Cisco vpn client is supported on the analogue ppp connection
can someone pls tell me if we can use the client vpn cisco on a ppp connection analog and put a pix that is not PPPs running. If it works, then why do we need to VPN L2tp/ipsec. can someone pls tell me something abt it. It is very urgent.
concerning
Assane
Assane,
If I understand your question, you speak with PPP initially to get an IP address from your service provider, then use the Client VPN VPN in your Pix Firewall. If so, yes it is possible.
To name a few reasons why PPTP or L2TP/IPSEC is used instead of Cisco VPN Client are:
1. because companies have used a PPTP or L2TP/IPSEC solution for some time and are migrating to Cisco VPN
2. do not install vpn on the PC client software
3. won't pay for the VPN Client software licenses
Let me know if it helps.
Kind regards
Arul
Tags: Cisco Security
Similar Questions
-
Configure the Cisco VPN client to pass through the VPN site-to-site (GUI)
Hello
I say hat the chain and responses I've seen to achieve this goal have been great...
https://supportforums.Cisco.com/discussion/12234631/Cisco-ASA-5505-VPN-p...
and
https://supportforums.Cisco.com/document/12191196/AnyConnect-client-site...
My question is "we will get this configuration by using the graphical user interface for someone who is not notified about the command line?"
Thank you
Of course, all this can be configured via ASDM.
Looking at the second example you posted above, they point you first change:
ACL split of the tunnel for the AnyConnect customer
This Configuration > remote access VPN > network (Client) access > AnyConnect connection profile > (chose the profile and select Edit) > (choose "Manage" next to group policy) > Edit > advanced > Split Tunneling > ensure that the policy does not "Inherit" but rather "Tunnel network list below" > Unselect "Inherit" next to the network list, then 'manage '. Enter your networks you want in the GUI in this dialog box. Click OK all the way back to the main window ASDM and click on apply.
You then change:
Crypto ACL for the tunnel from Site to Site
To do this, go to Configuration > VPN Site-to_site > connection profiles > (choose your profile and select edit) > add the VPN client address pool to the list of local network between protect networks. Yet once, click OK all the way back to the main window ASDM and click on apply.
Then, allow the
ASA to redirect back on the same interface traffic it receives
.. is defined under Configuration > Device Setup > Interfaces. (check the box at the bottom of this screen). Click on apply
Finally, there is the NAT exemption. For which go to Configuration > firewall > rules NAT. Add a NAT device rule before rules network object with Interface Source out, Source address your address pool VPN, the Destination address to include remote subnets and Action is Static Source NAT type source address and destination address remaining as original (i.e. without NAT). Once on OK all the way back to the main window ASDM and click on apply. Save and test.
Good luck. Don't forget to note the brand and posts useful when your question is answered.
-
AAA ipsec vpn clients how to see the history of connection on asdm or asa5510
Hello all, I would like to know how see history of connection ipsec vpn client users, they authenticate to the local aaa, not in active directory. I am able to see the current logon session. go to monitoring\vpn\vpn statistics\sessions, this shows me sessions underway, but I would like to see for example the connections client vpn for the last month. I did some research and saw the info on aaa Server? I checked that article and does not see what I was looking for.
It's actually a called (NPS) network policy server microsoft radius server.
The one I used (ACS 5 and ACS 5) who was just an example.
You can review the below listed doc
http://fixingitpro.com/2009/09/08/using-Windows-Server-2008-as-a-RADIUS-server-for-a-Cisco-ASA/
Jatin kone
-Does the rate of useful messages-
-
Help, please! Microsoft Vs Cisco VPN Client VPN
Could someone please indicate if the Cisco VPN Client is safer than the VPN integrated Microsoft on windows XP? If the Cisco client is more secure than why? Microsoft it does not use IPSEC and PPTP right?
Please advise - very urgent!
I don't know a customer Cisco Cisco VPN concentrator is safer, but I'm not sure exactly why.
Carlton,
Take a deeper look at the same time, all your questions will be answered once you look at these links.
IPSec is a Cisco VPN standard, open customer or any customer VPN IPSec based should meet these standards. You'll learn more by reading these few bellow of links at the end of the reading you will be to have a better
perspective on the customer you would gear more to use as a professional network.
Personally, I've been away little by little PPTP and substituting Cisco VPN clients. Don't get me wrong, PPTP is still widely used there, but it is more vulnerable.
With Ipsec VPN, you have a wider choice of authentication algorithms, to base
granularity of ciphers as a way to implement a secure VPN extreamely for RA architecture
Introduction to IPsec
http://www.Cisco.com/en/us/Tech/tk583/TK372/technologies_tech_note09186a0080094203.shtml
Introduction to PPTP/L2TP
http://www.Clavister.com/manuals/ver8.6x/manual/VPN/pptp_basics.htm
Analysis of vulnerabilities and implementation MS PPTP
http://www.Schneier.com/paper-PPTP.html
http://www.Schneier.com/paper-PPTP.PDF
Alternative workaround to use client MS using L2TP over Ipsec
In addition, you can do a google search on "hacking PPTP" or "Ipsec" to preview more vulnerabilities.
Rgds
Jorge
-
Cisco VPN Client and Windows XP VPN Client IPSec to ASA
I configured ASA for IPSec VPN via Cisco VPN Client and XP VPN client communications. I can connect successfully with Cisco VPN Client, but I get an error when connecting with the XP client. Debugging said "misconfigured groups and transport/tunneling mode" I know, they use different methods of transport and tunneling, and I think that I have configured both. Take a look at the config.
PS a funny thing - when I connect with client VPN in Windows Server 2003, I have no error. The only difference is that client XP is behind an ADSL router and client server is directly connected to the Internet on one of its public IP of interfaces. NAT in the case of XP can cause problems?
