Cisco VPN Client connected, but no secure way.

Similar Questions

• PIX: Cisco VPN Client connects but no routing

  Hello

  We have a Cisco PIX 515 with software 7.1 (2). He accepts Cisco VPN Client connections with no problems, but no routing does to internal networks directly connected to the PIX. For example, my PC is affected by the IP 172.16.2.57 and then ping does not respond to internal Windows server 172.16.0.12 or trying to RDP. The most irritating thing is that these attempts are recorded in the system log, but always ended with "SYN timeout", as follows:

  2009-01-06 23:23:01 Local4.Info 217.15.42.214% 302013-6-PIX: built 3315917 for incoming TCP connections (172.16.2.57/1283) outside:172.16.2.57/1283 inside: ALAI2 / 3389 (ALAI2/3389)

  2009-01-06 23:23:31 Local4.Info 217.15.42.214% 302014-6-PIX: TCP connection disassembly 3315917 for outside:172.16.2.57/1283 inside: ALAI2 / 3389 duration 0:00:30 bytes 0 SYN Timeout

  2009-01-06 23:23:31 Local4.Debug 217.15.42.214% 7-PIX-609002: duration of disassembly-outside local host: 172.16.2.57 0:00:30

  We tried to activate and deactivate "nat-control", "permit same-security-traffic inter-interface" and "permit same-security-traffic intra-interface", but the results are the same: the VPN connection is successfully established, but remote clients cannot reach the internal servers.

  I enclose the training concerned in order to understand the problem:

  interface Ethernet0

  Speed 100

  full duplex

  nameif outside

  security-level 0

  IP address xx.yy.zz.tt 255.255.255.240

  !

  interface Ethernet1

  nameif inside

  security-level 100

  172.16.0.1 IP address 255.255.255.0

  !

  access extensive list ip 172.16.0.0 inside_nat0_outbound allow 255.255.255.0 172.16.2.56 255.255.255.248

  !

  access extensive list ip 172.16.0.0 outside_cryptomap_dyn_20 allow 255.255.255.0 172.16.2.56 255.255.255.248

  !

  VPN_client_group_splitTunnelAcl list standard access allowed 172.16.0.0 255.255.255.0

  !

  IP local pool pool_vpn_clientes 172.16.2.57 - 172.16.2.62 mask 255.255.255.248

  !

  NAT-control

  Global xx.yy.zz.tt 12 (outside)

  NAT (inside) 0-list of access inside_nat0_outbound

  NAT (inside) 12 172.16.0.12 255.255.255.255

  !

  internal VPN_clientes group strategy

  attributes of Group Policy VPN_clientes

  xxyyzz.NET value by default-field

  internal VPN_client_group group strategy

  attributes of Group Policy VPN_client_group

  Split-tunnel-policy tunnelspecified

  value of Split-tunnel-network-list VPN_client_group_splitTunnelAcl

  xxyyzz.local value by default-field

  !

  I join all the details of the cryptographic algorithms because the VPN is successfully completed, as I said at the beginning. In addition, routing tables are irrelevant in my opinion, because the inaccessible hosts are directly connected to the internal LAN of the PIX 515.

  Thank you very much.

  can you confirm asa have NAT traversal allow otherwise, activate it in asa and vpn clients try again.

  PIX / ASA 7.1 and earlier versions

  PIX (config) #isakmp nat-traversal 20

  PIX / ASA 7.2 (1) and later versions

  PIX (config) #crypto isakmp nat-traversal 20

• Cisco ASA 8.4 (3) remote access VPN - client connects but cannot access inside the network

  I have problems to access the resources within the network when connecting with the Cisco VPN client for a version of 8.4 (3) operation of the IOS Cisco ASA 5510. I tried all new NAT 8.4 orders but cannot access the network interior. I can see traffic in newspapers when ping. I can only assume I have NAT evil or it's because the inside interface of the ASA is on the 24th of the same subnet as the network interior? Please see config below, any suggestion would be appreciated. I configured a VPN site to another in this same 5510 and it works well

  Thank you

  interface Ethernet0/0

  Speed 100

  full duplex

  nameif outside

  security-level 0

  IP x.x.x.x 255.255.255.240

  !

  interface Ethernet0/1

  Speed 100

  full duplex

  nameif inside

  security-level 100

  IP 10.88.10.254 255.255.255.0

  !

  interface Management0/0

  Shutdown

  nameif management

  security-level 0

  no ip address

  !

