CO, redeclenchables-based synchronization

I would like to synchronize HAVE, AO and PERFORM tasks finished which are redeclenchables based on a train of pulses CO.  I've implemented a CO Pulse Freq task to run off my 9178 chassis ctr3.  The front triggered the OD to start, the falling edge triggers HAVE it and GET started.  Provided by these tasks finish are short enough, they should be redeclenchables, so whenever my CO sends a pulse they should restart.

Difficult to do this work, get an error that the task of the AI is not redeclenchables (using 9222).  Can anyone provide guidance on how to implement such a scheme?

Gracias.

Hello Telleurium,

The error you are getting is expected as the 9222 does not support the redeclenchables tasks, but shipped from the 9178 counters are redeclenchables. I suggest do you the CO Pulse Freq Output a generation over, put in place a trigger for this task, set to retrigger, and use it as the sample clock for GOT it, AO and DO. This will allow you to create a redeclenchables HAVE, AO and the ct3 your 9178 chassis-based. Examples of what I mentioned above in many places. Here are a few to get you started.

https://decibel.NI.com/content/docs/doc-6801

https://decibel.NI.com/content/docs/doc-14581

https://decibel.NI.com/content/docs/doc-4131

Best regards

Izzy O.

Technical sales engineer

National Instruments

www.NI.com/support

Tags: NI Hardware

Similar Questions

  • iBooks will not synchronize to the MacBook Pro 10.11.2 pdf

    iBooks is synchronization new folders and collections that I do. It is the manual purchased based synchronization. It will not sync all manuals and techniques pdf I have on my iPhone 6 + is my MacBook Pro el Captain 10.11.2 running or my new iPad pro...?

    This seems to be a common problem - but there must be a solution or something I'm missing... Right?

    None of the pdf files are protected. Many are created on my Mac and placed in iBooks on my phone, e-mail or online.

    IVe tried itunes sync tunes - does nothing. Ive tried to convert iTunes library and only got all of my audio books books move over, which I didn't...

    Help... This really *... As I just upgraded my storage up to 1 TB so I can finish the icloud storage switch...

    Files PDF and EPUB no ibookstore sync via the cloud, you must copy or synchronize them everywhere where you want - only ibooks (while they are still in the store and you don't move countries) will potentially show in the cloud for redownloading on your other computers/devices.

    With the phone connected to iTunes on your Mac you have tried to do file > devices > transfer purchases? If they are not purchases of the iBookstore they should copy on iTunes on your Mac, and you can then do file > move books from iTunes in the iBooks of your Mac application - if you connect your iPad to the Mac, PDF files must then show on the "books" tab in iTunes to select and sync for her

  • Download automatically added recently?

    In the music application, in 'my music' there is the option "recently added". When I type to see a list, some songs are not available offline. (They disappear when I use airplane mode.) I usually buy songs on my Mac or iPad.

    Q: How can I define which recently added songs are automatically downloaded on my iPhone?

    Thanks for any help.

    p.

    At the least, change:

    Settings > iTunes & App Stores > music [automatic downloads] = 'On '.

    Alternatively, you can consider changing the settings > music > show Apple music = "Off" and the settings > music > iCloud library = "Off" to put music on your iPhone-based synchronization.

  • Synchronization of the RIO based PCI cards

    Hello

    I have two cards PCI based 7833R with me. I would like to synchronize the two analog input cards with microseconds accuracy.could please, someone of you suggest me what is the best way to synchronize the two PCI analog input cards?

    Early response will be highly appreciated.

    -Niasse.

    Hello

    RIOCards synchronization:

    In my application,.

    • FPGA cards available: 7833R (1) and 7833R (2).

    • Card1 will act as a master and card2 will act as a slave.

    • 1 continuous square pulse of s will come from MasterCard and the same will be fed to another digital entry of the same card so card slave.

    Channel connection details for the synchronization of two maps of FPGA:

    Card1 (Box1) DIO1 must be connected to DIO2 card1 (box 1)

    Card1 DIO1 (Box1) must be connected to the card 2 DIO1 (Box2)

    • Rising edge of the square pulse is detected in the two cards. At the time where climbing aboard detected, acquisition will be launched in both maps.

    • Every minute a rising edge is detected in the two cards for the synchronization, then acquisition will be launched.

    I hope that helps!

    Kind regards

    Nicolas.

  • Comparison of files and folders based contained or binary, synchronization or merge

    My laptop hard drive died six months ago. I was able to restore some of my data from an old backup to a new drive. Recently, through the invasive recovery, I was able to recover the data structure and the file original on the old disk. Of course, the problem is that over the last six months, that the data on my laptop has changed a bit... new files, old files renamed, reorganized file structure.

