Compatibility problem of motherboard with the new GPU [h8-1214]

Similar Questions

• Problem blackBerry Smartphones with the new version of Windows Live Messenger 2.5.30

  I HAVE A BB 8900; WEEKEND LAST I DECIDE TO UPGRADE TO THE NEW VERSION OF WL MESSENGER 2.5.30; AFTER THE UPGRADE, I CAN'T CONNECT TO THE SERVER OF WLM. ALWAYS APPEAR THE ERROR MESSAGE FOLLOWING: "CONNECTION (65) ERROR: PROBLEM RECEIVING DATA FROM TEH SERVER.»

  Finally I could connect with Windows Live Messenger 2.5.30

  I got a solution the following steps:

  (1) options > advance Options > Applications. Remove the WLM 2.5.30 application

  (2) options > advance Options > Service Boks: remove all files associated with WLM (any version)

  (3) options > advance Options > host Routing Table. Register now

  (4) batt Pull Reboot

  (5) reinstall WLM 2.5.30

  (6) options > advance Options > host Routing Table. Register now

  That's all!

  Thank you all to help me.

• Satellite C660-28 d - problem "Load driver" with the new HARD drive

  I have a Toshiba Satellite C660-28 t.

  The hard drive has failed. I called Toshiba Support who send me a replacement.

  However in the meantime I was going to put in my spare hard drive and do a fresh install of another operating system that I have a spare for (Win 7) key.

  However, I can't past the screen "Loading Drivers" as the laptop came with driver disks.
  I can't find the drivers on the Toshiba site (I tried some drivers intel which I thought were good, but he says they were not signed and all comes down to the loading screen drivers).

  I have made the recovery discs, but obviously can not use them on the new hard drive as it doesn't have the recovery partition.

  Any ideas on where I can get the proper drivers from?

  Thank you

  > I made the recovery discs, but obviously can not use them on the new hard drive as it doesn't have the recovery partition.

  If you have a recovery disk using Toshiba preinstalled recovery media creator tool, you just have to boot from that disk to begin the installation.

  More info: all the recovery disk for Toshiba Europe, models of laptops can be ordered here:
  http://backupmedia.Toshiba.EU/landing.aspx

• Problems of networking with the new configuration

  I install a new system and have a few questions that have been bothering me and can not find answers to.

  ESX Server #1 has a Service Console to 172.25.10.1 and this is the IP address of the area of physics.

  I have a box on its own subnet/switch (vSwitch1) iSCSI using 192.168.x.x address and it is connected via a switch to two ports on each ESX box.

  What I don't know, it's what to use and where to put the gateway on this vSwitch1.

  Sorry if this question seems basic, but this is my first kick in the implementation of a system.

  Thank you

  Rob

  Hello

  Are you talking about the default gateway? In this case, the default gateway remains with the first port of SC. You don't need to configure any 'bridge' for anything on vSwtich1. Your vmkernel gateway remains with VMotion.

  You should be able to ping and vmkping your iSCSI host, it's everything you need to make this work.

  Best regards

  Edward L. Haletky

  VMware communities user moderator

  ====

  Author of the book "VMWare ESX Server in the enterprise: planning and securing virtualization servers, Copyright 2008 Pearson Education.»

  SearchVMware Blog: http://itknowledgeexchange.techtarget.com/virtualization-pro/

  Articles of blue Gears - http://www.itworld.com/ and http://www.networkworld.com/community/haletky

  As well as virtualization at http://www.astroarch.com/wiki/index.php/Virtualization Wiki

• photosmart all-in-one problems 5200 impression with the new Dell running windows 8.1

  have a photosmart C5280 All-in-one I used with a computer that is running windows XP, it worked fine. Bought a new computer running windows 8.1, printer don't print very well at all. It prints the page after page, one or two lines of hyroglifics tile view deleted I canceled the print document to stop using paper. I uninstalled the printer software and reinstalled from website of HP software to run with windows 8.1 still does not work.

  I think it made me print again. I had to uninstall the full features software and loaded the driver only. I could not full features software to load completely, then I loaded the driver only and it seems to work okay thanks for the help.

