Compaq Presario CQ62-412NR does not start. Caps lock flashes.

The LED caps lock flashes repidadly with long breaks between each blink, the wireless light and constant and the adapter LED is steady. I read blink codes and determined, he was the processor, but the problem persists after him substituting a known good. I finished the resets power to clear the bios before and after the change of the CPU. I also tried to replace the RAM. Anyone here have a clue whats going on?

This looks like a problem with the motherboard if you already replaced the CPU and RAM.

It would be probably cheaper to replace the unit at this time only so, fix it or replace the motherboard.

Tags: Notebooks

Similar Questions

  • Compaq Presario CQ62-a20EC does not load


    OK, the original (defective) power adapter details are:

    Pei/n: 608425-003

    -spare part: 609939-001

    The other of Presario CQ61-315EC that I used for the test is:

    Pei/n: 519329-002

    -spare part: 463958-001

    Part Locator does not contain my country (Slovakia). I played with him in selecting other nearby countries, but it has not helped me a lot. I contacted three local stores for proper AC adapter and I already bought a.

    p/n: 608425-001 - this has a different suffix as the original

    -spare part: 609939-001

    CQ62-a20EC works correctly with both above mentioned functional power supplies.

    ==

    There is another problem that appeared in fact after the update of the BIOS (F.8-> F2. (B).

    (Press F2 during POST) diagnostic-> battery test system:

    -F.8 BIOS with defective power supply = > has failed with the message "no adapter not connected" - this seems reasonable

    -BIOS f.2bs with defective power supply = > failure with "primary - replace (30)", failure id: 0GFM7R - 52T 693 - 9XL03G - C0E903 - sounds strange and I do not expect such different error after BIOS update

    -BIOS f.2bs with the new power adapter = > failure with "primary - replace (30)", failure id: 0GFM7R - 52T 699 - 9XL03G - C0E903 - please see that failure is different

  • Compaq presario cq57-339WM does not recognize the drive as a bootable disk recovery

    Compaq presario cq57-339WM does not recognize the drive as a boot drive recovery, I'm sorry people, I searched and I entered the job in New York as a matter of research. Operating system is 7 Home premium. Hard drive went bad, so I rplaced with new. I have had I have windows image backup, but the wizard could not find the hard drive. I ordered the HP poped the first of the two recovery disks, but the machine does not recognize the drive as a bootable disk recovery. I did factory retrieve records a large number of times on computers with different operating systems and have never seen this. TNA

    Randy Rich

    I found this on PC world. I downloaded everything I need, I hope. I tried not to build the disk again. I need some rest and sleep. Stay tuned for more develonents. Here is the link http://www.pcworld.com/article/2364269/how-to-reinstall-windows-like-a-pro.html?page=2

  • HP Pavilion dv6 does not start. CapsLock flashes 3 times.

    Hp Pavilion dv6 , I bought about 11 months ago. When I tried to turn it on today morning, it didn't start and the light caps lock flashes 3 times. I searched the Internet and discovered that it is a memory problem. Is there a solution to this problem so that I can fix it in the House?

    Hello

    Try to remove and re-seating memory module - the procedure is detailed from Page 68 of your & Maintenance Guide.

    Failure to correct the problem, as your laptop is still under warranty, your best option is to contact HP and make arrangements for this repaired under warranty - if necessary, you can check the status of your warranty here.

    If you live in the United States, contact HP here.

    If you are in another part of the world, begin here.

    Kind regards

    DP - K

  • sleekbook envy 6: laptop won't start, caps lock flashing 3 times

    I want to 6 sleekbook and all of a sudden that it does not start and the caps lock flashes three times I already saw the code flashing and tried to rest the memory but it still doesn't work, I ran in problems with the laptop before the blue screen, but it was fixed its own I think

    Dear customer,

    Welcome and thanks for posting your question on the Forum of Support HP

    It seems that your laptop has a blank screen and a blinking/flashing CAPSLOCK all the time

    If the Capslock LED flashes 3 times this means "Non-functional memory error", in order to solve the problem, replace the card memory

    Note: If you are comfortable open Notepad, you can check how much you have memory module. If you have 2 sticks of memory, you can test one at a time on the two slots individually to check if the fault is with the module module slot or memory memory your laptop [repeat the same steps to test another memory module]

    If you find the above steps difficult and that it is a hardware problem and I recommend you contact HP Support by phone for further assistance immediately to get your diagnostic Notebook and repaired by an authorized HP Certified Engineer

    You can also check your warranty here to check the status of the guarantee

    Hope this helps, for other queries in response to the post and feel free to join us again

    * Click on the star of CONGRATULATIONS on the left to say thank you *.

    Make it easier for others to find solutions by checking a response "Accept as Solution" if it solves your problem.

