CLIQ: My phone signal strength is almost always-110 and lower

Similar Questions

• Tecra M2 and wireless network - signal strength problem

  Need advice buying wireless kit.

  I have a DSL phone line connection and I am currently using a Speedtouch USB modem connected to my workstation down.

  I have a laptop Toshiba Tecra M2 with construction of wireless support. I want to be able to share the internet connection which comes in the workstation down. I guess that my options for the workstation are to use a DSL wireless modem to share the internet connection or to use a PCI card in my computer. I tried them both.

  I first tried to set up an infra mode network with the laptop using a LinksysWAG54G which was connected to the telephone line and a computer. But the problem with that I was t couldn't do accept the subnet mask that my ISP (Lixxus) provided 255.255.255.255 (PPoA). This modem has all the masks of SN in a dropdown list, but mine isn't in this list. I returned this modem.

  I tried then set up an adhoc network purchase buy a PCI Wireless card for my desktop, and internet connection sharing etc. on the workstation. However, while it worked, and I could see the desktop of my laptop, the problem has been the wireless range. The signal disappear when I wore the laptop in the back room on the first floor. It would have been a distance of 10 meters in a straight line between the laptop and desktop. There are walls two bricks and a floor between the two machines. It seemed hopeless, so I sent the PCI card.

  I'm not sure what to try next.

  Any suggestions that I could try next?

  Suggested hardware?

  Signal strength - could the problem be that the antenna in portable insufficient Tosh - it too small?

  Hello

  I have the same situation at home. The best solution for this is to use the wireless router. Here you have the possibility to connect several computers desktop or laptop. In this case the configuration of wireless connection is very easy and it works fine. I also use it at home and in front of my house with no problems.

• P70 Pro SAT - signal strength dropped suddenly constantly

  I recently bought the Satellite P70 Pro (2 weeks ago). It has Intel Pro Wireless 2200BG adapter. During the first week, I was able to detect approximately 6 wireless LANs near my apartment and my own WLAN has always been the power of the signal full (I use a Belkin Wireless Access Point).

  I updated my Windows XP with updates of recommended security and after reboot, my laptop only barely detect my WLAN with very low signal strength at best, and I can't see all other WLANS that I used to work with the very good signal strength.

  I do not understand why this has happened - I tried tto updated drivers Intel cards with the latest version (9.0.3.9) and also to restore my system to the date I bought it (IE restore to basically its state before buying). None of these actions has changed the fact that he basically can't pick up my WLAN more unless I'm ontop of it.

  I think return the laptop and get the card replaced Intel because it seems defective.

  If anyone has any ideas they would be greatly appreciated.

  Thank you very much
  Peter.

  Hello

  I've read many users with different laptops, but with the same WiFi card have similar problems. Unfortunately have no explanation. I know that you can use the Agere or Toshiba WLAN card.

  In my opinion, this card doesn't work properly with some access points or there is a problem with communication between them. I have the same card (Satellite M40) and WLAN Netgear access point. Since the first day, it works perfectly and without any update driver.

  If you have time here to edge wireless you can find a lot of interesting topics on the similar theme.

  Good luck!

• How to test the signal strength of an Airport Express, which extends a network?

  I am trying to understand how my Airport Express is actually help to expand my network, and if I should move somewhere different. Any help would be appreciated!

  Current situation: my base station is an AirPort Extreme in our apartment computer room; for the internet, which is plugged into the wall. The wifi network is extended in the living room via an AirPort Express (version 7.6.4). There are on the same cabinet as the AirPort Express to Apple TV. The Airport Express has an optical cable connecting to a sound bar (which has an additional HDMI connection to the TV).