  permit same-security-traffic inter-interface

  permit same-security-traffic intra-interface

  network of the PAT_to_Outside_ClassA object

  10.88.0.0 subnet 255.255.0.0

  network of the PAT_to_Outside_ClassB object

  subnet 172.16.0.0 255.240.0.0

  network of the PAT_to_Outside_ClassC object

  Subnet 192.168.0.0 255.255.240.0

  network of the LocalNetwork object

  10.88.0.0 subnet 255.255.0.0

  network of the RemoteNetwork1 object

  Subnet 192.168.0.0 255.255.0.0

  network of the RemoteNetwork2 object

  172.16.10.0 subnet 255.255.255.0

  network of the RemoteNetwork3 object

  10.86.0.0 subnet 255.255.0.0

  network of the RemoteNetwork4 object

  10.250.1.0 subnet 255.255.255.0

  network of the NatExempt object

  10.88.10.0 subnet 255.255.255.0

  the Site_to_SiteVPN1 object-group network

  object-network 192.168.4.0 255.255.254.0

  object-network 172.16.10.0 255.255.255.0

  object-network 10.0.0.0 255.0.0.0

  outside_access_in deny ip extended access list a whole

  inside_access_in of access allowed any ip an extended list

  11 extended access-list allow ip 10.250.1.0 255.255.255.0 any

  outside_1_cryptomap to access extended list ip 10.88.0.0 255.255.0.0 allow object-group Site_to_SiteVPN1

  mask 10.250.1.1 - 10.250.1.254 255.255.255.0 IP local pool Admin_Pool

  NAT static NatExempt NatExempt of the source (indoor, outdoor)

  NAT (inside, outside) static source any any static destination RemoteNetwork4 RemoteNetwork4-route search

  NAT static LocalNetwork LocalNetwork destination (indoor, outdoor) static source RemoteNetwork1 RemoteNetwork1

  NAT static LocalNetwork LocalNetwork destination (indoor, outdoor) static source RemoteNetwork2 RemoteNetwork2

  NAT static LocalNetwork LocalNetwork destination (indoor, outdoor) static source RemoteNetwork3 RemoteNetwork3

  NAT (inside, outside) static source LocalNetwork LocalNetwork static destination RemoteNetwork4 RemoteNetwork4-route search

  !

  network of the PAT_to_Outside_ClassA object

  NAT dynamic interface (indoor, outdoor)

  network of the PAT_to_Outside_ClassB object

  NAT dynamic interface (indoor, outdoor)

  network of the PAT_to_Outside_ClassC object

  NAT dynamic interface (indoor, outdoor)

  Access-group outside_access_in in interface outside

  inside_access_in access to the interface inside group

  Route outside 0.0.0.0 0.0.0.0 x.x.x.x 1

  dynamic-access-policy-registration DfltAccessPolicy

  Sysopt connection timewait

  Service resetoutside

  Crypto ipsec transform-set ikev1 ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac

  Crypto ipsec transform-set ikev1 ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac

  Crypto ipsec transform-set ikev1 ESP-AES-192-SHA esp-aes-192 esp-sha-hmac

  Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-esp - aes esp-md5-hmac

  Crypto ipsec transform-set esp-ikev1 esp-md5-hmac bh-series

  Crypto ipsec transform-set ikev1 esp ESP-DES-MD5-esp-md5-hmac

  Crypto ipsec transform-set ikev1 ESP-3DES-MD5-esp-3des esp-md5-hmac

  Crypto ipsec transform-set ikev1 ESP-DES-SHA esp - esp-sha-hmac

  Crypto ipsec transform-set ikev1 ESP-AES-128-SHA aes - esp esp-sha-hmac

  Crypto ipsec transform-set ikev1 ESP-AES-256-SHA esp-aes-256 esp-sha-hmac

  Crypto ipsec transform-set ikev1 SHA-ESP-3DES esp-3des esp-sha-hmac

  Crypto-map dynamic dynmap 10 set pfs

  Crypto-map dynamic dynmap 10 set transform-set bh - set ikev1

  life together - the association of security crypto dynamic-map dynmap 10 28800 seconds

  Crypto-map dynamic dynmap 10 kilobytes of life together - the association of safety 4608000

