-arp-search to itinerary
NAT (inside, all) source static obj - 10.19.130.0 obj - 10.19.130.0 destination static obj-XXXXXXXX XXXXXXXX - obj non-proxy-arp-search to itinerary
NAT (inside, all) source static obj - 10.19.130.0 obj - 10.19.130.0 destination static obj - 145.248.194.0 obj - 145.248.194.0 no-proxy-arp-search to itinerary
NAT source (indoor, outdoor), obj static obj - 10.1.134.100 - 10.9.124.100
NAT source (indoor, outdoor), obj static obj - 10.1.134.101 - 10.9.124.101
NAT source (indoor, outdoor), obj static obj - 10.1.134.102 - 10.9.124.102
NAT interface dynamic obj - 10.8.108.0 source (indoor, outdoor)
NAT (inside, outside) source dynamic obj - 10.19.130.0 obj - 115.111.99.129
NAT (inside, outside) source dynamic obj - 10.1.134.0 obj - 115.111.99.129 destination static obj - 195.254.159.133 obj - 195.254.159.133
NAT (inside, outside) source dynamic obj - 10.1.134.0 obj - 115.111.99.129 destination static obj - 195.254.158.136 obj - 195.254.158.136
NAT (inside, outside) source dynamic obj - 10.1.134.0 obj - 115.111.99.129
NAT (inside, outside) source dynamic obj - 10.1.134.0 obj - 115.111.99.129 destination static obj - 209.164.192.0 obj - 209.164.192.0
NAT (inside, outside) source dynamic obj - 10.1.134.0 obj - 115.111.99.129 destination static obj - 209.164.208.19 obj - 209.164.208.19
NAT (inside, outside) source dynamic obj - 10.1.134.0 obj - 115.111.99.129 destination static obj - 209.164.192.126 obj - 209.164.192.126
NAT (inside, outside) source dynamic obj - 10.8.100.128 obj - 115.111.99.130
NAT (inside, outside) source dynamic obj - 10.10.0.0 obj - 115.111.99.132
NAT source (indoor, outdoor), obj static obj - 10.10.1.45 - 115.111.99.133
NAT (inside, outside) source dynamic obj - 10.99.132.0 obj - 115.111.99.129
!
network object obj - 172.17.10.3
NAT (XYZ_DMZ, outside) static 115.111.99.134
Access-group acl-outside in external interface
Route outside 0.0.0.0 0.0.0.0 115.111.23.129 1
Route outside 0.0.0.0 0.0.0.0 115.254.127.130 10
Route inside 10.10.0.0 255.255.0.0 10.8.100.1 1
Route inside 10.10.1.0 255.255.255.0 10.8.100.1 1
Route inside 10.10.5.0 255.255.255.192 10.8.100.1 1
Route inside 10.8.100.128 255.255.255.128 10.8.100.1 1
Route inside 10.8.108.0 255.255.255.0 10.8.100.1 1
Route inside 10.19.130.0 255.255.255.0 10.8.100.1 1
Route inside 10.99.4.0 255.255.255.0 10.99.130.254 1
Route inside 10.99.132.0 255.255.255.0 10.8.100.1 1
Route inside 10.1.134.0 255.255.255.0 10.8.100.1 1
Route outside 208.75.237.0 255.255.255.0 115.111.23.129 1
Timeout xlate 03:00
Pat-xlate timeout 0:00:30
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
Floating conn timeout 0:00:00
dynamic-access-policy-registration DfltAccessPolicy
identity of the user by default-domain LOCAL
AAA authentication LOCAL telnet console
LOCAL AAA authorization command
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown cold start
Crypto ipsec transform-set esp-aes-256 ikev1, esp-sha-hmac vpn2
Crypto ipsec transform-set esp-aes-256 ikev1, esp-md5-hmac vpn6
Crypto ipsec transform-set esp-aes-256 ikev1, esp-sha-hmac vpn5
Crypto ipsec transform-set esp-aes-256 ikev1, esp-md5-hmac vpn7
Crypto ipsec transform-set esp-aes-256 ikev1, esp-sha-hmac vpn4
Crypto ipsec transform-set esp-aes-256 ikev1, esp-sha-hmac vpn1
Crypto ipsec transform-set esp-aes-256 ikev1, esp-sha-hmac vpn_reliance
Crypto ipsec transform-set esp-3des esp-md5-hmac ikev1 c2s_vpn
86400 seconds, duration of life crypto ipsec security association
Crypto-map dynamic dyn1 ikev1 transform-set c2s_vpn 1 set
Crypto-map dynamic dyn1 1jeu reverse-road
card crypto vpn 1 corresponds to the address XYZ
card 1 set of peer XYZ Peer IP vpn crypto
1 set transform-set vpn1 ikev1 vpn crypto card
card crypto vpn 1 lifetime of security set association, 3600 seconds
card crypto vpn 1 set security-association life kilobytes 4608000
