Compaq presario c795tu model - problem IDE hard drive /disques

Similar Questions

• Installation of restore in Compaq Presario V2000 after replacing the hard drive disk

  I have a Compaq Presario V2000, I had the hard drive replaced at CompUSA.  The drive is a 250 gig to replace the original HD 40 gig.  When you load the restore of the operating system (Windows XP) disc nothing happens just a note on the ethernet controller and the media test failure then exit ROM PXE.  How to load the operating system.  I follow the procedures on the Web site?

  Thank you very much.  After a discussion at CompUSA, they decided to try another HD concert 160 instead of 250. Wallah... OS began the installation of restore disc program.  It is a problem with the new hard drive.

  Help a what to do CompUSA actually tech the problem finally.

  Thanks again!

• Presario CQ5110F: COMPAQ Presario CQ5110F adding a second hard drive and...

  Good so I took the lead when writing my original post on how to combine the two computers successfully.
  Not enough research, no question, just a little say aloud... Sorry about that.
  http://h30434.www3.HP.com/T5/desktop-hardware-and-upgrade-questions/HP-Pavilion-slimline-s3505f-amp-...

  I had little time today messing with both ' puters and discovered...
  They need a good cleaning and had.
  The noise of the Presario is indeed the fan on the radiator, it's just old and tired. Who cannot be strong in a music room; new fan may not be too expensive.
  So I decided the Presario is my starting point.

  I would add the hard drive of the Slimline as slave; they have different connectors tho.

  (1) if I just unplug the V2000 CD reader (that has the straight plugs) and use them to connect the second hard drive will I just lost my CD player? It is very good.
  (2) what parameters of rider (if any) do I need to have on each disc? Do not see outside the car Slimlines.

  I looked closer 2 slots for RAM and noticed that beside them there seems to be 2 places in addition to the Board of Directors, unused with no present holders plastic.

  (3) is it possible to add more slots and double the RAM? I would get 8 + GB and a 64-bit system end by ;~)

  Neither office seems to have the ability to run 2 monitors as is. No problem 29 "should do for now.
  Can't see a way to take the card out of the Slimline wireless and put it in the Presario. Internet not immediately necessary, hard connection cable always an option.

  All the other tips and advice on how to optimize my sytem are also welcome.
  Thank you for your time and helping an old guy handyman.
  See you soon!

  COMPAQ Presario CQ5110F (2008ish)
  Processor AMD Athlon X 2 7550 Dual Core 2.5 GHz = Socket: AM2 +.
  Card mother = Narra5 M2N68 - THE Chipset: NVIDIA GeForce 6150SE nForce 430 Socket: AM2 +.
  Memory RAM = 4 GB RAM DDR2 DIMM PC2-6400 MB/s
  = Video/graphic card nVidia GeForce 6150SE integrated graphics
  Sound/Audio = Audio integrated Realtek ALC888S
  Hard = 320 GB SATA 7200 RPM drive
  CD/DVD Player = DVD +/-R / RW 16 X SuperMulti SATA drive
  OS = Vista Edition Windows Home Premium SP1
  Power = 300w
  Case = Mid size 38cmHx17cmWx43cmL ATX

  Hard drives has no different connectors if they are both SATA specifications like other post indicated.

  There is no adjustment to make on hard disks of the rider SATAS. According to me, that one can think of the old school the IDE drives.

  ) If I just unplug the V2000 CD reader (that has the straight plugs) and use them to connect the second hard drive will I just lost my CD player? It is very good.

  The image below is a diagram for your motherboard. You have enough SATA ports to be used for the second and even a third hard drive.

  

  DDR2 memory modules can be a little difficult to source. The current generation of add-on memory is the DDR3 specification.

  Perform a Google or any search engine is your preference in the memory of the source by using the update of Compaq presario CQ5110F RAM as keywords.

• Compaq presario CQ56 103TU: upgrading laptop hard drive

  Our computer comes with a 320 GB hard drive. I would like to replace it with a larger. How can I find the larger sizes that I can use without going into what anyone other than the typical installation and the complicated transfer system? I saw a hard drive 1 TB, put on sale. Is - too big for my computer? Or maybe something in the order of 500 to 750 GB. Thank you.

  Any laptop that can take a 320 GB drive can also take a 1 TB drive.  The older player size limit was around 120 GB - and that was due to the limits dealing with old BIOS, which disappeared a long time ago.

  Also, a very easy way to replace a drive is to buy an external adapter that can connect the new drive via a USB post and 'clone' of the old drive to the new using a third-party product like Macrium Reflect.  I also use this to "clone" SDD HARD disk when I replaced the drives in laptops.

  Good luck

• 2nd IDE HARD drive problems

  Hey,.

  I'm having a problem with a 2nd drive HARD IDE, I,

  For some reason any used on my PC recognize it,.

  I have a 160 Gb SATA HDD (which is my first HARD drive with the OS on it) and a 40 GB IDE HARD drive (which is for storage, etc.)

