Cisco ASA 8.4 (3) remote access VPN - client connects but cannot access inside the network

I have problems to access the resources within the network when connecting with the Cisco VPN client for a version of 8.4 (3) operation of the IOS Cisco ASA 5510. I tried all new NAT 8.4 orders but cannot access the network interior. I can see traffic in newspapers when ping. I can only assume I have NAT evil or it's because the inside interface of the ASA is on the 24th of the same subnet as the network interior? Please see config below, any suggestion would be appreciated. I configured a VPN site to another in this same 5510 and it works well

Thank you

interface Ethernet0/0

Speed 100

full duplex

nameif outside

security-level 0

IP x.x.x.x 255.255.255.240

!

interface Ethernet0/1

Speed 100

full duplex

nameif inside

security-level 100

IP 10.88.10.254 255.255.255.0

!

interface Management0/0

Shutdown

nameif management

security-level 0

no ip address

!

permit same-security-traffic inter-interface

permit same-security-traffic intra-interface

network of the PAT_to_Outside_ClassA object

10.88.0.0 subnet 255.255.0.0

network of the PAT_to_Outside_ClassB object

subnet 172.16.0.0 255.240.0.0

network of the PAT_to_Outside_ClassC object

Subnet 192.168.0.0 255.255.240.0

network of the LocalNetwork object

10.88.0.0 subnet 255.255.0.0

network of the RemoteNetwork1 object

Subnet 192.168.0.0 255.255.0.0

network of the RemoteNetwork2 object

172.16.10.0 subnet 255.255.255.0

network of the RemoteNetwork3 object

10.86.0.0 subnet 255.255.0.0

network of the RemoteNetwork4 object

10.250.1.0 subnet 255.255.255.0

network of the NatExempt object

10.88.10.0 subnet 255.255.255.0

the Site_to_SiteVPN1 object-group network

object-network 192.168.4.0 255.255.254.0

object-network 172.16.10.0 255.255.255.0

object-network 10.0.0.0 255.0.0.0

outside_access_in deny ip extended access list a whole

inside_access_in of access allowed any ip an extended list

11 extended access-list allow ip 10.250.1.0 255.255.255.0 any

outside_1_cryptomap to access extended list ip 10.88.0.0 255.255.0.0 allow object-group Site_to_SiteVPN1

mask 10.250.1.1 - 10.250.1.254 255.255.255.0 IP local pool Admin_Pool

NAT static NatExempt NatExempt of the source (indoor, outdoor)

NAT (inside, outside) static source any any static destination RemoteNetwork4 RemoteNetwork4-route search

NAT static LocalNetwork LocalNetwork destination (indoor, outdoor) static source RemoteNetwork1 RemoteNetwork1

NAT static LocalNetwork LocalNetwork destination (indoor, outdoor) static source RemoteNetwork2 RemoteNetwork2

NAT static LocalNetwork LocalNetwork destination (indoor, outdoor) static source RemoteNetwork3 RemoteNetwork3

NAT (inside, outside) static source LocalNetwork LocalNetwork static destination RemoteNetwork4 RemoteNetwork4-route search

!

network of the PAT_to_Outside_ClassA object

NAT dynamic interface (indoor, outdoor)

network of the PAT_to_Outside_ClassB object

NAT dynamic interface (indoor, outdoor)

network of the PAT_to_Outside_ClassC object

NAT dynamic interface (indoor, outdoor)

Access-group outside_access_in in interface outside

inside_access_in access to the interface inside group

Route outside 0.0.0.0 0.0.0.0 x.x.x.x 1

dynamic-access-policy-registration DfltAccessPolicy

Sysopt connection timewait

Service resetoutside

Crypto ipsec transform-set ikev1 ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac

Crypto ipsec transform-set ikev1 ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac

Crypto ipsec transform-set ikev1 ESP-AES-192-SHA esp-aes-192 esp-sha-hmac

Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-esp - aes esp-md5-hmac

Crypto ipsec transform-set esp-ikev1 esp-md5-hmac bh-series

Crypto ipsec transform-set ikev1 esp ESP-DES-MD5-esp-md5-hmac

Crypto ipsec transform-set ikev1 ESP-3DES-MD5-esp-3des esp-md5-hmac

Crypto ipsec transform-set ikev1 ESP-DES-SHA esp - esp-sha-hmac

Crypto ipsec transform-set ikev1 ESP-AES-128-SHA aes - esp esp-sha-hmac

Crypto ipsec transform-set ikev1 ESP-AES-256-SHA esp-aes-256 esp-sha-hmac

Crypto ipsec transform-set ikev1 SHA-ESP-3DES esp-3des esp-sha-hmac

Crypto-map dynamic dynmap 10 set pfs

Crypto-map dynamic dynmap 10 set transform-set bh - set ikev1

life together - the association of security crypto dynamic-map dynmap 10 28800 seconds

Crypto-map dynamic dynmap 10 kilobytes of life together - the association of safety 4608000

Crypto-map dynamic dynmap 10 the value reverse-road

card crypto mymap 1 match address outside_1_cryptomap

card crypto mymap 1 set counterpart x.x.x.x

card crypto mymap 1 set transform-set ESP-AES-256-SHA ikev1

card crypto mymap 86400 seconds, 1 lifetime of security association set

map mymap 1 set security-association life crypto kilobytes 4608000

map mymap 100-isakmp ipsec crypto dynamic dynmap

mymap outside crypto map interface

crypto isakmp identity address

Crypto isakmp nat-traversal 30

Crypto ikev1 allow outside

IKEv1 crypto ipsec-over-tcp port 10000

IKEv1 crypto policy 5

preshared authentication

3des encryption

sha hash

Group 2

life 86400

IKEv1 crypto policy 10

preshared authentication

3des encryption

sha hash

Group 1

life 86400

IKEv1 crypto policy 50

preshared authentication

the Encryption

md5 hash

Group 2

life 86400

IKEv1 crypto policy 60

preshared authentication

aes-256 encryption

sha hash

Group 2

life 86400

IKEv1 crypto policy 70

preshared authentication

aes-256 encryption

sha hash

Group 1

life 86400

IKEv1 crypto policy 90

preshared authentication

aes encryption

sha hash

Group 2

life 86400

Telnet timeout 5

Console timeout 0

management-access inside

a basic threat threat detection

Statistics-list of access threat detection

no statistical threat detection tcp-interception

WebVPN

internal BACKDOORVPN group policy

BACKDOORVPN group policy attributes

value of VPN-filter 11

Ikev1 VPN-tunnel-Protocol

Split-tunnel-policy tunnelall

BH.UK value by default-field

type tunnel-group BACKDOORVPN remote access

attributes global-tunnel-group BACKDOORVPN

address pool Admin_Pool

Group Policy - by default-BACKDOORVPN

IPSec-attributes tunnel-group BACKDOORVPN

IKEv1 pre-shared-key *.

tunnel-group x.x.x.x type ipsec-l2l

tunnel-group ipsec-attributes x.x.x.x

IKEv1 pre-shared-key *.

!

class-map inspection_default

match default-inspection-traffic

!

!

type of policy-card inspect dns preset_dns_map

parameters

maximum message length automatic of customer

message-length maximum 512

Policy-map global_policy

class inspection_default

inspect the preset_dns_map dns

inspect the ftp

inspect h323 h225

inspect the h323 ras

inspect the rsh

inspect the rtsp

inspect esmtp

inspect sqlnet

inspect the skinny

inspect sunrpc

inspect xdmcp

inspect the sip

inspect the netbios

inspect the tftp

Review the ip options

!

global service-policy global_policy

Advertisement

Excellent.

Evaluate the useful ticket.

Thank you

Rizwan James

Tags: Cisco Security

Similar Questions

  • Remote access VPN client to connect but cannot ping inside the host, after that split tunnel is activated (config-joint)

    Hello

    I don't know what could be held, vpn users can ping to the outside and inside of the Cisco ASA interface but can not connect to servers or servers within the LAN ping.

    is hell config please kindly and I would like to know what might happen.

    hostname horse

    domain evergreen.com

    activate 2KFQnbNIdI.2KYOU encrypted password

    2KFQnbNIdI.2KYOU encrypted passwd

    names of

    ins-guard

    !

    interface GigabitEthernet0/0

    LAN description

    nameif inside

    security-level 100

    192.168.200.1 IP address 255.255.255.0

    !

    interface GigabitEthernet0/1

    Description CONNECTION_TO_FREEMAN

    nameif outside

    security-level 0

    IP 196.1.1.1 255.255.255.248

    !

    interface GigabitEthernet0/2

    Description CONNECTION_TO_TIGHTMAN

    nameif backup

    security-level 0

    IP 197.1.1.1 255.255.255.248

    !

    interface GigabitEthernet0/3

    Shutdown

    No nameif

    no level of security

    no ip address

    !

    interface Management0/0

    Shutdown

    No nameif

    no level of security

    no ip address

    management only

    !

