Cisco ASA 5515 - Anyconnect users can connect to ASA, but cannot ping inside the local IP address
Hello!
I have a 5515 ASA with the configuration below. I have configure the ASA as remote access with anyconnect VPN server, now my problem is that I can connect but I can not ping.
ASA Version 9.1 (1)
!
ASA host name
domain xxx.xx
names of
local pool VPN_CLIENT_POOL 192.168.12.1 - 192.168.12.254 255.255.255.0 IP mask
!
interface GigabitEthernet0/0
nameif inside
security-level 100
192.168.11.1 IP address 255.255.255.0
!
interface GigabitEthernet0/1
Description Interface_to_VPN
nameif outside
security-level 0
IP 111.222.333.444 255.255.255.240
!
interface GigabitEthernet0/2
Shutdown
No nameif
no level of security
no ip address
!
interface GigabitEthernet0/3
Shutdown
No nameif
no level of security
no ip address
!
interface GigabitEthernet0/4
Shutdown
No nameif
no level of security
no ip address
!
interface GigabitEthernet0/5
Shutdown
No nameif
no level of security
no ip address
!
interface Management0/0
management only
nameif management
security-level 100
192.168.5.1 IP address 255.255.255.0
!
passive FTP mode
DNS server-group DefaultDNS
www.ww domain name
permit same-security-traffic intra-interface
the object of the LAN network
subnet 192.168.11.0 255.255.255.0
LAN description
network of the SSLVPN_POOL object
255.255.255.0 subnet 192.168.12.0
VPN_CLIENT_ACL list standard access allowed 192.168.11.0 255.255.255.0
pager lines 24
Enable logging
asdm of logging of information
Within 1500 MTU
Outside 1500 MTU
management of MTU 1500
no failover
ICMP unreachable rate-limit 1 burst-size 1
ASDM image disk0: / asdm - 711.bin
don't allow no asdm history
ARP timeout 14400
no permit-nonconnected arp
NAT (exterior, Interior) static source SSLVPN_POOL SSLVPN_POOL static destination LAN LAN
Route outside 0.0.0.0 0.0.0.0 111.222.333.443 1
Timeout xlate 03:00
Pat-xlate timeout 0:00:30
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
Floating conn timeout 0:00:00
dynamic-access-policy-registration DfltAccessPolicy
WebVPN
list of URLS no
identity of the user by default-domain LOCAL
the ssh LOCAL console AAA authentication
AAA authentication http LOCAL console
LOCAL AAA authorization exec
Enable http server
http 192.168.5.0 255.255.255.0 management
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown warmstart of cold start
Crypto ipsec pmtu aging infinite - the security association
Crypto ca trustpoint ASDM_TrustPoint5
Terminal registration
E-mail [email protected] / * /
name of the object CN = ASA
address-IP 111.222.333.444
Configure CRL
Crypto ca trustpoint ASDM_TrustPoint6
Terminal registration
domain name full vpn.domain.com
E-mail [email protected] / * /
name of the object CN = vpn.domain.com
address-IP 111.222.333.444
pair of keys sslvpn
Configure CRL
trustpool crypto ca policy
string encryption ca ASDM_TrustPoint6 certificates
Telnet timeout 5
SSH 192.168.11.0 255.255.255.0 inside
SSH timeout 30
Console timeout 0
No ipv6-vpn-addr-assign aaa
no local ipv6-vpn-addr-assign
192.168.5.2 management - dhcpd addresses 192.168.5.254
!
