Color LaserJet MFP M277dw Pro: MFP M277dw unable to connect to wifi

Similar Questions

• Color Laserjet MFP M277DW Pro: scan to pdf corrupted

  I use Nitro PDF, and every time that I scan to PDF it is said the first page was damaged and has been repaired.   But it is empty, no content on page 1. This will happen if I use the shipper of record or the screen.  I just bought a new laptop, and there was this problem on my old laptop as well.  Scan to JPEG works but then have to take the extra step to convert the JPEG to PDF and it's a hassle.  Why the first page is always corrupt?

  Hello

  Do you have installled of Adobe Reader on your PC? (even if not used as the default viewer)?

  As you can find the system requirements below, it is part of the configuration required to make full use of the printer:

  http://support.HP.com/us-en/product/HP-Color-LaserJet-MFP-M277-series/7089945/model/7089949/document/c04515051/

  Try to install it starting from the following link, then try to scan the image:

  http://get.Adobe.com/reader/

  Now try to open the file with Nitro PDF, if the same persists check if you can see a difference with Adobe Reader.

  Shlomi

• HP Color Laserjet M277dw MFP: Cannot scan HP Color Laserjet MFP M277dw on Mac OS 10.6

  Hello, I can not scan to network drive using the above mentioned printer. Scan to USB key is possible.

  I downloaded the update (version 20160331) firmware image, but impossible to install the program. After double click, nothing happens. Any ideas?

  Thank you and best regards

  Christoph

  Hi Christoph,

  The printer is not compatible with Snow Leopard, it is supported on Lion (10.7) or later versions.

  You can find the system requirements below:

  http://support.HP.com/us-en/product/HP-Color-LaserJet-Pro-MFP-M277-series/7089945/model/7089949/document/c04515051/

  The update of the firmware utilitywas not desinged for your operating system and therefore does not work on it.

  As the connectewd printer to a network, follow these steps to update firmware directly from the menu of the printer:

  http://support.HP.com/us-en/product/HP-Color-LaserJet-MFP-M277-series/7089945/model/7089949/document/c04517106/

  If the implementation of scan to a shared folder on your grave down Mac, please specify the exact error, and the parameters used (path of the shared folder used, etc.) also well done you have shared this folder your Mac form?

• Color LaserJet MFP M477fdn Pro: M477 Software Installation fails at 99%

  Like others who have posted here, I have been unable to get the printer software to complete the installation. The printer is a Color LaserJet Pro MFP M477fdn, 3 months. I'm trying to install the software on a new workstation HP Z240 performing Windows 10 (64-bit). The connection is via USB cable. The printer and the software have been previously used with a Windows 7 machine without problem.

  I tried, repeatedly, to install the software from the disc supplied with the printer and also a 126.6 mb download HP Color LaserJet MFP printer M477 Pro series full software and drivers. The results are the same with a source - installation apparently progresses up to connect it the indicator product of progression from screen reached 99%, how it gives an error message "a Setup operation took too long to run. It is a fatal error, preventing the use of the product. Restart your computer and run this installer again. If the problem persists, please visit the web site of product support for your product. "It takes about 20 minutes for the phase of installation to go from 0 to 99%, and then later hooked up to 99% for 2-5 minutes, the error message is displayed.

  I am able to print to this printer, but at least do not have the ability to scan from the computer there is no indication that the I.R.I.S. OCR software is installed.

  I had care of do not connect USB until you are educated.

  I tried repeating the installation without uninstalling first and get the same result.

  I used the uninstall contained the disk feature, and have deleted the printer to the computer using the Panel between the installation attempts.

  I tried to do a right click to run the installer as administrator and get the same result.

  I tried to install after clean boots with turned off Windows Firewall and all functions of the software Norton Internet Security including its function of firewall turned off.

  The event viewer displays none error entry at all and no entry identifies HP as the source of an event.

  I tried to connect via USB 2.0 and 3.0 ports.

  I cleaned recycle them and temporary folders.

  I have updated the firmware of the printer to the 20160331 version.

  Printed printer configuration report will not display any errors, nor that the printer itself indicates something is wrong and confirms the update of the firmware.

  I deselected the optional software, the devices experience HP and I.R.I.S. OCR, trying to install only the required files two more program scanning HP.

  Thanks for any help solving this.

  I think I understood the question, 10 windows installs its own driver, and the installation program expects the hp driver to install.

