Compaq 061 sees no audio after BIOS update

Similar Questions

• Unknown device on the Satellite A100-153, after BIOS update to 5.1

  ACPI\TOS1901 * TOS1901<--- this="" is="" the="" unknown="" device="" after="" bios="" update="" to="" 5.10="" on="" my="" satellite="" a100-153="">

  Vista now shows it in as unknown device manager; the TOS1900 showed up too, but after installation of Toshiba Value Pack for Vista, it went.

  Help, please. WHICH IS: ACPI\TOS1901 * TOS1901

  Hello

  ACPI-> Advanced Configuration and Power Interface
  ACPI defines hardware and software interfaces that allow focus on the OS configuration and power management to enumerate and configure motherboard devices.
  For example: ACPI is necessary for the standby and hibernation mode.

  Now your question; the new BIOS has been updated and configured to using VISTA.
  It seems that VISTA was not compatible with the previous version of BIOS because the ACPI interface. Now you can install Vista on the laptop, but it seems that you need a driver. Possibly new chipset driver version might help. But as you probably know, the drivers are not available at this time. Unfortunately

• Satellite L450D - 13 X - blue screen after BIOS update

  I have the blue screen after BIOS update. Satellite L450D - 13 X worked ok before that ideas?

  Is there contact information for Support TOSHIBA?

  Hey,.

  > Is there any TOSHIBA support contact information?
  No, becaue, must contact an authorized service provider. Guys can help on any hardware and software problems and can also order spare parts from Toshiba.

  Here is a list of aspic, where you can look closer:
  http://EU.computers.Toshiba-Europe.com/innovation/generic/ASP_SUPPORT

  Good luck! :)
  ?

• Satellite M100 - no speakers sound thorugh after BIOS update

  Hi all

  I have satelite M100 PSMAAA-02006 with XP. I just updated the Bios on V3.0. Speakers do not work after update but the audio jack works so with headphones I can listen to but not through Laptop speakers and the keys to media on top of keyboard play, pause, stop, next, back, etc. homepage react too much.

  Someone knows the solution to this issue. Or is it possible to get the old BIOS? Although I not sure aboutt previous version.

  need quick help. Please answer as soon as possible.

  Thanks & best regards...

  Hi Julie,.

  I doubt that this was due the update of the BIOS. Is that what you have loaded default settings after updating the BIOS?
  Have you chosen the correct BIOS update?

  Normally you can hear the sound on the speakers laptop if you disconnect the headset. Make sure that the sound is not muted, you can do this with the FN + ESC key combination.

  About the multimedia keys, I would recommend reinstallation of Toshiba common Modules. You can find it on the Toshiba site.

• Compaq dc7800: DC7800 CPu id and BIOS update probem

  Hello

  My first post here, I hope you get what I'm trying to say.

  Well, I have this old compaq dc7800 sff and I managed to level it's OS to Windows 10.

  And now, I would like to update its bios and CPU id, but I can't run those exe, I downloaded on the cd7800 support site.

  I know that these bios update programs and so forth are not published for Windows 10, but I thought that windows7 versions would work.

  But they did not.

  For some reason, I got the the messege that "software publisher has refused to run this program on this computer.

  While this mean?

  I can't run these programs even with administrator privileges, I get the same messages?

  Because of Windows 10? Or what?

  The reason why I came across this problem was that I tried to update the CPU of the Q6600 to Q9550 and I got the error of CPU - ID firmware.

  Hello:

  It is very easy to update the BIOS on a dc7800 without being under Windows.

  In the menu of the BIOS on the file tab, there is a rom flash system command.

  All you have to do is put the BIOS files on a USB stick formatted with the FAT32 file system.

  Rather than go though all the steps to get the BIOS files, I've zipped or less than joint under attachments.

  Unzip them and copy the content of the file of the folder (not the folder), for your USB flash drive.

  Plug the flash drive into your PC and restart it, tap the F10 key to access the bios, select the file menu and on this list will be a rom flash system command.

  What to choose, and the PC will 'see' the files on the flash drive.  Follow the instructions on the screen to Flash the BIOS.

