Compaq Presario CQ4010F: Problem of block of POWER Possible on Compaq Presario CQ4010F

Similar Questions

• HP Pavilion p6-2: problems on blocking down after I installed the new power supply on a p6-2207ep

  Hi all

  B4 explaining my problem, I really don't know if I should post this in office, or material in this section of the freezes/crashes/locks but since I posted in freezing section and no results I decided to try here.

  My pc: http://h20564.www2.hp.com/hpsc/doc/public/display?docId=c03382032

  I bought a new PSU: XFX TS 550W 80PLUS BRONZE for the GPU upgrade 380 R9 I was planning to do.

  Is there some BIOS I get HP for this cause of power supply from what I read, if I not only one of the things like manufacturer reset to the factory settings may stop working... Currently, my Bios version is 7.11...

  Problems with the new power supply:

  When I closed windows 7, the first problem, the picture freezes on the screen that says "blocking windows down", I waited a bit and nothing, tried to turn off the machine while keeping down the power button but nothing to disable directly in the rear switch of the PSU...

  Second time happened a little different soomething, seconds after freezing again on the screen that says "blocking windows down" windows actually turned off and the screen is off but everything inside the computer case continues to flow fans in light of the power button / stop and was also able to close by keeping pressed power button...

  When I restart the computer, to which some time stops, and only after a few seconds, it turns...

  Also tried the GPU with the new PSU fans worked but no entry in the screen that I guess just a power supply problem.

  ATM, I'm RMA waiting to know if it is a power supply defective or not...

  Problems after the reinstallation of the original material:

  Some of the same problems when I got the new PSU remained namely:

  Windows actually stop and the screen is off, but everything inside the computer case continues to flow fans in the light of the button on / off and was also able to close by keeping the power button...

  When I restart the computer, to which some time stops, and only after a few seconds, it turns...

  What I've done so far to try to fix the problem:

  Restore windows 7 to a b4 point the hardware installation.

  Reset the BIOS

  Hard reset

  Clean boot

  Do you have a full checkdisk which means 0 KB in bad sectors...

  A complete hardware checked all tests with the HP software

  A system file check everything beautiful

  What I fear most is a faulty PSU that may have caused damage to my equipment mainly the motherboard, but could be something else entirely.

  Maybe I need a specific BIOS for that motherboard / PSU combo, but after returning to the source material, the problems remained.

  What I can do because I can only make the software tests since I don't have an extra PC to test the parts...

  Hello

  Disconnect all external devices except the keyboard and mouse when you try to solve the problem.

  Disconnect the PC and removed the CMOS battery.  Press and hold the power for 30 seconds.  Now, replace the CMOS battery and plug the PC give a TI a go.

  Your PC is not stable enough to make a BIOS update. Do not attempt to use the graphics card XFX until your PC is stable enough to make a BIOS update.

• M30X 129: problem of battery or power management road

  Hi all

  I had a lot of trouble with my laptop recently; When using just the battery I can watch it unloads and a minute, he can read about 30% or more, depending on the laptop will be beep like crazy and then go into hibernation. I put it to Hibernate at 5%. I find it incredible that the battery can lose about a quarter of its power in less than 60 seconds.

  I've updated the utility of power management using the Toshiba site, but it has not changed anything. The only time that I have the AC adapter and battery at the same time is when I charge the battery, if I'm near a power outlet and there is no need to reload, I always remove the battery.

  I read on these forums somewhere on the withdrawal of the Toshiba power management and just using windows, but I prefer not to change anything like that, as far as I'm concerned the Toshiba it should do the job! The laptop is still under warranty but my nearest authorized repair center is more than 200 miles away, so, does anyone have any ideas of what I can do or try next? I'm out of ideas...

  Cheers in advance,
  Colin

  Hi Colin,

  You don't say how old is your battery, but it is more likely to be a hardware problem with your battery rather than a problem with the Toshiba power utility.

  It seems that if one or more of the cells in your battery cannot hold its charge properly, and once the remaining cells the battery power exhaustion will fall suddenly.

  HTH

• "Symantec service framework stopped working" 'a problem caused blocking the program works correctly. Windows will close the program and notify you if a solution is removed from the privacy of available'Email

  "Symantec service framework stopped working" 'a problem caused blocking the program works correctly.  Windows will close the program and notify you if a solution is not available"

  Favorite

  E-mail address is removed from the privacy *.

  http://www.Symantec.com/Norton/support/kb/web_view.jsp?wv_type=public_web&docURL=20080917103626EN&LG=en&SEG=HHO&CT=us&PVID=nis_2009&selected_nav=5

  http://Service1.Symantec.com/support/Norton360.nsf/0/a5ae667bcb41502b6525729f002036b2?OpenDocument

  It's a Symantec/Norton problem; read the links above.

