Cisco SG300 / ASA 5505 intervlan routing problem
Dear all
I have a problem with the configuration correctly sg300 layer 3 behind the ASA 5505 switch (incl. license more security)
The configuration is the following:
CISCO SG300 is configured as a layer 3 switch
VLAN native 1: 192.168.1.254, default route ip address (inside interface ASA 192.168.1.1)
VLAN defined additional switch
VLAN 100 with 192.168.100.0/24, default gateway 192.168.100.254
VLAN 110 with 192.168.110.0/24, default gateway 192.168.110.254
VLAN 120 with 172.16.0.0/16, default gateway 172.16.10.254
Of the VLANS (100,110,120) different, I am able to connect to all devices on the other VIRTUAL local networks (with the exception of Native VLAN 1; is not the ping requests)
From the switch cli I can ping my firewall (192.168.1.1) and all the other gateways of VLANs and vlan (VLAN1, 100, 110, 120) devices
Asa cli I can only ping my switch (192.168.1.254) port, but no other devices in other VLAN
My question is this. What should I change or installation in the switch configuration or asa so that other VLANs to access the Internet through the ASA. I will not use the ASA as intervlan routing device, because the switch does this for me
I tried to change the asa int e0/1 in trunkport (uplink port switch also), to enable all the VLANS, but as soon as I do that, I can not ping 192.168.1.254 ASA cli more.
Any help is greatly appreciated
Concerning
Edwin
Hi Edwin, because the switch is layer 3, the only necessary behavior is to ensure that default gateways to the computer are set on the SVI interface connection to the switch to make sure that the switch is transfer traffic wished to the ASA.
The configuration between the ASA and the switch must stay true by dot1q, such as the vlan all other, unidentified native VLAN tagged.
Also, if I'm not wrong, on the SAA you must set the security level of the port to 100.
-Tom
Please evaluate the useful messages
Tags: Cisco Support
Similar Questions
-
Hi all
First of all, I apologize if this is something that I can google. My knowledge of the administration of the network is all self-taught, so if there is a guide that I missed please point me in the right direction, it is often difficult to Google the terms for troubleshooting when your jargon is not the height.
The main problem is that when ping devices internal when you are connected to the results are very inconsistent.
Ping 192.168.15.102 with 32 bytes of data:
Reply from 192.168.15.102: bytes = 32 time = 112ms TTL = 128
Request timed out.
Request timed out.
Request timed out.
We have implemented an IPSec VPN connection to a remote Cisco ASA 5505. There is no connection problems, connection seems constant, etc. good packages. At this stage, I can only assume I have configuration problems, but I was watching this while if long and pair with my inexperience configuration of these settings I have no idea where to start. My first impressions are that LAN devices I'm ping do not send their response back or the ASA does not know how to route packets back?
Here is a dump of the configuration:
Output of the command: "show config".
: Saved
: Written by enable_15 to the 12:40:06.114 CDT MON Sep 9 2013
!
ASA Version 8.2 (5)
!
hostname VPN_Test
activate the encrypted password of D37rIydCZ/bnf1uj
2KFQnbNIdI.2KYOU encrypted passwd
names of
192.168.15.0 - internal network name
DDNS update method DDNS_Update
DDNS both
maximum interval 0 4 0 0
!
!
interface Ethernet0/0
switchport access vlan 2
!
interface Ethernet0/1
!
interface Ethernet0/2
!
interface Ethernet0/3
!
interface Ethernet0/4
!
interface Ethernet0/5
!
interface Ethernet0/6
!
interface Ethernet0/7
!
interface Vlan1
Description VLAN internal guests
nameif inside
security-level 100
DDNS update hostname 0.0.0.0
DDNS update DDNS_Update
DHCP client updated dns server time
192.168.15.1 IP address 255.255.255.0
!
interface Vlan2
Description of VLAN external to the internet
nameif outside
security-level 0
address IP xx.xx.xx.xx 255.255.255.248
!
passive FTP mode
clock timezone CST - 6
clock to summer time recurring CDT
DNS server-group DefaultDNS
Server name 216.221.96.37
Name-Server 8.8.8.8
permit same-security-traffic inter-interface
permit same-security-traffic intra-interface
DM_INLINE_TCP_1 tcp service object-group
port-object eq www
EQ object of the https port
outside_access_in list extended access permit icmp any one
outside_access_in list extended access deny interface icmp outside interface inside
access extensive list ip 192.168.15.192 outside_access_in allow 255.255.255.192 all
Remote_splitTunnelAcl list standard allowed internal-network access 255.255.255.0
inside_nat0_outbound list extended access allowed internal-network ip, 255.255.255.0 192.168.15.192 255.255.255.192
Note to inside_access_in to access list blocking Internet traffic
access extensive list ip 192.168.15.192 inside_access_in allow 255.255.255.192 all
Note to inside_access_in to access list blocking Internet traffic
inside_access_in extended access list allow interface ip inside the interface inside
inside_access_in list of allowed ip extended access all 192.168.15.192 255.255.255.192
Note to inside_access_in to access list blocking Internet traffic
access extensive list ip 192.168.15.192 inside_nat0_outbound_1 allow 255.255.255.192 all
pager lines 24
Enable logging
asdm of logging of information
Within 1500 MTU
Outside 1500 MTU
mask 192.168.15.200 - 192.168.15.250 255.255.255.0 IP local pool VPN_IP_Pool
inside_access_ipv6_in list of access allowed IPv6 interface ip inside the interface inside
ICMP unreachable rate-limit 1 burst-size 1
ICMP allow any inside
ICMP allow any response of echo outdoors
ICMP allow all outside
don't allow no asdm history
ARP timeout 14400
NAT-control
Global 1 interface (outside)
NAT (inside) 0-list of access inside_nat0_outbound
NAT (inside) 0 inside_nat0_outbound_1 list of outdoor access
NAT (inside) 1 192.168.15.192 255.255.255.192
NAT (inside) 1 0.0.0.0 0.0.0.0
inside_access_in access to the interface inside group
inside_access_ipv6_in access to the interface inside group
Access-group outside_access_in in interface outside
Route outside 0.0.0.0 0.0.0.0 xx.xx.xx.xx 1
Timeout xlate 03:00
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
Floating conn timeout 0:00:00
dynamic-access-policy-registration DfltAccessPolicy
Enable http server
http 192.168.1.0 255.255.255.0 inside
255.255.255.0 inside internal network http
http yy.yy.yy.yy 255.255.255.255 outside
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown cold start
Sysopt connection timewait
Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
Crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac
Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac
Crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac
Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac
Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac
Crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
Crypto ipsec transform-set ESP-AES-128-MD5-esp - aes esp-md5-hmac
life crypto ipsec security association seconds 28800
Crypto ipsec kilobytes of life - safety 4608000 association
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 pfs Group1 set
Crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 value transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5
outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP
outside_map interface card crypto outside
crypto ISAKMP allow outside
crypto ISAKMP policy 10
preshared authentication
3des encryption
sha hash
Group 2
life 86400
Telnet timeout 5
SSH timeout 5
Console timeout 0
management-access inside
dhcpd outside auto_config
!
dhcpd address 192.168.15.200 - 192.168.15.250 inside
dhcpd allow inside
!
a basic threat threat detection
Statistics-list of access threat detection
a statistical threat detection tcp-interception rate-interval 30 burst-400-rate average rate 200
NTP server 192.168.15.101 source inside
prefer NTP server 192.168.15.100 source inside
WebVPN
internal remote group strategy
Group remote attributes policy
Protocol-tunnel-VPN IPSec
Split-tunnel-policy tunnelspecified
value of Split-tunnel-network-list Remote_splitTunnelAcl
username StockUser encrypted password privilege 0 t6a0Nv8HUfWtUdKz
username StockUser attributes
Strategy-Group-VPN remote
tunnel-group type remote access remotely
tunnel-group remote General attributes
address pool VPN_IP_Pool
Group Policy - by default-remote control
tunnel-group remote ipsec-attributes
pre-shared-key *.
!
class-map inspection_default
match default-inspection-traffic
!
!
type of policy-card inspect dns preset_dns_map
parameters
maximum message length automatic of customer
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the preset_dns_map dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
inspect the rsh
inspect the rtsp
inspect esmtp
inspect sqlnet
inspect the skinny
inspect sunrpc
inspect xdmcp
inspect the sip
inspect the netbios
inspect the tftp
Review the ip options
inspect the icmp
!
global service-policy global_policy
context of prompt hostname
no remote anonymous reporting call
Cryptochecksum:f4271785b86e45dd3a17bab8f60cd2f3
Hi Graham,
My first question is do you have a site to site VPN and VPN remote access client.
After checking your configuration, I see you don't have any Site to SIte VPN configuration, so I'm assuming you ara facing issue with the VPN client.
And if I understand you are able to connect VPN client, but you not able to access internal resources properly.
I recommend tey and make the following changes.
First remove the following configuration:
NAT (inside) 0 inside_nat0_outbound_1 list of outdoor access
NAT (inside) 1 192.168.15.192 255.255.255.192
You don't need the 1st one and I do not understand the reason for the second
Second, one is your pool IP subnet (192.168.15.200 - 192.168.15.250) and I don't know why you added this NAT.
If possible change your subnet pool all together because we do not recommend to use th ip POOL that is similar to your local network.
Try the changes described above and let me know in case if you have any problem.
Thank you
Jeet Kumar
-
ASA 5505 in router Mode can implement the MAC ACL
Hi all:
My client request can the Cisco ASA 5505 implement MAC ACL in Cisco ASA 5505, who is now running in router Mode.
Can anyone help answer this?
I tried to search the document and also tried the ASDM in the Cisco ASA 5505 but couldn't see a way to do the ACL by MAC address.
At the same time can also help me find the command line using the ASA 5505 able to run MAC ACL in router mode?
Thank you very much!
Warm greetings,
TangSuan Tan
MAC ACL is not supported in Routed mode, only in Transparent mode.
Here is the command for your reference:
http://www.Cisco.com/en/us/docs/security/ASA/asa84/command/reference/A1.html#wp1598101
And here is the ethertype supported:
http://www.Cisco.com/en/us/docs/security/ASA/asa84/configuration/guide/access_rules.html#wp1083699
-
Hi friends,
I have a question related to the Inter-VLAN routing. I have 2 switch a 3850 L3 and another is 2960 L2 (Pure L2). I even vlan on both switches and IP routing enabled on switch L3. But not woking switch l3 to L2 Intervlan Routing switching systems.
Configuration as below:
L3 switch:
hostname L3
!
IP routing
!
pvst spanning-tree mode
!
interface FastEthernet0/1
switchport access vlan 7
spanning tree portfast
!
interface FastEthernet0/2
!
interface FastEthernet0/3
!
interface FastEthernet0/4
!
interface FastEthernet0/5
!
interface FastEthernet0/6
!
interface FastEthernet0/7
!
interface FastEthernet0/8
!
interface FastEthernet0/9
!
interface FastEthernet0/10
!
interface FastEthernet0/11
!
interface FastEthernet0/12
!
interface FastEthernet0/13
!
interface FastEthernet0/14
!
interface FastEthernet0/15
!
interface FastEthernet0/16
!
interface FastEthernet0/17
!
interface FastEthernet0/18
!
interface FastEthernet0/19
!
interface FastEthernet0/20
!
interface FastEthernet0/21
!
interface FastEthernet0/22
!
interface FastEthernet0/23
!
interface FastEthernet0/24
Are connected to the L2 switch
switchport trunk encapsulation dot1q
switchport mode trunk
!
interface GigabitEthernet0/1
!
interface GigabitEthernet0/2
!
interface Vlan1
no ip address
Shutdown
!
interface Vlan2
IP 1.1.1.1 255.255.255.0
!
interface Vlan3
3.3.3.3 IP address 255.255.255.0
!
interface Vlan4
4.4.4.4 IP address 255.255.255.0
!
interface Vlan5
5.5.5.5 IP address 255.255.255.0
!
interface Vlan6
6.6.6.6 IP address 255.255.255.0
!
interface Vlan7
7.7.7.7 IP address 255.255.255.0
!
interface Vlan8
8.8.8.8 IP address 255.255.255.0
!
interface Vlan9
9.9.9.9 IP address 255.255.255.0
!
IP classless
-----------------
The L2 switch configuration:
!
hostname SwitchL2
!
!
!
!
!
pvst spanning-tree mode
!
interface FastEthernet0/1
switchport access vlan 2
!
interface FastEthernet0/2
!
interface FastEthernet0/3
!
interface FastEthernet0/4
!
interface FastEthernet0/5
!
interface FastEthernet0/6
!
interface FastEthernet0/7
!
interface FastEthernet0/8
!
interface FastEthernet0/9
!
interface FastEthernet0/10
!
interface FastEthernet0/11
!
interface FastEthernet0/12
!
interface FastEthernet0/13
!
interface FastEthernet0/14
!
interface FastEthernet0/15
!
interface FastEthernet0/16
!
interface FastEthernet0/17
!
interface FastEthernet0/18
!
interface FastEthernet0/19
!
interface FastEthernet0/20
!
interface FastEthernet0/21
!
interface FastEthernet0/22
!
interface FastEthernet0/23
!
interface FastEthernet0/24
switchport mode trunk
switchport nonegotiate
!
interface GigabitEthernet0/1
!
interface GigabitEthernet0/2
!
interface Vlan1
no ip address
Shutdown
!
interface Vlan2
1.1.1.2 IP 255.255.255.0
!
interface Vlan7
IP 7.7.7.8 255.255.255.0
!-------------------
Note: I do not have any router.
When I test the same setting on packet tracer then get error:
1. the destination IP address is not the broadcast address, and it does not match the IP address of the port. The appliance ignores the packet.
Please resolev question:
Kind regards.
Deepak Kumar
I think that Reza questions 3 and 4 are more important than questions 1 and 2, but perhaps do not go quite far enough. The two switches to assign certain ports to a vlan specific and use the vlan by default for most of the ports. There are no statements on a switch which create the vlan but only statements that a port must Access a specified VLAN
interface FastEthernet0/1
switchport access vlan 7
On some versions of switches that may be enough to create the vlan, but on other switches, it is necessary to create the vlan before using it. Maybe something like
VLAN 7
name server_vlan
I would ask if the VLAN on each switch existence?
There is another question in this config. The switches have created more than 3 VLANs (vlan 1 - the vlan by default and vlan 2 and vlan 7.) But the L3 switch configured more than one interface vlan (3, 4, 5, 6, 8, 9). Without a vlan underlying pertaining to these layer 3 interfaces vlan will not work.
HTH
Rick
-
SG300-28 questions - InterVLAN routing
Hi all
I am trying to switch SG300-28 place and do work for several days, with a very simple configuration, but this device is just to stuborn giving me headaches. I hope that you will tell me a solution to my problem.
So I configured the VLAN on the switch, assigned to all ports, given IP addresses for VLANs, etc.. But I digress not test phase where I try to rattle of two stations of different VLANS.
I have pictures of the attached current configuration. Stations are on ports 4 (VLAN4) and port 15 (VLAN3). First good 192.168.30.x a station address with the default gateway 192.168.30.1. Second station address of the 192.168.5.x and gateway 192.168.5.1. The two stations can ping the two gateways, but not eachother. Traffic within a VIRTUAL local network works fine, so routing is the most obvious problem.
There is no active ACLs.
Please see attached photos and give me something to try, because I spent three days to experiment without luck!
One of the biggest mistakes I see relies on 'ping' to see if things work. Do not forget that the 'ping' sends a request to echo, that does not force the customer to send and echo response. Ensure that stations are configured to respond to pings or try to access a share, or a service configured on clients. Another thing to consider, that the client ports access ports and not General, this can be a problem, but it should be allowed, as is.
On a side note, the current configuration you cannot access anything out in the cloud. If you need to access cloud do not forget to add a default route on the switch.
I hope this helps!
-
Cannot find the next jump - ASA 5505 VPN routing l2l
We have a 5505 (soon to be replaced by two 5515-x) firewall with two VPN l2l.
"Were trying to allow a remote site traffic flow through the other remote site but the syslog shows."
