Cisco Wireless Lan Controller 2504

Similar Questions

• Are Cisco 1130ag APs compatible with Cisco Wireless LAN Controller virtual?

  Are Cisco 1130ag APs compatible with Cisco Wireless LAN Controller virtual?

  It's... AP compatibility depends on the code that runs on the WLC. This is a matrix that is a good reference.

  http://www.Cisco.com/en/us/docs/wireless/controller/5500/tech_notes/wire...

  Sent by Cisco Support technique iPhone App

• Routing using Wireless LAN Controller

  I was wondering if Wireless LAN controller (5508) can manage routing? This is our problem.

  We have a remote site, where we have bunch of 2900 series just pass. The router belongs and is managed by the provider of the PHONE company.

  We would like to install a controller (5508) and as the controller would make the delivery for the following subnets:

  The company 10.10.10.0/24 network

  Guest network 10.10.20.0/24

  Mobile (iPhone / iPad) 10.10.30.0/24

  Management Interface (AP) 10.10.40.0/24

  Is this possible? Or we need a layer 3 switch or a router that can do the routing for wireless controller.

  If possible, we prefer NOT to use the TELCO routing router subnet wireless?

  DS

  Unfortunately is the WLC a diverter. It is layer 2 only.

  Steve

  Sent by Cisco Support technique iPhone App

• Version of the software Cisco Wireless LAN controllers & Licensing (controllers HA and APs Adder & licenses basic questions)

  In fact, one of my clients has two Cisco 5508 wireless LAN controllers installed in a site and back up and running now. one of them running software version 7.4 and the other running software version 7.6. Each of them works as a stand-alone controller with number of access points. Based on this scenario, answer below concerns:

  • Can we transfer all active licenses at one of them and use it as a HA free of charge?

  • Up to which version of the software, we can improve these controllers without any extra charge?

  • What we must do if we want to move two of them to version 8 software?

  Waiting to hear from you soon about my concerns.

  Here are a few notes:

  -Only licenses Adder can be reheberges to another controller. Base license cannot be rehosted unless the unit is THAT RMA would be.

  -Too long the WLC has a minimum of 50 access point license, so that the unit can be used for HA N + 1 or AP SSO.

  s ' it use SSO of AP, the WLC must have connections to subnets for layer 2 even due to the IP address of the interface.

  HA N + 1 can be used in sites different especially if the subnet do not align

  -Scott

• Cisco 2112 and Apple TV Airplay wireless LAN Controller

  Hi all

  I'm having a problem with the help of iTunes, iPhones, and iPads on our wireless network. We have the WLC 2112 and 10 1142N WAP. If I do a network scan, I can see the Apple TV and port 5353 is open, which is Apple's morning service.  However, if I try to play the music/video on iTunes, or on an iPhone/iPad, I don't see the Airplay icon.  If I connect to the local network, the Airplay icon appears immediately. I created an allow all the rules in the ACL, but still no dice.  Any help would be greatly appreciated.

  THX

  Benm

  This Solution has been added in the following document

  https://supportforums.Cisco.com/docs/doc-21728

  If you have enabled IGMP snooping. To the title of controller, you have too many active multicast and multicast address?

• WebAuth LOCAL with Wireless Lan Controller and ISE

  Greetings,

  We intend to set up a centralised comments with sponsored webauth wireless network. I didn't know that this will not work with our current WLC code (6.0.199.4) as 7.2 or later version is required.

  We have a project to upgrade the WLCs but he won't be ready before the deadline for the completion of the reviews wireless.

  I am using local WebAuth temporarily until the WLCs are ready. My questions are:

  1. am I correct that I can still authenticate ISE?

  2. Since local webauth does not cost support, does that mean I can't apply a pre or post auth ACL?

  3. can someone point me to a good guide for configuring local webauth?

  Thank you!

  Hi Leroy,

  In CWA you can push the AVPs desire in the final result because of the nature of the flow:

  -Comments will connect to the SSID.

  -WLC send wireless MAB ask (1st authentication). In response, ISE returns accepted with url-redirect-acl and redirect url.

  -WLC updates the client session and once http (s) generated WLC redirects the customer to ISE according to AVPs received at the 1st auth(MAB request).

  -The customer enters the identification information in the portal. ISE valid creds and refers to WLC one type COA to re-authenticate.

  -WLC re authenticates the client (2nd authentication) session, and at this point ISE can support AVPs custom as names of VLANS, Interfaces or space air dynamic ACLs.

  -WLC overrides the client session with the new attributes.