correspondence vpn crypto card address 2 DON'T
2 peer NE_Peer IP vpn crypto card game
2 set transform-set vpn2 ikev1 vpn crypto card
3600 seconds, duration of life card crypto vpn 2 set security-association
card crypto vpn 2 set security-association life kilobytes 4608000
card crypto vpn 4 corresponds to the address ML_VPN
card crypto vpn 4 set pfs
vpn crypto card game 4 peers ML_Peer IP
4 set transform-set vpn4 ikev1 vpn crypto card
3600 seconds, duration of life card crypto vpn 4 set - the security association
card crypto vpn 4 set security-association life kilobytes 4608000
vpn crypto card 5 corresponds to the address XYZ_global
vpn crypto card game 5 peers XYZ_globa_Peer IP
5 set transform-set vpn5 ikev1 vpn crypto card
3600 seconds, duration of life card crypto vpn 5 set - the security association
card 5 security-association life set vpn crypto kilobytes 4608000
vpn crypto card 6 corresponds to the address Da_VPN
vpn crypto card game 6 peers Da_VPN_Peer IP
6 set transform-set vpn6 ikev1 vpn crypto card
3600 seconds, duration of life card crypto vpn 6 set - the security association
card crypto vpn 6 set security-association life kilobytes 4608000
vpn crypto card 7 corresponds to the address Da_Pd_VPN
7 peer Da_Pd_VPN_Peer IP vpn crypto card game
7 set transform-set vpn6 ikev1 vpn crypto card
3600 seconds, duration of life card crypto vpn 7 set - the security association
card crypto vpn 7 set security-association life kilobytes 4608000
vpn outside crypto map interface
crypto map vpn_reliance 1 corresponds to the address XYZ_rim
card crypto vpn_reliance 1 set of peer XYZ_rim_Peer IP
card crypto 1 ikev1 transform-set vpn_reliance set vpn_reliance
vpn_reliance card crypto 1 lifetime of security set association, 3600 seconds
card crypto vpn_reliance 1 set security-association life kilobytes 4608000
card crypto vpn_reliance interface outside_rim
dynamic mymap 1 dyn1 ipsec-isakmp crypto map
crypto isakmp identity address
No encryption isakmp nat-traversal
Crypto ikev1 enable outside_rim
Crypto ikev1 allow outside
IKEv1 crypto policy 1
preshared authentication
aes-256 encryption
sha hash
Group 5
lifetime 28800
IKEv1 crypto policy 2
preshared authentication
aes-256 encryption
sha hash
Group 5
life 86400
IKEv1 crypto policy 4
preshared authentication
aes-256 encryption
sha hash
Group 5
life 28000
IKEv1 crypto policy 5
preshared authentication
aes-256 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 100
preshared authentication
3des encryption
sha hash
Group 2
life 43200
IKEv1 crypto policy 65535
preshared authentication
3des encryption
sha hash
Group 2
life 86400
Telnet 10.8.100.0 255.255.255.224 inside
Telnet timeout 5
SSH timeout 5
SSH group dh-Group1-sha1 key exchange
Console timeout 0
no basic threat threat detection
no statistical access list - a threat detection
no statistical threat detection tcp-interception
internal XYZ_c2s_vpn group strategy
username testadmin encrypted password oFJjANE3QKoA206w
tunnel-group XXXXXXXX type ipsec-l2l
tunnel-group ipsec-attributes XXXXXXXX
IKEv1 pre-shared-key *.
tunnel-group XXXXXXXXtype ipsec-l2l
tunnel-group XXXXXXXXipsec-attributes
IKEv1 pre-shared-key *.
tunnel-group XXXXXXXX type ipsec-l2l
tunnel-group ipsec-attributes XXXXXXXX
IKEv1 pre-shared-key *.
tunnel-group XXXXXXXX type ipsec-l2l
tunnel-group ipsec-attributes XXXXXXXX
IKEv1 pre-shared-key *.
tunnel-group XXXXXXXX type ipsec-l2l
tunnel-group ipsec-attributes XXXXXXXX
IKEv1 pre-shared-key *.
tunnel-group XXXXXXXX type ipsec-l2l
tunnel-group ipsec-attributes XXXXXXXX
IKEv1 pre-shared-key *.
tunnel-group XXXXXXXX type ipsec-l2l
tunnel-group ipsec-attributes XXXXXXXX
IKEv1 pre-shared-key *.
type tunnel-group XYZ_c2s_vpn remote access
attributes global-tunnel-group XYZ_c2s_vpn
address pool XYZ_c2s_vpn_pool
IPSec-attributes tunnel-group XYZ_c2s_vpn
IKEv1 pre-shared-key *.