10.5.25.4 1 172.16.10.10 0 Could not locate the next hop for ICMP outside:10.5.25.4/1 to inside:172.16.10.10/0 routing
Config is less than
:
ASA Version 8.4 (3)
names of
!
interface Ethernet0/0
switchport access vlan 2
Speed 100
full duplex
!
interface Ethernet0/1
!
interface Ethernet0/2
!
interface Ethernet0/3
!
interface Ethernet0/4
!
interface Ethernet0/5
!
interface Ethernet0/6
<--- more="" ---="">
!
interface Ethernet0/7
switchport access vlan 10
!
interface Vlan1
nameif inside
security-level 100
allow-ssc-mgmt
IP 10.5.19.254 255.255.255.0
!
interface Vlan2
WIMAX Interface Description
nameif outside
security-level 0
IP address x.247.x.18 255.255.255.248
!
passive FTP mode
clock timezone GMT 1
permit same-security-traffic inter-interface
permit same-security-traffic intra-interface
network obj_any object
subnet 0.0.0.0 0.0.0.0
network guestwifi object
10.1.110.0 subnet 255.255.255.0
<--- more="" ---="">
network of the NETWORK_OBJ_10.5.19.0_24 object
10.5.19.0 subnet 255.255.255.0
network of the NETWORK_OBJ_10.5.31.0_24 object
10.5.31.0 subnet 255.255.255.0
network of the NETWORK_OBJ_172.16.0.0_16 object
subnet 172.16.0.0 255.255.0.0
the object DS365-Cloud network
172.16.10.0 subnet 255.255.255.0
Description DS365-Cloud
network of the object to the inside-network-16
10.5.0.0 subnet 255.255.0.0
atanta network object
10.5.16.0 subnet 255.255.255.0
Atanta description
network guest_dyn_nat object
10.5.29.0 subnet 255.255.255.0
network of the NETWORK_OBJ_172.16.254.0_25 object
subnet 172.16.254.0 255.255.255.128
network of the NETWORK_OBJ_10.5.16.0_20 object
subnet 10.5.16.0 255.255.240.0
network of the NETWORK_OBJ_10.5.16.0_26 object
255.255.255.192 subnet 10.5.16.0
network of the LDAP_DC7 object
Home 10.5.21.1
<--- more="" ---="">
LDAP description
network c2si object
range 10.5.21.180 10.5.21.200
network of the NETWORK_OBJ_10.5.25.0_24 object
10.5.25.0 subnet 255.255.255.0
object-group network rfc1918
object-network 192.168.0.0 255.255.0.0
object-network 172.16.0.0 255.255.240.0
object-network 10.0.0.0 255.0.0.0
the DM_INLINE_NETWORK_1 object-group network
object-network 10.5.19.0 255.255.255.0
network-object 10.5.20.0 255.255.254.0
object-network 10.5.22.0 255.255.255.0
object-network 10.5.30.0 255.255.255.0
object-network 192.168.100.0 255.255.255.0
the Sure_Signal object-group network
network-object x.183.x.128 255.255.255.192
network-host x.183.133.177 object
network-host x.183.133.178 object
network-host x.183.133.179 object
network-host x.183.133.181 object
network-host x.183.133.182 object
the LDAP_source_networks object-group network
network-object 135.196.24.192 255.255.255.240
<--- more="" ---="">
object-network 195.130.x.0 255.255.255.0
network-object x.2.3.128 255.255.255.192
network-object 213.235.63.64 255.255.255.192
object-network 91.220.42.0 255.255.255.0
object-network 94.x.240.0 255.255.255.0
object-network 94.x.x.0 255.255.255.0
the c2si_Allow object-group network
host of the object-Network 10.5.16.1
host of the object-Network 10.5.21.1
network-object object c2si
the DM_INLINE_NETWORK_2 object-group network
network-object 10.5.20.0 255.255.254.0
object-network 10.5.21.0 255.255.255.0
object-network 10.5.22.0 255.255.255.0
object-network 10.5.29.0 255.255.255.0
network-object, object NETWORK_OBJ_10.5.19.0_24
the DM_INLINE_NETWORK_3 object-group network
object-network 10.5.19.0 255.255.255.0
network-object 10.5.20.0 255.255.254.0
object-network 10.5.21.0 255.255.255.0
object-network 10.5.22.0 255.255.255.0
atanta network-object
the DM_INLINE_NETWORK_4 object-group network
network-object 10.5.20.0 255.255.254.0
<--- more="" ---="">
object-network 10.5.21.0 255.255.255.0
object-network 10.5.22.0 255.255.255.0
object-network 10.5.23.0 255.255.255.0
object-network 10.5.30.0 255.255.255.0
network-object, object NETWORK_OBJ_10.5.19.0_24
atanta network-object
network-object DS365-Cloud
inside_access_in list extended access permit tcp any eq 50 Sure_Signal object-group
inside_access_in list extended access permit tcp any object-group Sure_Signal eq pptp
inside_access_in list extended access permits will all object-group Sure_Signal
inside_access_in list extended access permit udp any eq ntp Sure_Signal object-group
inside_access_in access list extended icmp permitted no echo of Sure_Signal object-group
inside_access_in list extended access permit udp any eq 50 Sure_Signal object-group
inside_access_in list extended access permit udp any eq Sure_Signal object-group 4500
inside_access_in list extended access permit udp any eq isakmp Sure_Signal object-group
inside_access_in of access allowed any ip an extended list
255.255.0.0 allow access list extended ip 10.5.0.0 clientvpn 10.5.30.0 255.255.255.0
access-list extended BerkeleyAdmin-clientvpn ip 10.5.0.0 allow 255.255.0.0 10.5.30.0 255.255.255.0
IP 10.5.21.0 allow to Access-list BerkeleyUser-clientvpn extended 255.255.255.0 10.5.30.0 255.255.255.0
outside_cryptomap extended access list permit ip object inside-network-16 10.5.25.0 255.255.255.0
access extensive list ip 10.5.29.0 guest_access_in allow 255.255.255.0 any
state_bypass allowed extended access list tcp 192.168.100.0 255.255.255.0 10.5.30.0 255.255.255.0 connect
state_bypass allowed extended access list tcp 10.5.30.0 255.255.255.0 192.168.100.0 255.255.255.0 connect
state_bypass allowed extended access list tcp 10.5.29.0 255.255.255.0 10.5.30.0 255.255.255.0 connect
<--- more="" ---="">
state_bypass allowed extended access list tcp 10.5.30.0 255.255.255.0 10.5.29.0 255.255.255.0 connect
outside_access_in list extended access permit icmp any one
access extensive list ip 10.5.16.0 outside_cryptomap_1 allow 255.255.240.0 10.5.16.0 255.255.255.192
access-list extended global_access permitted tcp object-group LDAP_source_networks host 10.5.21.1 eq ldap
access extensive list 10.5.0.0 ip outside_cryptomap_2 255.255.0.0 allow object DS365-Cloud
outside_cryptomap_3 list extended access allowed object-group ip DM_INLINE_NETWORK_4 10.5.25.0 255.255.255.0
pager lines 24
Enable logging
exploitation forest-size of the buffer of 100000
recording of debug console
debug logging in buffered memory
asdm of logging of information
Within 1500 MTU
Outside 1500 MTU
IP local pool clientvpn 10.5.30.1 - 10.5.30.100
mask 172.16.254.1 - 172.16.254.100 255.255.255.0 IP local pool VPN_IP_Pool
no failover
ICMP unreachable rate-limit 1 burst-size 1
ICMP allow any inside
ICMP allow all outside
don't allow no asdm history
ARP timeout 14400
NAT (inside, outside) source static rfc1918 rfc1918 destination rfc1918 static rfc1918
NAT (inside, outside) static source NETWORK_OBJ_10.5.19.0_24 NETWORK_OBJ_10.5.19.0_24 NETWORK_OBJ_10.5.31.0_24 NETWORK_OBJ_10.5.31.0_24 non-proxy-arp-search of route static destination
<--- more="" ---="">
NAT (inside, outside) static source NETWORK_OBJ_10.5.19.0_24 NETWORK_OBJ_10.5.19.0_24 NETWORK_OBJ_10.5.19.0_24 NETWORK_OBJ_10.5.19.0_24 non-proxy-arp-search of route static destination
NAT (inside, outside) static source to the static inside-network-16 inside-network-16 destination DS365-DS365-cloud no-proxy-arp-route search
NAT (inside, outside) static source DM_INLINE_NETWORK_1 DM_INLINE_NETWORK_1 NETWORK_OBJ_172.16.254.0_25 NETWORK_OBJ_172.16.254.0_25 non-proxy-arp-search of route static destination
NAT (inside, outside) static source NETWORK_OBJ_10.5.16.0_20 NETWORK_OBJ_10.5.16.0_20 NETWORK_OBJ_10.5.16.0_26 NETWORK_OBJ_10.5.16.0_26 non-proxy-arp-search of route static destination
NAT (inside, outside) source static c2si_Allow c2si_Allow NETWORK_OBJ_172.16.254.0_25 NETWORK_OBJ_172.16.254.0_25 non-proxy-arp-search of route static destination
NAT (inside, outside) source static atanta atanta static destination NETWORK_OBJ_10.5.25.0_24 NETWORK_OBJ_10.5.25.0_24 non-proxy-arp-search to itinerary
NAT (inside, outside) static source DS365-DS365-cloud static destination NETWORK_OBJ_10.5.25.0_24 NETWORK_OBJ_10.5.25.0_24 non-proxy-arp-search to itinerary
NAT (inside, outside) static source DM_INLINE_NETWORK_2 DM_INLINE_NETWORK_2 NETWORK_OBJ_10.5.25.0_24 NETWORK_OBJ_10.5.25.0_24 non-proxy-arp-search of route static destination
NAT (inside, outside) static source NETWORK_OBJ_10.5.25.0_24 NETWORK_OBJ_10.5.25.0_24 static destination DS365-DS365-cloud no-proxy-arp-route search
NAT (inside, outside) static source DM_INLINE_NETWORK_3 DM_INLINE_NETWORK_3 static destination DS365-DS365-cloud no-proxy-arp-route search
NAT (inside, outside) static source to the inside-network-16 inside-network-16 destination static NETWORK_OBJ_10.5.25.0_24 NETWORK_OBJ_10.5.25.0_24 non-proxy-arp-search to itinerary
NAT (inside, outside) static source DM_INLINE_NETWORK_4 DM_INLINE_NETWORK_4 NETWORK_OBJ_10.5.25.0_24 NETWORK_OBJ_10.5.25.0_24 non-proxy-arp-search of route static destination
!
network obj_any object
NAT dynamic interface (indoor, outdoor)
network of the LDAP_DC7 object
NAT 194.247.x.19 static (inside, outside) tcp ldap ldap service
inside_access_in access to the interface inside group
Access-group outside_access_in in interface outside
Access-Group global global_access
!
Router eigrp 143
No Auto-resume
Network 10.5.19.0 255.255.255.0
<--- more="" ---="">
Network 10.5.29.0 255.255.255.0
Network 10.5.30.0 255.255.255.0
redistribute static
!
Route outside 0.0.0.0 0.0.0.0 194.247.x.17 1 track 1
Route inside 10.5.16.0 255.255.255.0 10.5.19.252 1
Timeout xlate 03:00
Pat-xlate timeout 0:00:30
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
Floating conn timeout 0:00:00
dynamic-access-policy-registration DfltAccessPolicy
RADIUS protocol for AAA-server group
AAA (inside) 10.5.21.1 host server group
key *.
AAA (inside) 10.5.16.1 host server group
key *.
identity of the user by default-domain LOCAL
the ssh LOCAL console AAA authentication
AAA authentication LOCAL telnet console
Enable http server
<--- more="" ---="">
http 192.168.1.0 255.255.255.0 inside
http 10.5.16.0 255.255.240.0 inside
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown warmstart of cold start
Sysopt connection tcpmss 1350
SLA 1 monitor
type echo protocol ipIcmpEcho 8.8.4.4 outside interface
SLA monitor Appendix 1 point of life to always start-time now
Crypto ipsec transform-set ikev1 strong-comp esp-aes-256 esp-sha-hmac
Crypto ipsec ikev1 transform-set strong aes-256-esp esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-128-SHA aes - esp esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-esp - aes esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
Crypto ipsec transform-set ikev1 SHA-ESP-3DES esp-3des esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-3DES-MD5-esp-3des esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-DES-SHA esp - esp-sha-hmac
Crypto ipsec transform-set ikev1 esp ESP-DES-MD5-esp-md5-hmac
Crypto ipsec ikev2 strong ipsec proposal
Protocol esp encryption aes-256
Esp integrity sha-1 protocol
<--- more="" ---="">
Crypto ipsec ikev2 AES256 ipsec-proposal
Protocol esp encryption aes-256
Esp integrity sha - 1, md5 Protocol
Crypto ipsec ikev2 ipsec-proposal AES192
Protocol esp encryption aes-192
Esp integrity sha - 1, md5 Protocol
Crypto ipsec ikev2 ipsec-proposal AES
Esp aes encryption protocol
Esp integrity sha - 1, md5 Protocol
Crypto ipsec ikev2 proposal ipsec 3DES
Esp 3des encryption protocol
Esp integrity sha - 1, md5 Protocol
Crypto ipsec ikev2 ipsec-proposal OF
encryption protocol esp
Esp integrity sha - 1, md5 Protocol
Crypto-map dynamic dyn1 1 set transform-set ikev1 strong
1 correspondence address outside_cryptomap_1 outside crypto map
crypto card outside pfs set 1
1 set 83.x.172.68 counterpart outside crypto map
Crypto card outside 1 set transform-set ESP-AES-256-SHA ikev1
1 set ikev2 AES256 ipsec-proposal outside crypto map
card crypto off game 2 address outside_cryptomap_3
map external crypto 2 peers set 23.100.x.177
card external crypto 2 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5
<--- more="" ---="">
map external crypto 2 set AES256 AES192 AES strong proposal ipsec ikev2
Crypto card outside 2 kilobytes of life of security association set 102400000
card crypto outside match 3 address outside_cryptomap_2
3 set pfs outside crypto map
map external crypto 3 peers set 91.x.3.39
crypto card outside ikev1 set 3 transform-set ESP-3DES-SHA
map external crypto 3 3DES ipsec-ikev2 set proposal
dynamic outdoor 100 dyn1 ipsec-isakmp crypto map
card crypto outside interface outside
Crypto ca trustpoint _SmartCallHome_ServerCA
Configure CRL
IKEv2 crypto policy 1
aes-256 encryption
integrity sha
Group 2
FRP sha
second life 86400
IKEv2 crypto policy 10
aes-192 encryption
integrity sha
Group 2 of 5
FRP sha
second life 86400
IKEv2 crypto policy 20
aes encryption
integrity sha
Group 2 of 5
FRP sha
second life 86400
IKEv2 crypto policy 30
3des encryption
integrity sha
Group 2 of 5
FRP sha
second life 86400
IKEv2 crypto policy 40
the Encryption
integrity sha
Group 2 of 5
FRP sha
second life 86400
Crypto ikev2 allow outside
Crypto ikev1 allow outside
IKEv1 crypto policy 1
preshared authentication
aes-256 encryption
sha hash
Group 2
lifetime 28800
IKEv1 crypto policy 2
preshared authentication
3des encryption
sha hash
Group 2
life 86400
!
track 1 rtr 1 accessibility
Telnet 10.5.16.0 255.255.240.0 inside
Telnet timeout 5
SSH 83.x.x.90 255.255.255.255 outside
SSH timeout 5
Console timeout 0
dhcpd outside auto_config
!
dhcprelay Server 10.5.21.1 on the inside
time-out of 60 dhcprelay
a basic threat threat detection
statistical threat detection port
<--- more="" ---="">
Statistical threat detection Protocol
Statistics-list of access threat detection
no statistical threat detection tcp-interception
NTP 10.5.19.253 Server prefer
WebVPN
allow outside
AnyConnect image disk0:/anyconnect-win-2.5.2014-k9.pkg 1
AnyConnect image disk0:/anyconnect-win-3.1.03103-k9.pkg 2
AnyConnect enable
tunnel-group-list activate
attributes of Group Policy DfltGrpPolicy
Ikev1 VPN-tunnel-Protocol l2tp ipsec without ssl-client
internal GroupPolicy_c2si group strategy
attributes of Group Policy GroupPolicy_c2si
WINS server no
value of 10.5.16.1 DNS server 10.5.21.1
client ssl-VPN-tunnel-Protocol
by default no
internal GroupPolicy_91.x.3.39 group strategy
attributes of Group Policy GroupPolicy_91.x.3.39
VPN-tunnel-Protocol ikev1, ikev2
internal GroupPolicy_83.x.172.68 group strategy
attributes of Group Policy GroupPolicy_83.x.172.68
VPN-tunnel-Protocol ikev1, ikev2
<--- more="" ---="">
internal GroupPolicy_23.100.x.177 group strategy
attributes of Group Policy GroupPolicy_23.100.x.177
VPN-tunnel-Protocol ikev1, ikev2
internal GroupPolicy_user group strategy
attributes of Group Policy GroupPolicy_user
WINS server no
value of 10.5.21.1 DNS server 10.5.16.1
client ssl-VPN-tunnel-Protocol
Split-tunnel-policy tunnelspecified
Split-tunnel-network-list value BerkeleyAdmin-clientvpn
myberkeley.local value by default-field
internal GroupPolicy_23.101.x.122 group strategy
attributes of Group Policy GroupPolicy_23.101.x.122
VPN-tunnel-Protocol ikev1, ikev2
internal GroupPolicy1 group strategy
attributes of Group Policy GroupPolicy1
VPN-tunnel-Protocol ikev1, ikev2
internal BerkeleyUser group strategy
attributes of Group Policy BerkeleyUser
value of 10.5.21.1 DNS server 10.5.16.1
Split-tunnel-policy tunnelspecified
Split-tunnel-network-list value BerkeleyUser-clientvpn
myberkeley.local value by default-field
internal DS365 group policy
<--- more="" ---="">
DS365 group policy attributes
VPN-idle-timeout no
VPN-filter no
IPv6-vpn-filter no
VPN-tunnel-Protocol ikev1, ikev2
internal BerkeleyAdmin group strategy
attributes of Group Policy BerkeleyAdmin
value of 10.5.21.1 DNS server 10.5.16.1
Split-tunnel-policy tunnelspecified
Split-tunnel-network-list value BerkeleyAdmin-clientvpn
myberkeley.local value by default-field
acsadmin encrypted V6hUzNl366K37eiV privilege 15 password username
atlanta uxelpvEvM3I7tw.Z encrypted privilege 15 password username
username of berkeley Kj.RBvUp5dtyLw5T encrypted password
type tunnel-group BerkeleyUser remote access
attributes global-tunnel-group BerkeleyUser
address clientvpn pool
authentication-server-group
Group Policy - by default-BerkeleyUser
IPSec-attributes tunnel-group BerkeleyUser
IKEv1 pre-shared-key *.
type tunnel-group BerkeleyAdmin remote access
attributes global-tunnel-group BerkeleyAdmin
address clientvpn pool
<--- more="" ---="">
authentication-server-group
Group Policy - by default-BerkeleyAdmin
IPSec-attributes tunnel-group BerkeleyAdmin
IKEv1 pre-shared-key *.
type tunnel-group user remote access
tunnel-group user General attributes
address pool VPN_IP_Pool
authentication-server-group
Group Policy - by default-GroupPolicy_user
tunnel-group user webvpn-attributes
enable-alias of user group
type tunnel-group c2si remote access
tunnel-group c2si-global attributes
address pool VPN_IP_Pool
authentication-server-group
Group Policy - by default-GroupPolicy_c2si
tunnel-group c2si webvpn-attributes
Group-alias c2si enable
tunnel-group 83.x.172.68 type ipsec-l2l
tunnel-group 83.x.172.68 General-attributes
Group - default policy - GroupPolicy_83.x.172.68
83.x.172.68 group of tunnel ipsec-attributes
IKEv1 pre-shared-key *.
remote control-IKEv2 pre-shared-key authentication *.
