CIsco ISE with HP and Fortigate

Hello

I configured the switches HP 5820 X and 5130 for authentication radius AAA with Cisco ISE 2.0.0.306.

The switch receives the response from authorization successful; but unable to connect. What are the Advanced profile Radius authorization attributes in

ISE?

In addition, ISE supports Fotigate firewall?

Oh and Yes ISE supports any device using the RADIUS in accordance with rfc, it is usually only a question about this that av-pairs to send to that specific device, there is not really standard for this.

Tags: Cisco Security

Similar Questions

  • Cisco ISE with GANYMEDE + and RADIUS both?

    Hello

    I'm wired opening of authentication on a network using Cisco ISE. I studied the conditions for this. I know that I need to enable the RADIUS on the Cisco switches on the network. The switches in the network are already programmed to GANYMEDE +. Anyone know if they can both operate on the same network at the same time?

    Bob

    I suppose that Ganymede is configured (with ACS 4.x or 5.x) for the peripheral administration via telnet/ssh, and now you need the RADIUS (radius) to authenticate 802. 1 x. Yes they can both work on the same network at the same time.

    ~ BR
    Jatin kone

    * Does the rate of useful messages *.

  • Cisco ISE 2.0 and WLC 5508 with 7.6.130.0

    I have looked on the release notes and compatibility n for ISE 2.0 and have not seen the answer to that. For the WLC 5508, the minimum AirOS is 7.0.116.0 but he limited the AAA authentication and support for comments. The recommended version of AirOS is 8.0.121.0.

    http://www.Cisco.com/c/en/us/TD/docs/security/ISE/2-0/compatibility/ISE _...

    What airos 7.6.130.0? I know that AirOS release works with 1.3 and 1.4, even if they show the same support for version 2.0. I'm just afraid that something may have changed with 2.0. I am concerned only about the AAA authentication and guest access. No BYOD, posture or MDM is necessary.

    No change. Works well.

  • Cisco ISE 1.2 and the ad group

    Hello

    I have Cisco ISE installed on my EXSi server for my test pilot. I added several ad groups at ISE as well.

    I created a condition of authorization policy, that is WIRELESS_DOT1X_USERS (see screenshot)
    Basically, I just replicate the default Wireless_802.1X and added Network Access: EapAuthentication, Equals, EAP - TLS.

    My problem is, I have been unable to join the wireless network, if I added my ad group to the authorization strategy (see screenshot). The user I is a member of WLAN USERS. If I removed the authorization policy group, the use is able to join the wireless network.

    I have attached the screenshot of ISE newspapers as well. I checked the ISE, AD/NPS, WLC, laptop computer time and date, and they are all in sync.

    I also have the WLC added as NPS client on my network.

    I checked the newspaper AD and I found it, it was the local management user WLCs trying to authenticate. It is supposed to be my wireless user Credential is not the WLC.

    It's the paper I received from the AD/NPS

    Access denied to user network policy server.

    Contact the server administrator to strategy network for more information.

    User:

    Security ID: NULL SID

    Account name: admin

    Domain account: AAENG

    Account name: AAENG\admin

    Client computer:

    Security ID: NULL SID

    Account name: -.

    Full account name: -.

    OS version: -.

    Called Station identifier: -.

    Calling the Station identifier: -.

    NAS:

    NAS IPv4 address: 172.28.255.42

    NAS IPv6 address: -.

    NAS identifier: RK3W5508-01

    NAS Port Type: -.

    NAS Port:                              -

    RADIUS client:

    Friendly name of client: RK3W5508-01

    The client IP address: 172.28.255.42

    Information about authentication:

    Connection request policy name: Windows authentication for all users use

    The network policy name: -.

    Authentication provider: Windows

    Authentication server: WIN - RSTMIMB7F45.aaeng.local

    Authentication type: PAP

    EAP Type:                              -

    Identifier for account: -.

    Results of logging: Accounting Information was written in the local log file.

    Reason code: 16

    Reason: Authentication failed due to incompatibility of user credentials. The provided username is not mapped to an existing user account or the password is incorrect.

    Hello

    The problem is with what ISE name, it's choosing to search of the AD. If you look in the ISE newspapers down, you'll see the username that use ISE (firstname, lastname) to search for the AD.