Config is:
!
interface GigabitEthernet0/2.30
Description remote access
VLAN 30
nameif remote access
security-level 0
IP 85.*. *. 1 255.255.255.0
!
access-list 110 scope ip allow a whole
NAT list extended access permit tcp any host 10.254.17.10 eq ssh
NAT list extended access permit tcp any host 10.254.17.26 eq ssh
access-list extended ip allowed any one sheep
access list nat-ganja extended permit tcp any host 10.254.17.18 eq ssh
sheep-vpn access-list extended permits all ip 192.168.121.0 255.255.255.0
tunnel of splitting allowed access list standard 192.168.121.0 255.255.255.0
flow-export destination inside-Bct 192.168.1.27 9996
IP local pool raccess 192.168.121.60 - 192.168.121.120 mask 255.255.255.0
ARP timeout 14400
global (outside-Baku) 1 interface
global (outside-Ganja) interface 2
NAT (inside-Bct) 0 access-list sheep-vpn
NAT (inside-Bct) 1 access list nat
NAT (inside-Bct) 2-nat-ganja access list
Access-group rdp on interface outside-Ganja
!
Access remote 0.0.0.0 0.0.0.0 85.*. *. 1 2
Route outside Baku 10.254.17.24 255.255.255.248 10.254.17.10 1
Route outside Baku 192.1.1.0 255.255.255.0 10.254.17.10 1
Outside-Baku route 192.168.39.0 255.255.255.0 10.254.17.10 1
Route outside-Ganja 192.168.45.0 255.255.255.0 10.254.17.18 1
Route outside-Ganja 192.168.69.0 255.255.255.0 10.254.17.18 1
Route outside-Ganja 192.168.184.0 255.255.255.0 10.254.17.18 1
Route outside Baku 192.168.208.16 255.255.255.240 10.254.17.10 1
Route outside-Ganja 192.168.208.112 255.255.255.240 10.254.17.18 1
dynamic-access-policy-registration DfltAccessPolicy
Crypto ipsec transform-set esp-3des esp-md5-hmac RIGHT
Crypto ipsec transform-set newset aes - esp esp-md5-hmac
Crypto ipsec transform-set esp-3des esp-md5-hmac vpnclienttrans
Crypto ipsec transform-set vpnclienttrans transport mode
Crypto ipsec transform-set esp-3des esp-md5-hmac raccess
life crypto ipsec security association seconds 214748364
Crypto ipsec kilobytes of life security-association 214748364
raccess 1 set transform-set vpnclienttrans crypto dyn1 dynamic-map
vpnclientmap 30 card crypto ipsec-isakmp dynamic dyn1
card crypto interface for remote access vpnclientmap
crypto isakmp identity address
ISAKMP crypto enable vpntest
ISAKMP crypto enable outside-Baku
ISAKMP crypto enable outside-Ganja
crypto ISAKMP enable remote access
ISAKMP crypto enable Interior-Bct
crypto ISAKMP policy 30
preshared authentication
3des encryption
md5 hash
Group 2
life 86400
No encryption isakmp nat-traversal
No vpn-addr-assign aaa
Telnet timeout 5
SSH 192.168.1.0 255.255.255.192 outside Baku
SSH 10.254.17.26 255.255.255.255 outside Baku
SSH 10.254.17.18 255.255.255.255 outside Baku
SSH 10.254.17.10 255.255.255.255 outside Baku
SSH 10.254.17.26 255.255.255.255 outside-Ganja
SSH 10.254.17.18 255.255.255.255 outside-Ganja
SSH 10.254.17.10 255.255.255.255 outside-Ganja
SSH 192.168.1.0 255.255.255.192 Interior-Bct
internal vpn group policy
attributes of vpn group policy
value of DNS-server 192.168.1.3
Protocol-tunnel-VPN IPSec l2tp ipsec
Split-tunnel-policy tunnelspecified
Split-tunnel-network-list value split tunnel
BCT.AZ value by default-field
attributes global-tunnel-group DefaultRAGroup
raccess address pool
Group-RADIUS authentication server
Group Policy - by default-vpn
IPSec-attributes tunnel-group DefaultRAGroup
pre-shared-key *.
Hello
For the Cisco VPN client, you would need a tunnel-group name configured on the ASA with a pre-shared key.
Please see configuration below:
http://www.Cisco.com/en/us/products/ps6120/products_configuration_example09186a00805734ae.shtml
or
Please see the section of tunnel-group config of the SAA.
There is a tunnel-group called "rtptacvpn" and a pre-shared key associated with it. This group name is used by the VPN Client Group name.
So, you would need a specific tunnel-group name configured with a pre-shared key and use it on the Cisco VPN Client.
Secondly, because you are behind a router ADSL, I'm sure that's configured for NAT. can you please activate NAT - T on your ASA.
"crypto isakmp nat-traversal.
Thirdly, change the transformation of the value
raccess 1 set transform-set vpnclienttrans crypto dyn1 dynamic-map
Let me know the result.
Thank you
Gilbert
-
Cisco VPN client with internet
Hello
I have a big problem, we have implemented Cisco VPN client to connect to outside to our internal servers. My problem is that all users access to the internet while using the Cisco VPN client. We use the split tunneling, but still all VPN clients access the internet. An advisor to prevent access to the internet through VPN client.
Thank you
You said earlier that you allow split tunnel. Are you still doing that?
We would need to see all of the VPN configuration - including access lists or objects referenced - to provide comprehensive advice.
-
Slow initial connection using Cisco VPN Client
I am currently using Cisco VPN Client v5.0.07.0290. Whenever I start my connection, it takes me about 90 seconds for the prompt to display authentication and another ~ 90 seconds to finish the auth. and connect successfully. I have another computer laptop w / the same WIN7 OS and version of Cisco VPN Client and he ends the connection to<30 sec. ="" why="" is="" this? ="" any="" suggestions="">
Hi Sergio,
You import the .pcf for the VPN Client file? If so, please try to recreate a new file .pcf locally on the machine itself and try to connect. Let me know how it goes.
Thank you
Delvallée
-
Hello
I would like to know why when it failed to connect to the private network through the Cisco VPN client and trying to establish an Internet connection, the connection Internet.
Thanks in advance,
SK
Which would be configured on the vpn, firewall/router endpoint etc..
-
Cisco VPN Client and 64-Bit OS Support
I'm in the stages of planning/testing of migrating users to the Cisco VPN client. Problem that I came across well is that I can't find a version that supports 64-bit operating systems. I looked through the Download Center with no luck. I'm a little more looking for a version out there? Thanks in advance.