!
class-map inspection_default
match default-inspection-traffic
!
!
type of policy-card inspect dns preset_dns_map
parameters
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the preset_dns_map dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
inspect the netbios
inspect the rsh
inspect the rtsp
inspect the skinny
inspect esmtp
inspect sqlnet
inspect sunrpc
inspect the tftp
inspect the sip
inspect xdmcp
inspect the icmp
Review the ip options
!
global service-policy global_policy
level 3 privilege see the running-config command exec mode
logging of orders privilege see the level 3 exec mode
privilege see the level 3 exec mode command crypto
context of prompt hostname
no remote anonymous reporting call
call-home
Profile of CiscoTAC-1
no active account
http https://tools.cisco.com/its/service/oddce/services/DDCEService destination address
email address of destination [email protected] / * /
destination-mode http transport
Subscribe to alert-group diagnosis
Subscribe to alert-group environment
Subscribe to alert-group monthly periodic inventory
monthly periodicals to subscribe to alert-group configuration
daily periodic subscribe to alert-group telemetry
Cryptochecksum:caa7476cd348ed89b95d37d4e3c9e1d8
: endXYZ #.
Good news
Follow these steps:
network object obj - 172.30.10.0_24
172.30.10.0 subnet 255.255.255.0
!
the LOCAL_NETWORKS_VPN object-group network
object-network 1.1.1.0 255.255.255.0
!
NAT (inside, outside) 1 static source LOCAL_NETWORKS_VPN destination LOCAL_NETWORKS_VPN static obj - 172.30.10.0_24 obj - 172.30.10.0_24 - route search
* Where 1.1.1.0/24 is the internal network that you want to reach through the tunnel.
Keep me posted.
Thank you.
Please note all messages that will be useful.
-
Cisco ASA 5510 multiple dynamic config VPN L2L necessary
Hello
We have a Cisco asa 5510 with static IP address. Also, we have a remote office with a dynamic IP address. We now have a dynamic to static VPN configured L2L. And now, we must add new tunnel to another site with a dynamic IP address. Is this possible? Does anyone have an example of woking, or manual?
Oleg Kobelev
The config only you need in the ASA is: -.
(1) set of crypto processing
(2) political ISAKMP
(3) dynamic Crypto map
(4) default group L2L & PSK
(5) Config RRI (reverse Route Injection)
HTH >
-
False claims RADIUS of customer VPN Cisco ASA 5510
Hello world
I use the Cisco VPN client 5.0.7 and Cisco ASA 5510 (7.4 and 8.4.2) VPN RAS solution. Clients are authenticated using certificates and RADIUS AAA (ACS 3.3) and AD.
Each time, when the client connects, ASA 2 RADIUS requests questions, correct first - which is successfully authenticated by FAC and immediately - second that always fails. I couldn't find information related to this strange behaivor. Function "Double Authentication" (more sympathetic to his name) is only accessible to Anyconnect customers who we do not. When I'm authenicated by using password group, there is only one query RADIUS.
What is the source of such behavior?
The negative impact is that my logs are filled with the failed authentication attempts fallacious and users are incrementig attempts failed in the AD meter.
Debugging of ASA:
-First application-
RDS 2011-10-24 16:16:01 0232 14884 request code 172.16.8.1:1645 host = 1 id = 22, length = 145 on port 1025
RDS 2011-10-24 16:16:01 I 2519 14884 [001] value of username: User1
RDS 2011-10-24 16:16:01 I 2519 14884 [002] value username-password: 2D A9 B2 D0 15 5F 1E B8 BB DB 3A 38 F5 24 72 B5
RDS 2011-10-24 16:16:01 I 2538 14884 [005] NAS-Port value:-1072693248
RDS 2011-10-24 16:16:01 I 2538 14884 [006] Type of Service value: 2
RDS 2011-10-24 16:16:01 I 2538 14884 [007] value Framed-Protocol: 1
RDS 2011-10-24 16:16:01 I 2519 14884 [030] value Called-Station-Id: 172.16.8.1
RDS 2011-10-24 16:16:01 I 2519 14884 [031] value of Calling-Station-Id: 10.4.14.14
RDS 2011-10-24 16:16:01 I 2538 14884 [061] NAS-Port-Type value: 5
RDS 2011-10-24 16:16:01 I 2533 14884 [066] Tunnel-Client-Endpoint value: [T1] 10.4.14.14
RDS 2011-10-24 16:16:01 I 14884 2556 [004] value of NAS-IP-Address: 172.16.8.1
RDS 2011-10-24 16:16:01 I 2561 14884 [026] Vendor-Specific vsa id: 9
RDS 2011-10-24 16:16:01 I 2596 14884 [001] cisco-av-pair value: ip:source - ip = 10.4.14.14
RDS 2011-10-24 16:16:01 I 0282 14884 ExtensionPoint: run the configured scan extension points...