<--- more="" ---="">
pre-shared-key authentication local IKEv2 *.
tunnel-group 23.101.x.122 type ipsec-l2l
tunnel-group 23.101.x.122 General-attributes
Group - default policy - GroupPolicy_23.101.x.122
23.101.x.122 group of tunnel ipsec-attributes
IKEv1 pre-shared-key *.
remote control-IKEv2 pre-shared-key authentication *.
pre-shared-key authentication local IKEv2 *.
tunnel-group 91.x.3.39 type ipsec-l2l
tunnel-group 91.x.3.39 general-attributes
Group - default policy - GroupPolicy_91.x.3.39
91.x.3.39 group of tunnel ipsec-attributes
IKEv1 pre-shared-key *.
remote control-IKEv2 pre-shared-key authentication *.
pre-shared-key authentication local IKEv2 *.
tunnel-group 23.100.x.177 type ipsec-l2l
tunnel-group 23.100.x.177 General-attributes
Group - default policy - GroupPolicy_23.100.63.177
23.100.x.177 group of tunnel ipsec-attributes
IKEv1 pre-shared-key *.
remote control-IKEv2 pre-shared-key authentication *.
pre-shared-key authentication local IKEv2 *.
class-map state_bypass
corresponds to the state_bypass access list
Policy-map state_bypass_policy
class state_bypass
set the advanced options of the tcp-State-bypass connection
!
service-policy state_bypass_policy to the inside interface
context of prompt hostname
anonymous reporting remote call
Cryptochecksum:bbc6f2ec2db9b09a1b6eb90270ddfeea
: end
PTB-ch-asa5505 #.
Ah OK I see now.
Your cryptomap for the cloud of DS365 is:
access extensive list 10.5.0.0 ip outside_cryptomap_2 255.255.0.0 allow object DS365-Cloud
so, which covers interesting traffic.
However, your NAT statement is:
NAT (inside, outside) static source NETWORK_OBJ_10.5.25.0_24 NETWORK_OBJ_10.5.25.0_24 static destination DS365-DS365-cloud no-proxy-arp-route search
Network 10.5.25.0 is remote, then it will actually appear to be an "outside" network so I think you need this statement to begin "nat (outside, outside).
-
The SG300 - ACL support intervlan routing
I have Setup SG300 - 52p mode switch layer 3.
I have 3 VLAN (10,20,30) and the affected ports to each vlan.
Each host can ping its own gateway (according to the VLAN).
I want to enable some of the traffic of a vlan to a specific host (server) on a different VLAN. I try with ACL, but no can do.
Can someone help me how to do this?
Thank you very much.
Hey Ruy,
My isa very restrictive ACL.
Restrict_FTP extended IP access list
permit ip 192.168.10.0 0.0.0.255 192.168.20.10 0.0.0.0
output
It allows only the 192.168.10.0 network to get host 192.168.20.10 IP host.
There is also perhaps (in red);
Restrict_FTP extended IP access list
permit ip 192.168.10.0 0.0.0.255 192.168.20.10 0.0.0.0
deny ip 192.168.10.0 0.0.0.255 192.168.20.0 0.0.0.255
allow a full
output
I must confess that I prefer to use the GUI to produce my ACEs. The table he creates shows how the ACL will work. and especially in what order.
- The switch through ACEs in order from top to bottom as seen in the GUI.
- The ACL that is attached to an interface, boss of matching incoming packages (coming into the switch).
- ACE entries use reverse masking can be confusing. Perhaps the following tehnote may be useful for understanding the inverse of masking;
http://www.Cisco.com/en/us/products/sw/secursw/ps1018/products_tech_note09186a00800a5b9a.shtml
What about Dave
-
Problem with ASA 5505 VPN remote access
After about 1 year to have the VPN Client from Cisco connection to an ASA 5505 with no problems, all of a sudden one day it stops working. The customer is able to get a connection to the ASA and browse the local network for only about 30 seconds after the connection. After that, no access is available to the network behind the ASA. I have tried everything I can think of to try to solve the problem, but at this point, I'm just banging my head against a wall. Anyone know what could cause this?
Here is the cfg running of the ASA
----------------------------------------------------------------------------------------
: Saved
:
ASA Version 8.4 (1)
!
hostname NCHCO
enable encrypted password xxxxxxxxxxxxxxx
xxxxxxxxxxx encrypted passwd
names of
description of NCHCO name 192.168.2.0 City offices
name 192.168.2.80 VPN_End
name 192.168.2.70 VPN_Start
!
interface Vlan1
nameif inside
security-level 100
IP 192.168.2.1 255.255.255.0
!
interface Vlan2
nameif outside
security-level 0
IP address **. ***. 255.255.255.248
!
interface Ethernet0/0
switchport access vlan 2
Speed 100
full duplex
!
interface Ethernet0/1
!
interface Ethernet0/2
!
interface Ethernet0/3
!
interface Ethernet0/4
!
interface Ethernet0/5
!
interface Ethernet0/6
!
interface Ethernet0/7
!
boot system Disk0: / asa841 - k8.bin
passive FTP mode
network of the NCHCO object
Subnet 192.168.2.0 255.255.255.0
network object obj - 192.168.1.0
subnet 192.168.1.0 255.255.255.0
network object obj - 192.168.2.64
subnet 192.168.2.64 255.255.255.224
network object obj - 0.0.0.0
subnet 0.0.0.0 255.255.255.0
network obj_any object
subnet 0.0.0.0 0.0.0.0
the Web server object network
the FINX object network
Home 192.168.2.11
rdp service object
source between 1-65535 destination eq 3389 tcp service
Rdp description
outside_nat0_outbound extended access list permit ip object NCHCO 192.168.1.0 255.255.255.0
outside_nat0_outbound extended access list permit ip object NCHCO 192.168.2.0 255.255.255.0
inside_nat0_outbound extended access list permit ip object NCHCO 192.168.1.0 255.255.255.0
inside_nat0_outbound list of allowed ip extended access all 192.168.2.64 255.255.255.224
permit access list extended ip 0.0.0.0 inside_nat0_outbound 255.255.255.0 192.168.2.64 255.255.255.224
outside_1_cryptomap extended access list permit ip object NCHCO 192.168.1.0 255.255.255.0
outside_1_cryptomap_1 extended access list permit ip object NCHCO 192.168.1.0 255.255.255.0
LAN_Access list standard access allowed 192.168.2.0 255.255.255.0
LAN_Access list standard access allowed 0.0.0.0 255.255.255.0
NCHCO_splitTunnelAcl_1 list standard access allowed 192.168.2.0 255.255.255.0
AnyConnect_Client_Local_Print deny ip extended access list a whole
AnyConnect_Client_Local_Print list extended access permit tcp any any eq lpd
Note AnyConnect_Client_Local_Print of access list IPP: Internet Printing Protocol
AnyConnect_Client_Local_Print list extended access permit tcp any any eq 631
print the access-list AnyConnect_Client_Local_Print Note Windows port
AnyConnect_Client_Local_Print list extended access permit tcp any any eq 9100
access-list AnyConnect_Client_Local_Print mDNS Note: multicast DNS protocol
AnyConnect_Client_Local_Print list extended access permit udp any host 224.0.0.251 eq 5353
AnyConnect_Client_Local_Print of access list LLMNR Note: link Local Multicast Name Resolution protocol
AnyConnect_Client_Local_Print list extended access permit udp any host 224.0.0.252 eq 5355
Note access list TCP/NetBIOS protocol AnyConnect_Client_Local_Print
AnyConnect_Client_Local_Print list extended access permit tcp any any eq 137
AnyConnect_Client_Local_Print list extended access udp allowed any any eq netbios-ns
outside_access_in list extended access permit tcp any object FINX eq 3389
outside_access_in_1 list extended access allowed object rdp any object FINX
pager lines 24
Enable logging
asdm of logging of information
Within 1500 MTU
Outside 1500 MTU
mask of VPN_Pool VPN_Start VPN_End of local pool IP 255.255.255.0
ICMP unreachable rate-limit 1 burst-size 1
ASDM image disk0: / asdm - 649.bin
don't allow no asdm history
ARP timeout 14400
NAT (inside, all) static source NCHCO destination NCHCO static obj - 192.168.1.0 obj - 192.168.1.0
NAT (inside, all) static source any any destination static obj - 192.168.2.64 obj - 192.168.2.64
NAT (inside, all) source static obj - 0.0.0.0 0.0.0.0 - obj destination static obj - 192.168.2.64 obj - 192.168.2.64
!
network obj_any object
NAT dynamic interface (indoor, outdoor)
the FINX object network
NAT (inside, outside) interface static service tcp 3389 3389
Access-group outside_access_in_1 in interface outside
Route outside 0.0.0.0 0.0.0.0 69.61.228.177 1
Timeout xlate 03:00
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
dynamic-access-policy-registration DfltAccessPolicy
network-acl outside_nat0_outbound
WebVPN
SVC request to enable default svc
Enable http server
http 192.168.1.0 255.255.255.0 inside
http *. **. ***. 255.255.255.255 outside
http *. **. ***. 255.255.255.255 outside
http NCHCO 255.255.255.0 inside
http 96.11.251.186 255.255.255.255 outside
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown warmstart of cold start
Crypto ipsec transform-set ikev1 ESP-AES-128-SHA aes - esp esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-esp - aes esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-3DES-MD5-esp-3des esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-DES-SHA esp - esp-sha-hmac
Crypto ipsec transform-set ikev1 esp ESP-DES-MD5-esp-md5-hmac
Crypto ipsec transform-set esp-3des esp-sha-hmac ikev1 l2tp-transform
IKEv1 crypto ipsec transform-set l2tp-transformation mode transit
Crypto ipsec transform-set vpn-transform ikev1 esp-aes-256 esp-sha-hmac
Crypto ipsec transform-set esp-3des esp-sha-hmac TRANS_ESP_3DES_SHA ikev1
transport mode encryption ipsec transform-set TRANS_ESP_3DES_SHA ikev1
Crypto ipsec transform-set esp-3des esp-md5-hmac TRANS_ESP_3DES_MD5 ikev1
transport mode encryption ipsec transform-set TRANS_ESP_3DES_MD5 ikev1
Crypto ipsec transform-set ikev1 SHA-ESP-3DES esp-3des esp-sha-hmac
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 pfs Group1 set
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 define ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5
crypto dynamic-map dyn-map 10 set pfs Group1
crypto dynamic-map dyn-map 10 set transform-set l2tp vpn-transform processing ikev1
dynamic-map encryption dyn-map 10 value reverse-road
Crypto-map dynamic outside_dyn_map 20 set transform-set ESP-3DES-SHA ikev1
Crypto-map dynamic outside_dyn_map 20 the value reverse-road
card crypto outside_map 1 match address outside_1_cryptomap
card crypto outside_map 1 set pfs Group1
peer set card crypto outside_map 1 74.219.208.50
card crypto outside_map 1 set transform-set ESP-3DES-SHA ikev1
map outside_map 20-isakmp ipsec crypto dynamic outside_dyn_map
outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP
outside_map interface card crypto outside
inside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP
inside crypto map inside_map interface
card crypto vpn-map 1 match address outside_1_cryptomap_1
card crypto vpn-card 1 set pfs Group1
set vpn-card crypto map peer 1 74.219.208.50
card crypto 1 set transform-set ESP-3DES-SHA ikev1 vpn-map
dynamic vpn-map 10 dyn-map ipsec isakmp crypto map
crypto isakmp identity address
Crypto ikev1 allow inside
Crypto ikev1 allow outside
IKEv1 crypto ipsec-over-tcp port 10000
IKEv1 crypto policy 10
preshared authentication
3des encryption
md5 hash
Group 2
life 86400
IKEv1 crypto policy 15
preshared authentication
aes-256 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 35
preshared authentication
3des encryption
sha hash
Group 2
life 86400
enable client-implementation to date
Telnet 192.168.1.0 255.255.255.0 inside
Telnet NCHCO 255.255.255.0 inside
Telnet timeout 5
SSH 192.168.1.0 255.255.255.0 inside
SSH NCHCO 255.255.255.0 inside
SSH timeout 5
Console timeout 0
dhcpd address 192.168.2.150 - 192.168.2.225 inside
dhcpd dns 216.68.4.10 216.68.5.10 interface inside
lease interface 64000 dhcpd inside
!
a basic threat threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
WebVPN
internal DefaultRAGroup group strategy
attributes of Group Policy DefaultRAGroup
value of server DNS 192.168.2.1
L2TP ipsec VPN-tunnel-Protocol ikev1
nchco.local value by default-field
attributes of Group Policy DfltGrpPolicy
value of server DNS 192.168.2.1
L2TP ipsec VPN-tunnel-Protocol ikev1 ssl-clientless ssl-client
allow password-storage
enable IPSec-udp
enable dhcp Intercept 255.255.255.0
the address value VPN_Pool pools
internal NCHCO group policy
NCHCO group policy attributes
value of 192.168.2.1 DNS Server 8.8.8.8
Ikev1 VPN-tunnel-Protocol
Split-tunnel-policy tunnelspecified
value of Split-tunnel-network-list NCHCO_splitTunnelAcl_1
value by default-field NCHCO.local
admin LbMiJuAJjDaFb2uw encrypted privilege 15 password username
username privilege 15 encrypted password yB1lHEVmHZGj5C2Z 8njferg
username NCHvpn99 password dhn. JzttvRmMbHsP encrypted
attributes global-tunnel-group DefaultRAGroup
address (inside) VPN_Pool pool
address pool VPN_Pool
authentication-server-group (inside) LOCAL
authentication-server-group (outside LOCAL)
LOCAL authority-server-group
authorization-server-group (inside) LOCAL
authorization-server-group (outside LOCAL)
Group Policy - by default-DefaultRAGroup
band-Kingdom
band-band
IPSec-attributes tunnel-group DefaultRAGroup
IKEv1 pre-shared-key *.
NOCHECK Peer-id-validate
tunnel-group DefaultRAGroup ppp-attributes
No chap authentication
no authentication ms-chap-v1
ms-chap-v2 authentication
tunnel-group DefaultWEBVPNGroup ppp-attributes
PAP Authentication
ms-chap-v2 authentication
tunnel-group 74.219.208.50 type ipsec-l2l
IPSec-attributes tunnel-group 74.219.208.50
IKEv1 pre-shared-key *.
type tunnel-group NCHCO remote access
attributes global-tunnel-group NCHCO
address pool VPN_Pool
Group Policy - by default-NCHCO
IPSec-attributes tunnel-group NCHCO
IKEv1 pre-shared-key *.
!
class-map inspection_default
match default-inspection-traffic
!
!
type of policy-card inspect dns preset_dns_map
parameters
maximum message length automatic of customer
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the preset_dns_map dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
inspect the rsh
inspect the rtsp
inspect esmtp
inspect sqlnet
inspect the skinny
inspect sunrpc
inspect xdmcp
inspect the sip
inspect the netbios
inspect the tftp
Review the ip options
!
global service-policy global_policy
context of prompt hostname
call-home
Profile of CiscoTAC-1
no active account
http https://tools.cisco.com/its/service/oddce/services/DDCEService destination address
email address of destination [email protected] / * /
destination-mode http transport
Subscribe to alert-group diagnosis
Subscribe to alert-group environment
Subscribe to alert-group monthly periodic inventory
monthly periodicals to subscribe to alert-group configuration
daily periodic subscribe to alert-group telemetry
Cryptochecksum:a2110206e1af06974c858fb40c6de2fc
: end
ASDM image disk0: / asdm - 649.bin
ASDM VPN_Start 255.255.255.255 inside location
ASDM VPN_End 255.255.255.255 inside location
don't allow no asdm history
---------------------------------------------------------------------------------------------------------------
And here are the logs of the Cisco VPN Client when sailing, then is unable to browse the network behind the ASA:
---------------------------------------------------------------------------------------------------------------
Cisco Systems VPN Client Version 5.0.07.0440
Copyright (C) 1998-2010 Cisco Systems, Inc.. All rights reserved.
Customer type: Windows, Windows NT
Running: 6.1.7601 Service Pack 1
Config files directory: C:\Program Files (x 86) \Cisco Systems\VPN Client\
1 09:44:55.677 01/10/13 Sev = Info/6 CERT / 0 x 63600026
Try to find a certificate using hash Serial.
2 09:44:55.677 01/10/13 Sev = Info/6 CERT / 0 x 63600027
Found a certificate using hash Serial.
3 09:44:55.693 01/10/13 Sev = Info/6 GUI/0x63B00011
RELOADED successfully certificates in all certificate stores.
4 09:45:02.802 10/01/13 Sev = Info/4 CM / 0 x 63100002
Start the login process
5 09:45:02.802 01/10/13 Sev = Info/4 CM / 0 x 63100004
Establish a secure connection
6 09:45:02.802 01/10/13 Sev = Info/4 CM / 0 x 63100024
Attempt to connect with the server "*." **. ***. *** »
7 09:45:02.802 10/01/13 Sev = Info/6 IKE/0x6300003B
Try to establish a connection with *. **. ***. ***.