As much as I know there is no 64-bit support and is not yet on the roadmap of IPSEC VPN Client. For more details, see:
http://www.Cisco.com/en/us/docs/security/ASA/compatibility/ASA-VPN-compatibility.html
Concerning
Farrukh
-
Unable to connect via the Cisco VPN Client
Hello
I have configured remote access VPN to ASA and tries to connect via the Cisco VPN Client 5.0
I am not able to connect and watch the journal on the SAA
ASA-3-713902: Group = xxxxx, IP = x.x.x.x, withdrawal homologous peer table is placed, no match!
ASA-4-713903: Group = xxxxx, IP x.x.x.x, error: impossible to rmeove PeerTblEntry
ASA does not support the K9 i.e. VPN - DES is enabled and VPN-3DES-AES is disabled.
What could be the reason.
Concerning
Hi, I had this same problem, here is the solution:
When you perform a debug crypto isakmp 255, so you see that the cisco vpn client does not support SHA +, you must use MD5 + AN or sha with 3DES/AES.
Be careful, this debugging is very talkative, but that's the only way I found to get ITS proposal on debugging.
Well, change your strategy using MD5 isakmp / OF would do the trick.
-
How to allow access to a local area network behind the cisco vpn client
Hi, my question is about how to allow access to a local area network behind the cisco vpn client
With the help of:
- Cisco 5500 Series Adaptive Security Appliance (ASA) that is running version 8.2 software
- Cisco VPN Client version 5.0 software
Cisco VPN client allows to inject a local routes in the routing table Cisco ASA?
Thank you.
Hi Vladimir,.
Unfortunately this is not a supported feature if you connect through the VPN Client. With VPN Client, that the VPN Client can access the VPN Client LAN host/local machine, not host from the local network to business as customer VPN is not designed for access from the local company network, but to the local corporate network.
If you want to access from your local business to your LAN network, you need to configure LAN-to-LAN tunnel.
-
[SOLVED] Native Iphone4s Cisco VPN client cannot establish the tunnel (victory clients do)
Hello
IPhone 4 s last IOS5 V 5.1.1 installed
I'm not able to make the native IPSEC VPN connection upset my company Cisco 877
Instead, all my computer laptop and netbook with Cisco VPN Client work installed fine when they connect remotely to society 877
Turn debugging 877, it seems Iphone successfully passes the 1 connection ike (actually Iphone wonder phase2 user/pass), but it hung to phase2 give me the error 'Negotiation with the VPN server has no' back
An idea or a known issue on this?
This is how I configured my VPN 877 part:
R1 (config) # aaa new-model
R1 (config) # aaa authentication default local connection
R1 (config) # aaa authentication login vpn_xauth_ml_1 local
R1 (config) # aaa authentication login local sslvpn
R1 (config) # aaa authorization network vpn_group_ml_1 local
R1 (config) # aaa - the id of the joint session
Crypto isakmp policy of R1 (config) # 1
R1(config-ISAKMP) # BA 3des
# Preshared authentication R1(config-ISAKMP)
Group R1(config-ISAKMP) # 2
R1(config-ISAKMP) #.
R1(config-ISAKMP) #crypto isakmp policy 2
R1(config-ISAKMP) # BA 3des
Md5 hash of R1(config-ISAKMP) #.
# Preshared authentication R1(config-ISAKMP)
Group R1(config-ISAKMP) # 2
Output R1(config-ISAKMP) #.
R1 (config) # CUSTOMER - VPN crypto isakmp client configuration group
R1(config-ISAKMP-Group) # key xxxxxxxx
R1(config-ISAKMP-Group) # 192.168.0.1 dns
R1(config-ISAKMP-Group) # VPN - pool
ACL R1(config-ISAKMP-Group) # 120
R1(config-ISAKMP-Group) max-users # 5
Output R1(config-ISAKMP-Group) #.
R1 (config) # ip local pool VPN-pool 192.168.0.20 192.168.0.25
R1 (config) # crypto ipsec transform-set encrypt-method-1 esp-3des esp-sha-hmac
R1 (config) # crypto ipsec VPN-profile-1 profile
R1(IPSec-Profile) # set the transform-set encrypt method 1
Tunnel type interface virtual-Template2 R1 (config) #.
R1(Config-if) # ip unnumbered FastEthernet0/0
R1(Config-if) # tunnel mode ipsec ipv4
Ipsec protection tunnel R1(Config-if) # VPN - profile - 1 profile
Profile of R1 (config) # isakmp crypto vpn-ike-profile-1
R1(conf-ISA-Prof) # match group identity CUSTOMER VPN
R1(conf-ISA-Prof) # vpn_xauth_ml_1 list client authentication
R1(conf-ISA-Prof) # isakmp authorization list vpn_group_ml_1
R1(conf-ISA-Prof) # client configuration address respond
R1(conf-ISA-Prof) virtual-model # 2
Then run AccessList 120 for desired traffic ("access-list 120 now allows ip any any")
I have configured my VPN Cisco "CUSTOMER-VPN" clients and relative password
Whenever they connect, they are prompted for the password and username phase2 then they join the VPN with an IP address from local subnet released.
With the same parameters required and confirmed in section ipsec VPN Iphone it does not work.
It's 877 isakmp debug output after that Iphone wonder name of user and password (then I suppose that phase 1 completed):
* 14:29:30.731 May 19: ISAKMP (0:2081): received 151.38.197.143 packet 500 Global 500 (R) sport dport CONF_XAUTH
* 14:29:30.735 May 19: ISAKMP: (2081): responsible for operation of 151.38.197.143 of treatment. Message ID =-1427983983
* 14:29:30.735 May 19: ISAKMP: Config payload RESPONSE
* 14:29:30.735 May 19: ISAKMP/xauth: response XAUTH_USER_NAME_V2 attribute
* 14:29:30.735 May 19: ISAKMP/xauth: response XAUTH_USER_PASSWORD_V2 attribute
* 14:29:30.735 May 19: ISAKMP: (2081): node-1427983983 error suppression FALSE reason "made with Exchange of request/response xauth.
* 14:29:30.735 May 19: ISAKMP: (2081): entry = IKE_MESG_FROM_PEER, IKE_CFG_REPLY
* 14:29:30.735 May 19: ISAKMP: (2081): former State = new State IKE_XAUTH_REQ_SENT = IKE_XAUTH_AAA_CONT_LOGIN_AWAIT
* 14:29:30.743 May 19: ISAKMP: node set 1322685842 to CONF_XAUTH
* 19 May 14:29:30.747: ISAKMP: (2081): launch peer 151.38.197.143 config. ID = 1322685842
* 19 May 14:29:30.747: ISAKMP: (2081): lot of 151.38.197.143 sending my_port 500 peer_port 500 (R) CONF_XAUTH
* 14:29:30.747 May 19: ISAKMP: (2081): sending a packet IPv4 IKE.
