Cisco TOR <>VTRX R1-2401 switches

Hello

It may be OT in a PowerConnect forum but at least it's a switch...

It's my first modern exhibition switches Dell; but I played a little with Cisco kit.   Then, someone whose had more time on a VRTX me has received indications linking the module _switch_ of a VRTX to a Cisco TOR (C4948) switch?

The deployment is for ESXi (5.1) and requires several VLANS on the VRTX blades.  There are only half a dozen of VLAN involved so manual definition is not a big deal. Cisco C4948 requires 802. 1 q on the trunk of cisco-style connection to R1-2401.

Once that the ILO is the question of the internal port (in the face of the blade-server) configuration...

General or Trunk mode?

Extracts of any config?

DRM for pointers...

D

Hi Dave,.

Want to check in with you and see if you were able to get this working?

Thank you

Tags: Dell Switches

Similar Questions

  • LAPAC1750PRO &amp; Cisco 2960-S - LACP issues Switch

    Hello community,

    I currently have a layer 2 Cisco 2960-S switch. It has 48 port Gigabit Ethernet ports and 4 SFP ports. I have Setup 3 VLAN on the switch VLAN 10, 11, 255. VLAN 10 is for my home equipment, VLAN 11 for my Audio/video/server equipment and VLAN255 is my network of comments. It's all behind a normal router from D-Link 4 port every day. All correctly connected working processes.

    I have the LAPAC1750PRO access point, I went ahead and ran 2 Cat6 cables so I could take advantage of the link aggregation 802.3d of the Access Point. I configured the passage from what I can tell properly. The problem is that when I turn on the two links AP causes beating port and stop passing traffic. If I disable the second link (leaving the active primary link) everything is stable. Speed is decent on my laptop, and from my iPad, it's fantastic.

    Does anyone have experience using the Protocol LACP (link Aggreagtion 802.3d) with this Access Point? I really want to use this so I can get 2 Gbps throughput of this device to my other devices.

    I'll be happy to post my Cisco Configuration so if someone is paid enough in that as well.

    Thank you

    Jason

    Senior Network Engineer

    OK - I thought about it. He was not at all a problem with the switch or my setup. This is the problem...

    Here's the question – and how I fixed it.

    1 cisco switch - Configuration:

    !

    GigabitEthernet1/0/1 interface
    switchport access vlan 10
    switchport mode access
    spanning tree portfast
    channel-group mode 1 on

    !

    interface GigabitEthernet1/0/2
    switchport access vlan 10
    switchport mode access
    spanning tree portfast
    channel-group mode 1 on

    That's right - this force LACP on the unit and do not have to worry about negotiating/connections protocols.

    2. access point - if it is already configured - factory reset the unit. LACP must be enabled during active keybord with DHCP boot. After that you can configure it as you want.

    What I had to do so was by default the access point and let it be starting with LACP rebuild - I wonder if this is due to something in the firmware that, once the NIC is configured, they become hardcoded and do not change to different settings?

    Whatever it is - this problem is solved.

  • How to connect Cisco SG-300-10 L3 switch selector mode in Mode of L2 SG-300-20

    Ladies and gentlemen, please forgive me if you find my question too basic. But, I would really appreciate your help. I have two Cisco switches (SG-300-10 and SG-300-20) and I am struggling to connect with each other.

    Requirements: Switch Cisco SG-300-10 which is in needs of L3 mode to send the traffic of VLAN tagged to the switch Cisco SG-300-20, which is the mode of L2

    What I've done so now

    1 Cisco SG-300-10 (Mode L3) to the router directly connected and configured IP addresses, 192.168.0.21. The GVRP is configured for Port 5. Created the VLAN 1000 with interface IP (192.168.100.1) and configured the Port 5 trunk mode (1U, 1000 t)

    2 connected Cisco SG-300-20 (L2 Mode) to the router and set up the IP address management, 192.168.0.22. The GVRP is configured for Port 5. 1000 of VLANS created and configured the Port 5 trunk mode (1U, 1000 t)

    What does not work

    I can't access the address of management of the L2 (192.168.0.22) switch. Note that the L2 switch only on the uplink, which is to the L3 switch. Since the Port 5 also receives no marked traffic of VLAN1 (192.168.1.1), I'm assuming that he would receive the network management of VLAN1.

    Other Observations

    When I connect the cable between the two switches Port5, I expect to exchange information of VLAN, by documentation. But the lights flash at all.