a basic threat threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
SSL-trust outside ASDM_TrustPoint6 point
WebVPN
allow outside
CSD image disk0:/csd_3.5.2008-k9.pkg
AnyConnect image disk0:/anyconnect-win-3.1.04066-k9.pkg 1
AnyConnect enable
tunnel-group-list activate
attributes of Group Policy DfltGrpPolicy
Ikev1 VPN-tunnel-Protocol l2tp ipsec without ssl-client
internal VPN_CLIENT_POLICY group policy
VPN_CLIENT_POLICY group policy attributes
WINS server no
value of server DNS 192.168.11.198
VPN - 5 concurrent connections
VPN-session-timeout 480
client ssl-VPN-tunnel-Protocol
Split-tunnel-policy tunnelspecified
value of Split-tunnel-network-list VPN_CLIENT_ACL
myComp.local value by default-field
the address value VPN_CLIENT_POOL pools
WebVPN
activate AnyConnect ssl dtls
AnyConnect Dungeon-Installer installed
AnyConnect ssl keepalive 20
time to generate a new key 30 AnyConnect ssl
AnyConnect ssl generate a new method ssl key
AnyConnect client of dpd-interval 30
dpd-interval gateway AnyConnect 30
AnyConnect dtls lzs compression
AnyConnect modules value vpngina
value of customization DfltCustomization
internal IT_POLICY group policy
IT_POLICY group policy attributes
WINS server no
value of server DNS 192.168.11.198
VPN - connections 3
VPN-session-timeout 120
Protocol-tunnel-VPN-client ssl clientless ssl
Split-tunnel-policy tunnelspecified
value of Split-tunnel-network-list VPN_CLIENT_ACL
field default value societe.com
the address value VPN_CLIENT_POOL pools
WebVPN
activate AnyConnect ssl dtls
AnyConnect Dungeon-Installer installed
AnyConnect ssl keepalive 20
AnyConnect dtls lzs compression
value of customization DfltCustomization
username vpnuser password PA$ encrypted $WORD
vpnuser username attributes
VPN-group-policy VPN_CLIENT_POLICY
type of remote access service
Username vpnuser2 password PA$ encrypted $W
username vpnuser2 attributes
type of remote access service
username admin password ADMINPA$ $ encrypted privilege 15
VPN Tunnel-group type remote access
General-attributes of VPN Tunnel-group
address VPN_CLIENT_POOL pool
Group Policy - by default-VPN_CLIENT_POLICY
VPN Tunnel-group webvpn-attributes
the aaa authentication certificate
enable VPN_to_R group-alias
type tunnel-group IT_PROFILE remote access
attributes global-tunnel-group IT_PROFILE
address VPN_CLIENT_POOL pool
Group Policy - by default-IT_POLICY
tunnel-group IT_PROFILE webvpn-attributes
the aaa authentication certificate
enable IT Group-alias
!
class-map inspection_default
match default-inspection-traffic
!
!
type of policy-card inspect dns preset_dns_map
parameters
maximum message length automatic of customer
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the preset_dns_map dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
inspect the rsh
inspect the rtsp
inspect esmtp
inspect sqlnet
inspect the skinny
inspect sunrpc
inspect xdmcp
inspect the sip
inspect the netbios
inspect the tftp
Review the ip options
inspect the icmp
!
global service-policy global_policy
context of prompt hostname
no remote anonymous reporting call
: end
Help me please! Thank you!
Hello
Please set ACLs to allow ICMP between these two subnets (192.168.11.0 and 192.168.12.0) and check. It should ping. Let me know if it does not work.
Thank you
swap
Tags: Cisco Security
Similar Questions
-
ASA 5540 - cannot ping inside the interface
Hi all. We have recently upgraded PIX to ASA5540 and we saw a strange thing going. In a Word, we can ping the inside interface of the ASA from any beach on our 6500 network (which is connected directly behind the ASA on the inside), but one where our monitoring tools are placed. Inside there is an ACL that allows all of our core networks, but it does not help that the interface is really strange.
In the ASDM, I see messages like this:
ID ICMP echo request: 2004 x.x.x.x y.y.y.y on the inside interface to. I don't think that's the problem, but I could be wrong.
This is also the configuration of the interface VLAN VIRTUAL local area network from which we cannot ping inside the interface we can ping to and since this VLAN and machines without problem. The only problem is ping the inside interface of the ASA.
interface Vlanx
IP x.x.x.x 255.255.255.0
IP broadcast directed to 199
IP accounting output-packets
IP pim sparse - dense mode
route IP cache flow
load-interval 30
Has anyone experiences the problem like this before? Thanks in advance for any help.
Can you post the output of the following on the ASA:-
display the route
And the output of your base layer diverter: -.
show ip route<>
HTH >
-
Hello
I don't know what could be held, vpn users can ping to the outside and inside of the Cisco ASA interface but can not connect to servers or servers within the LAN ping.
is hell config please kindly and I would like to know what might happen.
hostname horse
domain evergreen.com
activate 2KFQnbNIdI.2KYOU encrypted password
2KFQnbNIdI.2KYOU encrypted passwd
names of
ins-guard
!
interface GigabitEthernet0/0
LAN description
nameif inside
security-level 100
192.168.200.1 IP address 255.255.255.0
!
interface GigabitEthernet0/1
Description CONNECTION_TO_FREEMAN
nameif outside
security-level 0
IP 196.1.1.1 255.255.255.248
!
interface GigabitEthernet0/2
Description CONNECTION_TO_TIGHTMAN
nameif backup
security-level 0
IP 197.1.1.1 255.255.255.248
!
interface GigabitEthernet0/3
Shutdown
No nameif
no level of security
no ip address
!
interface Management0/0
Shutdown
No nameif
no level of security
no ip address
management only
!