RDS 2011-10-24 16:16:01 I 0314 14884 ExtensionPoint: advertising [AuthenticationExtension] provider [Cisco EAP generic]
RDS 2011-10-24 16:16:01 I 0763 14884 ExtensionPoint: Message-[generic EAP] lack of EAP, ignorant...
RDS 2011-10-24 16:16:01 I 0319 14884 ExtensionPoint: [GenericEAP.dll-> AuthenticationExtension] returned [1 - ignored]
RDS 2011-10-24 16:16:01 I 0314 14884 ExtensionPoint: asking provider [Download Cisco ACL] [AuthenticationExtension]
RDS 2011-10-24 16:16:01 I 0763 14884 ExtensionPoint: [DnldACLs] asking not a download of ACL, ignorant...
RDS 2011-10-24 16:16:01 I 0319 14884 ExtensionPoint: [DnldACLs.dll-> AuthenticationExtension] returned [1 - ignored]
RDS 2011-10-24 16:16:02 I 14884 0475 AuthorExtensionPoint: run the configured scan extension points...
RDS 2011-10-24 16:16:02 I 14884 0507 AuthorExtensionPoint: requesting provider [Download Cisco ACL] [AuthorisationExtension]
RDS 2011-10-24 16:16:02 I 0763 14884 ExtensionPoint: looking for ACL from [DnldACLs] to [user1]
RDS 2011-10-24 16:16:02 I 0512 14884 AuthorExtensionPoint: [DnldACLs.dll-> AuthorisationExtension] returned [1 - ignored]
RDS 2011-10-24 16:16:02 3360 14884 sent response code 2, id 22 to 172.16.8.1 on port 1025
RDS 2011-10-24 16:16:02 I 2561 14884 [026] Vendor-Specific vsa id: 9
RDS 2011-10-24 16:16:02 I 2596 14884 [001] cisco-av-pair value: ip:addr - pool = vpnpool
RDS 2011-10-24 16:16:02 I 2561 14884 [026] Vendor-Specific vsa id: 9
RDS 2011-10-24 16:16:02 I 2596 14884 [001] cisco-av-pair value: ip:wins - servers = 10.2.9.12 10.3.9.10 10.4.2.202
RDS 2011-10-24 16:16:02 I 2561 14884 [026] Vendor-Specific vsa id: 9
RDS 2011-10-24 16:16:02 I 2596 14884 [001] cisco-av-pair value: IP: DNS-servers = 10.2.9.12 10.3.9.10 10.4.2.202
RDS 2011-10-24 16:16:02 I 2538 14884 [006] Type of Service value: 2
RDS 2011-10-24 16:16:02 I 2538 14884 [007] value Framed-Protocol: 1
RDS 2011-10-24 16:16:02 I 2538 14884 [013] box-Compression value: 1
RDS 2011-10-24 16:16:02 I 14884 2556 [008] value box-IP-Address: 255.255.255.254
RDS 2011-10-24 16:16:02 I 2519 14884 [025] value class: CISCOACS:002cb2a9/ac100801/3222274048
-The second request-
RDS 2011-10-24 16:16:02 0232 14884 request code 172.16.8.1:1645 host = 1 id = 23, length = 145 on port 1025
RDS 2011-10-24 16:16:02 I 2519 14884 [001] value of username: User1
RDS 2011-10-24 16:16:02 I 2519 14884 [002] value username-password: 06 EA 08 AB C7 8F 75 D0 A5 E5 AE B7 A8 1 48 96 b
RDS 2011-10-24 16:16:02 I 2538 14884 [005] NAS-Port value:-1072693248
RDS 2011-10-24 16:16:02 I 2538 14884 [006] Type of Service value: 2
RDS 2011-10-24 16:16:02 I 2538 14884 [007] value Framed-Protocol: 1
RDS 2011-10-24 16:16:02 I 2519 14884 [030] value Called-Station-Id: 172.16.8.1
RDS 2011-10-24 16:16:02 I 2519 14884 [031] value of Calling-Station-Id: 10.4.14.14
RDS 2011-10-24 16:16:02 I 2538 14884 [061] NAS-Port-Type value: 5
RDS 2011-10-24 16:16:02 I 2533 14884 [066] Tunnel-Client-Endpoint value: [T1] 10.4.14.14
RDS 2011-10-24 16:16:02 I 14884 2556 [004] value of NAS-IP-Address: 172.16.8.1
RDS 2011-10-24 16:16:02 I 2561 14884 [026] Vendor-Specific vsa id: 9
RDS 2011-10-24 16:16:02 I 2596 14884 [001] cisco-av-pair value: ip:source - ip = 10.4.14.14
RDS 2011-10-24 16:16:02 I 0282 14884 ExtensionPoint: run the configured scan extension points...