8 09:45:02.818 10/01/13 Sev = Info/4 IKE / 0 x 63000001
From IKE Phase 1 negotiation
9 09:45:02.865 10/01/13 Sev = Info/4 IKE / 0 x 63000013
SEND to > ISAKMP OAK AG (SA, KE, NO, ID, VID (Xauth), VID (dpd), VID (Frag), VID(Nat-T), VID (Unity)) to *. **. ***. ***
10 09:45:02.896 10/01/13 Sev = Info/5 IKE/0x6300002F
Received packet of ISAKMP: peer = *. **. ***. ***
11 09:45:02.896 10/01/13 Sev = Info/4 IKE / 0 x 63000014
RECEIVING< isakmp="" oak="" ag="" (sa,="" ke,="" non,="" id,="" hash,="" vid(unity),="" vid(xauth),="" vid(dpd),="" vid(nat-t),="" nat-d,="" nat-d,="" vid(frag),="" vid(?))="" from="">
12 09:45:02.896 10/01/13 Sev = Info/5 IKE / 0 x 63000001
Peer is a compatible peer Cisco-Unity
13 09:45:02.896 01/10/13 Sev = Info/5 IKE / 0 x 63000001
Peer supports XAUTH
14 09:45:02.896 01/10/13 Sev = Info/5 IKE / 0 x 63000001
Peer supports the DPD
15 09:45:02.896 01/10/13 Sev = Info/5 IKE / 0 x 63000001
Peer supports NAT - T
16 09:45:02.896 01/10/13 Sev = Info/5 IKE / 0 x 63000001
Peer supports fragmentation IKE payloads
17 09:45:02.927 01/10/13 Sev = Info/6 IKE / 0 x 63000001
IOS Vendor ID successful construction
18 09:45:02.927 01/10/13 Sev = Info/4 IKE / 0 x 63000013
SENDING > ISAKMP OAK AG * (HASH, NOTIFY: NAT - D, NAT - D, VID (?), STATUS_INITIAL_CONTACT, VID (Unity)) to *. **. ***. ***
19 09:45:02.927 01/10/13 Sev = Info/4 IKE / 0 x 63000083
IKE port in use - Local Port = 0xDD3B, Remote Port = 0x01F4
20 09:45:02.927 01/10/13 Sev = Info/5 IKE / 0 x 63000072
Automatic NAT detection status:
Remote endpoint is NOT behind a NAT device
This effect is NOT behind a NAT device
21 09:45:02.927 01/10/13 Sev = Info/4 CM/0x6310000E
ITS established Phase 1. 1 crypto IKE Active SA, 0 IKE SA authenticated user in the system
22 09:45:02.943 10/01/13 Sev = Info/5 IKE/0x6300002F
Received packet of ISAKMP: peer = *. **. ***. ***
23 09:45:02.943 01/10/13 Sev = Info/4 IKE / 0 x 63000014
RECEIVING< isakmp="" oak="" trans="" *(hash,="" attr)="" from="">
24 09:45:02.943 01/10/13 Sev = Info/4 CM / 0 x 63100015
Launch application xAuth
25 09:45:03.037 01/10/13 Sev = Info/6 GUI/0x63B00012
Attributes of the authentication request is 6: 00.
26 09:45:03.037 01/10/13 Sev = Info/4 CM / 0 x 63100017
xAuth application returned
27 09:45:03.037 10/01/13 Sev = Info/4 IKE / 0 x 63000013
SEND to > ISAKMP OAK TRANS *(HASH, ATTR) to *. **. ***. ***
28 09:45:03.037 10/01/13 Sev = Info/4 IPSEC / 0 x 63700008
IPSec driver started successfully
29 09:45:03.037 01/10/13 Sev = Info/4 IPSEC / 0 x 63700014
Remove all keys
30 09:45:03.083 01/10/13 Sev = Info/5 IKE/0x6300002F
Received packet of ISAKMP: peer = *. **. ***. ***
31 09:45:03.083 01/10/13 Sev = Info/4 IKE / 0 x 63000014
RECEIVING< isakmp="" oak="" trans="" *(hash,="" attr)="" from="">
32 09:45:03.083 01/10/13 Sev = Info/4 IKE / 0 x 63000013
SEND to > ISAKMP OAK TRANS *(HASH, ATTR) to *. **. ***. ***
33 09:45:03.083 01/10/13 Sev = Info/4 CM/0x6310000E
ITS established Phase 1. 1 crypto IKE Active SA, 1 IKE SA authenticated user in the system
34 09:45:03.083 01/10/13 Sev = Info/5 IKE/0x6300005E
Customer address a request from firewall to hub
35 09:45:03.083 01/10/13 Sev = Info/4 IKE / 0 x 63000013
SEND to > ISAKMP OAK TRANS *(HASH, ATTR) to *. **. ***. ***
36 09:45:03.146 01/10/13 Sev = Info/5 IKE/0x6300002F
Received packet of ISAKMP: peer = *. **. ***. ***
37 09:45:03.146 01/10/13 Sev = Info/4 IKE / 0 x 63000014
RECEIVING< isakmp="" oak="" trans="" *(hash,="" attr)="" from="" **.**.***.***="" isakmp="" oak="" trans="" *(hash,="" attr)="" from="">
38 09:45:03.146 01/10/13 Sev = Info/5 IKE / 0 x 63000010
MODE_CFG_REPLY: Attribute = INTERNAL_IPV4_ADDRESS:, value = 192.168.2.70
39 09:45:03.146 01/10/13 Sev = Info/5 IKE / 0 x 63000010
MODE_CFG_REPLY: Attribute = INTERNAL_IPV4_NETMASK:, value = 255.255.255.0
40 09:45:03.146 01/10/13 Sev = Info/5 IKE / 0 x 63000010
MODE_CFG_REPLY: Attribute = INTERNAL_IPV4_DNS (1):, value = 192.168.2.1
41 09:45:03.146 01/10/13 Sev = Info/5 IKE / 0 x 63000010
MODE_CFG_REPLY: Attribute = INTERNAL_IPV4_DNS (2):, value = 8.8.8.8
42 09:45:03.146 01/10/13 Sev = Info/5 IKE/0x6300000D
MODE_CFG_REPLY: Attribute = MODECFG_UNITY_SAVEPWD:, value = 0x00000001
43 09:45:03.146 01/10/13 Sev = Info/5 IKE/0x6300000D
MODE_CFG_REPLY: Attribute = MODECFG_UNITY_SPLIT_INCLUDE (# of split_nets), value = 0x00000001
44 09:45:03.146 10/01/13 Sev = Info/5 IKE/0x6300000F
SPLIT_NET #1
= 192.168.2.0 subnet
mask = 255.255.255.0
Protocol = 0
SRC port = 0
port dest = 0
45 09:45:03.146 10/01/13 Sev = Info/5 IKE/0x6300000E
MODE_CFG_REPLY: Attribute = MODECFG_UNITY_DEFDOMAIN:, value = NCHCO.local
46 09:45:03.146 01/10/13 Sev = Info/5 IKE/0x6300000D
MODE_CFG_REPLY: Attribute = MODECFG_UNITY_UDP_NAT_PORT, value = 0 x 00002710
47 09:45:03.146 01/10/13 Sev = Info/5 IKE/0x6300000D
MODE_CFG_REPLY: Attribute = MODECFG_UNITY_PFS:, value = 0x00000000
48 09:45:03.146 01/10/13 Sev = Info/5 IKE/0x6300000E
MODE_CFG_REPLY: Attribute = APPLICATION_VERSION, value = 8.4 (1) Cisco systems, Inc. ASA5505 Version built by manufacturers on Tuesday, January 31, 11 02:11
49 09:45:03.146 01/10/13 Sev = Info/5 IKE/0x6300000D
MODE_CFG_REPLY: Attribute = MODECFG_UNITY_SMARTCARD_REMOVAL_DISCONNECT:, value = 0x00000001
50 09:45:03.146 01/10/13 Sev = Info/4 CM / 0 x 63100019
Data in mode Config received
51 09:45:03.146 01/10/13 Sev = Info/4 IKE / 0 x 63000056
Received a request from key driver: local IP = 192.168.2.70, GW IP = *. **. ***. remote IP address = 0.0.0.0
52 09:45:03.146 01/10/13 Sev = Info/4 IKE / 0 x 63000013
SEND to > ISAKMP OAK QM * (HASH, SA, NO, ID, ID) to *. **. ***. ***
53 09:45:03.177 01/10/13 Sev = Info/5 IKE/0x6300002F
Received packet of ISAKMP: peer = *. **. ***. ***
54 09:45:03.177 01/10/13 Sev = Info/4 IKE / 0 x 63000014
RECEIVING< isakmp="" oak="" info="" *(hash,="" notify:status_resp_lifetime)="" from="">
55 09:45:03.177 01/10/13 Sev = Info/5 IKE / 0 x 63000045
Answering MACHINE-LIFE notify has value of 86400 seconds
56 09:45:03.177 01/10/13 Sev = Info/5 IKE / 0 x 63000047
This SA was already alive for 1 second, expiration of adjustment to 86399 seconds now
57 09:45:03.193 01/10/13 Sev = Info/5 IKE/0x6300002F
Received packet of ISAKMP: peer = *. **. ***. ***
58 09:45:03.193 01/10/13 Sev = Info/4 IKE / 0 x 63000014
RECEIVING< isakmp="" oak="" qm="" *(hash,="" sa,="" non,="" id,="" id,="" notify:status_resp_lifetime)="" from="">
59 09:45:03.193 01/10/13 Sev = Info/5 IKE / 0 x 63000045
Answering MACHINE-LIFE notify is set to 28800 seconds
60 09:45:03.193 01/10/13 Sev = Info/4 IKE / 0 x 63000013
SEND to > ISAKMP OAK QM * (HASH) to *. **. ***. ***
61 09:45:03.193 01/10/13 Sev = Info/5 IKE / 0 x 63000059
IPsec Security Association of loading (MsgID = SPI OUTBOUND SPI INCOMING = 0x3EBEBFC5 0xAAAF4C1C = 967A3C93)
62 09:45:03.193 01/10/13 Sev = Info/5 IKE / 0 x 63000025
OUTGOING ESP SPI support: 0xAAAF4C1C
63 09:45:03.193 01/10/13 Sev = Info/5 IKE / 0 x 63000026
Charges INBOUND ESP SPI: 0x3EBEBFC5
64 09:45:03.193 01/10/13 Sev = Info/5 CVPND / 0 x 63400013
Destination mask subnet Gateway Interface metric
0.0.0.0 0.0.0.0 96.11.251.1 96.11.251.149 261
96.11.251.0 255.255.255.0 96.11.251.149 96.11.251.149 261
96.11.251.149 255.255.255.255 96.11.251.149 96.11.251.149 261
96.11.251.255 255.255.255.255 96.11.251.149 96.11.251.149 261
127.0.0.0 255.0.0.0 127.0.0.1 127.0.0.1 306
127.0.0.1 255.255.255.255 127.0.0.1 127.0.0.1 306
127.255.255.255 255.255.255.255 127.0.0.1 127.0.0.1 306
192.168.1.0 255.255.255.0 192.168.1.3 192.168.1.3 261
192.168.1.3 255.255.255.255 192.168.1.3 192.168.1.3 261
192.168.1.255 255.255.255.255 192.168.1.3 192.168.1.3 261
224.0.0.0 240.0.0.0 127.0.0.1 127.0.0.1 306
224.0.0.0 240.0.0.0 96.11.251.149 96.11.251.149 261
224.0.0.0 240.0.0.0 192.168.1.3 192.168.1.3 261
255.255.255.255 255.255.255.255 127.0.0.1 127.0.0.1 306
255.255.255.255 255.255.255.255 96.11.251.149 96.11.251.149 261
255.255.255.255 255.255.255.255 192.168.1.3 192.168.1.3 261
65 09:45:03.521 01/10/13 Sev = Info/6 CVPND / 0 x 63400001
Launch VAInst64 for controlling IPSec virtual card
66 09:45:03.896 01/10/13 Sev = Info/4 CM / 0 x 63100034
The virtual card has been activated:
IP=192.168.2.70/255.255.255.0
DNS = 192.168.2.1, 8.8.8.8
WINS = 0.0.0.0 0.0.0.0
Domain = NCHCO.local
Split = DNS names
67 09:45:03.912 01/10/13 Sev = Info/5 CVPND / 0 x 63400013
Destination mask subnet Gateway Interface metric
0.0.0.0 0.0.0.0 96.11.251.1 96.11.251.149 261
96.11.251.0 255.255.255.0 96.11.251.149 96.11.251.149 261
96.11.251.149 255.255.255.255 96.11.251.149 96.11.251.149 261
96.11.251.255 255.255.255.255 96.11.251.149 96.11.251.149 261
127.0.0.0 255.0.0.0 127.0.0.1 127.0.0.1 306
127.0.0.1 255.255.255.255 127.0.0.1 127.0.0.1 306
127.255.255.255 255.255.255.255 127.0.0.1 127.0.0.1 306
192.168.1.0 255.255.255.0 192.168.1.3 192.168.1.3 261
192.168.1.3 255.255.255.255 192.168.1.3 192.168.1.3 261
192.168.1.255 255.255.255.255 192.168.1.3 192.168.1.3 261
224.0.0.0 240.0.0.0 127.0.0.1 127.0.0.1 306
224.0.0.0 240.0.0.0 96.11.251.149 96.11.251.149 261
224.0.0.0 240.0.0.0 192.168.1.3 192.168.1.3 261
224.0.0.0 240.0.0.0 0.0.0.0 0.0.0.0 261
255.255.255.255 255.255.255.255 127.0.0.1 127.0.0.1 306
255.255.255.255 255.255.255.255 96.11.251.149 96.11.251.149 261
255.255.255.255 255.255.255.255 192.168.1.3 192.168.1.3 261
255.255.255.255 255.255.255.255 0.0.0.0 0.0.0.0 261
68 09:45:07.912 01/10/13 Sev = Info/4 CM / 0 x 63100038
Were saved successfully road to file changes.
69 09:45:07.912 01/10/13 Sev = Info/5 CVPND / 0 x 63400013
Destination mask subnet Gateway Interface metric
0.0.0.0 0.0.0.0 96.11.251.1 96.11.251.149 261
**. **. ***. 255.255.255.255 96.11.251.1 96.11.251.149 100
96.11.251.0 255.255.255.0 96.11.251.149 96.11.251.149 261
96.11.251.149 255.255.255.255 96.11.251.149 96.11.251.149 261
96.11.251.255 255.255.255.255 96.11.251.149 96.11.251.149 261
127.0.0.0 255.0.0.0 127.0.0.1 127.0.0.1 306
127.0.0.1 255.255.255.255 127.0.0.1 127.0.0.1 306
127.255.255.255 255.255.255.255 127.0.0.1 127.0.0.1 306
192.168.1.0 255.255.255.0 192.168.1.3 192.168.1.3 261
192.168.1.3 255.255.255.255 192.168.1.3 192.168.1.3 261
192.168.1.255 255.255.255.255 192.168.1.3 192.168.1.3 261
192.168.2.0 255.255.255.0 192.168.2.70 192.168.2.70 261
192.168.2.0 255.255.255.0 192.168.2.1 192.168.2.70 100
192.168.2.70 255.255.255.255 192.168.2.70 192.168.2.70 261
192.168.2.255 255.255.255.255 192.168.2.70 192.168.2.70 261
224.0.0.0 240.0.0.0 127.0.0.1 127.0.0.1 306
224.0.0.0 240.0.0.0 96.11.251.149 96.11.251.149 261
224.0.0.0 240.0.0.0 192.168.1.3 192.168.1.3 261
224.0.0.0 240.0.0.0 192.168.2.70 192.168.2.70 261
255.255.255.255 255.255.255.255 127.0.0.1 127.0.0.1 306
255.255.255.255 255.255.255.255 96.11.251.149 96.11.251.149 261
255.255.255.255 255.255.255.255 192.168.1.3 192.168.1.3 261
255.255.255.255 255.255.255.255 192.168.2.70 192.168.2.70 261
70 09:45:07.912 01/10/13 Sev = Info/6 CM / 0 x 63100036
The routing table has been updated for the virtual card
71 09:45:07.912 01/10/13 Sev = Info/4 CM/0x6310001A
A secure connection established
72 09:45:07.943 01/10/13 Sev = Info/4 CM/0x6310003B
Look at address added to 96.11.251.149. Current host name: psaserver, current address (s): 192.168.2.70, 96.11.251.149, 192.168.1.3.
73 09:45:07.943 01/10/13 Sev = Info/4 CM/0x6310003B
Look at address added to 192.168.2.70. Current host name: psaserver, current address (s): 192.168.2.70, 96.11.251.149, 192.168.1.3.
74 09:45:07.943 01/10/13 Sev = Info/5 CM / 0 x 63100001
Did not find the smart card to watch for removal
75 09:45:07.943 01/10/13 Sev = Info/4 IPSEC / 0 x 63700014
Remove all keys
76 09:45:07.943 01/10/13 Sev = Info/4 IPSEC / 0 x 63700010
Creates a new key structure
77 09:45:07.943 01/10/13 Sev = Info/4 IPSEC/0x6370000F
Adding key with SPI = 0x1c4cafaa in the list of keys
78 09:45:07.943 01/10/13 Sev = Info/4 IPSEC / 0 x 63700010
Creates a new key structure
79 09:45:07.943 01/10/13 Sev = Info/4 IPSEC/0x6370000F
Adding key with SPI = 0xc5bfbe3e in the list of keys
80 09:45:07.943 01/10/13 Sev = Info/4 IPSEC/0x6370002F
Assigned WILL interface private addr 192.168.2.70
81 09:45:07.943 01/10/13 Sev = Info/4 IPSEC / 0 x 63700037
Configure the public interface: 96.11.251.149. SG: **.**.***.***
82 09:45:07.943 10/01/13 Sev = Info/6 CM / 0 x 63100046
Define indicator tunnel set up in the registry to 1.
