Cisco TelePresence MCU disconnects a session IP

Similar Questions

• Configuration of the firewall Cisco Telepresence MCU 5320

  Hi all.

  I searched all the documents of the MCU again, but I found nothing on the ports it uses.

  Help me

  HI Sandra.  The 5320 MCU is the same as 4500 MCU.

  Incoming ports

  • FTP - TCP:21 + transient (dynamic rather than fixed) used TCP ports for passive mode
  • HTTP - TCP:80
  • HTTPS - TCP:443
  • H.323 - TCP:1720 + ephemeral TCP ports for incoming calls
  • SNMP - UDP:161
  • Outgoing calls to H.323 involve ephemeral ports TCP connections TCP TCP:1720 and a certain number of ephemeral TCP ports
  • Outgoing SIP TCP calls involve connections between the TCP ephemeral ports and TCP:5060
  • Outgoing SIP TCP calls involve connections between the TCP ephemeral ports and TCP:5061
  • Outgoing interruptions SNMP are sent the ephemeral ports UDP Port 162
  • Media (including audio and video, FECC messages) are ephemeral ports from ephemeral ports UDP.
  • The products acquired Cisco TANDBERG/Codian and gateway series series Cisco TelePresence allocate the ephemeral ports between 49152 to 65535 *. It is possible to change the ports on which these products receive and establish connections. For example, by default the Codian products Cisco acquired listen port 1720 H.323 calls and connections to port 80 web browser, but these can be modified (go to network > Services).

  Keep in mind this MCU does not support the streaming or conference me and have either the GK aboard.  If these ports are listed.

  The link to the Article can be found here:

  http://www.Cisco.com/en/us/docs/Telepresence/infrastructure/articles/conferencing_products_conferenceme_ports_used_kb_3.shtml

  VR

  Patrick

• Extension of Cisco TelePresence Management Suite Analytics

  Hello - I have a few queries on Cisco TelePresence Management Suite Analytics Extension and wanted to get help on the same.

  A. Cisco active development on this product and/or have predefined routes for this platform? We have not quite

  hear updates during the liberation of UC SEVT 10.0 for this platform?

  B. what kind of support is available for this platform in a perspective of customization of the report?

  C. are there examples of SQL scripts that could be re-used to produce reports of the below type:

  • Video endpoint / use of rooms
  • Number of subscriptions too video session
  • Capacity Trending & forecasting for the use of a Port of MCU and increases endpoint.

  D. What are the technical limitations known from the point of view analytics platform? In other words, it does not imply that

  the analytical potential lies in the hands of developer and NOT the platform, taking into account its APIs?

  Thank you

  SG

  See this thread, message of Kjetil Rees (marked as a correct answer) in particular:

  https://supportforums.Cisco.com/message/3449977

  You aren't going to get an answer about the development plans and roadmaps here in a public forum, you will need to contact your Cisco representative for this kind of information.

  If you want something where all the work has been done for you, and that is customized to your specific needs, then you might want to consider looking at vAnalytics, http://vyopta.com/products/vanalytics of Vyopta, http://vyopta.com/

  No, I am not associated with Vyopta, however, we use one of their products.

  /Jens

  Please note the answers and score the questions as "answered" as appropriate.

• Driver of Cisco Telepresence - room LoopBack

  Hello world

  Is it possible to create a meeting room on Cisco Telepresence driver that will return the video to the appellant alone in the room? As the [email protected] / * / Cisco's Sip URI? (A kind of selfview room)

  Thanks for your help.

  It is possible to show only one participant connected to a MCU conference selfview, but not for telepresence Server conferences.  It comes without caring if the driver is involved or not.  The service provided by Cisco closure is obtained with the C40/60 endpoints where the audio and the video plays in a loop directly to the connected call (output HDMI to HDMI-in, output audio RCA audio-in RCA/RCA).

• Cisco 4205 MCU and 5320 waterfall or any other alternative?

  There are 2 ports of microcontrollers 5320 (4.5) and (4.4) 4205 offering documents multimedia 16 and 12. I need to work together as an mcu with 28 or ports available max. Can anyone describe how can I do this?

  http://www.Cisco.com/c/en/us/support/docs/conferencing/Telepresence-MCU-...

  It's that this article may be the solution to my problem?