  Contact Norton Support:

  http://www.Symantec.com/en/AU/Norton/support/index.jsp

  See you soon.

  .

  Mick Murphy - Microsoft partner

• Replace the block to POWER Alienware

  Hey guys, I bought an Alienware Aurora R4 in early 2012 and the PSU is at his last breath, there problems by giving enough power when you do pretty much anything, I get the screen flicker, pilots does not and PC plant, not ideal. I know that you might wonder how well do you know this and that, I spent the time to understand and it is indeed the PSU I used the software, I checked everything manually to see if it's fine. So with that I need a new power supply, I can get a replacement? Any other feeds work with the R4s wiring?

  I would really like to hear something from maybe those who have upgraded to a better diet, I know there a good number of you who have done work on some Alienware cases. Thank you new guys and I hope to hear from some of you soon. PS sorry if this gets asked a lot I do not know this, but all the help I can get is very appreciated if.

  the only one able to work with the harness business supply Aurora are the models 1000/1100/1200 w Area - 51 longer R1, but u lose a disc hard bay in the attempt because of the length. link included below, as well as most of the material of this forum swap. Do not advice that explains how to connect your card grfx with the pattern of cable, like here:

  Upgrade of the Aurora R4 PSU.

  • http://en.community.Dell.com/Owners-Club/Alienware/f/3746/t/19627219

• a window keeps popping up that says: Windows host process (Rundll32) has stopped working - a problem caused blocking the program works correctly. Windows will close the program and notify you if a solution is available

  a window keeps popping up that says: Windows host process (Rundll32) has stopped working - a problem caused blocking the program works correctly. Windows will close the program and notify you if a solution is available

  Check if you have picked up malware in your travels.

  I see a lot of recommendations here for programs such as -

  Malwarebytes' Anti-Malware
  http://www.Malwarebytes.org/MBAM.php

  SuperAntispyware
  http://SUPERAntiSpyware.com/

  Check in safe mode.

  Vista advanced boot options
  http://Techblissonline.com/Vista-advanced-boot-options/

  See if you can isolate a possible cause.

  How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7
  http://support.Microsoft.com/default.aspx/KB/929135

• Error when you try to start the Medal of Honor Allied Assault: a problem caused blocking the program works correctly. Windows will close the program and notify you if a solution is available.

  Medal of honor allied assault has stopped working?

  This message seems to me when I start the Medal of honor Allied:

  (a problem caused blocking the program works correctly windows will close the program and notify you if a solution is available)

  Hello

  ·         How long have you been experiencing this problem?

  You can reduce hardware acceleration and check if the problem persists:

  1. right click on the desktop and choose personalize.

  2. click on display settings.

  3. in the display settings window, click on advanced settings.

  4. display the Troubleshooting tab.

  5. click on change settings.

  6 reduce hardware acceleration.

  Also try the procedure from the following link: http://windows.microsoft.com/en-US/windows7/Fixing-game-performance-problems

  Also try to check if the game works the clean boot: http://support.microsoft.com/kb/929135

  NOTE: make sure that you start the computer in normal mode after troubleshooting is done

  You can also post your questions on: http://support.ea.com/

• Media Player error "a problem caused blocking the program works correctly. Windows will close the program and notify you if a solution is available.

  Hello

  Whenever I try to play something or burn something using Media Player, I get a message.  "A problem caused blocking the program works correctly.  Windows will close the program and notify you if a solution is available.

  Help

  Jason

  No worries, go to the start screen and find the Green store icon.  When you open it will let you know if the update is available.

• PP CS5.5 has stopped working - a problem caused blocking the program.

  I have the Master Collection 5.5 and Premiere Pro decided to not start (it was fine last time I used it about 6 months ago). The start screen appears for about 2 seconds and then the message 'first Pro CS5.5 has stopped working. A problem caused blocking the program works correctly etc.

  I uninstalled Premiere Pro and re-installed from disc, but I experienced the same problem I uninstalled now again. I am aware that the disks are old enough now, and I wonder if I need to download a newer version. I found a few downloadable update files, but I didn't know what version I have to select (there are a number of version numbers, and some say that for electronic downloads) or if I need to reinstall from my records to get the update, or if updates are stand-alone programs.

  Can someone point me in the right direction to get this issue sorted?

  Another solution would be to change the CC, but I do not see the options to do this, the upgrade of my 5.5 Master Collection - and I can't see how to contact Adobe...

  Thank you

  Pete

  Hi Pete,.

  I had a conversation with them, and they said that they did not support the CS applications and showed me the forums!

  In fact, not correct. We support CS6 installation problems, just not all versions before that. Sorry, CS5.5 is a suite of older applications and we cannot provide tech support 1-1 for every piece of software ever designed. Finally, this type of support tends to move to the forums. My apologies for your inconvenience.

