Color LaserJet CP1025nw: printer does not print after changing cartridges

I just inserted cartridges M, Y and C in my printer.  They are official cartridges 126 a.  I followed all the instructions (shook gently, removed the orange protective cover and pulled the Ribbon out).  I inserted one at a time, waiting after each insertion for the printer to run through its cycle.  Then I tried to print a color print job with no luck.  Then I tried to print a simple typed page - once again, no luck!

Is it possible to print a test page?  I don't get any messages on my computer.  When I look at the print queue, it says "error printing".  Help, please!  Thank you.

Note later: my mistake!  I turn on the blue light from the top; Once lit, the printer has been good to go.  Can tell you that I'm not very technologically savvy?

So it works very well now?

Tags: HP Printers

Similar Questions

  • Pavilion dm3-2020eo does not start after change of RAM

    As the topic says my computer does not start after a change of the RAM.

    I've updated 2 x 2 GB 2 x 4 GB DDR3 SO - DIMM 204pins Rams. When I start the computer after installing new RAM does nothing, all I get is a black screen.

    According to the Spec computers, it should be able to take up to 8 GB of DDR3 RAM.

    Can someone help me?

    Thank you
    Leo

    Here's the key:

    We're working on two sockets and one does not at all.

    You have a bad memory module. It happens very rarely, but it's not impossible to get a new stick of bad memory. Get the replaced bad and I think you'll be fine.

  • color laserjet cp1025nw print streaky

    I get entrelardé & dirty my HP Laserjet CP1025nw color printing.

    Have executed the impression several times cleaning process without success.

    This just happened. He perfectly managed so far.

    Hello newoboz,

    Welcome to the Forums of HP Support!

    After reading your post, I see that you have the LaserJet CP1025nw and it is poor quality printing. Run the cleaning of the printer will usually clear up problems.

    I was able to locate this HP document: print quality problems, it contains 11 steps to help solve this problem for you.

    I hope this helps, let me know if it does not work.

    Kind regards

  • HPDeskjet 3070 DOES NOT PRINT AFTER CHANGING CARTRIDGE.

    After changing all four cartridges in printer Deskjet 3070, is no longer prints black, produced a blank sheet on the copy function and will only print jpg files, this happens with the Dell laptop on USB or network, also Dell laptop computer on the network (not tried USB). The printer worked perfectly before the change, on the site of consumables HP HP cartridgesare. This is the third change of cartridge (HP, always) since the purchase of the printer in November 2011, they appear in the last four months.

    Hello JohnFo

    So the color is printing, but not black? What happens if you make a color copy by using a black text word document? I suggest as a result of the article below. It contains troubleshooting steps for the white pages. If the problem persists check the next few sentences.
    Printer prints white sheets of paper

    The problem could be a bad cartridge. Before working on the printer as the article suggests you should contact HP. All authentic HP ink cartridges come with their own warranty, so if you call HP on the cartridge, you should be able to replace to help determine if the cartridge is the problem.

  • printer does not work after changing equipment

    I have problems with my computer and we determined that it was the motherboard.  We have installed a new motherboard, the new switch, second hard drive, the new keyboard and now my printer is not working correctly.  It prints half the line and text and does not correctly read the row format.  gives extra space, etc.

    Furthermore, none of my PDF read correctly.  Yes, I have the latest version of adobe.

    The game, 16 February 2012 17:22:14 + 0000, asured wrote:

    I have problems with my computer and we determined that it was the motherboard.  We have installed a new motherboard, the new switch, second hard drive, the new keyboard and now my printer is not working correctly.  It prints half the line and text and does not correctly read the row format.  gives extra space, etc.

    Have you installed the driver appropriate for the printer?

    Furthermore, none of my PDF read correctly.  Yes, I have the latest version of adobe.

    Adobe is a company, not a program. Do you mean Adobe Reader? If so,.
    What is unsuitable for the way it reads?

    Also, I strongly recommend to move from Adobe to the free Foxit Reader
    Drive to http://www.foxitsoftware.com/Secure_PDF_Reader/ I think there
    much better than Adobe Reader.