    boot system Disk0: / asa844-1 - k8.bin

    boot system Disk0: / asa707 - k8.bin

    passive FTP mode

    clock timezone WAT 1

    DNS server-group DefaultDNS

    domain green.com

    network of the NETWORK_OBJ_192.168.2.0_25 object

    Subnet 192.168.2.0 255.255.255.128

    network of the NETWORK_OBJ_192.168.202.0_24 object

    192.168.202.0 subnet 255.255.255.0

    network obj_any object

    subnet 0.0.0.0 0.0.0.0

    the DM_INLINE_NETWORK_1 object-group network

    object-network 192.168.200.0 255.255.255.0

    object-network 192.168.202.0 255.255.255.0

    the DM_INLINE_NETWORK_2 object-group network

    object-network 192.168.200.0 255.255.255.0

    object-network 192.168.202.0 255.255.255.0

    access-list extended INSIDE_OUT allow ip 192.168.202.0 255.255.255.0 any

    access-list extended INSIDE_OUT allow ip 192.168.200.0 255.255.255.0 any

    Access extensive list permits all ip a OUTSIDE_IN

    gbnlvpntunnel_splitTunnelAcl standard access list allow 192.168.200.0 255.255.255.0

    standard access list gbnlvpntunnel_splitTunnelAcl allow 192.168.202.0 255.255.255.0

    gbnlvpntunnell_splitTunnelAcl standard access list allow 192.168.200.0 255.255.255.0

    standard access list gbnlvpntunnell_splitTunnelAcl allow 192.168.202.0 255.255.255.0

    pager lines 24

    Enable logging

    asdm of logging of information

    Within 1500 MTU

    Outside 1500 MTU

    backup of MTU 1500

    mask of local pool VPNPOOL 192.168.2.0 - 192.168.2.100 IP 255.255.255.0

    no failover

    ICMP unreachable rate-limit 1 burst-size 1

    ASDM image disk0: / asdm-645 - 206.bin

    don't allow no asdm history

    ARP timeout 14400

    NAT (inside, outside) static source NETWORK_OBJ_192.168.202.0_24 NETWORK_OBJ_192.168.202.0_24 NETWORK_OBJ_192.168.2.0_25 NETWORK_OBJ_192.168.2.0_25 non-proxy-arp-search of route static destination

    NAT (inside, backup) static source NETWORK_OBJ_192.168.202.0_24 NETWORK_OBJ_192.168.202.0_24 NETWORK_OBJ_192.168.2.0_25 NETWORK_OBJ_192.168.2.0_25 non-proxy-arp-search of route static destination

    NAT (inside, outside) static source DM_INLINE_NETWORK_1 DM_INLINE_NETWORK_1 NETWORK_OBJ_192.168.2.0_25 NETWORK_OBJ_192.168.2.0_25 non-proxy-arp-search of route static destination

    NAT (inside, backup) static source DM_INLINE_NETWORK_2 DM_INLINE_NETWORK_2 NETWORK_OBJ_192.168.2.0_25 NETWORK_OBJ_192.168.2.0_25 non-proxy-arp-search of route static destination

    !

    network obj_any object

    dynamic NAT interface (inside, backup)

    Access-group interface inside INSIDE_OUT

    Access-group OUTSIDE_IN in interface outside

    Route outside 0.0.0.0 0.0.0.0 196.1.1.2 1 track 10

    Route outside 0.0.0.0 0.0.0.0 197.1.1.2 254

    Timeout xlate 03:00

    Pat-xlate timeout 0:00:30

    Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02

    Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00

    Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00

    Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute

    timeout tcp-proxy-reassembly 0:01:00

    Floating conn timeout 0:00:00

    dynamic-access-policy-registration DfltAccessPolicy

    identity of the user by default-domain LOCAL

    Enable http server

    http 192.168.200.0 255.255.255.0 inside

    http 192.168.202.0 255.255.255.0 inside

    No snmp server location

    No snmp Server contact

    Server enable SNMP traps snmp authentication linkup, linkdown cold start

    monitor SLA 100

    type echo protocol ipIcmpEcho 212.58.244.71 interface outside

    Timeout 3000

    frequency 5

    monitor als 100 calendar life never start-time now

    Crypto ipsec transform-set ikev1 ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac

    Crypto ipsec transform-set ikev1 ESP-DES-SHA esp - esp-sha-hmac

    Crypto ipsec transform-set ikev1 SHA-ESP-3DES esp-3des esp-sha-hmac

    Crypto ipsec transform-set ikev1 esp ESP-DES-MD5-esp-md5-hmac

    Crypto ipsec transform-set ikev1 ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac

    Crypto ipsec transform-set ikev1 ESP-3DES-MD5-esp-3des esp-md5-hmac

    Crypto ipsec transform-set ikev1 ESP-AES-256-SHA esp-aes-256 esp-sha-hmac

    Crypto ipsec transform-set ikev1 ESP-AES-128-SHA aes - esp esp-sha-hmac

    Crypto ipsec transform-set ikev1 ESP-AES-192-SHA esp-aes-192 esp-sha-hmac

    Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-esp - aes esp-md5-hmac

    crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 pfs Group1 set

    crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 define ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5

    outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP

    outside_map interface card crypto outside

    backup_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP

    backup of crypto backup_map interface card

    Crypto ikev1 allow outside

    Crypto ikev1 enable backup

    IKEv1 crypto policy 10

    authentication crack

    aes-256 encryption

    sha hash

    Group 2

    life 86400

    IKEv1 crypto policy 20

    authentication rsa - sig

    aes-256 encryption

    sha hash

    Group 2

    life 86400

    IKEv1 crypto policy 30

    preshared authentication

    aes-256 encryption

    sha hash

    Group 2

    life 86400

    IKEv1 crypto policy 40

    authentication crack

    aes-192 encryption

    sha hash

    Group 2

    life 86400

    IKEv1 crypto policy 50

    authentication rsa - sig

    aes-192 encryption

    sha hash

    Group 2

    life 86400

    IKEv1 crypto policy 60

    preshared authentication

    aes-192 encryption

    sha hash

    Group 2

    life 86400

    IKEv1 crypto policy 70

    authentication crack

    aes encryption

    sha hash

    Group 2

    life 86400

    IKEv1 crypto policy 80

    authentication rsa - sig

    aes encryption

    sha hash

    Group 2

    life 86400

    IKEv1 crypto policy 90

    preshared authentication

    aes encryption

    sha hash

    Group 2

    life 86400

    IKEv1 crypto policy 100

    authentication crack

    3des encryption

    sha hash

    Group 2

    life 86400

    IKEv1 crypto policy 110

    authentication rsa - sig

    3des encryption

    sha hash

    Group 2

    life 86400

    IKEv1 crypto policy 120

    preshared authentication

    3des encryption

    sha hash

    Group 2

    life 86400

    IKEv1 crypto policy 130

    authentication crack

    the Encryption

    sha hash

    Group 2

    life 86400

    IKEv1 crypto policy 140

    authentication rsa - sig

    the Encryption

    sha hash

    Group 2

    life 86400

    IKEv1 crypto policy 150

    preshared authentication

    the Encryption

    sha hash

    Group 2

    life 86400

    !

    track 10 rtr 100 accessibility

    Telnet 192.168.200.0 255.255.255.0 inside

    Telnet 192.168.202.0 255.255.255.0 inside

    Telnet timeout 5

    SSH 192.168.202.0 255.255.255.0 inside

    SSH 192.168.200.0 255.255.255.0 inside

    SSH 0.0.0.0 0.0.0.0 outdoors

    SSH timeout 15

    SSH group dh-Group1-sha1 key exchange

    Console timeout 0

    management-access inside

    a basic threat threat detection

    Statistics-list of access threat detection

    no statistical threat detection tcp-interception

    WebVPN

    internal group vpntunnel strategy

    Group vpntunnel policy attributes

    Ikev1 VPN-tunnel-Protocol

    Split-tunnel-policy tunnelspecified

    value of Split-tunnel-network-list vpntunnel_splitTunnelAcl

    field default value green.com

    internal vpntunnell group policy

    attributes of the strategy of group vpntunnell

    Ikev1 VPN-tunnel-Protocol

    Split-tunnel-policy tunnelspecified

    value of Split-tunnel-network-list gbnlvpntunnell_splitTunnelAcl

    field default value green.com

    Green user name encrypted BoEFKkDtbnX5Uy1Q privilege 15 password

    attributes of user name THE

    VPN-group-policy gbnlvpn

    tunnel-group vpntunnel type remote access

    tunnel-group vpntunnel General attributes

    address VPNPOOL pool

    strategy-group-by default vpntunnel

    tunnel-group vpntunnel ipsec-attributes

    IKEv1 pre-shared-key *.

    type tunnel-group vpntunnell remote access

    tunnel-group vpntunnell General-attributes

    address VPNPOOL2 pool

    Group Policy - by default-vpntunnell

    vpntunnell group of tunnel ipsec-attributes

    IKEv1 pre-shared-key *.

    !

    class-map inspection_default

    match default-inspection-traffic

    !