    In your certificate template see what attribute containst name AD (possibly the dns name or email or the name of principle of RFC 822 NT), go to your profile to authenticate cerificate and use this attribute for the user name.

    Thank you

    Tarik Admani
    * Please note the useful messages *.

  • Cisco ISE posture assessment and client provisioning

    Hello

    I have the Cisco ISE and Cisco IOS device. I configured the RADIUS between these devices.

    Also, I configured RADIUSbetween ISE of Cisco and Cisco ASA. Now I want to know that how to posture assessment for these devices (ISE of Cisco and Cisco ASA or ISE Cisco Cisco IOS). Please give me the steps together for assesment for cisco ios device posture in Cisco ise.

    In addition, please give me related to posture assessment and the provisioning client logs.

    Thanks in advance.

    You can go through the list link below to download a PDF link

    Assessment of the posture with ISE.

    http://www.Cisco.com/Web/CZ/expo2012/PDF/T_SECA4_ISE_Posture_Gorgy_Acs.PDF

    ~ BR
    Jatin kone

    * Does the rate of useful messages *.

  • Integration of CISCO ISE with another controller wireless lan of the seller

    Hi all!

    I am currently working on an assignment and eager to integrate the identity service provider in the network. the only problem is that the deployed wireless network earlier of another provider I just need to know that either ISE has integration with the other controller feature wireless provider and can provide guest access control. The LDAP integration is also required.

    Waiting for help!

    Hello

    According to my knowledge Yes, Cisco ISE can be integrated with another controller wireless LAN of the seller, but limited. (Aruba, Rukus) and if you want to add the external identity group to your network, then LDAP integration is required.

  • Site to Site with ASA and FortiGate

    I have setup a VPN site-to site between my ASA and FortiGate customers. The tunnel rises with success, but we can not pass traffic. When I do a packet capture on my ASA, I see traffic on the port of entry as usual, but on the output port, the source address gets NAT had I checked all statements of NAT, and there is a statement NAT exempted from the entry port to the port of exit and in the VPN configuration.

    Then your oder of NAT statements in probably wrong. The dynamic NAT for outgoing traffic must be at the end (I put them always in article 3), while the Exemption must be at the beginning of Section 1.

  • ISE with WLC AND switches

    Hello

    We run 3xWLC controller with 800 AP using ISE 1.2 for authentication wireless 802. 1 x. I was looking in the config of the ISE and notice of 400 edge cheating only 2x2960s are configured with 802. 1 x (ISE RADIUS config) and SNMP and only 2 of the port is 2 ap tie with swtich remaining ports.and the 3XWLC in network devices.

    I do not understand how an access point is to do this work (802.1 x) because it is location on different site and people are connecting to various different locations. ISE almost run/do 11 876 profiled ends.

