Color LaserJet Pro 200 M251 nw: unable to do manual duplex printing with Windows 10

Similar Questions

• 79 Service error on Printer series color LaserJet Pro 200 M251

  I use this printer with the operating system Mac OSX 10.9.4 for about 9 months.

  Now, I get an error message from the Service 79. I tried to turn off the printer and the several times without success.

  Curiously, when I try to print a document, a message keeps appearing on my computer that says "the printer has been suspended. You want to resume printing? "When I click on the button resume, nothing prints.

  The manual States that the 79 Service error message is related to a firmware issue? Do you know how I can fix this problem?

  Thank you very much

  Stone

  Hi NebraskaPierre,

  By your post, I see that you have found a Service 79 error on the printer. I can help you.

  Make sure that the printer is connected directly to a wall outlet. (do not use a hub or a surge protector) This ensures that the printer is full on and can help this situation.

  This can be caused by malformed PostScript documents.

  Follow these steps:

  Locate the power switch on the bottom of the printer.
  Turn the printer off position and COUNT to 10.
  Turn on the printer and the system should be all together.

  Try printing from another application to see if you have the same problem.
  
  If a print job from your hand repeatedly causes this error, this may indicate a problem with the print job.

  Try to split your document upward more before they print it.

  Fix permissions of the drive on the Mac:

• Color LaserJet Pro 200 M27nw MFP - problem scanning ADF

  Seems to me a new Color LaserJet Pro 200 M27nw MFP running on a PC with Windows 8 and have come to realize that whenever I scan from the ADF Document (CAD), no output file is generated. The original document is drawn in by the document successfully feeder and the printer display indicates that the scan is ready. However, no analysis file is generated. This happens regardless of know if I send the output to USB or to e-mail and if the original document leaves simple or multiple.

  Interestingly, the ADF works fine if I try to produce paper copies, in other words, the printer is able to pull in the leaves o FRENCH original of the document in the ADF (as this either alone or several sheets) and to produce copies of the original successfully. Furthermore, I have no problem to scan multiple or single sheet documents when the original document is loaded by the Scanner flat, rather than the document feeder Scanner.

  Appreciate any help. Thank you

  Stephen

  HI @StephenScerri ,

  I see by your post that when scanning from the ADF there is no output file containing the scan which is generated on USB or e-mail. You can copy the ADF and scan successfully of the bucket. I would like to help.

  Is this printer the Pro 200 M127nw MFP Laserjet

  I have provided a document for how Scan: Windows 8

  When you scan from the magazine, you get an overview of the analysis of the computer software?

  What is the scan preview, but do not save it to the computer?

  What software are you using to scan?

  Try saving the scan on the computer, if you get a preview, to see if it will save the scan it.

  Please provide detailed results if you're still having problems.

  Have a great day!
  Thank you.

• M251nw color LaserJet pro 200: does print in black only, no color

  All of a sudden, my m251nw color laserjet pro 200 prints only black. Cartridges changed (C/M/Y) without modification. Toolbox shows that they are all 100%, but nothing will be printed in color, not even the Demo Page. Anyone able to help?

  Updated the firmware from hp, and it fixed the problem.

• LaserJet Pro 200: Impression of dark color LaserJet Pro 200 m251nw

  I recently bought and installed a printer of Color LaserJet Pro 200 and have noticed that when I print anything either in the color of the image is very "dark".

  When I print the example page, via the touch screen, the image seems very bright and vibrant. However, whatever it is printed via my computer throug h that an application is dark with almost oversaturated colors.

  I downloaded and installed the most recent driver from the HP site and nothing has changed. The printer is connected wireless to the home network and I tried not directly connected to the computer at the moment.

  Any suggestions would be greatly appreciated.

  Hello

  In the Printing Preferences screen (click Properties or settings of the print dialog box in the application used to print to access printing preferences screen), try disabling the HP EasyColor option in the color tab.

  Also try to select the themes of different colors like photograph (sRGB) or Photo (Adobe sRGB).

  You can see any difference with the results then?

  Shlomi

• Color LaserJet Pro 200 M251n: LJ Pro200 M251n not print not some font sizes

  My new printer does not print text to certain sizes of fonts using Word or Publisher 2010. Until 60pt, it's good, but not 72, 100, or 120. However, it will print 240 pt. It will also display these text elements of the pdf document.

  Is this a driver problem? I use PCL6 but cannot find any drivers on the HP site. Do I need UPD PCL 6?

  Hello

  Update the latest firmware for the printer, which should solve this.

  Use the next tool if it is connected with a USB key:

  http://ftp.HP.com/pub/softlib/software13/COL44532/LJ-108129-8/M251_color_Series_FW_Update-20150212.exe

  For a network connection, follow these steps:

  http://support.HP.com/us-en/product/HP-LaserJet-Pro-200-color-printer-M251nw/5097632/model/5097639/document/c03341482

  Kind regards

  Shlomi

• Color LaserJet pro 200 M276nw MFP - Scan configuration and installation on Mac Yosemite

  Hi all

  I just bought a new LaserJet pro 200 color MFP M276nw and I am trying (for 4 days) to coorectly install it.