  You have not quite a mysterious issue going on, however. You say it worked fine before, but now it does not work. I suspect a hardware conflict, probably a video driver. You can return to an earlier version of the driver to see if that will help?

  Thank you
  Kevin

• Problems with the DC Power supply QL 355TP: I can not set the tension level

  Hello

  I'm trying to control a power supply DC via GPIB. The power supply being used is the QL355TP of society Thurlby Thandar Instruments (TTi). There are no drivers of OR to control the instruments, then I need to download and install the driver from the website of TTi: the package I installed is as follows:

  "QL - P power supplies, (including QL Series II) series pilot National instruments (Labview and CVI)"

  and I also installed the following:

  "QL - P power supplies (including QL Series II) series, IVI driver"

  So, my problem is that when I try to use the sample application of the driver 'Volts.vi DC Ouput'; defines a specific level voltage, does not work properly. The application gives no error, but it is not set the specific level voltage. However, other functions work properly, as the measure or activate the output. I tried a lot of things, but I don't know why it does not work.

  I enclose the block diagram of the application and the front panel:

  

  

  I must say that I barely control instruments using Labview and is possible that this problem would be because I did not consider things basic and mandatory.

  Any help is appreciated.

  Thank you.

  p.s. Try to replace the decimal comma to period. It is possible that the driver does not correctly handle the comma.

• Problem with blocking to the bottom of the window.

  I have a problem with my laptop, when I stopped the Windows Xp sp3 professional, he cant turns off. Blue screen Windows is blocking down... and stop on this screen. To disable I must press on & press and hold the power button / stop.

  Which can be a problem?

  Did you get that started after the installation / uninstallation of a whole new software? You can also checkhttp://support.microsoft.com/?kbid=307274 for more information...

• Problem of management of power with the Satellite S2430-402

  Every time is start my laptop, I get a message saying "%1 is not a valid Win 32 application" under the heading "E-power", thus the Toshiba power management does not load. I tried to uninstall and reinstall the software from the cd, but it does not work, and I still get the message.

  The problems began after I installed a program called Ghost Surf 2005 and ran for the first time. Since then I uninstalled but still has problems. I am running Windows XP operating system.

  Can anyone help?

  Hi Dan,.

  It seems that the software corrupted a file which is responsible for the powermanagement! There is what we call common files and it can be replace a file, the installation of Ghost surf!

  You can try to solve it with the Windows XP system restore when you set a restore point! Back to a restore point that was resolved before installing the software!

  Hans Bye

• Block of power SUPPLY HP Slimline s3710t

  I have a HP Pavilion Slimline s3710t, it runs Vista Home Premium (32 bit).  Power is out on this subject a few months when I moved.  It worked fine the day we moved in, just before I had to stop it and unplugging everything.  Come to our new home and went to hang on to the top and NOTHING.  Taken to be extracted and discovered that food was shot, the guy he has connected to a * test * PSU and it came right on.  He told me that I would need a new and that because my computer is a Slimline I must get a * special * power supply.  I took mine to my computer and did a search and it was not very useful because I can not find the SAME block power, but at the same time, all the power supply that are * recommended * because my computer don't LIST my computer as they work with.   I need a new PSU and I have NO idea what kind I need / can use.  I need one that will run my computer and my games pretty well, but I don't have the money to buy an EXPENSIVE one.

  Hello

  You could try Ebay for $40 or HE winklefor $70.

• Satellite Pro A10 - space problem - strange behavior of power key on

  Hello world

  Point I turn on my pc (power - on password), space starts feeling as if the space key is pressed, but it's not. I bought a new Toshiba keyboard, installed but the problem persists! It seems that the problem doesn't lie with the keyboard, but something else I was unable to understand.

  Could someone please help.

  Thank you.

  PS: I installed the software key remapper to disable the SPACEBAR I can at least use my laptop. Then I copy and paste the character 'space' - ThisIsHowIWroteThisWholeEmail - HopeOneCanImagineThePain

  Hello

  Have you tested with external keyboard? Is the the same keyboard behavior?

• Power problem (battery-operated same power supply cord is plugged)

  Hello!

  I again (only a few months) HP ProBook 6550 b. Recently, I noticed strange problem.
  I don't understand if it's a hardware or software problem.

  The problem: sometimes when the laptop starts up I see that it is running on battery power cord is plugged.
  Solution: I need to disconnect, and then again once (sometimes several times) to see the icon "plugged in, load" once again.

  I don't know if it's related, but... Mainly, I start my computer on the Windows environments from process Plug and battery.

  Provided HP with Windows 7 Professional x 64 preinstalled.
  Someone at - it similar problem or someone knows what causes this problem?

  If you slightly press the power adapter were it connects to the computer is laptop power detect AC?

  try saving the Bios on your click Law Office and run as administrator