boot system Disk0: / asa844-1 - k8.bin
boot system Disk0: / asa707 - k8.bin
passive FTP mode
clock timezone WAT 1
DNS server-group DefaultDNS
domain green.com
network of the NETWORK_OBJ_192.168.2.0_25 object
Subnet 192.168.2.0 255.255.255.128
network of the NETWORK_OBJ_192.168.202.0_24 object
192.168.202.0 subnet 255.255.255.0
network obj_any object
subnet 0.0.0.0 0.0.0.0
the DM_INLINE_NETWORK_1 object-group network
object-network 192.168.200.0 255.255.255.0
object-network 192.168.202.0 255.255.255.0
the DM_INLINE_NETWORK_2 object-group network
object-network 192.168.200.0 255.255.255.0
object-network 192.168.202.0 255.255.255.0
access-list extended INSIDE_OUT allow ip 192.168.202.0 255.255.255.0 any
access-list extended INSIDE_OUT allow ip 192.168.200.0 255.255.255.0 any
Access extensive list permits all ip a OUTSIDE_IN
gbnlvpntunnel_splitTunnelAcl standard access list allow 192.168.200.0 255.255.255.0
standard access list gbnlvpntunnel_splitTunnelAcl allow 192.168.202.0 255.255.255.0
gbnlvpntunnell_splitTunnelAcl standard access list allow 192.168.200.0 255.255.255.0
standard access list gbnlvpntunnell_splitTunnelAcl allow 192.168.202.0 255.255.255.0
pager lines 24
Enable logging
asdm of logging of information
Within 1500 MTU
Outside 1500 MTU
backup of MTU 1500
mask of local pool VPNPOOL 192.168.2.0 - 192.168.2.100 IP 255.255.255.0
no failover
ICMP unreachable rate-limit 1 burst-size 1
ASDM image disk0: / asdm-645 - 206.bin
don't allow no asdm history
ARP timeout 14400
NAT (inside, outside) static source NETWORK_OBJ_192.168.202.0_24 NETWORK_OBJ_192.168.202.0_24 NETWORK_OBJ_192.168.2.0_25 NETWORK_OBJ_192.168.2.0_25 non-proxy-arp-search of route static destination
NAT (inside, backup) static source NETWORK_OBJ_192.168.202.0_24 NETWORK_OBJ_192.168.202.0_24 NETWORK_OBJ_192.168.2.0_25 NETWORK_OBJ_192.168.2.0_25 non-proxy-arp-search of route static destination
NAT (inside, outside) static source DM_INLINE_NETWORK_1 DM_INLINE_NETWORK_1 NETWORK_OBJ_192.168.2.0_25 NETWORK_OBJ_192.168.2.0_25 non-proxy-arp-search of route static destination
NAT (inside, backup) static source DM_INLINE_NETWORK_2 DM_INLINE_NETWORK_2 NETWORK_OBJ_192.168.2.0_25 NETWORK_OBJ_192.168.2.0_25 non-proxy-arp-search of route static destination
!
network obj_any object
dynamic NAT interface (inside, backup)
Access-group interface inside INSIDE_OUT
Access-group OUTSIDE_IN in interface outside
Route outside 0.0.0.0 0.0.0.0 196.1.1.2 1 track 10
Route outside 0.0.0.0 0.0.0.0 197.1.1.2 254
Timeout xlate 03:00
Pat-xlate timeout 0:00:30
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
Floating conn timeout 0:00:00
dynamic-access-policy-registration DfltAccessPolicy
identity of the user by default-domain LOCAL
Enable http server
http 192.168.200.0 255.255.255.0 inside
http 192.168.202.0 255.255.255.0 inside
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown cold start
monitor SLA 100
type echo protocol ipIcmpEcho 212.58.244.71 interface outside
Timeout 3000
frequency 5
monitor als 100 calendar life never start-time now
Crypto ipsec transform-set ikev1 ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-DES-SHA esp - esp-sha-hmac
Crypto ipsec transform-set ikev1 SHA-ESP-3DES esp-3des esp-sha-hmac
Crypto ipsec transform-set ikev1 esp ESP-DES-MD5-esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-3DES-MD5-esp-3des esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-128-SHA aes - esp esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-esp - aes esp-md5-hmac
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 pfs Group1 set
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 define ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5
outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP
outside_map interface card crypto outside
backup_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP
backup of crypto backup_map interface card
Crypto ikev1 allow outside
Crypto ikev1 enable backup
IKEv1 crypto policy 10
authentication crack
aes-256 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 20
authentication rsa - sig
aes-256 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 30
preshared authentication
aes-256 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 40
authentication crack
aes-192 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 50
authentication rsa - sig
aes-192 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 60
preshared authentication
aes-192 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 70
authentication crack
aes encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 80
authentication rsa - sig
aes encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 90
preshared authentication
aes encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 100
authentication crack
3des encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 110
authentication rsa - sig
3des encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 120
preshared authentication
3des encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 130
authentication crack
the Encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 140
authentication rsa - sig
the Encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 150
preshared authentication
the Encryption
sha hash
Group 2
life 86400
!
