Color LaserJet Pro 200 M251nw incorrect location

An incorrect location for the printer M251 will affect app availability, technical support options, and a few other things frustrating. The LCD touch screen is a little wonky on the first Setup, and we accidentally chose a different country of our desired first config entry. Applications available in the connected site hp corresponding to the location set in place on the printer.

This is different from the language selection. Even if we had the correct language selected, the printer reported itself to be in a different country of actual usage.

There is no parameter of the web page of the printer and not reset will eventually ask or allow you to change the code.

Solution to be posted then.

To solve this problem (and potentially other set incorrect configurations), it must first make a backup of the configuration of the printer. This is done through the web pages of the printer, on the System tab, and then save and restore in the left navigation pane.

Once the file DeviceSave.xml is downloaded to your computer, open it in your text editor or XML editor. Attention, bad parameters in this file could cause problems with your printer configuration. Proceed with caution!

In the final stanza, finding the


Change to the

enabled

Just add the word licence between the tags. * NOTE * there should be no space between the dd: and the DeviceLocation. This editor to please to do an emoji on this combination and it looks like this ddeviceLocation. Probably best to do not copy / paste the above lines.

Save and close the file. Back in the web pages of the device, on the backup/restore page, under load and restore the settings of the device, select the file comes to edit and click on the Load button. The printer should immediately ask the location of the country.

Good luck. Calibrate the touch screen. Make a new backup.

Tags: HP Printers

Similar Questions

  • LaserJet Pro 200: Impression of dark color LaserJet Pro 200 m251nw

    I recently bought and installed a printer of Color LaserJet Pro 200 and have noticed that when I print anything either in the color of the image is very "dark".

    When I print the example page, via the touch screen, the image seems very bright and vibrant. However, whatever it is printed via my computer throug h that an application is dark with almost oversaturated colors.

    I downloaded and installed the most recent driver from the HP site and nothing has changed. The printer is connected wireless to the home network and I tried not directly connected to the computer at the moment.

    Any suggestions would be greatly appreciated.

    Hello

    In the Printing Preferences screen (click Properties or settings of the print dialog box in the application used to print to access printing preferences screen), try disabling the HP EasyColor option in the color tab.

    Also try to select the themes of different colors like photograph (sRGB) or Photo (Adobe sRGB).

    You can see any difference with the results then?

    Shlomi

  • Color LaserJet Pro 200 M251nw: bad Color Laserjet Pro 200 M251nw print quality

    Hello

    I've owned the above printer for 1 month and for the first two weeks, it worked fine. On his return from a week leave. When I now print the image resembles what I can only describe as if someone has dribbled water down causing the toners to face each other.  I cleaned and followed all the troubleshooting of things without success. I also checked the toner drums and they appear fine. Any help would be appreciated as I now seem to have a printer expensive usless

    Thank you

    Alan

    Hi @Al24,

    I read your post and see that when printing now, the image looks as if someone has dribbled water down causing him the toners to face each other. I will definitely do my best to help you.

    You use Genuine HP Toner?
    What are the levels of toner?

    Make sure that the printer is connected directly to a wall outlet. (do not use a hub or a surge protector) This ensures that the printer is full on and can help this situation.

    Run the printer calibration.
    On the configuration of the system key touch printer, print quality, color calibration calibrate now.

    Print a diagnostic Page to see if you have the same results. Trying to determine if it is a hardware or software problem.

    Go to Setup, reports, arrow down and select diagnostic report.

    I have a document with several steps to run a clean and check the settings of the printer driver.

    Troubleshooting print quality problems.

    Make sure the paper type is selected and no paper said.

    Check if the drum unit for damage:

    1. remove the cartridge of toner product and check that the tape has been removed.
    2. check the memory chip for damage.
    3 examine the surface of the imaging drum on the bottom of the toner cartridge.
    CAUTION: Do not touch the roller (Imaging drum) on the bottom of the cartridge.

    His fingerprints on the imaging drum can cause print quality problems.
    4. If you see the scratches, fingerprints, toner or other damage on the imaging drum, replace the toner.
    5. If the imaging drum does not appear to be damaged, rock the toner cartridge gently several times and reinstall it. Print a few pages to see if the problem is resolved.

    The test pages come out the same?

    What kind of paper do you use?

    If you appreciate my efforts, please click on the "Thumbs up" button below.

    If there is anything else I can help you, let me know. Thank you.

  • Color LaserJet Pro 200 M251nw: color HP Laserjet Pro 200 M251nw prints no fonts more than 48 using Office WORD 2013

    If create a new Word document and I type the letters police 72, the letters do not print. If the font size is reduced to 48 it then prints. The new printer is connected to my laptop via USB. I use a HP laptop Pro 7420 s, 32-bit with MS Office H & B 2013. Any ideas as to what I need to check? Thank you.