  DO this FOR THE HP INSTALLER PROCESS (when the percentage meter goes)

  1. go into the Device Manager and find the printer in the list of devices

  2. right click on the printer and select "Update Driver software"

  3. click on "Browse my computer for driver software".

  4. choose "Let Me pick one...» »

  5. Select the named driver: HP Color LaserJet MFP M477 PCL-6 Pro (make sure it's one with a dash between the pcl and 6!)

  6. click next and back to the installation of hp box and must now see the printer and continue the installation.

  -Alex

• Color LaserJet MFP M277 dw Pro: Setup disk gives an error and stops before the connection to the printer

  Hello

  I try to install the printer 'Color LaserJet MFP M277 dw Pro'.
  By inserting the disc into the phase "installation preparation" is 96% and then stops and gives me the error.
  I use Windows XP SP3. It is always installed, but physically disconnected another printer hp (hp 2050).
  (I tried both to disable the antivirus that reduce to a minimal install, but the problem persists).
  Thank you

  Response thanks a lot.
  In the meantime, I contacted the Support of the Italy
  Who suggested that I try to update the driver.
  I downloaded the file "HP_LaserJet_M277_PCL6_Legacy_Print_Driver_14295".
  Automatic extraction and I launched and everything seems to work.
  (I still try to scan and fax if they work).
  Thank you very much.
  Thanks to your colleague Michelle with whom I chatted.
  Contact thank you for the support of Milan that I don't know the name.
  So, I can communicate the solution found.

• scan to email on Color LaserJet MFP M177fw Pro

  I'm trying to download the printable 'Scan to Email' on my Color LaserJet MFP M177fw Pro, but he continues to throw an error?

  When I bought the printer (yesterday), I was told that I could put up to Scan in a document and have it automatically send as an e-mail message to a recipient.  How to achieve this?

  Thank you!

  Hi grahammccarthy,

  Welcome to the HP Support forums.  I understand that you want to know how to scan to email using your printer Laserjet Pro MFP M177fw.

  You don't mention the operating system that you use, so I've included links to all the operating systems supported on the way to analyze.  There is a section called "How to scan with HP software" and there you can find a subsection entitled "How to scan to email.  It is in the subsection, you will find the instructions you need to follow to be able to scan to email.

  How to perform a scan: Windows XP

  How to perform a scan: Windows Vista

  How to perform a scan: Windows 7

  How to perform a scan: Windows 8

  How to perform a scan: OS X v10.8

  How to perform a scan: OS X v10.9

• Color LaserJet MFP M177fw Pro: Scan to Mac with Color LaserJet MFP M177fw Pro

  I bought and the latest drivers from hp installation a HP Color LaserJet Pro MFP M177fw. are downloaded and installed.

  I have a Mac and you connect wirelessly to the printer, which works very well. The Mac runs Yosemite 10.10.3

  My question is the digitization. There is no option for scanning anywhere, not on the small screen of the printer not on the usefulness of the printer or any where.

  Summer spend hours online to find an answer and is now well bored.

  I have already reset the disc printing, verified and repaired systems. Can not scan even with the options offered on the forums of hp using Apple caprure or preview. It seems that all these options include versions of OS X prior to Yosemite?

  I buy a multifunction printer that is not scan? I said to the saleswoman that I need a printer that can scan and airprint...

  Is it possible to scan to a mac at all with this printer? Any help?

  Hi @sa9494,

  I see that you have problems with scanning. I will definitely do my best to help you.

  Check the name of the driver that is installed by the printer. Make sure that it shows just the name of the printer.
  Click on the Apple menu, click System Preferences. Click on Printers & Scanners, highlight the name of the printer on the left side and right side of the screen it should show the name of the printer. (Color LaserJet MFP M177fw Pro)

  If the full name of the printer is not correctly, delete and add the printer name back from the list. Click on the sign - to remove the driver and then click on the + sign to add the driver might have to drop-down list to select the name of the printer to add a click.

  

  

  Here is a screenshot of what it should look like. You have the scanning through top tab?

  

  I have also included a document for HP printers - scan with HP Software in OS X v10.10 Yosemite.

  Scanning ports is not open on the router to the origin of this problem. You can contact the router company to verify and to open these ports 9220/9500/427 on the router.

  Connect the printer with the USB cable, to see if you have the same results.

  Let me know.