  Now I want my second HARD drive (where is also 40 GB) of additional storage space, but my PC used to recognize both IDE, one of them at a time with the SATA HARD drive.

  The two IDE is fine and working properly I know (I ran the Tests and others), they both are recognized when put with the SATA, one at a time but not when I put all three in all

  My Pc is:

  http://support.HP.com/us-en/document/c00892923

  SATA is: Western Digital Caviar WD1600JS (160Gb) (OS = XP Pro 32-bit)

  IDE 1 is: Maxtor 2F040L0 (40 GB)

  2nd IDE is: Seagate ST340015A (40 GB)

  No idea as to why its doing this and a way to fix it?

  Thank you

  SGMAlice

  Hey,.

  Sorry its been, lived a hard time lately, not had much on my mind.

  The problem is solved!

  It may be a combination of things you suggested or the fact that I saw my PC the other day and re-installed the OS completely.

  Suffice it to say: all three now work together

  Thanks a lot for your help, you two

  SGMAlice

• XP does not recognize a second IDE hard drive.

  Summary:
  Added a PATA IDE drive so both are on the same cable.

  System information:
  IBM ThinkCentre P4 2 .66GHz (bought in 2005 approximately)
  Upgraded RAM from 1 GB to?, pin DIMM 184 form factor.
  Hard Drive IDE 1 x 40 GB - Standard - ATA-100-7200 RPM.
  Genuine XP; SP3 downloaded and installed by me.
  MT - M 8187-WBK S/N: KCGL5NB
  8187 is a type for a M50 number.

  My assumptions of hard disk:
  It is Setup to have a disk of expansion under the DVD with separate IDE cables and no doubt when both these are used you are in a primary + secondary situation.  I think that I am looking to get a configuration 'Double' where both are on the same IDE cable.

  Action:
  Removed the floppy drive and put the old HD in its place; It is the primary IDE hard drive.
  Put the new HD located under the old and attached the new cable at the same time.
  Use the power connector of the DVD on the new drive; I could so far to an extension of the extra drive Bay.
  I checked the BIOS boot menus, but could not see anything that needs to be changed.

  Problem:
  The system shows no signs of the new command.
  It still shows the floppy drive.

  I hope you can help,
  Peter

  USB is not supported, and even if that were the case, put the file on a USB drive would significantly reduce the performance of Windows.

  To speed things you can locate the swap file on a separate partition (should be the first partition, about 10 GB is more than enough) on a second hard drive.

  J W Stuart: http://www.pagestart.com

• HP 6280 t desktop computer. Can I install a 2nd IDE hard drive?

  I have a desktop HP p 6280t.  I have some old hard drives PC alternative before... all of these disks are IDE.  The current hard drive in my 6280 is a SATA.  The HP motherboard belongs 492774 001.

  I don't see how I can connect the IDE hard disk... Help, please.  Be descriptive in your explanation.

  EJD60, welcome to the forum.

  There is a SATA controller on the motherboard.  Whether you are able to install an IDE hard drive, you must install a PCI Express x 1 card IDE controller card.

  Please click on the Thumbs up button '+' if I helped you and click on "Accept as Solution" If your problem is resolved.

• Windows problem for hard drive replacement

  I am trying to replace a hard drive in a HP d530 for a science teacher as the XP is a failure. He needs the XP until I finished preparing the Windows 7 and it has data on the XP and I put Windows 7 on the new hard drive and it has 80 GB. The old hard drive Windows XP and it is a 40 GB. I had two hard drives hooked when installing Windows 7. Windows 7, the name is the C drive and disk XP the D. I tried to start the hard drive of 7 single and it gives me an error of invalid system disk. Press a key to reboot. When I have two connected hard drives, windows 7 starts very well. A computer teacher wants to clone Windows 7 for another professor of science. He said, it won't help him with two hard drives connected. How can I get on the 80 GB stand-alone installation without having to reinstall Windows 7 Windows 7. I want to disconnect the hard drive from XP and just use the hard disk 7. I have the 7 and XP on separate hard drives. They are the two IDE hard drives. I need to get the new hard drive to boot by its self and windows 7 as a stand-alone installation.

  That's good news.

  I'm so glad you took in charge.

• HP 6120 t BIOS does not recognize the second IDE hard drive connected via IDE-SATA controller

  Hello

  HP 6120 t (vista) BIOS does not recognize the second IDE hard drive connected via IDE-SATA controller. The other SATA disk and the DVD player came with the machine.

  I hooked my old 200 GB Hitachi drive via the controller. I also put the jumbers in the present as a slave. I also took the original WD drive and just connect the IDE hard drive. BIOS do not show any drive at all.

  I would try something possible at this time I have a lot of my data on the old disk.

  Thanks appreciate any suggestion.

  Try to enter the BIOS and I believe under change of Advanced menu of SATA to IDE or Enhanced.

  You need to do when you install Windows XP or you will get a blue screen and it does not start.

  Don't forget chang back when you put it in your drive home hard sata.

