Cisco router 892 IPSec initiator?

Similar Questions

• Cisco router check ipsec site to site vpn tunnetl time?

  I have a Cisco router that has a tunnel vpn to another depending on the location. Now, I want to check how long the VPN for up/construction. I know not if on the SAA, he has this 'sh l2l vpn-sessiondb' command that will allow me to view the tunnel for how long time. Don't seem to find the correct command for Cisco router. If you know the order let me know! Thank you.

  Hello

  I suppose there might be some differences between different platforms (except ASA) VPN or at least it seems to me

  You can try the following command

  View details remote crypto session

  Partial output from one of our routers

  Interface: Port-channel20

  Profile:

  Duration: 01:21:02

  The session state: UP-ACTIVE

  Hope this helps

  -Jouni

• Cisco router access outside the local network interface

  Hi all!

  I have Cisco router 892 (c890-universalk9 - mz.154 - 3.M4.bin) with firewall area and based on routing strategies.

  Everything works fine, but now I need to have the ability to access external router interface IP LAN addresses.

  For example, I PAT 192.168.4.1 port 8443 to the outside interface IP (93.93.93.2 for example) and I need to check LAN 93.93.93.2:8443.

  ! PAT:

  IP nat inside source static tcp 192.168.4.1 8443 93.93.93.1 - extensible 8443 SDM_RMAP_1 road map

  ! DynNat to the internet:

  IP nat inside source overload map route SDM_RMAP_1 interface GigabitEthernet0

  ! Routing policy

  SDM_RMAP_1 allowed 10 route map
  corresponds to the IP 101
  match interface GigabitEthernet0

  ! ACL 101 for routing policy

  access-list 101 deny ip 192.168.3.0 0.0.0.255 192.168.111.0 0.0.0.255
  access-list 101 deny ip 192.168.3.0 0.0.0.255 172.16.192.0 0.0.0.255
  access-list 101 deny ip 192.168.3.0 0.0.0.255 172.16.177.0 0.0.0.255
  access-list 101 deny ip 192.168.3.0 0.0.0.255 172.16.61.0 0.0.0.255
  access-list 101 deny ip 192.168.3.0 0.0.0.255 172.17.19.0 0.0.0.255
  access-list 101 deny ip 192.168.4.0 0.0.0.255 192.168.111.0 0.0.0.255
  access-list 101 deny ip 192.168.3.0 0.0.0.255 host 172.16.194.100
  access-list 101 deny ip 192.168.3.0 0.0.0.255 10.0.0.0 0.255.255.255
  access-list 101 deny ip 192.168.4.0 0.0.0.255 10.0.0.0 0.255.255.255
  access-list 101 deny ip 192.168.4.0 0.0.0.255 host 172.31.255.1
  access-list 101 deny ip 192.168.4.0 0.0.0.255 host 172.16.194.100
  access-list 101 permit ip 192.168.3.0 0.0.0.255 any
  access-list 101 permit ip 192.168.4.0 0.0.0.255 any

  ! ACL on the external interface:

  plug-in software component gi0 extended IP access list
  allow an ip
  allow icmp a whole

  ! External interface

  interface GigabitEthernet0
  Description $ETH - WAN$
  IP 93.93.93.1 255.255.255.240
  IP access-group gi0-in in
  NAT outside IP
  IP virtual-reassembly in
  EXTENT of the Member's area network security
  IP tcp adjust-mss 1452
  automatic duplex
  automatic speed
  card crypto SDM_CMAP_2

  ! Inside DMZ interface vlan:

  interface Vlan4
  IP 192.168.4.254 255.255.255.0
  IP nat inside
  IP virtual-reassembly in
  security of the members of the DMZ
  IP tcp adjust-mss 1452

  ! Allow outbound traffic to DMZ to Internet:

  Allow_All_ACL-DMZ extended IP access list
  allow an esp
  permit tcp host 192.168.4.1 host 192.168.111.2 eq 1521
  refuse the 192.168.4.0 ip 0.0.0.255 192.168.111.0 0.0.0.255
  refuse the 192.168.4.0 ip 0.0.0.255 172.17.19.0 0.0.0.255
  allow icmp 192.168.4.0 0.0.0.255 any
  ip licensing 192.168.4.0 0.0.0.255 any

  ! Allow incoming traffic from the Internet to DMZ:

  WAN_DMZ_ACL extended IP access list
  allow tcp any a Workbench
  permit tcp any any eq ftp
  permit tcp any any eq 990
  permit tcp everything any 51000 53000 Beach
  permit tcp any any eq 995
  permit tcp any any eq 465
  permit tcp any any eq www
  permit any any eq 443 tcp
  allow icmp a whole
  allow an esp
  permit any any eq non500-isakmp udp
  host ip 212.98.162.139 permit 192.168.4.0 0.0.0.255
  IP 81.30.80.0 allow 0.0.0.255 any
  IP 192.168.111.0 allow 0.0.0.255 192.168.4.0 0.0.0.255
  IP 172.17.19.0 allow 0.0.0.255 192.168.4.0 0.0.0.255
  host ip 172.16.194.100 permit 192.168.4.0 0.0.0.255
  host ip 172.31.255.1 permit 192.168.4.0 0.0.0.255
  permit ip host 172.31.255.1 172.17.193.100
  refuse an entire ip

  ! Focus on the area of firewall:

  type of class-card inspect entire game DMZ_WAN_CLASS
  match the group-access name DMZ Allow_All_ACL

  type of class-card inspect entire game WAN_DMZ_CLASS
  match the name of group-access WAN_DMZ_ACL

  type of policy-card inspect DMZ_WAN_POLICY
  class type inspect DMZ_WAN_CLASS
  inspect
  class class by default
  drop

  type of policy-card inspect WAN_DMZ_POLICY
  class type inspect WAN_DMZ_CLASS
  inspect
  class class by default
  drop

  the DMZ security

  
  area WAN security

  Security WAN_DMZ of the pair area source destination WAN DMZ
  type of service-strategy inspect WAN_DMZ_POLICY
  destination of DMZ_WAN source DMZ area pair WAN security
  type of service-strategy inspect DMZ_WAN_POLICY

  Maybe someone can help me to make Cisco to allow ports outside LAN using a NAT?