    I tried other things

    I tried to connect Port 2 (1U) L3 Switch switch 2 L3 Port (1U). Yet, I can't access to the management of the L2 switch port. However, when I connect 2-Port L3 switch to my laptop, I get an IP address. That tells me that I have to solve the problem of management network pair before the switches.

    Hi Späti,

    I think the confusion is the use of the address IP address to you and how you manage your computer.

    VLAN 1 = 192.168.1.1

    VLAN 1000 = 192.168.0.21

    How I read that you connect layer 2 VLAN 1 on 192.168.0.21 switch to layer 3 of the same VLAN 1 interface to 192.168.1.1. It's confusing.

    So first thing to do is this - change layer 2 switch network 192.168.1.x IP and confirm management works on VLAN 1.

    If you want to layer 2 switch works on VLAN 1000, then you need to change the default VLAN 1000, then you can configure your uplink either as the way which you have 1u, 1000 t, or you can use 1000u.

    Your management VLAN on the layer 2 switch is VLAN 1 still unless you changed it (which did you not?)

    A next important thing for the layer 2 switch is going to be the default gateway. The switch of level 3, you need to specify the address IP of the VLAN 1000, which I think you did to 192.168.0.21/24. This 192.168.0.21 must be the default gateway for the layer 2 switch.

    Finally, the computer you connect to layer 3 switch, what that either VLAN that you choose to connect to (1 unidentified), you need to set the IP and default gateway appropriate. So if you're going to VLAN 1 then your computer is 192.168.1.x with gateway 192.168.1.1

    And for the comment extra, GVRP is a horrible Protocol and very pitiful, I don't recommend to use.

  • Inter vlan routing on a Cisco SF 300-24 port switch only no internet except when scanning with wireshark

    Hello

    I'm get inter vlan routing to work on a 300-24 ports switch DF.    I have a network of business existing on 192.168.111.0 and want to create a vlan on 192.168.1.1 which can talk to 192.168.111.0.    I activated the layer 3 routing on the switch through the console and also provided ip routing commands. I have the following VIRTUAL networks:

    Vlan1 - default 192.168.111.0

    VLAN2 - 192.168.1.0

    I turned on DNS and provided my two servers DNS 192.168.111.82 & 192.168.111.212.

    I updated the VLAN1 interface 192.168.111.217 and VLAN2 interface 192.168.1.1.

    The FE1 - FE15 ports are access ports and assigned to VLAN1 (unidentified)

    FE16 - FE24 ports are access ports and assigned to VLAN2 (unidentified)

    I put a default route for the switch to 0.0.0.0 0.0.0.0 192.168.111.254 (router Draytek 2600). I have connected a computer (A) at the port of VLAN1 FE3 and a computer (B) to VLAN2 FE16 port.   I put its IP address and computer default gateway has to 192.168.111.217 to 192.168.111.94.    I updated computer B default gateway 192.168.1.1 and 192.168.1.2 IP.

    Computer A has access to the Mdaemon Server files via the network grows but no internet (cannot ping google) and can ping computer B and RDP on computer B.

    Computer B can ping computer A and RDP on A computer but do not have access to the company network i.e. MDaemon, file server etc.   It can also access the internet.

    The console I can ping www.google.co.uk and all the ip addresses in the network of the company i.e. 192.168.111.82 (DNS server).   I do not understand what I am doing wrong and have been banging my head for staretd a few days a new job and desperately need to work so any help would be greatly appreciated

    If I have computer scanner a wireshark wirh internet starts working wheird!

    Show the configuration below:

    switch7c0a71 #show run

    database of VLAN

    VLAN 2

    output

    Add a voice vlan Yes-table 0001e3 Siemens_AG_phone___

    Add a voice vlan Yes-table 00036 b Cisco_phone___

    Add a voice vlan Yes-table 00096e Avaya___

    Add a voice vlan Yes-table 000fe2 H3C_Aolynk___

    Add a voice vlan Yes-table 0060 b 9 Philips_and_NEC_AG_phone

    Add a voice vlan Yes-table 00d01e Pingtel_phone___

    VLAN voice Yes-table add Polycom/Veritel_phone___ 00e075

    Add a voice vlan Yes-table 00e0bb 3Com_phone___

    interface vlan 2

    IP 192.168.1.1 255.255.255.0

    output

    interface vlan 1

    IP 192.168.111.217 255.255.255.0

    output

    IP route 0.0.0.0 0.0.0.0 192.168.111.254

    interface vlan 1

    no ip address dhcp

    output

    Hello interface range vlan 1

    hostname switch7c0a71

    No complexity of passwords allow

    No server snmp Server

    interface fastethernet1

    switchport mode access

    output

    interface fastethernet2

    switchport mode access

    output

    interface fastethernet3

    switchport mode access

    output

    interface fastethernet4

    switchport mode access

    output

    interface fastethernet5

    switchport mode access

    output

    fastethernet6 interface

    switchport mode access

    output

    interface fastethernet7

    switchport mode access

    output

    interface fastethernet8

    switchport mode access

    output

    interface fastethernet9

    switchport mode access

    output

    interface fastethernet10

    switchport mode access

    output

    interface fastethernet11

    switchport mode access

    output

    interface fastethernet12

    switchport mode access

    output

    interface fastethernet13

    switchport mode access

    output

    interface fastethernet14

    switchport mode access

    output

    interface fastethernet15

    switchport mode access

    output

    interface fastethernet16

    switchport mode general

    VLAN allowed switchport General add 2 unidentified

    output

    interface fastethernet17

    switchport mode general

    VLAN allowed switchport General add 2 unidentified

    output

    interface fastethernet18

    switchport mode general

    VLAN allowed switchport General add 2 unidentified

    output

    interface fastethernet19

    switchport mode general

    VLAN allowed switchport General add 2 unidentified

    output

    interface fastethernet20

    switchport mode general

    VLAN allowed switchport General add 2 unidentified

    output

    interface fastethernet21

    switchport mode general

    VLAN allowed switchport General add 2 unidentified

    output

    interface fastethernet22

    switchport mode general

    VLAN allowed switchport General add 2 unidentified

    output

    interface fastethernet23

    switchport mode general

    VLAN allowed switchport General add 2 unidentified

    output

    interface fastethernet24

    switchport mode general

    VLAN allowed switchport General add 2 unidentified

    output

    interface vlan 2

    name of development

    output

    Hi Richard,

    43 - permit Protocol: any / all

    42 - Protocol deny EVERYTHING 192.168.2.0 0.0.0.255-> to 192.168.111.0 0.0.0.255

    41 - Protocol to deny ALL 192.168.111.0 0.0.0.255-> to 192.168.2.0 0.0.0.255

    40 allow the RDP Protocol TO ALL

    etc.

    To block everything, including MSSQL, with the exception of the RDP and other ports that you defined above.  The other defined are simply not the RDP Protocol and service work?

    Richard, do note useful messages and identify the right answers.

    Best,

    David

  • M8024 K-switch Cisco WS - 2960 S-24TD-L switch interconnection

    Hello

    I have 4 ports SFP + Module switch M8024-K. I want to establish connectivity 10Gig between M8024-k and Cisco WS-C2960S-24TD-L switch. I'm not able to find the exact Dell transmitter/receiver part number required for 4-port SFP + Module and cord Patch LC - LC-OFC required dell. I have no problem with Cisco parts.

    Kindly suggest exact reference numbers.

    Jean Marc

    This transceiver is listed on the list of compatibility of the server but not the switch. It can work in the switch, but I can't confirm that it will be because he is not on the compatibility list.

  • Switch Cisco Nexus 6004 removes more than 300 bytes IP packets

    Hi all

    We have a circuit of wave level 3 10 G running between two switches Cisco Nexus 6004. The circuit came online between our two data centers (in the same city) without problem.

    When attempting to ping to the remote-end 10G interface, it works very well with packets of 64 bytes. CDP is enabled and that we see the CDP information remote switch. However, if we increase the size of the ping to more than 300 bytes packets, we lose 1 in every 20.

    We settings MTU verifed, type of cable of 10G and duplex settings.

    Level 3A tested clean and we will move forward with more testing.

    Any ideas on the problem? We feel the carrier out and end to test with their testers. But so far, the circuit's own test. I was not sure if it is something related to Cisco. I am at a loss at the moment.

    Thank you.

    Mike

    Hi Mike,.

    There is nothing wrong with your switches or circuit.  NEXUS devices have a default COPP on the control plan that limit the size and the amount of traffic that must be the CPU process.

    http://www.Cisco.com/en/us/docs/switches/Datacenter/SW/6_x/NX-OS/security/configuration/guide/b_Cisco_Nexus_7000_NX-OS_Security_Configuration_Guide__Release_6.x_chapter_011001.html

    HTH

  • Configuration of SNMP on Cisco Small Business 300 Series managed switch

    Please can someone help me configure SNMP on Cisco Small Business 300 series switch?