    Ken Blake, Microsoft MVP

  • HP Color Laserjet 3600n: door does not close

    There seems to be something in the way that prevents the door from closing completely.  I switched all cartridges and transfer belt.  It seems there have broken anything inside.  Because the door does not close, it won't initialize.

    Any ideas?

    Thank you for your ideas, but he wasn't a cartridge problem.

    I hired an eyes of co-workers and she found a white tab in the upper left corner that hung down unlike our other 3600 s.  When he was pushed upward, all broken in the door completely closed.

  • Purchased in UK/Oz apps does not refresh after changing store in the USA.

    I was in the United Kingdom and Oz and had a UK or OZ account and bought apps - they updated very well (although never automatically as promised).

    Now, I moved to the United States and updated my account to USA store.

    The apps I bought previously refreshes (much).

    If I click on an app in the store I, iTunes think I haven't it and install it.

    Does anyone have the same problem and the solution? I fed it to Apple.

    On a latest operating system Mac and iTunes.

    Before changing countries make sure that you have downloaded and saved all your previous country store purchases.  You will not be able to re - download it again once you change of country and it won't be easy to change the country to another once you lose your mode of payment for the old country (such as a waiting period).  As long as you have on your computer you'll be fine.  You also will be able to update all the apps that you have purchased.

    Change your iTunes Store country or region - https://support.apple.com/HT201389 - "After changing the country of your account, you won't see what you bought the previous country store in the purchase section."

  • HARD does not work after changing the disk partitions recovery media creator

    Hello world

    After installing windoows 8.1 April major upgrade (win 8.1 presents as OEM), and have shrunk C partition to create a data partition "D", "Troubleshooting" option under advanced start menu is no longer available.

    Toshiba Recovery Media Creator does not work, too (it can not find any hard disk recovery partion).
    I got in the OEM recovery partition.
    I am also able to create a recovery using the Windows tool unit.
    You have no idea about it?

    Thank you very much!

    Hello

    Sorry to hear about all this. Unfortunately, you now have a big problem. I don't understand why you didn't create support of recovery before you started to change the factory settings, including to change the structure of the partitions of HARD drive.

    Mobile offered with factory settings a structure specific partitions and recovery recorded image is saved on the partition of drive specific and marked with invisible markers. These markers are visible for preinstalled Toshiba recovery media creator tool and when you start the tool can find points of reference and has full access to specific files.

    Unfortunately, after changing the original scores structure Toshiba tool cannot find these markers more and is not able to copy files from recovery media recovery. What you need now is the original recovery disk. Using this disk, you can install original recovery image and after doing this, you will have new factory settings.

    I know it sounds stupid now but you must order the original recovery disk and it can be done on https://backupmedia.toshiba.eu/landing.aspx

    If you have any other questions you are welcome.

  • Tecra A3 does not work after changing the power settings

    I changed my power settings in my tecra a3 laptop and now it does not start correctly. wants to start but just keeps going back to press F2 or F12 it please help.

    Hello
    where did you changed them? In the BIOS or in the Toshiba HW setup?

    I suggest you go into bios after turning on your machine. You have to hit just F2 Ant then in the search for bios for setting "all default setting" or something with "bios setup defaults" to reset your bios settings.

    After that, your computer should start up again.

    Welcome them

  • Tecra S3 - Intel PROSet/Wireless window does not respond after changing settings

    Given that I've updated the driver and the utility Intel PROSet version 9.0.4.17 driver and tool PROSet to version 10.5.0.1 for Intel BG2200 WLAN card to build-in the PROSet tool window freezes every time after that I changed a parameter (for example, by adding a new profile).

    Closing the window with ALT - F4 also does not work unless you kill the process in Task Manager.

    Is this a known problem or is there any group of fixes for the driver or the Intel PROSet tool available?

    Hello

    The ProSet utility is a clean product Intel and if there are updates you find on the Intel Web site.
    But in my opinion, there is only a corruption of installation.
    How do you install this app? Have you removed the old version first?

    I think that if you want to update the programs, you must always first remove the old version and then after reboot of the new laptop, you can begin the installation of the new version.