* 14:29:30.747 May 19: ISAKMP: (2081): entry = IKE_MESG_FROM_AAA, IKE_AAA_CONT_LOGIN
* 14:29:30.747 May 19: ISAKMP: (2081): former State = new State IKE_XAUTH_AAA_CONT_LOGIN_AWAIT = IKE_XAUTH_SET_SENT
* 14:29:31.299 May 19: ISAKMP (0:2081): received 151.38.197.143 packet 500 Global 500 (R) sport dport CONF_XAUTH
* 14:29:31.299 May 19: ISAKMP: (2081): responsible for operation of 151.38.197.143 of treatment. Message ID = 1322685842
* 14:29:31.299 May 19: ISAKMP: Config payload ACK
* 19 May 14:29:31.303: ISAKMP: (2081): XAUTH ACK processed
* 14:29:31.303 May 19: ISAKMP: (2081): error suppression node 1322685842 FALSE basis "Mode of Transaction.
* 14:29:31.303 May 19: ISAKMP: (2081): talking to a customer of the unit
* 14:29:31.303 May 19: ISAKMP: (2081): entry = IKE_MESG_FROM_PEER, IKE_CFG_ACK
* 14:29:31.303 May 19: ISAKMP: (2081): former State = new State IKE_XAUTH_SET_SENT = IKE_P1_COMPLETE
* 14:29:31.303 May 19: ISAKMP: (2081): entry = IKE_MESG_INTERNAL, IKE_PHASE1_COMPLETE
* 14:29:31.303 May 19: ISAKMP: (2081): former State = new State IKE_P1_COMPLETE = IKE_P1_COMPLETE
* 19 May 14:29:31.303: IPSEC (key_engine): had an event of the queue with 1 KMI message (s)
* 14:29:31.315 May 19: ISAKMP: (2081): entry = IKE_MESG_INTERNAL, IKE_PHASE1_COMPLETE
* 14:29:31.315 May 19: ISAKMP: (2081): former State = new State IKE_P1_COMPLETE = IKE_P1_COMPLETE
* 14:29:31.623 may 19: ISAKMP (0:2081): received 151.38.197.143 packet 500 Global 500 (R) sport dport QM_IDLE
* 14:29:31.623 may 19: ISAKMP: node set-851463821 to QM_IDLE
* 14:29:31.623 may 19: ISAKMP: (2081): responsible for operation of 151.38.197.143 of treatment. Message ID =-851463821
* 14:29:31.623 may 19: ISAKMP: Config payload REQUEST
* 14:29:31.623 may 19: ISAKMP: (2081): verification of claim:
* 14:29:31.623 may 19: ISAKMP: IP4_ADDRESS
* 14:29:31.623 may 19: ISAKMP: IP4_NETMASK
* 14:29:31.623 may 19: ISAKMP: IP4_DNS
* 14:29:31.623 may 19: ISAKMP: IP4_NBNS
* 14:29:31.623 may 19: ISAKMP: ADDRESS_EXPIRY
* 14:29:31.623 may 19: ISAKMP: APPLICATION_VERSION
* 14:29:31.623 may 19: ISAKMP: MODECFG_BANNER
* 14:29:31.623 may 19: ISAKMP: domaine_par_defaut
* 14:29:31.623 may 19: ISAKMP: SPLIT_DNS
* 14:29:31.623 may 19: ISAKMP: SPLIT_INCLUDE
* 14:29:31.623 may 19: ISAKMP: INCLUDE_LOCAL_LAN
* 14:29:31.623 may 19: ISAKMP: PFS
* 14:29:31.623 may 19: ISAKMP: MODECFG_SAVEPWD
* 14:29:31.623 may 19: ISAKMP: FW_RECORD
* 14:29:31.623 may 19: ISAKMP: serveur_sauvegarde
* 14:29:31.623 may 19: ISAKMP: MODECFG_BROWSER_PROXY
* 14:29:31.627 May 19: ISAKMP/author: author asks for CUSTOMER-VPNsuccessfully group AAA
* 14:29:31.627 May 19: ISAKMP: (2081): entry = IKE_MESG_FROM_PEER, IKE_CFG_REQUEST
* 14:29:31.627 May 19: ISAKMP: (2081): former State = new State IKE_P1_COMPLETE = IKE_CONFIG_AUTHOR_AAA_AWAIT
* 14:29:31.627 May 19: ISAKMP: (2081): attributes sent in the message:
* 19 May 14:29:31.627: address: 0.2.0.0
* 19 May 14:29:31.627: ISAKMP: (2081):address of 192.168.0.21 assignment
* 14:29:31.627 May 19: ISAKMP: sending private address: 192.168.0.21
* 14:29:31.627 May 19: ISAKMP: send the subnet mask: 255.255.255.0
* 14:29:31.631 May 19: ISAKMP: sending IP4_DNS server address: 192.168.0.1
* 14:29:31.631 May 19: ISAKMP: sending ADDRESS_EXPIRY seconds left to use the address: 3576
* 14:29:31.631 May 19: ISAKMP: string APPLICATION_VERSION sending: Cisco IOS software, software C870 (C870-ADVIPSERVICESK9-M), Version 12.4 (15) T7, VERSION of the SOFTWARE (fc3)
Technical support: http://www.cisco.com/techsupport
Copyright (c) 1986-2008 by Cisco Systems, Inc.
Updated Friday 14 August 08 07:43 by prod_rel_team
* 14:29:31.631 May 19: ISAKMP: split shipment include the name Protocol 120 network 0.0.0.0 mask 0.0.0.0 0 src port 0, port 0 DST
* 14:29:31.631 May 19: ISAKMP: sending save the password answer value 0
* 19 May 14:29:31.631: ISAKMP: (2081): respond to peer 151.38.197.143 config. ID =-851463821
* 19 May 14:29:31.631: ISAKMP: (2081): lot of 151.38.197.143 sending my_port 500 peer_port 500 (R) CONF_ADDR
* 14:29:31.631 May 19: ISAKMP: (2081): sending a packet IPv4 IKE.
