command + space on iOS 10

On my mac keyboard shortcut "Command-space" has always been to change the language of the keyboard. The same key combination activates / deactivates the language on my ipad and keyboard to connect the keyboard. But from the iOS firmware 9 instead of the tongue appears spotlight. I wrote and called to support. I was hoping that fix you this in new firmware. But you do not. Now, it is very comfortable and little used to change keyboard language!

Sorry for my bad English.

It has been changed to control more space with iOS 9.  You just use it instead.  Nobody is going to restore it.

Tags: iPad

Similar Questions

  • lack of shortcuts - hand (SPACEBAR) and zoom (command + space) - El capitan

    Just updated to El capitan and noticed some indesign shortcuts are no longer works.

    hand (SPACEBAR)

    Zoom (command + space)

    Option + do drag does not create a copy either, although the cursor changes to double slider

    Go to System Preferences > keyboard > keyboard shortcuts. Change your shortcut for Spotlight (use the command + space by default, you can change it).

    If it's not her, some third party software (often a browser extension) is striking strikes. Quit all applications, restart. Open InDesign before first load something else and try again.

  • Feast your eyes on the hassles of storage space on IOS

    So I have a very large collection of photographs, a couple hundred concerts a value and I thought that Adobe Revel would be the way to go to clean up quickly and easily with access on all my devices.

    The problems is that the Adobe Revel app for my iPhone 4 (as well as all applications IOS Revel) insists on storing thumbnails of ALL my photos from my collection of 16,000 + photo. This means that more than 500 megabytes of space on my phone value is constantly dedicated to store photos that I rarely need. This may not seem a big deal to some, on a device with 14 GB of free space value, 500 MB is the equivalent of half of a film or a few pounds of medium length.

    I appreciate the convenience of being able to scroll through everything quickly because it is already loaded. I understand that. But it's the 21st century and I think that we should have a few choices as to the amount of space this app takes over. I mean, my collection of photos is not exactly going to become all small is it?

    I think we should be able to establish within Revel HOW MUCH storage the application will use to these thumbnails instead of having the decision EVERY being by default. In view of my own choice, I would set it at everything marked as a favorite and everything from the last 2 weeks. I think it's a thing just to ask for a big developer that Adobe can easily use it in their product.

    Because right now the app is completely broken. Any attempt to open the application causes the message pop up "not enough local storage space: import was stopped because there is not enough storage available to Revel on this device." Please free up some space and try again. "Rejecting this message only allows him to appear again IMMEDIATELY. Can we at least fix the application so that I can still import to the cloud from my phone even when my phone cannot accept any thumbnails more?

    Has anyone else encountered this problem?

    If you are using a MAC, then you can check the State of the (s) library view and make sure that nothing is in the download queue. You can do so by looking at each library, click on the point to the left of the name. It will give you a status for this library. If you are sure that all additions are made, clear the caches for each library. You can have more than one library using the space.

    On your iphone or ipad, switch to the view of the library for each library and look at the left icon of low clouds over the library icon. Beside that, you will see "updated" if she has completed synchronization.  You can click on the cloud for more information.

    You can also confirm the images are uploaded by signing into the same account using another device or a browser to www.adoberevel.com. Try to download some original images. If more loads are completed, you should see the new images download and be able to view them.

    If the files are synchronized and empty the cache doesn't help, I suggest that you remove the application, and then reload. Your photos will always be safe stored in the cloud. You will have some time to delay the first use you it because of the loading in the thumbnails. Please let me know if this reduces the amount of space used.

    Guinot

  • Space insufficient ios

    I have an iphone 6 currently running on ios9.3 and my phone has 16 GB which I receive something around 14-15, 5 GB free space. But my iphone was worth 12 apps n only 3 applications takes not more than 300 mb while rest are under 100 MB + 20 images with no video and also my deleated currently is empty but my phone shows that I have 200-800 MB apart about 15 GB! It never rises even if I barely consumed 1 GB of storage! Why is it so n how to find solution to this problem?

    You have WhatsApp? If so delete, do a forced restart and check. If you do not, you may need to restore your iPhone as an application or the system could be damaged.

    https://support.Apple.com/en-us/HT201252

  • Problem upgraiding new iOs Version

    Greetings!