track 10 rtr 100 accessibility
Telnet 192.168.200.0 255.255.255.0 inside
Telnet 192.168.202.0 255.255.255.0 inside
Telnet timeout 5
SSH 192.168.202.0 255.255.255.0 inside
SSH 192.168.200.0 255.255.255.0 inside
SSH 0.0.0.0 0.0.0.0 outdoors
SSH timeout 15
SSH group dh-Group1-sha1 key exchange
Console timeout 0
management-access inside
a basic threat threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
WebVPN
internal group vpntunnel strategy
Group vpntunnel policy attributes
Ikev1 VPN-tunnel-Protocol
Split-tunnel-policy tunnelspecified
value of Split-tunnel-network-list vpntunnel_splitTunnelAcl
field default value green.com
internal vpntunnell group policy
attributes of the strategy of group vpntunnell
Ikev1 VPN-tunnel-Protocol
Split-tunnel-policy tunnelspecified
value of Split-tunnel-network-list gbnlvpntunnell_splitTunnelAcl
field default value green.com
Green user name encrypted BoEFKkDtbnX5Uy1Q privilege 15 password
attributes of user name THE
VPN-group-policy gbnlvpn
tunnel-group vpntunnel type remote access
tunnel-group vpntunnel General attributes
address VPNPOOL pool
strategy-group-by default vpntunnel
tunnel-group vpntunnel ipsec-attributes
IKEv1 pre-shared-key *.
type tunnel-group vpntunnell remote access
tunnel-group vpntunnell General-attributes
address VPNPOOL2 pool
Group Policy - by default-vpntunnell
vpntunnell group of tunnel ipsec-attributes
IKEv1 pre-shared-key *.
!
class-map inspection_default
match default-inspection-traffic
!
!
type of policy-card inspect dns migrated_dns_map_1
parameters
maximum message length automatic of customer
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the migrated_dns_map_1 dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
inspect the rsh
inspect the rtsp
inspect esmtp
inspect sqlnet
inspect the skinny
inspect sunrpc
inspect xdmcp
inspect the sip
inspect the netbios
inspect the tftp
Review the ip options
!
global service-policy global_policy
context of prompt hostname
no remote anonymous reporting call
call-home
Profile of CiscoTAC-1
no active account
http https://tools.cisco.com/its/service/oddce/services/DDCEService destination address
email address of destination [email protected] / * /
destination-mode http transport
Subscribe to alert-group diagnosis
Subscribe to alert-group environment
Subscribe to alert-group monthly periodic inventory
monthly periodicals to subscribe to alert-group configuration
daily periodic subscribe to alert-group telemetry
Cryptochecksum:7c1b1373bf2e2c56289b51b8dccaa565
Hello
1 - Please run these commands:
"crypto isakmp nat-traversal 30.
"crypto than dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 Road opposite value.
The main issue here is that you have two roads floating and outside it has a better than backup metric, that's why I added the command 'reverse-road '.
Please let me know.
Thank you.
-
Can connect to CC on two computers on the same IP address at the same time?
Can connect to CC on two computers on the same IP address at the same time? Because I accidentally opened both and I was wondering if it will affect my membership or denying me access at the mercy of the CC.
Cloud license allows 2 activations http://www.adobe.com/legal/licenses-terms.html
-Install on a 2nd computer http://forums.adobe.com/thread/1452292?tstart=0
-Windows or Mac has no importance... 2 on the same operating system or 1 on each
-Two subscriptions CAN be used at the same time https://forums.adobe.com/thread/1683787
-
I have problems to access the resources within the network when connecting with the Cisco VPN client for a version of 8.4 (3) operation of the IOS Cisco ASA 5510. I tried all new NAT 8.4 orders but cannot access the network interior. I can see traffic in newspapers when ping. I can only assume I have NAT evil or it's because the inside interface of the ASA is on the 24th of the same subnet as the network interior? Please see config below, any suggestion would be appreciated. I configured a VPN site to another in this same 5510 and it works well
Thank you
interface Ethernet0/0
Speed 100
full duplex
nameif outside
security-level 0
IP x.x.x.x 255.255.255.240
!
interface Ethernet0/1
Speed 100
full duplex
nameif inside
security-level 100
IP 10.88.10.254 255.255.255.0
!
interface Management0/0
Shutdown
nameif management
security-level 0
no ip address
!