  Crypto-map dynamic dynmap 10 the value reverse-road

  card crypto mymap 1 match address outside_1_cryptomap

  card crypto mymap 1 set counterpart x.x.x.x

  card crypto mymap 1 set transform-set ESP-AES-256-SHA ikev1

  card crypto mymap 86400 seconds, 1 lifetime of security association set

  map mymap 1 set security-association life crypto kilobytes 4608000

  map mymap 100-isakmp ipsec crypto dynamic dynmap

  mymap outside crypto map interface

  crypto isakmp identity address

  Crypto isakmp nat-traversal 30

  Crypto ikev1 allow outside

  IKEv1 crypto ipsec-over-tcp port 10000

  IKEv1 crypto policy 5

  preshared authentication

  3des encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 10

  preshared authentication

  3des encryption

  sha hash

  Group 1

  life 86400

  IKEv1 crypto policy 50

  preshared authentication

  the Encryption

  md5 hash

  Group 2

  life 86400

  IKEv1 crypto policy 60

  preshared authentication

  aes-256 encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 70

  preshared authentication

  aes-256 encryption

  sha hash

  Group 1

  life 86400

  IKEv1 crypto policy 90

  preshared authentication

  aes encryption

  sha hash

  Group 2

  life 86400

  Telnet timeout 5

  Console timeout 0

  management-access inside

  a basic threat threat detection

  Statistics-list of access threat detection

  no statistical threat detection tcp-interception

  WebVPN

  internal BACKDOORVPN group policy

  BACKDOORVPN group policy attributes

  value of VPN-filter 11

  Ikev1 VPN-tunnel-Protocol

  Split-tunnel-policy tunnelall

  BH.UK value by default-field

  type tunnel-group BACKDOORVPN remote access

  attributes global-tunnel-group BACKDOORVPN

  address pool Admin_Pool

  Group Policy - by default-BACKDOORVPN

  IPSec-attributes tunnel-group BACKDOORVPN

  IKEv1 pre-shared-key *.

  tunnel-group x.x.x.x type ipsec-l2l

  tunnel-group ipsec-attributes x.x.x.x

  IKEv1 pre-shared-key *.

  !

  class-map inspection_default

  match default-inspection-traffic

  !

  !

  type of policy-card inspect dns preset_dns_map

  parameters

  maximum message length automatic of customer

  message-length maximum 512

  Policy-map global_policy

  class inspection_default

  inspect the preset_dns_map dns

  inspect the ftp

  inspect h323 h225

  inspect the h323 ras

  inspect the rsh

  inspect the rtsp

  inspect esmtp

  inspect sqlnet

  inspect the skinny

  inspect sunrpc

  inspect xdmcp

  inspect the sip

  inspect the netbios

  inspect the tftp

  Review the ip options

  !

  global service-policy global_policy

  Excellent.

  Evaluate the useful ticket.

  Thank you

  Rizwan James

• VPN client connected but no ping nor access to privat network

  Hello

  I have a 1802w installed, a VPN client that can connect to the router and L2L connection, which works very well.

  On the router, I see that the client is connected, but no traffic passes. In sh crypto ipsec, I see that traffic is decrypted, but no packtets are encypted.

  Can someone point me in the right direction? I have the confs and debugs attached. Thanks for the help in advance.

  Erich

  Erich,

  Looking at your configuration, two things:

  1 - is the current running configuration. I see your Tunnel L2L is configured with an address of correspondence of 101, but I don't see a 101 ACL set on the router.

  2. your Split Tunnel must be reconfigured. Which means, the source and destination must be exchanged.

  SplitList extended IP access list

  permit ip 192.168.2.0 0.0.0.255 192.168.111.0 0.0.0.255

  Split Tunneling

  http://www.Cisco.com/en/us/Tech/tk59/technologies_configuration_example09186a00800a393b.shtml#Con4

  Also, the IP address pool you assign to clients, ensure that they are not part of a LAN on your side. If so, you can then run in routing problems.

  Kind regards

  Arul

  * Please note all useful messages *.

• Linksys Cisco VPN Client connection drops

  I have a Linksys BEFVP41 V2. I have a PC running Windows XP SP2 with customer VPN Cisco 5.0.00.0340. I have a problem when I log in the VPN client with my employer network. It seems to be ok. No problem to do the job, hit their proxy server, etc.. All of a sudden, the connection drops. It seems to 'freeze' the network. No surfing, without PuTTY. Sometimes 5 minutes after the connection or 3 hours later. I have to disconnect the VPN connection, and then reconnect. What could be the problem? My MTU is set to 1432. The Windows Firewall has exceptions for ports 10000, 4500 and 62515. I have a network in place at 172.20.x.x... not the default or typical 10.x.x.x network. Firmware is 1.01.04 on the router.

  
  

• 8.3 (1) ASA Cisco VPN Client and IP Communicator - one-way communication

  Community salvation.

  I have a strange problem with my setup and I'm sure it's either some type of routing (or NAT) or just missing one rule allows traffic. But I'm now at a point where I would like to ask your help.

  I have a few users remote access that have the Cisco IP Communicator (CICC) application installed on their laptops. So:

  The VPN with CPIC user <> ASA Firewall <> router voice <> MAC <> IP phone

  The VPN works fine for all other traffic. The connection of basis for the IP Communicator works well. He get is connected to the CallManager, is shown as registered and you can even call an internal phone and also external phones. BUT: while you can hear the called party (if the phone internal) it does not work for the other direction. There is no sound from the remote/appellant.