    !

    type of policy-card inspect dns migrated_dns_map_1

    parameters

    maximum message length automatic of customer

    message-length maximum 512

    Policy-map global_policy

    class inspection_default

    inspect the migrated_dns_map_1 dns

    inspect the ftp

    inspect h323 h225

    inspect the h323 ras

    inspect the rsh

    inspect the rtsp

    inspect esmtp

    inspect sqlnet

    inspect the skinny

    inspect sunrpc

    inspect xdmcp

    inspect the sip

    inspect the netbios

    inspect the tftp

    Review the ip options

    !

    global service-policy global_policy

    context of prompt hostname

    no remote anonymous reporting call

    call-home

    Profile of CiscoTAC-1

    no active account

    http https://tools.cisco.com/its/service/oddce/services/DDCEService destination address

    email address of destination [email protected] / * /

    destination-mode http transport

    Subscribe to alert-group diagnosis

    Subscribe to alert-group environment

    Subscribe to alert-group monthly periodic inventory

    monthly periodicals to subscribe to alert-group configuration

    daily periodic subscribe to alert-group telemetry

    Cryptochecksum:7c1b1373bf2e2c56289b51b8dccaa565

    Hello

    1 - Please run these commands:

    "crypto isakmp nat-traversal 30.

    "crypto than dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 Road opposite value.

    The main issue here is that you have two roads floating and outside it has a better than backup metric, that's why I added the command 'reverse-road '.

    Please let me know.

    Thank you.

  • VPN IS CONNECTED BUT CANNOT ACCESS THE INTERNAL NETWORK

    I tried to set up a simple customer vpn using this document

    http://www.Cisco.com/en/us/products/sw/secursw/ps2308/products_configuration_example09186a00801e71c0.shtml

    VPN IS CONNECTED BUT CANNOT ACCESS THE INTERNAL NETWORK BEHIND "RA"...

    6.3 (5) PIX version

    interface ethernet0 car

    Auto interface ethernet1

    ethernet0 nameif outside security0

    nameif ethernet1 inside the security100

    activate the encrypted password of VmHKIhnF4Gs5AWk3

    VmHKIhnF4Gs5AWk3 encrypted passwd

    hostname VOIPLABPIX

    domain voicelab.com

    fixup protocol dns-length maximum 512

    fixup protocol ftp 21

    fixup protocol h323 h225 1720

    fixup protocol h323 ras 1718-1719

    fixup protocol http 80

    fixup protocol they 389

    fixup protocol rsh 514

    fixup protocol rtsp 554

    fixup protocol sip 5060

    fixup protocol sip udp 5060

    fixup protocol 2000 skinny

    fixup protocol smtp 25

    fixup protocol sqlnet 1521

    fixup protocol tftp 69

    names of

    access-list 101 permit ip 172.10.2.0 255.255.255.0 172.10.3.0 255.255.255.0

    access-list 101 permit ip 172.10.1.0 255.255.255.0 172.10.3.0 255.255.255.0

    access-list 102 permit ip 172.10.2.0 255.255.255.0 172.10.3.0 255.255.255.0

    access-list 102 permit ip 172.10.1.0 255.255.255.0 172.10.3.0 255.255.255.0

    pager lines 24

    Outside 1500 MTU

    Within 1500 MTU

    IP address outside 208.x.x.11 255.255.255.0

    IP address inside 172.10.2.2 255.255.255.0

    alarm action IP verification of information

    alarm action attack IP audit

    IP local pool voicelabpool 172.10.3.100 - 172.10.3.254

    history of PDM activate

    ARP timeout 14400

    NAT (inside) - 0 102 access list

    Route outside 0.0.0.0 0.0.0.0 208.x.x.11 1

    Route inside 172.10.1.0 255.255.255.0 172.10.2.1 1

    Timeout xlate 03:00

    Timeout conn 01:00 half-closed 0:10:00 udp 0: CPP 02:00 0:10:00 01:00 h225

    H323 timeout 0:05:00 mgcp 0: sip from 05:00 0:30:00 sip_media 0:02:00

    Sip timeout - disconnect 0:02:00 prompt Protocol sip-0: 03:00

    Timeout, uauth 0:05:00 absolute

    GANYMEDE + Protocol Ganymede + AAA-server

    AAA-server GANYMEDE + 3 max-failed-attempts

    AAA-server GANYMEDE + deadtime 10

    RADIUS Protocol RADIUS AAA server

    AAA-server RADIUS 3 max-failed-attempts

    AAA-RADIUS deadtime 10 Server

    AAA-server local LOCAL Protocol

    Enable http server

    http 172.0.0.0 255.0.0.0 inside

    http 0.0.0.0 0.0.0.0 inside

    No snmp server location

    No snmp Server contact

    SNMP-Server Community public

    No trap to activate snmp Server

    enable floodguard

    Permitted connection ipsec sysopt

    Crypto ipsec transform-set esp-aes-256 trmset1, esp-sha-hmac

    Crypto-map dynamic map2 10 set transform-set trmset1

    map map1 10 ipsec-isakmp crypto dynamic map2

    client authentication card crypto LOCAL map1

    map1 outside crypto map interface

    ISAKMP allows outside

    ISAKMP identity address

    part of pre authentication ISAKMP policy 10

    ISAKMP policy 10 encryption aes-256

    ISAKMP policy 10 sha hash

    10 2 ISAKMP policy group

    ISAKMP life duration strategy 10 86400

    vpngroup address voicelabpool pool cuclab

    vpngroup dns 204.x.x.10 Server cuclab

    vpngroup cuclab by default-field voicelab.com

    vpngroup split tunnel 101 cuclab

    vpngroup idle 1800 cuclab-time

    vpngroup password cuclab *.

    Telnet timeout 5

    SSH 208.x.x.11 255.255.255.255 outside

    SSH 0.0.0.0 0.0.0.0 outdoors

    SSH 172.10.1.2 255.255.255.255 inside

    SSH timeout 60

    Console timeout 0

    username labadmin jNEF0yoDIDCsaoVQ encrypted password privilege 2

    Terminal width 80

    Cryptochecksum:b03a349e1ac9e6022432523bbb54504b

    : end

    Try to turn on NAT - T

    PIX (config) #isakmp nat-traversal 20

    http://www.Cisco.com/en/us/products/ps6120/products_tech_note09186a00807e0aca.shtml#Solution1

    HTH

  • ASA 5505 VPN established, cannot access inside the network

    Hi, I recently got an ASA 5505, and I spent weeks to find a way to set up a VPN on it.

    After a few days, I finally found the solution to connect to my ASA with a VPN client yet and cannot access devices that are connected to the ASA.

    Here is my config:

    ASA Version 8.2 (5)
    !
    hostname asa01
    domain kevinasa01.net
    activate 8Ry2YjIyt7RRXU24 encrypted password
    2KFQnbNIdI.2KYOU encrypted passwd
    names of
    !
    interface Ethernet0/0
    switchport access vlan 2
    !
    interface Ethernet0/1
    !
    interface Ethernet0/2
    !
    interface Ethernet0/3
    switchport access vlan 5
    !
    interface Ethernet0/4
    !
    interface Ethernet0/5
    !
    interface Ethernet0/6
    !
    interface Ethernet0/7
    !
    interface Vlan1
    nameif inside
    security-level 100
    IP 192.168.1.1 255.255.255.0
    !
    interface Vlan2
    nameif outside
    security-level 0
    IP address dhcp setroute
    !
    interface Vlan5
    No nameif
    security-level 50
    IP 172.16.1.1 255.255.255.0
    !
    passive FTP mode
    DNS server-group DefaultDNS
    domain kevinasa01.net
    permit same-security-traffic intra-interface
    Remote_Kevin_splitTunnelAcl list standard access allowed 192.168.1.0 255.255.255.0
    inside_nat0_outbound to access ip 192.168.1.0 scope list allow 255.255.255.0 192.168.254.0 255.255.255.240
    inside_nat0_outbound list of allowed ip extended access all 192.168.254.0 255.255.255.0
    inside_nat0_outbound list of allowed ip extended access entire 192.168.1.0 255.255.255.0
    sheep - in extended Access-list allow IP 192.168.254.0 255.255.255.0 192.168.1.0 255.255.255.0
    access extensive list ip 192.168.254.0 outside_access_in allow 255.255.255.0 any
    access extensive list ip 192.168.254.0 inside_access_in allow 255.255.255.0 any
    pager lines 24
    asdm of logging of information
    Outside 1500 MTU
    Within 1500 MTU
    pool pool 192.168.254.1 - 192.168.254.10 255.255.255.0 IP mask
    ICMP unreachable rate-limit 1 burst-size 1
    don't allow no asdm history
    ARP timeout 14400
    Global 1 interface (outside)
    NAT (outside) 1 192.168.254.0 255.255.255.0
    NAT (inside) 0 access-list sheep - in
    NAT (inside) 1 192.168.1.0 255.255.255.0
    NAT (inside) 1 0.0.0.0 0.0.0.0
    Access-group outside_access_in in interface outside
    Timeout xlate 03:00
    Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
    Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
    Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
    Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
    timeout tcp-proxy-reassembly 0:01:00
    Floating conn timeout 0:00:00
    dynamic-access-policy-registration DfltAccessPolicy
    Enable http server
    http 192.168.1.0 255.255.255.0 inside
    No snmp server location
    No snmp Server contact
    Server enable SNMP traps snmp authentication linkup, linkdown cold start
    Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
    Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac
    Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac
    Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac
    Crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
    Crypto ipsec transform-set ESP-AES-128-MD5-esp - aes esp-md5-hmac
    Crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
    Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac
    Crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
    Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac
    life crypto ipsec security association seconds 28800
    Crypto ipsec kilobytes of life - safety 4608000 association
    crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 pfs Group1 set
    Crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 value transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5
    outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP
    outside_map interface card crypto outside
    crypto ISAKMP allow outside
    crypto ISAKMP policy 10
    preshared authentication
    3des encryption
    sha hash
    Group 2
    life 86400
    Telnet timeout 5
    SSH timeout 5
    Console timeout 0
    management-access inside
    dhcpd outside auto_config
    !
    dhcpd address 192.168.1.5 - 192.168.1.36 inside
    dhcpd allow inside
    !

