Codec of Tandberg C series - DVI - I adapter

Similar Questions

• Codec of Tandberg C series - DVI - I

  Hi guys,.

  I'm trying to understand the DVI ports on a codec C60. I need to connect a VGA (from PC) input and an Hdmi output (on a plasma screen). I can only find vga-vga cables and hdmi to hdmi cable (good quality).

  I want to know what type of DVI/VGA and DVI to HDMI adapter that I need to buy. DVI - I ports on the codec.

  For the vga cable should I buy an adapter DVI - A, even a vga DVI - I adapt, just not a DVI - D adapter?

  For the hdmi cable should I buy a hdmi to DVI - D, even a DVI adapter - I adapt, just not a DVI - A adapter?

  Is the corect above or not?

  Thank you

  Silviu.

  > Cable vga should I buy an adapter DVI - A, even a vga DVI - I adapt, just not a DVI - D adapter?

  OK, you can use a VGA-to-DVI-I (or VGA-to-DVI-A), but also have the choice to use the VGA-DVI-I cable (or a VGA-DVI-A cable) that could have more choices with lower price.

  > Cable hdmi should I buy a hdmi to DVI - D, even a DVI adapter - I adapt, just not a DVI - A adapter?

  OK, DVI - D or DVI - I adapter works for your installation, but you can use the HDMI connection on the monitor directly, without conversion DVI-HDMI.

  Please note that some of the coded C-series has several interfaces of HDMI output and you may need to change the configuration of role of display to the first or second monitor.

  =======================================================

  xConfiguration video output HDMI 1 OverscanLevel: None

  xConfiguration video output HDMI 1 EAC Mode: Off

  xConfiguration video output HDMI 1 MonitorRole: Prime

  xConfiguration video output HDMI 3 resolution: Auto

  xConfiguration video output HDMI 3 OverscanLevel: None

  xConfiguration video output HDMI 3 EAC Mode: Off

  xConfiguration video output HDMI 3 MonitorRole: second

  ======================================================

• Using the Codec C90 Tandberg T1 with CUCM

  Hi all

  is it possible to register the Codec C90 a Tandberg T1 to the CUCM?

  We are currently trying to save one, but the State of the record is still "failed: 485 ambiguous." The CUCM tells us that the record is rejected. Is it possible that the problem is the product ID, which is "Cisco Telepresence T1". We can only select C90 Cisco CUCM on. If it does not, and the device is rejected.

  Is there a way to fix this? Perhaps saying the C90 is therefore more a T1? We have already tried to remove all optionkeys, but there is a 'unknown' type which cannot be deleted. Could this be the key T1?

  I hope good answers :)

  Kind regards

  Jannik

  Looking at the matrix unit CUCM package compatibility, TANDBERG T Series end points are not supported, IE: are not.

  If you do not want to use the codec C90 T1 of the TANDBERG itself and not the Q1 as a whole, you may be able to change the product key for the T1 be a C90 asking new license keys.  See t3-c90-codecs.

• will be series 1 watch watches series 2 bands adapt?

  will strip of Apple Watch hermes I bought for series 2 series 1 adapt?

  Hello

  Yes - all the bands of Apple Watch Hermes will be adapted to any Apple Watch of the same size of the case (42mm or 38 mm).

  To clarify, series 1 does not refer to your existing, first generation watch. He referred to a new Apple Watch model that has the same characteristics as the original Apple Watch, with the exception of a new dual core processor.

• DVI/VGA adapter.

  I have a HP110-122el PC and I just bought what I thought, it was a VGA DVI adapter. The DVI adapter part again has 24 pins and a connector spade and 4 extra pins, 2 above and 2 below the pod. The socket on my tour takes the casings for these 4 additional points. Therefore, the adapter doesn't fit. Are there different types of DVI adapters or is my weird PC?

  HI Hookey,

  Image (blur) below shows the types of DVI connectors.

  

  Your description of your adapter indicates that your have a DVI - I dual-link adapter.  The socket on the PC's DVI - D (digital only). If your monitor is analog, then use a straight VGA cable without adapter. Your PC is not strange that most, if not all new HP PC are DVI - D (digital only).  You can see the specifications for the HP 110-122el here.