  I did this on Mikrotik easily = |

  It is due to the fact that they do not allow "hair pinning" by default, once this is configured, it will work.

  Martin

• Problems to connect via the Cisco VPN client IPSec of for RV180W small business router

  Hello

  I tried to configure my router Cisco of RV180W as a customer VPN IPSec, but have encountered a problem that I hope someone can help me with. "" I managed to do the work of configuration so that the Cisco's VPN IPSec client authenticates successfully with the XAUTH user, I put on the router, but during the negotiation, the client ends with the following, which appears several times on the router error message: ' Mar 20 Oct 19:41:53 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [34360] has no config mode.

  I've read around the internet and a number of people seem to say that the Cisco VPN Client is not compatible with the router, but the same thing happens to my iPhone VPN client.

  Is it possible that this can be implemented? Below, I have attached the full configuration files and the log files. Thank you much in advance.

  Router log file (I changed the IP addresses > respectively as well as references to MAC addresses)

  Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: floating ports NAT - T with counterpart > [44074]
  Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] WARNING: notification to ignore INITIAL-CONTACT > [44074] because it is admitted only after the phase 1.
  Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: NAT - D payload does not match for > [4500]
  Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: NAT - D payload does not match for > [44074]
  Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: received unknown Vendor ID
  Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: received Vendor ID: CISCO-UNITY
  Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: NAT detected: is located behind a device. NAT and alsoPeer is behind a NAT device
  Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: request sending Xauth for > [44074]
  Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: ISAKMP Security Association established for > [4500] -> [44074] with spi =>.
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: receives the type of the attribute 'ISAKMP_CFG_REPLY' of > [44074]
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: login successful for the user "myusername".
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: myusername XAuthUser connected from the IP >
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: sending of information Exchange: Notify payload [10381]
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: receives the type of the attribute 'ISAKMP_CFG_REQUEST' of > [44074]
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] WARNING: ignored attribute 5
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] WARNING: attribute ignored 28683
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no mode config
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] WARNING: attribute ignored 28684
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no mode config
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: remove the invalid payload with doi:0.
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: purged-Association of ISAKMP security with proto_id = ISAKMP and spi =>.
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: myusername XAuthUser Logged Out of the IP >
  Mar 20 Oct 20:03:16 2015 (GMT + 0000): [r1] [IKE] INFO: ISAKMP Security Association deleted for > [4500] -> [44074] with spi =>

  The router configuration

  screen_shot_10-20 - 15_at_09.00_pm.png

  

  IKE policy

  screen_shot_10-20 - 15_at_09.00_pm_001.png

  

  screen_shot_10-20 - 15_at_09.01_pm.png

  

  VPN strategy

  screen_shot_10-20 - 15_at_09.02_pm.png

  

  screen_shot_10-20 - 15_at_09.02_pm_001.png

  

  Client configuration

  Hôte : < router="" ip=""> >

  Authentication group name: remote.com

  Password authentication of the Group: mysecretpassword

  Transport: Enable Transparent Tunneling; IPSec over UDP (NAT/PAT)

  Username: myusername

  Password: mypassword

  Please contact Cisco.

  Correct, the RV180 is not compatible with the Cisco VPN Client.  The Iphone uses the Cisco VPN Client.

  You can use the PPTP on the RV180 server to connect a PPTP Client.

  In addition, it RV180 will allow an IPsec connection to third-party customers 3.  Greenbow and Shrew Soft are 2 commonly used clients.

• L2TP/ipsec passthrough firewall of cisco router

  Hello! I have the following problem.

  External network users wish to connect internal Windows to network and share resources 2012 (start the software, files, etc)

  So it's time to deploy a vpn server and as I did not have a free license to run on my windows 2012, I decided to use my qnap for it (because it has this built-in feature) so I chose l2tp/ipsec and tested on the laboratory at home with simple tplink router with upnp function and it worked like a charm.

  However, in the real production environment, I need to use the cisco router, and this is how the story begins ;)

  Thus, clients with their machines say (7, 8.1, 10) must pass router cisco (with nat) firewall and access a vpn server and the internal network on qnap.

  I googled for sample configuration, but most of them related to the configuration of the router as a vpn server, and I want to achieve is to make my pass router vpn traffic. Once I found the same sample of pptp config, I have modified it a bit, but do not know if it works because I have not yet tested.

  In any case, could you check my config and see if it's ok? I'm doing a static nat for vpn 192.168.5.253 server to external address?

  Also, here is a short pattern

  vpn client VPN server (win 7,8,10)---routeur cisco 1921 - qnap)

  xxx.194 cloud 5,254 5.253 (internal network)

  test #show runn
  Building configuration...