    Thank you very much, Provost. Please send me the links, which makes it very easy for me. Upgrade to the latest firmware fixed the problem immediately. Accepted solution.

  • Color LaserJet Pro 200 M251nw: torn paper jam

    Hello

    One of the printers of the company I am based in had a printer Jam recently, some people tried to remove the paper from the printer and ended up ripping it (as seen in the image above). I was wondering what should do us from here, I tried to get out the paper but I didn't chance, any advice is appreciated

    It seems that the paper is stuck in the fuser unit.  Only suggestion I can offer is to do a search on google for the service manual and look for instructions to remove fusion and unit once you have the fuser unit you should be able to find a way to remove paper stuck in it.  Removal of the fuser unit is not as simple as that.

  • Windows 8.1 Surface RT and LaserJet Pro 200 (M251nw)

    Hello

    I just got today the printer (Color LaserJet Pro 200, M251nw).  I can't find the driver for Windows 8.1 RT.  Can you point me to a place I can download the driver from the RT?  The compatibility of Microsoft site says it's compatible...

    Thank you!

    Stacey

    @Stacey_CA

    The RT surface of windows is a basic tablet arm and use the drivers included in your operating system (in-os drivers). Please use the document below to help you to install the driver that is included in your operating system. You don't need to download anything.

    I install the driver included in windows 8.1

  • LaserJet Pro 200 m251nw: Laser Jet Pro 200 color ink bleed on black and white page after some use

    I print mostly black and white documents. I recently had 2 ink color of defamation in the pages that are supposed to be just in black and white printed. The first was the magenta, and it might discolor the entire page. The second was yellow, and it could fade just the left and right margins. It was two cartridges to Cartridge World, and they have done very well for some time after the installation or always had plenty of ink left when this problem occurred. The manager at Cartridge World has estimated that perhaps the part of the waste of the cartridge has been complete over time and flees to the ink. He said that for most black and white print still causes the drum on the cartridges of color to turn and empty the little ink in waste room. His suggestion was to get a second monochrome printer for most usage of my impression and just this HP product when the color is required. Who is? Other suggestions? If I replace the suspicious cartridges, print returns to normal, at least for a while.

    Hi @la1959,

    Welcome to the HP Forums!

    I see that your HP LaserJet Pro 200 M251nw, color of ink smear on black and white page after some use. I'm happy to help with this problem!

    According to the website of Cartridge World, http://www.cartridgeworld.com, it seems to me that these cartridges are rebuilt (refills). And, the information in this guide, can I refill the ink in my HP ink cartridge? States:

    Yes, you can. But what do you want? QualityLogic, one of the organizations of quality foremost in the world, has tested the performance of HP refurbished vs brand inkjet print cartridges (filled). Results: original HP inkjet cartridges ink far surpassed refills in print quality and reliability of printing.

  • M251nw color LaserJet pro 200: does print in black only, no color

    All of a sudden, my m251nw color laserjet pro 200 prints only black. Cartridges changed (C/M/Y) without modification. Toolbox shows that they are all 100%, but nothing will be printed in color, not even the Demo Page. Anyone able to help?

    Updated the firmware from hp, and it fixed the problem.

  • LaserJet Pro 200 m251nw: how to disable these pages printing pesky notification?

    I just bought the LaserJet Pro 200 m251nw to help with homeschooling and coupon printing. A big HUGE machine so far, one small complaint... whenever I have do something or something (ie: plan a printout of the spreadsheet on an app) Springs this page full color printing. I don't want to lose my ink telling me I just do what I know already! Can I disable it somehow? Thanks in advance!

    Hi @g33kyg1rl

    Welcome to the Forums of HP's Support.  I see you want to learn how to turn off notifications in HP connected for your Laserjet M251nw printer.

    Please follow the steps listed below:

    1. Connect to your HP account connected, which will take you to the Welcome screen.

    2. Please click the drop down arrow next to 'Settings' menu and choose 'Notifications '.

    3. If please check or clear the parameters of notifications that you prefer and then click on "save changes".

    Please let me know how it turns out.

  • HP Laserjet Pro 200 m251nw: I've got streaks printing on laserjet 200.

    All of a sudden, I have red streaks, printing on the right side of my documents. I tried using the cleaning page and it doesn't seem to help. I also have small black dots in various parts of the document which keep appearing on my documents. Cleaning that does not either.

    It seems to be a residue of red on the sponge roll just before the paper out of the printer. How can we clean this roller or must it be replaced to correct? I used my vacuumn to try to clean it up, but it doesn't do any good.

    Need help.

    Hey @AlaskaMariner,

    Welcome to the Forums of HP Support!