  I already understood that it is also not possible to ping from the phone VPN to the internal subnet IP phone. While the VPN user can ping any other device in the network internal, he cannot do for Cisco IP phones. But if the VPN phone calls a phone no-internal (mobile...) - it works!

  My thought is that the call cannot be build up properly between the VPN phone and the internal phone.

  I found similar situations with google, but they are all for the reverse: call for internal works, but not for VPN.

  What do you think?

  Hello

  Usually ASA lists specific to the customer networks VPN Split Tunnel runs.

  This would mean that there is a Split Tunnel ACL used in configurations of the SAA for this VPN connection that needs to have the missing network added to the VPN connection traffic.

  -Jouni

• Allow Cisco VPN Client through the firewall?

  Hello

  How can I allow a cisco VPN client work from the inside of our network to an external IP address?

  We have customers who wish to make use of their Cisco VPN Client companies but our ASA blocks I think?

  Also (sorry to ask) a friend in South America is having the same problem but I am not hink they use Cisco, is there a default port used by the client to Cisco? then I can send this info?

  Thank you

  Generally, the ASA will allow the IPSEC from the inside to outside traffic. This is when you want it came outside and connect to you - this is where it gets creative. You restrict outgoing traffic at all? You deny all ip/tcp/udp outgoing?

  But may depend on if the remote end is compaitable NAT - T, and if they have configured. Another question would be how they allow VPN traffic go?

• Cisco VPN Client anything cannot access through VPN on an ASA5505 8.4

  Hello

  Completely new to Cisco ASA and the need to get this working ASAP.

  8.4 (1) ASA 5505 is the secondary FW and I need to authorize all out and block everything coming, but for the VPN clients.  Since a jerk of Cisco, I used the ASDM and it's sorcerers to make this work, which may explain my situation.

  192.168.101.0/24 is the local network

  192.168.101.5 is the IP of ASA

  192.168.101.2 is the primary FW (and the default gateway for servers, I have to access through the VPN)

  10.10.101.0/24 is the VPN IP range (this can be what you want, I'm not married to it somehow)

  My Cisco VPN Client connects to the ASA and receives 10.10.101.1 IP address, but I get no connectivity to the ASA or any other 192.168.101.x or service server (tried RDP, telnet, ping, etc.)

  Configuration file is attached.

  Help pretty please!

  Thank you.

  Did you add a route for the VPN Pool on the main firewall to the ASA?

  Best regards

  Peer

  Sent by Cisco Support technique iPad App

• Receive message "Validation of C:\WINDOWS\System32\VSINIT.dll failure" error message when trying to run Cisco VPN Client.

  windows\system32\vsinit.dll

  I try to run CISCO "VPN Client" connect from my PC at home for my work PC.

  Then, I get a message:

  Validation failed for C:\WINDOWS\System32\VSINIT.dll

  Any ideas?

  Martin

  Hello

  Run the checker system files on the computer. Link, we can see: Description of Windows XP and Windows Server 2003 System File Checker (Sfc.exe): http://support.microsoft.com/kb/310747

  Note that: if he asks you the service pack CD, follow these steps from the link: you are prompted to insert a Windows XP SP2 CD when you try to run the tool on a Windows XP SP2 computer system File Checker: http://support.microsoft.com/kb/900910 (valid for Service pack 3)

  If the steps above is not enough of it please post your request in the TechNet forum for assistance: http://social.technet.microsoft.com/Forums/en/category/windowsxpitpro

• Cisco vpn client to connect but can not access to the internal network

  Hi all

  I have a VPN configured on cisco 5540. My vpn was working fine, but suddenly there is a question that the cisco vpn client to connect but can not access to the internal network

  Any help would be much appreciated.

  Hi Samir,

  I suggest that you go to the ASA and check the configuration to make sure that it complies with the requirements according to the reference below link:

  http://www.Cisco.com/en/us/products/ps6120/products_configuration_example09186a00805734ae.shtml

  (The link above includes split tunneling, but this is just an option.

  Please paste the output of "sh cry ipsec his" here so that we can check if phase 2 is properly trained. I would say as you go to IPSEC vpn client on your PC and check increment in packets sent and received in the window 'status '.

  Let me know if this can help,

  See you soon,.

  Christian V

• Problems to connect via the Cisco VPN client IPSec of for RV180W small business router

  Hello

  I tried to configure my router Cisco of RV180W as a customer VPN IPSec, but have encountered a problem that I hope someone can help me with. "" I managed to do the work of configuration so that the Cisco's VPN IPSec client authenticates successfully with the XAUTH user, I put on the router, but during the negotiation, the client ends with the following, which appears several times on the router error message: ' Mar 20 Oct 19:41:53 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [34360] has no config mode.