  Current configuration: 3611 bytes
  !
  ! Last modified at 19:31:01 UTC Wednesday, may 4, 2016 configuration by
  !
  version 15.4
  horodateurs service debug datetime msec
  Log service timestamps datetime msec
  encryption password service
  !
  hostname test
  !
  boot-start-marker
  boot-end-marker
  !
  !
  enable secret $5
  !
  No aaa new-model
  !
  !
  !
  !
  !
  !
  !
  !
  !
  !
  !
  DHCP excluded-address IP 192.168.5.200 192.168.5.254
  DHCP excluded-address IP 192.168.5.1 192.168.5.189
  !
  pool dhcp IP network
  network 192.168.5.0 255.255.255.0
  router by default - 192.168.5.254
  network domain name
  xxx.x.xxx.244 DNS server
  !
  !
  !
  IP domain name temp
  IP cef
  No ipv6 cef
  !
  Authenticated MultiLink bundle-name Panel
  !
  CTS verbose logging
  !
  !
  license udi pid CISCO1921/K9 sn xxxxxx
  licence start-up module c1900 technology-package securityk9
  !
  !
  username secret abc 5
  username privilege 15 7 cisco password
  !
  redundancy
  !
  !
  !
  !
  !
  property intellectual ssh version 2
  !
  type of class-card inspect entire game cm_helpdek_protocols
  http protocol game
  https protocol game
  ssh protocol game
  type of class-card inspect entire game cm_gre_protocols
  Access-group name WILL
  type of class-card inspect entire game cm_icmp
  group-access icmp name game
  type of class-card inspect the correspondence cm_helpdesk
  match the name of group-access helpdesk
  type of class-card inspect entire game inside_to_outside
  h323 Protocol game
  match Protocol pptp
  ftp protocol game
  tcp protocol match
  udp Protocol game
  match icmp Protocol
  !
  type of policy-card inspect pm_outside_to_inside
  class type inspect cm_gre_protocols
  Pass
  class type inspect cm_icmp
  inspect
  class type inspect cm_helpdesk
  inspect
  class class by default
  Drop newspaper
  type of policy-card inspect pm_inside_to_outside
  class type inspect inside_to_outside
  inspect
  class type inspect cm_gre_protocols
  Pass
  class class by default
  Drop newspaper
  !
  area inside security
  Description inside the zone of confidence
  security of the outside area
  Outside the untrusted area description
  source of zonep_insiede_to_outside security pair area inside the destination outside
  type of service-strategy inspect pm_inside_to_outside
  source of zonep_outside_to_inside security zone-pair outside the destination inside
  type of service-strategy inspect pm_outside_to_inside
  !
  !
  !
  !
  !
  !
  !
  !
  !
  !
  the Embedded-Service-Engine0/0 interface
  no ip address
  Shutdown
  !
  interface GigabitEthernet0/0
  Description 'LAN '.
  IP 192.168.5.254 255.255.255.0
  IP nat inside
  IP virtual-reassembly in
  security of the inside members area
  automatic duplex
  automatic speed
  !
  interface GigabitEthernet0/1
  Description "WAN CID: xxxxx".
  IP address xxx.xxx.xxx.194 255.255.255.252
  NAT outside IP
  IP virtual-reassembly in
  security of the outside Member area
  automatic duplex
  automatic speed
  !
  IP forward-Protocol ND
  !
  IP http server
  local IP http authentication
  no ip http secure server
  !
  IP nat pool network xxx.xxx.xxx.201 xxx.xxx.xxx.201 netmask 255.255.255.248
  IP nat inside source list 1 pool overload the network
  IP route 0.0.0.0 0.0.0.0 xxx.xxx.xxx.193
  !
  GRE extended IP access list
  Note ACL to allow ACCORD of PPTP OUTBOUND
  allow a gre
  permit any any eq udp 1701
  allow udp any any eq isakmp
  permit any any eq non500-isakmp udp
  helpdesk extended IP access list
  IP enable any host 192.168.5.253
  icmp extended IP access list
  allow icmp any host 192.168.5.253
  !
  !
  !
  access-list 1 permit 192.168.5.0 0.0.0.255
  !
  control plan
  !
  !
  !
  Line con 0
  local connection
  line to 0
  line 2
  no activation-character
  No exec
  preferred no transport
  transport output pad telnet, rlogin xxxxx
  StopBits 1
  line vty 0 4
  local connection
  transport input telnet ssh
  !
  Scheduler allocate 20000 1000
  !
  end

  Kind regards

  Andrew

  Once the client has been connected to the VPN, you want traffic back to flow to the client. Which can be easily received with "inspect".

  And from the point of view of the firewall, you do not have ESP-traffic (which would be the IP/50). You have only UDP traffic (initially UDP/500 which goes into UDP/4500)

  And you are right with your last ACE. That of a lot to permissive and not necessary for this function.

• How to disable a particular IPSec tunnel on Cisco router

  Hi guys,.

  Someone knows a way to termporarily disable an IPSec tunnel on a Cisco router provided individual:

  -No configuration changes

  -Without affecting the other IPSec tunnels running

  -GRE is not used, so there is no tunnel interface to close

  Or in any event nearest to you to meet the requirement above?

  Thank you

  Andrew

  Andrew,

  There is no way to 'turn off' the tunnel without changing the config.

  I think the easiest would be to get the card crypto for this particular tunnel and remove the peer or the ACL:

  for example:

  labmap 10 ipsec-isakmp crypto map

  no counterpart set 10.0.0.1

  labmap 10 ipsec-isakmp crypto map

  no correspondence address 100

  or you can remove the key isakmp for this tunnel, that would, for example:

  No cisco123 key crypto isakmp 10.0.0.1 address

  That would prevent the tunnel to come without affecting the other tunnels.

  I hope this helps.

  Raga

• VPN between ASA and cisco router [phase2 question]

  Hi all

  I have a problem with IPSEC VPN between ASA and cisco router

  I think that there is a problem in the phase 2

  Can you please guide me where could be the problem.
  I suspect questions ACL on the router, but I cannot fix. ACL on the router is specified below

  Looking forward for your help

  Phase 1 is like that

  Cisco_router #sh crypto isakmp his

  IPv4 Crypto ISAKMP Security Association
  status of DST CBC State conn-id slot
  78.x.x.41 87.x.x.4 QM_IDLE 2006 0 ACTIVE

  and ASA

  ASA # sh crypto isakmp his

  ITS enabled: 1
  Generate a new key SA: 0 (a tunnel report Active 1 and 1 to generate a new key during the generate a new key)
  Total SA IKE: 1

  1 peer IKE: 78.x.x.41
  Type: L2L role: initiator
  Generate a new key: no State: MM_ACTIVE

  Phase 2 on SAA

  ASA # sh crypto ipsec his
  Interface: Outside
  Tag crypto map: Outside_map, seq num: 20, local addr: 87.x.x.4

  Outside_cryptomap_20 ip 172.19.209.0 access list allow 255.255.255.0 172.
  19.194.0 255.255.255.0
  local ident (addr, mask, prot, port): (172.19.209.0/255.255.255.0/0/0)
  Remote ident (addr, mask, prot, port): (172.19.194.0/255.255.255.0/0/0)
  current_peer: 78.x.x.41

  #pkts program: 8813, #pkts encrypt: 8813, #pkts digest: 8813
  #pkts decaps: 0, #pkts decrypt: 0, #pkts check: 0
  compressed #pkts: 0, unzipped #pkts: 0
  #pkts uncompressed: 8813, model of #pkts failed: 0, #pkts Dang failed: 0
  #send errors: 0, #recv errors: 0

  local crypto endpt. : 87.x.x.4, remote Start crypto. : 78.x.x.41

  Path mtu 1500, fresh ipsec generals 58, media, mtu 1500
  current outbound SPI: C96393AB