  If you appreciate my efforts, please click on the "Thumbs up" button below.
  If you have any questions, please let me know what steps you have taken and the results. Thank you.

• Color LaserJet MFP M177fw Pro: Color LaserJet MFP M177fw Pro

  I have Color LaserJet MFP M177fw Pro and it is stuck on print fax. I restart the printer and print the fax even. I found a post and supposed to go ware closes so I did. Printer is returned to normal. Got another fax and the printer to print fax. I tried firmware ubgrade once again without help. Toolbox program HP device says 'Printing Fax Page 1'

  Also I can't receive any new faxes and print to the device.

  Hi @DDTKS.

  Welcome to the FOrums of HP's Support. I understand that your Laserjet M177fw is stuck to print a fax. I would like to help.

  I sent you the steps to perform initialization of the NVRAM via private message.

  If you are unfamiliar with the operation of the function of private messages of the Forum, this posthas instructions.

• Color LaserJet MFP M177FW Pro: 126 a Toner can be used with Color LaserJet Pro MFP M177FW?

  I recently bought a Color LaserJet MFP M177FW Pro and still have 126 a toner cartridges (magenta, cyan and yellow) for my LaserJet MFP M175 precedent. I can use them rather than the cartridges of 130a recommended?

  Hello

  Only 3 printers can use HP 126 has:

  http://WWW8.HP.com/us/en/products/OAS/product-detail.html?OID=4148379#! tab = compatible_hosts

  Kind regards.

• color laserjet MFP M177: error message when you try to print

  Hello

  I have a HP Color laserjet MFP M177.  I can't print I get an error message on my computer screen. No messeage shows up on the printer.  I have recently upgraded to windows 10 (I do not know what version) If this could have something to do with it?

  Help, please

  Thank you

  Hi @Daisy001,

  Welcome to the Forums of HP Support! I see by your post that you can't print, since the upgrade to Windows 10. I will definitely do my best to help you. If this helps you to find a solution, please click on the button "Accept as Solution" down below in this message. If you want to say thanks for my effort to help, click on the 'Thumbs Up' to give me a Kudos.

  If you have not completely uninstall and reinstall the driver, I would say to start it there first. Here is the link to the latest drivers: Color_LJPro_MFP_M177_full - solution_15188.exe

  If the problem persists, you can download and run the print and Scan doctor, he will diagnose the problem and could solve it automatically.

  Please let me know the results and if there is anything else I can help you. Thank you.

• VAIO SVE151G13W unable to connect to WIFI.

  VAIO SVE151G13W unable to connect to WIFI.

  All other PEDs connect, but not my laptop. All tracks to fix it please. Indication on the bar of legal status at the bottom is a yellow triangle with an exclamatory mark that says internet connections are available. But, I cannot open any page on the net.

  Hello ACM,.

  You can try to open the firewall settings and make sure that your browser is not blocked. You can also try reinstalling your browser or use an everything to a new fact to ensure like google chrome. It will be useful.

• HP 15-ac152sa laptop: wifi tab disappears from the network settings menu. Unable to connect to wifi

  I bought a new laptop. I connected to the WiFi network with no problems the first time. I have downloaded Microsoft office 2016 (home and student). The next time I turned on the laptop, the icon WiFi in the corner of the screen says "no connection available.

  On the tab "network and internet". There is no tab for WiFi. Initially, I managed to fix it by clicking on the 'network card', 'properties' and on the 'power management' tab, I unchecked the box indicating "allow the computer to turn off this device to save power. This fixed the problem... until the next time I turned on the laptop. It's the same thing and I am unable to connect to internet via WiFi.

  The single adapter in the list here is "Realtek PCI-e FE family controller #2". Still unable to connect to WiFi... Still no WiFi tab under settings "network and internet". Help, please!

  So, the problem was finally solved (fingers crossed!).

  Yes, the Internet access worked perfectly every time when it is connected through the Ethernet cable. Ultimately I phoned the helpline. They checked for the new driver updates (these have been already updated), restored the BIOS remotely and then restored the device to the factory settings. Start of the fault still took place intermittently. This indicates a hardware problem, and the unit was sent for repair.

  The idea was that when the WiFi did not work, the WiFi card wasn't physically visiable in the list of available adapters, nor has the Bluetooth adapter. Apparently in this device, the Bluetooth and WiFi functions are on the same network adapter and apparently those elements should not disappear from the list of available adapters. So the fact that they disappeared together intermittently indicated a hardware problem with the card.