    You could use additional own program register as a CCleaner. It s a freeware application and it checks the registry for some corruptions.

  • gSynchit does not open after changing the password

    GSynchit has stopped working. I changed the password of email account, but the program does not open if I can change the settings.

    Hello

    1. what operating system do you use?

    2. What mail client do you use?

    3 did you receive an error message when you try to run gSychit

    If you use windows7, I suggest you follow the link and check.

    How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7

    http://support.Microsoft.com/kb/929135

    Note: After a repair, be sure to set the computer to start as usual as mentioned in step 7 in the above article.

  • 160 U does not start after changing from 4 to 8 GB Ram

    Hey community,.

    I just installed two new RAM DDR3 1066 MHz 7-7-7-20 204pin modules of Corsair SO-DIMM to improve my U160 somewhat. It runs a Win 7 Pro 64 Home and already has been improved with a Samsung 250 GB SSD.

    The BIOS indicates the RAM properly but no matter if I try for a normal start or economy mode, restarting the laptop once the windows colors appear when starting. 'Last known version' does not help, nor let him start via a bootalble pen which I also installed this version of Windows. Because there is no blue or black screen I guess it's not a physical problem, but a prob of victory.

    Someone an idea?

    Thanks in advance,

    Baschdel

    Maybe run mem test a bar at a time to see if its bad? run the test of mem on a USB drive or a bootable cd. Lenovo is known to support only a certain amount of ram, I guess to avoid problems and complications. It is not their problem if you exceed nominal max and it does not work.

    http://www.memtest.org/

  • My copy registered and checked for XP Pro SP3 does not start after changing the motherboard. Second problem is that I can't find my original install of XP Pro disc.

    After failing to find the source of reliable performance from my PC, I decided to bite the bullet and replace the motherboard, memory and the CPU. I installed a triple base 435 Athlon and a motherboard Gigabyte MA74GMT. Awarded PC again started the first time - but Windows will not, I get a number of options but none work - safe mode brings up several lines of messages on the partition of multi (0) disk (0) rdisk (0).

    A previous post suggested that a similar message meant some kind of malware but if I replace the old motherboard, processor and memory Windows works very well - in fact I use it now.

    Do I have an option but to reinstall Windows from a CD? Otherwise I have a problem - I can't find the installation discs for each piece of software except my Windows XP Pro! I do repair discs?

    Thanks for your help.

    Hi DaGeLi,

    · Provide us with the complete message you receive.

    Follow the methods below:

    Method 1:

    You were able to start the first time, you can try to boot to the last known good configuration and check the results. Link to get the procedure please refer to: how to start your computer by using last good known Windows XP Configuration:http://support.microsoft.com/kb/307852

    Method 2:

    If it doesn't then you can follow the procedure from the below mentioned link. As you do not have the Windows XP CD you can follow the procedure if you have already installed on the computer to recovery console

    How do I recover from a corrupted registry that prevents Windows XP startup:http://support.microsoft.com/kb/307545

    Otherwise, you may need to make the boot floppies. See the link for the procedure below:

    http://support.Microsoft.com/kb/310994

    You can also contact the manufacturer of the system to get the Windows XP CD.

    For reference: how to fix a computer that does not start:http://www.microsoft.com/windowsxp/using/setup/support/nostart.mspx#2

    With regard to:

    Samhrutha G S - Microsoft technical support.

    Visit our Microsoft answers feedback Forum and let us know what you think

  • HP Photosmart 3210: I can't close the top of my hp3210 printer after changing cartridges

    After changing a few cartridges of my hp3210 photosmart printer I can't close the top, there is something blocking

    This youtube video can be useful: replace the ink cartridge

  • OptiPlex 755 USFF does not start after changing the cmos battery

    I have a desktop Optiplex 755 USFF requiring the cmos battery to replace. After the replacement of the computer will not start. It brings up the menu windows start, the sasfe mode, safe mode with network set mode command prompt, security, last know good configuration and boot normally. Any option will bring to the top of the WIndows XP loading screen and then re-boot of the computer right back to the start screen. A big loop. I can get the hard drive to boot in an Optiplex GX280 without problem. I was told of the motherboard needs to be replaced, but I changed the units of the system and the same thing with this hard drive.