    version 12.2
    !
    boot-start-marker
    boot-end-marker
    !
    enable secret 5 $1$ fokm$ lesIWAaceFFs.SpNdJi7t.
    !
    Test-RADIUS username password 7 07233544471A1C5445415F
    AAA new-model
    Group AAA dot1x default authentication RADIUS
    Group AAA authorization network default RADIUS
    Group AAA authorization auth-proxy default RADIUS
    start-stop radius group AAA accounting dot1x default
    start-stop radius group AAA accounting system by default
    !
    !
    !
    !
    AAA server RADIUS Dynamics-author
    Client 10.178.5.152 server-key 7 151E1F040D392E
    Client 10.178.5.153 server-key 7 060A1B29455D0C
    !
    AAA - the id of the joint session
    switch 1 supply ws-c2960s-48 i/s-l
    cooldown critical authentication 1000
    !
    !
    IP dhcp snooping vlan 29,320,401
    no ip dhcp snooping option information
    IP dhcp snooping
    no ip domain-lookup
    analysis of IP device
    !
    logging of the EMP
    !
    Crypto pki trustpoint TP-self-signed-364377856
    enrollment selfsigned
    name of the object cn = IOS - Self - signed - certificate - 364377856
    revocation checking no
    rsakeypair TP-self-signed-364377856
    !
    !
    TP-self-signed-364377856 crypto pki certificate chain
    certificate self-signed 01
    30820247 308201B 0 A0030201 02020101 300 D 0609 2A 864886 F70D0101 04050030
    2 060355 04031325 494F532D 53656 C 66 2 AND 536967 6E65642D 43657274 30312E30
    69666963 33363433 37373835 36301E17 393330 33303130 30303331 0D 6174652D
    305A170D 2E302C06 1325494F 03550403 32303031 30313030 30303030 5A 303031
    532D 5365 6C662D53 69676E65 642D 4365 72746966 69636174 652 3336 34333737
    06092A 86 4886F70D 01010105 38353630 819F300D 00308189 02818100 0003818D
    B09F8205 9DD44616 858B1F49 A27F94E4 9E9C3504 F56E18EB 6D1A1309 15C20A3D
    31FCE168 5A8C610B 7F77E7FC D9AD3856 E4BABDD1 DFB28F54 6C24229D 97756ED4
    975E2222 939CF878 48D7F894 618279CF 2F9C4AD5 4008AFBB 19733DDB 92BDF73E
    B43E0071 C7DC51C6 B9A43C6A FF035C63 B53E26E2 C0522D40 3F850F0B 734DADED
    02030100 01A 37130 03551 D 13 6F300F06 0101FF04 05300301 01FF301C 0603551D
    11041530 13821150 5F494D2B 545F5374 61636B5F 322D312E 301F0603 551D 2304
    18301680 1456F3D9 23759254 57BA0966 7C6C3A71 FFF07CE0 A2301D06 03551D0E
    04160414 56F3D923 75925457 BA09667C 6C3A71FF F07CE0A2 2A 864886 300 D 0609
    F70D0101 5B1CA52E B38AC231 E45F3AF6 12764661 04050003 81810062 819657B 5
    F08D258E EAA2762F F90FBB7F F6E3AA8C 3EE98DB0 842E82E2 F88E60E0 80C1CF27
    DE9D9AC7 04649AEA 51C49BD7 7BCE9C5A 67093FB5 09495971 926542 4 5A7C7022
    8D9A8C2B 794D99B2 3B92B936 526216E0 79 D 80425 12B 33847 30F9A3F6 9CAC4D3C
    7C96AA15 CC4CC1C0 5FAD3B
    quit smoking
    control-dot1x system-auth
    dot1x critical eapol
    !
    pvst spanning-tree mode
    spanning tree extend id-system
    No vlan spanning tree 294-312,314-319,321-335,337-345,400,480,484-493,499,950
    !
    !
    !
    errdisable recovery cause Uni-directional
    errdisable recovery cause bpduguard
    errdisable recovery cause of security breach
    errdisable recovery cause channel-misconfig (STP)
    errdisable recovery cause pagp-flap
    errdisable recovery cause dtp-flap
    errdisable recovery cause link-flap
    errdisable recovery cause FPS-config-incompatibility
    errdisable recovery cause gbic-invalid
    errdisable recovery cause psecure-violation
    errdisable cause of port-mode-failure recovery
    errdisable recovery cause dhcp-rate-limit
    errdisable recovery cause pppoe-AI-rate-limit
    errdisable recovery cause mac-limit
    errdisable recovery cause vmps
    errdisable recovery cause storm-control
    errdisable recovery cause inline-power
    errdisable recovery cause arp-inspection
    errdisable recovery cause loopback
    errdisable recovery cause small-frame
    errdisable recovery cause psp
    !
    internal allocation policy of VLAN ascendant
    !
    !
    interface GigabitEthernet1/0/10
    switchport access vlan 320
    switchport mode access
    IP access-group ACL-LEAVE in
    authentication event fail following action method
    action of death server to authenticate the event permit
    living action of the server reset the authentication event
    multi-domain of host-mode authentication
    open authentication
    authentication order dot1x mab
    authentication priority dot1x mab
    Auto control of the port of authentication
    periodic authentication
    authentication violation replace
    MAB
    dot1x EAP authenticator
    dot1x tx-time 10
    spanning tree portfast
    spanning tree enable bpduguard