  I don't really know if the AirPort Express Terminal, he does something useful. The network is set to be extended, best I can tell: Airport Extreme network Mode is "Create a wireless network", and network Mode of the AirPort Express is "extend a wireless network. But still, the wifi on my iPad and iPhone signal strength seem to fall much in the living room. Apple TV usually broadcasts music from my desktop computer (in the computer room) well enough, but if I try to play music from my computer via the Apple Express at the soundbar, the connection is terrible and fall. (Which could be a problem with wifi, or could be an aging Airport Express question, could be a cable problem or might be a sound bar problem...)

  An example of what worries me: if I go to the Airport utility on my iPhone and a glance at the Airport Extreme, it has 4 Wireless, including Apple TV clients. But if I look at the AirPort Express, there sometimes a client wireless (iPhone), but never shows the Apple TV: even if the Apple TV is about 30 cm of the Airport Express. It's as if the 30cm distant to the Airport Express connection is weaker than the connection of two-rooms-distant Airport Extreme, but I am probably wrong that.

  In any case, is there a way to test what speed is through the AirPort Express, compared to through the extreme? I tried to use applications like CloudCheck on my iOS devices, but those only measure the speed of my network, and it is unclear whether or not he uses the Extreme or Express.

  Thanks in advance and all apologies if I used (almost inevitably) 'Express' when I should have used "Extreme", or vice versa, somewhere at the top.

  One way to see the strength of the signal is the Alt (option) key while clicking on the WiFi icon in the menu bar.

  But you see not directly related to the airport of arrival. Also the Airport utility does not give much information.

  You can see a lot more with the free app (Appstore) called "WiFi Scanner".

  The problem could be that the place you have chosen for the Airport Express can be better: it should be somewhere in halfway (in force) between the Real and where you sit with the iPad/iPhone.

• I want to test my cell signal strength

  I want to test my cell signal strength

  I think that could be solved by your carrier - it is they who provide the service and to know where are the towers. Other than that, your phone displays the intensity of the signal with the bars.

• WRT1900ACS - low wifi signal strength

  Finally, I returned my reboot constantly and lock WRT1900AC V1 and got a new WRT1900ACS in Exchange.  (Thanks for the service of 2 year contract with bestbuy).

  The intensity of the signal of the WRT1900AC V1 was regularly 3 to 6 DB louder than my Apple Airport.  It's one of the things that I really liked on the V1 WRT1900AC... good coverage.

  The WRT1900ACS is more stable, but the signal strength is very low compared to the Apple Airport.

  Here are the results of a test... in both cases I measured the signal strenth with my MacBook Air with the routers placed in the same position and from the same location.  I have reproduced this test of different areas of the House and in all cases, the airport was a signal much stronger.

  This is the airport.  RSSI is - 68 DBm, which is a very good signal.

  

  Now, here's the WRT1900ACS. RSSI is - 80dBm which is an almost unusable signal.

  

  So here are my questions to the experts of the group... would you say that this WRT1900ACS is defective and must be returned?  Or y at - it something on the ACS firmware that has changed (I'm currently running with the last 1.0.0.172978 rev).

  No amount of 4 on the WRT1900ACS antenna setting does make a difference.

  Looking for some ideas to try before returning this unit to another Exchange.

  Thank you

  For more insulation, we manually will reflash the firmware of the device. You can do the following:

  • Download the firmware.
  • Manually reflash the firmware of the device.
  • Reset and reconfigure the router. Furthermore, once you reset the router, all settings and configurations that were previously recorded will be deleted. You can save the setting of your router before the firmware update. Here is the link for the process.

  Observe how it goes and let us know for updates. So again, you will encounter the same setback, please send us an email to [email protected] with the following details:

  * Contact information

  * Location

  * Community user name and the link to this thread

• The signal strength

  I recently bought my Xperia Z3, which I love so far, but with one question. I seem to be getting low signal (never above 2 bars, approximately 100 dBm), but sometimes I have problems with slow data speeds, and I never have a problem with phone calls or send messages.

  Earlier I put the preferred network for WCDMA (3G) only mode, and my signal went up to 4 bars and about 60 dBm, which for me is great. I then put the mode preferred network to LTE, and my signal goes down again.