RDS 2011-10-24 16:16:02 I 0314 14884 ExtensionPoint: advertising [AuthenticationExtension] provider [Cisco EAP generic]
RDS 2011-10-24 16:16:02 I 0763 14884 ExtensionPoint: Message-[generic EAP] lack of EAP, ignorant...
RDS 2011-10-24 16:16:02 I 0319 14884 ExtensionPoint: [GenericEAP.dll-> AuthenticationExtension] returned [1 - ignored]
RDS 2011-10-24 16:16:02 I 0314 14884 ExtensionPoint: asking provider [Download Cisco ACL] [AuthenticationExtension]
RDS 2011-10-24 16:16:02 I 0763 14884 ExtensionPoint: [DnldACLs] asking not a download of ACL, ignorant...
RDS 2011-10-24 16:16:02 I 0319 14884 ExtensionPoint: [DnldACLs.dll-> AuthenticationExtension] returned [1 - ignored]
RDS 2011-10-24 16:16:02 P 2237 14884 user: User1 - Windows user unknown or invalid password
RDS 2011-10-24 16:16:02 3360 14884 sent response code 3, id 23 to 172.16.8.1 on port 1025
RDS 2011-10-24 16:16:02 I 2519 14884 [018] value Reply-Message: rejected...
RDS 2011-10-24 16:16:03 0232 14884 request code 10.2.47.200:1812 host = 1 id = 254, length = 227 on port 32769
RDS 2011-10-24 16:16:03 2788 14884 (VSA unknown Vendor ID 14179)
GBA debug:
-First application-
AUTH 24/10/2011 16:16:01 I 0365 13060 external DB [NTAuthenDLL.dll]: from [user01] user authentication
AUTH 24/10/2011 16:16:01 I 0365 13060 external DB [NTAuthenDLL.dll]: Windows authentication attempt for the user1 userAUTH 24/10/2011 16:16:02 I 0365 13060 external DB [NTAuthenDLL.dll]: authentication Windows successfully (by DCCORPMSK04)
AUTH 24/10/2011 16:16:02 I 0365 13060 external DB [NTAuthenDLL.dll]: information get RAS to the user user1 DCCORPMSK04-The second request-
AUTH 24/10/2011 16:16:02 I 0365 13060 external DB [NTAuthenDLL.dll]: from [user1] user authentication
AUTH 24/10/2011 16:16:02 I 0365 13060 external DB [NTAuthenDLL.dll]: Windows authentication attempt for the user1 user
AUTH 24/10/2011 16:16:02 0365 13060 external DB [NTAuthenDLL.dll]: Windows authentication FAILED (Error 1326 L)
AUTH 24/10/2011 16:16:02 I 0365 13060 external DB [NTAuthenDLL.dll]: retry authentication to the CORP domain
AUTH 24/10/2011 16:16:02 I 0365 13060 external DB [NTAuthenDLL.dll]: Windows authentication attempt for the user1 user
AUTH 24/10/2011 16:16:02 0365 13060 external DB [NTAuthenDLL.dll]: Windows authentication FAILED (Error 1326 L)The ASA config:
Crypto ikev1 allow outside
Crypto ikev1 allow inside
IKEv1 crypto ipsec-over-tcp port 10000
life 86400
IKEv1 crypto policy 65535
authentication rsa - sig
3des encryption
md5 hash
Group 2
life 86400!
internal Cert_auth group strategy
attributes of Group Policy Cert_auth
client ssl-VPN-tunnel-Protocol ikev1 l2tp ipsec
Split-tunnel-policy tunnelspecified
value of Split-tunnel-network-list aclVPN2
the address value vpnpool pools
rule of access-client-none!
attributes global-tunnel-group DefaultRAGroup
address (inside) vpnpool pool
address vpnpool pool
authentication-server-group RADIUS01
authorization-server-group RADIUS01
authorization-server-group (inside) RADIUS01
Group Policy - by default-Cert_auth!