    Please help me, im having a problem with the download to update my iOS version larest do I need to have enough memory for this? My current memory space is 797 MB. How much it would be for the memory so I can finally upgrade to the latest version.

    Here I have attatched a screen shot based on the results of the failure of the aftert to install the new version of the iOSthank you.

    You try to live update?  Try to install by connecting to a computer using iTunes. Who will save storage during the upgrade.

    This link explains how update via iTunes: update the iOS on your iPhone, iPad or iPod touch - Apple Support software

    Upgrade to iOS 10 requires a lot of free space:

    https://www.imyfone.com/iPhone-space-saver/iOS-storage-management/

  • Send the command to laser sensor via a serial port RS232

    Hello

    I have a sensor of moving Laser of OPTEX FA Co., LTD. with a Communication Manual.pdf file attached. I modified the sample base series write and Read.vi of LV to send the command to the probe in order to receive a response. However, LV always returns an error on my VISA Write.

    In short, the structure of command for the sensor must have a form like this

    STX-command command-space-1 2 - ETX

    (more can be see the manual on page 3 or 18 of the .pdf file)

    where

    -STX: code showing the head of transmit data (02 H)

    -Command 1, 2: could be refers to table 1, 2 and 3 of the manual.

    -ETX: code illustrating the completion of data transmission (03H)

    For example, if I want to ask the sensor to send the data from A sensor head, the command must be

    STX-ABLE () A - ETX

    (20H) space is shown as ().

    I tried to send a string HEX (02 - 4 d 454153555245-20-41-03) for this command to the entry VISA, but all I get is ERROR.

    I enclose with this thread my vi and a printscreen of the ERROR.

    A lot a lot of appreciation for any help from any of you.

    I have my LV code can run successfully. He can read the COMMAND and return measurement data. The last time does not playback VISA because I used a cable RS232 to opportunity, and someone operated two pins (2 and 3) for another application.

  • Zoom in Photoshop (Alt/Option + space + mouse click)

    Hello community,

    could please tell me that this is possible and how it is to bind the zoom rear ALT/Option + space + mouse click?

    This Photoshop-like behavior is already existing for zoom in: command + space + mouse click.

    Thanks a lot and what is nature!

    Obi - wan Kenobi says:

    Zoom - Alt-Cmd-space-Click =

    To the right and to the original question: while keyboard shortcuts can be customized, determine + click combinations cannot.

  • Shrink a table and space recovery

    Windows 2008 Server - Oracle 11g 11.0.2

    I had a problem with a table with more than 30 million lines.
    I discovered that a routine created unnecessary lines inside this table.
    The owner of the application sets the routine and I deleted more than 23 million rows in the table.

    To reclaim the space in the table, I activated the option of moving line.
    And then I used the command space shrink.

    I checked in EM and I saw that the table using 10.3 Gbs, now it is using only 2.2 GB.

    In EM, this new free space, more than 8 GB, acknowledged in tablespace and datafile.
    Segment Advisor did not recognize the new free space yet, so the recommendation to reduce is stil there.
    And I want to resize the data file.

    I used EM to resize the data from 12 GB to 5 GB file.
    I see in MS that only 2.5 Gbs are used in this data file.
    But I got the error ORA-03297, file contains data used beyond the requested value of resizing.

    What can I do in order to resize the data file?

    Thanks in advance,
    Ed

    There is a map of tablespace option in MS where you can hover over the segments towards the end of the data file to find out what they are, then you can use one of the many methods to move them from the road.

    Administration--> tablespaces--> click on tablespace--> menu actions drop-down menu to display the contents of the Tablespace--> expand scope map

    May take a while to process.

    See http://www.oracle-base.com/articles/misc/ReclaimingUnusedSpace.php

  • How do Com + Space = zoom Drag space

    I forgot.

    How do the command + space + drag to enlarge the drag area?

    Not scubby zoom (even if I forgot how to turn that off, I already put the SZ OFF) - I would JUST drag the box I want to zoom out...