    interface GigabitEthernet1/0/16
    switchport access vlan 320
    switchport mode access
    IP access-group ACL-LEAVE in
    authentication event fail following action method
    action of death server to authenticate the event permit
    living action of the server reset the authentication event
    multi-domain of host-mode authentication
    open authentication
    authentication order dot1x mab
    authentication priority dot1x mab
    Auto control of the port of authentication
    periodic authentication
    authentication violation replace
    MAB
    dot1x EAP authenticator
    dot1x tx-time 10
    spanning tree portfast
    spanning tree enable bpduguard
     
    interface GigabitEthernet1/0/24
    switchport access vlan 320
    switchport mode access
    IP access-group ACL-LEAVE in
    authentication event fail following action method
    action of death server to authenticate the event permit
    living action of the server reset the authentication event
    multi-domain of host-mode authentication
    open authentication
    authentication order dot1x mab
    authentication priority dot1x mab
    Auto control of the port of authentication
    periodic authentication
    authentication violation replace
    MAB
    dot1x EAP authenticator
    dot1x tx-time 10
    spanning tree portfast
    spanning tree enable bpduguard
     
    !
    interface GigabitEthernet1/0/33
    switchport access vlan 320
    switchport mode access
    IP access-group ACL-LEAVE in
    authentication event fail following action method
    action of death server to authenticate the event permit
    living action of the server reset the authentication event
    multi-domain of host-mode authentication
    open authentication
    authentication order dot1x mab
    authentication priority dot1x mab
    Auto control of the port of authentication
    periodic authentication
    authentication violation replace
    MAB
    dot1x EAP authenticator
    dot1x tx-time 10
    spanning tree portfast
    spanning tree enable bpduguard
     
    interface GigabitEthernet1/0/34
    switchport access vlan 320
    switchport mode access
    IP access-group ACL-LEAVE in
    authentication event fail following action method
    action of death server to authenticate the event permit
    living action of the server reset the authentication event
    multi-domain of host-mode authentication
    open authentication
    authentication order dot1x mab
    authentication priority dot1x mab
    Auto control of the port of authentication
    periodic authentication
    authentication violation replace
    MAB
    dot1x EAP authenticator
    dot1x tx-time 10
    spanning tree portfast
    spanning tree enable bpduguard
    !
    interface GigabitEthernet1/0/44
    switchport access vlan 320
    switchport mode access
    IP access-group ACL-LEAVE in
    authentication event fail following action method
    action of death server to authenticate the event permit
    living action of the server reset the authentication event
    multi-domain of host-mode authentication
    open authentication
    authentication order dot1x mab
    authentication priority dot1x mab
    Auto control of the port of authentication
    periodic authentication
    authentication violation replace
    MAB
    dot1x EAP authenticator
    dot1x tx-time 10
    spanning tree portfast
    spanning tree enable bpduguard

    !
    interface GigabitEthernet1/0/46
    switchport access vlan 320
    switchport mode access
    IP access-group ACL-LEAVE in
    authentication event fail following action method
    action of death server to authenticate the event permit
    living action of the server reset the authentication event
    multi-domain of host-mode authentication
    open authentication
    authentication order dot1x mab
    authentication priority dot1x mab
    Auto control of the port of authentication
    periodic authentication
    authentication violation replace
    MAB
    dot1x EAP authenticator
    dot1x tx-time 10
    spanning tree portfast
    spanning tree enable bpduguard

    interface GigabitEthernet1/0/48
    switchport access vlan 320
    switchport mode access
    IP access-group ACL-LEAVE in
    authentication event fail following action method
    action of death server to authenticate the event permit
    living action of the server reset the authentication event
    multi-domain of host-mode authentication
    open authentication
    authentication order dot1x mab
    authentication priority dot1x mab
    Auto control of the port of authentication
    periodic authentication
    authentication violation replace
    MAB
    dot1x EAP authenticator
    dot1x tx-time 10
    spanning tree portfast
    spanning tree enable bpduguard
    !
    interface GigabitEthernet1/0/49
    Description link GH
    switchport trunk allowed vlan 1,2,320,350,351,401
    switchport mode trunk
    MLS qos trust dscp
    IP dhcp snooping trust
    !