  Hello

  In your case use MCU 5320 (MCU1) as master and will act as a gateway for the 4205 MCU (MCU2) since no feature of the H323 gateway configuration and no guard integrated for series 5300 MCU.

  Kind regards

  ACE

• Allowing endpoints make multi-point on Cisco 4505 MCU calls

  Hello

  I have a Cisco 4505 MCU and several endpoints.  Is there a way to allow that my end point called multipoint adhoc using MCU 4505?  For example, I would say that dial site1 using mcu, then dial site2 help mcu or call a group (site 1 and site1...) using mcu and it would know that it is supposed to use the 4505.

  Thank you

  Ravi

  Of course, you can configure (a few 100) static, meeting rooms, auto create conferences on the fly, based on a model or have the means put in place and there is even an on screen menu allows users to create or join conferences.

  Check out the example (page 37ff) Administrator's guide

  http://www.Cisco.com/en/us/docs/Telepresence/infrastructure/MCU/admin_guide/Cisco_TelePresence_MCU_4-4_Product_administration_guide.PDF

• "The remote computer has disconnected your session because of an error in the licensing protocol. Try to reconnect to the remote computer, or contact your server administrator. »

  Hello

  I received the following error message

  "The remote computer has disconnected your session because of an error in the licensing protocol. Try to reconnect to the remote computer, or contact your server administrator. »

  This happens when I try to log on my remote on the icon access log, I put on my computer at home so that I can get to work if I need to.  He worked for a few months after I bought my new laptop and software, but now suddenly it doesn't.  I talked to my guy TI in the work and they seem to think it's a common problem with "Vista Home Premium", I can do to change it so that I can use the remote access icon?

  Thanks in advance

  Hello
   
  Licensing protocol handles the communication of information on licenses between your computer and the remote computer. If there is an error in the licensing protocol, your computer may not be connected to the remote computer.
   
  To resolve this problem, restart the computer and try connecting to the remote computer. If you continue to receive this error message, contact the server administrator.
   
  This also occurs if one of the registry entries is corrupt. Try the following steps to resolve this problem.
  1. Click Start, type regedit and press to enter.
  2. on the window of the registry editor, navigate to Computer\HKEY_LOCAL_MACHINE\Software\Microsoft\MSLicensing
  3. right click MSLicensing, click on export and provide a file name for example RemoteKeyBackup and click on save to the desktop.
  4. right click on the HardwareID key and store under MSLicensing folder and click on delete.
  5 restart the computer for changes to take effect. Restarting the computer will create new keys.
   
  NOTE: If the problem persists, then you can take backup of the MSLicensing registry key and to load it on the computer of the problem, this will fix the problem.
   
  Visit this link for more information:
  http://TechNet.Microsoft.com/en-us/library/cc756826 (WS.10) .aspx
   
  Important: Incorrectly editing the registry can cause serious problems on the computer.
  Back up the registry: http://windows.microsoft.com/en-us/windows7/Back-up-the-registry
   
  Try the steps and check the result.
   
  Kind regards
  Syed
  Answers from Microsoft supports the engineer.

• Remote Desktop disconnected. The remote computer disconnected the session because of an error in the licensing protocol. Try to connect to the computer again.

  I understand there is a patch to 'fix' it, but I don't know how to access.  Can anyone help?   Thank you.

  Here is an article on this problem with a proposed solution - although it seems a bit risky.  I would create a point system restore and backup of the registry before trying. http://kjctech.net/2009/06/12/the-remote-computer-disconnected-the-session-because-of-an-error/.  The same answer is given by Microsoft here: http://support.microsoft.com/?kbid=187614.

  Here is an another artidle which includes essentially the same correction (although I didn't check closely to see if they were the same): http://www.techbuzz.in/how-to-fix-the-remote-computer-disconnected-the-session-because-of-an-error-in-the-licensing-protocol-in-windows-vista.php.

  The thing is, I can't find a clear answer, if this applies between two ordinary computers or between a server and a computer.  I hope that the solution works in both cases.  If this isn't the case, you can still use the system restore to go back to the old situation and we can try to find another solution.

  I hope this helps.  Keep me posted.

  Good luck!

  Lorien - MCSA/MCSE/network + / has + - if this post solves your problem, please click the 'Mark as answer' or 'Useful' button at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• Is any impact of a change of the password of the local user account on an instance of a content server Cisco TelePresence virtual computer?