permit same-security-traffic inter-interface
permit same-security-traffic intra-interface
network of the PAT_to_Outside_ClassA object
10.88.0.0 subnet 255.255.0.0
network of the PAT_to_Outside_ClassB object
subnet 172.16.0.0 255.240.0.0
network of the PAT_to_Outside_ClassC object
Subnet 192.168.0.0 255.255.240.0
network of the LocalNetwork object
10.88.0.0 subnet 255.255.0.0
network of the RemoteNetwork1 object
Subnet 192.168.0.0 255.255.0.0
network of the RemoteNetwork2 object
172.16.10.0 subnet 255.255.255.0
network of the RemoteNetwork3 object
10.86.0.0 subnet 255.255.0.0
network of the RemoteNetwork4 object
10.250.1.0 subnet 255.255.255.0
network of the NatExempt object
10.88.10.0 subnet 255.255.255.0
the Site_to_SiteVPN1 object-group network
object-network 192.168.4.0 255.255.254.0
object-network 172.16.10.0 255.255.255.0
object-network 10.0.0.0 255.0.0.0
outside_access_in deny ip extended access list a whole
inside_access_in of access allowed any ip an extended list
11 extended access-list allow ip 10.250.1.0 255.255.255.0 any
outside_1_cryptomap to access extended list ip 10.88.0.0 255.255.0.0 allow object-group Site_to_SiteVPN1
mask 10.250.1.1 - 10.250.1.254 255.255.255.0 IP local pool Admin_Pool
NAT static NatExempt NatExempt of the source (indoor, outdoor)
NAT (inside, outside) static source any any static destination RemoteNetwork4 RemoteNetwork4-route search
NAT static LocalNetwork LocalNetwork destination (indoor, outdoor) static source RemoteNetwork1 RemoteNetwork1
NAT static LocalNetwork LocalNetwork destination (indoor, outdoor) static source RemoteNetwork2 RemoteNetwork2
NAT static LocalNetwork LocalNetwork destination (indoor, outdoor) static source RemoteNetwork3 RemoteNetwork3
NAT (inside, outside) static source LocalNetwork LocalNetwork static destination RemoteNetwork4 RemoteNetwork4-route search
!
network of the PAT_to_Outside_ClassA object
NAT dynamic interface (indoor, outdoor)
network of the PAT_to_Outside_ClassB object
NAT dynamic interface (indoor, outdoor)
network of the PAT_to_Outside_ClassC object
NAT dynamic interface (indoor, outdoor)
Access-group outside_access_in in interface outside
inside_access_in access to the interface inside group
Route outside 0.0.0.0 0.0.0.0 x.x.x.x 1
dynamic-access-policy-registration DfltAccessPolicy
Sysopt connection timewait
Service resetoutside
Crypto ipsec transform-set ikev1 ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-esp - aes esp-md5-hmac
Crypto ipsec transform-set esp-ikev1 esp-md5-hmac bh-series
Crypto ipsec transform-set ikev1 esp ESP-DES-MD5-esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-3DES-MD5-esp-3des esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-DES-SHA esp - esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-128-SHA aes - esp esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
Crypto ipsec transform-set ikev1 SHA-ESP-3DES esp-3des esp-sha-hmac
Crypto-map dynamic dynmap 10 set pfs
Crypto-map dynamic dynmap 10 set transform-set bh - set ikev1
life together - the association of security crypto dynamic-map dynmap 10 28800 seconds
Crypto-map dynamic dynmap 10 kilobytes of life together - the association of safety 4608000
Crypto-map dynamic dynmap 10 the value reverse-road
card crypto mymap 1 match address outside_1_cryptomap
card crypto mymap 1 set counterpart x.x.x.x
card crypto mymap 1 set transform-set ESP-AES-256-SHA ikev1
card crypto mymap 86400 seconds, 1 lifetime of security association set
map mymap 1 set security-association life crypto kilobytes 4608000
map mymap 100-isakmp ipsec crypto dynamic dynmap
mymap outside crypto map interface
crypto isakmp identity address
Crypto isakmp nat-traversal 30
Crypto ikev1 allow outside
IKEv1 crypto ipsec-over-tcp port 10000
IKEv1 crypto policy 5
preshared authentication
3des encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 10
preshared authentication
3des encryption
sha hash
Group 1
life 86400
IKEv1 crypto policy 50
preshared authentication
the Encryption
md5 hash
Group 2
life 86400
IKEv1 crypto policy 60
preshared authentication
aes-256 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 70
preshared authentication
aes-256 encryption
sha hash
Group 1
life 86400
IKEv1 crypto policy 90
preshared authentication
aes encryption
sha hash
Group 2
life 86400
Telnet timeout 5
Console timeout 0
management-access inside
a basic threat threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
WebVPN
internal BACKDOORVPN group policy
BACKDOORVPN group policy attributes
value of VPN-filter 11
Ikev1 VPN-tunnel-Protocol
Split-tunnel-policy tunnelall
BH.UK value by default-field
type tunnel-group BACKDOORVPN remote access
attributes global-tunnel-group BACKDOORVPN
address pool Admin_Pool
Group Policy - by default-BACKDOORVPN
IPSec-attributes tunnel-group BACKDOORVPN
IKEv1 pre-shared-key *.
tunnel-group x.x.x.x type ipsec-l2l
tunnel-group ipsec-attributes x.x.x.x
IKEv1 pre-shared-key *.