  I've read around the internet and a number of people seem to say that the Cisco VPN Client is not compatible with the router, but the same thing happens to my iPhone VPN client.

  Is it possible that this can be implemented? Below, I have attached the full configuration files and the log files. Thank you much in advance.

  Router log file (I changed the IP addresses > respectively as well as references to MAC addresses)

  Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: floating ports NAT - T with counterpart > [44074]
  Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] WARNING: notification to ignore INITIAL-CONTACT > [44074] because it is admitted only after the phase 1.
  Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: NAT - D payload does not match for > [4500]
  Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: NAT - D payload does not match for > [44074]
  Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: received unknown Vendor ID
  Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: received Vendor ID: CISCO-UNITY
  Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: NAT detected: is located behind a device. NAT and alsoPeer is behind a NAT device
  Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: request sending Xauth for > [44074]
  Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: ISAKMP Security Association established for > [4500] -> [44074] with spi =>.
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: receives the type of the attribute 'ISAKMP_CFG_REPLY' of > [44074]
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: login successful for the user "myusername".
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: myusername XAuthUser connected from the IP >
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: sending of information Exchange: Notify payload [10381]
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: receives the type of the attribute 'ISAKMP_CFG_REQUEST' of > [44074]
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] WARNING: ignored attribute 5
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] WARNING: attribute ignored 28683
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no mode config
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] WARNING: attribute ignored 28684
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no mode config
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: remove the invalid payload with doi:0.
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: purged-Association of ISAKMP security with proto_id = ISAKMP and spi =>.
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: myusername XAuthUser Logged Out of the IP >
  Mar 20 Oct 20:03:16 2015 (GMT + 0000): [r1] [IKE] INFO: ISAKMP Security Association deleted for > [4500] -> [44074] with spi =>

  The router configuration

  screen_shot_10-20 - 15_at_09.00_pm.png

  

  IKE policy

  screen_shot_10-20 - 15_at_09.00_pm_001.png

  

  screen_shot_10-20 - 15_at_09.01_pm.png

  

  VPN strategy

  screen_shot_10-20 - 15_at_09.02_pm.png

  

  screen_shot_10-20 - 15_at_09.02_pm_001.png

  

  Client configuration

  Hôte : < router="" ip=""> >

  Authentication group name: remote.com

  Password authentication of the Group: mysecretpassword

  Transport: Enable Transparent Tunneling; IPSec over UDP (NAT/PAT)

  Username: myusername

  Password: mypassword

  Please contact Cisco.

  Correct, the RV180 is not compatible with the Cisco VPN Client.  The Iphone uses the Cisco VPN Client.

  You can use the PPTP on the RV180 server to connect a PPTP Client.

  In addition, it RV180 will allow an IPsec connection to third-party customers 3.  Greenbow and Shrew Soft are 2 commonly used clients.

• Unable to connect via the Cisco VPN Client

  Hello

  I have configured remote access VPN to ASA and tries to connect via the Cisco VPN Client 5.0

  I am not able to connect and watch the journal on the SAA

  ASA-3-713902: Group = xxxxx, IP = x.x.x.x, withdrawal homologous peer table is placed, no match!

  ASA-4-713903: Group = xxxxx, IP x.x.x.x, error: impossible to rmeove PeerTblEntry

  ASA does not support the K9 i.e. VPN - DES is enabled and VPN-3DES-AES is disabled.

  What could be the reason.

  Concerning

  Hi, I had this same problem, here is the solution:

  When you perform a debug crypto isakmp 255, so you see that the cisco vpn client does not support SHA +, you must use MD5 + AN or sha with 3DES/AES.

  Be careful, this debugging is very talkative, but that's the only way I found to get ITS proposal on debugging.

  Well, change your strategy using MD5 isakmp / OF would do the trick.

• Cisco VPN Client 5.0.0 does not connect

  Hello

  I am trying to establish the VPN session the firewall to 5525 X Cisco ASA crossing 9.1.1 Cisco VPN Client. Although AnyConnect is the way to go, the inherited method must always be supported for some time as part of a migration. I tried two VPN users (authenticated by ad) on two client computers running Windows 7 64 bit and Cisco VPN Client 5.0.07.0440. Both users are able to establish a session to a computer at the ASA, but not the other. Entering credentails evil, the login popup will appear immediately. On the combination of username/password correct name, the following VPN client log messages are generated and the session drops that is "not connected" in the status bar. The PCF file is the same on both client computers.