• Windows 7 does not start with the new msi motherboard

  Yesterday, I bought a new motherboard, processor and 8g of ram in my computer. After all what adjustment and replacement of my old motherboard with the new, I started my computer to find that Windows 7 unbootable not. Instead of windows 7, I get the screen click on BIOS II (2). The configuration screen allows me to launch Winki but not Windows 7 because it was not found. The motherboard came with a utility disk drivers msi and AMD chipset which, when inserted in my hard disk, loads up to Winki. This version of windows 7 (Home Premium 64-bit) came pre-installed with my old mother/computer(Thus, I do not have the windows 7 installation disk) card. Is there a way I need to activate Windows 7 on my new motherboard?

  Hello

  Well, you have some problems. First of all, with a new motherboard you need a new copy of Windows - not only the DVD, but a whole new product key must be purchased. It's just the terms of the license: a new motherboard is equivalent to a new computer, and each computer must have its own copy of Windows.

  So where you buy your copy of Windows 7, I would make sure that it came with a DVD image. Otherwise, you can tell us which version of Windows 7 you (will) actually buy, and we can send you a link to the copy of the DVD for this version of Windows 7.

  To purchase a copy of Windows 7 you can check Newegg.com, here: http://www.newegg.com/Product/ProductList.aspx?Submit=ENE&DEPA=0&Order=BESTMATCH&Description=windows+7&N=-1&isNodeId=1 .

  I hope that answers your question.

  Kind regards

  BearPup

• will I have problems if I replace the OEM motherboard with a new?

  Someone at - it successfully system OEM motherboard replace?

  I'm fixing a child 6 years out of warranty HP m7160n Media Center PC with a motherboard failed.  If I replace the MB with a new one, I have software problems?  My goal is just to make a quick motherboard replacement and restore the computer to the owner with that little pain as possible.  What I don't want to do, is to have spend $90 (HP parts store wants $250) on a replacement motherboard and then have to deal with software problems then currently installed programs or the operating system.  It did not come with a Windows Media Center CD, everything is in the HP recovery partition the existing drive.

  It's my understanding that even though I am an end user, I should have no problem getting it registered/validated until I replace the motherboard with the same make and model that came in the original system.  Thanks in advance for your answers.

  A motherboard with like-for-like replacement should be no. emits either with software, drivers etc although you'll probably have to revalidate.

  Problems arise only if the new hardware is substantially different from the original, in particular with the chipset of the card. That being said however in many cases you should be able to boot and install the drivers required during the initial start-up. The only exception is the player interface as this may generate a blue screen INACCESIBLE_BOOT_DEVICE and the only way around this is to pre-install the new drivers on the old system before the change, though if the reason for this change is a dead motherboard that does not help.

  I once replaced a mobo with a failed IDE port by plugging a PCI one which enabled him to start, install the drivers for the card, install the drivers for the new Board of Directors and then replaced the Board of Directors.

  Regarding the licensing issues, it's a moot point on how you can replace before it ceases to be that a repair is disabled so the EULA. I saw someone claims that he could not get a direct replacement mobo a generic would not fit the case of mark and so it "replaces" the case as well. In other words it did take out the HARD drive and put it into a new clone system. Not permitted under this EULA.

• BSOD when trying to install Win7 64 bit with the new motherboard

  Hi all

  I have the following BSOD problem:
  I installed a new motherboard in my system (a MSI P43 C51). Before that, I got a Gigabyte G41MT-S2P. The rest of the configuration is: Q9650, Thermaltake truespirit 90 cooler, 2 x 4 GB DDR3 1333, GTX 470, 750W PSU, case name, SATA HDD 500 GB, Windows 7 64 bit.

  Well, the problem started when I tried to boot into windows with the new motherboard: I got BSOD 1 second after windows starts loading. I thought... new motherboard, install new windows, so I tried to install windows 7 64 bit DVD and USB stick, I get the STOP: 0x0000000A error during installation. I changed the HARD drive, thinking that it could be a bad sector problem, but no, the other hard drive behaved exactly the same thing. I got BSOD at 40% extraction, extraction of 90% and for the moment "Complete the installation..." ». I also tried to install with the stick of memory only one, spent between ports, everything. The material I have works, as I played on my PC every day in the last month and received no. BSOD, also had a small overclock the CPU and the GPU (100 MHz on the processor, that the old motherboard supported more than 343 fsb and about 100 MHz on the GPU). It was stable, no errors, no nothing.