RADIUS protocol AAA-server RADIUS01
AAA-server host 10.2.9.224 RADIUS01 (inside)
key *.
RADIUS-common-pw *.
AAA-server host 10.4.2.223 RADIUS01 (inside)
key *.Hello
It is a 'classic' error and has nothing to do with dual authentication, but rather with the fact that you do both radius and authorization of RADIUS authentication.
If you remove this line:
authorization-server-group RADIUS01
you will see that it starts to work properly
In short: when ASA no authorization of RADIUS, it sends a request to access radius with the username as a password, that's why you see the second application fails all the time.
This is because the RADIUS authorization is intended to be used when authentication happens using certificates (only) so there is no password.
Also note that within the RADIUS protocol, authentication and authorization are not separate things, both occur in a single step. So if the ASA makes the radius authentication, he already gets the user attributes in the authentication step and it makes no sense to also make a separate authorization stage (except in a few very rare scenario where you have 2 radius servers, one for authentication and another for permission).
HTH
Herbert
-
Cisco ASA 5510 + license + AIP - SSM
Hello.
I have this box.
I have a few questions about it.
(1) I'll be able to update the firmware (from 8.2 to 8.3 or greater for example) without smarnet for ASA 5510? And what can not do without smartnet?
(2) I have only AIP-SSM-10 module this ASA 5510. is there a smartnet, too? And when I buy only one module is it build in a subscription for 1 year for the signatures of the IPS?
(3) if I have the Cisco ASA 5510 base license, my IPS on AIP-SSM-10 will work?
(4) as I foresee in a purchase of the year a 5510 more with the same module and mount ther of failover. I really need license Security more than failover (active / standby)? For active/active, I know I need one, Yes?
Please help me.
(1) you must Smartnet in order to download the software from the download from cisco.com site.
(2) Yes, there is also a smartnet for the AIP module. Module AIP does not come with one year subscription, but you can ask for a demo license.
(3) Yes, the basic license is OK for the AIP module.
(4) Yes, you would need license security more on the two ASA to be able to run any type of failover on ASA5510.
Hope that answers your questions.
-
How to activate IP accounting or capture packets in Cisco ASA 5510 (8.2)
Hi all
Please help me for activation
IP accounting packets or capture in Cisco ASA 5510 (8.2).
Thank you
Solene
Hi Eric,.
Create a list of access with the source destination ip address and/or tcp/udp ports
can use it
CAP_NAME access-list ACL_NAME buffer 12345bytes INT_NAME capture interface
You can check capture
See the capture?
Name Capture PASSWORD
| Output modifiers
Take care
PaulC
-
Cisco ASA 5510 - IOS upgrade 7.0 failing. Not found Flash BIOS
Hello everyone
I have a Cisco ASA 5510 in a lab with none of the configurations environment what so ever.
Objective: upgrade the IOS current version 7.0 (8) to 7.1.1 (possibly go to 8.2 until memory upgrade on the SAA: 256 MB to 1 GB and then move to the latest version of 8.2 IOS).
Output to see the attached Version.
Output Flash attached show.
asa711 - k8.bin is the file that has been copied from a TFTP server to flash.
The following commands have been executed in order to update the IOS
ciscoasa (config) # boot flash system: / asa711 - k8.bin
INFO: Conversion of flash: / asa711 - k8.bin to disk0: / asa711 - k8.bin
ciscoasa (config) #.
ciscoasa (config) # end
ciscoasa # write memory
Cryptochecksum: aaaa08ce ccde38f2 19c42e08 dea24cbd
2713 bytes copied in 1,450 dry (2713 bytes/s)
[OK]
ciscoasa # reloadPROBLEM: the device ASA goes in an infinite loop (guard restart). This is the message on the console:
The system boot, please wait...
CISCO SYSTEMS
Embedded BIOS Version 1.0 (11) 15:11:51.82 5 08/28/08
Memory: 631ko
Memory: 256 MB
PCI device table.