  Cisco Systems VPN Client Version 5.0.07.0440
  Copyright (C) 1998-2010 Cisco Systems, Inc. All Rights Reserved.
  Client Type(s): Windows, WinNT
  Running on: 6.1.7601 Service Pack 1
  119    22:49:16.933  06/23/13  Sev=Info/6          IKE/0x6300003B
  Attempting to establish a connection with 203.99.111.44.
  120    22:49:16.939  06/23/13  Sev=Info/4          IKE/0x63000001
  Starting IKE Phase 1 Negotiation
  121    22:49:16.942  06/23/13  Sev=Info/4          IKE/0x63000013
  SENDING >>> ISAKMP OAK AG (SA, KE, NON, ID, VID(Xauth), VID(dpd), VID(Frag), VID(Nat-T), VID(Unity)) to 203.99.111.44
  122    22:49:16.973  06/23/13  Sev=Info/5          IKE/0x6300002F
  Received ISAKMP packet: peer = 203.99.111.44
  123    22:49:16.973  06/23/13  Sev=Info/4          IKE/0x63000014
  RECEIVING <<< ISAKMP OAK AG (SA, KE, NON, ID, HASH, VID(Unity), VID(Xauth), VID(dpd), VID(Nat-T), NAT-D, NAT-D, VID(Frag), VID(?)) from 203.99.111.44
  124    22:49:16.974  06/23/13  Sev=Info/5          IKE/0x63000001
  Peer is a Cisco-Unity compliant peer
  125    22:49:16.974  06/23/13  Sev=Info/5          IKE/0x63000001
  Peer supports XAUTH
  126    22:49:16.974  06/23/13  Sev=Info/5          IKE/0x63000001
  Peer supports DPD
  127    22:49:16.974  06/23/13  Sev=Info/5          IKE/0x63000001
  Peer supports NAT-T
  128    22:49:16.974  06/23/13  Sev=Info/5          IKE/0x63000001
  Peer supports IKE fragmentation payloads
  129    22:49:16.977  06/23/13  Sev=Info/6          IKE/0x63000001
  IOS Vendor ID Contruction successful
  130    22:49:16.977  06/23/13  Sev=Info/4          IKE/0x63000013
  SENDING >>> ISAKMP OAK AG *(HASH, NOTIFY:STATUS_INITIAL_CONTACT, NAT-D, NAT-D, VID(?), VID(Unity)) to 203.99.111.44
  131    22:49:16.977  06/23/13  Sev=Info/6          IKE/0x63000055
  Sent a keepalive on the IPSec SA
  132    22:49:16.977  06/23/13  Sev=Info/4          IKE/0x63000083
  IKE Port in use - Local Port =  0xCA7C, Remote Port = 0x1194
  133    22:49:16.977  06/23/13  Sev=Info/5          IKE/0x63000072
  Automatic NAT Detection Status:
  Remote end is NOT behind a NAT device
  This   end IS behind a NAT device
  134    22:49:17.000  06/23/13  Sev=Info/5          IKE/0x6300002F
  Received ISAKMP packet: peer = 203.99.111.44
  135    22:49:17.000  06/23/13  Sev=Info/4          IKE/0x63000014
  RECEIVING <<< ISAKMP OAK TRANS *(HASH, ATTR) from 203.99.111.44
  136    22:49:17.211  06/23/13  Sev=Info/4          IPSEC/0x63700008
  IPSec driver successfully started
  137    22:49:17.211  06/23/13  Sev=Info/4          IPSEC/0x63700014
  Deleted all keys
  138    22:49:23.207  06/23/13  Sev=Info/4          IKE/0x63000013
  SENDING >>> ISAKMP OAK TRANS *(HASH, ATTR) to 203.99.111.44
  139    22:49:23.393  06/23/13  Sev=Info/5          IKE/0x6300002F
  Received ISAKMP packet: peer = 203.99.111.44
  140    22:49:23.393  06/23/13  Sev=Info/4          IKE/0x63000014
  RECEIVING <<< ISAKMP OAK TRANS *(HASH, ATTR) from 203.99.111.44
  141    22:49:23.393  06/23/13  Sev=Info/4          IKE/0x63000013
  SENDING >>> ISAKMP OAK TRANS *(HASH, ATTR) to 203.99.111.44
  142    22:49:23.401  06/23/13  Sev=Info/5          IKE/0x6300005E
  Client sending a firewall request to concentrator
  143    22:49:23.401  06/23/13  Sev=Info/4          IKE/0x63000013
  SENDING >>> ISAKMP OAK TRANS *(HASH, ATTR) to 203.99.111.44
  144    22:49:23.427  06/23/13  Sev=Info/5          IKE/0x6300002F
  Received ISAKMP packet: peer = 203.99.111.44
  145    22:49:23.427  06/23/13  Sev=Info/4          IKE/0x63000014
  RECEIVING <<< ISAKMP OAK TRANS *(HASH, ATTR) from 203.99.111.44
  146    22:49:23.427  06/23/13  Sev=Info/5          IKE/0x63000010
  MODE_CFG_REPLY: Attribute = INTERNAL_IPV4_ADDRESS: , value = 10.2.193.69
  147    22:49:23.427  06/23/13  Sev=Info/5          IKE/0x63000010
  MODE_CFG_REPLY: Attribute = INTERNAL_IPV4_DNS(1): , value = 10.2.5.2
  148    22:49:23.428  06/23/13  Sev=Info/5          IKE/0x63000010
  MODE_CFG_REPLY: Attribute = INTERNAL_IPV4_DNS(2): , value = 10.1.5.2