  Local Web Auth as you mentioned, there are 2 steps but the WLC "considers" cela a single thread.

  To the LWA, the flow is as follows:

  -The client connects to the SSID.  Since there is no involved L2 auth client through DHCP, captures an IP and arrives at WebAuth_Required. Redirect URL is configured statically on WLC and pre auth ACL allows client access to ISE during the auth phase.

  -Customer opens the browser and WLC redirects the customer to ISE, but breast of redirection, there is a 'return to WLC' action which indicates to ISE to send customer WLC virtual IP containing identification information of the client used for auth in portal comments.

  -In this way the WLC now "knows" the handed creds to ISE and this way there is a formal request from RADIUS WLC sends to ISE asking these creds. ISE links in return an accept, and this is how the WLC now "knows" that auth is correct and she should move client to RUN.

  LOA of the simplest way would be to define an Interface of comments and statically applying a restrictive ACL at the level of the interface rather than wait the AVP of AAA server.

  LWA is supported in this version at very low level and basic, but if you want a complex flow involving the pusher of the dynamic attribute you will need something higher to 7.2.110.0.

  Recommended version would be 7.6.130.0 as for now.

  Kind regards

  Antonio

• Terms of wireless LAN Controller

  What is the purpose and reason for using virtual interface and port-management service, AP Manager?

  My bad... I mean WLC

  The Strip is telnet, ssh to the ip management. out of band is when the port has no real connection to your network. That is why the ip address of the service port is an ip address that is not part of your network shouldn't be routable in your network. In the case where your connection of loos to management and you do not know the commands for the cli, you can connect to the service port and use the GUI.

• Setting up autonomous HA - SKU Wireless Lan Controller

  Hello

  I ordered an AIR-CT5508-HA-K9. It is not match with WLC assets and there is no permanent AP license on this HA - SKU.

  I wonder if I can make any configuration or perform the software upgrade on the standalone HA - SKU?

  Thank you.

  You can do both, but you can use this HA - sku only for SINGLE sign-on or N + 1.  You can not use both as independent because you will get an error after 90 days.

  -Scott

  Evaluate the useful ticket *.

• wireless lan controller, allowing lag

  Hi all

  I used more than 47 ap on my 4402, and now he usually adds more, if I activate LAG happens with a WARNING saying it will delete all my interfaces, current - this true? or if I activate LAG it should still work as before?

  see you soon

  Carl,

  Activation of LAG does not remove interfaces.  So, if you activate the OFFSET and reboot, you should be fine.  Alternatively, you can configure another AP-Manager and bind it to the other port.

  See you soon,.
  Steve

  --

  If this helps you or answers to your question if it you please mark it as 'responded' or write it down, if other users can easily find it.

• Cisco NAC does support Wireless LAN?

  Hello

  I know that Cisco NAC support LAN wireless. I sent myself with various brands of autonomous APs. These work very well using the in-band, out-of-band mode.

  However, Cisco has been mentioned for Cisco AP, with Cisco switches and Cisco NAC, out-of-band is supported. I tried this today and it's or Cisco's fake, which is highly unlikely, or I have not configured the portion of the NAC or the access point Cisco correctly, which is most likely? I wonder where am I wrong? Please someone advice me on this?

  Kind regards

  RAM

  + 6012-2918870

  Hi Jean Claude,

  You can now do out-of-band with wireless deployments, but you must have a Wireless Lan Controller manage your APs. You can't do it with autonomous APs.

  The guide below will for most of the configuration:

  http://www.Cisco.com/en/us/products/ps6128/products_configuration_example09186a0080a138cc.shtml

  Thank you

  Nate

• Can not find the updated driver for Intel PRO Wireless LAN 2100 3B for R40

  I can't find the good updated software listed for my R40 on the Lenovo site. The Device Manager shows my card wireless as:
  Intel PRO Wireless LAN 2100 3B Mini PCI Adapter but I can not find the model listed in the update list.

  My R40 description is by Lenovo site is:
  Product: ThinkPad R40 2897 B4U
  Operating system: Windows XP

  Original description: P M 1.4 GHz, 256 MB RAM, 40 GB 4200 RPM drive HARD, XGA(1024x768) 15 TFT LCD, 32 MB ATI Radeon 7500, 24x10x24x/8 x CD-RW/DVD, Intel 802. 11B wireless (MPCI), Modem (CDC), 10/100 Ethernet (LOM), UltraNav, Secure Chip (TCPA), IEEE 1394, 8-cell Li-ion, WinXP Pro

  Lenovo driver update page, I have the following choices:

  Network: R40, R40e wireless
  (1) mini PCI driver of cisco Wireless LAN

  (2) high rate Wireless LAN Mini-PCI Adapter III
  Note: The models ThinkPad R40 2681, 2682, 2683

  (3) dual-Band 802.11ab and 802.11abg wireless LAN Mini PCI adapt

  (4) Intel PRO/Wireless LAN 2100 3B Mini PCI adapt
  Note: The models ThinkPad R40 2722, 2724 only, 2723

  My card is listed for models 2722 2723 and 2724 ONLY.