    a basic threat threat detection
    Statistics-list of access threat detection
    no statistical threat detection tcp-interception
    WebVPN
    internal Remote_Kevin group strategy
    attributes of Group Policy Remote_Kevin
    value of server DNS 192.168.1.12 192.168.1.13
    VPN - connections 3
    Protocol-tunnel-VPN IPSec
    Split-tunnel-policy tunnelspecified
    value of Split-tunnel-network-list Remote_Kevin_splitTunnelAcl
    kevinasa01.NET value by default-field
    username kevin mz6JxJib/sQqvsw9 password encrypted privilege 0
    username kevin attributes
    VPN-group-policy Remote_Kevin
    type tunnel-group Remote_Kevin remote access
    attributes global-tunnel-group Remote_Kevin
    address-pool
    Group Policy - by default-Remote_Kevin
    IPSec-attributes tunnel-group Remote_Kevin
    pre-shared key *.
    !
    class-map inspection_default
    match default-inspection-traffic
    !
    !
    type of policy-card inspect dns preset_dns_map
    parameters
    maximum message length automatic of customer
    message-length maximum 512
    Policy-map global_policy
    class inspection_default
    inspect the preset_dns_map dns
    inspect the ftp
    inspect h323 h225
    inspect the h323 ras
    inspect the rsh
    inspect the rtsp
    inspect esmtp
    inspect sqlnet
    inspect the skinny
    inspect sunrpc
    inspect xdmcp
    inspect the sip
    inspect the netbios
    inspect the tftp
    Review the ip options
    inspect the icmp
    inspect the icmp error
    !
    global service-policy global_policy
    context of prompt hostname
    no remote anonymous reporting call
    Cryptochecksum:2bb1da52d1993eb9b13c2f6dc97c16cd
    : end

    Thank you

    Hello

    I read your message quickly through my cell phone. I don't know why you have spent your config twice. Maybe a typo issue.

    I see the acl sheep in the wrong way. I mean 192.168.254 are your pool VPN and 192.168.1.0 your local LAN.

    The acl must be:

    sheep - in extended access-list permit ip 192.168.1.0 255.255.255.0 192.168.254.0 255.255.255.0

    For nat (inside), you have 2 lines:

    NAT (inside) 1 192.168.1.0 255.255.255.0 ==> it is redundant as the 1 below does the same thing with more networks if there is inside side. You can delete it.
    NAT (inside) 1 0.0.0.0 0.0.0.0

    Why are you doing this nat (outside)?

    NAT (outside) 1 192.168.254.0 255.255.255.0

    Here are the first questions that I have seen by reading through my mobile. Let's change this and let me know. I'll take a look later with a computer (tonight or tomorrow)

    Thank you.

    PS: Please do not forget to rate and score as good response if this solves your problem.

  • PIX: Cisco VPN Client connects but no routing

    Hello

    We have a Cisco PIX 515 with software 7.1 (2). He accepts Cisco VPN Client connections with no problems, but no routing does to internal networks directly connected to the PIX. For example, my PC is affected by the IP 172.16.2.57 and then ping does not respond to internal Windows server 172.16.0.12 or trying to RDP. The most irritating thing is that these attempts are recorded in the system log, but always ended with "SYN timeout", as follows:

    2009-01-06 23:23:01 Local4.Info 217.15.42.214% 302013-6-PIX: built 3315917 for incoming TCP connections (172.16.2.57/1283) outside:172.16.2.57/1283 inside: ALAI2 / 3389 (ALAI2/3389)

    2009-01-06 23:23:31 Local4.Info 217.15.42.214% 302014-6-PIX: TCP connection disassembly 3315917 for outside:172.16.2.57/1283 inside: ALAI2 / 3389 duration 0:00:30 bytes 0 SYN Timeout

    2009-01-06 23:23:31 Local4.Debug 217.15.42.214% 7-PIX-609002: duration of disassembly-outside local host: 172.16.2.57 0:00:30

    We tried to activate and deactivate "nat-control", "permit same-security-traffic inter-interface" and "permit same-security-traffic intra-interface", but the results are the same: the VPN connection is successfully established, but remote clients cannot reach the internal servers.

    I enclose the training concerned in order to understand the problem:

    interface Ethernet0

    Speed 100

    full duplex

    nameif outside

    security-level 0

    IP address xx.yy.zz.tt 255.255.255.240

    !

    interface Ethernet1

    nameif inside

    security-level 100

    172.16.0.1 IP address 255.255.255.0

    !

    access extensive list ip 172.16.0.0 inside_nat0_outbound allow 255.255.255.0 172.16.2.56 255.255.255.248

    !

    access extensive list ip 172.16.0.0 outside_cryptomap_dyn_20 allow 255.255.255.0 172.16.2.56 255.255.255.248

    !

    VPN_client_group_splitTunnelAcl list standard access allowed 172.16.0.0 255.255.255.0

    !

    IP local pool pool_vpn_clientes 172.16.2.57 - 172.16.2.62 mask 255.255.255.248

    !

    NAT-control

    Global xx.yy.zz.tt 12 (outside)

    NAT (inside) 0-list of access inside_nat0_outbound

    NAT (inside) 12 172.16.0.12 255.255.255.255

    !

    internal VPN_clientes group strategy

    attributes of Group Policy VPN_clientes

    xxyyzz.NET value by default-field

    internal VPN_client_group group strategy

    attributes of Group Policy VPN_client_group

    Split-tunnel-policy tunnelspecified

    value of Split-tunnel-network-list VPN_client_group_splitTunnelAcl

    xxyyzz.local value by default-field

    !

    I join all the details of the cryptographic algorithms because the VPN is successfully completed, as I said at the beginning. In addition, routing tables are irrelevant in my opinion, because the inaccessible hosts are directly connected to the internal LAN of the PIX 515.

    Thank you very much.

    can you confirm asa have NAT traversal allow otherwise, activate it in asa and vpn clients try again.

    PIX / ASA 7.1 and earlier versions

    PIX (config) #isakmp nat-traversal 20

    PIX / ASA 7.2 (1) and later versions

    PIX (config) #crypto isakmp nat-traversal 20

  • Client VPN cannot get inside the network

    The VPN client connects to the 2600 on the serial interface, should be able to get to the 10.10.0.0 network beyond 192.168.1.14. The customer ping responds failure of external serial interface address.

    If you still have problems... can you check that there is a static route BOF 192.168.100.0/24 on router 192.168.1.14 and initiate a tracert to a host on the network of 10.10.x.x at 192.168.100.7 and see where it goes... your tests show that the VPN client knows how to get to this subnet, but it seems that there is a problem of routing between 10.X.X.X going 192.168.100.0

    I hope that helps!

  • Cisco ASA 5515 - Anyconnect users can connect to ASA, but cannot ping inside the local IP address

    Hello!

    I have a 5515 ASA with the configuration below. I have configure the ASA as remote access with anyconnect VPN server, now my problem is that I can connect but I can not ping.

    ASA Version 9.1 (1)

    !

