Cisco ISE & 250 series Cisco switches

Similar Questions

• The ISE Cisco switch configuration

  Hi experts,

  I got the following network:

  Devices-> switch access-->--> access switch central office switch-> ISE Server

  All switches are capable IOS for the 802. 1 X and configurations of AAA for ISE to manage network devices. However, I read in the guide on the configuration of the switches in preparation for the deployment of the ISE of CIsco, but I wonder what should I configure switches for access and basic switches or only configure the switches for access to EHT?

  Thanks for your time to read!

  If all clients are non-DHCP clients, then no configuration is based or distribution at all.

  But you may need to search different options of profiling, if the customers are not active DHCP. Access switch supports the function of detection IOS? Would be very useful to have such a that it would send important profiling information at ISE. You may need to use the right options for ISE of profiling to determine the details of the endpoint.

  Concerning

  Vivek

• 10G Cisco switch

  I would like to know if the compatibility for the storage matrix Dell is updated regularly, especially for cisco switches.
  We seek to deploy a few PS6210 with 10G connectiivity and here for use with switches Cisco 4500 X series. However these are not included in the doc. There are a few cisco switches that are the end of life (4948 and some nexus switches).

  Hello

  Yes the guide is updated regularly, usually monthly or updates are available.

  Since the x 4500 is not a Nexus series switch, you looking for correct DCB support?

  In this case these Dell 'Level 3' offers better support for resonable effort.   I'll make sure that use you the latest firmware IOS and EQL.  There are other switches catalyst IOS in the guide.  Configure it in this sense would be a great place to start.   Ideally, the switch dedicated for iSCSI use, not VLANd with other types of traffic.

  If you can first test before production, then support can see table diagnosis and SANHQ archive for any signs of network related issues.   (retransmit rate and types for example)

  Kind regards

• C300 Cisco switches when Cisco is considering additional CDP?

  Dear all,

  When Cisco plans to support CDP on C300 switches?

  I have it configured with LLDP based on the document "Adding a Cisco Switch series of 300 Business from small to SBCS 2.0", but this isn't the perfect according to me

  Kind regards

  Vellum Tsekov

  Vellum,

  We are very close. We anticipate releasing the firmware supporting CDP, CLI and several other new features this month - June 2011.

  Ivor

• MacBook as Cisco Switch profiles in 2.1

  I'm experimenting with trying to Mac to the profile to the ISE. 2.1. I tried installing AnyConnect, and for some reason he sees it as a Nexus 7000 switch.