* 14:29:31.631 May 19: ISAKMP: (2081): node-851463821 error suppression FALSE reason "error no.".
* 14:29:31.631 May 19: ISAKMP: (2081): talking to a customer of the unit
* 14:29:31.631 May 19: ISAKMP: (2081): entry = IKE_MESG_FROM_AAA, IKE_AAA_GROUP_ATTR
* 14:29:31.631 May 19: ISAKMP: (2081): former State = new State IKE_CONFIG_AUTHOR_AAA_AWAIT = IKE_P1_COMPLETE
* 14:29:31.635 May 19: ISAKMP: (2081): entry = IKE_MESG_INTERNAL, IKE_PHASE1_COMPLETE
* 14:29:31.635 May 19: ISAKMP: (2081): former State = new State IKE_P1_COMPLETE = IKE_P1_COMPLETE
Here the Iphone remains unused for a few seconds...
* 14:29:48.391 May 19: ISAKMP (0:2081): received 151.38.197.143 packet 500 Global 500 (R) sport dport QM_IDLE
* 14:29:48.391 May 19: ISAKMP: node set 1834509506 to QM_IDLE
* 19 May 14:29:48.391: ISAKMP: (2081): HASH payload processing. Message ID = 1834509506
* 19 May 14:29:48.391: ISAKMP: (2081): treatment of payload to DELETE. Message ID = 1834509506
* 14:29:48.391 May 19: ISAKMP: (2081): peer does not paranoid KeepAlive.
* 14:29:48.395 May 19: ISAKMP: (2081): peer does not paranoid KeepAlive.
* 14:29:48.395 May 19: ISAKMP: (2081): removal of HIS right State 'No reason' (R) QM_IDLE (post 151.38.197.143)
* 14:29:48.395 May 19: ISAKMP: (2081): error suppression node 1834509506 FALSE reason 'informational (en) State 1.
* 19 May 14:29:48.395: IPSEC (key_engine): had an event of the queue with 1 KMI message (s)
* 19 May 14:29:48.395: IPSEC (key_engine_delete_sas): rec would notify of ISAKMP
* 19 May 14:29:48.395: IPSEC (key_engine_delete_sas): remove all SAs shared with peer 151.38.197.143
* 14:29:48.395 May 19: ISAKMP: node set-1711408233 to QM_IDLE
* 19 May 14:29:48.395: ISAKMP: (2081): lot of 151.38.197.143 sending my_port 500 peer_port 500 (R) QM_IDLE
* 14:29:48.395 May 19: ISAKMP: (2081): sending a packet IPv4 IKE.
* 14:29:48.399 May 19: ISAKMP: (2081): purge the node-1711408233
* 14:29:48.399 May 19: ISAKMP: (2081): entry = IKE_MESG_INTERNAL, IKE_PHASE1_DEL
* 14:29:48.399 May 19: ISAKMP: (2081): former State = new State IKE_P1_COMPLETE = IKE_DEST_SA
* 14:29:48.399 May 19: ISAKMP: (2081): removal of HIS right State 'No reason' (R) QM_IDLE (post 151.38.197.143)
* 14:29:48.399 May 19: ISAKMP: (0): cannot decrement IKE Call Admission Control incoming_active stat because he's already 0.
* 14:29:48.399 May 19: ISAKMP (0:2081): return address 192.168.0.21 to pool
* 14:29:48.399 May 19: ISAKMP: Unlocking counterpart struct 0 x 84084990 for isadb_mark_sa_deleted(), count 0
* 14:29:48.399 May 19: ISAKMP: return address 192.168.0.21 to pool
* 14:29:48.399 May 19: ISAKMP: delete peer node by peer_reap for 151.38.197.143: 84084990
* 14:29:48.399 May 19: ISAKMP: return address 192.168.0.21 to pool
* 14:29:48.403 May 19: ISAKMP: (2081): node-1427983983 error suppression FALSE reason 'IKE deleted.
* 14:29:48.403 May 19: ISAKMP: (2081): error suppression node 1322685842 FALSE reason 'IKE deleted.
* 14:29:48.403 May 19: ISAKMP: (2081): node-851463821 error suppression FALSE reason 'IKE deleted.
* 14:29:48.403 May 19: ISAKMP: (2081): error suppression node 1834509506 FALSE reason 'IKE deleted.
* 14:29:48.403 May 19: ISAKMP: (2081): entry = IKE_MESG_FROM_PEER, IKE_MM_EXCH
* 14:29:48.403 May 19: ISAKMP: (2081): former State = new State IKE_DEST_SA = IKE_DEST_SA
* 19 May 14:29:48.403: IPSEC (key_engine): had an event of the queue with 1 KMI message (s)
It seems 877 comes even to assign a local ip address of LAN for Iphone (192.168.0.21) but then something goes wrong...
Any idea or suggestion on this?
Thank you very much
Hi Federico,.
Please let us know.
Please mark this message as answered while others will be able to learn the lessons.
Thank you.
Portu.
-
Another problem with the configuration of Cisco VPN Client access VPN Site2site
We have a Cisco ASA 5505 at our CORP. branch I configured the VPN Site2Site to our COLO with a Juniper SRX220h, to another site works well, but when users access the home Cisco VPN client, they cannot ping or SSH through the Site2Site. JTACS contacted and they said it is not on their end, so I tried to contact Cisco TAC, no support. So here I am today, after for the 3 days (including Friday of last week) of searching the Internet for more than 6 hours per day and try different examples of other users. NO LUCK. The VPN client shows the route secure 10.1.0.0
Sorry to post this, but I'm frustrated and boss breathing down my neck to complete it.