83 09:45:13.459 01/10/13 Sev = Info/4 IKE / 0 x 63000013
SEND to > ISAKMP OAK INFO * (HASH, NOTIFY: DPD_REQUEST) to *. **. ***. ***
84 09:45:13.459 01/10/13 Sev = Info/6 IKE/0x6300003D
Upon request of the DPD to *. **. ***. , our seq # = 107205276
85 09:45:13.474 01/10/13 Sev = Info/5 IKE/0x6300002F
Received packet of ISAKMP: peer = *. **. ***. ***
86 09:45:13.474 01/10/13 Sev = Info/4 IKE / 0 x 63000014
RECEIVING< isakmp="" oak="" info="" *(hash,="" notify:dpd_ack)="" from="">
87 09:45:13.474 01/10/13 Sev = Info/5 IKE / 0 x 63000040
Receipt of DPO ACK to *. **. ***. seq # receipt = 107205276, seq # expected is 107205276
88 09:45:15.959 01/10/13 Sev = Info/4 IPSEC / 0 x 63700019
Activate key dating SPI = 0x1c4cafaa key with SPI = 0xc5bfbe3e
89 09:46:00.947 10/01/13 Sev = Info/4 IKE / 0 x 63000013
SEND to > ISAKMP OAK INFO * (HASH, NOTIFY: DPD_REQUEST) to *. **. ***. ***
90 09:46:00.947 01/10/13 Sev = Info/6 IKE/0x6300003D
Upon request of the DPD to *. **. ***. , our seq # = 107205277
91 09:46:01.529 01/10/13 Sev = Info/5 IKE/0x6300002F
Received packet of ISAKMP: peer = *. **. ***. ***
92 09:46:01.529 01/10/13 Sev = Info/4 IKE / 0 x 63000014
RECEIVING< isakmp="" oak="" info="" *(hash,="" notify:dpd_ack)="" from="">
93 09:46:01.529 01/10/13 Sev = Info/5 IKE / 0 x 63000040
Receipt of DPO ACK to *. **. ***. seq # receipt = 107205277, seq # expected is 107205277
94 09:46:11.952 01/10/13 Sev = Info/4 IKE / 0 x 63000013
SEND to > ISAKMP OAK INFO * (HASH, NOTIFY: DPD_REQUEST) to *. **. ***. ***
95 09:46:11.952 01/10/13 Sev = Info/6 IKE/0x6300003D
Upon request of the DPD to *. **. ***. , our seq # = 107205278
96 09:46:11.979 01/10/13 Sev = Info/5 IKE/0x6300002F
Received packet of ISAKMP: peer = *. **. ***. ***
97 09:46:11.979 01/10/13 Sev = Info/4 IKE / 0 x 63000014
RECEIVING< isakmp="" oak="" info="" *(hash,="" notify:dpd_ack)="" from="">
98 09:46:11.979 01/10/13 Sev = Info/5 IKE / 0 x 63000040
Receipt of DPO ACK to *. **. ***. seq # receipt = 107205278, seq # expected is 107205278
---------------------------------------------------------------------------------------------------------------
Any help would be appreciated, thanks!
try to refuse the ACL (access-list AnyConnect_Client_Local_Print extended deny ip any one) at the end of the ACL.
-
Currently I have a cisco asa 5505 y tengo problemas debido that put users no will can connect, cisco don't me you can antender porque mi garantia expired, habra dd can help me Porfavor quien contrato.
Gracias Desde are
Claro [email protected] / * /
-
How to establish a tunnel vpn ipsec using DNS with ASA 5505?
Hello
I m get a dynamic IP address public and what I m trying to do is establish a tunnnel remote vpn using IPSec, which I realize my provider but each time resets of sessions or ASA 5505 reset, I get a new public IP and I need to put the new IP address on the remote client, so I can establish the vpn...
How can I establish a vpn ipsec using DNS? For this scenario, the remote client vpn is a vpn phone, but it could be any vpn client.
Private private Public IP IP IP
PBX - Telephone (LAN) - ASA 5505-(Internet)-(router) Remote Site-(LAN) VPN-
Kind regards!
Ah ok I see, Yes in this case there is no that you can do other than request a static IP address from your ISP.
Kind regards.
PS: Don't forget to mark this question as answered. Thank you!
-
Client VPN Cisco ASA 5505 Cisco 1841 router
Hello. I'm doing a connection during a cisco vpn client and a vpn on one server asa 5505 behind a 1841 router (internet adsl2 + and NAT router).
My topology is almost as follows
customer - tunnel - 1841 - ASA - PC
ASA is the endpoint vpn (outside interface) device. I forward udp port 500 and 4500 on my router to the ASA and the tunnel rises. I exempt nat'ting on the asa and the router to the IP in dhcp vpn pool. I can connect to my tunnel but I can't "see" anything in the internal network. I allowed all traffic from the outside inwards buy from the ip vpn pool and I still send packets through the tunnel and I get nothing. I take a look at the statistics on the vpn client and I 2597 bytes (ping traffic) and there are no bytes. Any idea?
Where you you logged in when you took the "crypto ipsec to show his"? If this isn't the case then try again, also this option allows IPSEC over UDP 4500 and it is disabled, enable it.
ISAKMP nat-traversal crypto
Just enter the command as it is, then try to connect again after activation of this option and get the same result to see the.
-
Please give index on configuring vpn site to site on 881 to ASA 5505 cisco router
Earlier my boss asked me to prepare to implement the VPN site-to site on router Cisco 881 Integrated Services to ASA 5505 router, which is now running on the side of HQ. Someone please give me a hint. I am now learning the pdf file from Cisco that mention how to configure VPN site to site between 1812 Cisco IOS router and router of the ASA 5505 using ASDM V6.1 and SDM V2.5. Cannot find the book for the Cisco 881 device.
Someone please please suggest me something as soon as POSSIBLE.
Thank you
CLI version:
ASDM and SDM Version:
-
Cisco ASA 5505 VPN Site to Site
Hi all
First post on the forums. I have worked with Cisco ASA 5505 for a few months and I recently bought a 2nd ASA to implement tunnel VPN Site to Site. It seems so simple in the number of videos watched on the internet. But when I did he surprise it did work for me... I've removed the tunnels, a number of times and tried to recreate. I use the VPN Wizard in the SMA to create the tunnel. Both the asa 5505 of are and have the same firmware even etc..
I'd appreciate any help that can be directed to this problem please. Slowly losing my mind
Please see details below:
Two ADMS are 7.1
IOS
ASA 1
Nadia
:
ASA Version 9.0 (1)
!
hostname PAYBACK
activate the encrypted password of HSMurh79NVmatjY0
volatile xlate deny tcp any4 any4
volatile xlate deny tcp any4 any6
volatile xlate deny tcp any6 any4
volatile xlate deny tcp any6 any6
volatile xlate deny udp any4 any4 eq field
volatile xlate deny udp any4 any6 eq field
volatile xlate deny udp any6 any4 eq field
volatile xlate deny udp any6 any6 eq field
2KFQnbNIdI.2KYOU encrypted passwd
names of
local pool VPN1 192.168.50.1 - 192.168.50.254 255.255.255.0 IP mask
!
interface Ethernet0/0
switchport access vlan 2
Speed 100
full duplex
!
interface Ethernet0/1
link Trunk Description of SW1
switchport trunk allowed vlan 1,10,20,30,40
switchport trunk vlan 1 native
switchport mode trunk
!
interface Ethernet0/2
!
interface Ethernet0/3
!
interface Ethernet0/4
!
interface Ethernet0/5
!
interface Ethernet0/6
!
interface Ethernet0/7
!
interface Vlan1
No nameif
no level of security
no ip address
!
interface Vlan2
nameif outside
security-level 0
IP 92.51.193.158 255.255.255.252
!
interface Vlan10
nameif inside
security-level 100
IP 192.168.10.1 255.255.255.0
!
interface Vlan20
nameif servers
security-level 100
address 192.168.20.1 255.255.255.0
!
Vlan30 interface
nameif printers
security-level 100
192.168.30.1 IP address 255.255.255.0
!
interface Vlan40
nameif wireless
security-level 100
192.168.40.1 IP address 255.255.255.0
!
connection line banner welcome to the Payback loyalty systems
boot system Disk0: / asa901 - k8.bin
passive FTP mode
summer time clock GMT/IDT recurring last Sun Mar 01:00 last Sun Oct 02:00
DNS domain-lookup outside
DNS lookup field inside
domain-lookup DNS servers
DNS lookup domain printers
DNS domain-lookup wireless
DNS server-group DefaultDNS
Server name 83.147.160.2
Server name 83.147.160.130
permit same-security-traffic inter-interface
network obj_any object
subnet 0.0.0.0 0.0.0.0
ftp_server network object
network of the Internal_Report_Server object
Home 192.168.20.21
Description address internal automated report server
network of the Report_Server object
Home 89.234.126.9
Description of server automated reports
service object RDP
service destination tcp 3389 eq
Description RDP to the server
network of the Host_QA_Server object
Home 89.234.126.10
Description QA host external address
network of the Internal_Host_QA object
Home 192.168.20.22
host of computer virtual Description for QA
network of the Internal_QA_Web_Server object
Home 192.168.20.23
Description Web Server in the QA environment
network of the Web_Server_QA_VM object
Home 89.234.126.11
Server Web Description in the QA environment
service object SQL_Server
destination eq 1433 tcp service
network of the Demo_Server object
Home 89.234.126.12
Description server set up for the product demo
network of the Internal_Demo_Server object
Home 192.168.20.24
Internal description of the demo server IP address
network of the NETWORK_OBJ_192.168.20.0_24 object
subnet 192.168.20.0 255.255.255.0
network of the NETWORK_OBJ_192.168.50.0_26 object
255.255.255.192 subnet 192.168.50.0
network of the NETWORK_OBJ_192.168.0.0_16 object
Subnet 192.168.0.0 255.255.0.0
service object MSSQL
destination eq 1434 tcp service
MSSQL port description
VPN network object
192.168.50.0 subnet 255.255.255.0
network of the NETWORK_OBJ_192.168.50.0_24 object
192.168.50.0 subnet 255.255.255.0
service object TS
tcp destination eq 4400 service
service of the TS_Return object
tcp source eq 4400 service
network of the External_QA_3 object
Home 89.234.126.13
network of the Internal_QA_3 object
Home 192.168.20.25
network of the Dev_WebServer object
Home 192.168.20.27
network of the External_Dev_Web object
Home 89.234.126.14
network of the CIX_Subnet object
255.255.255.0 subnet 192.168.100.0
network of the NETWORK_OBJ_192.168.10.0_24 object
192.168.10.0 subnet 255.255.255.0
network of the NETWORK_OBJ_84.39.233.50 object
Home 84.39.233.50
network of the NETWORK_OBJ_92.51.193.158 object
Home 92.51.193.158
network of the NETWORK_OBJ_192.168.100.0_24 object
255.255.255.0 subnet 192.168.100.0
network of the NETWORK_OBJ_192.168.1.0_24 object
subnet 192.168.1.0 255.255.255.0
object-group service DM_INLINE_SERVICE_1
the tcp destination eq ftp service object
the purpose of the tcp destination eq netbios-ssn service
the purpose of the tcp destination eq smtp service
service-object TS
the Payback_Internal object-group network
object-network 192.168.10.0 255.255.255.0
object-network 192.168.20.0 255.255.255.0
object-network 192.168.40.0 255.255.255.0
object-group service DM_INLINE_SERVICE_3
the purpose of the service tcp destination eq www
the purpose of the tcp destination eq https service
service-object TS
service-object, object TS_Return
object-group service DM_INLINE_SERVICE_4
service-object RDP
the purpose of the service tcp destination eq www
the purpose of the tcp destination eq https service
object-group service DM_INLINE_SERVICE_5
purpose purpose of the MSSQL service
service-object RDP
service-object TS
object-group Protocol TCPUDP
object-protocol udp
object-tcp protocol
object-group service DM_INLINE_SERVICE_6
service-object TS
service-object, object TS_Return
the purpose of the service tcp destination eq www
the purpose of the tcp destination eq https service
Note to outside_access_in to access list that this rule allows Internet the interal server.
Notice on the outside_access_in of the access-list allowed:
Comment from outside_access_in-list of FTP access
Comment from outside_access_in-RDP access list
Comment from outside_access_in-list of SMTP access
Note to outside_access_in to access list Net Bios
Comment from outside_access_in-SQL access list
Comment from outside_access_in-list to access TS - 4400
outside_access_in list extended access allowed object object-group DM_INLINE_SERVICE_1 any4 Internal_Report_Server
access host access-list outside_access_in note rule internal QA
Notice on the outside_access_in of the access-list allowed:
Comment from outside_access_in-HTTP access list
Comment from outside_access_in-RDP access list
outside_access_in list extended access permitted tcp any4 object Internal_Host_QA eq www
Notice on the outside_access_in of the access-list access to the internal Web server:
Notice on the outside_access_in of the access-list allowed:
Comment from outside_access_in-HTTP access list
Comment from outside_access_in-RDP access list
outside_access_in list extended access allowed object object-group DM_INLINE_SERVICE_3 any4 Internal_QA_Web_Server
Note to outside_access_in to access list rule allowing access to the demo server
Notice on the outside_access_in of the access-list allowed:
Comment from outside_access_in-RDP access list
Comment from outside_access_in-list to access MSSQL
outside_access_in list extended access allowed object object-group DM_INLINE_SERVICE_4 any4 Internal_Demo_Server
outside_access_in list extended access allowed object-group DM_INLINE_SERVICE_5 any object Internal_QA_3
Note to outside_access_in access to the development Web server access list
outside_access_in list extended access allowed object-group DM_INLINE_SERVICE_6 any object Dev_WebServer
AnyConnect_Client_Local_Print deny any4 any4 ip extended access list
AnyConnect_Client_Local_Print list extended access permitted tcp any4 any4 eq lpd
Note AnyConnect_Client_Local_Print of access list IPP: Internet Printing Protocol
AnyConnect_Client_Local_Print list extended access permitted tcp any4 any4 eq 631
print the access-list AnyConnect_Client_Local_Print Note Windows port
AnyConnect_Client_Local_Print list extended access permitted tcp any4 any4 eq 9100
access-list AnyConnect_Client_Local_Print mDNS Note: multicast DNS protocol
AnyConnect_Client_Local_Print list extended access permit udp host 224.0.0.251 any4 eq 5353
AnyConnect_Client_Local_Print of access list LLMNR Note: link Local Multicast Name Resolution protocol
AnyConnect_Client_Local_Print list extended access permit udp host 224.0.0.252 any4 eq 5355
Note access list TCP/NetBIOS protocol AnyConnect_Client_Local_Print
AnyConnect_Client_Local_Print list extended access permitted tcp any4 any4 EQ. 137
AnyConnect_Client_Local_Print list extended access permitted udp any4 any4 eq netbios-ns
Payback_VPN_splitTunnelAcl list standard access allowed 192.168.20.0 255.255.255.0
permit outside_cryptomap to access extended list ip 192.168.10.0 255.255.255.0 192.168.100.0 255.255.255.0
pager lines 24
Enable logging
information recording console
asdm of logging of information
address record
the journaling recipient
level alerts
Outside 1500 MTU
Within 1500 MTU
MTU 1500 servers
MTU 1500 printers
MTU 1500 wireless
no failover
ICMP unreachable rate-limit 1 burst-size 1
ASDM image disk0: / asdm-711 - 52.bin
don't allow no asdm history
ARP timeout 14400
no permit-nonconnected arp
NAT (inside, outside) source Dynamics one interface
NAT (wireless, outdoors) source Dynamics one interface
NAT (servers, outside) no matter what source dynamic interface
NAT (servers, external) static source Internal_Report_Server Report_Server
NAT (servers, external) static source Internal_Host_QA Host_QA_Server
NAT (servers, external) static source Internal_QA_Web_Server Web_Server_QA_VM
NAT (servers, external) static source Internal_Demo_Server Demo_Server
NAT (servers, external) static source NETWORK_OBJ_192.168.20.0_24 NETWORK_OBJ_192.168.20.0_24 NETWORK_OBJ_192.168.50.0_24 NETWORK_OBJ_192.168.50.0_24 non-proxy-arp-search of route static destination
NAT (servers, external) static source Internal_QA_3 External_QA_3
NAT (servers, external) static source Dev_WebServer External_Dev_Web
NAT (inside, outside) static source NETWORK_OBJ_192.168.10.0_24 NETWORK_OBJ_192.168.10.0_24 NETWORK_OBJ_192.168.1.0_24 NETWORK_OBJ_192.168.1.0_24 non-proxy-arp-search of route static destination
NAT (inside, outside) static source NETWORK_OBJ_192.168.10.0_24 NETWORK_OBJ_192.168.10.0_24 NETWORK_OBJ_192.168.100.0_24 NETWORK_OBJ_192.168.100.0_24 non-proxy-arp-search of route static destination
Access-group outside_access_in in interface outside
Route outside 0.0.0.0 0.0.0.0 92.51.193.157 1
Timeout xlate 03:00
Pat-xlate timeout 0:00:30
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
Floating conn timeout 0:00:00
dynamic-access-policy-registration DfltAccessPolicy
identity of the user by default-domain LOCAL
the ssh LOCAL console AAA authentication
Enable http server
http 192.168.10.0 255.255.255.0 inside
http 192.168.40.0 255.255.255.0 wireless
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown cold start
Crypto ipsec transform-set ikev1 ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-DES-SHA esp - esp-sha-hmac
Crypto ipsec transform-set ikev1 esp ESP-DES-MD5-esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-3DES-MD5-esp-3des esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-128-SHA aes - esp esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-esp - aes esp-md5-hmac
Crypto ipsec transform-set ikev1 SHA-ESP-3DES esp-3des esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-128-SHA-TRANS-aes - esp esp-sha-hmac
Crypto ipsec ikev1 transform-set ESP-AES-128-SHA-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-TRANS-aes - esp esp-md5-hmac
Crypto ipsec ikev1 transform-set ESP-AES-128-MD5-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-AES-192-SHA-TRANS esp-aes-192 esp-sha-hmac
Crypto ipsec ikev1 transform-set ESP-AES-192-SHA-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-AES-192-MD5-TRANS esp-aes-192 esp-md5-hmac
Crypto ipsec ikev1 transform-set ESP-AES-192-MD5-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-AES-256-SHA-TRANS esp-aes-256 esp-sha-hmac
Crypto ipsec ikev1 transform-set ESP-AES-256-SHA-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-AES-256-MD5-TRANS esp-aes-256 esp-md5-hmac
Crypto ipsec ikev1 transform-set ESP-AES-256-MD5-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-3DES-SHA-TRANS esp-3des esp-sha-hmac
Crypto ipsec ikev1 transform-set ESP-3DES-SHA-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-3DES-MD5-TRANS esp-3des esp-md5-hmac
Crypto ipsec ikev1 transform-set ESP-3DES-MD5-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-DES-SHA-TRANS esp - esp-sha-hmac
Crypto ipsec ikev1 transform-set ESP-DES-SHA-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-DES-MD5-TRANS esp - esp-md5-hmac
Crypto ipsec ikev1 transform-set ESP-DES-MD5-TRANS mode transit
Crypto ipsec ikev2 AES256 ipsec-proposal
Protocol esp encryption aes-256
Esp integrity sha - 1, md5 Protocol
Crypto ipsec ikev2 ipsec-proposal AES192
Protocol esp encryption aes-192
Esp integrity sha - 1, md5 Protocol
Crypto ipsec ikev2 ipsec-proposal AES
Esp aes encryption protocol
Esp integrity sha - 1, md5 Protocol
Crypto ipsec ikev2 proposal ipsec 3DES
Esp 3des encryption protocol
Esp integrity sha - 1, md5 Protocol
Crypto ipsec ikev2 ipsec-proposal OF
encryption protocol esp
Esp integrity sha - 1, md5 Protocol
Crypto ipsec pmtu aging infinite - the security association
card crypto outside_map 1 match address outside_cryptomap
card crypto outside_map 1 set pfs
peer set card crypto outside_map 1 84.39.233.50
card crypto outside_map 1 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5
outside_map card crypto 1 set ikev2 AES256 AES192 AES 3DES ipsec-proposal OF
outside_map interface card crypto outside
trustpool crypto ca policy
IKEv2 crypto policy 1
aes-256 encryption
integrity sha
Group 5
FRP sha
second life 86400
IKEv2 crypto policy 10
aes-192 encryption
integrity sha
Group 5
FRP sha
second life 86400
IKEv2 crypto policy 20
aes encryption
integrity sha
Group 5
FRP sha
second life 86400
IKEv2 crypto policy 30
3des encryption
integrity sha
Group 5
FRP sha
second life 86400
IKEv2 crypto policy 40
the Encryption
integrity sha
Group 5
FRP sha
second life 86400
Crypto ikev2 activate out of service the customer port 443
Crypto ikev1 allow outside
IKEv1 crypto policy 10
preshared authentication
3des encryption
sha hash
Group 2
life 86400
Telnet timeout 5
SSH 77.75.100.208 255.255.255.240 outside
SSH 192.168.10.0 255.255.255.0 inside
SSH 192.168.40.0 255.255.255.0 wireless
SSH timeout 5
Console timeout 0dhcpd 192.168.0.1 dns
dhcpd outside auto_config
!