  Here's the debug info

  Attribute: AAA-server value: ise-2
  Attribute: Airespace-Wlan-Id value: 5
  Attribute: AllowedProtocolMatchedRule value: EAP_Chaining_Wireless
  Attribute: AuthenticationMethod value: MSCHAPV2
  Attribute: AuthorizationPolicyMatchedRule value: default
  Attribute: BYODRegistration value: unknown
  Attribute: CacheUpdateTime value: 1465417705907
  Attribute: Called-Station-ID value:20-3a-07-66-96-20
  Attribute: Calling-Station-ID value:a4-5e-60-cf-81-83
  Attribute: CreateTime value: 1464896196500
  Attribute: DestinationIPAddress value: 10.10.207.156
  Attribute: Value DestinationPort: 1812
  Attribute value: DetailedInfo: authentication succeed
  Attribute value: IP address: 10.10.204.114
  Value of the attribute identifier: Device:
  Attribute value: device Port: 32772
  Attribute: Value Type Device: Device Type #All Types of devices
  Attribute: DeviceCompliance value: unknown
  Attribute: DeviceRegistrationStatus value: NotRegistered
  Attribute: value:A4-5E-60-CF-81-83 EndPointMACAddress
  Attribute: EndPointPolicy value: Cisco-switch
  Attribute value: EndPointPolicyID: 4afc4ae0-6d8e-11e5-978e-005056bf2f0a
  Attribute: EndPointProfilerServer value: ise-2
  Attribute: EndPointSource value: RADIUS probe
  Attribute: FailureReason value: 5440 abandoned Endpoint EAP session and began again
  Attribute: FirstCollection value: 1464896196418
  Attribute: value Framed-IP-Address:
  Attribute: value Framed-IPv6-Address:
  Attribute: IdentityAccessRestricted value: false
  Attribute value: IdentityGroup: profile
  Attribute value: IdentityGroupID: b132c920-6d8d-11e5-978e-005056bf2f0a
  Attribute: IsThirdPartyDeviceFlow value: false
  Attribute: LastActivity value: 1465417705904
  Attribute: LastNmapScanTime value: 1465245395228
  Attribute: value: a place #All locations
  Attribute: LogicalProfile value: infrastructure network devices
  Attribute: MACAddress value: A4:5E:60:CF:81:83
  Attribute value: MDMServerID:
  Attribute: MatchedPolicy value: Cisco-switch
  Attribute value: MatchedPolicyID: 4afc4ae0-6d8e-11e5-978e-005056bf2f0a
  Attribute: Value MessageCode: 5440
  Attribute: NAS-IP-address value: 10.10.204.114
  Attribute: NAS-identifier value: WLC-3
  Attribute: NAS-Port value: 1
  Attribute: NAS-Port-Type value: Wireless - IEEE 802.11
  Attribute value: Network Device Profile: Cisco
  Attribute: NetworkDeviceGroups value: location #All locations, Types of devices Device Type #All
  Attribute: NetworkDeviceName value: WLC-3
  Attribute value: NetworkDeviceProfileId: 8ade1f15-aef1-4a9a-8158-d02e835179db
  Attribute: NetworkDeviceProfileName value: Cisco
  Attribute: NmapScanCount value: 1
  Attribute: NmapSubnetScanID value: 0
  Attribute: YES value: Apple, Inc.
  Attribute value: PhoneID:
  Attribute: PolicyVersion value: 32
  Attribute value: PortalUser:
  Attribute: PostureApplicable value: Yes
  Attribute: PostureAssessmentStatus value: NotApplicable
  Attribute value: PostureExpiry:
  Attribute: PostureStatus value: unknown
  Attribute: RadiusFlowType value: Wireless802_1x
  Attribute: RadiusPacketType value: AccessRequest
  Attribute: RegistrationTimeStamp value: 0
  Attribute value: response: {RadiusPacketType = drop ;}
  Attribute: SSID value:20-3a-07-66-96-20
  Attribute: SelectedAccessService value: lack of access to the network
  Attribute value: SelectedAuthenticationIdentityStores: the internal users, ise-2, All_AD_Join_Points
  Attribute: SelectedAuthorizationProfiles value: DenyAccess
  Attribute: Service-Type value: box
  Attribute: StaticAssignment value: false
  Attribute: StaticGroupAssignment value: false
  Attribute: StepData value: 4 = standardized Radius.RadiusFlowType, 5 = EAP_Chaining_Wireless
  Attribute value: TLSCipher: ECDHE-RSA-AES256-SHA
  Attribute: TLSVersion value: TLSv1
  Attribute: TimeToProfile value: 44
  Factor of certainty attribute value: Total: 30
  Attribute value: UniqueSubjectID:
  Attribute: UpdateTime value: 1465245396597
  Attribute: allowEasyWiredSession value: false
  Attribute: Host-name value:
  Value of the attribute: ip:
  Attribute: value operating system switch: Cisco Nexus 7000 (NX - OS 4.2.6) (99% accuracy)
  Attribute: result of operating-system value: Cisco Nexus 7000 switch (NX - OS 4.2.6) (99% accuracy)
  Attribute: SkipProfiling value: false

  Yes you must add the ISE server in your help-dhcp (dhcp relay) in order to obtain information about the DHCP request to profile correctly the devices.

  Even after setting correctly ISE in your DHCP relay, you aren't able to profile?

• Why I can't command show running on cisco switch

  On a single switch, I found that some commands because they show execution or copy running-config tftp: on cisco switch WS-C2960X-24TS-L does not work it see more below. How I can use the command then show generally. Thank you.

  Building1_FAA_6F_SW3 #sh run
  Building configuration...

  Current configuration: 100 bytes
  !
  ! No change since the last restart configuration
  !
  boot-start-marker
  boot-end-marker
  !
  !
  !
  !
  !
  !
  end

  ---------------------------------------------------

  Building1_FAA_6F_SW3 #copy running-config tftp:
  ^
  Invalid entry % detected at ' ^' marker.

  OK, so the information you provided in your latest messages confirm that the privilege level you get via telnet/vty is different from the one you get via the console. This is due to the configuration of AAA which applies to the vty ports but not on the console port.

  So if you want the same rules apply to the console port, then you must configure the port console for AAA as well.

  If you don't want these rules then you need to remove the AAA configurations. The best way to remove these is by typing 'no new aaa - model' However, careful not to lock you out of the unit. Make sure you have local accounts with the privilege level 15 and you also know the active password/secret.

  I hope this helps!

  Thank you for evaluating useful messages!

• To the main unit Infrastructure Cisco switch port

  Hello.

  I had a doubt as to the Port of the Switch in my Cisco Switch for a camera of the first Infrastructure.

  This port must be a Switchport to access or a Switchport Trunk?

  What is your recommendation on this subject? What is best practice?

  Thank you very much.

  Access port should work fine. You do not configure a VLAN on the device itself, just the IP address / subnet and default gateway.