  I have attached files to the latest revision of the BIOS (1.32 Rev. A (6 Dec 2011)).

  If you still get the microcode error after updated the BIOS with the latest version, let me know, because then update the firmware, and it is a much more complex process.

• No noise/driver does not work after BIOS update

  Hey, I'm having a problem with my audio drivers. I have what I think is a HP P5RC - motherboard (I'm still not positive, because it was given to me, and I not found any precise identification on it), and I use the onboard sound on this subject. I've had versions of Windows 7 on this computer since the Release Candidate, and at the time I had to manually download the Realtek audio drivers to get the sound to work. I had to do the same thing when I got the full version of 7 Ultimate. After installing Win7, I had various problems. I was able to trace the problem down to the motherboard, but wasn't sure if it was a hardware or BIOS problem. I tried updating the BIOS to Bishop 3.08 since this page and found no big difference, apart from the fact that the sound did not work. I tried redownloading and installing Realtek drivers and restarted, but I still get all the sounds. What is another problem with the material of the motherboard, BIOS update problem or a driver problem?

  Thanks in advance!

  -AMV_Ph34r

  Edit: I should probably note that I built the computer and used the motherboard that was given to me in this document is not an HP computer.

  Edit 2: Another note - I have an Asus EAH3450 video card, which has a HDMI port on it. HDMI audio driver has two audio devices in the control panel and Device Manager. However, I do not have a compatible monitor HDMI, so I need the built-in sound card.

  Because your video card can also function as a sound card you must go into the BIOS and change your sound option to 'Auto' (which is probably trying to use your card as the audio device video by default) for the on-board sound of motherboards.

  If you found my answer helpful please say thanks with a KUDO (click on the star).

• Satellite Pro P200-15W: after Bios Update 1.90 incredibly noisy fan

  Hi, I have a Toshiba Satellite Pro P200-15W, I recently made an update to BIOS version 1.9 and seems to have been a big mistake.
  After restarting the computer, I had a lot of software deconfig and the fan has become incredibly noisy.

  I have the problem with the Toshiba Vista registration software, I get this message: "registration of Vista has stopped working". I read other discussions, I don't want to just disable it in the start.ini file, I would actually solve the problem if there is a way.

  Is there a way to change the configuration of fans? I read a post from Toshiba on another model of laptop that has had the same problem of noisy fans after an update of the BIOS, they gave that a solution with a new version of the BIOS, is there a way to reverse the BIOS to the previous version? (recovery CD will be useful for this purpose)?

  See you soon

  Edgard

  Hello

  It seems that the picture of the fan was changed and renewed in the new version of BIOS, and so fans run fall.
  Why the table fan has been changed?

  Well, usually something like this is necessary to improve the reduction of the internal temperature while the CPU and GPU are running with maximum performance.
  This helps to prevent the equipment from damage!

  Usually, the recovery CD formats the whole HARD drive (partitions too) and installs only the image of Toshiba on the notebooks of HARD drive.
  The image contains the OS, drivers and additional software and has nothing to do with the BIOS update.
  But you can try to recover the laptop to see if you can solve the problems of software as "Vista record"!

  If you want to reverse the BIOS, you will need to contact the ASP in your country!

  Sorry, but all I can suggest.

  Best regards

• Portege M800 no boot after BIOS update

  Hello

  I encountered some problems with my netbook (Portege M800-10W) after the BIOS update.
  The update of the BIOS program appears failed. Then my Netbook automatically rebooted and now I can't start my PC more.
  All the LEDs will light up but the screen remains black and after a few minutes, the beep 3 times (1 long, 2 cm) netbook.

  How do I restore the BIOS to the previous version (or plant)?

  Thank you.

  Adrien

  null

  Hi Adrien

  I think that Akuma is right. Your laptop must be verified by the service of Toshiba s. Let check your laptop and I hope they will help you with this.