    I understand that you have a problem of magenta print quality printing of your color HP LaserJet Pro 200 M251nw of the printer. I would like to help you to solve this problem today. Thanks for the troubleshooting steps you have already tried before reaching out for support, including.

    On this model of printer there no zones in the product that you can clean it manually. The only method supported this printer paper path cleaning and area of the cartridge is running the cleaning page. You may need to run the cleaning a few times page to fix this.

    Sometimes red streaks can be caused by a low toner cartridge. When toner is low, it can gather in some areas inside the cartridge and create a "streak". I can have you hold the cartridge by the sides and shake it gently from left to right to redistribute the toner. Once the cartridge has been shaken, reinstall the cartridge. Once your cartridge is re-installed, please test print to see if the problem of dragging is still happening.

    If the problem persists you can please click here for the steps of quality supported by your printer. "Once the document of support opens please run through the steps to"check toner cartridge status"", "make the diagnosis of additional print quality" and "inspect the drum unit for damage".

    If the quality issue persists you may need to try a new HP authentic to verify whether this problem is caused by a magenta cartridge faulty cartridge or the printer.

    The black dots that you see are often caused by a dirty paper path roller or fuser on your printer number. As mentioned previously, the only way to solve a dirty paper path would be to run several pages of cleaning. A defective fuser unit would lead to a replacement of the entire unit.

    Please reply to this message with the result of your troubleshooting. Good luck!

  • Color LaserJet Pro 200 M27nw MFP - problem scanning ADF

    Seems to me a new Color LaserJet Pro 200 M27nw MFP running on a PC with Windows 8 and have come to realize that whenever I scan from the ADF Document (CAD), no output file is generated. The original document is drawn in by the document successfully feeder and the printer display indicates that the scan is ready. However, no analysis file is generated. This happens regardless of know if I send the output to USB or to e-mail and if the original document leaves simple or multiple.

    Interestingly, the ADF works fine if I try to produce paper copies, in other words, the printer is able to pull in the leaves o FRENCH original of the document in the ADF (as this either alone or several sheets) and to produce copies of the original successfully. Furthermore, I have no problem to scan multiple or single sheet documents when the original document is loaded by the Scanner flat, rather than the document feeder Scanner.

    Appreciate any help. Thank you

    Stephen

    HI @StephenScerri ,

    I see by your post that when scanning from the ADF there is no output file containing the scan which is generated on USB or e-mail. You can copy the ADF and scan successfully of the bucket. I would like to help.

    Is this printer the Pro 200 M127nw MFP Laserjet

    I have provided a document for how Scan: Windows 8

    When you scan from the magazine, you get an overview of the analysis of the computer software?

    What is the scan preview, but do not save it to the computer?

    What software are you using to scan?

    Try saving the scan on the computer, if you get a preview, to see if it will save the scan it.

    Please provide detailed results if you're still having problems.

    Have a great day!
    Thank you.

  • Print on the two option (duplex) sides missing Mac 10.8 for LaserJet Pro 200 M251nw

    I just purchased and installed a printer LaserJet Pro 200 color M251nw.

    From a Windows 7 machine, the properties of the printer box allows an option (I think on the finishing tab) for printing duplex (manual), which when used will then display a screen printing by telling you how to remove paper from the output tray and reload at the entrance, then press ok to continue with the other side of each print sheet.  I tried my laptop and it works fine.

    Even if it is a manual process for this printer, I would really like to be able to do when printing from my Mac, but it doesn't seem to be a way to select duplex printing.  Is it possible to have this feature?  Is there something I need to set differently on the printer?  It would be really useful.  Thank you.

    Hello
    The two-Sided feature reffer automatic two sided printing.
    As the specific device provide printing manual duplex only, you can perform duplexing manual as follows:

    In order to perform manual duplexing, Joanie you use the Pages to the printer setting, you will find listed in the manual duplex printing sectiong below:
    http://support.HP.com/us-en/document/c01663233

    Kind regards
    Shlomi

  • Color LaserJet Pro 200 M251n: LJ Pro200 M251n not print not some font sizes

    My new printer does not print text to certain sizes of fonts using Word or Publisher 2010. Until 60pt, it's good, but not 72, 100, or 120. However, it will print 240 pt. It will also display these text elements of the pdf document.

    Is this a driver problem? I use PCL6 but cannot find any drivers on the HP site. Do I need UPD PCL 6?

    Hello

    Update the latest firmware for the printer, which should solve this.