CORP netowrk 192.168.1.0
IP VPN 192.168.12.0 pool
Colo 10.1.0.0 internal ip address
Also, here's an example of my config ASA
: Saved
:
ASA Version 8.2 (1)
!
hostname lwchsasa
names of
name 10.1.0.1 colo
!
interface Vlan1
nameif inside
security-level 100
IP 192.168.1.1 255.255.255.0
!
interface Vlan2
backup interface Vlan12
nameif outside_pri
security-level 0
IP 64.20.30.170 255.255.255.248
!
interface Vlan12
nameif backup
security-level 0
IP 173.165.159.241 255.255.255.248
!
interface Ethernet0/0
switchport access vlan 2
!
interface Ethernet0/1
switchport access vlan 12
!
interface Ethernet0/2
!
interface Ethernet0/3
!
interface Ethernet0/4
!
interface Ethernet0/5
!
interface Ethernet0/6
!
interface Ethernet0/7
!
passive FTP mode
permit same-security-traffic inter-interface
permit same-security-traffic intra-interface
object-group network NY
object-network 192.168.100.0 255.255.255.0
BSRO-3387 tcp service object-group
port-object eq 3387
BSRO-3388 tcp service object-group
port-object eq 3388
BSRO-3389 tcp service object-group
EQ port 3389 object
object-group service tcp OpenAtrium
port-object eq 8100
object-group service Proxy tcp
port-object eq 982
VOIP10K - 20K udp service object-group
10000 20000 object-port Beach
the clientvpn object-group network
object-network 192.168.12.0 255.255.255.0
APEX-SSL tcp service object-group
Description of Apex Dashboard Service
port-object eq 8586
object-group network CHS-Colo
object-network 10.1.0.0 255.255.255.0
the DM_INLINE_NETWORK_1 object-group network
object-network 192.168.1.0 255.255.255.0
host of the object-Network 64.20.30.170
object-group service DM_INLINE_SERVICE_1
the purpose of the ip service
ICMP service object
service-object icmp traceroute
the purpose of the service tcp - udp eq www
the tcp eq ftp service object
the purpose of the tcp eq ftp service - data
the eq sqlnet tcp service object
EQ-ssh tcp service object
the purpose of the service udp eq www
the eq tftp udp service object
object-group service DM_INLINE_SERVICE_2
the purpose of the ip service
ICMP service object
EQ-ssh tcp service object
inside_nat0_outbound to access ip 192.168.1.0 scope list allow 255.255.255.0 clientvpn object-group
inside_nat0_outbound to access ip 192.168.1.0 scope list allow 255.255.255.0 object-group NY
inside_nat0_outbound to access ip 192.168.1.0 scope list allow 255.255.255.0 object-group CHS-Colo
inside_nat0_outbound list of allowed ip extended access any 192.168.12.0 255.255.255.0
outside_pri_1_cryptomap to access ip 192.168.1.0 scope list allow 255.255.255.0 object-group NY
outside_pri_access_in list extended access permit tcp any interface outside_pri eq www
outside_pri_access_in list extended access permit tcp any outside_pri eq https interface
outside_pri_access_in list extended access permit tcp any interface outside_pri eq 8100
outside_pri_access_in list extended access permit tcp any outside_pri eq idle ssh interface
outside_pri_access_in list extended access permit icmp any any echo response
outside_pri_access_in list extended access permit icmp any any source-quench
outside_pri_access_in list extended access allow all unreachable icmp
outside_pri_access_in list extended access permit icmp any one time exceed
outside_pri_access_in list extended access permit tcp any 64.20.30.168 255.255.255.248 eq 8586
levelwingVPN_splitTunnelAcl list standard access allowed 192.168.1.0 255.255.255.0
levelwingVPN_splitTunnelAcl list standard access allowed 10.1.0.0 255.255.255.0
outside_pri_cryptomap to access ip 192.168.1.0 scope list allow 255.255.255.0 object-group CHS-Colo
backup_nat0_outbound list extended access allowed object-group DM_INLINE_NETWORK_1 192.168.12.0 ip 255.255.255.0
outside_pri_cryptomap_1 list extended access allow DM_INLINE_SERVICE_2 of object-group 192.168.1.0 255.255.255.0 10.1.0.0 255.255.255.0
outside_19_cryptomap to access extended list ip 192.168.12.0 allow 255.255.255.0 10.1.0.0 255.255.255.0
inside_nat0_outbound_1 to access ip 192.168.1.0 scope list allow 255.255.255.0 object-group CHS-Colo
VPN-Corp-Colo extended access list permits object-group DM_INLINE_SERVICE_1 192.168.12.0 255.255.255.0 10.1.0.0 255.255.255.0
Note to OUTSIDE-NAT0 NAT0 customer VPN remote site access-list
OUTSIDE-NAT0 192.168.12.0 ip extended access list allow 255.255.255.0 10.1.0.0 255.255.255.0
L2LVPN to access extended list ip 192.168.12.0 allow 255.255.255.0 10.1.0.0 255.255.255.0
pager lines 24
Enable logging
debug logging in buffered memory
exploitation forest asdm warnings
record of the rate-limit unlimited level 4
destination of exports flow inside 192.168.1.1 2055
timeout-rate flow-export model 1
Within 1500 MTU
outside_pri MTU 1500
backup of MTU 1500
local pool LVCHSVPN 192.168.12.100 - 192.168.12.254 255.255.255.0 IP mask
no failover
ICMP unreachable rate-limit 100 burst-size 5
ICMP allow any inside
ICMP allow any outside_pri
don't allow no asdm history
ARP timeout 14400
NAT-control
interface of global (outside_pri) 1
Global 1 interface (backup)
NAT (inside) 0-list of access inside_nat0_outbound
NAT (inside) 0 inside_nat0_outbound_1 list of outdoor access
NAT (inside) 1 0.0.0.0 0.0.0.0
NAT (outside_pri) 0-list of access OUTSIDE-NAT0
backup_nat0_outbound (backup) NAT 0 access list
static TCP (inside outside_pri) interface https 192.168.1.45 https netmask 255.255.255.255 dns
static TCP (inside outside_pri) interface 192.168.1.45 www www netmask 255.255.255.255 dns
static TCP (inside outside_pri) interface 8586 192.168.1.45 8586 netmask 255.255.255.255 dns
static (inside, inside) tcp interface 8100 192.168.1.45 8100 netmask 255.255.255.255 dns
Access-group outside_pri_access_in in the outside_pri interface
Route 0.0.0.0 outside_pri 0.0.0.0 64.20.30.169 1 track 1
Backup route 0.0.0.0 0.0.0.0 173.165.159.246 254
Timeout xlate 03:00
Conn Timeout 0:00:00 half-closed 0:30:00 udp icmp from 01:00 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 01:00 uauth uauth absolute inactivity from 01:00
timeout tcp-proxy-reassembly 0:01:00
dynamic-access-policy-registration DfltAccessPolicy
AAA authentication enable LOCAL console
AAA authentication http LOCAL console