    ASA host name

    domain xxx.xx

    names of

    local pool VPN_CLIENT_POOL 192.168.12.1 - 192.168.12.254 255.255.255.0 IP mask

    !

    interface GigabitEthernet0/0

    nameif inside

    security-level 100

    192.168.11.1 IP address 255.255.255.0

    !

    interface GigabitEthernet0/1

    Description Interface_to_VPN

    nameif outside

    security-level 0

    IP 111.222.333.444 255.255.255.240

    !

    interface GigabitEthernet0/2

    Shutdown

    No nameif

    no level of security

    no ip address

    !

    interface GigabitEthernet0/3

    Shutdown

    No nameif

    no level of security

    no ip address

    !

    interface GigabitEthernet0/4

    Shutdown

    No nameif

    no level of security

    no ip address

    !

    interface GigabitEthernet0/5

    Shutdown

    No nameif

    no level of security

    no ip address

    !

    interface Management0/0

    management only

    nameif management

    security-level 100

    192.168.5.1 IP address 255.255.255.0

    !

    passive FTP mode

    DNS server-group DefaultDNS

    www.ww domain name

    permit same-security-traffic intra-interface

    the object of the LAN network

    subnet 192.168.11.0 255.255.255.0

    LAN description

    network of the SSLVPN_POOL object

    255.255.255.0 subnet 192.168.12.0

    VPN_CLIENT_ACL list standard access allowed 192.168.11.0 255.255.255.0

    pager lines 24

    Enable logging

    asdm of logging of information

    Within 1500 MTU

    Outside 1500 MTU

    management of MTU 1500

    no failover

    ICMP unreachable rate-limit 1 burst-size 1

    ASDM image disk0: / asdm - 711.bin

    don't allow no asdm history

    ARP timeout 14400

    no permit-nonconnected arp

    NAT (exterior, Interior) static source SSLVPN_POOL SSLVPN_POOL static destination LAN LAN

    Route outside 0.0.0.0 0.0.0.0 111.222.333.443 1

    Timeout xlate 03:00

    Pat-xlate timeout 0:00:30

    Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02

    Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00

    Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00

    Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute

    timeout tcp-proxy-reassembly 0:01:00

    Floating conn timeout 0:00:00

    dynamic-access-policy-registration DfltAccessPolicy

    WebVPN

    list of URLS no

    identity of the user by default-domain LOCAL

    the ssh LOCAL console AAA authentication

    AAA authentication http LOCAL console

    LOCAL AAA authorization exec

    Enable http server

    http 192.168.5.0 255.255.255.0 management

    No snmp server location

    No snmp Server contact

    Server enable SNMP traps snmp authentication linkup, linkdown warmstart of cold start

    Crypto ipsec pmtu aging infinite - the security association

    Crypto ca trustpoint ASDM_TrustPoint5

    Terminal registration

    E-mail [email protected] / * /

    name of the object CN = ASA

    address-IP 111.222.333.444

    Configure CRL

    Crypto ca trustpoint ASDM_TrustPoint6

    Terminal registration

    domain name full vpn.domain.com

    E-mail [email protected] / * /

    name of the object CN = vpn.domain.com

    address-IP 111.222.333.444

    pair of keys sslvpn

    Configure CRL

    trustpool crypto ca policy

    string encryption ca ASDM_TrustPoint6 certificates

    Telnet timeout 5

    SSH 192.168.11.0 255.255.255.0 inside

    SSH timeout 30

    Console timeout 0

    No ipv6-vpn-addr-assign aaa

    no local ipv6-vpn-addr-assign

    192.168.5.2 management - dhcpd addresses 192.168.5.254

    !

    a basic threat threat detection

    Statistics-list of access threat detection

    no statistical threat detection tcp-interception

    SSL-trust outside ASDM_TrustPoint6 point

    WebVPN

    allow outside

    CSD image disk0:/csd_3.5.2008-k9.pkg

    AnyConnect image disk0:/anyconnect-win-3.1.04066-k9.pkg 1

    AnyConnect enable

    tunnel-group-list activate

    attributes of Group Policy DfltGrpPolicy

    Ikev1 VPN-tunnel-Protocol l2tp ipsec without ssl-client

    internal VPN_CLIENT_POLICY group policy

    VPN_CLIENT_POLICY group policy attributes

    WINS server no

    value of server DNS 192.168.11.198

    VPN - 5 concurrent connections

    VPN-session-timeout 480

    client ssl-VPN-tunnel-Protocol

    Split-tunnel-policy tunnelspecified

    value of Split-tunnel-network-list VPN_CLIENT_ACL

    myComp.local value by default-field

    the address value VPN_CLIENT_POOL pools

    WebVPN

    activate AnyConnect ssl dtls

    AnyConnect Dungeon-Installer installed

    AnyConnect ssl keepalive 20

    time to generate a new key 30 AnyConnect ssl

    AnyConnect ssl generate a new method ssl key

    AnyConnect client of dpd-interval 30

    dpd-interval gateway AnyConnect 30

    AnyConnect dtls lzs compression

    AnyConnect modules value vpngina

    value of customization DfltCustomization

    internal IT_POLICY group policy

    IT_POLICY group policy attributes

    WINS server no

    value of server DNS 192.168.11.198

    VPN - connections 3

    VPN-session-timeout 120

    Protocol-tunnel-VPN-client ssl clientless ssl

    Split-tunnel-policy tunnelspecified

    value of Split-tunnel-network-list VPN_CLIENT_ACL

    field default value societe.com

    the address value VPN_CLIENT_POOL pools

    WebVPN

    activate AnyConnect ssl dtls

    AnyConnect Dungeon-Installer installed

    AnyConnect ssl keepalive 20

    AnyConnect dtls lzs compression

    value of customization DfltCustomization

    username vpnuser password PA$ encrypted $WORD

    vpnuser username attributes

    VPN-group-policy VPN_CLIENT_POLICY

    type of remote access service

    Username vpnuser2 password PA$ encrypted $W

    username vpnuser2 attributes

    type of remote access service

    username admin password ADMINPA$ $ encrypted privilege 15

    VPN Tunnel-group type remote access

    General-attributes of VPN Tunnel-group

    address VPN_CLIENT_POOL pool

    Group Policy - by default-VPN_CLIENT_POLICY

    VPN Tunnel-group webvpn-attributes

    the aaa authentication certificate

    enable VPN_to_R group-alias

    type tunnel-group IT_PROFILE remote access

    attributes global-tunnel-group IT_PROFILE

    address VPN_CLIENT_POOL pool

    Group Policy - by default-IT_POLICY

    tunnel-group IT_PROFILE webvpn-attributes

    the aaa authentication certificate

    enable IT Group-alias

    !

    class-map inspection_default

    match default-inspection-traffic

    !

    !

    type of policy-card inspect dns preset_dns_map

    parameters

    maximum message length automatic of customer

    message-length maximum 512

    Policy-map global_policy

    class inspection_default

    inspect the preset_dns_map dns

    inspect the ftp

    inspect h323 h225

    inspect the h323 ras

    inspect the rsh

    inspect the rtsp

    inspect esmtp

    inspect sqlnet

    inspect the skinny

    inspect sunrpc

    inspect xdmcp

    inspect the sip

    inspect the netbios

    inspect the tftp

    Review the ip options

    inspect the icmp

    !

    global service-policy global_policy

    context of prompt hostname

    no remote anonymous reporting call

    : end

    Help me please! Thank you!

    Hello

    Please set ACLs to allow ICMP between these two subnets (192.168.11.0 and 192.168.12.0) and check. It should ping. Let me know if it does not work.

    Thank you

    swap

  • VPN client connected but no ping nor access to privat network

    Hello

    I have a 1802w installed, a VPN client that can connect to the router and L2L connection, which works very well.

    On the router, I see that the client is connected, but no traffic passes. In sh crypto ipsec, I see that traffic is decrypted, but no packtets are encypted.

    Can someone point me in the right direction? I have the confs and debugs attached. Thanks for the help in advance.

    Erich

    Erich,

    Looking at your configuration, two things:

    1 - is the current running configuration. I see your Tunnel L2L is configured with an address of correspondence of 101, but I don't see a 101 ACL set on the router.

    2. your Split Tunnel must be reconfigured. Which means, the source and destination must be exchanged.

    SplitList extended IP access list

    permit ip 192.168.2.0 0.0.0.255 192.168.111.0 0.0.0.255

    Split Tunneling

    http://www.Cisco.com/en/us/Tech/tk59/technologies_configuration_example09186a00800a393b.shtml#Con4

    Also, the IP address pool you assign to clients, ensure that they are not part of a LAN on your side. If so, you can then run in routing problems.

    Kind regards

    Arul

    * Please note all useful messages *.

  • PIX501 customer VPN - cannot access inside the network with VPN Session

    What follows is based on the config on the attached link:

    http://www.Cisco.com/en/us/Partner/Tech/tk583/TK372/technologies_configuration_example09186a008009442e.shtml

    PIX Ver 6.2 (3) - VPN Client 3.3.6(A) - Windows XP Client PC

    We can establish the VPN to the PIX501 session, but we cannot access the network private behind the pix.

    Here is the config - I can't determine why it does not work, we are desperate to get there as soon as POSSIBLE!

    We have the same problem with the customer 4.0.3(c)

    Thanks in advance for any help!