    Use the next tool if it is connected with a USB key:

    http://ftp.HP.com/pub/softlib/software13/COL44532/LJ-108129-8/M251_color_Series_FW_Update-20150212.exe

    For a network connection, follow these steps:

    http://support.HP.com/us-en/product/HP-LaserJet-Pro-200-color-printer-M251nw/5097632/model/5097639/document/c03341482

    Kind regards

    Shlomi

  • Color LaserJet Pro 200 M251 nw: unable to do manual duplex printing with Windows 10

    Using my prior desktop computer that ran from Windows 7, I had no difficulty to do manual duplex printing on my HP LaserJet Pro 200 M251 nw color.  However, having recently bought a new desktop computer running Windows 10, I have more two-sided printing option.  Instructions to Guide the user to http://h10032.www1.hp.com/ctg/Manual/c02886939 are unnecessary because I cannot complete step 3, click Finish.  After completing the first two steps by clicking on file - print and then click Properties or preferences, I am not provided with an option to "print on both sides (manually)" as described in the User Guide.  How can I get manual double-sided printing capability on Windows 10?

    Usually when you have a driver problem, it is best to find the current driver on the HP website, disconnect the printer from your PC, remove the existing driver, and then install the current driver.

    Windows often installs drivers that do not support as many features as the downloadable driver.

    If my post is solved your problem and click the accepted as button solution under him.

    In order to thank a Tech for a post click the thumbs up button under the post.

    You can even click on the two keys...

  • Color LaserJet pro 200 M276nw MFP - Scan configuration and installation on Mac Yosemite

    Hi all

    I just bought a new LaserJet pro 200 color MFP M276nw and I am trying (for 4 days) to coorectly install it.

    My goal would be to use it via the wifi connection and I put it correctly by the façade.

    When I try to install the printer on wifi, I can install the printer driver, but I can't find the driver for scanning.

    I tried to connect by ethernet and the system to emphasize a multifunction scanner and the printer driver. If use them, it works correctly.

    Whenever I go out the lan cable for use in wifi it lose the scan functions.

    What I am doing wrong?

    Thank you

    Gianluigi

    Hi @gianluigi1982 ,

    I see that you have problems with scanning via the wireless network, but you can scan through an Ethernet connection.

    I would like to help.

    Do you have what drivers installed the printer? (Apple update or the 10.9 download drivers)

    I checked our laboratory with 10.10 installed on this computer and I was able to browse for printers and Scanners on the wireless network.

    Check the version of the driver installed.

    Go to the Apple preferences system, printers, and Scanners, highlight the Laserjet printers, click the print tab on the right side of the window, and select the Options and supplies.
    Under the general tab it will give the list the version of the driver.
    19.9 is one on the lab.

    Which driver you have show?

    Check the name of the driver that is installed by the printer. Make sure that it shows just the name of the printer.
    Click on the Apple menu, click System Preferences. Click on Printers & Scanners, highlight the name of the printer on the left side and right side of the screen it should show the name of the printer. (MFP Laserjet Pro 200 M276)

    If the full name of the printer is not correctly, delete and add the printer name back from the list. Click on the sign - to remove the driver and then click on the + sign to add the driver might have to drop-down list to select the name of the printer to add a click.

    In the printers and Scanners window, highlight the printer on the left side, to the right of the window, you should have a print/scan tab, click Scan, and then open Scanners and test scanning. If you do not have the scan tab, let me know.

    Have you added the printer as your Hello or via the IP protocol? (cannot scan through the IP Protocol)

    You use the automatic IP address or your own static IP address?

    Here is some information for scanning in OS X v10.10 Yosemite without software HP.

    Please provide detailed results if you're still having problems.

    Good day!
    Thank you.

Maybe you are looking for

  • nc6000 SD slot

    Is could someone PLEASE tell me why on the nc6000 the slit on the side will read/wright to use a 2 GB SD card and not a 8 GB card? Using a USB card reader I can read/wright on the card 8 GB SD is a good card. Thanks for any help! onhoj

  • Pavilion a1330n: where can I get the update for XP SP3

    Microsoft becomes the avilable SP3 upgrade. My hard drive of the system has failed and the backup has only SP2. Is there a safe place to download SP3

  • Can I move photos to computer iMac iPhone 6?

    I want to import all the photos in my iPhone 6 (iOS 9.1) on my Mac, delete all phone, remove a lot of the computer, then put back the survivors on the iPhone to show to friends on the fly. Possible?

  • Channel number (GroupIndexGet provided works that you know the name of Group) group

    As it says in the title. Im trying to get the index number of the user's group after selecting a channel. The ChannelNameGet relies also on that you know the index of the group here, any help would be greatly appreciated! Thank you very much Dan

  • Problem with the file dialog box

    Hello erveryone,. My problem is quite easy... I try to use the file of dialogue vi of NOR and its work properly, but when I select a file using the double click, the second click is detected as a click on my Panel of... Example, if the file I select