!
class-map inspection_default
match default-inspection-traffic
!
!
type of policy-card inspect dns preset_dns_map
parameters
maximum message length automatic of customer
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the preset_dns_map dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
inspect the rsh
inspect the rtsp
inspect esmtp
inspect sqlnet
inspect the skinny
inspect sunrpc
inspect xdmcp
inspect the sip
inspect the netbios
inspect the tftp
Review the ip options
!
global service-policy global_policy
Excellent.
Evaluate the useful ticket.
Thank you
Rizwan James
-
I tried to restart, tried unplugging the unit for a few minutes and commissioning, try a full restore. Nothing solves the problem.
Curiously, I can connect to my ITunes account successfully each time.
But when I then connecting to ICloud, he asked my password (saving my user id when I connected successfully in ITunes), then it asks to send a verification code to one of my devices (because I enabled two-step verification, and so it seems at this stage to be communicating correctly with the server)-then when I click on enter it instantly evokes a message...
Unable to connect
Could not communicate with the server
For more information, visit apple.com/support/icloud.
I also tried logging in ICloud before connecting to ITunes, but get the same error message. ICloud works on all my other devices.
Any suggestions? Thanks for your considered
What version of ATV do you use? This is crucial because they are all running different software.
Try your Apple of a browser logging and disabling two-step verification ID. Then your login the ATV and restore in two steps.
-
Cannot ping inside the ASA from the inside interface
Don't know what I did wrong... appreciate any help
Here is the page layout
laptop--> cisco 3750 switch--> ASA5505 firewall--> future VPN tunnel
Laptop, switch interface VLAN and inside the ASA are all in the same subnet
Switch and ASA have all interfaces local network VIRTUAL 52 (the subnet in question), except for the external interface
-----------------
This is the problem
laptop getting ip addressing and def GW via DHCP from the firewall
switch and FW can ping each other without problem
FW can't ping, still gets the DHCP scope.
Thank you
Dave
Hello
How did you setup?
The laptop is connected to a port of the 3750 (VLAN 52).
The connection between the 3750 and the SAA is a chest or a link L3?
If the 3750 has a SVI belonging to VLAN52, you can ping from the correct PC? As well as the ASA?
Federico.
-
Cisco ASA 5520 cannot ping between VPN Tunnels
I have the main site and sites A and B. A to connect to the hand and B connects to the main. I can ping from A hand and has for main. I can ping from main to B and B to main. However, I can not ping from A to B. A and B are sonicwall 2040 and main is a 5520. The question should not be with the 5520 none allowing traffic between the two VPN Tunnels, but I can't understand why it does not work. Can someone give an idea on that? Thanks in advance.
Hello
I see that you use ASDM. Always makes my eyes bleed when I need to look at the DM_INLINE of named objects and try to make sense the CLI format
Seems to me that there are problems with the NAT.
If you don't mind a small break between the main Site and remote locations, I'd say changing some follows the NAT configuration
Remove old
no nat source (indoor, outdoor) public static DM_INLINE_NETWORK_9 DM_INLINE_NETWORK_9 DM_INLINE_NETWORK_10 DM_INLINE_NETWORK_10 non-proxy-arp-search of route static destination
no nat source (indoor, outdoor) public static DM_INLINE_NETWORK_11 DM_INLINE_NETWORK_11 DM_INLINE_NETWORK_12 DM_INLINE_NETWORK_12 non-proxy-arp-search of route static destination
Add a new
object-group network NETWORK-2790
object-network 10.217.0.0 255.255.255.0
object-network 10.217.1.0 255.255.255.0
object-group network NETWORK-3820
object-network 10.216.0.0 255.255.255.0
object-network 10.216.1.0 255.255.255.0
object-group network NETWORK-COLO
object-net 10.8.0.0 255.255.255.0
destination of NETWORK of NETWORK-2790-2790 static NAT (outside, outside) static source NETWORK - 3820 - 3820
NAT static destination of NETWORK of NETWORK-COLO-COLO (indoor, outdoor) static source NETWORK - 2790 - 2790
NAT static destination of NETWORK of NETWORK-COLO-COLO (indoor, outdoor) static source NETWORK - 3820 - 3820
The first new line of configuring NAT manages the NAT0 configuration for traffic between SiteA and SiteB. The following configurations of NAT 2 manage the NAT0 for traffic between the main Site - hand Site SiteA - SiteB
-Jouni
-
This isn't a matter of McAfee as I talk with them and we turned off the coast of McAfee and the remins still question
Type of topic: addons< enter > in the address bar to open the Add-on Manager.