    So my question is, what is the best tool of Windows (XP) to synchronize/compare/merge the recovered data with my current data as a single operation?

    File comparison tools that I have sought seem to be designed to compare only files between two directories and compare based on file name, size and date as opposed to the content of the file. I have files that may have the same content, but are now in new places or have new names from file, date/time, stamps, etc.

    File synchronization tools seem to be designed to continuously keep two directories synchronized and assume that the directory structure must be mirrored between the two locations of synchronization. I only need a single synchronization, and now, the directory structure is different.

    Essentially, I want to be able to compare all below a specified directory (for example, \My Documents) based on the content, level and ignore the name or location of the file. For in the game of recovered files that do not exist in all, I would like to be able to specify where in the Active Directory structure they must be registered. For files with identical content (but not necessarily the same location) between the two sets of data, I would like to keep in their current location in the current data set. And of course, any new data in the current data set should be retained.

    It is now discontinued, but I like Duplicate File Finder by Rashid Hoda, I think it is one of the best out there.  It's a small utility and it's very fast!  I prefer the 1.0.2.8 old version, but it becomes hard to find.   The last version was 1.1.0.3, available here: http://www.freeware-guide.com/dir/util/cleanup/DuplicateFileFinder.html

    WinMerge and FolderMatch are useful for work at the folder level, helps to synchronize files, the two great utilities.

    If you work with JPEG, you can find jStrip useful for stripping Exif and other unnecessary data in your files, it is up to you to decide if you need this additional data, but it is easier to find duplicate JPEG files when they are stripped of their parasitic data.

    John

  • Synchronize the forms with self-referential VO on the Board of the tree. POJO-based model

    Hello. I need your help

    Sample ADF Code corner #32 show how to build a picture of the tree to a self referencing VO:
    [http://www.oracle.com/technetwork/developer-tools/adf/learnmore/index-101235.html#CodeCornerSamples]

    Paper corner Code ADF Oracle JDeveloper OTN harvest/09/2011 by Frank Nimphius show how to build a form of modification of the table data and synchronize it with the selected line in the table of the tree:
    [http://www.oracle.com/technetwork/developer-tools/adf/learnmore/sept2011-otn-harvest-508189.pdf]

    These examples are useful, but I have a problem, I don't have a model based on a database, my application datamodel is based in POJO objects, there is no appModules or ViewObjects so I do not know how to reference the tree table attribute target with the iterator form edit.

    Can someone help me?
    Perhaps (I don't know how) I do a VO and an AppModule that encapsulates the model POJO?

    Thank you very much

    Hello

    It should work the same. You create a tree of a POJO data control based on your POJO model. Expose another collection pointing to the same set of data and drag it onto the form. Use the setting in the configuration tree dialog box to set the current line in the tree as aware of the iterator of form.

    Frank

  • How can synchronize photos lightroom lightroom office web-based?

    I wonder if I'll be able to sync pictures of light room based on the web for lightroom Office?  I'm new and thought that the web based one was the only one and has spent hours editing it... Now I need to burn the disc and can not understand!

    Hi carlyjophoto,

    Once you edit and save the Image on the web in Lightroom, it syncs the changes to the collection of funds as well.

    This process works based on real time

    Kind regards

    ~ Mohit

  • Redeclenchables pulse using GPCTR0 on 6062E STC

    I have the desire to have an external synchronization signal (too short a duration) detected by a jury of 6062E and output a pulse of longer duration as a timing signal that I would read on an analog channel as well as other sensors on other analog channels. I used the example program 2055.zip, STCgeneratesinglepulse, for LW/CVI as a starting point. I modified the sample program so that it is redeclenchables instead of just pulse. This code example uses GPCTR0. The program works but not as I expected. GPCTR0_OUT has the pulse output generated and programmable duration that I want. GPCTR0_GATE is the input trigger/sync signal. What I've found, is that the DOOR has a constant voltage of + 5V signal. The problem is that the only trigger that works is an intermittent grounding to the GPCTR0_GATE. I was keen to work with external synchronization signal (short signal down-up-down). I was using the DAQ card + PIN 5V power to mimic an external trigger. How can I use such a trigger signal to generate the impulse? I have included a stripped to the low, short version of the revised program sample below and also as an attachment.