  Now that I got my laptop back and I think that the WiFicard has been replaced. Hoping all is well now and I hope this post helps someone else.

  Thanks hp for fast and wonderful customer service.

  Sarah

• HP Color LaserJet MFP M277 Pro: No software or drivers are available for HP Color LaserJet Pro M277dw MFP

  Trying to download the latest drivers (I couldn't scan with Easy Scan more after the release of macOS sierra 10.12) I received the following massage

  http://support.HP.com/us-en/drivers/selfservice/HP-Color-LaserJet-Pro-MFP-m277-series/7089945/model/...

  No software or drivers are available for this product with the selected operating system. Please make a different selection, or visit the product home page.

  PS: My OS has been identified correctly in the web page.

  Hi @pisca46,

  Thank you for joining the HP Forums!

  I understand that there is no drivers for your HP Color LaserJet Pro MFP M277dw on Mac OS X 10.12 Sierra. I am pleased to see that for you!

  You are right that there are currently no drivers available at this time. In the meantime, I suggest trying the rest of this guide, of install a printer Mac driver by using Apple Software Updateand then try using the Apple Image Capture.

  Otherwise, all we can do is wait for the drivers and software provision, or plan to use an older version of Mac OS X.

  If it helps, please consider clicking on "accept as a solution." And, please click the thumbs up icon. The two icons are below this post.

  I hope this helps!

• MFP M277 dw: Color LaserJet MFP M277dw Pro issues with iMac

  I have a 2015 21.5 "iMac running El Capitan (10.11.3) and a HP Color LaserJet Pro M277dw MFP that falls in offline mode when it is idle for a while.

  Once the Mac has been sleeping, I can no longer copy, scan or fax without having to restart the printer and the iMac. And it is intermittent. This does not happen everytime the iMac goes to sleep, but no doubt it happens once or twice a week.

  The printer is connected both wireless (so that I can print from my iPad in other parts of the House.) and directly to the iMac via USB.

  I have updated all the HP software related and have applied the last update of the HP firmware for the printer as well. I also ran through all the game instructions that were provided with the printer.

  Other troubleshooting tips would be greatly appreciated.

  Hi @RBurgett,

  Thanks for joining the Forums of HP Support for a solution to your fall issue offline printer.

  I understand you have a HP Color LaserJet Pro MFP M277dw connected to a wireless network for your iPad and connected with a USB to your iMac running Mac OS X 10.11.3 El Capitan, but the drops of the printer is offline after has been idle for a while and becomes also insensitive after mode "Eve". I would like to help with that.

  If you see the message on the printer offline on the iMac, it would be because the iMac think he's using the wireless printer, when it should be using the USB connection.

  You should be able to solve that by unplugging the USB cable. Once the USB cable is removed, reset the Mac printing system. If you don't know how to reset the Mac printing system, here is a document of support that can help - reset the printing system.

  After printing Mac system has been reset, you should be able to reconnect the USB cable and add it to printers and Scanners.

  As far as being not able to copy, scan or fax without having to restart the printer and the iMac that could be solved by resetting the printing system and making sure the USB printer is listed in the printers and Scanner. When the printer seem to be insensitive, the first step is to perform a reset of the power on the printer.

  

  Please let me know if that solves the problem, or if you need assistance.

• HP Color LaserJet MFP M277 Pro: LaserJet MFP M277dw announces its own wireless network

  I just installed a new HP Color LaserJet M277dw MFP Pro and noticed that it creates its own network wireless with the name ' HP-Setup > LaserJet 5 c-277. Even if the WiFi is turned off.

  I don't want the printer to make her presence known on WiFi and would like to know how I can turn this 'feature '.

  What is this function? I couldn't find any information about this in the manual, nor any of the settings of the printer where the name ' HP-Setup > LaserJet 5 c-277 "appears.

  @seron

  Ok...

  Try changing the Direct wireless / activate - or combination is necessary to turn the setting and the close up with the 'off' setting / disabled.

  In other words, no matter what the setting, Direct wireless can light up.

  Leave a few seconds between the time where as you toggle the setting.

  If that does not hit on it free, toggle the setting and then turn the printer off for about 20 seconds and then turn on the printer.

  When you see a post that will help you,

  Who inspires you, gives a cool idea,

  Or you learn something new.

  Click the 'Thumbs Up' on this post.

  My answer-click accept as Solution to help others find answers.