  SAS of the esp on arrival:
  SPI: 0x3E9D820B (1050509835)
  transform: esp-3des esp-md5-hmac no
  running parameters = {L2L, Tunnel}
  slot: 0, id_conn: 7, crypto-card: Outside_map
  calendar of his: service life remaining (KB/s) key: (4275000/3025)
  Size IV: 8 bytes
  support for replay detection: Y
  outgoing esp sas:
  SPI: 0xC96393AB (3378746283)
  transform: esp-3des esp-md5-hmac no
  running parameters = {L2L, Tunnel}
  slot: 0, id_conn: 7, crypto-card: Outside_map
  calendar of his: service life remaining (KB/s) key: (4274994/3023)
  Size IV: 8 bytes
  support for replay detection: Y

  Phase 2 on cisco router

  protégé of the vrf: (none)
  local ident (addr, mask, prot, port): (172.19.209.0/255.255.255.0/0/0)
  Remote ident (addr, mask, prot, port): (172.19.194.0/255.255.255.0/0/0)
  current_peer 87.x.x.4 port 500
  LICENCE, flags is {origin_is_acl},
  #pkts program: encrypt 0, #pkts: 0, #pkts digest: 0
  #pkts decaps: 0, #pkts decrypt: 0, #pkts check: 0
  compressed #pkts: 0, unzipped #pkts: 0
  #pkts uncompressed: 0, #pkts compr. has failed: 0
  #pkts not unpacked: 0, #pkts decompress failed: 0
  Errors #send 0, #recv 0 errors

  local crypto endpt. : 78.x.x.41, remote Start crypto. : 87.x.x.4
  Path mtu 1452, ip mtu 1452, ip mtu BID Dialer0
  current outbound SPI: 0x0 (0)

  SAS of the esp on arrival:

  the arrival ah sas:

  SAS of the CFP on arrival:

  outgoing esp sas:

  outgoing ah sas:

  outgoing CFP sas:

  protégé of the vrf: (none)
  local ident (addr, mask, prot, port): (172.19.194.0/255.255.255.0/0/0)
  Remote ident (addr, mask, prot, port): (172.19.209.0/255.255.255.0/0/0)
  current_peer 87.x.x.4 port 500
  LICENCE, flags is {origin_is_acl},
  #pkts program: encrypt 0, #pkts: 0, #pkts digest: 0
  #pkts decaps: 8947, #pkts decrypt: 8947, #pkts check: 8947
  compressed #pkts: 0, unzipped #pkts: 0
  #pkts uncompressed: 0, #pkts compr. has failed: 0
  #pkts not unpacked: 0, #pkts decompress failed: 0
  Errors #send 0, #recv 0 errors

  local crypto endpt. : 78.x.x.41, remote Start crypto. : 87.x.x.4
  Path mtu 1452, ip mtu 1452, ip mtu BID Dialer0
  current outbound SPI: 0x3E9D820B (1050509835)

  SAS of the esp on arrival:
  SPI: 0xC96393AB (3378746283)
  transform: esp-3des esp-md5-hmac.
  running parameters = {Tunnel}
  Conn ID: 29, flow_id: Motorola SEC 1.0:29, card crypto: mycryptomap
  calendar of his: service life remaining (k/s) key: (4393981/1196)
  Size IV: 8 bytes
  support for replay detection: Y
  Status: ACTIVE

  the arrival ah sas:

  SAS of the CFP on arrival:

  outgoing esp sas:
  SPI: 0x3E9D820B (1050509835)
  transform: esp-3des esp-md5-hmac.
  running parameters = {Tunnel}
  Conn ID: 30, flow_id: Motorola SEC 1.0:30, card crypto: mycryptomap
  calendar of his: service life remaining (k/s) key: (4394007/1196)
  Size IV: 8 bytes
  support for replay detection: Y
  Status: ACTIVE

  outgoing ah sas:

  outgoing CFP sas:

  VPN configuration is less in cisco router

  access-list 101 permit ip 172.19.194.0 0.0.0.255 172.19.206.0 0.0.0.255 connect
  access-list 101 permit ip 172.19.206.0 0.0.0.255 172.19.194.0 0.0.0.255 connect
  access-list 101 permit ip 172.19.194.0 0.0.0.255 172.19.203.0 0.0.0.255 connect
  access-list 101 permit ip 172.19.203.0 0.0.0.255 172.19.194.0 0.0.0.255 connect
  access-list 101 permit ip 172.19.194.0 0.0.0.255 172.19.209.0 0.0.0.255 connect
  access-list 101 permit ip 172.19.209.0 0.0.0.255 172.19.194.0 0.0.0.255 connect

  access-list 105 deny ip 172.19.194.0 0.0.0.255 172.19.206.0 0.0.0.255 connect
  access-list 105 deny ip 172.19.206.0 0.0.0.255 172.19.194.0 0.0.0.255 connect
  access-list 105 deny ip 172.19.194.0 0.0.0.255 172.19.203.0 0.0.0.255 connect
  access-list 105 deny ip 172.19.203.0 0.0.0.255 172.19.194.0 0.0.0.255 connect
  access-list 105 deny ip 172.19.194.0 0.0.0.255 172.19.209.0 0.0.0.255 connect
  access-list 105 deny ip 172.19.209.0 0.0.0.255 172.19.194.0 0.0.0.255 connect

  sheep allowed 10 route map
  corresponds to the IP 105

  Crypto ipsec transform-set esp-3des esp-md5-hmac mytransformset

  mycryptomap 100 ipsec-isakmp crypto map
  the value of 87.x.x.4 peer
  Set transform-set mytransformset
  match address 101

  crypto ISAKMP policy 100
  BA 3des
  md5 hash
  preshared authentication
  Group 2
  ISAKMP crypto key xxx2011 address 87.x.x.4

  Your permit for 105 ACL statement should be down is changed to match because it is the most general ACL.