Access key; < Control >(Mac: < command >) < shift > has)On the left side of the page, select Plugins.
Make sure that the ones you want to use is on Ask or Allow.Go to the web page. Once the page loads, mouse to the address bar
and left click the icon. A window to display information of site should
developed. Select more information. Now select permissions. In the
menu, make sure that those you want to use is on Ask or Allow. -
VPN connection is established but cannot ping subnet
Hello, I have a 851 router that I'm trying to learn with, I have a config of work that makes me online and has a basic firewall and dhcp for clients. Then, I wanted to add a VPN using the 851 and the Cisco VPN client.
Using this tutorial "http://www.cisco.com/en/US/customer/products/sw/secursw/ps5318/products_configuration_example09186a00806ad10e.shtml."
I was able to get partially to my goal as I can establish a vpn and it shows me 192.168.1.0 as the route secure, but I don't ping or communicate with anything with in the 192.168.1.1 network.
Try this one too.
Instead of using access-list in declaration of NAT, use the route map and see if it solves the problem.
1 deny traffic Ipsec in NAT access list.
access-list 120 refuse 192.168.1.0 0.0.0.255 192.168.2.0 0.0.0.255
access-list 120 allow 192.168.1.0 0.0.0 all
2. create a roadmap
sheep allowed 10 route map
corresponds to the IP 120
3. no nat ip within the source list 1 interface FastEthernet4 overload
4 ip nat inside source map route sheep interface FastEthernet4 overload
5 disable the ip nat translation *.
Then check.
HTH
Sangaré
-
AnyConnect users can access internal network
Hello!
Just sat up a new Anyconnect VPN solution for a customer. It works almost perfect.
Anyconnect users can reach the internal network storage. The anyconnect users can access the internet, but nothing on the network internal.
(Deleted all the passwords and public IP addresses)
ASA 4,0000 Version 1
!
ciscoasa hostname
names of
!
interface Ethernet0/0
switchport access vlan 2
!
interface Ethernet0/1
!
interface Ethernet0/2
!
interface Ethernet0/3
!
interface Ethernet0/4
!
interface Ethernet0/5
!
interface Ethernet0/6
!
interface Ethernet0/7
!
interface Vlan1
nameif inside
security-level 100
IP 192.168.9.1 255.255.255.0
!
interface Vlan2
nameif outside
security-level 0
IP address
!
passive FTP mode
DNS domain-lookup outside
DNS server-group DefaultDNS
Server name 213.80.98.2
Server name 213.80.101.3
network obj_any object
subnet 0.0.0.0 0.0.0.0
access-list SHEEP extended ip 192.168.9.0 allow 255.255.255.0 192.168.9.0 255.255.255.0
AnyConnect_Client_Local_Print deny ip extended access list a whole
AnyConnect_Client_Local_Print list extended access permit tcp any any eq lpd
Note AnyConnect_Client_Local_Print of access list IPP: Internet Printing Protocol
AnyConnect_Client_Local_Print list extended access permit tcp any any eq 631
print the access-list AnyConnect_Client_Local_Print Note Windows port
AnyConnect_Client_Local_Print list extended access permit tcp any any eq 9100
access-list AnyConnect_Client_Local_Print mDNS Note: multicast DNS protocol
AnyConnect_Client_Local_Print list extended access permit udp any host 224.0.0.251 eq 5353
AnyConnect_Client_Local_Print of access list LLMNR Note: link Local Multicast Name Resolution protocol
AnyConnect_Client_Local_Print list extended access permit udp any host 224.0.0.252 eq 5355
Note access list TCP/NetBIOS protocol AnyConnect_Client_Local_Print
AnyConnect_Client_Local_Print list extended access permit tcp any any eq 137
AnyConnect_Client_Local_Print list extended access udp allowed any any eq netbios-ns
pager lines 24
Enable logging
logging of debug asdm
Within 1500 MTU
Outside 1500 MTU
mask 192.168.9.50 - 192.168.9.80 255.255.255.0 IP local pool SSLClientPool
ICMP unreachable rate-limit 1 burst-size 1
don't allow no asdm history
ARP timeout 14400
NAT (inside, outside) source Dynamics one interface
!
network obj_any object
NAT dynamic interface (indoor, outdoor)
Route outside 0.0.0.0 0.0.0.0 1
Timeout xlate 03:00
Pat-xlate timeout 0:00:30
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
Floating conn timeout 0:00:00
dynamic-access-policy-registration DfltAccessPolicy
identity of the user by default-domain LOCAL
AAA authentication enable LOCAL console
AAA authentication http LOCAL console
LOCAL AAA authentication serial console
the ssh LOCAL console AAA authentication
AAA authentication LOCAL telnet console
Enable http server
http 192.168.9.0 255.255.255.0 inside
http 0.0.0.0 0.0.0.0 inside
http 0.0.0.0 0.0.0.0 outdoors
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown warmstart of cold start
Telnet timeout 5
SSH timeout 5
SSH group dh-Group1-sha1 key exchange
Console timeout 0
dhcpd outside auto_config
!