    interface GigabitEthernet1/0/52
    Description link CORE1
    switchport trunk allowed vlan 1,2,29,277,278,314,320,401
    switchport mode trunk
    MLS qos trust dscp
    IP dhcp snooping trust
    !
    !
    interface Vlan320
    IP 10.178.61.5 255.255.255.128
    no ip-cache cef route
    no ip route cache
    !
    default IP gateway - 10.178.61.1
    IP http server
    IP http secure server
    IP http secure-active-session-modules no
    active session modules IP http no
    !
    !
    Access IP extended ACL-AGENT-REDIRECT list
    deny udp any any domain eq bootps
    permit tcp any any eq www
    permit any any eq 443 tcp
    IP extended ACL-ALLOW access list
    allow an ip
    IP access-list extended by DEFAULT ACL
    allow udp any eq bootpc any eq bootps
    allow udp any any eq field
    allow icmp a whole
    allow any host 10.178.5.152 eq 8443 tcp
    permit tcp any host 10.178.5.152 eq 8905
    allow any host 10.178.5.152 eq 8905 udp
    permit tcp any host 10.178.5.152 eq 8906
    allow any host 10.178.5.152 eq 8906 udp
    allow any host 10.178.5.152 eq 8909 tcp
    allow any host 10.178.5.152 eq 8909 udp
    allow any host 10.178.5.153 eq 8443 tcp
    permit tcp any host 10.178.5.153 eq 8905
    allow any host 10.178.5.153 eq 8905 udp
    permit tcp any host 10.178.5.153 eq 8906
    allow any host 10.178.5.153 eq 8906 udp
    allow any host 10.178.5.153 eq 8909 tcp
    allow any host 10.178.5.153 eq 8909 udp
    refuse an entire ip
    Access IP extended ACL-WEBAUTH-REDIRECT list
    deny ip any host 10.178.5.152
    deny ip any host 10.178.5.153
    permit tcp any any eq www
    permit any any eq 443 tcp

    radius of the IP source-interface Vlan320
    exploitation forest esm config
    logging trap alerts
    logging Source ip id
    connection interface-source Vlan320
    record 192.168.6.31
    host 10.178.5.150 record transport udp port 20514
    host 10.178.5.151 record transport udp port 20514
    access-list 10 permit 10.178.5.117
    access-list 10 permit 10.178.61.100
    Server SNMP engineID local 800000090300000A8AF5F181
    SNMP - server RO W143L355 community
    w143l355 RW SNMP-server community
    SNMP-Server RO community lthpublic
    SNMP-Server RO community lthise
    Server SNMP trap-source Vlan320
    Server SNMP informed source-interface Vlan320
    Server enable SNMP traps snmp authentication linkdown, linkup cold start
    SNMP-Server enable traps cluster
    config SNMP-server enable traps
    entity of traps activate SNMP Server
    Server enable SNMP traps ipsla
    Server enable SNMP traps syslog
    Server enable SNMP traps vtp
    SNMP Server enable traps mac-notification change move threshold
    Server SNMP enable traps belonging to a vlan
    SNMP-server host 10.178.5.152 version 2 c lthise mac-notification
    SNMP-server host 10.178.5.153 version 2 c lthise mac-notification
    !
    RADIUS attribute 6 sur-pour-login-auth server
    Server RADIUS attribute 8 include-in-access-req
    RADIUS attribute 25-application access server include
    dead-criteria 5 tent 3 times RADIUS server
    test the server RADIUS host 10.178.5.152 auth-port 1812 acct-port 1813 username test-RADIUS 7 key 03084F030F1C24
    test the server RADIUS host 10.178.5.153 auth-port 1812 acct-port 1813 username test-RADIUS 7 key 141B060305172F
    RADIUS vsa server send accounting
    RADIUS vsa server send authentication

    any help would be really appreciated.

    I'm not sure that completely understand the question; But if LSE is only political wireless, then none of the wired switches need any configuration of ISE.

    Access points tunnel all wireless traffic to the WLC on CAPWAP (unless you use FlexConnect). This is the configuration 802. 1 x on the WLC that implements policies defined in ISE.

    Switches wired never need to act as an access network (n) device and so do not need to be defined in ISE unless or until you want to apply policies of ISE for wired devices...

  • Cisco ISE - eap-peap and eap - tls

    Hello

    Does anyone have an example of a policy of ISE, where from a WLC authentication requests can be processed by TLS and PEAP?