  My goal would be to use it via the wifi connection and I put it correctly by the façade.

  When I try to install the printer on wifi, I can install the printer driver, but I can't find the driver for scanning.

  I tried to connect by ethernet and the system to emphasize a multifunction scanner and the printer driver. If use them, it works correctly.

  Whenever I go out the lan cable for use in wifi it lose the scan functions.

  What I am doing wrong?

  Thank you

  Gianluigi

  Hi @gianluigi1982 ,

  I see that you have problems with scanning via the wireless network, but you can scan through an Ethernet connection.

  I would like to help.

  Do you have what drivers installed the printer? (Apple update or the 10.9 download drivers)

  I checked our laboratory with 10.10 installed on this computer and I was able to browse for printers and Scanners on the wireless network.

  Check the version of the driver installed.

  Go to the Apple preferences system, printers, and Scanners, highlight the Laserjet printers, click the print tab on the right side of the window, and select the Options and supplies.
  Under the general tab it will give the list the version of the driver.
  19.9 is one on the lab.

  Which driver you have show?

  Check the name of the driver that is installed by the printer. Make sure that it shows just the name of the printer.
  Click on the Apple menu, click System Preferences. Click on Printers & Scanners, highlight the name of the printer on the left side and right side of the screen it should show the name of the printer. (MFP Laserjet Pro 200 M276)

  If the full name of the printer is not correctly, delete and add the printer name back from the list. Click on the sign - to remove the driver and then click on the + sign to add the driver might have to drop-down list to select the name of the printer to add a click.

  In the printers and Scanners window, highlight the printer on the left side, to the right of the window, you should have a print/scan tab, click Scan, and then open Scanners and test scanning. If you do not have the scan tab, let me know.

  

  Have you added the printer as your Hello or via the IP protocol? (cannot scan through the IP Protocol)

  You use the automatic IP address or your own static IP address?

  Here is some information for scanning in OS X v10.10 Yosemite without software HP.

  Please provide detailed results if you're still having problems.

  Good day!
  Thank you.

• M276n MFP: HP color LaserJet Pro 200 M276n multifunction

  Hello

  I recently bought color HP LaserJet Pro 200 M276n MFP. I face a problem with fax reception when it goes into sleep mode. Consider for automatic reception, but after an hour the fax does not work and sometimes I have to reset it. I use it for my office. whenever I should to wake up but the Knight, he makes is not possible.

  Thank you very much

   

  Hello

  Try to install the latest firmware for your printer from the link below:

  http://FTP.HP.com/pub/softlib/software13/COL44533/kJ-108130-7/M276_colorMFP_Series_FW_Update-2015021...

  Here's one of his describedenhancements, in my view, that it should solve the problem:

  Addresses an issue where the device may not wake up from sleep mode when receiving a fax if it is connected to an improperly grounded 220v power source.
  

  Please let me know how it goes,

  Shlomi

• HP color laserjet pro 200 m251n reset

  my printer hp laserjet pro 200 color achieved m251n adjustment locked after I attribute to use smart installation of the system. but I didn't put a password before. I can't cold reset for this type. Please help me...

  Hi robydj2007,

  Sorry about that. I'll send you a PM.

  Thank you.

• Color HP Laserjet Pro 200 M251: HP Laserjet Pro 200 M251nw print pdf with OffBeat foot

  Printing documents PFD with the quirky footer al the way to the top.

  Print the pdf as image only pages, then the foot rest where it belongs.

  Hi @Martinkoopman,

  Welcome to the Forums of HP Support! I see when you print pdf documents to your HP LaserJet Pro M251nw Color it prints with the footer moved all the way to the top.  If you print as an image only it remains where it requires.

  1. what program you are using to print PDF files from?

  2 have you tried to update the program?

  3. this happens in all programs or just one?

  I would like to run you HP print and scan doctor > www.hp.com/go/tools- it was designed by HP to offer users troubleshooting and characteristics of fix needed to solve many common problems experienced with HP print and scan the products related to Windows computers.

  What are the results? I'll watch for your reply.

  Thank you for being a part of the community of HP. Please let me know if this helps solve the problem by marking this message as "accept as Solution". If you need more assistance let me know and I will gladly do whatever I can to help. If you want to say thanks for my effort to help, click on the "Thumbs up" to give me a "Bravo".

• Multifunction Color LaserJet Pro 200: blue line when scanning from feeder not dish

  When I scan from the charger, I get a blue line that spans the length of the document. It does not happen when I scan from the tray. any suggestions on how to fix?

  Thank you

  Hi @Pichopop,

  Welcome to the Forums of HP Support! I read your post and see that you have found a blue line, during the analysis from the ADF. I will definitely do my best to help you. If this helps you to find a solution, please click on the button "Accept as Solution" down below in this message. If you want to say thanks for my effort to help, click on the 'Thumbs Up' to give me a Kudos.