    12.0.4

    To disable, select the Zoom tool and uncheck the 'Zoom brush' on the toolbar options: http://phtshp.us/CS5Zoom

  • Questions about IDS 4.0 and 4.0 VEI

    I played with IDS/IDM/VEI 4.0 and so far, I am really impressed with the upgrade!

    A few questions/suggestions:

    (1) with IDM, to detect the signature configuration, is there a quick way to edit a particular number of signature? For example I mean tune signature 3041 - the only way I can find to do if I don't know the category is to collect all the signatures, then try to guess which page it's. I think that the previous version had a pop-up that listed the range of signatures on each page.

    (2) a Suggestion: in VEI, looking at a view, the first column is a group, and the second column contains the number of elements contained in this group. However, a double click on the first column does not give detail, only double clicking on column 2. It would be nice if the first column is also. (For example, for the severity level group, it would be nice to double-click on the word 'High' to see all the signatures of high status.)

    (3) is there a simple way to VEI or IDM to see connections have been blocked? It would be nice to have a summary paper when connections have been blocked and which IP addresses have been affected. It would also be groovy if it was shown in the VEI in the individual events (IE. Add a column 'Action' showing what decisions have been taken, as appropriate for each shot of signature)

    (4) is it possible to export the settings I changed default value? So far I've just kept a Notepad file that lists the signatures I've set in case I have to re - install. (And from the looks of it, upgrade to the latest signatures wiped out my block settings)

    (5) what is the difference between ShunHost & ShunConnection? The documentation does not really. And it is designed to work with IOS vs Pix fleeing?

    (6) the Docs for IDM imply that system variables can be used in the event filters, but when I try to apply the system IN variable for a filter, it won't let me so I have to type in logical addresses.

    That's all for now!

    I am pleased to hear that you like the new versions. My answers to some of these questions/comments I hope to improve your experience.

    (1) with IDM, to detect the signature configuration, is there a quick way to edit a particular number of signature? For example I mean tune signature 3041 - the only way I can find to do if I don't know the category is to collect all the signatures, then try to guess which page it's. I think that the previous version had a pop-up that listed the range of signatures on each page.

    ANSWER: not at the moment. We have heard this feature of multiple users request. A future version 4.0 is already planned to bring back the feature 3.1 (announcement of the signature by page range). Cannot comment on when this version will be released.

    An alternative until then would be to select the option to view all transmissions on the page (it will take a while to load), then use the search button in your browser to take you to the line for the signature.

    (2) a Suggestion: in VEI, looking at a view, the first column is a group, and the second column contains the number of elements contained in this group. However, a double click on the first column does not give detail, only double clicking on column 2. It would be nice if the first column is also. (For example, for the severity level group, it would be nice to double-click on the word 'High' to see all the signatures of high status.)

    ANSWER: I'll pass it on the developers.

    (3) is there a simple way to VEI or IDM to see connections have been blocked? It would be nice to have a summary paper when connections have been blocked and which IP addresses have been affected. It would also be groovy if it was shown in the VEI in the individual events (IE. Add a column 'Action' showing what decisions have been taken, as appropriate for each shot of signature)

    ANSWER: IDM manual locking tab will provide you with the current block list as allow you to add blocks or remove existing blocks.

    It's called 'Manual blocking' but it will also show you the current 'automatic blocking' (you may switch to another screen IDM, and then return to be refreshed with the latest red list)

    http://www.Cisco.com/univercd/CC/TD/doc/product/iaabu/csids/csids9/idmiev/swchap5.htm#195940

    Also, you can run the line "view events" to show you what the blocks have been tried. If I remember correctly, the events to see the line you would be: "view the events of the NAC" where the time and date is the entrance earlier you want to display. (NOTE: NAC = Network Access Controller - replacement for managed in the new sensor V4.0).

    I recommend playing with the different possibilities to show events to see the different information that the sensor can bring in the new CLI.