    =======================================

    AKCPIX00 # sh run

    : Saved

    :

    6.2 (3) version PIX

    ethernet0 nameif outside security0

    nameif ethernet1 inside the security100

    hostname AKCPIX00

    domain.com domain name

    fixup protocol ftp 21

    fixup protocol http 80

    fixup protocol h323 h225 1720

    fixup protocol h323 ras 1718-1719

    fixup protocol they 389

    fixup protocol rsh 514

    fixup protocol rtsp 554

    fixup protocol smtp 25

    fixup protocol sqlnet 1521

    fixup protocol sip 5060

    fixup protocol 2000 skinny

    fixup protocol sip udp 5060

    names of

    access-list 101 permit ip 192.168.1.0 255.255.255.0 10.0.0.0 255.255.255.0

    pager lines 24

    interface ethernet0 10baset

    interface ethernet1 10full

    Outside 1500 MTU

    Within 1500 MTU

    external IP address #. #. #. # 255.255.240.0

    IP address inside 192.168.1.5 255.255.255.0

    alarm action IP verification of information

    alarm action attack IP audit

    IP local pool akcpool 10.0.0.1 - 10.0.0.10

    history of PDM activate

    ARP timeout 14400

    Global 1 interface (outside)

    (Inside) NAT 0-list of access 101

    NAT (inside) 1 0.0.0.0 0.0.0.0 0 0

    Route outside 0.0.0.0 0.0.0.0 #. #. #. # 1

    Timeout xlate 03:00

    Timeout conn 01:00 half-closed 0: 10:00 udp 0:02:00 CPP 0: h323 from 10:00 0:05:00 sip 0:30:00 sip_media 0:02:00

    Timeout, uauth 0:05:00 absolute

    GANYMEDE + Protocol Ganymede + AAA-server

    RADIUS Protocol RADIUS AAA server

    AAA-server local LOCAL Protocol

    the ssh LOCAL console AAA authentication

    No snmp server location

    No snmp Server contact

    SNMP-Server Community public

    No trap to activate snmp Server

    enable floodguard

    Permitted connection ipsec sysopt

    No sysopt route dnat

    Crypto ipsec transform-set esp - esp-md5-hmac RIGHT

    Crypto-map dynamic dynmap 10 transform-set RIGHT

    map mymap 10-isakmp ipsec crypto dynamic dynmap

    mymap outside crypto map interface

    ISAKMP allows outside

    part of pre authentication ISAKMP policy 10

    encryption of ISAKMP policy 10

    ISAKMP policy 10 md5 hash

    10 2 ISAKMP policy group

    ISAKMP life duration strategy 10 86400

    vpngroup address akcpool pool akcgroup

    vpngroup dns 192.168.1.10 Server akcgroup

    vpngroup akcgroup by default-domain domain.com

    vpngroup split tunnel 101 akcgroup

    vpngroup idle 1800 akcgroup-time

    vpngroup password akcgroup *.

    vpngroup idle 1800 akc-time

    Telnet timeout 5

    SSH #. #. #. # 255.255.255.255 outside

    SSH timeout 15

    dhcpd address 192.168.1.100 - 192.168.1.130 inside

    dhcpd dns 192.168.1.10

    dhcpd lease 3600

    dhcpd ping_timeout 750

    dhcpd allow inside

    Terminal width 80

    Cryptochecksum:XXXXX

    : end

    AKCPIX00 #.

    Config looks good - just as domestic mine to my local network. The only thing I can think is that you may have entered commands in the wrong order - which means, you could have isakmp or encryption before the config map was complete. Write memory, then reloading the pix is a way to reset everything. If you do not want downtime:

    mymap outside crypto map interface

    ISAKMP allows outside

    Enter these two commands should be enough to reset the ipsec and isakmp.

  • Connected to the ASA via the "VPN Client" software, but cannot ping devices.

    I have a network that looks like this:

    I successfully connected inside the ASA via a software "Client VPN" tunnel network and got an IP address of 10.45.99.100/16.

    I am trying to ping the 10.45.99.100 outside 10.45.7.2, but the ping fails (request timed out).

    On the SAA, including the "logging console notifications" value, I notice the following message is displayed:

    "% 305013-5-ASA: rules asymmetrical NAT matched for flows forward and backward; "Connection for icmp src, dst outside: 10.45.99.100 inside: 10.45.7.2 (type 8, code 0) rejected due to the failure of reverse path of NAT.

    I have a vague feeling that I'm missing a NAT rule of course, but not all. What did I miss?

    Here is my configuration of ASA: http://pastebin.com/raw.php?i=ad6p1Zac

    Hello

    You seem to have a configured ACL NAT0 but is not actually in use with a command "nat"

    You would probably need

    NAT (inside) 0-list of access inside_nat0_outside

    He must manage the NAT0

    Personally, I would avoid using large subnets/networks. You probably won't ever have host behind ASA who would fill / 16 subnet mask.

    I would also keep the pool VPN as a separate network from LANs behind ASA. The LAN 10.45.0.0/16 and 10.45.99.100 - 200 are on the same network.

    -Jouni

  • Remote access to the network when AAA server is out of service help

    Hi all, I have a Cisco ASA 5510. I configured Cisco Anyconnect to authenticate via IAS from Windows. We recently had a server crash and I tried to control it remotely and via anyconnect and couldn't. Once the IAS server came, I could come back in the network.

    Y at - there a command that I'm missing that will allow me to connect to the network, even if my AAA server fell Anyconnect?

    Here is my part of the config AAA command...

    RADIUS protocol AAA-server WindowsIAS

    Max - a attempts failed 5

    AAA-server host 192.168.2.15 WindowsIAS (inside)

    XXXXXXXXXX key

    RADIUS-common-pw xxxxxxxxxx

    Thanks in advance... Dan

    Dan,

    Try to add the LOCAL keyword to your authentication server group statement in your group of tunnel or group policy.

    http://www.Cisco.com/en/us/docs/security/ASA/asa90/command/reference/A3...

    Thank you

    Sent by Cisco Support technique iPad App

  • Cisco VPN Client connected, but no secure way.

    Hello

    I can connect to a VPN server smoothly, but once connected, I'm not able to reach all local resources. When I looked at the stats of customer VPN, it shows only a single route in 'Details of the route--> secure routes', 1.1.1.1 255.255.255.255. This is the reason why I can't access any resource. This could be the cause of this problem? How can I secure roads announcing cisco customer? I don't have access to the server, but I will ask the person who can make changes.

    Thank you.

    Kind regards

    Shivani

    Shivani,

    Split tunneling is what you're looking for, it will affect your secure routes.

    Marcin

  • Allow remote access to the VPN Cisco ASDM

    Hello

    I am trying to access asdm Setup for the user remote vpn. Our ASA running version 9.1 (1). ASDM is running version 7.1 (1) 52

    I have apart from the interface within the interface enabled for vpn tunnel and I use 3rd interface (asdm_inf) dedicated to this purpose.

    In the asdm, I enabled the management to asdm_inf interface. In the section ASDM, HTTPS, Telnet, SSH, I also add ASDM/HTTPS(port 444) for asdm_inf, ip_address 0.0.0.0 mask 0.0.0.0.

    However, when I connect to the vpn client and try https://asdm_inf:444, the connection is broken with timeout.

    Where could I go wrong? Any help would be appreciated.

    Thank you

    Hello

    Well, split tunnel is incorrect, you are tunneling to 172.16.66.0/24, while your BFD which you want to manage the ASDM to is 192.168.244.0/24, so the ACL split tunnel should also 192.168.244.0/24 network.

  • ASA 5505 IPSEC VPN connected but cannot access the local network

    ASA: 8.2.5

    ASDM: 6.4.5

    LAN: 10.1.0.0/22

    Pool VPN: 172.16.10.0/24

    Hi, we purcahsed a new ASA 5505 and try to configure IPSEC VPN via ASDM; I simply run the wizards, installation vpnpool, split tunnelling, etc.

    I can connect to the ASA using the cisco VPN client and internet works fine on the local PC, but it can not access the local network (can not impossible. ping remote desktop). I tried the same thing on our Production ASA(those have both Remote VPN and Site-to-site VPN working), the new profile, I created worked very well.

    Here is my setup, wrong set up anything?