    Thank you

    Hi Anton,.

    Don't forget to activate the service SNMP is first of all: Security > Services TCP/UDP.

    http://sbkb.Cisco.com/CiscoSB/UKP.aspx?VW=1&docid=3b13278d9ef9402a8fef57...

    also, you will find useful documents for configuration etc on our server community kb:

    http://sbkb.Cisco.com/CiscoSB/UKP.aspx?VW=1&docid=183cae2148d445b2a07473...

    Let us know if you have any problems.

    Aleksandra

  • How to configure the VLAN for Cisco SG500 - switch 28

    Hello

    First of all, it's my first post here, I hope that someone can help me and please be patient because I am very little known.

    OK, so let me explain to you the scénarion I face and I hope someone can help me.

    We have a Cisco SG500 - 28 port gigabit switch in our workplace.

    Our goal is to create 3 VLANs and separate networks between the various departments.

    Vlan1 (which is the default VLAN in the switch)-will be used for the COMPUTER service and management.

    VLAN100 - will be used for business.

    VLAN200 - will be used for clients who need to connect to internet via WiFi.

    I created VLAN100 and VLAN200, and VLAN1 is there by default.

    I want to use port 13 for VLAN200 and to connect the-Wifi access point there.

    The uplink is in port 25.

    I would be happy if you could explain things first to a more general, abstract level, and then we can look at the specific scenario that we have.

    SG500 Cisco - 28 Gets a Sophos UTM 9 router internet.

    I need to take care of the inter - VLAN routing so, subnet and DHCP

    Thanks in advance,

    Sincere greetings,

    D

    Hi Desmond, looking at this DHCP pool it looks correct.

    For the second part, you waant VLAN 200 only work on VLAN 200, that's fine. So if you have an access point, and everything on the VLAN 200 connects to the access point, you can make an access to this list. The access list is entered only, which means the inbound interface.

    So if you have a gateway connecting to #1 port. You'll need to build the access list and apply it to port number 1. That's assuming you make a list of access 'decline' subnet source IP of VLAN 200 destined for the other subnet, that you do not want access.

    The image on another post to fill out your reference numbers, then for the ACL link, it should be placed on the interface VLAN 200 first comes to the switch (IE, the port the access point connects, make sure that you choose to bind by port instead of per VLAN)

    -Tom
    Please mark replied messages useful
    http://blogs.Cisco.com/smallbusiness/

  • Required for NAC firewall ports manager manage/add the Cisco switch

    Hello

    I am trying to add switches cisco for the NAM, but I am not able to add the switch I get the error "unable to control switch" I tried opening ports 161-162 on the firwall; If I were to allow all traffic between the NAM and the switch, cisco NAM is able to add/manage the switch.

    Do not know what are the other ports may be required for cisco NAM for managing the switch?

    Thank you.

    Hello

    As far as I KNOW, only UDP 161 and 162 for SNMP communication ports must be open.

    Please make sure that you have configured the correct port on the switch:

    (config)# snmp-server host 172.16.1.61 traps version 2c cam_v2 udp-port 162 mac-notification snmp 

    If still does not, I would check the logs on the firewall for any traffic blocked between the cam and the switch.

    HTH,

    Tiago

    --

    If this helps you or answers to your question if it you please mark it as 'responded' or write it down, if other users can easily find it.

  • Cisco 6248 FI to Brocade 6510 SAN switch shows Link Down

    Hi all

    His new installation of Cisco UCS with Brocade SAN switch 6510.

    I followed the Cisco UCS to Brocade connectivity Guide.

    Even if the switch side so FI link is not coming. No lights are glowing.

    When I checked the switchshow @Brocade 6510, ports are No_Light status display. Where in other ports, it indicates the number of my storage device WWN.

    At the END, when I click on ports CF, its projection on all State - link down.

    Any who are facing this problem. ?

    Am I missing some configuration steps?

    Kind regards

    Praveen

    This should be a trivial or a very complex problem. I'd rather commonplace.

    Brocade is a CF 16 G switch; up to 8 G negotiation seems to work (storage subsystem).

    Maybe you could try to set the speed on the Brocade 8G port fix!