  You currently have:

  Extend the 105 IP access list
  5 permit ip 172.19.194.0 0.0.0.255 (18585 matches)
  10 deny ip 172.19.194.0 0.0.0.255 172.19.206.0 0.0.0.255 connect
  30 deny ip 172.19.194.0 0.0.0.255 172.19.203.0 0.0.0.255 connect
  50 deny ip 172.19.194.0 0.0.0.255 172.19.209.0 0.0.0.255 connect

  It should be:

  Extend the 105 IP access list
  10 deny ip 172.19.194.0 0.0.0.255 172.19.206.0 0.0.0.255 connect
  30 deny ip 172.19.194.0 0.0.0.255 172.19.203.0 0.0.0.255 connect
  50 deny ip 172.19.194.0 0.0.0.255 172.19.209.0 0.0.0.255 connect

  IP 172.19.194.0 allow 60 0.0.0.255 (18585 matches)

  To remove it and add it to the bottom:

  105 extended IP access list

  not 5

  IP 172.19.194.0 allow 60 0.0.0.255 any

  Then ' delete ip nat trans. "

  and it should work now.

• VPN - Pix 515e for Cisco router

  I have the following Setup and I can't seem to get the next tunnel. My end is a PIX 515e race 7.2 (4). The other end is a Cisco router-not sure of the model or version of the IOS.

  PIX:

  90 extended access-list allow ip host a.a.a.a host b.b.b.b

  NAT (inside) - 0-90 access list

  correspondence address card crypto mymap 20 90
  card crypto mymap 20 peers set x.x.x.x
  map mymap 20 set transformation-strong crypto
  mymap outside crypto map interface
  ISAKMP crypto identity hostname
  crypto ISAKMP allow outside
  crypto ISAKMP policy 8
  preshared authentication
  3des encryption
  sha hash
  Group 2
  life 86400

  tunnel-group x.x.x.x type ipsec-l2l
  tunnel-group ipsec-attributes x.x.x.x
  pre-shared key 12345

  Router:

  / * Style definitions * / table. MsoNormalTable {mso-style-name : « Table Normal » ; mso-tstyle-rowband-taille : 0 ; mso-tstyle-colband-taille : 0 ; mso-style-noshow:yes ; mso-style-priorité : 99 ; mso-style-qformat:yes ; mso-style-parent : » « ;" mso-rembourrage-alt : 0 à 5.4pt 0 à 5.4pt ; mso-para-margin : 0 ; mso-para-marge-bottom : .0001pt ; mso-pagination : widow-orphelin ; police-taille : 11.0pt ; famille de police : « Calibri », « sans-serif » ; mso-ascii-font-family : Calibri ; mso-ascii-theme-font : minor-latin ; mso-fareast-font-family : « Times New Roman » ; mso-fareast-theme-font : minor-fareast ; mso-hansi-font-family : Calibri ; mso-hansi-theme-font : minor-latin ; mso-bidi-font-family : « Times New Roman » ; mso-bidi-theme-font : minor-bidi ;} / * Définitions de style * / table. MsoNormalTable {mso-style-name : « Table Normal » ; mso-tstyle-rowband-taille : 0 ; mso-tstyle-colband-taille : 0 ; mso-style-noshow:yes ; mso-style-priorité : 99 ; mso-style-qformat:yes ; mso-style-parent : » « ;" mso-rembourrage-alt : 0 à 5.4pt 0 à 5.4pt ; mso-para-margin : 0 ; mso-para-marge-bottom : .0001pt ; mso-pagination : widow-orphelin ; police-taille : 11.0pt ; famille de police : « Calibri », « sans-serif » ; mso-ascii-font-family : Calibri ; mso-ascii-theme-font : minor-latin ; mso-fareast-font-family : « Times New Roman » ; mso-fareast-theme-font : minor-fareast ; mso-hansi-font-family : Calibri ; mso-hansi-theme-font : minor-latin ; mso-bidi-font-family : « Times New Roman » ; mso-bidi-theme-font : minor-bidi ;}

  SDM_5 extended IP access list

  permit ip host b.b.b.b host a.a.a.a

  ISAKMP crypto key 12345 address y.y.y.y no.-xauth

  map SDM_CMAP_1 5 ipsec-isakmp crypto

  Description vpn for laboratory

  defined peer y.y.y.y

  game of transformation-ESP-3DES-SHA

  match address SDM_5

  I'm running him debugs following:

  Debug crypto ipsec enabled at level 1
  ISAKMP crypto debugging enabled at level 1

  I get the following debug output:

  August 16-04:16:10 [IKEv1]: IP = x.x.x.x, counterpart of drop table counterpart, didn't match!
  August 16-04:16:10 [IKEv1]: IP = x.x.x.x, error: cannot delete PeerTblEntry

  Isa HS her

  IKE Peer: x.x.x.x
  Type: user role: initiator
  Generate a new key: no State: MM_WAIT_MSG2

  Any ideas?

  Thank you

  Dave

  If you see the MM_WAIT_MSG2, which means that her counterpart (the other side) does not answer and this side where you can see the status MM_WAIT_MSG2 sent the first message IKE, however, did not hear of the peer.

  You can check if UDP/500 is stuck on the way between the 2 sites.

  Try running traffic on the other side and see if you also get the same status of MM_WAIT_MSG2. If you do, that confirms 100% 500/UDP is blocked on the way between the 2 sites.

• NPS Windows Help for authentication of aaa for Cisco router - is it safe?

  I am very confused about how all this works and was hoping someone could help me.

  I followed a bunch of tutorials online for authentication RADIUS of installation on a Cisco router and he did to a NPS Windows Server. Now I can ssh into the router my AD account.

  Now that I got it to work, I go to the settings to make sure everything is secure.

  On my router, the config is pretty simple:

  aaa new-modelaaa group server radius WINDOWS_NPSserver-private 123.123.123.123 auth-port 1812 acct-port 1813 key mykeyaaa authentication login default local group WINDOWS_NPS
  
  ip domain-name MyDomcrypto key generate rsa
  
  (under vty and console)# login authentication default
  On the NPS Windows:
  I created a new RADIUS client for the router.
  Created a secret shared and specified Cisco as the name of the seller.
  Created a new strategy of network with my desired conditions.
  And now the frame of the configuration of the network policy that worries me:
  
  
  So initially I thought my AD credentials were being sent over the wire in plain text, but I did a capture and saw this:
  
  
  
  capture.jpg
  
          
      
  
  
  How is my password being encrypted and how strong is the encryption?
  