    ASA Version 8.2 (5)

    !

    hostname asatest

    domain XXX.com

    activate 8Fw1QFqthX2n4uD3 encrypted password

    g9NiG6oUPjkYrHNt encrypted passwd

    names of

    !

    interface Ethernet0/0

    switchport access vlan 2

    !

    interface Ethernet0/1

    !

    interface Ethernet0/2

    !

    interface Ethernet0/3

    !

    interface Ethernet0/4

    !

    interface Ethernet0/5

    !

    interface Ethernet0/6

    !

    interface Ethernet0/7

    !

    interface Vlan1

    nameif inside

    security-level 100

    IP 10.1.1.253 255.255.252.0

    !

    interface Vlan2

    nameif outside

    security-level 0

    address IP XXX.XXX.XXX.XXX 255.255.255.240

    !

    passive FTP mode

    clock timezone PST - 8

    clock summer-time recurring PDT

    DNS server-group DefaultDNS

    domain vff.com

    vpntest_splitTunnelAcl list standard access allowed 10.1.0.0 255.255.252.0

    access extensive list ip 10.1.0.0 inside_nat0_outbound allow 255.255.252.0 172.16.10.0 255.255.255.0

    pager lines 24

    Enable logging

    timestamp of the record

    logging trap warnings

    asdm of logging of information

    logging - the id of the device hostname

    host of logging inside the 10.1.1.230

    Within 1500 MTU

    Outside 1500 MTU

    IP local pool 172.16.10.1 - 172.16.10.254 mask 255.255.255.0 vpnpool

    no failover

    ICMP unreachable rate-limit 1 burst-size 1

    don't allow no asdm history

    ARP timeout 14400

    Global 1 interface (outside)

    NAT (inside) 0-list of access inside_nat0_outbound

    NAT (inside) 1 0.0.0.0 0.0.0.0

    Route outside 0.0.0.0 0.0.0.0 XXX.XXX.XXX.XXX 1

    Timeout xlate 03:00

    Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02

    Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00

    Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00

    Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute

    timeout tcp-proxy-reassembly 0:01:00

    Floating conn timeout 0:00:00

    dynamic-access-policy-registration DfltAccessPolicy

    AAA-server protocol nt AD

    AAA-server host 10.1.1.108 AD (inside)

    NT-auth-domain controller 10.1.1.108

    Enable http server

    http 10.1.0.0 255.255.252.0 inside

    No snmp server location

    No snmp Server contact

    Server enable SNMP traps snmp authentication linkup, linkdown cold start

    Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac

    Crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac

    Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac

    Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac

    Crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac

    Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac

    Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac

    Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac

    Crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac

    Crypto ipsec transform-set ESP-AES-128-MD5-esp - aes esp-md5-hmac

    life crypto ipsec security association seconds 28800

    Crypto ipsec kilobytes of life - safety 4608000 association

    crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 pfs Group1 set

    Crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 value transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5

    outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP

    outside_map interface card crypto outside

    crypto ISAKMP allow outside

    crypto ISAKMP policy 10

    preshared authentication

    3des encryption

    sha hash

    Group 2

    life 86400

    Telnet timeout 5

    SSH 10.1.0.0 255.255.252.0 inside

    SSH timeout 20

    Console timeout 0

    dhcpd outside auto_config

    !

    a basic threat threat detection

    Statistics-list of access threat detection

    no statistical threat detection tcp-interception

    WebVPN

    internal group vpntest strategy

    Group vpntest policy attributes

    value of 10.1.1.108 WINS server

    Server DNS 10.1.1.108 value

    Protocol-tunnel-VPN IPSec l2tp ipsec

    disable the password-storage

    disable the IP-comp

    Re-xauth disable

    disable the PFS

    IPSec-udp disable

    IPSec-udp-port 10000

    Split-tunnel-policy tunnelspecified

    value of Split-tunnel-network-list vpntest_splitTunnelAcl

    value by default-domain XXX.com

    disable the split-tunnel-all dns

    Dungeon-client-config backup servers

    the address value vpnpool pools

    admin WeiepwREwT66BhE9 encrypted privilege 15 password username

    username user5 encrypted password privilege 5 yIWniWfceAUz1sUb

    the encrypted password privilege 3 umNHhJnO7McrLxNQ util_3 username

    tunnel-group vpntest type remote access

    tunnel-group vpntest General attributes

    address vpnpool pool

    authentication-server-group AD

    authentication-server-group (inside) AD

    Group Policy - by default-vpntest

    band-Kingdom

    vpntest group tunnel ipsec-attributes

    pre-shared-key BEKey123456

    NOCHECK Peer-id-validate

    !

    !

    privilege level 3 mode exec cmd command perfmon

    privilege level 3 mode exec cmd ping command

    mode privileged exec command cmd level 3

    logging of the privilege level 3 mode exec cmd commands

    privilege level 3 exec command failover mode cmd

    privilege level 3 mode exec command packet cmd - draw

    privilege show import at the level 5 exec mode command

    privilege level 5 see fashion exec running-config command

    order of privilege show level 3 exec mode reload

    privilege level 3 exec mode control fashion show

    privilege see the level 3 exec firewall command mode

    privilege see the level 3 exec mode command ASP.

    processor mode privileged exec command to see the level 3

    privilege command shell see the level 3 exec mode

    privilege show level 3 exec command clock mode

    privilege exec mode level 3 dns-hosts command show

    privilege see the level 3 exec command access-list mode

    logging of orders privilege see the level 3 exec mode

    privilege, level 3 see the exec command mode vlan

    privilege show level 3 exec command ip mode

    privilege, level 3 see fashion exec command ipv6

    privilege, level 3 see the exec command failover mode

    privilege, level 3 see fashion exec command asdm

    exec mode privilege see the level 3 command arp

    command routing privilege see the level 3 exec mode

    privilege, level 3 see fashion exec command ospf

    privilege, level 3 see the exec command in aaa-server mode

    AAA mode privileged exec command to see the level 3

    privilege, level 3 see fashion exec command eigrp

    privilege see the level 3 exec mode command crypto

    privilege, level 3 see fashion exec command vpn-sessiondb

    privilege level 3 exec mode command ssh show

    privilege, level 3 see fashion exec command dhcpd

    privilege, level 3 see the vpnclient command exec mode

    privilege, level 3 see fashion exec command vpn

    privilege level see the 3 blocks from exec mode command

    privilege, level 3 see fashion exec command wccp

    privilege see the level 3 exec command mode dynamic filters

    privilege, level 3 see the exec command in webvpn mode

    privilege control module see the level 3 exec mode

    privilege, level 3 see fashion exec command uauth

    privilege see the level 3 exec command compression mode

    level 3 for the show privilege mode configure the command interface

    level 3 for the show privilege mode set clock command

    level 3 for the show privilege mode configure the access-list command

    level 3 for the show privilege mode set up the registration of the order

    level 3 for the show privilege mode configure ip command

    level 3 for the show privilege mode configure command failover

    level 5 mode see the privilege set up command asdm

    level 3 for the show privilege mode configure arp command

    level 3 for the show privilege mode configure the command routing

    level 3 for the show privilege mode configure aaa-order server

    level mode 3 privilege see the command configure aaa

    level 3 for the show privilege mode configure command crypto

    level 3 for the show privilege mode configure ssh command

    level 3 for the show privilege mode configure command dhcpd

    level 5 mode see the privilege set privilege to command

    privilege level clear 3 mode exec command dns host

    logging of the privilege clear level 3 exec mode commands

    clear level 3 arp command mode privileged exec

    AAA-server of privilege clear level 3 exec mode command

    privilege clear level 3 exec mode command crypto

    privilege clear level 3 exec command mode dynamic filters

    level 3 for the privilege cmd mode configure command failover

    clear level 3 privilege mode set the logging of command

    privilege mode clear level 3 Configure arp command

    clear level 3 privilege mode configure command crypto

    clear level 3 privilege mode configure aaa-order server

    context of prompt hostname

    no remote anonymous reporting call

    Cryptochecksum:447bbbc60fc01e9f83b32b1e0304c6b4

    : end

    Captures we can see packets going from the pool to the internal LAN, but we do not reply back packages.

    The routing must be such that for 172.16.10.0/24 packages should reach the inside interface of the ASA.

    On client machines or your internal LAN switch, you need to add route for 172.16.10.0/24 pointing to the inside interface of the ASA.

  • ASA 5512 Anyconnect VPN cannot connect inside the network 9.1 x

    Hello

    I'm new to ASA, can I please help with this. I managed to connect to the vpn through the mobility cisco anyconnect client, but I am unable to connect to the Internet. the allocated ip address was 172.16.1.60 and it seems OK, I thought my acl and nat is configured to allow and translate the given vpn ip pool but I'm not able to ping anything on the inside.

    If anyone can share some light... There's got to be something escapes me...