  Thank you

  Ric

• Configuration Wireless 3G as online backup with cisco switch layer 3?

  Hi all

  We have an existing GPRS modems for data transfer between 2 different sites, this connection is a bit slow to no more than approximately 114 Kbps, the idea is to add a 3G modem, so the solution will be based on a two-way communication lines which are 3G network and the GPRS network.

  The line GPRS will be the main and 3G will be secondary, this redundancy offers a high level of availability of communication between the two sites.

  is it possible to configure this redundancy with a cisco switch layer 3? If this is the case do you have a tutorial or a link which explain how to do this work with a layer switch 3 ciso?

  all information will be useful for me, thanks

  Hello

  The config is one provided by anisaini, but you need to change your NAT like this:

  IP nat inside source MAIN interface map route x/x main interface

  IP nat inside source route-map interface o/o interface secondary SCHOOL

  Interior int z/z interface

  IP nat inside

  int x/x

  NAT outside IP

  int y/y

  NAT outside IP

  access-list 99

  permit x.x.x.x y.y.y.y where x.x.x.x is your home subnet addresses and y.y.y.y is the corresponding generic mask

  PRIMARY route map

  match ip add 99

  match interface x/x

  SECONDARY route map

  match ip add 99

  game interface y/y

  Concerning

  Alain

  Remember messages useful rate.

• Circuits on Cisco Switch SG200-50

  Hi all

  I'm trying to inter vlan routing using Cisco Switch SG200-50 with router Cisco 1941. The router I created three subinterface for VLAN1, 2, 3 and VLAN1 is vlan native. I have a LWAP with Cisco WLC connected to the same switch. I have activated assignemnet vlan dynamic using Windows /NPS. RADIUS Wireless successfully user can authenticate as well the vlan is assigned, but unable to ping the router subinterface.

  On the switch, you must activate the trunk port connected to the router ports and AP, tried all means, what makes the trunk port and General, nothing worked. users are unable to ping the gateway.

  If you have worked on this switch, pls help how to on this subject.

  If the Cisco technical support team can help me, that would be great

  Thanks in advance

  Concerning

  Joe

  Hi Joseph, creating a general port and disable the input filter and label properly login vlan. Also make sure your sub interface are dot1q.

  -Tom
  Please mark replied messages useful

• Web authentication with RSA SecureID on a Cisco Switch

  Hello

  I recently searched by linking in our Cisco Switch of GB 2960 S with RSA SecureID via Radius

  I already managed to tie in to ssh access

  but I failed to make it work for http / web access to the switch

  I think it's because we use 'single use' maximum security with RSA SecureID tokens

  the web interface tries to authenticate several times against the Radius server RSA SecureID part

  (agreement on the first authentication, but every time after that he's going to want a different code in token)

  I was wondering if anyone knew a way around this? (if there is a way to get the right switch authenticate once instead of multiple times the radius server)

  FYI, the switch is a WS-C2960S-24TS-L with IOS 15.0 (1) SE2

  Hello Chris,

  You can test the following configuration?

  AAA webtac_grp radius server group

  Server

  expiration of cache 1

  authorization cache profile httpauth

  hiding authentication profile httpauth

  !

  AAA authentication login httpauth cache webtac_grp group webtac_grp

  AAA authorization exec httpauth cache webtac_grp group webtac_grp

  AAA authorization network httpauth cache webtac_grp group webtac_grp

  AAA cache profile httpauth

  all the

  IP http server

  IP http authentication aaa - authentication of the connection httpauth

  IP http authentication aaa exec-authorization httpauth

  RADIUS server host key *.

  I know for sure the above configuration works when you use GANYMEDE + instead of RADIUS in order to avoid multiple guests due to the authentication of JAVA Applets to access the GUI of the IOS. I him have not tested against RSA acting as an authentication server.

  NOTE: As "aaa authorization exec" is configured the RSA should send Service-Type attribute with administrative value for it to work as expected.

  If this was helpful please note.

  Kind regards.

• Turn on the mtu on cisco switch and cisco user server

  Hi all

  someone got bad luck turning on the mtu on their cisco switch?  I guess I need to turn it on for all because the command is for all ports on cisco catalyst and my server switch is nearby to my user of switches and a broadband bandwidth 6 G or 6 ports, I need to turn it on for all user ports?

  Thanks for any comments, that you can add.

  I assume you mean Jumbo frame support! You shouldn't have any problems with that. Please take a look at for example http://www.cisco.com/en/US/products/hw/switches/ps700/products_configuration_example09186a008010edab.shtml for more details and the configuration of the different switches. According to the model, the parameters are for dedicated ports only or the entire switch. In the case of the switch everything you will need to reload (reboot) switch, so be careful.