  Another thing is how can I configure aaa authentication with mschapv2? The documentation I saw for mschapv2 uses the "ppp authentication ms-chap-v2" command, but I'm not using ppp I'm using aaa with a radius server.
   
  			 
  Hello
  RADIUS encrypts the password, but sends the username in clear. GANYMEDE encrypts the user name and password.
  You can find the encryption used by RADIUS in the RFC scheme:
  https://Tools.ietf.org/html/rfc2865#page-27
  MS-Chap-V2 is used for the authentication of users such as the remote access and vpn, not management switch
  Thank you
  John
  		   

• Cisco's VPN IPSec help please

  Hi all

  I have 3 sites, the main site has a cisco firewall mikrotik router.

  There is a vpn ipsec existing between the cisco router and another router cisco on the site of the 2nd and it works well.

  Now, I've added an another vpn between a 3rd site and main site. The router on the 3rd site is a mikrotik firewall.

  I had the vpn on the main site and the 3rd site where the mikrotik firewall is and it worked well.

  then for some reason, the vpn with the 3rd site has failed and I could not get it working again.

  When looking for answers, I see that the vpn for the 3rd site States the following:

  #pkts program: 46, #pkts encrypt: 46, #pkts digest: 46
  #pkts decaps: 0, #pkts decrypt: 0, #pkts check: 0

  It seems that no traffic is coming back to the cisco

  I also found the following output below to diagnose the problem.

  It seems that there is communication, but if I read this right, it looks like the cisco established a new number but the other end is not the new number

  new node-1868419487

  node-1868419487 error suppression FALSE "Information (in) condition 1" pattern

  Any help would be appreciated.

  * 02:49:51.911 Jul 22: ISAKMP: (2060): purge the node-1140469772

  * 02:49:59.723 Jul 22: ISAKMP: DPD received message KMI.

  * 02:49:59.723 Jul 22: ISAKMP: node set 1053074288 to QM_IDLE

  * 02:49:59.723 Jul 22: ISAKMP: (2060): Protocol for sending INFORMER DPD/R_U_THERE 1

  SPI 2273844328, message ID = 1053074288

  * 02:49:59.723 Jul 22: ISAKMP: (2060): seq. no 0x645EC368

  * 02:49:59.723 Jul 22: ISAKMP: (2060): my_port of x.x.x.127 package sending 5

  peer_port 00 500 (R) QM_IDLE

  * 02:49:59.723 Jul 22: ISAKMP: (2060): sending a packet IPv4 IKE.

  * 02:49:59.723 Jul 22: ISAKMP: (2060): purge the node 1053074288

  * 02:49:59.767 Jul 22: ISAKMP (2060): packet received dport x.x.x.127

  500 sport Global 500 (R) QM_IDLE

  * 02:49:59.767 Jul 22: ISAKMP: node set-1868419487 to QM_IDLE

  * 02:49:59.771 Jul 22: ISAKMP: (2060): HASH payload processing. Message ID = 24265

  47809

  * 02:49:59.771 Jul 22: ISAKMP: (2060): treatment of the NOTIFY DPD/R_U_THERE_ACK protoco

  l 1

  0, message ID SPI = 2426547809, a = 0x8705F854

  * 02:49:59.771 Jul 22: ISAKMP: (2060): DPO/R_U_THERE_ACK received from the peer 125,23

  6.211.127, sequence 0x645EC368

  * 02:49:59.771 Jul 22: ISAKMP: (2060): node-1868419487 FALSE reason for deletion error

  "Information (in) condition 1"

  * 02:49:59.771 Jul 22: ISAKMP: (2060): entry = IKE_MESG_FROM_PEER, IKE_INFO_NOTIFY

  * 02:49:59.771 Jul 22: ISAKMP: (2060): former State = new State IKE_P1_COMPLETE = IKE

  _P1_COMPLETE

  * 02:50:01.111 Jul 22: ISAKMP: (2060): purge the node-1201068805

  Comparing encrypt of 46 to 47436 counters, it seems that router is ecncrypting the traffic, but we do not get any interesting traffic on the remote side.

  Most likely, you might want to check on the remote site, if you see counters increment in parallel decryption and encryption of the counters are incrementing or not.

  On the router IOS, if are incrementing counters encrypt, and confirm that you have not any tunnel existing before the router can be seen same proxy IDs, which is already negotiated with other peer.

  Finally, please make sure that the ESP, 50 protocol traffic is not blocked in transit.
  I hope this helps.

  Kind regards
  Dinesh Moudgil

  PS Please rate helpful messages.

• Launch a VPN from a cisco router on the LAN behind the ASA?

  We currently have an ASA with used site to site VPN and anyconnect VPN. We received a third party cisco router that will be used to launch their own VPN site to site of inside our LAN to their local network through our ASA.

  1 NAT Traversal would call our ASA? 5540 (config) #crypto isakmp nat-traversal

  2. the ports listed below interfere with site to site VPN and anyconnect VPN ports?

  SSH

  -allow access of xxxxx on TCP Port 22

  ICMP

  -allow access of xxxxx - Protocol No. 1

  ISAKMP

  -allow access to xxxxx on UDP Port 500, also add UDP 4500 for NAT - T

  ESP

  -allow access to xxxxx - protocol 50

  Port of certificate:

  -allow access to xxxxx on port TCP 8080

  NTP port:

  -allow access to xxxxx on port UDP 123

  Hi Michael,

  1-

  NAT - T is only required if one of the sites is behind NAT.

  NAT - T allows to establish a connection through a NAT device counterparts IPsec. It does this by encapsulating IPsec datagrams UDP traffic, using the port 4500, which provides information of port NAT. NAT - T devices automatically detects all NAT devices and only encapsulates IPsec traffic when necessary. This feature is disabled by default.

  http://www.Cisco.com/en/us/docs/security/ASA/asa84/configuration/guide/vpn_ike.html#wp1120836

  2-

  ISAKMP

  -allow access to xxxxx on UDP Port 500, also add UDP 4500 for NAT - T

  ESP

  -allow access to xxxxx - protocol 50

  The ports above are those used for the IPsec VPN, SSL AnyConnect does not use them.