Bus Dev Func VendID DevID class Irq
00 00 00 8086 2578 host Bridge
00 01 00 8086 2579 PCI to PCI bridge
00 03 00 8086 PCI bridge to PCI 257 b
00 1 00 8086 PCI bridge to PCI 25AE
1 d 00 00 8086 25A 9 Serial Bus 11
1 00 01 8086 25AA Bus series 10 d
1 d 00 04 8086 25AB system
1 d 00 05 8086 25AC IRQ controller
1 d 00 07 8086 25AD Bus series 9
1E 00 00 8086 PCI bridge to 244th PCI
1F 00 00 8086 25A 1 ISA Bridge
1F 00 02 8086 25 IDE controller has 3 11
1F 00 03 8086 25A 4 Bus series 5
1F 00 05 8086 25A 6 Audio 5
02 01 00 8086 1075 Ethernet 11
03 01 00 177 D 0003 encrypt/decrypt 9
03 02 00 8086 1079 Ethernet 9
03 02 01 8086 1079 Ethernet 9
03 03 00 8086 1079 Ethernet 9
03 03 01 8086 1079 Ethernet 9
04 02 00 8086 1209 Ethernet 11
04 03 00 8086 1209 Ethernet 5
Evaluate the BIOS Options...
Launch of the BIOS Extension installation ROMMON
Cisco Systems ROMMON Version (1.0 (11) 5) #0: Thu Aug 28 15:23:50 CDT 2008
Platform ASA5510
Use BREAK or ESC to interrupt the boot.
Use the SPACE to start boot immediately.
Start the program boot...
Startup configuration file contains 1 entry.Load disk0: / asa711 - k8.bin... The starting...
256 MB OF RAM
Total of SSMs found: 0
Total cards network found: 7
mcwa i82557 Ethernet to irq 11 MAC: 0024.974a.65af
mcwa i82557 Ethernet to the irq 5 MAC: 0000.0001.0001
Not found BIOS flash.
Reset...The only way for me to do things to normal is if I BREAK the sequence starting with ESC and go into ROMMON mode. I then issue a start command for the SAA to start with 7.0 (8) default IOS Image.
Please can someone explain what is the problem here?
Apologies if I'm missing something obvious that I'm not an expert of the SAA.
Looks like that the ASA is hitting a field notice: fn62378. The FN, it's because of the incompatible version of hardware and software. Please upgrade to version 7.1.2 instead of 7.1.1. If you plan to spend in 8.2. So instead of going 7.1.2 you could go to 7.2.5 (recommanded), then 8.2.5
http://www.Cisco.com/c/en/us/support/docs/field-notices/620/fn62378.html
It will be useful.
Kind regards
Akshay Rouanet
Remember messages useful rate.
-
in my cisco asa 5510 heartbeat interface
Cisco asa 5510 heartbeat interface
Of course, we will need to more information than what you have given to us. Next time, don't even bother if you want to help us...
-
ASA 5505 VPN Site to site with several networks
Hello
I have a Cisco ASA 5505 configuration problem and hope you can help me.
Our company created a second facility, which must be connected using VPN to our headquarters.
I used the ASDM "Wizard of Site to site VPN" to create a connection, which works very well with our main network.
Following structure:
Headquarters:
Cisco ASA 5505, firmware 9.1, ASDM version 7.1
Outside: Fixed IP
Inside: IP address of the interface is 192.168.0.1/24 (data network)
Now I have a second network 192.168.1.0/24 (VoIP network), PBX address is 192.168.1.10.
The two networks should be accessible through the VPN.
New installation:
Cisco ASA 5505, firmware 9.1, ASDM version 7.1
Outside: Fixed IP
Inside: IP address of the interface is 192.168.2.1/24
I have already created a connection until a PC of the new plant reaches the data network. For example, a ping from 192.168.2.100 to 192.168.0.100 is possible.
Now, I want to add some VoIP phones to the new facility, which can reach the PBX on 192.168.1.10.
In the link, I have already added the two networks as remote network:
object-group network Testgroup network-object 192.168.0.0 255.255.255.0 network-object 192.168.1.0 255.255.255.0 access-list outside_cryptomap extended permit ip object-group Testgroup object Remote-Network
My problem now is, I don't know what to define as 'Bridge' on my PBX.
I can't use 192.168.0.1 because it's a different subnet. Also, I can not put a second IP 192.168.1.1 to the interface of the ASA.
You have any ideas, how can I accomplish this, so that the two subnets are accessed through the VPN and all devices have a defined gateway?
Could a "Easy VPN Remote" in "Network Mode" you help me?
What is the difference between 'Site-to-site' and 'extended network '?
Kind regards
Daniel condition, look for the solution GmbH
You can optionally configure a new LAN VIRTUAL (VLAN PBX) on the SAA and connect this interface to the voice network.