    #include "nidaqex.h".
    /*********************************************************************
    * Sample program: based on 2055.zip
    * STCgenerateSingleTriggeredPulse.c //changed to redeclenchables
    *
    * Description:
    * Generates a redeclenchables digital pulse 1ms LOW and 100 ms HIGH aid
    * General counter 0 after tripping (for devices with the)
    * Acquisition of data-STC counters/timers)
    *
    * Pins of connection information:
    * Your digital output pulse will be on the GPCTR0_OUT pin (2 for 6062).
    * Connect this output to an analog channel for time synchronization w / normal DAQ.
    * Connect your trigger pulse for digital on PFI9/GPCTR0_GATE spindle (3 of 6062).
    * Plug the Locator on the ground at the 'digital ground' PIN (4 / 18 of 6062).
    *
    * To trigger, connected to pin 3 on the ground. But this isn't what I want.
    * Want relaxation to be a HIGH LEVEL of BASS. How?
    *
    * The presence or absence of next line had no effect.
    * Secret = GPCTR_Change_Parameter (iDevice, ulGpctrNum, ND_GATE_POLARITY, ND_NEGATIVE);
    *
    *********************************************************************
    * Used a second computer/data acquisition monitoring system.
    Monitoring system connected to the DAQ computer
    * ----------------------------------------------          -----------------------
    * ACH0 (68) GPCTR0_OUT (2)
    * Rider to DGND AIGND (67) (4) ACH8 (34)
    *
    * OR
    *
    * Use the counter on the second computer/data acquisition monitoring system.
    Monitoring system connected to the DAQ computer
    * --------------------------------              -----------------------
    * GPCTR0_OUT PFI9/GPCTR0_GATE (3) (2)
    * GND                                              GND
    *
    *********************************************************************/

    void main (void)
    {
    char c; for the test
    I16 Secret = 0;
    I16 iRetVal = 0;
    I16 iDevice = 1;
    ulGpctrNum u32 = ND_COUNTER_0;
    u32 ulLOWcount = 100;  1ms
    u32 ulHIGHcount = 10000; 100ms
    u32 ulLOWcount = 2;   0.02ms
    u32 ulHIGHcount = 10;  varied 0.1ms for testing
        
    Secret = GPCTR_Control (iDevice, ulGpctrNum, ND_RESET);
    Secret = GPCTR_Set_Application (iDevice, ulGpctrNum, ND_RETRIG_PULSE_GNR);
    Secret = GPCTR_Change_Parameter (iDevice, ulGpctrNum, ND_SOURCE, ND_INTERNAL_100_KHZ);
    Secret = GPCTR_Change_Parameter (iDevice, ulGpctrNum, ND_GATE_POLARITY, ND_NEGATIVE);
    Secret = GPCTR_Change_Parameter (iDevice, ulGpctrNum, ND_GATE, ND_PFI_9);  Gate, apply trigger here
    Secret = GPCTR_Change_Parameter (iDevice, ulGpctrNum, ND_COUNT_1, ulLOWcount);
    Secret = GPCTR_Change_Parameter (iDevice, ulGpctrNum, ND_COUNT_2, ulHIGHcount);
    / * To print a counter pulse, you must call Select_Signal. */
    Secret = Select_Signal (iDevice, ND_GPCTR0_OUTPUT, ND_GPCTR0_OUTPUT, ND_LOW_TO_HIGH);
    Secret = GPCTR_Control (iDevice, ulGpctrNum, ND_PROGRAM);
    printf ("apply your trigger pulse to PFI9 now. \nThe rising edge is armed and the second falling edge is in the value. \n") ;
    c = GetChar (); This simulates normal DAQ.
    Secret = GPCTR_Control (iDevice, ulGpctrNum, ND_RESET);
    / * Note that the following call to Select_Signal causes the
    output high impedance that will probably bring the logic
    HIGH level, if there is a pull-up on this PIN resistance. (Check your)
    Manual of equipment.)  If you do not want this behavior, comment
    the next line. */
    Secret = Select_Signal (iDevice, ND_GPCTR0_OUTPUT, ND_NONE, ND_DONT_CARE);
    return;
    }

    S_Hong,

    I solved my problem.

    I had in my code

    iStatus is GPCTR_Change_Parameter (iDevice, ulGpctrNum, ND_GATE, ND_PFI_9);.

    and was my trigger for entry. This is false because PFI_9 is an echo out of everything my trigger is connected to.

    I changed the statement to

    iStatus is GPCTR_Change_Parameter (iDevice, ulGpctrNum, ND_GATE, ND_PFI_0);.    for the source of the signal.

    and now a trigger on the PIN PFI_0 generates the impulse.

  • Advice to synchronize two computers on one account

    I want to omit a certain user (account) when I sync my new laptop... so it

    only fill with all financial data (for example) my Bill based

    pay the user account on the new computer. Anyway to do in icloud

    using a single account? Or dropbox is better for this kind of 'user account '.

    exclusion"syncing?