    Or something with the cables is wrong? Send / receive Crusaders?

    Are shortwave of the MMF SFP? cables connection as well?

    Connect cable from port for example. 31-33, 32 to 34 and see if it works?

  • Turn on the mtu on cisco switch and cisco user server

    Hi all

    someone got bad luck turning on the mtu on their cisco switch?  I guess I need to turn it on for all because the command is for all ports on cisco catalyst and my server switch is nearby to my user of switches and a broadband bandwidth 6 G or 6 ports, I need to turn it on for all user ports?

    Thanks for any comments, that you can add.

    I assume you mean Jumbo frame support! You shouldn't have any problems with that. Please take a look at for example http://www.cisco.com/en/US/products/hw/switches/ps700/products_configuration_example09186a008010edab.shtml for more details and the configuration of the different switches. According to the model, the parameters are for dedicated ports only or the entire switch. In the case of the switch everything you will need to reload (reboot) switch, so be careful.

    André

  • Compatibility of VLAN with Cisco

    Hello

    We just bought 10 x new Netgear switches (all M4100) to add to an existing Cisco infrastructure.

    Simple configuration with only 6 Valns.

    5: Admin, 30: VOIP, 101: management, 100: a set of Workstations, 102: second series of Workstations, 200: IPTV, 400: Internet, 401: Wireless Management

    All I wanted to do was: 2 last ports each switch netgear = T and all the VLANS. I have not identified all ports if I want to use in the appropriate vlan

    101 of VLAN is my Managementt Vlan. (Need to configure inter vlan routing for this to work)

    I only turned on three switches up to now and all three do not work. They work for a while and that packets but do not receive all.

    What I am doing wrong?

    What I need to get rid of the original vlan1 on the netgear?

    Is that what I need config in the STP to make these compatible with Cisco (300 and 400 series) switches.

    I use an optical backbone on Cisco and Netgear switches.

    Sincere greetings,

    OLAF

    Hi Moussa,.

    Thanks for reaching out.

    We got it working.

    Step 1: upgrade to the latest firmware.

    Step 2: Forget the MISTLETOE.

    We had a few questions about the old firmware - causing links to trunk have some incompatibility with their tag and removed the images between Cisco and Netgear brand.

    After the upgrade of the firmware that we had access to "switchport mode access" and "switchport mode trunk" orders fixing the access port and trunking issues.

    Thank you Mr President,

    OLAF

  • PoE for Cisco Catalyst 2960PD-8TT-L

    Hello

    Will deploy this device for a small office. Just a quick question, a Cisco Catalyst 2960PD-8TT-l switch provides PoE on all its 8 ports or simply powered through his PoE uplink port.

    Read the URL below, but did not have much info. TIA!

    http://www.Cisco.com/en/us/prod/collateral/switches/ps5718/ps6406/produc...

    Sent by Cisco Support technique iPhone App

    Sorry John, my comment is not directed at you.  The link you posted, the content is very, the lack of a better term, misleading.

    http://www.Cisco.com/en/us/products/ps12200/prod_models_comparison.html

    Go to this site instead.  It shows that the model you have chosen has NO PoE.  Instead, it uses the PoE of a switch upstream to turn.

  • Impossible to activate IPv6 on my 3560 switch

    Hi, I got a Cisco WS-C3560-24PS-E switch today and I can't activate IPv6 on it. I know that the command global so that it is "ipv6 unicast routing", but would not appear in the list of global order. Level 3 of Cisco Packet Tracer switch is the exact model as well as mine and I even used the same packet tracer IOS image and it didn't work ('ipv6 unicast routing' works on tracer package however). Even tried the upgrade to the LATEST IOS image and still nothing. Can someone please help? Is there something that I did?

    Switch #show version

    Software Cisco IOS, C3560 Software (C3560-IPSERVICESK9-M), Version 12.2 (55) SE6, RELEASE SOFTWARE (fc1)

    Technical support: http://www.cisco.com/techsupport

    Copyright (c) 1986-2012 by Cisco Systems, Inc.

    Updated Tuesday, July 23, 12 13:10 by prod_rel_team

    Image text-base: 0 x 01000000, database: 0x02F00000

    ROM: Bootstrap program is C3560 boot loader

    BOOTLDR: C3560 Boot Loader (C3560-HBOOT-M), Version 12.2 (44) SE5, RELEASE SOFTWARE (fc1)

    The availability of switch is 1 minute

    System to regain the power ROM

    System image file is "flash:/c3560-ipservicesk9-mz.122-55.SE6.bin".