    I don't seem to get that working, I however do the accident of ISE application with my config that is not the idea.

    If peap uses this identity source, if tls uses 'this profile of authentication certificate '.

    THX

    Don't need to do in politics

    Can create a sequence identity and understand that it contains a certificate OmniPass profile and identity store

    Administration > identity management > identity Source sequences

    Can then select and define the Certfiicate authentication profile for OmniPass based certificate and a list of authentication search

  • Authentication (Windows Server 2013) AD Cisco ISE problem

    Background:

    Has deployed two Cisco ISE 1.1.3. ISE will be used to authenticate users wireless access admin WLC and switches. Database backend is Microsoft running on Windows Server 2012 AD. Existing Cisco ACS 4.2 still running and authenticate users. There are two Cisco WLCs version 7.2.111.3.

    Wireless users authenticates to AD, through works of GBA 4.2. Access admin WLC and switches to the announcement through ISE works. Authentication with PEAP-MSCHAPv2 access and admin PAP/ASCII wireless.

    Problem:

    Wireless users cannot authenticate to the announcement through ISE. This is the error message '11051 RADIUS packet contains invalid state attribute' & '24444 Active Directory failed because of an error that is not specified in the ISE'.

    Conducted a detailed test of the AD of the ISE. The test was a success and the result seems fine except for the below:

    xxdc01.XX.com (10.21.3.1)

    Ping: 0 Mins Ago

    Status: down

    xxdc02.XX.com (10.21.3.2)

    Ping: 0 Mins Ago

    Status: down

    xxdc01.XX.com

    Last success: Thu Jan 1 10:00 1970

    March 11 failure: read 11:18:04 2013

    Success: 0

    Chess: 11006

    xxdc02.XX.com

    Last success: Fri Mar 11 09:43:31 2013

    March 11 failure: read 11:18:04 2013

    Success: 25

    Chess: 11006

    Domain controller: xxdc02.xx.com:389

    Domain controller type: unknown functional level DC: 5

    Domain name: xx.COM

    IsGlobalCatalogReady: TRUE

    DomainFunctionality: 2 = (DS_BEHAVIOR_WIN2003)

    ForestFunctionality: 2 = (DS_BEHAVIOR_WIN2003)

    Action taken:

    Log Cisco ISE and WLC by using the credentials of the AD. This excludes the connection AD, clock and AAA shared secret as the problem.

    (2) wireless authentication tested using EAP-FAST, but same problem occurs.

    (3) detailed error message shows below. This excludes any authentication and authorization policies. Even before hitting the authentication policy, the AD search fails.

    12304 extract EAP-response containing PEAP stimulus / response

    11808 extracted EAP-response containing EAP - MSCHAP VERSION challenge response to the internal method and accepting of EAP - MSCHAP VERSION such as negotiated

    Evaluate the politics of identity

    15006 set default mapping rule

    15013 selected identity Store - AD1

    24430 Authenticating user in Active Directory

    24444 active Directory operation failed because of an error that is not specified in the ISE

    (4) enabled the registration of debugging AD and had a look at the logging. Nothing significant, and no clue about the problem.

    (5) wireless tested on different mobile phones with the same error and laptos

    (6) delete and add new customer/features of AAA Cisco ISE and WLC

    (7) ISE services restarted

    (8) join domain on Cisco ISE

    (9) notes of verified version of ISE 1.1.3 and WLC 7.2.111.3 for any open caveats. Find anything related to this problem.

    10) there are two ISE and two deployed WLC. Tested a different combination of ISE1 to WLC1, ISE1 to WLC2, etc. This excludes a hardware problem of WLC.

    Other possibilities/action:

    1) test it on another version WLC. Will have to wait for approval of the failure to upgrade the WLC software.

    (2) incompatibility between Cisco ISE and AD running on Microsoft Windows Server 2012

    Did he experienced something similar to have ideas on why what is happening?

    Thank you.

    Update:

    (1) built an another Cisco ISE 1.1.3 sever in another data center that uses the same domain but other domain controller. Thai domain controller running Windows Server 2008. This work and successful authentication.

    (2) my colleague tested in a lab environment Cisco ISE 1.1.2 with Windows Server 2012. He has had the same problem as described.