  I can't explain quite why this is - wouldn't be that my Z3 does not LTE very well? It cannot be the network, because my friends/family have great strength/signal LTE with different phones.

  Any input/thoughts would be greatly appreciated.

  Either a SIM card defective, wrong APN settings, low network coverage or your carrier/network should add the IMEI number to your account, so you can have multi-service LTE.

  Is your phone compatible with your carrier LTE bands?

• Low signal strength, high-end hardware

  My old adapter dead netgear recently. It has just stopped working. It worked fine until now, if a little slow, but he never gave me peaks of lag or sudden failures. I got a new Linksys adapter and went with the G because my old netgear adapter is a G. I noticed the signal strength is low, and when I played games online I was sometimes a hint of lag. I decided it might be time to update my router as well. So, I bought a N of Linksys wireless router. No change, still a power low signal and occasional spikes of lag. So I traded my linksys for Linksys Wireless-N router adapter. Higher speeds, but always a low signal strength. My router is down hard connected to a cable modem. That's about 30 feet of the card, with a couple of walls between the two. Should there be any reason why will not improve my signal strength, and I continue to experience spikes obstructive gal? I'd switch Netgear, because I never had this problem before trying to Linksys? Some advice, please.

  Not even a Word. Thanks for making my decision, Linksys.

  (Mod Note: under the direction of compliance from the forums.)

• the signal strength especially in car

  Had the Xperia Z3 Compact for less than a week, I put it through bluetooth to make calls from my car radio, but I now notice that the signal strength shows that 1-2 bars most of the time, the number goes up when I get out of the car. but I have to be able to use the phone in the car... my previous phone, was no problem, I got a bar showing (on radio and phone screen) today when I turned on the car, but my husbands phone showed 4, don't know if I will be able to receive calls... any help would be appreciated, thanks Roxane

  @roxane

  This should help you understand the power of the signal

  http://powerfulsignal.com/cell-signal-strength.aspx

  The second question is a joke

• BlackBerry Z10 Z10 and the carrier Signal strength

  I don't know if this is related to the question of appeals Z10 has dropped, but I noticed that my carrier signal strength jumps from full bars to (say) 2 shelves for the big X red for no reason my phone is just sitting there.

  This may be related, but I also calls recently, and my quality of phone (although normally I would say great) was virtually zero as if I had to drive into a tunnel (you know, that jerky digitized sound).  Actually, I was sitting in front of one of my rounds of carriers.

  I would appreciate ideas... I'm on OS 10.1.0.1720 official on Telus.

  I have the same problem on Rogers and my father done to MTS. We are in Manitoba. Very strange how it fluctuates constantly. Found in Toronto it was stable, and the LTE with Rogers.

• Fan runs almost always since the installation of Sierra and MacBook Air running Mac OS.

  Hello

  Since upgrading to Mac OS Sierra last night on my MacBook Air (2013, i7, 8gbRAM), fans work almost always, even when I use Safari.  Previously, the fans would go only when I was playing a game, or video edition.  The basis of my Macbook Air is also much more hot he was under El Capitan - once again, just when you use Safari.  As a result, my battery life is horrible - dropped from 100% to 23% in a little over an hour.  Once again, under El Capitan, if I was just using internet, use of an hour would see the maximum of 10 to 15% of decline in battery.

  I turned off my Macbook Air and it turned on again after fifteen minutes, but in 10-15 minutes, fans revived upward and the base (and the top of the keyboard) heated again.  No uncomfortable levels, but certainly noticeable levels.

  Just to remind - I use Safari only when this happens.  Moreover, since the beginning of this question five minutes ago, the % of battery has dropped from 29 percent to 22 percent and the fans are still whirring like the dickens.

  No idea why this is happening?

  Hello, take a look at this maybe of http://www.macworld.co.uk/feature/mac/fix-overheating-macbook-3592266/ article it will help.