  André

• How to automate the SSH connection/commands on a series of switches PowerConnect 3400 3500 and 6200 series.

  I'm trying to find a way to automate the commands to send a series of switches (about 20) showing some configs and save the output to a file. The way I was trying to do was using plink and creation of a batch of files for her.

  Essentially, it would be something similar to the following.

  ECHO for /f % in (devices.txt) plink % l word of PAST of USERNAME-pw-v - m C:\Batch\commands.txt > output.txt

  To split the above command, looking for my ips in the devices.txt and made a "plink pw - username PASSWORD - v IP-l m - COMMANDS > OUTPUT" for each. The problem, I'm running is that the switches do not accept logins, they constantly ask for the user and the password again. Even when you try to put them in the commands.txt he will not accept the entry. I googled using plink with dell switches but there is nothing to talk about this problem.

  So my question is, is it possible to automate this sort of thing in a batch file? Or some way to automate a series of commands to a switch via SSH? I'm just not wan't do manually connect to each of them, carry out my orders, out, reconnect and repeat. I did it on cisco switches so I thought the process would be similar but I don't understand what obstacle I'm running in here. Ideally, I'd like to see how to do this via SSH but at this point, I am ready to accept almost any alternative (secure) to automate the sending of orders for my switches.

  I hope that all makes sense.

  Sorry, I haven't used before plink, so I'm not sure what to change to get this to work. In the past, there was another Member of the community who has been able to use expect to establish connections to switches and save configs.

  Linux.Die.net/.../expect

  It may be somewhat more than installation, but you can be able to make it work for your needs.

  http://Dell.to/1RONL3D

  Let us know

• Plug-and-Play for Cisco Small Business 300 Series managed switch

  Nice day

  What are the automatic installation options available for the Managed Switch series of Cisco Small Business 300?

  It seems there are not, the operating system is not the standard IOS I used to.

  I would use with ability to bridge the Infrastructure first Cisco PnP.

  Concerning

  Stone

  First Infrastructure use and assume an agent CNS (Cisco Network Services) on the other side, when you enable the 'plug & play '. Series 300/500 do not run IOS and does not include the CNS agent, but there is a way to activate the automatic configuration. Switches supported by the automatic DHCP configuration (using DHCP options 66, 67, etc.) in which case they automatically download their config to a TFTP server at boot time. This allows an administrator to put the configs for all switches on a TFTP server and simply start a default switch factory in order to obtain config.

  Seal a document shows how this is done.

  Hope that the information would be useful.

• Configuration of SNMP on Cisco Small Business 300 Series managed switch

  Please can someone help me configure SNMP on Cisco Small Business 300 series switch?

  Thank you

  Hi Anton,.

  Don't forget to activate the service SNMP is first of all: Security > Services TCP/UDP.

  http://sbkb.Cisco.com/CiscoSB/UKP.aspx?VW=1&docid=3b13278d9ef9402a8fef57...

  also, you will find useful documents for configuration etc on our server community kb:

  http://sbkb.Cisco.com/CiscoSB/UKP.aspx?VW=1&docid=183cae2148d445b2a07473...

  Let us know if you have any problems.

  Aleksandra

• Configs ISE Cisco switch

  I guess Cisco ISE sends a redirect to URL to the switch and switch, it presents to the customer in the case of access comments get a redirect URL with acceptance of the user (guests and not wired) Page.

  My question is, do we need to configure the server http and https on the switches (both pleading and authenticator)?

  I don't know that it will take a confirmation, but just wanted to...

  I checked the configuration for the supplicant and authenticator of ISE switches, and there no where not mentioned this part of the config.

  http://www.Cisco.com/en/us/docs/security/ISE/1.0/user_guide/ise10_troubleshooting.html (a redirect to URL and possible cause problem is mentioned) - make sure that the config is necessary.

  http://www.Cisco.com/c/en/us/TD/docs/switches/LAN/catalyst2960x/software/15-0_2_EX/security/configuration_guide/b_sec_152ex_2960-x_cg/b_sec_152ex_2960-x_cg_chapter_010000.html

  (the begging and authenticator switch configuration) - mentioned anywhere in the configuration of http/https for the two switches.

  Yes, his need.  The http/s server in the swtich is used to retrieve the user http traffic and redirect the traffic to the CWA portal, or a registration portal device or even for the portal of integrated Mobile Device Management (MDM).  .

  IP http server

  IP http secure server

  The info below, I caught Cisco ISE for BYOD and book secure access unified.

  "Organization many want if ensure that this referral process to aid internal HTTP Server switch is dissociated from the management of the switch itself, in order to limit the risk of the user interacts with the intervace plan a switch of control and management."  This can be accomplished by connecting the two following commands in global configuration mode:

  active session modules IP http no

  "IP http secure-active-session-modules no".