    This leads me to think that there is a compatibility issue of Cisco ISE with Windows Server 2012.



    Yes, it seems that 1.1.3 doesn't support Server 2012 as of yet.

    External identity Source OS/Version

    Microsoft Windows Active Directory 2003 R2 32-bit and 64-bit

    Active Directory Microsoft Windows 2008 32-bit and 64-bit

    Microsoft Windows Active Directory 2008 R2 64-bit only

    Microsoft Windows Active Directory 2003 32-bit only

    http://www.Cisco.com/en/us/docs/security/ISE/1.1/compatibility/ise_sdt.PDF

  • (Between Cisco and Fortigate) IPsec tunnel question

    Hi all

    Im trying to install an IPsec site-to-site between 2 different routers (Cisco 3750 and Fortigate 100a) (R1 & Fortigate100A)

    IPsec, the whole scenario works with the installation.

    But unfortunately the tunnel (between R1 & Fortigate100A) IPsec does not work.

    (Pls look at the attached jpg file)

    The message is received in routers are shown below:

    Cisco: R1:

    % CRYPTO-6-IKMP_MODE_FAILURE: fast mode processing failed with the peer to 192.168.43.75

    FortiGate 100A:

    IKE 0: none established HIS IKE for informational type of d18e1af773e658b9/192.168.43.195:500->192.168.43.75 Exchange 3 cookie d3695c6cea17475a, don't drop

    IKE 0:Cisco - P1:6899: authentication OK

    IKE 0: none established HIS IKE for informational type of d18e1af78ed17bf9/192.168.43.195:500->192.168.43.75 Exchange 3 cookie 414bd35ab92bc4ef, don't drop

    IKE 0:Cisco - P1:6899:Cisco - P2:14802: failure of negotiating quick mode due to the delay of new attempt

    IKE 0:Cisco - P1:6900: authentication OK

    I configured both routers as follows:

    Cisco:

    HostName:R1

    ISAKMP policy 1

    Hash: sha

    Authentication: pre-shared

    Encryption: AES128

    DH group: 2

    Life 86400

    ISAKMP Key: cisco1 address 192.168.43.75

    Crypto IPsec transform-set esp - aes and hmac-sha-esp RIGHT

    Access-list: 101 permit ip 10.0.0.0 0.0.0.255 10.10.10.0 0.0.0.255

    Map R1_to_Fortigate100A 10 IPsec-Isakmp crypto

    defined by peers: 192.168.43.75

    Mailing address 101

    The value transformset: RIGHT

    int fa # 0 / 0 Crypto map R1_to_Fortigate100A

    FortiGate:

    HostName: Fortigate100A

    Phase 1:

    Preshared key: cisco1

    The remote gateway ip address: 192.168.43.195

    mode: aggressive

    Accept any pair

    Proposal P1:

    AES 128 / SHA1

    AES 192 / SHA1

    AES192/SHA 256

    DH: 2

    Keylife: 86400

    Phase2:

    AES 128 / SHA1

    AES 192 / SHA1

    AES192/SHA 256

    Keylife:86400

    Quick mode selector:

    Source address: 10.10.10.0/24

    Destination address: 192.168.43.0/24

    I will be very very very grateful if you informed of my faults possible a solution

    Happy new year

    Ministry of education

    For some time I messed with a fortigate, but I would try first to change the remote address of the phase 2 to 10.0.0,0/24. If this is the statement "interesting traffic", it does not match what you have on the Cisco. After that, try to change the phase 1 Ike mode to something else than "aggressive."

    Sent by Cisco Support technique iPad App

  • Cisco Ise 1.3 with Flex to connect wireless supported function

    Hello

    My environment is formed ROUND of flex-mode connection wireless and cisco Ise 1.3, these features are supported?
    Basic functions of the AAA
    profiling
    posturing
    Substitution VLAN
    Substitution of the ACL
    Comments commissioning

    TrustSec 2.0 this MDC is not supported? someone try this feature?

    These all work with ISE 1.3 and FlexConnect WLAN.

    You need the right license ISE - the type of mobility (wireless) license will cover everything. If you have wired and wireless, then you must have basic (for most features) + more (for profiling) + Apex (for Posturing).