  My thoughts are only, after asking some knowledge that work in computer support, it could be a problem of version of the BIOS (BIOS is 2005..) and the fact that my Win 7 installation kit is without Service Pack 1 (a colleague told me that he had this problem for the PC more than once and after trying to install SP1 It went smoothly and without errors)

  I just got a new "blank" DVD of Win 7 64 bit with SP1. What I'll try today is to Flash the bios with the latest version and install the OS on a HARD drive new, sealed. He could not be my system components, because they are compatible and they worked 1 day before with no problems! I have literally NO IDEA what could be the problem. Today, I'll try the installation of the new DVD and with the new version of the BIOS. If this does not work, I have no idea what I can do... It is a sucky situation.

  If you have any suggestions, please, don't keep it to yourself :-D

  Thank you!
  Alex

  Hello

  See this thread for more information on using BlueScreenView, MyEventViewer and other methods of
  Troubleshoot the BlueScreens - top two responses.

  http://social.answers.Microsoft.com/forums/en-us/w7repair/thread/8df6485a-50cc-4cdc-BE3E-0f05c7745117

  ==============================================

  References to Vista also apply to Windows 7.

  Drivers could be at fault, however the problems of disk or security/antivirus/antispyware products are
  just as likely to be the root cause that they can force a driver to corrupt or go out of bounds.
  The video driver or something affecting it would be questionable.

  At the end of this message, I'll post a bluescreen generic and in the next convenience store
  How do to update the drivers and BIOS but also to check memory message.

  -----------------------------------

  BCCode: 0a 0x0000000A

  Cause

  This bug check is issued if the memory paged (or invalid) is accessible when the IRQL is too high.

  The error that usually generates this bug check occurs after the installation of the faulty device driver or service system, BIOS.

  If you encounter a bug 0xA control during the upgrade to a later version of Windows, this error can be caused by a device driver, system service, an anti-virus or a backup tool that is not compatible with the new version.

  Solve the problem

  If a kernel debugger is available, get a stack trace.

  To resolve an error caused by the faulty device driver or service system, BIOS

  1. Restart your computer.
  2. Press F8 to character-based menu that displays the choice of operating system.
  3. In the WindowsAdvanced Options menu, select last known good Configuration . This option is most effective when a pilot or a service is added at a time.

  To resolve an error caused by an incompatible device driver, system service, virus scanner, or backup tool

  1. Check the system log in Event Viewer for error messages that may identify the device or driver that caused the error.
  2. Try disabling the cache in memory of the BIOS.
  3. Run the diagnostics of equipment provided by the manufacturer of the system, in particular the scanner memory. For more information about these procedures, see the manual of your computer.
  4. Make sure that the latest Service Pack is installed.
  5. If your system has cards (SCSI) small computer system interface, contact the card manufacturer for updated Windows drivers. Try to disable sync negotiation in the SCSI BIOS, check the wiring and the SCSI ID of each device and confirming the proper termination.
  6. For devices (IDE) peripheral electronic integrated, set the built-in as only primary IDE port. Also, check each IDE device to the right setting master/slave/stand alone. Try to remove all IDE devices except for the hard drives.

  If the message appears during installation of Windows, make sure that the computer and installed devices are listed in the list of the products tested Microsoft Windows market.

  Comments

  Before upgrading to a new version of Windows, remove all third-party device drivers and system services and disable any antivirus. Contact software manufacturers for updates of these third-party tools.

  BCCode: 0a 0x0000000A<-- read="">
  * 1025.html http://www.faultwire.com/solutions-fatal_error/IRQL-not-less-or-Equal-0x0000000A-

  ==================================================================

  General troubleshooting BlueScreen to use with the methods above.

  Look in the Event Viewer to see if something is reported on those.
  http://www.computerperformance.co.UK/Vista/vista_event_viewer.htm

  MyEventViewer - free - a simple alternative in the standard Windows Event Viewer.
  TIP - Options - Advanced filter allows you to see a period of time instead of the entire file.
  http://www.NirSoft.NET/utils/my_event_viewer.html

  -------------------------------------------------------------------------

  Also this, so you can see the probable bluescreens.

  Windows Vista restarts automatically if your computer encounters an error that requires him to plant.
  http://www.winvistatips.com/disable-automatic-restart-T84.html

  -------------------------------------------------------------------------

  Here are a few ways to possibly fix the blue screen issue. If you could give the blue screen
  info that would help. Such as ITC and 4 others entered at the bottom left. And all others
  error information such as codes of STOP and info like IRQL_NOT_LESS_OR_EQUAL or PAGE_FAULT_IN_NONPAGED_AREA and similar messages.