    I tried to reinstall the operating system and get all the way to "starting windows" and then the blue screen stop error message 0x0000007B (0xF7A10524, 0xC0000034, 0x00000000, 0x00000000) dead. The computer is WIndows XP SP3, 1 GB of ram with 80 GB hard drive. It seems that the Setup program does not recognize the hard drive.

    Any help would be appreciated.

    After several hours of experimentation, I finally found the correct BIOS settings in order to get the computer to boot. There are three BIOS settings that need to be changed or check settings by default so that it can work. SATA 0 must be activated, SATA operations must be changed from AHCI, ATA and in the modular Bay, by default "far-sighted" should be replaced by the IDE. Save the settings and start the computer to the right upwards.

  • Windows7 - error msgs & MGP works does not properly after changing drive letter

    I am running Windows 7 Home Premium 64-bit.

    When first, I partitioned my HARD drive, the 2nd logical drive was labeled J:, who was the next available letter after all the optical drives and integrated flash memory readers.

    I prefer to label it D: (to follow immediately from the boot partition which is C :).  I used the functionality of disk management to change the drive letter of the J: to D: (and of course move the rest optical drives and integrated flash memory ready in 1 letter).

    When I run some programs, I get this error message:

    "There is no disk in the drive. Insert a disc into drive \Device\Harddisk4\DR4.

    Options click below this message are "Cancel", "Try again" or "continue".

    Some programs, such as Google Chrome, Microsoft Works word processor and spreadsheet, clicking on one of the 3 options will allow the program to operate normally.

    For other programs, such as Windows Live Movie Maker, clicking options will cause a "Drive not ready" message and lead to more problems.  For example, I can not load my existing projects, because I can't get to the screen that allows me to navigate through drives and folders to choose my file.

    I uninstalled and reinstalled the Movie Maker, but the problem is still there.

    Seems to me that it is not the individual programs that are at the origin of the problem, but something in Windows 7 itself.

    How can I get rid of the error messages and get the programs to run normally?  Do I have to edit the registry of Windows 7?  If so, what will exactly be changed?

    Thanks in advance.

    Think I found the answer.  Looks like it is a problem of registry after all.  That's what I did:

    (1) go to the start menu.

    (2) execute Regedit by typing "regedit" in the search box and press .

    (3) the search for "J:" in the whole registry.

    (4) when a directory path is starting by 'J' and the pursuit of my familiar subfolder names, I should now start with "D:" instead, I right click on it, choose "Edit" and change the "J" to "D".  (Note: I only change to directory paths that looked familiar to me and I'm sure that should now start with "D:".)  I change all instances of "J:" that were found).

    (5) once this is over, choose 'File', then 'leave '.

    A ran programs that have already given the error message.  No error message comes this time.  Restarted the PC and programs run.  Once again, no error message.  I hope that things stay effortless.

Maybe you are looking for

  • need stop synchronization before finishing to avoid ipod classic remove

    I've updated to itunes version 12.5.1, as well as Windows 10.  If I let my ipod classic finish syncing, everything on the ipod is removed.  So I have to restore the ipod in disk mode so that itunes recognizes the ipod and avoid itunes gel settings. 

  • iPad Pro PPT mirrored glitch?

    iPad Pro connected to projector (lightning / vga) will reflect the PPT presentation. If you click on a URL and show a video YouTube then back to the presentation that the connected display will remain frozen on video. Go to the home screen and return

  • Photos does not, any more than iPhoto

    Photos, which worked yesterday, will suddenly be open are not not iPhoto. I restarted several times and tried to open while pressing the command option. Nothing. Help!

  • How to locate the window Task Manager

    I have a problem to locate my Task Manager window on my window XP desktop. pls help. Thank you.

  • How can I upload files to the mesh instead of skydrive storage storage space

    Windows Live Mesh + Upload Skydrive I have just been enabled for Windows Live Mesh and enjoyed. Extremely useful. Great job Microsoft. Keep it up and I can be influenced to get a Windows Mobile phone. My question concerns the Mesh and Skydrive integr