CLJ 9500 MFP power

Similar Questions

• CLJ CM4540 MFP problems

  I'm working on a CLJ CM4540 MFP that turned to mush!  Initially as being very noisy when printing, but it did print without any other problems.  I replaced the main bearing and four engines (not something for the faint of heart!).  After finding several connectors that I had left disconnected, he started having some 51.00.19; 51.00.22; 51.00.23 errors, asking all about laser assemblies.  I made sure that the cables going to the lasers have been correctly connected but no change.  Tried a new controller DC Council because it is a common point for lasers (and just about everything else too) without modification.  Tried reloading the firmware without change.  I'm starting to lean towards putting the former main drive assembly into the printer to see if this could be the cause, although I don't know how it could be.  I get also get 99.05.56 errors intermittently (Firmware not loaded correctly) and 30.01.49 (Scanner not powered).

  Any thoughts on a cause?

  Well, I finally fixed!  I put the hand in the car with the dc controller.  Still no go, control panel lights up but no noise motor or fan noise.  Do you have a few power checks and I got voltage going to the Formatter Board, but almost nowhere else!  I replaced the LVPS to solve the problem.

• 175NW MFP POWER MANAGEMENT

  LASERJET PRO100 COLOR MFP M175NW, WINDOWS XP OPERATING SYSTEM.

  Y DOES IT HURT TO LEAVE THE POWER 'ON' WHEN YOU KNOW THAT YOU NEED TO PRINT NOT FOR A DAY OR MORE?

  I TRIED TURNING "OFF" POWER ONLY TO FIND IT GOES THRU A REINSTALL WHEN I TURN THEN POWER.

  Hi GWINABOR,

  No, there is nothing to fear leaving the printer on. It gets low when energy saving mode not used.

• Failure to scan HP CLJ CM4730 MFP 30.01.34

  I have one of these with failure scanner error 30.01.34 as well as some mistakes of fan... 57.03 57.06 57.7. One of our IT guys replaced the trainer and the LVPS. No help. The 30.01.34 error does not appear in the maintenance manual, but it seems that the only thing in common with errors is the DC controller... Engine test button does nothing, the device does not print. Anyone got any suggestions? (other that pass on to the next guy)

  At the time current diagnoses is not possible, so if I had thoughts that I would at least try spec it.

  Remove the cartridges, belt, trainer, fuser, also remove the connection to the Scanner and ADF so I got just the print engine.

  See if I get any sign of life to the power upward, if you are fans of spin for example then you have the DC controller is probably working signs.

  If not then at least I know that I would be on the base engine failures and would probably be cut as much as possible see what I can do to make it live.

  The reason to take the fuser out, the LVPS will continue to fuel the fuser so if she has a defect, it could cause low voltage to trigger.

  I would watch just for the spark of life that says he could be alive then work outward.

• CLJ CM6040f MFP: Trainer replaced, display now turns on but the touch screen is unresponsive

  Original malfunction has been sounding like turn, but not display. Replaced the trainer, now displlay is on, but does not respond to the inputs of the touch screen. What is the sequence of corrective to fix a malfunction?

  Try this:

  http://h20564.www2.HP.com/hpsc/doc/public/display?docid=emr_na-c03559852&sp4ts.Oid=3356526

  If my post is solved your problem and click the accepted as button solution under him.

  In order to thank a Tech for a post click the thumbs up button under the post.

  You can even click on the two keys...

• HP Color LaserJet M277dw MFP: Disable auto power off after inactivity for HP Color LaserJet M277dw MFP

  What is the purpose of mobile printing solutions if you cannot activate your home printer?
  My printer stop automatically after 8 hours of inactivity and therefore makes it impossible for me to use mobile printing. The printer is connected via WLAN (without active ports to stop the closing).
  In the configuration, there are only options to stop after 2, 4 or 8 hours. No option on disabling of automatic shutdown.
  Pls do that for the people who work on the firmware updates, they must include an option to disable auto power off, many people are already complaining that and nothing has changed so far.
  Its just illogical. You make big announcements for HP eprint and other stuff, but your printers are not able to do so even if you could theoretically make eprint if your standing next to your printer all day.
  I just got this printer pluged and installed and already tired of this BS!
  I know that there is no solution, so just send it to the people who can change it.

  for all of you who read this post, I was in contact with the technical team of HP and they said that they don't give you the ability to disable auto power off on purpose, it is HPs energy-economy-policy to do and there are no plans to change this in the future
  in my case, I only WLAN's, yet is not automatically stop (although it should be), I guess I'm lucky that my router it ping every now and then and is therefore not stop
  If you can't fix it yourself with active ports and may not have at all, it will probably not option left than the back of the printer

• HP Laserjet M1217 MFP printer - error memory power

  I just install my new printer HP LaserJet M1217. I get the message "Power supply memory error" on the screen of the printer > installed the SW using the HP Smart Install program.  Win 7 is the operating system.

  Thank you very much for your help!

  Hi kongtoy,

  There is a clip on the chip on the cartridge's protective plastic. Remove the orange plastic, and he's going to quit giving you the power of memory error. Refer to figure 6

  Power supply memory error "Message is displayed on the control panel

  

• Power to the screen on the Aspire 9500

  I used a laptop Aspire 93500 with Windows XP.

  When XP retired, too, the screen started deterioratingand I gave her pension using Xubuntu Linux.

  The screen slowly surrenders, and I hooked up a spare monitor. Something to play with, but not mobile...

  Now I was given a nearly identical Aspire 9500, which was equipped with Windows 7. Slow as hell, of course.