    In addition, the attempted action is now included in the alarm itself and IEV should have a column IPLOG, SHUN and TCP Reset show what action was attempted. You check the settings, and then make sure that you have these selected columns is displayed in your view. (The actions attempts are visible when looking at individual alarms and not all summary windows)

    (4) is it possible to export the settings I changed default value? So far I've just kept a Notepad file that lists the signatures I've set in case I have to re - install. (And from the looks of it, upgrade to the latest signatures wiped out my block settings)

    CLI the commmands to check:

    more current-config - gives a style CLI listing the configuraiton, under the area of virtualSensor, it shows you just changes to the signatures rather than see the definition of default full signature.

    Copy current-config config backup - backups your current config in a storage space on the sensor itself

    Copy current-config - allows you to save your configuration to the location. The location could be an ftp server, or scp.

    Example:

    copy @10.1.1.1/config-backups/sensor1-config ftp://usercurrent config

    (5) what is the difference between ShunHost & ShunConnection? The documentation does not really. And it is designed to work with IOS vs Pix fleeing?

    Shun host creates the following ACL entry:

    refuse any ip

    SO it blocks all packets from the source.

    Shun connection on the otherhand creates the following ACL entry

    (NOTE: I am doing this out of memory so I'm not entirely because of my response below, you may need to test to know for sure):

    refuse eq

    SO it blocks only the packets from the source to the ip of the victim who go to the same port where the attack occurred.

    NOTE: Multiple connections to the same srcip Shun may cause the glines being combined into a single host Shun to prevent that IP to fill your ACL list.

    Regarding IOS vs PIX. The above commands are for IOS. Similar entries can be seen with the command "run away" from the Pix, but no matter what you enter with the command "run away" from the Pix, he will always shun the entire source ip address. So if you Shun connections with a Pix command "escape" has other information, but the Pix will always shun the sourceip together.

    (6) the Docs for IDM imply that system variables can be used in the event filters, but when I try to apply the system IN variable for a filter, it won't let me so I have to type in logical addresses.

    Looks like maybe it's a bug.

  • Siri is disabled but the pop-up keeps asking if I want to activate.

    After update to Sierra I activated the Siri, but it kept open without prompting, which has been a nuisance. For the next, I disabled Siri in system preferences. Now, a pop up keeps asking if I want to activate Siri. Happen every minute or two and sometimes every few seconds.  How can I stop this?

    FWIW, I had installed since the first Sierra developer beta and it is never once opened without asking for confirmation. If accidentally you press command + space bar which will open Siri. I have no idea why, if disabled it keeps asking if you want to activate it unless you are pressing and by now the command + SPACEBAR.

  • Change keyboard shortcuts presets in El Capitan

    I use El Capitan.

    Before the update to the new version, I am generally familiar with "command-space bar.

    to switch between two input languages.

    But after upgrade, it became "Ctrl + space".

    I tried to change the predefined hotkey but by using 'Ctrl + F7' by following the instructions

    the preference of the system does not allow me to change anything, even my priority account is administrator.

    Is there anyone know how to fix this?

    Thank you

    Control + F7 is already assigned to a shortcut ' ' so you should have to change two or disable the ' hotkey '.

  • Why stock PIN request when you use Apple pay?

    I use iPhone 6 with 64 GB, with 27.8 MB of available space, with iOS 9.3.2

    I was happy until today to be able to use Apple pay Walgreen pharmacies.

    Today Apple pay (or something) forced me to enter my pin code of the debit card, I've always used.

    What has caused this?  It does not match my original understanding of the purpose of Apple pay ("just touch and go.")

    I read article Apple support that it CAN happen, but it has never before.

    Walgreen has changed something on Apple payroll process?  Walgreen, which would explain?

    My Bank has changed something?  That would explain my Bank?

    Apple changed something?  Apple which would explain?

    How does the consumer learn this info?   I don't have the time to study with three different companies, nor devrais I must.

    Am I unreasonable?  Could someone explain to me how?

    Hello

    When making a payment in a shop in the United States with your debit via Apple card pay, you may be prompted to choose credit or debit on the terminal.

    If so, Apple recommends you always choose credit (even if the chosen card is a debit card).

    Choose the debit may not always work successfully with a few old merchant payment terminals and back-end systems.

  • login problem admin

    Hello

    I hope that there is someone who can help me.