  • SealthWatch intrgration with Cisco ISE-3315

    Hello Experts,

    I have Cisco ISE-3315 version 1.3

    Can I order and SealthWatch Lancop and use it with this series of ISE 3315? Or I must have the SNS?

    Hi Imran-

    3315 unit supports all personas running ISE 1.3

    http://www.Cisco.com/c/en/us/TD/docs/security/ISE/1-3/Release_notes/ise13_rn.html#pgfId-527567

    Now, that being said, don't forget that this devices has a lot less resources compared with the NHU devices. So, if you decided to run all personas on it then you will be greatly limited the number of concurrent endpoints.

    Thank you for evaluating useful messages!

  • The band multiple @domaine used in user name on the integration of commercials with Cisco ISE?

    Hello

    How to remove multiple domain suffixes through ISE with AD user name used as an external identity Source. Username is used in [email protected] / * / format.

    Cisco ISE 1.2 patch introduced 4 Strip prefix or suffix @domaine Kingdom of the username through ISE with AD used as external identity Source. But the documentation is not updated for this feature. I am able to band 1 domain successfully suffix but following conditions listed in the list of suffixes fails to get stripped.

    Any thoughts on the same.

    Thanks Kumar

    In the ISE under Administration > identity management > external identity Sources

    Choose the Active Directory on the left, select your ad server and Advanced settings

    Under identity band of suffix, make sure prefixes band below: is selected (I know, it says prefix).

    In the list of Suffixes box, enter your list of domain suffixes to undress.  The separator character is a comma (,).

    If this does not solve your problem, then I fear that a call to TAC may be in order.

    UPDATE *.

    Spaces are significant characters.  The registration of domains, so as such:

    @domain.com, @domain.local, @testdomain.com

    END UPDATE *.

    Please rate useful messages and mark this question as answered if, in fact, does that answer your question.  Otherwise, feel free to post additional questions.

    Charles Moreton

    Post edited by: Charles Moreton

  • Cisco ISE CLI and GUI password expires

    I got Cisco ISE version 1.1 I am facing a problem with the password CLI and GUI, it expires and I can not connect, I do password reset using the DVD of the ISE.

    I naviguer navigate to the CLI of ISE, then perform the following commands:

    conf t

    password policy

    no password-expiration-enable

    and reset the password of admin GUI, using the command:

    # reset-passwd ise admin request

    from the interface of ISE I delete option for the devil admin account after 45 days.

    but after 60 days, the password expire again.

    kindly advise what to check for this question expires.

    Hello Mostafa,

    Yes, the last answer was more towards past-mgmt GUI because in the majority of cases, it happens with the administrator account on the user interface. I need to know if you've restarted the ISE after disabling the expiration of the CLI, because what I read a few weeks in an internal fault which password policy settings are not preserved on cli after restart so just to check could please check current on CLI w settings / help to see the race. in the password policy.

    ~ BR
    Jatin kone

    * Does the rate of useful messages *.

Maybe you are looking for

  • remove an old printer of the new iMac

    In the search for a new printer, reading the comments, I came across the suggestion to remove the etc. the old printer drivers before installing a new.   Some people have problems with their new printer, before doing this.  How this is done?   Is the

  • In the bar of windows svn revision number

    Hello I think about the possibility of putting on the application toolbar (exe) SVN revision number. I would be characteristic of the usueful to quickly assess, what source application, code review is to build in. What I need is therefore a kind of t

  • is it possible to change the background color of the checkbox control?

    Hello Is this possible in LV to change the background color of the checkbox system? When I try to do this via the Colors property [4] I get error 1131: LabVIEW: You cannot use this property with this control system.Property name: color [4]

  • Receiving a message that my Windows XP is not valid.

    WINDOWS XP Hello, my daughters computer crashed and I bought a cd to fix the problem. When I restarted windows computer thought that my xp was invalid, so I downloaded the validation tool being confident that my system was correct. Microsoft said it

  • Fuze and Rhapsody

    Hey, I ordered my rocket online and did not receive a CD that was supposed to come with her. My friend has a Sansa Fuze and it had an icon on the main menu that says Rhpasody To Go. 1. What is Rhapsody To Go? 2. How can I get Rhapsody To Go to my san