    Thank you

    GBL84

    Although I am an employee of HP, I speak for myself and not for HP

  • Recovery Manager cannot restore Presario CQ56 & system does not start, the error BOOTMGR is missing

    1. number and product name

    Compaq Presario CQ56

     

    2 operating system installed (if applicable)

    Windows 7

     

    3. error message (if any)

    in the error log:

    Your hard disk (result-failure) id # UAMBXQ - 5H06AK - XD003F - 618U03 - DISK 1

    Start (result-failure) id # UAMBXQ - 5H60AK - XD003F - 40G 403 MEMORY MODULE 2

     

    4. all changes made to your system until the problem occurred

     

    There is no change made to the computer, before the restoration of what the computer should start, however, it would freeze once the system was running. Restarting the computer didn't help, and when I tried to restore to an earlier point, he stated that it was impossible to complete the restore. I tried the factory reset, however, it gave me an error message: "Recovery Manager is unable to restore your computer by using the original image. Please contact HP support. Error code: 0xe0ef0003. When I tried to restart the computer later, it gave an error message: "BOOTMGR is missing, press Ctrl + Alt + Delete to restart» How can I fix it?

    305 error refers to a failing hard drive. You will need to replace the hard drive.

    You can check the status of your warranty here.

    If you do not want to repair the laptop you need to contact HP support. If you are in the United States / Canada you can give them a call at 1-800-474-6836. For other countries you will need to visit this site.

    If you do not want to repair the laptop you I can provide useful information, but I'm going to need your product number. This document contains instructions to find the product number.

    I'll keep an eye out for your answer.

  • Presario cq60-224nr does not start, cannot recover

    Hi all

    I'm trying to reinstall Vista on a presario cq60-224nr friends.  It won't start and F11 will not start up the system recovery.  I can't be able to know how to order recovery disks.  Can anyone help this.  ]

    Thanks in advance

    Nila

    I was able to download a copy of Vista and had check the key on the phone, but everything is good and my friend is a happy camper.  After that all I found the recovery partition, still don't know why it wouldn't work.

    Thanks for any help he

    Nila

  • Compaq Presario turns on but not start

    Product: HP Compaq Presario
    Model: SR5250NX
    OS: Windows Vista

    Symptoms: When you press the power button, all the lights come on as expected. However, a slight popping noise that sounds as if it is coming from the hard drive will ensue. The monitor, mouse and keyboard are not recognized despite being plugged in, even if the speakers are always lit. It is a problem, I am back after a journey of four days out of town, and I heard the internal fans speed up just from time to time for months. I guess this thing is fried, but I hope it can be fixed. Thank you.

    This

    http://support.HP.com/us-en/document/c01443366

    says 1 blink = bad processor. Sorry Charlie, I'd scrap it.

  • RE: Compaq Presario 732US, NIC does not work after upgrade to Windows XP SP3

    Yes, it's an old.  Compaq Presario 732US - care.  <>

    OK reformatted to give to my sister.  Had to manually installed Windows XP SP2 because the verson reformat is so update the old windows would not work with her.  After graduating on windows, update was very well and made a 140 update article.  Installed everything fine.  restarted and did windows update again and it came with SP3, which has installed fine.  EXCEPT after restarting, my network card went caput.  Said my ethernet is unplugged little matter what I do.

    So I unplug and put in another computer without touching anything and it works fine.  So the problem is with the Compaq Presario 732US.  I guess that I need drivers compatible with Windows XP SP3.

    Any idea where I can get them for such an old laptop?  Which ones to get? If I should take off just SP3 and not to date him? And if the pilots there was even the answer?

    Thank you in advance to any of you out there who can help meh.  :-)

    Try to use Device Manager, right-click the network card and choose uninstall. Restart the laptop to see if XP can install a working driver.

  • HP Pavilion dv7-4065dx does not start with continuous flashing capslock

    Hello

    I have a HP Pavilion dv7-4065dx laptop with Windows 7 64 bit that won't start or go to the Bios screen.  When the laptop is turned on, you hear the fan from the system start, start button / stop brighter lights and the caps lock button starts to Flash continuously once every three to four seconds.  The activity of the disc is also light on but with no flashing red.  No changes have been made to the laptop and it worked perfectly well a few hours earlier.  I tried the hard reset of the computer and the reinstallation of the memory cards, but the laptop would be still not start.  Any help to determine what the problem is with the computer would be greatly appreciated.  Thank you.

    HP Pavilion dv7-4065dx

    Product # WQ861UA #ABA

    It does not appear that a hardware problem has occurred.

    After reviewing the document for the blink code, it seems that the processor does not have.
    http://goo.GL/ipoGs

    A defective processor can be repaired by a local PC store, but I highly recommend you contact the HP support by phone to see what options are available. HP repair center would be able to identify the appropriate components that will need to be replaced in the rare case that the test gave flashing evil code.
    The number for the United States and the Canada is 1-800-474-6836.