  By your other post, your monitor specifications are here.

• On V6302AU (V6000 Series) wireless network adapter

  I had no problem with my front wireless (and run wireless of my sister is not the network).  Now, when I turn on my computer the wireless signal turns blue and the icon says he's working.  However, my computer does not recognize all wireless networks.  The Windows Network Diagnostics indicates that the computer has an installed and configured wireless network adapter.  I've uninstalled and reinstalled the driver wireless lan broadcom for vista on the compact site, but that did not help.

  Can anyone help?

  Thank you

  TC

  I took my computer to my friends shop, sent it to HP and they replaced the part.  It took a few weeks and cost about NZ$ 80.  Problem solved.

  Take it to a professional!

  TC

• Adapter VGA DVI - HP 3500 Pro

  Hi all

  Recently, my boss bought a bunch of HP Pro 3500 s. They come with a VGA and DVI, port that we use both for a dual monitor set up. Now when we connect to these ports by using a VGA cable and DVI set up works very well. However, when we use a VGA DVI adapter DVI port, the second monitor is not detectable. Is there a way to solve this problem, so we can use the adapters? Any suggestions would be greatly appreciated.

  Thank you

  SJ Wolf

  You use the built-in ports in the mobo?
  One is other vga and dvi?
  Is the port dvi - d (digital) dvi or dvi - i (ntegrated) - see wiki:
  http://en.Wikipedia.org/wiki/Digital_Visual_Interface#connector

  Sorry for so many questions, but I can't find a document for this pc that displays the ports - just this one:
  https://h20565.www2.hp.com/portal/site/hpsc/template.BINARYPORTLET/public/kb/docDisplay/resource.process/?spf_p.tpst=kbDocDisplay_ws_BI&spf_p.rid_kbDocDisplay=docDisplayResURL&javax.portlet.begCacheTok=com.vignette.cachetoken&spf_p.rst_kbDocDisplay=wsrp-resourceState%3DdocId%253Demr_na-c03550750-1%257CdocLocale%253Dde_DE&javax.portlet.endCacheTok=com.vignette.cachetoken

  If the port is dvi - d adapter-dvi2vga does not work...

  C.

• j5create usb dvi for monitor flat screen display adapter

  I received a box that popped up when I was installing a usb to dvi display adapter model jua230 on my windows xp pc. He said I need to check compatibility and check to see if it passed the windows logo test. Is it okay to install on my computer? I'm trying to fix a flat screen to a processor that does not have a dvi port. The warning said that it could possibly cause problems for the computer in the future.

  Thank you for your help.

  Hello

  The message seems to be due to the fact that manufacturing had not their WHQL certified driver. The device driver can still install and the device might work. The message is a warning that the driver has not been tested.

• C - Series codecs update the firmware of the device PHD 720 p

  Hey there everyone,

  A question that I think I know the answer to, but it would be good to get confirmation.  As we know, if a doctorate 1080 p camera is connected to a codec of the C series, when a software update is applied on the codec that includes an update of the firmware of the camera, the camera is upgraded once the update to the codec is completed.

  The same will happen if a doctorate 720 p camera is attached to the C Series codec instead?  I do not, but it would be good to get confirmation.  First tests showed that it will not.

  Thank you!

  Hi Bob,

  You're right, it will not.  Series package C does not contain the software of the camera for the 720 p camera, and no improvement will happen.

  For 720 p and 1080 p camera camera firmware are different.

  Teck Chye

• Tandberg MCU 5300 series supports the Conference me the feature?

  Hi all

  I would like to know that the 5300 Tandberg MCU series supports the Conference me the feature?

  We checked the 5320 MCU data sheet,

  Cisco TelePresence MCU 5320 CTI-5320-MCU-K9

  Comes with: 5320 - MCU and cables - MCU ports must be enabled with optional port licenses

  Software for Cisco TelePresence MCU 5320 license options

  1 nHD full HD/2 HD/4 SD/8 ports on 5320 MCU (max 10 with this option (6 used for nHD)) LIC-5300-4PL

  Second option Ethernet port (VFO) for the MCU 5320 LIC-5300-VFO

  AES and HTTPS option for the MCU 5320 LIC-AESMCU53-K9

  However, there is no information related to Conference me function.