If you do not have a spare on the ASA port, then Yes, you have a router to route traffic from the PBX to the ASA via the data network.
-
Cisco ASA 5510 L2L VPN on the backup interface
OK, here is what I have and I even if I knew how to do this, but it has not worked for me. I hope someone out there can help you.
I have an ASA 5510 running 8.4 with double configuration of ISPs on 2 different interfaces: outside (primary), backup (backup). I also have a site to site VPN ASA another in another city. The VPN is now configured on the external interface and works very well. What I wanted to do, is to make the VPN running on backup interface only.
So, I changed the card encryption on the remote side to use the backup interface IP and created a tunnel-group for her. Then, I created a map encryption for backup interface and activated ikev1 on it. The default route is configured to use the external interface, so I created a static route that routes traffic destined for the external interface of the remote side to the backup interface default gateway. I can get to establish tunnels, but no traffic passes through them. I have however while I need a NAT device for the tunnel traffic to I created a NAT so but still no transmitted traffic. I tried the packet - trace and he said: the traffic was allowed and show its crypto ipsec command, I see the configuration of the tunnel, but no traffic will pass through it. Can anyone help?
Ben,
you use a code to version 8.4, I recommend starting by removing the config NAT statements at both ends. This version does not have the NAT and control, and if you don't need... I've seen instances with 8.4 (3) where a NAT even though apparently correct was causing not to pass through the traffic.
Site A:
NAT (inside, backup) source static obj-SiteALAN obj-SiteALAN static obj-SiteBLAN obj-SiteBLAN
Site b:
NAT (inside, outside) source static obj - 192.168.5.0 obj - 192.168.5.0 destination static obj - 192.168.3.0 obj - 192.168.3.0
If possible, you should increase your AES encryption, but this is a personal point of view and should not stop the traffic through the links. You should be able to see the counters for the data transmitted / received are these incrementing?
Do you have the ACLs that are from the inside to the outside and internal interface to the Interface of backup (duplicated.
In this model, the control is the routing.
Best regards
Ju
-
Cisco ASA 5510 - restrictions of VPN (AnyConnect) based on the AD user or IP address
Hello
I want to test how to restrict access user on an ASA 5510 AnyConnect. In politics, I can define what networks will go through the VPN tunnel and which not (split tunneling). The ASA has a LDAP connection and only AD users with a special security group can connect over AnyConnect.
On the other hand I would like to restrict access for special users within a VPN policy.So my question:
What are your recommendations to implement this szenario?My two ideas would be:
1. the access rules based on the user of the AD.
2. special reserve IP addresses in the pool of addresses AnyConnect for some users, so I can limit access to the normal firewall rules base based on the source IP address.What are your recommendations and is it possible to realize my ideas (and how)?
Thanks in advance
Best regards
Hello
I will suggest that you configure a second ad group in the server and another group strategy in the ASA, you can configure certain access on each group policy "the installer of the filters, assign different split political tunnel, different ACL' and in the ad server, you can assign users for example to the AD Group A and AD Group B based on the access you want to give them now , you must configure LDAP mapping to assign the user specific group policy that you want based on the AD group that they belong.
You can follow this documentation that will help you configure the LDAP Mapping:
http://www.Cisco.com/c/en/us/support/docs/security/ASA-5500-x-series-NEX...
Best regards, please rate.
Maybe you are looking for
-
Missing originals after copying photos for a new mac external HARD disk library. How to fix this?
Move the library of photos hosted on an external HARD during a new mac disc. I can open the app and import new pictures, but I can't change any of my previous photos because he complains that the original is not found. The "Use as system library" but
-
Constantly texting instead of iMessage to a phone number.
I want to be able to send SMS to the phone number of my friend and iMessages to their emails, but the two conversations keep appearing as imessages. Is it possible that I could choose what conversations I want to use texts instead of having to 'send
-
Satellite L500-13W - does not load correctly
HI - he's two months bought new Satellite L500 - all wells and then last week began to have problems charging. As usual, I allowed the battery to run down to approximately 10% of capacity before plugging the power cable. While work noticed immediatel
-
Laptop crashes when you run the virus scan
Whenever I run a scan for viruses from my laptop freezes to a specific file. The file it freezes on what is c:\windows\...\atiihag.inf_31a3846f\gtiihag.inf McAfee advised me to contact Microsoft to find out what the file is and if it is not necessar
-
error code of HP mini 110 [redacted]
I have a hp mini 110 with a bios lock. When you inter passes 3 times, it gives error code [number of Series edited by Moderator]. I could really use some help.