    This product contains cryptographic features and is under the United States

    States and local laws governing the import, export, transfer and

    use. Delivery of Cisco cryptographic products does not imply

    third party approval to import, export, distribute or use encryption.

    Importers, exporters, distributors and users are responsible for

    compliance with U.S. laws and local countries. By using this product you

    agree to comply with the regulations and laws in force. If you are unable

    to satisfy the United States and local laws, return the product.

    A summary of U.S. laws governing Cisco cryptographic products to:

    http://www.Cisco.com/WWL/export/crypto/tool/stqrg.html

    If you need assistance please contact us by mail at

    [email protected] / * /.

    processor of WS-C3560-24PS (PowerPC405) Cisco (revision Q0) with K 131072 bytes of memory.

    Card processor ID CAT1124ZHE7

    Last reset of tension

    1 virtual Ethernet interface

    24 FastEthernet interfaces

    2 gigabit Ethernet interfaces

    Password recovery mechanism is activated.

    512K bytes of memory simulated by flash not volatile configuration.

    Basic Ethernet MAC address: 00:1: B0:15:06:00

    Number of the motherboard: 73-9673-09

    Power supply part number: 341-0029-05

    Motherboard serial number: CAT11235JLK

    Power supply serial number: DTN112241YW

    Revision number of the model: Q0

    Motherboard revision number: B0

    Model number: WS-C3560-24PS-E

    System serial number: CAT1124ZHE7

    Top Assembly part number: 800-26380-04

    Top of page revision number of the Assembly: D0

    Version ID: V06

    CLEI Code number: COM1100ARC

    Revision number of hardware consulting: 0x01

    SW Version SW Image model switch ports

    ------ ----- -----              ----------            ----------

    * 1 26 WS-C3560-24PS 12.2 SE6 (55) C3560-IPSERVICESK9-M

    Configuration register is 0xF

    Switch #show flash

    Directory of flash: /.

    2 - rwx 12752912 1 March 1993 00:06:44 + 00:00 c3560-ipservicesk9 - mz.122 - 55.SE6.bin

    3 - rwx 1048 1 Mar 1993 00:01:04 + 00:00 multiple-fs

    total 15998976 bytes (3243008 bytes free)

    Switch (config) #ip?

    Intellectual property

    Switch (config) #ipv?

    % Unrecognized command

    Hi Patrick

    You have configured sdm to ipv6 support

    Otherwise you can configure using below command

    SDM prefer double by default

    http://www.Cisco.com/en/us/docs/switches/LAN/catalyst3560/software/release/12.2_52_se/configuration/guide/swipv6.html

    Thank you

    Riadh

  • Cisco Catalyst 6509 and 6513 goes into config race disk0: / Backup Script

    We use a Cisco Catalyst 6509 and 6513 switches in our network LAN and Man.

    Please help me and share the script to take backup of all respective running to their disk0 configuration switches: / per week.

    Double post.

Maybe you are looking for

  • HP Probook 430 G1: Common validity of fingerprint driver for Windows 10

    Hello It is a solution. You will be able to use your fingerprint across Windows Hello without any HP software reader (I have not even try to use simplepass). I'm on Windows 10. Download and install: http://support.Lenovo.com/in/Hi/downloads/ds103635

  • Cannot change the album sides

    In iTunes 120.3.2.35 that seems to no longer be able to change the sides of the album.  The automatic classification of iTunes appear (which is good), but I can't change them, or if I can change the albums with no side.

  • No sound after installing Windows XP Home on my Satellite L500-EQ

    Hello I ' am Sorin from Romania and I have a problem with the audio driver on my Satellite L500-1EQ.I download the driver and do not work the sound.I have a message with an error.I tried several versions for this driver, but nothing happened. Can you

  • Why is-Web application server on a target at a distance in real time is not start?

    Hi, I need help urgent please I was wondering why the Web application server on a target at a distance in real time is not start? The target is 9014 real-time and its connected to a local network abroad, I have a public IP address port forwarded to t

  • The mouse does not says "there is no driver for this mouse.

    Original title: Retractable Belkin Mini travel mouse All of a sudden my mouse has stop working.  It is said that there is no driver for this mouse.  I used it for about a year.  There isn't any software mouse in particular.  I don't know what could h