  So, can we know everything that Tandberg MCU 5300 series supports the Conference me the feature?

  Best regards

  Ben

  Hi Ben,

  Conference is not compatible with the MCU 5300 series.

  Best regards

  Markus

  Sent by Cisco Support technique iPad App

• C60 DVI input 3 Auto Detect using a DVI to VGA splitter

  Hello

  We install a codec C60 using a splitter DVI input n ° 3 for the presentation source (DVI - I male to DVI - D & VGA Splitter cable's female adapter)

  The DVI input source is configured as Auto-Detect.  Administrator's Guide confirms this seting automatically detects the signal is analog (VGA) or digital (DVI or HDMI).

  The problem is the codec can't really switch from one source to another.   We do not seek to send two signals at once, but rather stable wether VGA and HMDI will be detected by the codec according to the entry sends the laptop.

  can anyone confirm if this is a limitation of the codec, or bug in firmware or even simply impossible without adding additional hardware.

  see you soon,

  Mel

  Hello

  Yes, auto-detection works for me.

• UNIT III NTSC TANDBERG camera cable pinout

  ALCON,

  Someone at - it a reference document that describes the pinout of the cable and the cable part number for the old TTC-6 not TTC - 7 (MXP6000) connection of codec to TANDBERG UNIT III NTSC (analog) camera?

  Any help would be appreciated.

  VR

  Chet

  Hello Chet,

  Here is a link for the Tandberg MXP user guide

  http://www.Cisco.com/c/dam/en/us/TD/docs/Telepresence/endpoint/MXP-serie...

  At page 262, you will see the list of the pins out of the 6000MXP codec and 302 page gives you the pinout of the Wave2 camera entry.

  Hope this helps

  Steve

• Video signal splitter unrecognized DVI - two different devices! Why?

  Looking for answers - replaced a motorized DVI splitter that has worked well for over a year - using HDMI > DVI

  adapter to connect Mac Mini i7 2012, OSX 10.8.5, HDMI port, to the Aluratek DVI splitter.  Configuration below - worked fine for about 2 weeks.  Then came after a few days of inactivity - computer but the display mode 'sleep'... would not wake up. removed the splitter and connected live - monitor (s) work well.   This same issue is why I replaced a divisor of model "TrippLite" - impeccable/no questions for 12 months, and more with this one.    The separator indicates its getting the video signal from the Mac... and video shows displays connected... but see monitors/don't receive it no signal.  I tried to lower the display resolution - no impact.  Have reset NVRAM, SMC several times... reconnected, the range cable several times... tired MiniDisplay Port Adapter > DVI... no luck.  ANY IDEAS MUCH APPRECIATED!  It's in a studio where I need to have dual - in a second workspace - splitter necessary because the distance to the extreme-monitor is too long for a splitter - liabilities

  Technical support said mfgr this Mini graphics card can possibly work for "a while" then stop recognizing the defendant of... How do I?  If we read a single monitor, directly - connected is too much coincidence for a second separator developed the same problem as the other we had - I don't know if there is some thing in the Acer monitor settings that would have an impact on anything whatsoever but I doubt - this new separator 'fixed' the old man a problem after it was connected - and now signal is not recognized through it after a few weeks.

  

  If you have a multimeter, check voltage on his block of POWER & with 2 will check for a ground loop...

  https://en.Wikipedia.org/wiki/Ground_loop _ (electricity)

• Using DVI instead of VGA on the Port Replicator - Tecra A9

  I have a port replicator toshiba that I use with my laptop Tecra A9, currently I have a vga cable to run the external monitor, but I prefer to use DVI instead, but I can't make it work.

  Is there a setting somewhere that I have to activate? or should it work?

  See you soon

  Ash.

  Hello

  As much as I know there nothing that you must set for the use of the DVI port. The question is how you use it. Using a DVI - VGA adapter?

• Apple cinema display DVI HDMI naar

  I have a monitor cinema display with DVI and Firewire USB 2010. I want to connect it to a generation of 3rd apple tv. A DVI HDMI adapter works for this?

  Thanks in advance

  Maarten

  I'm not 100% sure but I don't think it will work, the cinema display monitor is 16:10 so be deformed but if that was the case.