    Here's my sh run

    Thank you

    Raul

    -------------------------------------------------------------------------------

    DLSYD - ASA # sh run

    : Saved
    :
    ASA 9.1 Version 2
    !
    hostname DLSYD - ASA
    domain delo.local
    activate the encrypted password of UszxwHyGcg.e6o4z
    names of
    mask 172.16.1.60 - 172.16.1.70 255.255.255.0 IP local pool DLVPN_Pool
    !
    interface GigabitEthernet0/0
    Shutdown
    No nameif
    no level of security
    no ip address
    !
    interface GigabitEthernet0/1
    Shutdown
    No nameif
    no level of security
    no ip address
    !
    interface GigabitEthernet0/2
    Post description
    10 speed
    full duplex
    nameif Ext
    security-level 0
    IP 125.255.160.54 255.255.255.252
    !
    interface GigabitEthernet0/3
    Description Int
    10 speed
    full duplex
    nameif Int
    security-level 100
    IP 192.168.255.2 255.255.255.252
    !
    interface GigabitEthernet0/4
    Shutdown
    No nameif
    no level of security
    no ip address
    !
    interface GigabitEthernet0/5
    Shutdown
    No nameif
    no level of security
    no ip address
    !
    interface Management0/0
    management only
    nameif management
    security-level 100
    IP 192.168.1.1 255.255.255.0
    !
    boot system Disk0: / asa912-smp - k8.bin
    passive FTP mode
    clock timezone IS 10
    clock daylight saving time EDT recurring last Sun Oct 02:00 last Sun Mar 03:00
    DNS lookup field inside
    DNS domain-lookup Int
    DNS server-group DefaultDNS
    192.168.1.90 server name
    192.168.1.202 server name
    domain delo.local
    permit same-security-traffic intra-interface
    network dlau40 object
    Home 192.168.1.209
    network dlausyd02 object
    host 192.168.1.202
    network of the object 192.168.1.42
    host 192.168.1.42
    dlau-utm network object
    host 192.168.1.50
    network dlauxa6 object
    Home 192.168.1.62
    network of the 192.168.1.93 object
    host 192.168.1.93
    network dlau-ftp01 object
    Home 192.168.1.112
    dlau-dlau-ftp01 network object
    network dlvpn_network object
    subnet 172.16.1.0 255.255.255.0
    the object-group Good-ICMP ICMP-type
    echo ICMP-object
    response to echo ICMP-object
    ICMP-object has exceeded the time
    Object-ICMP traceroute
    ICMP-unreachable object
    DLVPN_STAcl list standard access allowed 192.168.0.0 255.255.0.0
    Standard access list DLVPN_STAcl allow 196.1.1.0 255.255.255.0
    DLVPN_STAcl list standard access allowed 126.0.0.0 255.255.0.0
    Ext_access_in access list extended icmp permitted any object-group Good-ICMP
    Ext_access_in list extended access permitted tcp dlau-ftp01 eq ftp objects
    Ext_access_in list extended access permit tcp any object dlausyd02 eq https
    Ext_access_in list extended access permit tcp any object dlau-utm eq smtp
    Ext_access_in list extended access permit tcp any object dlauxa6 eq 444
    Ext_access_in access-list extended permitted ip object annete-home everything
    pager lines 24
    Enable logging
    asdm of logging of information
    MTU 1500 Ext
    MTU 1500 Int
    management of MTU 1500
    ICMP unreachable rate-limit 1 burst-size 1
    ASDM image disk0: / asdm - 713.bin
    don't allow no asdm history
    ARP timeout 14400
    no permit-nonconnected arp
    NAT (Int, Ext) static source any any destination static dlvpn_network dlvpn_network non-proxy-arp
    !
    network dlausyd02 object
    NAT (Int, Ext) interface static tcp https https service
    dlau-utm network object
    NAT (Int, Ext) interface static tcp smtp smtp service
    network dlauxa6 object
    NAT (Int, Ext) interface static tcp 444 444 service
    network dlau-ftp01 object
    NAT (Int, Ext) interface static tcp ftp ftp service
    Access-group Ext_access_in in Ext interface
    Route Ext 0.0.0.0 0.0.0.0 125.255.160.53 1
    Route Int 192.168.0.0 255.255.0.0 192.168.255.1 1
    Timeout xlate 03:00
    Pat-xlate timeout 0:00:30
    Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
    Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
    Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
    Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
    timeout tcp-proxy-reassembly 0:01:00
    Floating conn timeout 0:00:00
    dynamic-access-policy-registration DfltAccessPolicy
    identity of the user by default-domain LOCAL
    AAA authentication enable LOCAL console
    AAA authentication LOCAL telnet console
    AAA authentication http LOCAL console
    LOCAL AAA authentication serial console
    the ssh LOCAL console AAA authentication
    http server enable 44310
    http server idle-timeout 30
    http 192.168.0.0 255.255.0.0 Int
    No snmp server location
    No snmp Server contact
    Server enable SNMP traps snmp authentication linkup, linkdown warmstart of cold start
    Crypto ipsec pmtu aging infinite - the security association
    trustpool crypto ca policy
    Telnet 192.168.1.0 255.255.255.0 management
    Telnet timeout 30
    SSH 192.168.0.0 255.255.0.0 Int
    SSH timeout 30
    SSH group dh-Group1-sha1 key exchange
    Console timeout 0
    No ipv6-vpn-addr-assign aaa
    no local ipv6-vpn-addr-assign
    management of 192.168.1.2 - dhcpd address 192.168.1.254
    enable dhcpd management
    !
    a basic threat threat detection
    Statistics-list of access threat detection
    no statistical threat detection tcp-interception
    NTP server 61.8.0.89 prefer external source
    SSL encryption rc4-aes128-sha1 aes256-3des-sha1 sha1 sha1
    WebVPN
    port 44320
    allow outside
    Select Ext
    AnyConnect essentials
    AnyConnect image disk0:/anyconnect-win-3.1.05170-k9.pkg 1
    AnyConnect enable
    tunnel-group-list activate
    internal GroupPolicy_DLVPN group strategy
    attributes of Group Policy GroupPolicy_DLVPN
    WINS server no
    value of server DNS 192.168.1.90 192.168.1.202
    client ssl-VPN-tunnel-Protocol
    Split-tunnel-policy tunnelspecified
    value of Split-tunnel-network-list DLVPN_STAcl
    delonghi.local value by default-field
    WebVPN
    AnyConnect Dungeon-Installer installed
    time to generate a new key 30 AnyConnect ssl
    AnyConnect ssl generate a new method ssl key
    AnyConnect ask flawless anyconnect
    encrypted vendor_ipfx pb6/6ZHhaPgDKSHn password username
    vendor_pacnet mIHuYi1jcf9OqVN9 encrypted password username
    username admin password encrypted tFU2y7Uo15ahFyt4
    type tunnel-group DLVPN remote access
    attributes global-tunnel-group DLVPN
    address pool DLVPN_Pool
    Group Policy - by default-GroupPolicy_DLVPN
    tunnel-group DLVPN webvpn-attributes
    enable DLVPN group-alias
    !
    class-map inspection_default
    match default-inspection-traffic
    !
    !
    type of policy-card inspect dns preset_dns_map
    parameters
    maximum message length automatic of customer
    message-length maximum 512
    Policy-map global_policy
    class inspection_default
    inspect the preset_dns_map dns
    inspect h323 h225
    inspect the h323 ras
    inspect the rsh
    inspect the rtsp
    inspect esmtp
    inspect sqlnet
    inspect the skinny
    inspect sunrpc
    inspect xdmcp
    inspect the netbios
    Review the ip options
    inspect the ftp
    inspect the tftp
    !
    global service-policy global_policy
    SMTPS
    Server 192.168.1.50
    Group Policy - by default-DfltGrpPolicy
    context of prompt hostname
    no remote anonymous reporting call
    Cryptochecksum:67aa840d5cfff989bc045172b2d06212
    : end
    DLSYD - ASA #.

    Hello

    Add just to be sure, the following configurations related to ICMP traffic

    Policy-map global_policy
    class inspection_default
    inspect the icmp
    inspect the icmp error

    Your NAT0 configurations for traffic between LAN and VPN users seem to. Your Split Tunnel ACL seems fine too because it has included 192.168.0.0/16. I don't know what are the other.

    I wonder if this is a test installation since you don't seem to have a dynamic PAT configured for your local network at all. Just a few static PAT and the NAT0 for VPN configurations. If it is a test configuration yet then confirmed that the device behind the ASA in the internal network has a default route pointing to the ASAs interface and if so is it properly configured?

    Can you same ICMP the directly behind the ASA which is the gateway to LANs?

    If you want to try ICMP interface internal to the VPN ASA then you can add this command and then try ICMP to the internal interface of the ASA

    Int Management-access

    As the post is a little confusing in the sense that the subject talk on the traffic doesn't work not internal to the network, while the message mentions the traffic to the Internet? I guess you meant only traffic to the local network because you use Split Tunnel VPN, which means that Internet traffic should use the VPN local Internet users while traffic to the networks specified in the ACL Tunnel Split list should be sent to the VPN.

    -Jouni

Maybe you are looking for

  • Drivers Vista 32-bit works on XP 32 bit?

    I got this HP model a6544f since a few months now and find that much too much my older hardware (scanner, etc.) and 16-bit software (which I use daily) simply does not work with Vista or a 64-bit OS. I prefer to use XP 32-bit where all happy lives on

  • Connections of encoder with cDAQ 9401

    I hope that some of the experts here can help me with this as I am new to encoders. I want to make sure I connect this right but am finding conflicting information on this subject. I found this tutorialwhich shed some light on some things for me.  If

  • Hard drive stuck in the RAW file system.

    So I had a problem with my slave drive being stuck in the RAW file system when I formatted my master drive. So I disconnected the slave drive and formatted the master once again and once all updates have been installed, I plugged the slave back in. H

  • QuickPlay: the name of the deleted video still appears in the list of all the videos of Quickplay

    I deleted a video, but the name is still present in quickplay. How can I locate this link and delete?

  • I forgot the password of the admin user for Windows 7

    I changed my password a while but my children damaged my computer and so it's been a few months that I could use it so now I forgot it. I read that I have to use a Windows repair CD, but I have not one of these? My concern is that I have a lot of my