    Thank you.

    JUD

    Simply synchronize the account that you want to synchronize with iCloud by using this specific Apple ID.

  • Used to synchronize 160 GB...

    I connect it, it shows "sync", but a second later iPod says OK to disconnect without having disconnected me. I can't deal with it seriously.

    This is normal, if iTunes does not updates to sync with the iPod.  You say expect you changes (e.g. new songs) to automatically sync with iPod, but they do not have?  If so, you should check how music from iPod settings screen is set up in iTunes.  If it is not currently set to sync music, the iPod shows it is "sync" (when connected), but nothing syncs.  To do this, what you have described.

    Click on the button of the iPod in iTunes.  The screenshot below shows the left upper corner of the window of my iTunes, with device button circled in red.

    Settings of the iPod summary screen.  Along the left side of the window, in the sidebar, under settings, click on music.  Parameters of music from the iPod screen to the right, where you tell iTunes how to sync songs to the iPod.  Check the box to Sync music.

    NOTE: If this box is not already checked, and check it out you now, all the songs on the iPod that are not in iTunes on your computer, library will be lost.

    This enables automatic synchronization.  Below, if your music library can fit on your iPod, you can choose to synchronize the entire music library.  Otherwise, you can choose to synchronize some lists of reading, artists, albums and genresand make selections from the list below.  Click apply.  Go ahead, iTunes automatically updated iPod when you connect (or click sync , if already connected), based on how you set up this screen.

    If this isn't the problem, please post back with more details about your situation.

  • used to synchronize nano

    Used to synchronize nano 4 GB.

    Cannot add or remove music nano via a computer usb port to nano!

    Based on this limited information, it is difficult to guess at the real problem.  Here is some basic info, that can help...

    In current iTunes, click the button on the device to access settings of recapitulation of the iPod screen in iTunes.  Here is a screenshot of the upper left corner of my iTunes window, showing an iPod button (circled in red).  Click on this button.

    On the settings of the iPod summary screen, it has a sidebar along the left side of the window (below the tiny image and the name of iPod).  In the sidebar, under settings, click on music.  Settings of music from the iPod screen is shown at right.  If you expect that iTunes to automatically sync music when you connect iPod, check mark the box to Sync music.

    NOTE: All songs currently on the iPod that are not in iTunes on your computer, library will be lost.

    Then, set up this screen to tell how to automatically sync songs to iPod to iTunes.  Click Apply to sync.  Further, iTunes automatically updated iPod (when you connect or click sync , if already connected) with changes to the iTunes music library, based on how you set up this screen.

    If you want to manually load (and remove) songs on iPod, back on the settings of the iPod summary screen, checkmark the box for manually manage music and videos].  And apply.

    Please post back with any specific questions.

  • Needs of synchronization forced to replace send and receive or else everything will not amount to a merger. When can we expect these features?

    I used Sync in the browsers chrome based and had to leave because he managed the synchronization in the same way as this. He did the meaning of thought, that it merges. What ultimately happens is all browsers that connects to it will have its settings and bookmarks scrambled.

    Please add forced Send and Receive with capacity of replacement as well as total manual operation.

    You can provide here that the reactions of Mozilla:
    https://input.Mozilla.org/en-us/feedback

  • confused about downloading messages and synchronization

    I'm new to TB - in the past, I always used a simple web interface. My server is on a server (Dreamhost) IMAP

    I read "Options of Configuration for Messages to download" page, but either do not understand or it does not give enough detail.

    I want to download all my messages stored on my server for my laptop, not only the headers. I want to retain the existing configuration of file I have on my server. I don't want TB never remove any message unless I tell it to do, preferably with confirmation.

    My goal is to download all my currently stored electronic records, and then once I know that they are safe on my hard drive I'll selectively delete them from the server.

    I do not understand how TB do this. It seems it only downloads the headers, and I don't see how to download the entire message. In addition, I don't want to quite what I think considers synchronization - if I delete a message on the server I don't want necessarily TB to remove this message locally. Otherwise, how could I check my messages locally?

    in other words, I want that all my messages stored locally, and only some of them left on the server.

    For example, I put three emails in a folder on my server. I left who
    connection, then call Icedove on my laptop. If I click on this file, it
    then retrieves and displays these three emails (or only the headers?).

    If I leave Icedove in my web based e-mail and delete these
    three emails from the server, I would expect these three emails to stay on my
    local computer. Yet when I invoke Icedove once again, he sees three emails are
    disappeared from the server and subsequently removed from the display.