  149    22:49:23.428  06/23/13  Sev=Info/5          IKE/0x6300000D
  MODE_CFG_REPLY: Attribute = MODECFG_UNITY_SAVEPWD: , value = 0x00000000
  150    22:49:23.428  06/23/13  Sev=Info/5          IKE/0x6300000D
  MODE_CFG_REPLY: Attribute = MODECFG_UNITY_SPLIT_INCLUDE (# of split_nets), value = 0x00000001
  151    22:49:23.428  06/23/13  Sev=Info/5          IKE/0x6300000F
  SPLIT_NET #1
  subnet = 10.0.0.0
  mask = 255.0.0.0
  protocol = 0
  src port = 0
  dest port=0
  152    22:49:23.428  06/23/13  Sev=Info/5          IKE/0x6300000E
  MODE_CFG_REPLY: Attribute = MODECFG_UNITY_DEFDOMAIN: , value = example.org
  153    22:49:23.428  06/23/13  Sev=Info/5          IKE/0x6300000D
  MODE_CFG_REPLY: Attribute = MODECFG_UNITY_PFS: , value = 0x00000000
  154    22:49:23.428  06/23/13  Sev=Info/5          IKE/0x6300000E
  MODE_CFG_REPLY: Attribute = APPLICATION_VERSION, value = Cisco Systems, Inc ASA5525 Version 9.1(1) built by builders on Wed 28-Nov-12 11:15 PST
  155    22:49:23.428  06/23/13  Sev=Info/5          IKE/0x6300000D
  MODE_CFG_REPLY: Attribute = MODECFG_UNITY_SMARTCARD_REMOVAL_DISCONNECT: , value = 0x00000001
  156    22:49:23.428  06/23/13  Sev=Info/5          IKE/0x6300000D
  MODE_CFG_REPLY: Attribute = Received and using NAT-T port number , value = 0x00001194
  157    22:49:23.445  06/23/13  Sev=Info/4          IKE/0x63000056
  Received a key request from Driver: Local IP = 10.2.193.69, GW IP = 203.99.111.44, Remote IP = 0.0.0.0
  158    22:49:23.445  06/23/13  Sev=Info/4          IKE/0x63000013
  SENDING >>> ISAKMP OAK QM *(HASH, SA, NON, ID, ID) to 203.99.111.44
  159    22:49:23.477  06/23/13  Sev=Info/5          IKE/0x6300002F
  Received ISAKMP packet: peer = 203.99.111.44
  160    22:49:23.477  06/23/13  Sev=Info/4          IKE/0x63000014
  RECEIVING <<< ISAKMP OAK INFO *(HASH, NOTIFY:STATUS_RESP_LIFETIME) from 203.99.111.44
  161    22:49:23.477  06/23/13  Sev=Info/5          IKE/0x63000045
  RESPONDER-LIFETIME notify has value of 86400 seconds
  162    22:49:23.477  06/23/13  Sev=Info/5          IKE/0x63000047
  This SA has already been alive for 7 seconds, setting expiry to 86393 seconds from now
  163    22:49:23.477  06/23/13  Sev=Info/5          IKE/0x6300002F
  Received ISAKMP packet: peer = 203.99.111.44
  164    22:49:23.477  06/23/13  Sev=Info/4          IKE/0x63000014
  RECEIVING <<< ISAKMP OAK INFO *(HASH, NOTIFY:NO_PROPOSAL_CHOSEN) from 203.99.111.44
  165    22:49:23.478  06/23/13  Sev=Info/4          IKE/0x63000013
  SENDING >>> ISAKMP OAK INFO *(HASH, DEL) to 203.99.111.44
  166    22:49:23.478  06/23/13  Sev=Info/4          IKE/0x63000049
  Discarding IPsec SA negotiation, MsgID=F3E3C530
  167    22:49:23.478  06/23/13  Sev=Info/4          IKE/0x63000017
  Marking IKE SA for deletion  (I_Cookie=CD65262E1C3808E4 R_Cookie=912AE160ADADEE65) reason = DEL_REASON_IKE_NEG_FAILED
  168    22:49:23.478  06/23/13  Sev=Info/5          IKE/0x6300002F
  Received ISAKMP packet: peer = 203.99.111.44
  169    22:49:23.479  06/23/13  Sev=Info/4          IKE/0x63000058
  Received an ISAKMP message for a non-active SA, I_Cookie=CD65262E1C3808E4 R_Cookie=912AE160ADADEE65
  170    22:49:23.479  06/23/13  Sev=Info/4          IKE/0x63000014
  RECEIVING <<< ISAKMP OAK INFO *(Dropped) from 203.99.111.44
  171    22:49:24.310  06/23/13  Sev=Info/4          IPSEC/0x63700014
  Deleted all keys
  172    22:49:26.838  06/23/13  Sev=Info/4          IKE/0x6300004B
  Discarding IKE SA negotiation (I_Cookie=CD65262E1C3808E4 R_Cookie=912AE160ADADEE65) reason = DEL_REASON_IKE_NEG_FAILED
  173    22:49:26.849  06/23/13  Sev=Info/4          IKE/0x63000001
  IKE received signal to terminate VPN connection
  174    22:49:26.855  06/23/13  Sev=Info/4          IPSEC/0x63700014
  Deleted all keys
  175    22:49:26.855  06/23/13  Sev=Info/4          IPSEC/0x63700014
  Deleted all keys
  176    22:49:26.855  06/23/13  Sev=Info/4          IPSEC/0x63700014
  Deleted all keys
  177    22:49:26.855  06/23/13  Sev=Info/4          IPSEC/0x6370000A
  IPSec driver successfully stopped
  