  Hello

  I'm looking to see if there is an impact to change the password of the local user account on an instance of a content server Cisco TelePresence virtual machine?

  The software version is v6.2 build 4073.

  Thank you in advance,

  Robert

  I'll assume, you are referring to the administrator account, but it can be applied to any local account which is located on the TCS server itself.  It has no impact to change the password, unless you are using doesn't say account to connect to the server of TCS or web interface, it will not affect the application of TCS as most things such as external storage or clustering rely on domain accounts and not the local server.

• Cisco TelePresence Manager version 1.7 does support Windows Small Business Server 2008?

  Hello

  Is Microsoft Windows Small Business Server 2008 supported the Protocol LDAP, AD and MS Exchange server for Cisco TelePresence Manager version 1.7?

  Thank you

  AA

  Hello Ahmed - although this configuration "can work", Windows 2008 Small Business Server is not on the support list. This means that it has not been tested and it certifies to work with telepresence.

  To my knowledge, he's not on the roadmap for the future support however, I search and repost as soon as I have an answer for you.

  Kind regards

  -Andrew

  Sent by Cisco Support technique iPhone App

• Cisco TelePresence SX20 with laptop

  I use a Cisco TelePresence as autonomous SX20 endpoint configured with a public IP address (in Pakistan). I want to connect a portable computer (to Canada) to start video conferencing using the portable camera. Please advice me the software to install on the laptop so that I can start with my SX20 videoconferencing based on IP configured on my SX20.

  To understand kindly refer to the disposal of partner network.

  Please help me its urgent.

  Hello

  www.ciscojabbervideo.com

  BR Oleksandr

• Cisco telepresence sx20

  Dear support team,

  I want to know how to configure cisco telepresence sx20.

  any body can help pls...

  Configuration Cisco Telepresence Sx20 is not easy to do. I think below link will help you for configuration.

  http://www.Cisco.com/c/dam/en/us/TD/docs/Telepresence/endpoint/quick-set-SX20/TC5/administrator_guide/sx20_quickset_administrator_guide_tc51.PDF

• Cisco Telepresence SX20 and Touch 8 Configuration after paired

  Hello

  I successfully connected and combined the SX20 Cisco's Telepresence and Cisco Telepresence Touch 8. Before using the 8 key, we used the remote control instead. As a result, I have two questions about this.

  1. as far as I know, when I use the 8 key, the remote control cannot be used. Is it possible to use both of them?

  2. How can I change the background of my SX20 touch 8? Previously, the remote I can easily choose the background for my SX20. But after pairing with Touch 8, background in my SX20 become a blue large clock. I really want to have a different background but cannot find the way how to change.

  Any help would be appreciated.

  Thank you.

  Sincerely,

  Bagus Hanindhito

  After you connect the 8 Touch, you can still use the remote control, you will need to put on the SX20:

  SystemUnit MenuType experimental configuration: full

  I think that the standard background when using a touchscreen device is what you see, blue with large clock.  However, after the MenuType return in full which will give you the full OSD which is used with the remote and not that of the button, you may be able to change the background then.

• Is there a way to allow users to disconnect their sessions on a remote server to the RDP from their local machine?

  QWINSTA and other command line utilities are a bit too complicated for the end users, we of course do not disconnect the session hurt accidentally. In general, we only questions with sessions stuck to a few users who would be perfect if utilities command-line integrated for rdp sessions would allow to change username, but since they require a dynamic session id # I don't know how this could be scripted. Is there a tool available for Windows 7 clients on a Server 2008 RDP allowing them to disconnect from their own session if they are blocked? We have enrolled in different time zones who have to connect remotely in order to do their job and sometimes it is too early here for someone to be there to help.

  I found a http://www.ctrl-alt-del.com.au/ , but it says it is only for Server 2003 and I tried and got an error flashed too quickly to be read.

  Thanks for your time.

  Hello

  Welcome to the Microsoft community.

  I would recommend you to view the query on the TechNet Forum which, I am sure, will help you better.

  You can check the link to the request message.

  http://social.technet.Microsoft.com/forums/en-us/category/w7itpro

  Click on a question and post your question.

  Please write us if you have any further questions.

• Activation of presence on the web setting in cisco telepresence SX-20

  I have EDT cisco telepresence SX-20 devices, want to allow the web presence but the poster ' mistake: it will be changed setting OSD "guid .pls myself

  What setting exactly are you trying to change?