• Satellite L750 - Bluetooth does not work after BIOS update

  I am preparing some L750 notebooks for use and accept updates from the Toshiba, which included an upgrade of BIOS v1.70 for v2.00. He appears after this update occurs that Bluetooth no longer works, i.e. try to install Bluetooth Toshiba stack will fail as it is said that the Bluetooth radio is disabled and must be turned on for continue.

  As the L750 (model PSK1WA-0C300R) is not a hardware switch to enable or disable the Bluetooth/Wi-Fi, the only option available (Fn + F8) is unsuccessful. I ran a recovery of factory default installation and Bluetooth still does not - resumption of classes does not restore the BIOS to the previous version. I have 5 of the model and confirmed the update of the BIOS is the cause. Two laptops now have v2.00 and Bluetooth has been tested in the work before the update of the BIOS.

  If Bluetooth is not critical for the environment which I deploy these notebooks, it's an annoyance I want to solve. My questions are: has anyone encounter the same problem and managed to resolve it? Is there a BIOS v1.70 available for download to restore the functionality? Y at - it an update of the BIOS > V2.00 for solve the problem I have? Thank you.

  Hi JasonL750,

  Load default settings after updating the BIOS? Go into the BIOS, press the F9 key to load the default settings of the installation. Also, make sure that Bluetooth is enabled in the BIOS if there is such an option.

  In addition, it would be interesting to know what happens if you use the FN + F8 key combination. Don't you see that he has an option to turn on Bluetooth and if so what happens if you do this?

• Satellite C55-A-16Z - graphics card does not work after BIOS update

  Hello

  I have a portable Satellite C55-A-16Z with windows 8 and a Nvidia geforce 740M graphics card.

  Last week he asked me to update the version of the bios at 1.30.
  The bios update was successful.

  However when I restarted my laptop I started having a BSOD dgxkrnl.sys.
  Correction of the error and restarted for an another BSOD Windows, and after the second solution, I stopped making BSOD.
  But now, I noticed its games running, if not use the dedicated card, but use the 4000 Intel.

  In the settings Nvidia dedicated card is configured to be always on.
  It seems that my card is missing, but it appears in Device Manager.
  I tried to delete, update the drivers and the default factory reset, but nothing helped.

  Also, when I go into Options power the Intel card is listed and when I disable the card intel in the Device Manager it starts to use the graphic viewer for windows.

  How can I get my Nvidia card to work again?
  Any help is appreciated.

  Thanks in advance.

  Hello

  After the BIOS update the BIOS should be set to default settings.
  You can do it in the BIOS.

  In addition, you mentioned that Windows 8 is still installed on your laptop.
  8.1 to win has already been published by Microsoft and I highly recommend that update you the system of 8 to 8.1 Win Win.

  Before you start the upgrade to 8.1 win, you should check and read the instructions step by step for Toshiba: http://www.toshiba.eu/innovation/generic/windows8_1-message/

  I guess that after the Win 8.1, nVidia graphics card upgrade works well also.

  Your comments would be greatly appreciated.

• Satellite C650 - black screen after BIOS update

  My Satellite C650 Windows 7 - won't start afte BIOS update / switch.

  Everything worked very well until the automatic update of Toshiba asked me to download and install the new BIOS update, I did. At the same session Windows and McAfee asked updated. I agreed to all. After all updates have been installed, turns off. The next day when I walk, I see only black screen. I also tried F2, F12 and drive recovery. Nothing happens!

  Any recommendation?

  Hey,.

  It seems that something was wrong during the update of the BIOS and so that you can t the computer unbootable. But I put t understand why you did the BIOS update. If everything works correctly, you can forget about this update. More if you do a BIOS update you shouldn't t run any other updates or programs that might affect the update of the BIOS.