  Now, I want to give Xubuntu as well, but I can't get the machine to boot from the DVD. It also does not show the logo Acer and startup (F2 or F12 during startup) options like my first one.

  Just try F2 or F12 stops booting with a 5 second beep about

  What can we do?

  Turn the machine off. Try to start typing F2 at the same time as you turn.

  Jack E/NJ

• LaserJet m225dn mfp pro: printer freezes up, power cord wrong or bad grounding?

  Hello.  We have an ongoing problem with this gel printer (backlight on).  I can say that it's okay if it passes in the standby mode.  If after the default, sleep, standby fails, it is always locked and requires a reboot.

  It comes with the power supply cord is too short, and relocation is very difficult.  I have been using two (seem to be very good) of the longer computer power cords.  One is 10' and the other is 12'.

  I tested the ground taken with a multimeter and it revient.2 v, which is not 0, but I think is pretty close.  There are other things on the same circuit.

  Problem is I can not test the normal short cord and easily keep the printer connected to the USB cord and a fax machine.  Would be a 10 or 12' power cord (no UPS online) will be enough to lock up this printer?   Thank you.

  I found the solution myself.  For a longer length, 14-gauge is necessary.  I have this and it seems to fix the problem.  He could have a blockage, but I'm not sure.  Been working normally for more than a week with this 15' cord

  Cable SF, universal 15 foot cord 14 AWG - IEC320 C13 to NEMA 5 - 15 p SJT 15 has

• Color Laser Jet MFP M277n Pro: Power supply flashing

  Just set up this printer.  I've not turned off because I think he's using the toner when you next turn on the.  Is this correct?  But now the power supply light flashes.  Is this normal?

  Without doubt, it entered into mode 'sleep'.  Hit the button on the screen which should come on and the power button should now be solid on.

• Laser Jet Pro M128fn MFP: Print white come & 'power attention memory' on LCD

  1. "power memory warning" on the LCD display, how to rectify this

  2 impressions come white

  Hello

  Remove the Toner Cartridge and ensure any orange sealing material has been completely removed, then reinsert the toner and try printing again.

  As reference, please see article with sampe photos:

  http://support.HP.com/us-en/document/c02484074

  Please let me know how it goes,

  Shlomi

• Laaser Jet Pro MFP M277d color: M277DW, memory error power

  How to clear a "error memory power' on my dw M277.  I use Windows 8.1.  I can't believe that HP made this for us by making us buy HP cartridges.  I guess that they do not support competition.  I'm about to junk the printer and buy another brand!

  Hello

  If please install the following firmware and check to see if that can help get the problem solved:

  http://ftp.HP.com/pub/softlib/software13/COL62137/kJ-149900-2/M277_MFP_Series_FW_Update-20150716.exe

  Be sure not to interrupt during the upgrade process.

• LJ Pro300 color MFP M375nw. Power cycling, displays "49 service error - turn off the power, then press" on-screen.

  Bike constantly, the power display "49 service error - turn off the power, then press ' on-screen before stopping.
  For this printer only when it is connected to the network. Quite happy to sit quietly when printer NOT connected to the network.

  Unplug the network cable from the printer, check and clear all print queues (there may be a doc pdf sitting in a pc or server print queue)

  Once the queues have been dotted, restart the printer and reconnect the network cable.

  If this does not cure the problem, then the likely problem is a defective formatter Board.

  Good luck!

• HP LaserJet MFP M177fw Pro: "a used power has been installed.

  When printing a 'status of supplies' black toner section displayed, "a used supply has been installed. He suggested that a not genuine cartridge has been installed. The original supplied with the printer is still installed. Not long after that the printer was new, the message of toner, said black was very low, that after only a small amount of printing.

  Any suggestions what to do?

  Hello @nigkemp

  New printers allows you to get the introductory toners that wont last long

  I guess Im a bit confused and I'm not for sure if you have 2 different toners or a single

  If it's only one supplied with the printer then replace for any new HP one and see what said with the new toner supplies

  If you do not have 2 toners (provided with the printer and another a new) then print another one supplies status page allows to call the new. Each supplies status page will give you the day to install on the toner that you want to ensure that it corresponds to the day you install the toner for the first time

  It is a way to tell if you got an original offer or society who got you might refill the toners

  Each toner has a top chip that will send the information to the unit and is how the supplies status page can get the information of

• HP LaserJet Pro 500 color MFP M570dn - manual power probe

  I AM SURPRISED THAT WITH MORE THAN 250 SPECIALISTS AVAILABLE YESTERDAY AND TODAY, NOT A SINGLE ONE OF THEM CAN ANSWER MY ORIGINAL MESSAGE IN YESTERDAY!

  Hello Experts!

  I have a new machine as described above and I have a stack of laser labels in the manual feeder.

  Whenever I have send a print job to the supply manual I need to move the paper to the printer to detect that there is a charged battery.  I can get around this problem?

  The labels are loaded in the status bar, but the message that appears on the screen is:

  * icon *!

  Manual feed.

  Simple A4

  Or press [OK] to use

  available media

  Thank you very much

  Keith H

  Looks like that Tray 1 is not configured for the paper type and size which requires the print job.

  To change the setting status bar do the following in the control panel:

  -Click the key button to open the installation menu.

  -Configuration of the system.

  -Book Setup.

  -Tray 1.

  -Type of paper.

  -Choose the type of paper you use, for example labels

  -Paper format.

  -Choose the size you use, for example, letter.

  You can also choose the Type of paper-> any Type and paper size-> of any Type, and that should take care of the prompt "press OK to use available media.