• Firefox is very slow to respond when you open and almost always no longer meets the total even refusing to respond to the Task Manager "end program command @.» The ' does not not @ error also happens during navigation online.»

  Firefox is very slow to respond when you open and almost always unresponsive altogether, refusing even to respond to Manager task "End program" command. The "not responding" error message is also over browsing online. Several attempts must be made to get online. A loss of stability seems to be endemic at the present time.

  Try to follow the instructions here: Firefox crashes or does not - how to fix

• Portege M800: The fan is almost always on

  Hello!

  I have a Portege M800 M105 with Vista 64 bit. The fan is almost always on despite the fact that the temperature of the CPU is about 43 to 46 Grad Celsius and the CPU has nothing to do. I used the program Speedfan (http://www.almico.com/speedfan.php) to display the temperature. I find that the noise of the fan is very noisy.
  Is there a possibility to control the fan, so that it will be only noisy when the temperature is high?

  Best regards
  Sven

  Hello

  You are right. The Toshiba Power Saver for Win XP looks completely different as the Vista energy saver.
  But you can also change many settings in Vista energy saver that contribute to the use of the battery power decreases.

  The power settings are a bit hidden in the Vista energy saver but check this thread posted by Jayjay:
  http://forums.computers.Toshiba-Europe.com/forums/thread.jspa?threadID=38906&TSTART=0

  You will find a link to the doc of Toshiba:
  [How to manage Windows Vista power management features | http://aps2.toshiba-tro.de/kb0/HTD84026Q0000R01.htm]

  How to manage power settings in Vista there are has many useful tips.

  Hopw this helps.

  Good bye

• Portege Z830 - fan noisy and almost always running

  My new Portege Z830 has the issue of noisy fan and almost always running which has been said here before.

  Recommendations were that we download bios 1.6. But I checked and that the version is already installed on my machine. I also adjusted the power save mode battery parameters as others have suggested. But that made no difference,

  All the other tips has been give in technical language far this beginner.

  If anyone has any suggestions they might put in words of one syllable and the step by step instructions, I would be eternally grateful. Thank you.

  I found also two documents from Toshiba on exactly this topic and as saying that update BIOS version 1.60 or higher would solve the problem

  Portege / Satellite Z830 high cooling fan speed.
  http://APS2.toshiba-tro.de/KB0/TSB23039P0000R01.htm

  and

  How can I improve the control of the FAN on the Satellite and Portégé Z830?
  http://APS2.toshiba-tro.de/KB0/FAQ22039H0002R01.htm

• Saving settings Tecra M11 - fan almost always on

  Hello

  I have a Tecra M11 (Windows7 64-bit). Toshiba Power Saver Settings V8.9.3.64 are installed.

  My problem is: fan is almost always turned on with maximum speed, in which case there is no load on the CPU (only 1 to 5%). It's really loud and annoying!

  What I've done so far: I changed the method of cooling to the "battery optimized" to two changes of power, but without effect.

  Question:
  (1) are there any available desktop mode (as many other manufacturers of laptops offers for professional laptops) to work in a quiet environment?
  (2) is there an option to uninstall the Toshiba Power Saver Settings and use the standard cooling Windows7, because Windows 7 has generally a passive cooling option with the effect that the fan is off.

  Thank you very much!
  Frank

  I m really wondering what cooling settings method didn't help. I have Tecra A11 with Win7 64 bit and my laptop is absolutely silent. Changes to these settings on several other portable Toshiba the result was the same. Laptop has been much quieter.

  Which power plan do you use?
  Have you noticed a difference when you switch to the Toshiba eco mode?

  Answers:
  # All I know this mode is not available on Toshiba laptops.
  # You can remove Toshiba power saver, but it's a little complicated. You must remove any additional package from Toshiba. Later, you must install VAP again but not as standard but custom mode and remove check mark in front of the applications, you don t want to install.