dhcpd address 192.168.10.21 - 192.168.10.240 inside
dhcpd dns 192.168.20.21 83.147.160.2 interface inside
paybackloyalty.com dhcpd option 15 inside ascii interface
dhcpd allow inside
!
dhcpd address 192.168.40.21 - 192.168.40.240 Wireless
dhcpd dns 192.168.20.21 83.147.160.2 wireless interface
dhcpd update dns of the wireless interface
dhcpd option 15 ascii paybackloyalty.com wireless interface
dhcpd activate wireless
!
a basic threat threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
internal Payback_VPN group strategy
attributes of Group Policy Payback_VPN
VPN - 10 concurrent connections
Ikev1 VPN-tunnel-Protocol
Split-tunnel-policy tunnelspecified
value of Split-tunnel-network-list Payback_VPN_splitTunnelAcl
attributes of Group Policy DfltGrpPolicy
value of 83.147.160.2 DNS server 83.147.160.130
VPN-tunnel-Protocol ikev1, ikev2 clientless ssl
internal GroupPolicy_84.39.233.50 group strategy
attributes of Group Policy GroupPolicy_84.39.233.50
VPN-tunnel-Protocol ikev1, ikev2
Noelle XB/IpvYaATP.2QYm username encrypted password
Noelle username attributes
VPN-group-policy Payback_VPN
type of remote access service
username Éanna encrypted password privilege 0 vXILR9ZZQIsd1Naw
Éanna attributes username
VPN-group-policy Payback_VPN
type of remote access service
Michael qpbleUqUEchRrgQX of encrypted password username
user name Michael attributes
VPN-group-policy Payback_VPN
type of remote access service
username, password from Danny .7fEXdzESUk6S/cC encrypted privilege 0
user name Danny attributes
VPN-group-policy Payback_VPN
type of remote access service
Aileen tytrelqvV5VRX2pz encrypted password privilege 0 username
user name Aileen attributes
VPN-group-policy Payback_VPN
type of remote access service
Aidan aDu6YH0V5XaxpEPg encrypted password privilege 0 username
Aidan username attributes
VPN-group-policy Payback_VPN
type of remote access service
username password 6e6Djaz3W/XH59zX gordon encrypted privilege 15
shane.c iqGMoWOnfO6YKXbw encrypted password username
username shane.c attributes
VPN-group-policy Payback_VPN
type of remote access service
Shane uYePLcrFadO9pBZx of encrypted password username
user name Shane attributes
VPN-group-policy Payback_VPN
type of remote access service
username, encrypted James TdYPv1pvld/hPM0d password
user name James attributes
VPN-group-policy Payback_VPN
type of remote access service
Mark yruxpddqfyNb.qFn of encrypted password username
user name brand attributes
type of service admin
username password of Mary XND5FTEiyu1L1zFD encrypted
user name Mary attributes
VPN-group-policy Payback_VPN
type of remote access service
Massimo vs65MMo4rM0l4rVu encrypted password privilege 0 username
Massimo username attributes
VPN-group-policy Payback_VPN
type of remote access service
type tunnel-group Payback_VPN remote access
attributes global-tunnel-group Payback_VPN
VPN1 address pool
Group Policy - by default-Payback_VPN
IPSec-attributes tunnel-group Payback_VPN
IKEv1 pre-shared-key *.
tunnel-group 84.39.233.50 type ipsec-l2l
tunnel-group 84.39.233.50 General-attributes
Group - default policy - GroupPolicy_84.39.233.50
IPSec-attributes tunnel-group 84.39.233.50
IKEv1 pre-shared-key *.
remote control-IKEv2 pre-shared-key authentication *.
pre-shared-key authentication local IKEv2 *.
!
Global class-card class
match default-inspection-traffic
!
!
World-Policy policy-map
Global category
inspect the dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
Review the ip options
inspect the netbios
inspect the pptp
inspect the rsh
inspect the rtsp
inspect the sip
inspect the snmp
inspect sqlnet
inspect sunrpc
inspect the tftp
inspect xdmcp
inspect the icmp error
inspect the icmp
!
service-policy-international policy global
192.168.20.21 SMTP server
context of prompt hostname
no remote anonymous reporting call
call-home
Profile of CiscoTAC-1
no active account
http https://tools.cisco.com/its/service/oddce/services/DDCEService destination address
email address of destination [email protected] / * /
destination-mode http transport
Subscribe to alert-group diagnosis
Subscribe to alert-group environment
Subscribe to alert-group monthly periodic inventory
monthly periodicals to subscribe to alert-group configuration
daily periodic subscribe to alert-group telemetry
Cryptochecksum:d06974501eb0327a5ed229c8445f4fe1ASA 2
ASA Version 9.0 (1)
!
Payback-CIX hostname
activate the encrypted password of HSMurh79NVmatjY0
2KFQnbNIdI.2KYOU encrypted passwd
names of
!
interface Ethernet0/0
switchport access vlan 2
Speed 100
full duplex
!
interface Ethernet0/1
Description this port connects to the local network VIRTUAL 100
switchport access vlan 100
!
interface Ethernet0/2
!
interface Ethernet0/3
switchport access vlan 100
!
interface Ethernet0/4
switchport access vlan 100
!
interface Ethernet0/5
switchport access vlan 100
!
interface Ethernet0/6
switchport access vlan 100
!
interface Ethernet0/7
switchport access vlan 100
!
interface Vlan2
nameif outside
security-level 0
IP 84.39.233.50 255.255.255.240
!
interface Vlan100
nameif inside
security-level 100
IP 192.168.100.1 address 255.255.255.0
!
banner welcome to Payback loyalty - CIX connection line
passive FTP mode
summer time clock gmt/idt recurring last Sun Mar 01:00 last Sun Oct 02:00
DNS domain-lookup outside
DNS lookup field inside
DNS server-group defaultDNS
Name-Server 8.8.8.8
Server name 8.8.4.4
permit same-security-traffic inter-interface
network obj_any object
subnet 0.0.0.0 0.0.0.0
network of the host-CIX-1 object
host 192.168.100.2
Description This is the VM server host machine
network object host-External_CIX-1
Home 84.39.233.51
Description This is the external IP address of the server the server VM host
service object RDP
source between 1-65535 destination eq 3389 tcp service
network of the Payback_Office object
Home 92.51.193.158
service object MSQL
destination eq 1433 tcp service
network of the Development_OLTP object
Home 192.168.100.10
Description for Eiresoft VM
network of the External_Development_OLTP object
Home 84.39.233.52
Description This is the external IP address for the virtual machine for Eiresoft
network of the Eiresoft object
Home 146.66.160.70
Contractor s/n description
network of the External_TMC_Web object
Home 84.39.233.53
Description Public address to the TMC Web server
network of the TMC_Webserver object
Home 192.168.100.19
Internal description address TMC Webserver
network of the External_TMC_OLTP object
Home 84.39.233.54
External targets OLTP IP description
network of the TMC_OLTP object
Home 192.168.100.18
description of the interal target IP address
network of the External_OLTP_Failover object
Home 84.39.233.55
IP failover of the OLTP Public description
network of the OLTP_Failover object
Home 192.168.100.60
Server failover OLTP description
network of the servers object
subnet 192.168.20.0 255.255.255.0
being Wired network
192.168.10.0 subnet 255.255.255.0
the subject wireless network
192.168.40.0 subnet 255.255.255.0
network of the NETWORK_OBJ_192.168.100.0_24 object
255.255.255.0 subnet 192.168.100.0
network of the NETWORK_OBJ_192.168.10.0_24 object
192.168.10.0 subnet 255.255.255.0
network of the Eiresoft_2nd object
Home 137.117.217.29
Description 2nd Eiresoft IP
network of the Dev_Test_Webserver object
Home 192.168.100.12
Description address internal to the Test Server Web Dev
network of the External_Dev_Test_Webserver object
Home 84.39.233.56
Description This is the PB Dev Test Webserver
network of the NETWORK_OBJ_192.168.1.0_24 object
subnet 192.168.1.0 255.255.255.0
object-group service DM_INLINE_SERVICE_1
service-object MSQL
service-object RDP
object-group service DM_INLINE_SERVICE_2
service-object MSQL
service-object RDP
object-group service DM_INLINE_SERVICE_3
service-object MSQL
service-object RDP
object-group service DM_INLINE_SERVICE_4
service-object MSQL
service-object RDP
the tcp destination eq ftp service object
object-group service DM_INLINE_SERVICE_5
service-object MSQL
service-object RDP
the tcp destination eq ftp service object
object-group service DM_INLINE_SERVICE_6
service-object MSQL
service-object RDP
the Payback_Intrernal object-group network
object-network servers
Wired network-object
wireless network object
object-group service DM_INLINE_SERVICE_7
service-object MSQL
service-object RDP
object-group service DM_INLINE_SERVICE_8
service-object MSQL
service-object RDP
object-group service DM_INLINE_SERVICE_9
service-object MSQL
service-object RDP
object-group service DM_INLINE_SERVICE_10
service-object MSQL
service-object RDP
the tcp destination eq ftp service object
object-group service DM_INLINE_SERVICE_11
service-object RDP
the tcp destination eq ftp service object
outside_access_in list extended access allow object-group DM_INLINE_SERVICE_1 object Payback_Office object CIX-host-1
Note to access list OLTP Development Office of recovery outside_access_in
outside_access_in list extended access allow DM_INLINE_SERVICE_2 object Payback_Office object Development_OLTP object-group
Comment from outside_access_in-access Eiresoft access list
outside_access_in list extended access allow DM_INLINE_SERVICE_3 object Eiresoft object Development_OLTP object-group
outside_access_in list extended access allow DM_INLINE_SERVICE_4 object Payback_Office object TMC_Webserver object-group
Note to outside_access_in access to OLTP for target recovery Office Access list
outside_access_in list extended access allow DM_INLINE_SERVICE_5 object Payback_Office object TMC_OLTP object-group
outside_access_in list extended access allow DM_INLINE_SERVICE_6 object Payback_Office object OLTP_Failover object-group
Note to outside_access_in access-list that's allowing access of the Eiresoft on the failover OLTP server
outside_access_in list extended access allow DM_INLINE_SERVICE_7 object Eiresoft object OLTP_Failover object-group
Comment from outside_access_in-access list access for the 2nd period of INVESTIGATION of Eiresoft
outside_access_in list extended access allow DM_INLINE_SERVICE_8 object Eiresoft_2nd object Development_OLTP object-group
Note to outside_access_in access from the 2nd IP Eiresoft access list
outside_access_in list extended access allow DM_INLINE_SERVICE_9 object Eiresoft_2nd object OLTP_Failover object-group
outside_access_in list extended access allow DM_INLINE_SERVICE_10 object Payback_Office object Dev_Test_Webserver object-group
outside_access_in list extended access allow DM_INLINE_SERVICE_11 object Payback_Office object External_TMC_OLTP object-group
outside_cryptomap to access extended list ip 192.168.100.0 allow 255.255.255.0 192.168.10.0 255.255.255.0
pager lines 24
Enable logging
asdm of logging of information
Outside 1500 MTU
Within 1500 MTU
ICMP unreachable rate-limit 1 burst-size 1
don't allow no asdm history
ARP timeout 14400
no permit-nonconnected arp
NAT (inside, outside) source Dynamics one interface
NAT (inside, outside) static source CIX-host-1 External_CIX-host-1
NAT (inside, outside) static source Development_OLTP External_Development_OLTP
NAT (inside, outside) static source TMC_Webserver External_TMC_Web
NAT (inside, outside) static source TMC_OLTP External_TMC_OLTP
NAT (inside, outside) static source OLTP_Failover External_OLTP_Failover
NAT (inside, outside) static source Dev_Test_Webserver External_Dev_Test_Webserver
NAT (inside, outside) static source NETWORK_OBJ_192.168.100.0_24 NETWORK_OBJ_192.168.100.0_24 NETWORK_OBJ_192.168.10.0_24 NETWORK_OBJ_192.168.10.0_24 non-proxy-arp-search of route static destination
NAT (inside, outside) static source NETWORK_OBJ_192.168.100.0_24 NETWORK_OBJ_192.168.100.0_24 NETWORK_OBJ_192.168.1.0_24 NETWORK_OBJ_192.168.1.0_24 non-proxy-arp-search of route static destination
Access-group outside_access_in in interface outside
Route outside 0.0.0.0 0.0.0.0 84.39.233.49 1
Timeout xlate 03:00
Pat-xlate timeout 0:00:30
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
Floating conn timeout 0:00:00
dynamic-access-policy-registration DfltAccessPolicy
identity of the user by default-domain LOCAL
the ssh LOCAL console AAA authentication
Enable http server
http 92.51.193.156 255.255.255.252 outside
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown warmstart of cold start
Crypto ipsec transform-set ikev1 ESP-AES-128-SHA aes - esp esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-esp - aes esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-AES-128-SHA-TRANS-aes - esp esp-sha-hmac
Crypto ipsec ikev1 transform-set ESP-AES-128-SHA-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-TRANS-aes - esp esp-md5-hmac
Crypto ipsec ikev1 transform-set ESP-AES-128-MD5-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-AES-192-SHA-TRANS esp-aes-192 esp-sha-hmac
Crypto ipsec ikev1 transform-set ESP-AES-192-SHA-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-AES-192-MD5-TRANS esp-aes-192 esp-md5-hmac
Crypto ipsec ikev1 transform-set ESP-AES-192-MD5-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-AES-256-SHA-TRANS esp-aes-256 esp-sha-hmac
Crypto ipsec ikev1 transform-set ESP-AES-256-SHA-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-AES-256-MD5-TRANS esp-aes-256 esp-md5-hmac
Crypto ipsec ikev1 transform-set ESP-AES-256-MD5-TRANS mode transit
Crypto ipsec transform-set ikev1 SHA-ESP-3DES esp-3des esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-3DES-MD5-esp-3des esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-3DES-SHA-TRANS esp-3des esp-sha-hmac
Crypto ipsec ikev1 transform-set ESP-3DES-SHA-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-3DES-MD5-TRANS esp-3des esp-md5-hmac
Crypto ipsec ikev1 transform-set ESP-3DES-MD5-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-DES-SHA esp - esp-sha-hmac
Crypto ipsec transform-set ikev1 esp ESP-DES-MD5-esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-DES-SHA-TRANS esp - esp-sha-hmac
Crypto ipsec ikev1 transform-set ESP-DES-SHA-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-DES-MD5-TRANS esp - esp-md5-hmac
Crypto ipsec ikev1 transform-set ESP-DES-MD5-TRANS mode transit
Crypto ipsec ikev2 ipsec-proposal OF
encryption protocol esp
Esp integrity sha - 1, md5 Protocol
Crypto ipsec ikev2 proposal ipsec 3DES
Esp 3des encryption protocol
Esp integrity sha - 1, md5 Protocol
Crypto ipsec ikev2 ipsec-proposal AES
Esp aes encryption protocol
Esp integrity sha - 1, md5 Protocol
Crypto ipsec ikev2 ipsec-proposal AES192
Protocol esp encryption aes-192
Esp integrity sha - 1, md5 Protocol
Crypto ipsec ikev2 AES256 ipsec-proposal
Protocol esp encryption aes-256
Esp integrity sha - 1, md5 Protocol
Crypto ipsec pmtu aging infinite - the security association
card crypto outside_map 1 match address outside_cryptomap
card crypto outside_map 1 set pfs
peer set card crypto outside_map 1 92.51.193.158
card crypto outside_map 1 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5
outside_map card crypto 1jeu ikev2 AES AES192 AES256 3DES ipsec-proposal
outside_map interface card crypto outside
trustpool crypto ca policy
IKEv2 crypto policy 1
aes-256 encryption
integrity sha
Group 2 of 5
FRP sha
second life 86400
IKEv2 crypto policy 10
aes-192 encryption
integrity sha
Group 2 of 5
FRP sha
second life 86400
IKEv2 crypto policy 20
aes encryption
integrity sha
Group 2 of 5
FRP sha
second life 86400
IKEv2 crypto policy 30
3des encryption
integrity sha
Group 2 of 5
FRP sha
second life 86400
IKEv2 crypto policy 40
the Encryption
integrity sha
Group 2 of 5
FRP sha
second life 86400
Crypto ikev2 allow outside
Crypto ikev1 allow outside
IKEv1 crypto policy 10
authentication crack
aes-256 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 20
authentication rsa - sig
aes-256 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 30
preshared authentication
aes-256 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 40
authentication crack
aes-192 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 50
authentication rsa - sig
aes-192 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 60
preshared authentication
aes-192 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 70
authentication crack
aes encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 80
authentication rsa - sig
aes encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 90
preshared authentication
aes encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 100
authentication crack
3des encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 110
authentication rsa - sig
3des encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 120
preshared authentication
3des encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 130
authentication crack
the Encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 140
authentication rsa - sig
the Encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 150
preshared authentication
the Encryption
sha hash
Group 2
life 86400
Telnet timeout 5
SSH 77.75.100.208 255.255.255.240 outside
SSH 92.51.193.156 255.255.255.252 outside
SSH timeout 5
Console timeout 0dhcpd outside auto_config
!