  • Portege M100 does not start - power light flashes orange

    Hi all

    I have a Portege M100.
    Since ysterday, the computer does not boot. When I push the power button, I hear the noise of the fan starts working, but nothing else happens. The power light continues to blink in orange.
    I removed the battery and tried to turn on the computer with the AC adapter is plugged in, but nothing changes.

    Any ideas on what could be the problem? I would appreciate help,
    Thanks in advance

    Yalin

    Hi mate,

    could possibly be the RAM, so please check the RAM modules and remove 1 module if you have 2 of them installed.
    Otherwise, I check if some another module of RAM is available and install the module of well known work. If this is not sufficient then I strongly recommend you to bring your machine to a service partner chartered for a balance of health/repair of equipment.

    Please give some information about your situation...

    P.S.: you can try to remove the battery and AC and leave the machine without power for about 24 hours. Maybe it helps?

    Welcome them

  • x 61 does not start from usb flash drive

    I don't know that I did several times before, but for some reason any my x 61 does not allow me to boot to a usb flash drive, I use normally to install the operating system.

    Any suggestions what might be wrong and what I could do about it?

    I should mention that USB is enabled in the BIOS and usb flash drive install works on other computers.

    Update seems to be an incompatibility with wintoflash, I used the Microsoft DVD/USB tool and it starts the flash player and finished the installation. Strangely the wintoflash installation worked fine in a HP dv3000.

    Consider this resolved.

    Wow I never saw your post until that earlier.

    Situation is resolved in the first post

  • Vista does not start after BIOS flash

    I recently flashed my BIOS for my Presario SR5152NX by Vista after having downloaded the file directly following from the HP site:

    http://h10025.www1.HP.com/ewfrf/wc/softwareDownloadIndex?softwareitem=PV-66758-1&LC=en&DLC=en&cc=us&product=3436821&OS=2093&lang=en

    He seemed fine, because he then asked me to restart my PC, I did.

    When it restarts, BIOS seems to be fine but once, he's trying to get into windows Vista, it will NOT start, and instead, I get a BSOD with the following STOP error message:

    STOP: 0X0000007B (0XF789E640, 0XC0000034, 0X00000000, 0X00000000)

    I tried searching for this error, but I do not get a clear answer to what it means.

    In addition, by choosing 'use last known Configuration' always produces the error, and I can't get in any security mode in the start menu.

    I can't enter in Vista, please help.

    I have solved my problem, but please keep this up for the other reference...

    It turns out that the error has to do with a "BOOT DEVICE" error. Once I read that I feared it might be a faulty drive. This was not the case.

    It seems that after the BIOS has been flashed, he changed the order of loading on my readers, and so it hurts than as a master. I guess expected Vista are on it and wrong. What I had to do was go in the motherboard configuration by pressing F10 on the diagnostic screen, and I had to spend my disk drive to configure the Vista disc as the main (has priority on the others), using the + and - keys on the numeric keypad.

    EUREKA, now charge well Vista again and the BIOS is updated correctly.

  • Satellite Pro 6100 does not start - power light flashes

    Hello

    I have a Satellite Pro 6100 when I press the power button and HDD lights up briefly then powerlight blinks.
    It seems to Flash a pattern: on (2 sec) flashes (2 seconds) then off (about 8 times)

    What he told me? No fan, no display no hardrive is active.
    Food is ok because it load battery.
    I bought it as it would be something easy to fix ideas?

    Hello

    It sounds bad
    Generally, the power led will blink due to a malfunction of the equipment.
    The LED provides a microcode and only the technician can read this code.
    A common user is not able to read.

    Maybe you'll be able to read this code, but you won't find any description about the meaning of the code.
    I recommend you contact the technician in your country

    But try this:
    Remove the battery and unplug the AC adapter.
    Wait severla times and then plug in the battery and plug in the AC adapter.
    If this does not help, you have aks, a complementary technician...

  • Tecra A8 - does not start, led is flashing with hex message

    Hello

    My computer will not start and there is a flashing orange led light...

    There are * short 4 *, then * 4 long * light

    ==> in hexadecimal: * 0F *.

    But I have found no documentation on the * led error codes *...

    Help me please!

    Hello

    > ==> in hexadecimal: 0F
    You are right.

    > there are 4 short and then 4 fire long
    That would mean: 0000 1111
    Due to the least significant bit, must read this by behind: 1111 0000-> F0H

    Unfortunately, there is no document published in the Toshiba page on error code meaning
    I guess only the Toshiba ASP (certified partner) might provide these details and information.

    I would recommend so get in touch with the local ASP to get some information about the error.
    But to be honest, these errors are mainly related to a question on the motherboard and in this case mobo must be replaced.

Maybe you are looking for