  What is the name and the product number of your printer? How can I find my model number or product number?

  There are several models of Laserjet 200 series.

  Make sure that the printer is connected directly to a wall outlet. (do not use a hub or a surge protector) This ensures that the printer is full on and can help this situation. Poor power connections can cause problems of copy and scanning and rejection of the toner.

  Here is a document for the cleaning of the glass and Platinum. You will notice that there are two areas for the glass, one for the dish and the other is for the ADF.

  • Copies, faxes, or Scans have Vertical black and white lines to the exit.

  Do not take into account the model and the title. Proceed to step three: clean the glass and Platinum sweeping.

  Please let me know the results and if there is anything else I can help you. Thank you.

• HP Laserjet Pro 200 M251 color: what makes edges control average under preferences

  My other question has been resolved so quickly, I thought I would ask another

  What does the control edge under preferences?

  Thank you

  Lisa

  page 49 of the guide available here M251UserGuide

  

• Color LaserJet Pro 200: Scanner unavailable

  Ever sinc update the firmware on my printer, I had two problems.  The first problem is that the power button is now flashing after a prolonged peiord of inactivity.  I cannot print unless I push the power button flashes and it becomes solid.

  The biggest problem is that now I can't scan.  I get an error message after "the Scanner is inaccessible.  Scanner communication cannot be established.  Make sure that your product is running... »

  I am able to print once I hit the button and it stops flashing.

  Guess my first question is, is I possible to revert to the previous version of firmware.

  Welcome to the community of HP @ab90011,

  I saw your post on communication issues scan your 200 Laserjet is having, and I would try to help! You will not be able to return to a previous firmware version.

  If your printer is connected to a network, try power cycling network devices:

  • Turn off the printer and the computer and unplug the router for 1 minute (do not press the buttons on the router).
  • Plug the router back in and wait another minute, turn on the printer and the computer.
  • Try to scan the image.

  Tip: Make sure that the printer is plugged directly into the wall, avoiding bars power and surge protectors.
  

  If it is from scanning, run the print and Scan Doctor and choose "scan of difficulty."

  Answer to me with the results of the PSDr tool, how you have the printer connected (Ethernet, wireless, USB), and LaserJet 200 model you have.

  Thank you

• Color LaserJet Pro 200 M251nw: bad Color Laserjet Pro 200 M251nw print quality

  Hello

  I've owned the above printer for 1 month and for the first two weeks, it worked fine. On his return from a week leave. When I now print the image resembles what I can only describe as if someone has dribbled water down causing the toners to face each other.  I cleaned and followed all the troubleshooting of things without success. I also checked the toner drums and they appear fine. Any help would be appreciated as I now seem to have a printer expensive usless

  Thank you

  Alan

  Hi @Al24,

  I read your post and see that when printing now, the image looks as if someone has dribbled water down causing him the toners to face each other. I will definitely do my best to help you.

  You use Genuine HP Toner?
  What are the levels of toner?

  Make sure that the printer is connected directly to a wall outlet. (do not use a hub or a surge protector) This ensures that the printer is full on and can help this situation.

  Run the printer calibration.
  On the configuration of the system key touch printer, print quality, color calibration calibrate now.

  Print a diagnostic Page to see if you have the same results. Trying to determine if it is a hardware or software problem.

  Go to Setup, reports, arrow down and select diagnostic report.

  

  I have a document with several steps to run a clean and check the settings of the printer driver.

  Troubleshooting print quality problems.

  Make sure the paper type is selected and no paper said.

  Check if the drum unit for damage:

  1. remove the cartridge of toner product and check that the tape has been removed.
  2. check the memory chip for damage.
  3 examine the surface of the imaging drum on the bottom of the toner cartridge.
  CAUTION: Do not touch the roller (Imaging drum) on the bottom of the cartridge.

  His fingerprints on the imaging drum can cause print quality problems.
  4. If you see the scratches, fingerprints, toner or other damage on the imaging drum, replace the toner.
  5. If the imaging drum does not appear to be damaged, rock the toner cartridge gently several times and reinstall it. Print a few pages to see if the problem is resolved.

  The test pages come out the same?

  What kind of paper do you use?

  If you appreciate my efforts, please click on the "Thumbs up" button below.

  If there is anything else I can help you, let me know. Thank you.

• MFP Color Laserjet Pro 200 print menu

  When I use my iMac 27 with this printer, I see all the print options in the print menu in preview, etc that are mentioned in the User Guide.  No 'color/quality' options / advanced etc. to change.   I downloaded and installed the latest drivers from HP.  I use OS X 10.9.4.  Am I doing something wrong or missing something.  The product works very well otherwise.

  Hi jerryoster,

  It seems to me from your description that you use the Mac AirPrint driver instead of the HP driver. I suggest the following;

  Reset the printing system

  1. Click on the Apple icon ( ), then click on System Preferences.