    When I connect the iMac (el capitan 10.11.3), bought in February. 2016, with the admin account, there no problem.

    When I go to the user & preferences of groups to make some changes to the same admin account, I try to unlock the admin account. I fill the same password but it keep nine of the 10 times saying the password is not correct. I tried to change my password but he repeats to me that the password is incorrect. I do not use my ID apple for this admin account password. I would like to open a session without trying 25 times or more...

    Thank you for your attention,

    Kind regards

    Toos

    First, please ensure that caps lock is not on. Note that on some models of laptops, the LED of the caps lock key may not work when you start up if FileVault is turned on. When shift caps lock is enabled, there will be an arrow icon in the text box where you enter the password. Build on this, not on the LED.

    Another reason why the password can not be recognized, is that the keyboard (input source) in the login screen is not what you expect. You can select one of the available provisions by choosing in the menu flag in the upper right, if it is displayed, or even browse the by pressing the key combination command-space or command-option-space.

    If the user account is associated with an Apple ID, and you know the password Apple ID, then maybeApple ID can be used to reset your password for the user account. In OS X 10.10 and later versions, this option also works with FileVault, but only if you have enabled when you turn on FileVault. It is not retroactive. If not, see below.

    Note: If you have enabled FileVault, this procedure does not apply. Follow rather the instructions on this page, under the heading "If you forget your password."

    Start in recovery mode. When OS X Utilities window, select

    Utilities ▹ Terminal

    in the menu bar at the top of the screen, not one of the items in the OS X Utilities window.

    In the window that opens, type this:

    resetp

    Press the tab key. The partial order you entered will automatically end this:

    resetpassword

    Press return. Opens a window to reset the password. Close the Terminal window to get him out of the way.

    Select the boot volume ("Macintosh HD", unless you have given it a different name) if not already selected. You won't be able to do this if FileVault is turned on.

    Select your username in the menu option allows you to select the account if not already selected.

    Follow the prompts to reset the password. It is safer to choose a password that includes only the characters a - z, A - Z and 0-9.

    Select

    ▹ Restart 

    in the menu bar.

    You should now be able to login with the new password, but will reset the keychain (empty). If you have forgotten the password for the keychain (which is normally the same as the password for the connection), there is no way to recover it.

  • I buy refurbished macbook pro without knowing?

    Hello

    I bought a new macbook pro 13 "2015 with the apple retina display"premium reseller"in Singapore, I stayed here for 2 days only for business trip.

    After to return home (Israel), due to the relatively quiet environment, I noticed noises weird fan (sounds enough) low-end (around 1300 ~ 1400), the noise sounds like there is something touching the blade fans and often happens when Im holding the macbook in different angels.

    A week later I noticed "click on" sounds when the tilt of the laptop, after some research (by browsing the web), I found that there is a plate inside the screen that turns freely after the display heating somewhat.

    My default source entry shortcut is (Ctrl + space), but when I compared the shortcut MacBook with my colleagues, I found that their shortcut (cmd + space). I do not remember to set\change the shortcut since the purchase of the macbook, and nobody messed with it once I got it of course. When U tried to restore the default shortcut for the preference, he remained the same as it is by default, however, as far as I know the supposed default shortcut be cmd + space.

    My battery life is low compared to my colleagues MacBooks (the same models, and one of them even got high 2.9 GHZ model). I don't use chrome and I have no other applications running in the background. IM checking the activity monitor often and I'm not saying any application that drains my battery though the time I usually get my battery gives me 4 hours to 75%. The battery status shows normal. I charge my battery by following the instructions and parameters are defined to save the battery (bluetooth off, half the brightness value, bright keyboard is off etc.)

    I went to the apple in Israel dealer to repair the fan noise and now I'm waiting for them to give me a computer for which mine will be under contract (up to 10 business days).

    I would like to know what you think of my case.

    Thank you

    Natanborochov wrote:

    ...

    My default source entry shortcut is (Ctrl + space), but when I compared the shortcut MacBook with my colleagues, I found that their shortcut (cmd + space). ...

    Your command-space shortcut is good by default. Their setting is not the default.

Maybe you are looking for