a basic threat threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
internal GroupPolicy_92.51.193.158 group strategy
attributes of Group Policy GroupPolicy_92.51.193.158
VPN-tunnel-Protocol ikev1, ikev2
username password 6e6Djaz3W/XH59zX gordon encrypted privilege 15
tunnel-group 92.51.193.158 type ipsec-l2l
tunnel-group 92.51.193.158 General-attributes
Group - default policy - GroupPolicy_92.51.193.158
IPSec-attributes tunnel-group 92.51.193.158
IKEv1 pre-shared-key *.
remote control-IKEv2 pre-shared-key authentication *.
pre-shared-key authentication local IKEv2 *.
!
class-map inspection_default
match default-inspection-traffic
!
!
type of policy-card inspect dns preset_dns_map
parameters
maximum message length automatic of customer
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the preset_dns_map dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
inspect the rsh
inspect the rtsp
inspect esmtp
inspect sqlnet
inspect the skinny
inspect sunrpc
inspect xdmcp
inspect the sip
inspect the netbios
inspect the tftp
Review the ip options
inspect the icmp
!
global service-policy global_policy
context of prompt hostname
no remote anonymous reporting call
Cryptochecksum:83b2069fa311e6037163ae74f9b2bec2
: endHello
There are some clear problems I see on a quick glance. These are not related to the actual VPN configuration but rather the NAT configurations.
All your configuration of NAT CLI format above are configured as manual NAT / double NAT in Section 1. This means that the appliance NAT configurations have been added to the same section of the NAT configurations and scheduling of the NAT inside this Section rules is the cause of the problem for the L2L VPN connection for some.
Here are a few suggestions on what to change
ASA1
Minimal changes
the object of the LAN network
192.168.10.0 subnet 255.255.255.0
being REMOTE-LAN network
255.255.255.0 subnet 192.168.100.0
NAT (inside, outside) 1 static source LAN LAN to static destination REMOTE - LAN LAN
no nat source (indoor, outdoor) public static NETWORK_OBJ_192.168.10.0_24 NETWORK_OBJ_192.168.10.0_24 NETWORK_OBJ_192.168.100.0_24 NETWORK_OBJ_192.168.100.0_24 non-proxy-arp-search of route static destination
That means foregoing is first of all create 'object' that contain the local LAN and remote LANs. Then, it creates a NAT0 rule and adds to the top rules NAT. (number 1). It is essentially of at least one of the problems preventing the VPN operation or traffic that cross.
Finally, we remove the old rule that generated the ASDM. It would do the same thing if it has been moved to the top, but I generally find the creation of the 'object' with descriptive names easier on the eyes in the long term.
Other suggestions
These changes are not necessary with regard to the VPN L2L. Here are some suggestions how to clean a part of NAT configurations.
PAT-SOURCE network object-group
source networks internal PAT Description
object-network 192.168.10.0 255.255.255.0
object-network 192.168.20.0 255.255.255.0
object-network 192.168.40.0 255.255.255.0
NAT interface (it is, outside) the after-service automatic PAT-SOURCE dynamic source
No source (indoor, outdoor) nat Dynamics one interface
no nat (wireless, outdoors) source Dynamics one interface
no nat (servers, outside) no matter what source dynamic interface
The above configuration creates a "object-group" that lists all internal networks that you have dynamic PAT configured so far. It then uses the ' object-group ' in a command unique 'nat' to manage the dynamic PAT for all internal networks (with the exception of printers who had nothing at first). Then we remove the old PAT dynamic configurations.
Contains the command "nat" "car after" because it moving this "nat" configuration to the bottom of the NAT rules. For this reason its less likely to cause problems in the future.
network of the SERVERS object
subnet 192.168.20.0 255.255.255.0
network of the VPN-POOL object
192.168.50.0 subnet 255.255.255.0
NAT (servers, external) 2 static static source of destination of SERVERS SERVERS VPN-VPN-POOL
no nat (servers, external) static source NETWORK_OBJ_192.168.20.0_24 NETWORK_OBJ_192.168.20.0_24 NETWORK_OBJ_192.168.50.0_24 NETWORK_OBJ_192.168.50.0_24 non-proxy-arp-search of route static destination
The above configuration is supposed to create a NAT0 configuration for traffic between the network and the pool of Client VPN server. To my knowledge the old configuration that remove us is not used because the traffic would have matched PAT rule dynamic server yet rather than this rule which is later in the NAT configurations and would not be addressed.
no nat source (indoor, outdoor) public static NETWORK_OBJ_192.168.10.0_24 NETWORK_OBJ_192.168.10.0_24 NETWORK_OBJ_192.168.1.0_24 NETWORK_OBJ_192.168.1.0_24 non-proxy-arp-search of route static destination
It seems to me that network 192.168.1.0/24 is not configured from anywhere in your network. Therefore, the above 'nat' configuration seems useless, can be deleted. If I missed something and its use in then of course do not remove it.
ASA2
Minimal changes
the object of the LAN network
255.255.255.0 subnet 192.168.100.0
being REMOTE-LAN network
192.168.10.0 subnet 255.255.255.0
NAT (inside, outside) 1 static source LAN LAN to static destination REMOTE - LAN LAN
no nat source (indoor, outdoor) public static NETWORK_OBJ_192.168.100.0_24 NETWORK_OBJ_192.168.100.0_24 NETWORK_OBJ_192.168.10.0_24 NETWORK_OBJ_192.168.10.0_24 non-proxy-arp-search of route static destination
That means foregoing is first of all create 'object' that contain the local LAN and remote LANs. Then, it creates a NAT0 rule and adds to the top rules NAT. (number 1). It is essentially of at least one of the problems preventing the VPN operation or traffic that cross.
Finally, we remove the old rule that generated the ASDM.
Other suggestions
PAT-SOURCE network object-group
object-network 192.168.100.0 255.255.255.0
NAT interface (it is, outside) the after-service automatic PAT-SOURCE dynamic source
No source (indoor, outdoor) nat Dynamics one interface
The above configuration is supposed to do the same thing with the other ASA. Although given that this network contains only a single subnet it cleans the "nat" configurations exist that much. But the order of the "nat" configurations is changed to avoid further problems with the NAT order.
no nat source (indoor, outdoor) public static NETWORK_OBJ_192.168.100.0_24 NETWORK_OBJ_192.168.100.0_24 NETWORK_OBJ_192.168.1.0_24 NETWORK_OBJ_192.168.1.0_24 non-proxy-arp-search of route static destination
It seems to me that network 192.168.1.0/24 is not configured from anywhere in your network. Therefore, the above 'nat' configuration seems useless, can be deleted. If I missed something and its use in then of course do not remove it.
I suggest trying the changes related to VPN L2L first NAT0 configurations and test traffic. So who gets the work of connectivity, then you could consider changing other NAT configurations. There are other things that could be changed also in what concerns THAT static NAT servers but that probably better left for another time.
Hope this makes any sense and has helped
Remember to mark a reply as the answer if it answered your question.
Feel free to ask more if necessary
-Jouni
-
Problem with remote access VPN on ASA 5505
I currently have a problem of an ASA 5505 configuration to connect via VPN remote access by using the Cisco VPN Client 5.0.07.0440 under Windows 8 Pro x 64. The VPN client will prompt you for the user name and password during the connection process, but fails soon after.
The VPN client connects is as follows:
---------------------------------------------------------------------------------------------------------------------------------------
Cisco Systems VPN Client Version 5.0.07.0440
Copyright (C) 1998-2010 Cisco Systems, Inc.. All rights reserved.
Customer type: Windows, Windows NT
Running: 6.2.9200
2 15:09:21.240 11/12/12 Sev = Info/4 CM / 0 x 63100002
Start the login process
3 15:09:21.287 11/12/12 Sev = Info/4 CM / 0 x 63100004
Establish a secure connection
4 15:09:21.287 11/12/12 Sev = Info/4 CM / 0 x 63100024
Attempt to connect with the server "*." **. ***. *** »
5 15:09:21.287 11/12/12 Sev = Info/6 IKE/0x6300003B
Try to establish a connection with *. **. ***. ***.
6 15:09:21.287 11/12/12 Sev = Info/4 IKE / 0 x 63000001
From IKE Phase 1 negotiation
7 15:09:21.303 11/12/12 Sev = Info/4 IKE / 0 x 63000013
SEND to > ISAKMP OAK AG (SA, KE, NO, ID, VID (Xauth), VID (dpd), VID (Frag), VID(Nat-T), VID (Unity)) to *. **. ***. ***
8 15:09:21.365 11/12/12 Sev = Info/6 GUI/0x63B00012
Attributes of the authentication request is 6: 00.
9 15:09:21.334 11/12/12 Sev = Info/5 IKE/0x6300002F
Received packet of ISAKMP: peer = *. **. ***. ***
10 15:09:21.334 11/12/12 Sev = Info/4 IKE / 0 x 63000014
RECEIVING< isakmp="" oak="" ag="" (sa,="" ke,="" non,="" id,="" hash,="" vid(unity),="" vid(xauth),="" vid(dpd),="" vid(nat-t),="" nat-d,="" nat-d,="" vid(frag),="" vid(?))="" from="">
11 15:09:21.334 11/12/12 Sev = Info/5 IKE / 0 x 63000001
Peer is a compatible peer Cisco-Unity
12 15:09:21.334 11/12/12 Sev = Info/5 IKE / 0 x 63000001
Peer supports XAUTH
13 15:09:21.334 11/12/12 Sev = Info/5 IKE / 0 x 63000001
Peer supports the DPD
14 15:09:21.334 11/12/12 Sev = Info/5 IKE / 0 x 63000001
Peer supports NAT - T
15 15:09:21.334 11/12/12 Sev = Info/5 IKE / 0 x 63000001
Peer supports fragmentation IKE payloads
16 15:09:21.334 11/12/12 Sev = Info/6 IKE / 0 x 63000001
IOS Vendor ID successful construction
17 15:09:21.334 11/12/12 Sev = Info/4 IKE / 0 x 63000013
SENDING > ISAKMP OAK AG * (HASH, NOTIFY: NAT - D, NAT - D, VID (?), STATUS_INITIAL_CONTACT, VID (Unity)) to *. **. ***. ***
18 15:09:21.334 11/12/12 Sev = Info/6 IKE / 0 x 63000055
Sent a keepalive on the IPSec Security Association
19 15:09:21.334 11/12/12 Sev = Info/4 IKE / 0 x 63000083
IKE port in use - Local Port = 0xFBCE, Remote Port = 0 x 1194
20 15:09:21.334 11/12/12 Sev = Info/5 IKE / 0 x 63000072
Automatic NAT detection status:
Remote endpoint is NOT behind a NAT device
This effect is behind a NAT device
21 15:09:21.334 11/12/12 Sev = Info/4 CM/0x6310000E
ITS established Phase 1. 1 crypto IKE Active SA, 0 IKE SA authenticated user in the system
22 15:09:21.365 11/12/12 Sev = Info/5 IKE/0x6300002F
Received packet of ISAKMP: peer = *. **. ***. ***
23 15:09:21.365 11/12/12 Sev = Info/4 IKE / 0 x 63000014
RECEIVING< isakmp="" oak="" trans="" *(hash,="" attr)="" from="">
24 15:09:21.365 11/12/12 Sev = Info/4 CM / 0 x 63100015
Launch application xAuth
25 15:09:21.474 11/12/12 Sev = Info/4 IPSEC / 0 x 63700008
IPSec driver started successfully
26 15:09:21.474 11/12/12 Sev = Info/4 IPSEC / 0 x 63700014
Remove all keys
27 15:09:27.319 11/12/12 Sev = Info/4 CM / 0 x 63100017
xAuth application returned
28 15:09:27.319 11/12/12 Sev = Info/4 IKE / 0 x 63000013
SEND to > ISAKMP OAK TRANS *(HASH, ATTR) to *. **. ***. ***
29 15:09:27.365 11/12/12 Sev = Info/5 IKE/0x6300002F
Received packet of ISAKMP: peer = *. **. ***. ***
30 15:09:27.365 11/12/12 Sev = Info/4 IKE / 0 x 63000014
RECEIVING< isakmp="" oak="" trans="" *(hash,="" attr)="" from="">
31 15:09:27.365 11/12/12 Sev = Info/4 IKE / 0 x 63000013
SEND to > ISAKMP OAK TRANS *(HASH, ATTR) to *. **. ***. ***
32 15:09:27.365 11/12/12 Sev = Info/4 CM/0x6310000E
ITS established Phase 1. 1 crypto IKE Active SA, 1 IKE SA authenticated user in the system
33 15:09:27.365 11/12/12 Sev = Info/5 IKE/0x6300005E
Customer address a request from firewall to hub
34 15:09:27.365 11/12/12 Sev = Info/4 IKE / 0 x 63000013
SEND to > ISAKMP OAK TRANS *(HASH, ATTR) to *. **. ***. ***
35 15:09:27.397 11/12/12 Sev = Info/5 IKE/0x6300002F
Received packet of ISAKMP: peer = *. **. ***. ***
36 15:09:27.397 11/12/12 Sev = Info/4 IKE / 0 x 63000014
RECEIVING< isakmp="" oak="" trans="" *(hash,="" attr)="" from="">
37 15:09:27.397 11/12/12 Sev = Info/5 IKE / 0 x 63000010
MODE_CFG_REPLY: Attribute = INTERNAL_IPV4_ADDRESS:, value = 192.168.2.70
38 15:09:27.397 11/12/12 Sev = Info/5 IKE / 0 x 63000010
MODE_CFG_REPLY: Attribute = INTERNAL_IPV4_NETMASK:, value = 255.255.255.0
39 15:09:27.397 11/12/12 Sev = Info/5 IKE / 0 x 63000010
MODE_CFG_REPLY: Attribute = INTERNAL_IPV4_DNS (1):, value = 192.168.2.1
40 15:09:27.397 11/12/12 Sev = Info/5 IKE / 0 x 63000010
MODE_CFG_REPLY: Attribute = INTERNAL_IPV4_DNS (2):, value = 8.8.8.8
41 15:09:27.397 11/12/12 Sev = Info/5 IKE/0x6300000D
MODE_CFG_REPLY: Attribute = MODECFG_UNITY_SAVEPWD:, value = 0x00000001
42 15:09:27.397 11/12/12 Sev = Info/5 IKE/0x6300000E
MODE_CFG_REPLY: Attribute = MODECFG_UNITY_DEFDOMAIN:, value = NCHCO
43 15:09:27.397 11/12/12 Sev = Info/5 IKE/0x6300000D
MODE_CFG_REPLY: Attribute = MODECFG_UNITY_PFS:, value = 0x00000000
44 15:09:27.397 11/12/12 Sev = Info/5 IKE/0x6300000E
MODE_CFG_REPLY: Attribute = APPLICATION_VERSION, value = Cisco Systems, Inc. ASA5505 Version 8.2 (5) built by manufacturers on Saturday, May 20, 11 16:00
45 15:09:27.397 11/12/12 Sev = Info/5 IKE/0x6300000D
MODE_CFG_REPLY: Attribute = MODECFG_UNITY_SMARTCARD_REMOVAL_DISCONNECT:, value = 0x00000001
46 15:09:27.397 11/12/12 Sev = Info/5 IKE/0x6300000D
MODE_CFG_REPLY: Attribute = received and by using the NAT - T port number, value = 0 x 00001194
47 15:09:27.397 11/12/12 Sev = Info/4 CM / 0 x 63100019
Data in mode Config received
48 15:09:27.412 11/12/12 Sev = Info/4 IKE / 0 x 63000056
Received a request from key driver: local IP = 192.168.2.70, GW IP = *. **. ***. remote IP address = 0.0.0.0
49 15:09:27.412 11/12/12 Sev = Info/4 IKE / 0 x 63000013
SEND to > ISAKMP OAK QM * (HASH, SA, NO, ID, ID) to *. **. ***. ***
50 15:09:27.444 11/12/12 Sev = Info/5 IKE/0x6300002F
Received packet of ISAKMP: peer = *. **. ***. ***
51 15:09:27.444 11/12/12 Sev = Info/4 IKE / 0 x 63000014
RECEIVING< isakmp="" oak="" info="" *(hash,="" notify:status_resp_lifetime)="" from="">
52 15:09:27.444 11/12/12 Sev = Info/5 IKE / 0 x 63000045
Answering MACHINE-LIFE notify has value of 86400 seconds
53 15:09:27.444 11/12/12 Sev = Info/5 IKE / 0 x 63000047
This SA was already alive for 6 seconds, setting expiration 86394 seconds now
54 15:09:27.459 11/12/12 Sev = Info/5 IKE/0x6300002F
Received packet of ISAKMP: peer = *. **. ***. ***
55 15:09:27.459 11/12/12 Sev = Info/4 IKE / 0 x 63000014
RECEIVING< isakmp="" oak="" info="" *(hash,="" notify:no_proposal_chosen)="" from="">
56 15:09:27.459 11/12/12 Sev = Info/4 IKE / 0 x 63000013
SEND to > ISAKMP OAK INFO *(HASH, DEL) to *. **. ***. ***
57 15:09:27.459 11/12/12 Sev = Info/4 IKE / 0 x 63000049
IPsec security association negotiation made scrapped, MsgID = CE99A8A8
58 15:09:27.459 11/12/12 Sev = Info/4 IKE / 0 x 63000017
Marking of IKE SA delete (I_Cookie = A3A341F1C7606AD5 R_Cookie = F1F403018625E924) reason = DEL_REASON_IKE_NEG_FAILED
59 15:09:27.459 11/12/12 Sev = Info/5 IKE/0x6300002F
Received packet of ISAKMP: peer = *. **. ***. ***
60 15:09:27.459 11/12/12 Sev = Info/4 IKE / 0 x 63000058
Received an ISAKMP for a SA message no assets, I_Cookie = A3A341F1C7606AD5 R_Cookie = F1F403018625E924
61 15:09:27.459 11/12/12 Sev = Info/4 IKE / 0 x 63000014
RECEIVING< isakmp="" oak="" info="" *(dropped)="" from="">
62 15:09:27.490 11/12/12 Sev = Info/4 IPSEC / 0 x 63700014
Remove all keys
63 15:09:30.475 11/12/12 Sev = Info/4 IKE/0x6300004B
IKE negotiation to throw HIS (I_Cookie = A3A341F1C7606AD5 R_Cookie = F1F403018625E924) reason = DEL_REASON_IKE_NEG_FAILED
64 15:09:30.475 11/12/12 Sev = Info/4 CM / 0 x 63100012
ITS phase 1 deleted before first Phase 2 SA is caused by "DEL_REASON_IKE_NEG_FAILED". Crypto 0 Active IKE SA, 0 IKE SA authenticated user in the system
65 15:09:30.475 11/12/12 Sev = Info/5 CM / 0 x 63100025
Initializing CVPNDrv
66 15:09:30.475 11/12/12 Sev = Info/6 CM / 0 x 63100046
Set indicator established tunnel to register to 0.