the ssh LOCAL console AAA authentication
http server enable 981
http 192.168.1.0 255.255.255.0 inside
http 0.0.0.0 0.0.0.0 outside_pri
http 0.0.0.0 0.0.0.0 backup
SNMP server group Authentication_Only v3 auth
SNMP-server host inside 192.168.1.47 survey community lwmedia version 2 c
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown cold start
Sysopt connection tcpmss 1200
monitor SLA 123
type echo protocol ipIcmpEcho 216.59.44.220 interface outside_pri
Annex ALS life monitor 123 to always start-time now
Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac
Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac
Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac
Crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac
Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac
Crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
Crypto ipsec transform-set ESP-AES-128-MD5-esp - aes esp-md5-hmac
Crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
Crypto ipsec transform-set esp-3des-sha1 esp-3des esp-sha-hmac
Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
life crypto ipsec security association seconds 28800
Crypto ipsec kilobytes of life - safety 4608000 association
Crypto ipsec df - bit clear-df outside_pri
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 pfs Group1 set
Crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 value transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5
card crypto outside_pri_map 1 match address outside_pri_1_cryptomap
card crypto outside_pri_map 1 set pfs
peer set card crypto outside_pri_map 1 50.75.217.246
card crypto outside_pri_map 1 set of transformation-ESP-AES-256-MD5
card crypto outside_pri_map 2 match address outside_pri_cryptomap
peer set card crypto outside_pri_map 2 216.59.44.220
card crypto outside_pri_map 2 the value transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5
86400 seconds, duration of life card crypto outside_pri_map 2 set security-association
card crypto outside_pri_map 3 match address outside_pri_cryptomap_1
peer set card crypto outside_pri_map 3 216.59.44.220
outside_pri_map crypto map 3 the value transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5
outside_pri_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP
card crypto outside_pri_map interface outside_pri
crypto isakmp identity address
ISAKMP crypto enable outside_pri
crypto ISAKMP policy 5
preshared authentication
3des encryption
sha hash
Group 2
life 86400
crypto ISAKMP policy 10
preshared authentication
the Encryption
sha hash
Group 2
life 86400
crypto ISAKMP policy 30
preshared authentication
aes-256 encryption
md5 hash
Group 2
life 86400
crypto ISAKMP policy 50
preshared authentication
aes encryption
md5 hash
Group 2
life 86400
!
track 1 rtr 123 accessibility
Telnet timeout 5
SSH 192.168.1.0 255.255.255.0 inside
SSH timeout 5
Console timeout 0
management-access inside
dhcpd auto_config outside_pri
!
dhcpd address 192.168.1.51 - 192.168.1.245 inside
dhcpd dns 8.8.8.8 8.8.4.4 interface inside
rental contract interface 86400 dhcpd inside
dhcpd field LM inside interface
dhcpd allow inside
!
a basic threat threat detection
statistical threat detection port
Statistical threat detection Protocol
Statistics-list of access threat detection
a statistical threat detection host number rate 2
no statistical threat detection tcp-interception
WebVPN
port 980
allow inside
Select outside_pri
enable SVC
attributes of Group Policy DfltGrpPolicy
VPN-idle-timeout no
Protocol-tunnel-VPN IPSec l2tp ipsec svc webvpn
internal GroupPolicy2 group strategy
attributes of Group Policy GroupPolicy2
Protocol-tunnel-VPN IPSec svc
internal levelwingVPN group policy
attributes of the strategy of group levelwingVPN
Protocol-tunnel-VPN IPSec svc webvpn
Split-tunnel-policy tunnelspecified
value of Split-tunnel-network-list levelwingVPN_splitTunnelAcl
username password encrypted Z74.JN3DGMNlP0H2 privilege 0 aard
aard attribute username
VPN-group-policy levelwingVPN
type of remote access service
rcossentino 4UpCXRA6T2ysRRdE encrypted password username
username rcossentino attributes
VPN-group-policy levelwingVPN
type of remote access service
bcherok evwBWqKKwrlABAUp encrypted password username
username bcherok attributes
VPN-group-policy levelwingVPN
type of remote access service
rscott nIOnWcZCACUWjgaP encrypted password privilege 0 username
rscott username attributes
VPN-group-policy levelwingVPN
sryan 47u/nJvfm6kprQDs password encrypted username
sryan username attributes
VPN-group-policy levelwingVPN
type of nas-prompt service
username, password cbruch a8R5NwL5Cz/LFzRm encrypted privilege 0
username cbruch attributes
VPN-group-policy levelwingVPN
type of remote access service
apellegrino yy2aM21dV/11h7fR password encrypted username
username apellegrino attributes
VPN-group-policy levelwingVPN
type of remote access service
username rtuttle encrypted password privilege 0 79ROD7fRw5C4.l5
username rtuttle attributes
VPN-group-policy levelwingVPN
username privilege 15 encrypted password vJFHerTwBy8dRiyW levelwingadmin
username password nbrothers Amjc/rm5PYhoysB5 encrypted privilege 0
username nbrothers attributes
VPN-group-policy levelwingVPN
clong z.yb0Oc09oP3/mXV encrypted password username
clong attributes username
VPN-group-policy levelwingVPN
type of remote access service
username, password finance 9TxE6jWN/Di4eZ8w encrypted privilege 0
username attributes finance
VPN-group-policy levelwingVPN
Protocol-tunnel-VPN IPSec l2tp ipsec svc webvpn
type of remote access service
IPSec-attributes tunnel-group DefaultL2LGroup
Disable ISAKMP keepalive
tunnel-group 50.75.217.246 type ipsec-l2l
IPSec-attributes tunnel-group 50.75.217.246
pre-shared-key *.
Disable ISAKMP keepalive
type tunnel-group levelwingVPN remote access
tunnel-group levelwingVPN General-attributes
address LVCHSVPN pool
Group Policy - by default-levelwingVPN
levelwingVPN group of tunnel ipsec-attributes
pre-shared-key *.
tunnel-group 216.59.44.221 type ipsec-l2l
IPSec-attributes tunnel-group 216.59.44.221
pre-shared-key *.
tunnel-group 216.59.44.220 type ipsec-l2l
IPSec-attributes tunnel-group 216.59.44.220
pre-shared-key *.