• Compaq presario c795tu driver needed sound... Please help me...

  Please help me... I need driver sound conexant HD smart audio 221...

  In fact, I reinstalled the XP and came to know that the sound is not...

  When I checked it... sound driver was missing some files like AUDSYS.exe and UIU32A.exe etc.

  By mistake, my friend has been uninstalled the audio driver. Then, the problem has been brought...

  2 days back I went to local compaq shop... they installed a few audio driver that works but at the same time

  Phone head and speaker that both are working constantly... means if u want to hear via head phone... pregnant also work with head phone...

  sound is through two devices...

  Please help me with this... and give me presario c795tu audio driver...

  Hello

• IDE hard drive into a portable speaker access problem.

  I got your desktop who died (power is not a replacement value).  I removed the two hard drives (IDE) and bought pens for use as portable hard drives.  I have not had any problems at all with the 'second' hard disk that I had originally put in place as a backup of data - music, photos, etc.  The problem I have is trying to access the old 'C' drive like a laptop.  I was hoping I could at least reformat and use it as additional storage.  I tried every possible rider but still cannot access this drive from my Vista laptop or my desktop XP.  The disc spins and it is "kind of recognized" by the host computer, but when I try to right click on it in "my computer" everything freezes.  I can still access it through the BACK.  I guess it has something to do with the fact that there is an operating system on the drive, but I was hoping that I could at least go enough to wipe.  Another strange thing is that when it is displayed in 'My computer' it appears as two disks-(that is to say E, F, or similar)

  I could solve this problem.  Using disk management, I was able to reformat the drive, leaving a small 4 GB EISA partition, which I was able to remove by using DISKPART.  In retrospect, it is more work that it was worth for a small car, but I now have a 120 GB drive laptop that I can use for storage of photos or other.

• HP Presario C061-220SA. Which hard drive - SATA or IDE?

  Hi guys

  HP Presario C061-220SA my daughter is dead and of course, to be a university student, she has all of her work there and no backups!

  So, now I have the laptop and BIOS utilities, checking the material, it was stated the hard drive had to be replaced.

  I'm guessing it's a disc hard 2.5 "but I'm not sure if it is not an IDE or SATA - can anyone help?

  I need to get this fixed fast and replace the drive, maybe I'll be able to recover some of its data when I chase him and connected through a USB enclosure.

  See you soon

  John

  Presario CQ61-220SA has a 2.5 Sata drive.

• Windows problem with hard drive changed from IDE to SATA connection.

  After a full rebuild (new MB, CPU, graphics and RAM) and install the new copy of Windows 7 Home, everything is great, until I try to connect an additional internal HDD. The boot and then crashes to the windows logo. Additional HARD drive is SATA, but it has already been used on an IDE connection.

  The bios recognizes the drive, but obviously, there's some kind of conflict in Windows (I think the reader can contain a backup of the previous generation system).

  System;

  MB ASUS M5A97 R2.0

  CPU AMD FX6

  Gskill 8 GB of RAM.

  Any ideas on how to fix the problem please?

  Thanks, Chris

  Usually means a player has failed/problematic

  You say sata drive but used on a connector IDE does that mean you are using a cable converter, because the type of interface is completely different, or do you just mean the parameter for the connection of the bios?

• Presario SR1913WM support 3 TB hard drive?

  My card Presario SR1913WM mother/BIOS will support a 3 TB hard drive?

  (Specifically, this hard drive.)

  If so, on expansion cards?
  (Specifically, this one and this , both by SIIG.)

  Here is the record of SR1913WM.  (I'm only curious about support for the motherboard, I do understand that there are problems with the help of > 2TiB under Windows XP and with booting from hard drives > 2TiB with either a motherboard without [rare] or any 64-bit Windows operating system not UEFI unless they are on a special expansion card.)

  I can tell you that I am now with a hard drive 3 TB * in my Compaq Presario SR1913WM under Windows XP Pro sp3 with the GPT Hitachi Disk Manager.

  As always I ran boot diagnosis * of the manufacturer of the drive before you always boot into Windows, and I got a bit scared, because he couldn't "see" (and by the speed with which he completed only tested) 801 GB; but according to an email response this morning "..." Hitachi technical support. We are currently updating the Drive Fitness Test. It is not compatible with our 3 TB drives and will not always work a criterion appropriate to this topic. »

  HDS723030ALA640 http://www.hitachigst.com/internal-drives/desktop/deskstar/deskstar-7k3000 model

  * Hitachi Drive Fitness Test 4.16 http://www.hitachigst.com/support/downloads/#DFT

• Compaq elite 8300 all in 1: Compaq 8300 allin 1 bought with HARD drive erased

  HARD drive is completely wiped and no information system have also tried the keys F11 and it too is not go... can I get HP restore disks

  You can buy all of the surgeons computer recovery discsHERE. Just put the model number - need a more complete than all in a single desktop Compaq Presario.  Is HERE IS a SAMPLE for model number CQ1-1130.  For the model that you own should be the same price.