    So, this means that the messages were never really recovered
    locally? Or Icedove Deletes local copies to synchronize
    with the server?

    Here are the settings I use:

    under "Copies & folders"-> archives message keep in: "archive folder".
    "On": local folders.

    under 'Synchronization & Storage'-> 'Message synchronization'-> keep
    messages for this account on this machine. I have all the files audited
    under "Advanced".

    under "Disk space"-> synchronize all messages regardless of age. And
    'Do not delete all messages '. It does not give me an option to not use
    synchronization.

    Thanks if you can help.
    Keith

    Matt-thanks a lot!

    Your info really helped. This is what worked for me:

    Right-click local folders, and then create local folders to match those on the server.

    All folder to online server, select, ctrl + A to select all of the messages, right-click for the drop-down menu "copy", then copy them in desired local folder.

    Once I did, I also went through the selected server files, ctrl + A to select all, then click on "Archive", which offers the mail on the server in the Archive, sorted by date of the year. It was scary at first because I didn't know they would not display until after Icedove has restarted! United Nations-Linux very like, but I think not uncommon in the world of Windows.

    So I found myself with two copies of most of my mail - in a local folder and the other in the Archives. What is good for a few MB of messages I have.

    I will mark this as resolved issue.

    Thanks again!
    Keith Ostertag

  • I can't get the sync music figurentsur MAC function when you try to synchronize itunes for iphone iOS 12 9

    When I open itunes with my iphone plugged in, does not display the page where I can choose to synchronize the music - it shows, it's the ability to synchronize the voice memos, no music - please help!

    https://discussions.apple.com/thread/7163823 - if you subscribed to Apple music or iTunes game, you will not have to run manually or synchronize music on a device in iTunes. Synchronize your music is made by iCloud and all of your eligible music should appear there. Movies can always be synchronized.

    A little more on this subject and a few options - https://discussions.apple.com/thread/7194995 and: move content from iTunes on your computer to your iPhone, iPad or iPod touch

    - https://support.apple.com/en-us/HT201593

    and a workaround - https://discussions.apple.com/message/28842873#28842873

    If you haven't signed up for one of the iCloud based services:

    https://discussions.apple.com/message/28481661#28481661 - "synchronize your music changed in iTunes 12.2.0 and iOS 8.4 music App."

  • Muliple USRP RIO 2943R, synchronization and phase-locking problem

    I use 8 USRP RIO 2943Rs transmission of signal and receving (4 for Tx) and 4 for Rx I'm using the "signal-based" method for synchronization of all devices. And I did it. I tested the system the result is very interesting:
    1. when I put the sampling rate of less than 40MS/s IQ, I can obversve very good phase locked Tx and Rx signals (I use a sine wave CW for tests), please refer to video joint (locked 40MSs)
    2. BUT, when I put the IQ more than 60 MS/s sampling rate, I'll lose phase lock. Please refer to unlocked 60MSs. My goal is to run the system at 120MS/s
    I have doubt as to if the problem comes from two sides:
    a. the sync methed isn't fair
    b. OR, should I increase the clock that operates the loop 'In Streaming radio engine' in the FPGA VI. as shown in the following image.

    I would like to ask experts in the forum to discuss the solution of this problem.
    More information about my system setting:


Maybe you are looking for

  • Opening still works with iOS 10?

    I use Aperture 3.6 on a MacBook Pro with El Capitan 10.11.6 and was planning to upgrade my iPhone to iOS 10 6.  But I have been burned by problems with previous upgrades before (for example when opening disappeared from the App Store for a period of

  • Satellite Pro P300 - 13 M - how to replace the network card?

    Hello I have the Satellite Pro P300 - 13M. My sister fell on my UTP cable and so he was taken out by force and because of that "holding-pings" on the front of the port are bent or broken, so whenever I put in a cable with traction slightess or accide

  • Satellite A200 - 10 X: how to set up Toshiba media buttons

    Sensor Board with two regimes has 3 buttons to open some applications.I have coordinated these buttons with some applications... But now I need to put other applications.This function seems to be so useful! I tried to find this information in the man

  • Enabling hardware virtualization significantly slows the W530

    I enabled hardware virtualization in the Security tab in the BIOS of my new W530 that running Win 7 Pro 64 bit. This has slowed the machine so badly that windows is now open to a series of slow shakes. I would like to turn on hardware virtualization

  • before the safe mode

    I thought my computer had a problem with a recently installed program. I started to look around for a fix and stumbled upon the restoration of the system. I went from there by clicking on safe mode. I am now in safe mode and everything is different.