67 15:09:30.475 11/12/12 Sev = Info/4 IKE / 0 x 63000001
Signal received IKE to complete the VPN connection
68 15:09:30.475 11/12/12 Sev = Info/4 IPSEC / 0 x 63700014
Remove all keys
69 15:09:30.475 11/12/12 Sev = Info/4 IPSEC / 0 x 63700014
Remove all keys
70 15:09:30.475 11/12/12 Sev = Info/4 IPSEC / 0 x 63700014
Remove all keys
71 15:09:30.475 11/12/12 Sev = Info/4 IPSEC/0x6370000A
IPSec driver successfully stopped
---------------------------------------------------------------------------------------------------------------------------------------
The running configuration is the following (there is a VPN site-to-site set up as well at an another ASA 5505, but that works perfectly):
: Saved
:
ASA Version 8.2 (5)
!
hostname NCHCO
Select hTjwXz/V8EuTw9p9 of encrypted password
hTjwXz/V8EuTw9p9 of encrypted passwd
names of
description of NCHCO name 192.168.2.0 City offices
name 192.168.2.80 VPN_End
name 192.168.2.70 VPN_Start
!
interface Ethernet0/0
switchport access vlan 2
Speed 100
full duplex
!
interface Ethernet0/1
!
interface Ethernet0/2
!
interface Ethernet0/3
!
interface Ethernet0/4
!
interface Ethernet0/5
!
interface Ethernet0/6
!
interface Ethernet0/7
!
interface Vlan1
nameif inside
security-level 100
IP 192.168.2.1 255.255.255.0
!
interface Vlan2
nameif outside
security-level 0
IP address **. ***. 255.255.255.248
!
boot system Disk0: / asa825 - k8.bin
passive FTP mode
access extensive list ip NCHCO 255.255.255.0 outside_nat0_outbound allow 192.168.1.0 255.255.255.0
access extensive list ip NCHCO 255.255.255.0 inside_nat0_outbound allow 192.168.1.0 255.255.255.0
inside_nat0_outbound list of allowed ip extended access all 192.168.2.64 255.255.255.224
access extensive list ip NCHCO 255.255.255.0 outside_1_cryptomap allow 192.168.1.0 255.255.255.0
access extensive list ip NCHCO 255.255.255.0 outside_1_cryptomap_1 allow 192.168.1.0 255.255.255.0
Standard access list LAN_Access allow NCHCO 255.255.255.0
LAN_Access list standard access allowed 0.0.0.0 255.255.255.0
pager lines 24
Enable logging
asdm of logging of information
Within 1500 MTU
Outside 1500 MTU
mask of VPN_Pool VPN_Start VPN_End of local pool IP 255.255.255.0
ICMP unreachable rate-limit 1 burst-size 1
ASDM image disk0: / asdm - 645.bin
don't allow no asdm history
ARP timeout 14400
Global 1 interface (outside)
NAT (inside) 0-list of access inside_nat0_outbound
NAT (inside) 1 0.0.0.0 0.0.0.0
NAT (outside) 0-list of access outside_nat0_outbound
Route outside 0.0.0.0 0.0.0.0 74.219.208.49 1
Timeout xlate 03:00
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
Floating conn timeout 0:00:00
dynamic-access-policy-registration DfltAccessPolicy
network-acl outside_nat0_outbound
WebVPN
SVC request to enable default svc
Enable http server
http 192.168.1.0 255.255.255.0 inside
http *. **. ***. 255.255.255.255 outside
http 74.218.158.238 255.255.255.255 outside
http NCHCO 255.255.255.0 inside
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown cold start
Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac
Crypto ipsec transform-set ESP-AES-128-MD5-esp - aes esp-md5-hmac
Crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
Crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac
Crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac
Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac
Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac
Crypto ipsec transform-set esp-3des esp-sha-hmac l2tp-transform
Crypto ipsec transform-set l2tp-transformation mode transit
Crypto ipsec transform-set vpn-transform esp-aes-256 esp-sha-hmac
Crypto ipsec transform-set esp-3des esp-sha-hmac TRANS_ESP_3DES_SHA
Crypto ipsec transform-set transit mode TRANS_ESP_3DES_SHA
Crypto ipsec transform-set esp-3des esp-md5-hmac TRANS_ESP_3DES_MD5
Crypto ipsec transform-set transit mode TRANS_ESP_3DES_MD5
Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
life crypto ipsec security association seconds 28800
Crypto ipsec kilobytes of life - safety 4608000 association
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 pfs Group1 set
Crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 value transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5
crypto dynamic-map dyn-map 10 set pfs Group1
crypto dynamic-map dyn-map transform 10-set, vpn l2tp-transformation-transformation
dynamic-map encryption dyn-map 10 value reverse-road
Crypto-map dynamic outside_dyn_map 20 game of transformation-TRANS_ESP_3DES_MD5
card crypto outside_map 1 match address outside_1_cryptomap
card crypto outside_map 1 set pfs Group1
peer set card crypto outside_map 1 74.219.208.50
card crypto outside_map 1 set of transformation-ESP-3DES-SHA
map outside_map 20-isakmp ipsec crypto dynamic outside_dyn_map
outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP
outside_map interface card crypto outside
inside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP
inside crypto map inside_map interface
card crypto vpn-map 1 match address outside_1_cryptomap_1
card crypto vpn-card 1 set pfs Group1
set vpn-card crypto map peer 1 74.219.208.50
card crypto vpn-card 1 set of transformation-ESP-3DES-SHA
dynamic vpn-map 10 dyn-map ipsec isakmp crypto map
crypto isakmp identity address
crypto ISAKMP allow inside
crypto ISAKMP allow outside
crypto ISAKMP policy 10
preshared authentication
3des encryption
md5 hash
Group 2
life 86400
crypto ISAKMP policy 15
preshared authentication
aes-256 encryption
sha hash
Group 2
life 86400
crypto ISAKMP policy 35
preshared authentication
3des encryption
sha hash
Group 2
life 86400
crypto ISAKMP ipsec-over-tcp port 10000
enable client-implementation to date
Telnet 192.168.1.0 255.255.255.0 inside
Telnet NCHCO 255.255.255.0 inside
Telnet timeout 5
SSH 192.168.1.0 255.255.255.0 inside
SSH NCHCO 255.255.255.0 inside
SSH timeout 5
Console timeout 0
dhcpd address 192.168.2.150 - 192.168.2.225 inside
dhcpd dns 216.68.4.10 216.68.5.10 interface inside
lease interface 64000 dhcpd inside
!
a basic threat threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
WebVPN
internal DefaultRAGroup group strategy
attributes of Group Policy DefaultRAGroup
value of server DNS 192.168.2.1
Protocol-tunnel-VPN IPSec l2tp ipsec
nchco.local value by default-field
attributes of Group Policy DfltGrpPolicy
value of server DNS 192.168.2.1
Protocol-tunnel-VPN IPSec l2tp ipsec svc webvpn
allow password-storage
enable IPSec-udp
enable dhcp Intercept 255.255.255.0
the address value VPN_Pool pools
internal NCHVPN group policy
NCHVPN group policy attributes
value of 192.168.2.1 DNS Server 8.8.8.8
Protocol-tunnel-VPN IPSec l2tp ipsec
value by default-field NCHCO
admin LbMiJuAJjDaFb2uw encrypted privilege 15 password username
username privilege 15 encrypted password yB1lHEVmHZGj5C2Z 8njferg
username, encrypted NCHvpn99 QhZZtJfwbnowceB7 password
attributes global-tunnel-group DefaultRAGroup
address (inside) VPN_Pool pool
address pool VPN_Pool
authentication-server-group (inside) LOCAL
authentication-server-group (outside LOCAL)
LOCAL authority-server-group
authorization-server-group (inside) LOCAL
authorization-server-group (outside LOCAL)
Group Policy - by default-DefaultRAGroup
band-Kingdom
band-band
IPSec-attributes tunnel-group DefaultRAGroup
pre-shared key *.
NOCHECK Peer-id-validate
tunnel-group DefaultRAGroup ppp-attributes
No chap authentication
no authentication ms-chap-v1
ms-chap-v2 authentication
tunnel-group DefaultWEBVPNGroup ppp-attributes
PAP Authentication
ms-chap-v2 authentication
tunnel-group 74.219.208.50 type ipsec-l2l
IPSec-attributes tunnel-group 74.219.208.50
pre-shared key *.
type tunnel-group NCHVPN remote access
attributes global-tunnel-group NCHVPN
address pool VPN_Pool
Group Policy - by default-NCHVPN
IPSec-attributes tunnel-group NCHVPN
pre-shared key *.
!
class-map inspection_default
match default-inspection-traffic
!
!
type of policy-card inspect dns preset_dns_map
parameters
maximum message length automatic of customer
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the preset_dns_map dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
inspect the rsh
inspect the rtsp
inspect esmtp
inspect sqlnet
inspect the skinny
inspect sunrpc
inspect xdmcp
inspect the sip
inspect the netbios
inspect the tftp
Review the ip options
!
global service-policy global_policy
context of prompt hostname
no remote anonymous reporting call
Cryptochecksum:15852745977ff159ba808c4a4feb61fa
: end
ASDM image disk0: / asdm - 645.bin
ASDM VPN_Start 255.255.255.255 inside location
ASDM VPN_End 255.255.255.255 inside location
don't allow no asdm history
Anyone have any idea why this is happening?
Thank you!
Add, crypto dynamic-map outside_dyn_map 20 value reverse-road.
With respect,
Safwan
-
VPN between 878 router and ASA 5505
Hello world
I struggled for a few days now to get a VPN connection works.
The situation
Two offices needs to be connected to eachother with a VPN. The two parties have a WAN connection.
The tunnel between locations rises very well but the communication fails in almost any way.
The host cannot ping each other and also the inside of the router and ASA pings fail.
The only ping works is from inside Site2 to the inside interface of the router side 1 (192.168.1.100 to 192.168.0.250)
NAT works very well on both sites behind the router / asa.
I think I'm doing something wrong with the roads or access lists but after 7 days, many refills, restores, driving from one end of the State to the other to reset stupid moves break and resolder my cable from the console and things completely with default start for 10 times, I'm through, I honestly don't know where to look for more...
Tech Specs:
Site1: has a cable modem that gives a WAN IP with DHCP address
This modem connects to the Cisco 878 (Fastethernet0) router
The router acts as a DHCP server and NAT gateway for the office and offers vpn connectivity to the other office
Site2: has a cable-modem/router (Cisco 3925), which made the NAT, this modem/router gives an IP private class-C (192.168.178.x)
This modem/router connects to a Cisco ASA 5505 (Fastethernet0)
The ASA also server as a DHCP server and NAT gateway for the office and offers vpn connectivity to the other office.
Online, it looks like this:
Office 1--> Cisco878--> WAN Cloud<---cablemodemrouter><--- asa5505=""><--- office="">
IP address ranges:
Office 1
Network 192.168.0.0
Subnet mask 255.255.255.0
Gateway 192.168.0.250
IP WAN XXXX
Office 2
Network 192.168.1.0
Subnetmak 255.255.255.0
Gateway 192.168.1.1
IP WAN XXXX
On the location of office 2, there is a NAT between ASA and WAN router. between 192.168.178.x 255.255.255.0
The modemrouter is a Cisco 3925, on which IPSEC passthrough is enabled.
Configs:
Site 1:
CISCO 878 router
Site 2
ASA 5505
I hope someone has a chance to look through my config and tell me what I did wrong this week
Even if you can not help me but still read here: Thank YOU!
(As my problem has been resolved, I removed the configs of this post. If for any reason, you want to work for these devices configuration, please send me a PM)
Post edited by: taaa lijf - reason: problem solved, removed configs and stuff private for obvious reasons ;)
Hello
Ping client customer site 1 site2 and make sh crypto isakmp his and sh crypto ipsec his on the router.
If sh crypto isakmp gives QM_Idle and ping fails and you have no package in the HS cypto ipsec his and then do a debug crypto ipsec
If sh crypto isakmp gives MM_NoState can do a debug crypto isakmp
One note however, you should have ip addresses static at least on the side, initiating the tunnel, otherwise it will not work when ip address changes.
Kind regards.
Alain.
Maybe you are looking for
-
Error R6025 Runtime after connect you Vista - card Flash memory does not
HelloI am a newbie & would appreciate any advice. I get a runtime R6025 error message when I connect Windows Vista.When I click out of the box, then I get a message saying Toshiba Flash Cards not working do not. I cancel that and my laptop is ok exce
-
What will happen to the computers that are still using Windows XP?
Original title: Windows XP? So, what will happen to the computers that are still using windows xp? Say, my computer is too old to support something newer than XP
-
Under xp, mozilla firefox
-
cannot write files to a cd run this problem getting 2146697211 error
will not write files to cd and fix what it says error # 2146697211
-
The ADMA00 interface driver has a problem; No audio or the sound of the computer
* Original title: no sound in Windows 7 device of reading levels ok but no sound. problem ADMA00 driver interface has a problem. its supposed to be fixed. I have no sound