Disable ISAKMP keepalive
!
!
!
Policy-map global_policy
!
context of prompt hostname
Cryptochecksum:ed7f4451c98151b759d24a7d4387935b
: end
Hello
It seems to me that you've covered most of the things.
You however not "said" Configuring VPN L2L that traffic between the pool of VPN and network camp should be in tunnel
outside_pri_cryptomap to access extended list ip 192.168.12.0 allow 255.255.255.0 object-group CHS-Colo
Although naturally the remote end must also the corresponding configurations for users of VPN clients be able to pass traffic to the site of the camp.
-Jouni
-
Cisco vpn client minimized in the taskbar and the rest in status: disconnect
I used 5.0.07.0240 cisco vpn client for 1 month with my pc under windows 7-64 bit. Worked well for 1 month. All of a sudden now when I double click the icon to start, VPN automatically minimizes to the taskbar with the disconnected state. It does not connect the option to hit or anything before it reduced to a minimum. I've not seen this before and no changes... but now it simply doesn't work. All solutions? Windows just patch automatically breaking cisco?
Unfortunately, cisco does not world class technical service... they called but no use.In my view, there is now a published version of the x 64 client, you need to download.If you suspect an update of Windows, why not try a system restore for a day, it wasworking correctly?On Wednesday, April 28, 2010 17:27:46 + 0000, akshay2112 wrote:> I used 5.0.07.0240 cisco vpn client for 1 month with my pc under windows 7-64 bit. Worked well for 1 month. All of a sudden now when I double click the icon to start, VPN automatically minimizes to the taskbar with the disconnected state. It does not connect the option to hit or anything before it reduced to a minimum. I've not seen this before and no changes... but now it simply doesn't work. All solutions? Windows just patch automatically breaking cisco? Unfortunately, cisco does not world class technical service... they called but no use.Barb Bowman www.digitalmediaphile.com
-
Problems to connect via the Cisco VPN client IPSec of for RV180W small business router
Hello
I tried to configure my router Cisco of RV180W as a customer VPN IPSec, but have encountered a problem that I hope someone can help me with. "" I managed to do the work of configuration so that the Cisco's VPN IPSec client authenticates successfully with the XAUTH user, I put on the router, but during the negotiation, the client ends with the following, which appears several times on the router error message: ' Mar 20 Oct 19:41:53 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for
> [34360] has no config mode. I've read around the internet and a number of people seem to say that the Cisco VPN Client is not compatible with the router, but the same thing happens to my iPhone VPN client.
Is it possible that this can be implemented? Below, I have attached the full configuration files and the log files. Thank you much in advance.
Router log file (I changed the IP
addresses > respectively as well as references to MAC addresses) Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: floating ports NAT - T with counterpart
> [44074]
Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] WARNING: notification to ignore INITIAL-CONTACT> [44074] because it is admitted only after the phase 1.
Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: NAT - D payload does not match for> [4500]
Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: NAT - D payload does not match for> [44074]
Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: received unknown Vendor ID
Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: received Vendor ID: CISCO-UNITY
Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: NAT detected: is located behind a device. NAT and alsoPeer is behind a NAT device
Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: request sending Xauth for> [44074]
Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: ISAKMP Security Association established for> [4500] - > [44074] with spi = >.
Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: receives the type of the attribute 'ISAKMP_CFG_REPLY' of> [44074]
Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: login successful for the user "myusername".
Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: myusername XAuthUser connected from the IP>
Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: sending of information Exchange: Notify payload [10381]
Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: receives the type of the attribute 'ISAKMP_CFG_REQUEST' of> [44074]
Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for> [44074] has no config mode
Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for> [44074] has no config mode
Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for> [44074] has no config mode
Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for> [44074] has no config mode
Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] WARNING: ignored attribute 5
Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for> [44074] has no config mode
Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for> [44074] has no config mode
Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for> [44074] has no config mode
Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for> [44074] has no config mode
Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for> [44074] has no config mode
Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for> [44074] has no config mode
Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] WARNING: attribute ignored 28683
Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for> [44074] has no mode config
Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] WARNING: attribute ignored 28684
Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for> [44074] has no config mode
Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for> [44074] has no mode config
Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: remove the invalid payload with doi:0.
Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: purged-Association of ISAKMP security with proto_id = ISAKMP and spi =>.
Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: myusername XAuthUser Logged Out of the IP>
Mar 20 Oct 20:03:16 2015 (GMT + 0000): [r1] [IKE] INFO: ISAKMP Security Association deleted for> [4500] - > [44074] with spi = > The router configuration
IKE policy
VPN strategy
Client configuration
Hôte : < router="" ip=""> >
Authentication group name: remote.com
Password authentication of the Group: mysecretpassword
Transport: Enable Transparent Tunneling; IPSec over UDP (NAT/PAT)
Username: myusername
Password: mypassword
Please contact Cisco.
Correct, the RV180 is not compatible with the Cisco VPN Client. The Iphone uses the Cisco VPN Client.
You can use the PPTP on the RV180 server to connect a PPTP Client.
In addition, it RV180 will allow an IPsec connection to third-party customers 3. Greenbow and Shrew Soft are 2 commonly used clients.
Maybe you are looking for
-
NASA TV shows white screen and convenient windows there is no problem
He worked something intill (I don't know Hat). Windows Explorer works with all the problems.
-
HP Envy 15 k046nd: Envy 15 k046nd how to remove the keyboard (shift of collage and key)
Hi all Short version: Does anyone know how to remove a single key on the keyboard without breaking? (or if it is still possible) I tried some things, but have failed. Long version: Unfortunately, I spilled lemonade on my keyboard last week. I cleaned
-
I have a HP Pavilion dv7 that will not start, just get flashing caps lock, shift, so I tried all usual ways of starts without battery etc. and I now have a new and I want to remove the hard drive from the old HP dv7 and plug it into the new laptop to
-
When installing fault! 0xc0190036! 2841/75497 (srchadmin.d77) shows upwards and the installation stalls.
-
Photosmart 2710 need to change region for the printer cartridges
Hello: I am an international resident currently residing in the Brazil. My printer is programmed for Asian print cartridges and the region needs to be changed so that I can buy cartridges locally. When I changed from Europe to Asia, HP Singapore supp