  Any ideas why the second client of Windows 7 does not work?

  Kind regards

  Rick.

  Rick

  Thanks for the additional output. It shows the xauth authentication step, which is good to see. But it does not offer much clarity on what is causing the problem.

  My attention is drawn to a couple of message on the balls that are in line with the two sessions for which you posted newspapers.

  32 00:36:08.178 24/06/13 Sev = Info/5 IKE/0x6300005E

  Customer address a request from firewall to hub

  I'm not sure that we see any answer to this, but it makes me wonder if it is somehow involved in the issue. Is it possible that there is a difference in the configuration of firewall and operating between two clients?

  I am also interested in this series of posts

  48 00:36:08.210 24/06/13 Sev = Info/4 IKE / 0 x 63000056

  Received a request from key driver: local IP = 10.2.193.69, GW IP = 203.99.111.44, Remote IP = 0.0.0.0

  I don't know why the pilot requested a key at this point, and I wonder why the remote IP is 0.0.0.0?

  It is followed by a package in which the ASA provides the value of the life of SA - which seems to be on the path to a successful connection. that is followed by

  55 00:36:08.350 24/06/13 Sev = Info/5 IKE/0x6300002F

  Received packet of ISAKMP: peer = 203.99.111.44

  56 00:36:08.350 24/06/13 Sev = Info/4 IKE / 0 x 63000014

  RECEIVING< isakmp="" oak="" info="" *(hash,="" notify:no_proposal_chosen)="" from="">

  during which the SAA indicates that no proposal has been selected. It seems therefore that the ASA is not happy about something.

  If we do not find indications of the client that allows to identify the problem, then maybe we look at the ASA. Are all log messages generated on the SAA during this attempt to establish VPN that could show us the problem? Would it not be possible to run debugs on the SAA in a trial of this machine?

  HTH

  Rick

• Unable to connect using the Cisco VPN client

  Hi all. I recently configured a 5510 ASA to allow remote access using the Cisco VPN client. The problem is that everything works fine when I connect using a modem classic or on a computer with a public address that I use for testing purposes, but whenever I try to connect with on an ADSL line, I can't access to the resources. I have connection and after that nothing, I can not achieve anything.

  I enclose the relevant configuration information in the attachment. Any help is welcome.

  Depending on the version, add...

  ISAKMP nat-traversal

  or

  ISAKMP nat-traversal crypto

  Should be all you need.

• connect Cisco VPN client v5 to asa 5505

  I have remote vpn configuration issues between ASA5505 and Cisco VPN client v5. Successfully, I can establish a connection between the client Vpn and ASA and receive the IP address of the ASA. Statistical customer VPN windows shows that packets are sent and encrypted but none of the packages is received/decrypted.

  Cannot ping asa 5505

  Any ideas on what I missed?

  Try adding...

  ISAKMP nat-traversal crypto

  In addition, you cannot ping the inside interface of the ASA vpn without this command...

  management-access inside

  Please evaluate the useful messages.