  Let me know.

  Thank you.

  Portu.

  Please note all messages that you be useful.

  Post edited by: Javier Portuguez

• Need some advice about the VPN between local Cisco router and remote Watchguard

  Hi all

  I am configuring a Cisco 887 to VPN router to a device of watchguard at the remote site.

  From what I understand, the VPN tunnel is in PLACE. I can ping to the remote server on the 192.168.110.0 of the network, but whenever I try to navigate to it on the local server, it wouldn't work.

  I ping the remote server via the IP address on the local server, but not on the Cisco router. Is - will this work as expected?

  --------------------------------------------------------------------------------------

  R5Router #sh crypto isakmp his

  IPv4 Crypto ISAKMP Security Association

  DST CBC conn-State id

  110.142.127.237 122.3.112.10 QM_IDLE 2045 ACTIVE

  IPv6 Crypto ISAKMP Security Association

  --------------------------------------------------------------------------------------

  R5Router #sh encryption session

  Current state of the session crypto

  Interface: Virtual-Access2

  The session state: down

  Peer: 122.3.112.10 port 500

  FLOW IPSEC: allowed ip 192.168.0.0/255.255.255.0 192.168.110.0/255.255.255.0

  Active sAs: 0, origin: card crypto

  FLOW IPSEC: allowed 1 192.168.0.0/255.255.255.0 192.168.110.0/255.255.255.0

  Active sAs: 0, origin: card crypto

  FLOW IPSEC: allowed 6 192.168.0.0/255.255.255.0 192.168.110.0/255.255.255.0

  Active sAs: 0, origin: card crypto

  FLOW IPSEC: allowed ip host 122.3.112.10 192.168.0.0/255.255.255.0

  Active sAs: 0, origin: card crypto

  Interface: Dialer0

  The session state: UP-ACTIVE

  Peer: 122.3.112.10 port 500

  IKEv1 SA: local 110.142.127.237/500 remote 122.3.112.10/500 Active

  FLOW IPSEC: allowed ip 192.168.0.0/255.255.255.0 192.168.110.0/255.255.255.0

  Active sAs: 2, origin: card crypto

  FLOW IPSEC: allowed 1 192.168.0.0/255.255.255.0 192.168.110.0/255.255.255.0

  Active sAs: 0, origin: card crypto

  FLOW IPSEC: allowed 6 192.168.0.0/255.255.255.0 192.168.110.0/255.255.255.0

  Active sAs: 0, origin: card crypto

  FLOW IPSEC: allowed ip host 122.3.112.10 192.168.0.0/255.255.255.0

  Active sAs: 0, origin: card crypto

  Crypto ACL 102, should really include only 1 line, that is to say:

  10 permit ip 192.168.0.0 0.0.0.255 192.168.110.0 0.0.0.255

  and you should have the image mirror on the remote end ACL line too.

  PLS, remove the remaining lines on 102 ACL ACL.

  I guess that the ACL 101 is NAT exemption, if it is pls include "deny ip 192.168.0.0 0.0.0.255 192.168.110.0 0.0.0.255" on top of your current line "license".

  Clear the tunnels as well as the NAT translation table after the changes described above.

• Controller of domain and DNS behind RRAS without VPN connected directly to the internet with a Cisco router

  I hava a ME Cisco 3400 with physical single port available for a cable connection.

  The ISP give me an IP address interface = 89.120.29.89 to act as a gateway to the IP Address of the host, which is provided for in the order 89.120.29.90.

  The host computer is a dual Xeon computer with two NICs for LAN and WAN.

  Fields of application: to install a windows 2008 R2 between public and private network server.

  Even though I know it's not recomanded, I put the DNS role and directories Active Directory roles installed on the same computer, the computer above, (I do not have enough computer for roles different place on different computers)

  The desired configuration:

  To have installed with his roles behind a WS2008R2 has RRAS. without a VPN.

  b with VPN

  and for WAN access for the client computers of the private LAN Windows 7 OS. (The basin of LAN address 192.168.0.1 - 255).

  First step : to have internet access in the browser (I use Google chrome) (without taking into account the DNS and AD)

  Network configuration:

  Map NETWORK WAN, at the top of the stack of liaison in the Control Panel/network connections and sharing:

  Host IP: 89.120.29.90

  Mask: 255.255.255.252

  Gateway: 89.120.29.89

  DNS: 193.231.100.130 my ISP name server address.

  OK, I can browse the internet.

  Second stage. (Consider DNS and Active Directories)

  DNS instaled role for this computer.

  AD installed as a global catalog.

  NETWORK WAN server that is directly connected to the Cisco router:

  Conection area 3

  Properties:

  Client for Microsoft Netwaork: not verified

  Network Load Balancing: not verified

  File and shared printer: not verified

  QoSPacketScheduler: not verified;

  Microsoft Network Monitor 3 pilot: not verified

  IPv4                                                     ;  checked

  Pilot a Link Layer Topology Mapper i/o: checked

  Link layer Discover responder: checked

  IPv4 tab

  Host IP: 89.120.29.90

  Mask: 255.255.255.252

  Gateway: 89.120.29.89

  DNS: 193.231.100.130 my ISP name server address.

  under the tab advanced

  IP settings : even that, tab IPV4 with automatic metric check;

  DNS tab :

  Add primary and connection suffixes DNS specific: not verified

  Add suffixes primary DNS suffixes parents: not verified

  Add this DNS suffixes: no

  Registry deals with this connection in DNS: not verified;

  Use this connection DNS suffix in DNS registration: not verified;

  WINS tab : enable search LMHOST: not verified

  Enable NetBios over TCP IP: don't check;

  Disable NetBios on TCP IP: checked;

  Connection to the local network 2

  Properties :

  Client for Microsoft Netwaork: checked

  Network Load Balancing: no

  File and shared printer: checked

  QoS Packet Scheduler: not verified;