  Anyway, in this case you can do nothing and you need professional help. Please contact an authorized service provider and guys can help you update the ROM module On the Web from Toshiba site, you can find a list of all the FSA:
  http://EU.computers.Toshiba-Europe.com > support & downloads > find an authorized service provider

  Good luck! :)

• Satellite Pro A300 - touchpad failed after BIOS update

  After that good BIOS update 2.00 to 2.10 / suggest by ALERT TEMPRO - http://support1.toshiba-tro.de/tedd-files2/0/bios-20091125132031.zip/ the touchpad of my Satellite Pro A300 - GR 1 stopped working.
  He appears under the name hidden in Device Manager. The State of the device - "this device is not present, is not working properly or is not all its drivers installed." (Code 24) "reinstall the driver has no effect of course. I can also access the BIOS utility when you start pressing F2.
  Running Vista Business 32-bit Edition.
  Ideas to solve the problem will be highly appreciated!

  Hello

  Normally, it should be possible access the BIOS, if you press F2, once you have turned on the laptop. Please check again and load the default settings there.
  And you cannot access the BIOS if you shut down the computer.

  You can use an external mouse on the laptop? Please check this too.

  I've also updated the BIOS on my Satellite A300 but I n t have a problem with the touchpad after the update.

• Laptop HP OMEN - 15-5010nr: Omen HP 15: backlit keyboard does not not after BIOS update

  This morning my HP omen arrived by mail, fully functional with everything in tact. After I left my laptop to install the updates from HP Support Assistant (one of these being an update of the BIOS updates), I returned to find my computer restarted and my enlightened retro keyboard does not. After trying to use HP OMEN control to fix the keyboard, I found the keyboard flashes when I click "Apply to all Zones", but then immediately turns off again. Is it possible to fix this keyboard backlit ir question can we see an update in the near future that resolves this problem?

  Found a solution! Apparently, the keyboard stops after the update of the BIOS, so to reactivate just push F5.

• Re: Satellite - blue screen after BIOS update

  Hello

  My computer laptop girls worked very well until I did the BIOS update this morning. Now, I get the blue screen of death STOP: 0X0000007F. Help, please

  concerning

  Carol

  Hey, Carol, welcome to the forum! :)

  Don t misunderstand me, but may I ask why you n t post more information about your problem?
  Important to know is that your laptop you have exactly and where to download the updated BIOS and for what model. This is important information.

  By the way: have you ever tried to load the default settings in the BIOS after update?

• PAVILION NOTEBOOK 15 K7Q21EA #: SCROLLING WINDOWS PROBLEM AFTER BIOS UPDATED 10 (08/03/2016) PAVILION 15 YESTERDAY 16/10/2016

  CANNOT CONTROL THE SCROLLING. CURSOR DOWN TO THE LOW WHAT MAKES IMPOSSIBLE TO SAVE TO A FOLDER

  Hi @STICKMAN5124,

  Nice day! Thank you for your participation in the Forums of HP Support! It is a great location to get resolutions and interact with experts from the community. It will be a pleasure to help you.

  I saw the post and understand that after only a bios updated cursor drops down due to a problem of scrolling.

  Impressive work, do the update of the bios. Kudos to you for this. It is a privilege to work with tech-savvy and technically competent customers like you and we greatly appreciate your business with HP. You have been great to work with.

  Please check in F2 diagnostics if the scrollbar works correctly. If Yes, then you can update the chipset drivers and http://hp.com/drivers touchpad drivers you can also consult with a mouse external further isolate the issue.

  You can also run diagnostics on the touchpad from this link by going to the UEFI F2 diagnostics: http://support.hp.com/in-en/document/c03467259 please run the complete components. If any component fails, please note the failure code. This is done to determine if the problem is hardware or software partners.

  If it passes and scrolling works very well, please perform these updates. If you are still having the same problem on page F2 UEFI (screen) then you could roll back bios after performing a hard reset. Link for the hard reset: http://support.hp.com/us-en/document/c01684768

  • Please perform this step to roll back bios.  Hold down the "Windows" key and the letter "B" at the same time, then press the power also button for about 5 seconds at the same time.

  I hope this helps. I would like to know how this happens. I hope the problem is solved without hassle and the unit works very well.

  Just to say thank youPlease click the ' Thumbs Up ' button to give a Kudos to appreciate my efforts to help me. If it helps, Please mark this "accepted Solution" because it will help many other people with the same problem to get it resolved without hassle.

  Now carefully and have a wonderful week ahead.