dhcpd address 192.168.9.2 - 192.168.9.33 inside
dhcpd ip interface 192.168.9.1 option 3 inside
!
a basic threat threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
WebVPN
allow outside
AnyConnect image disk0:/anyconnect-win-2.5.3046-k9.pkg 1
AnyConnect enable
tunnel-group-list activate
internal SSLClitentPolicy group strategy
internal SSLClientPolicy group strategy
attributes of Group Policy SSLClientPolicy
value of server DNS 192.168.9.5
client ssl-VPN-tunnel-Protocol
the address value SSLClientPool pools
attributes of Group Policy DfltGrpPolicy
VPN-tunnel-Protocol ikev1, ikev2 ssl clientless ssl ipsec l2tp client
VPN Tunnel-group type remote access
type tunnel-group SSLClientProfile remote access
attributes global-tunnel-group SSLClientProfile
Group Policy - by default-SSLClientPolicy
tunnel-group SSLClientProfile webvpn-attributes
enable SSLVPNClient group-alias
!
class-map inspection_default
match default-inspection-traffic
!
!
type of policy-card inspect dns preset_dns_map
parameters
maximum message length automatic of customer
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the preset_dns_map dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
inspect the rsh
inspect the rtsp
inspect esmtp
inspect sqlnet
inspect the skinny
inspect sunrpc
inspect xdmcp
inspect the sip
inspect the netbios
inspect the tftp
Review the ip options
!
global service-policy global_policy
context of prompt hostname
no remote anonymous reporting call
Cryptochecksum:6a58e90dc61dfbf7ba15e059e5931609
: end
Looks like you got the permit vpn sysopt disable to enable:
Sysopt connection permit VPN
Also remove the dynamic NAT depending on whether you have already configured under the NAT object:
No source (indoor, outdoor) nat Dynamics one interface
Then 'clear xlate' once again and let us know if it works now.
-
How many users can connect to Apple TV at the same time?
How many users can connect to Apple TV at the same time?
Your question is a little vague, what do you mean by "users that connect to AppleTV?
-
How many users can connect to a hotspot of the iPhone 6?
How many users can connect to a hotspot of the iPhone 6?
I think it's 5.
-
Dear all,
I intend to install on Server 2008 SBS Active Directory domain controller. In this session, I would like to know the client users can connect to the SBS server or not. If CAN, I want to know the steps & solutions on this answer and if NOT, why the clients could not connect to the SBS server.
Server 2008 SBS can also be installed on the sequence of steps:
SBS 2008 (AD, Exchange Server, SQL 2005 or 08, CRM4.0). It depends on the situation of the organization.I really want to know that, if we install steps on SBS 2008 above, can clients connect to the server?
Kind regards
Tun Aung KyawHi Geraldine Tun.
Your question is more complex than what is generally answered in the Microsoft Answers forums. It is better suited for the IT Pro TechNet public. Please post your question in the TechNet Windows Server forum.
http://social.technet.Microsoft.com/forums/en-us/category/WindowsServer
-
How to create a Web site that users can connect to?
Hey guys
How to create a Web site that users can connect to?
How to create a site that users can connect to with steam, facebook, twitter, etc...
See this discussion where a similar topic was discussed.
Login using Muse and British Colombia page
Thank you
Preran
Maybe you are looking for
-
Serial RS232 between existing Instrument and reading software provider
Hello. I have an instrument with software supplier for the acquisition of data from the instrument to a PC through serial RS-232 communication. I would like to acquire data in LabVIEW instead of via the provider software. The seller has given virt
-
My scanner seems to work, but all the pages in the output file are completely black. Interestingly, auto-feed scanning and flat options seem to work. Scanning preview shows a representation of the document when you use the flat, but the resulting sca
-
How to create PDF with PDF Exaprom bookmarks?
IText in ACTION by Bruno Lowagie reading, you can create bookmarks for a PDF automatically by adding chapters. Is it possible to do it with Exaprom. I can just mod a paragraph add so it adds a chapter? I love Exaprom. Great package! Norm
-
Impossible to get Oregon Trail 2 to install on my Windows 7 PC
Whenever I try to install the track to the Oregon 2 (from the CD), it gives me an error message indicating that it is not compatible. I tried to change the compatibility mode, and it didn't work. Any suggestions? I can get the first screen to appear
-
I received this email at the end of May and I want to come again.