  Microsoft Network Monitor 3 pilot: not verified

  IPv4 checked

  Pilot a Link Layer Topology Mapper i/o: checked

  Link layer Discover responder: checked

  IPv4 tab

  NETWORK LAN CARD: 192.168.0.101

  Mask: 255.255.255.0

  Gateway: 192.168.0.1

  under Advanced tab:

  IP settings : even that, tab IPV4 with automatic metric check;

  DNS tab :

  Add primary and connection suffixes DNS specific: checked

  Add suffixes primary DNS suffixes parents: not verified

  Add this DNS suffixes: no

  Registry deals with this connection in DNS: checked;

  Use this connection DNS suffix in DNS registration: checked;

  WINS tab : enable search LMHOST: not verified

  Enable NetBios over TCP IP: check;

  Disable NetBios on TCP IP: not verified;

  Install RRAS as NAT (NAT) under any condition imposed by DHCP(not installed) in ideea that RRAS will generate the private IP address of the DHCP allocator.

  In any case, for the beginning, I have a fix IP, do not get IP automatically.

  At this point, it gets the configuration simple posible for RRAS follows:

  3, LAN connection that corespond to the WAN interface IP:

  "NAT configured for the following Internet interface: Local Area Connection 3.
  The clients on the local network will assign the IP addresses of the following range:

  network address: 192.168.0.0. netmask 255.255.0.0.

  After Windows RRAS are open:

  The Network Interfaces tab:

  NICs are enabled and connected;

  UAL remotely & policies:

  Launch NPS,

  on the NPS server tab:

  Allow access to successful Active Directory directories:

  Properties: authentication: port 1812,1645

  kept port 1813,1646;

  on the accounting tab: nothing;

  under NPS policies:

  Grant permission for the RRAS server under builin\Administrator of the accounts;

  On strategy and the type of server unspecified (NAT do not exist as an entry in the drop-down list server dwn)

  under the static road: nothing;

  under the IPv4 tab or both are there(there IP) and are up

  under NAT

  Connection to the local network 3: public interface connected to the internet

  enable NAT on this interface:

  under the address pool: ISP addresses public;(two addresses)

  under the terms of service and the ports: Web server: http 80.

  (I have I have a static IP address for the client computer in mind, I set up a single customer).

  At the client computer :

  configured as domain customer and added to the users AD and computer AD

  logon to the domain:

  Local Area Connection

  Properties:

  Client for Microsoft Netwaork: checked

  Network Load Balancing: not verified

  File sharing and printer: checked

  QoS Packet Scheduler: checked;

  Microsoft Network Monitor 3 pilot: not verified

  IPv4                                                     ;  checked

  Pilot a Link Layer Topology Mapper i/o: checked

  Link layer Discover responder: checked

  IPv4 tab

  Host IP: 192.168.0.101

  Mask: 255.255.0.0

  Gateway: 192.168.0.1

  DNS: (auto-add the same to the local machine).

  under the tab advanced

  IP settings : even that, tab IPV4 with automatic metric check;

  DNS tab :

  Add primary and connection suffixes DNS specific: checked

  Add suffixes primary DNS suffixes parents: not verified

  Add this DNS suffixes: no

  Registry deals with this connection in DNS: checked;

  Use this connection DNS suffix in DNS registration: checked;

  WINS tab : enable search LMHOST: not verified

  Enable NetBios over TCP IP: checked;

  Disable NetBios on TCP IP: not verified;

  right now the 192.168.0.101 client cannot connect to internet through RRAS.

  ;

  This issue is beyond the scope of this site and must be placed on Technet or MSDN

  http://social.technet.Microsoft.com/forums/en-us/home

  http://social.msdn.Microsoft.com/forums/en-us/home

• I'd like to find the password for my Cisco router

  I can't connect to my network wirelessly on my ereader, because I don't know what is the password when asked.

  Read the manual for the device (Cisco router) should tell you what the password by default is to manage the router (if this does not work... it should tell you how to configure the default router, so you can use the default password to reconfigure) so you can go and change the password to access wireless to something You know.

• Cisco router linksys e1000 wireless

  a friend of my sister bought a cisco router (see the above subject line). Unfortunately, I was not home at the same time. Currently, there are a desktop wired to the router and a laptop with a Wi - Fi connection. The person who set up the router I forgot the username and the password of the router (didn't even bother to write this info). I convey my computer laptop home from work where I had a connection to internet/router. My laptop (Dell classroom business), I can see the two connections without wire (secured and unsecured comments). When I try to connect to the secure connection I do not get any screen of security, connection, etc., guests. He said something like 'try to check the security info' - do not remember the exact verbage. Anyway, I can not connect. The signal strength is strong - the bars are green. Can connect to the connection of comments, I am not always invited for any connection and safety info. Run the ipconfig/all command confirms the connection. I have still no internet access. Don't know why, but the signal strength readings 'poor' - a single green bar (while the secure connection shows all the force green signal bars). I have installed / configured several wireless - never had a problem.  I need to recover the connection info router without having to perform a hard reset on the router (I have same access limitted in my house of sisters/partners where the router). Is there a way to do it. I spoke twice to the cisco technical support and received two different answers (not according to the first call, open Explorer, go to programs/cisco for the info). This must be done on the computer that was used to install the cisco installation disc). Help, please!

  There are a lot of things I want to share with you on your router E1000 installation:

  1 E1000 comes with an installation CD that has CIsco Connect (the icon looks like a house) to easily manage your wireless network (you can easily get your password for the Cisco connection). Cisco Connect (CCC) is generally accessible to the computer that is first used to install the router (maybe this is why the tech officer ask you to go to the computer used to install this)

  2 E1000 broadcasts 2 signals of the main network and - network of comments. Once you click on the name of the network, you can easily connect the guest network seems to be unsecured However, when you access a Web site you will be asked a password. Always secure line.

  3. you can actually access to internet but not wireless cable but to the router.

  4. If you don't have the computer used to install the router, you must reconfigure and the first thing to do is to reset the router. You must configure manually if you do not have the installation cd.

  You can try these links:

  Setting up a Linksys router for DSL Internet connection

  Setting up a router with cable Internet Service