  Here is the direct link to the driver page http://www-307.ibm.com/pc/support/site.wss/document.do?lndocid=MIGR-46024R40.

  Device Manager shows that I currently have the Intel of the installed driver version: 07/03/2003, version 1.1.5.0

  Can anyone help on what version of the software update I should use?

  Welcome to the forum!

  Here is your wireless driver:

  http://www-307.IBM.com/PC/support/site.WSS/document.do?sitestyle=Lenovo&lndocid=MIGR-59438

  After you download it, make sure you unpack it in the following directory: C > drivers > win > Wlanint

  I hope this helps.

• Integration of CISCO ISE with another controller wireless lan of the seller

  Hi all!

  I am currently working on an assignment and eager to integrate the identity service provider in the network. the only problem is that the deployed wireless network earlier of another provider I just need to know that either ISE has integration with the other controller feature wireless provider and can provide guest access control. The LDAP integration is also required.

  Waiting for help!

  Hello

  According to my knowledge Yes, Cisco ISE can be integrated with another controller wireless LAN of the seller, but limited. (Aruba, Rukus) and if you want to add the external identity group to your network, then LDAP integration is required.

• Upgrade of Cisco Wireless Controller 4402

  We have a 4402 WLAN controller with a bunch of AP in 6 locations. The software is installed on a Windows Server 2003 server - since our society must be in accordance with various compliance agencies, we are in the process of getting rid of all 2003 servers in our infrastructure as they will be supported are more early next year.

  I created a new server (2012 R2) and tried to install, but get the error that it is only supported on Server 2003 or Red Hat.

  Is there a way to get this installed on one different platform other than 2003?

  Thank you!

  Yes, you can keep the same equipment (WLCs and AP).

  I was just saying about upgradation WCS to the CNS / prime infrastructure

  NCC/WCS are just a management for wireless LAN controllers APs. so if you change the WCS to the CNS, then it will affect any service.

  Concerning

  Remember messages useful rates

• 20 - r011il: driver for windows 8 64-bit wireless lan

  bcm43142a0 I am not able to find some drivers... "" - i.e. the driver wireless lan.

  and the other is... "network controller".

  He "Alwayse" said a problem of compatibility with this device.  I use windows 8 64-bit os.

  Please suggest any driver as soon as possible

  Hello:

  There is no drivers windows 8 for the model Broadcom wireless network adapter that has your laptop.

  I suggest that you connect through an ethernet cable, required for W8, so that you can ge updates free update for the Windows store W8.1, and then use the drivers your PC support page W8.1.

• Satellite U940 - update Realtek Wireless LAN Driver

  I just upgraded my Satellite U940 PSU6VA - 00S 002 Windows 8 to 8.1 of Windows and am currently following the instructions of the upgrade from here. I noticed that European and Australian Toshiba sites include a 'Realtek Wireless LAN Driver' in their list of downloads driver for Windows 8.1 for the Satellite U940:
  - European page
  -[http://support.toshiba-tie.co.jp/windows81/drivers/PSU6V_Up_au.htm]

  However, I have never noticed any a Realtek wireless LAN driver on my computer, before even that I have upgraded to Windows 8.1. I've only seen in Device Manager network cards:
  -Intel Centrino Wireless-N 2200
  -Realtek PCIe FE Family Controller (which I believe is a wired LAN driver, not a LAN wireless driver).

  So my question is: do I have to download the Realtek wireless network driver or is it not suitable for my system?

  > So my question is: do I have to download the Realtek wireless network driver or is it not suitable for my system?

  Your laptop was equipped with Intel wireless network adapter and NOT card Realtek WLan and therefore the Realtek WLan driver does not need to be installed.
  You should consider a fact: there are different laptops on the market models that are equipped with different material parts. Some support the Realtek WLan card and some models were equipped with modules WLan Intel and that's why you can find some drivers (like Realtek Bluetooth Driver Package Filter) in the driver from the list of downloads that are not essential for all models.