  As examples:

  BCCode: 116
  BCP1: 87BC9510
  BCP2: 8C013D80
  BCP3: 00000000
  BCP4: 00000002

  or in this format:

  Stop: 0 x 00000000 (oxoooooooo oxoooooooo oxoooooooo oxooooooooo)
  Tcpip.sys - address blocking 0 x 0 00000000 000000000 DateStamp 0 x 000000000

  It is an excellent tool for displaying the blue screen error information

  BlueScreenView scans all your minidump files created during 'blue screen of death '.
  hangs and displays information about all accidents of a table - free
  http://www.NirSoft.NET/utils/blue_screen_view.html

  BlueScreens many are caused by old or damaged, in particular the video drivers drivers however
  There are other causes.

  You can do mode if necessary safe or the Vista DVD command prompt or
  Options recovery if your system is installed by the manufacturer.

  How to start on the System Recovery Options in Windows 7
  http://www.SevenForums.com/tutorials/668-system-recovery-options.html

  You can try a system restore to a point before the problem started when one exists.

  How to do a system restore in Windows 7
  http://www.SevenForums.com/tutorials/700-system-restore.html

  -------------------------------------------------------------------------

  Start - type this in the search box-> find COMMAND at the top and RIGHT CLICK – RUN AS ADMIN

  Enter this at the command prompt - sfc/scannow

  How to fix the system files of Windows 7 with the System File Checker
  http://www.SevenForums.com/tutorials/1538-SFC-SCANNOW-Command-System-File-Checker.html

  How to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe) program
  generates cbs.log Windows Vista (and Windows 7)
  http://support.Microsoft.com/kb/928228

  The log can give you the answer if there is a corrupted driver. (Says not all possible
  driver problems).

  Also run CheckDisk, so we cannot exclude as much as possible of the corruption.

  How to run the check disk at startup in Windows 7
  http://www.SevenForums.com/tutorials/433-disk-check.html

  -------------------------------------------------------------------------

  Often drivers up-to-date will help, usually video, sound, network card (NIC), WiFi, part 3
  keyboard and mouse, as well as of other major device drivers.

  Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
  http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htm

  Installation and update of drivers to 7 (update drivers manually using the methods above is preferred
  to make sure that the latest drivers from the manufacturer of system and device manufacturers are located)
  http://www.SevenForums.com/tutorials/43216-installing-updating-drivers-7-a.html

  How to disable automatic driver Installation in Windows Vista - drivers
  http://www.AddictiveTips.com/Windows-Tips/how-to-disable-automatic-driver-installation-in-Windows-Vista/
  http://TechNet.Microsoft.com/en-us/library/cc730606 (WS.10) .aspx

  -------------------------------------------------------------------------

  How to fix BlueScreen (STOP) errors that cause Windows Vista to shut down or restart
  quit unexpectedly
  http://support.Microsoft.com/kb/958233

  Troubleshooting Vista Blue Screen, error of JUDGMENT (and Windows 7)
  http://www.chicagotech.NET/Vista/vistabluescreen.htm

  Understanding and decoding BSOD (blue screen of death) Messages
  http://www.Taranfx.com/blog/?p=692

  Windows - troubleshooting blue screen errors
  http://KB.wisc.edu/page.php?id=7033

  -------------------------------------------------------------------------

  In some cases, it may be necessary.

  Startup Options recovery or Windows 7 disk repair

  How to run a startup repair in Windows 7
  http://www.SevenForums.com/tutorials/681-startup-repair.html

  How to start on the System Recovery Options in Windows 7
  http://www.SevenForums.com/tutorials/668-system-recovery-options.html

  How to create a Windows 7 system repair disc
  http://www.SevenForums.com/tutorials/2083-system-repair-disc-create.html

  I hope this helps.

• Microsoft cares if I use my old OS OEM with the new motherboard?

  I am building a newish computer; Microsoft cares any longer, if I use my old OS OEM with the new motherboard? All of the previous answers to this question are all about 2011 are resolutely "affirmative", they care. I know that Microsoft has had a change of heart (at least I think) regarding their operating system. With the upcoming free update, I was hoping I could recycle my Windows 7 64 bit, an increase in the time up to 10 comes out.

  Thank you.

  Drew

  The OEM of Windows 7 versions are identical to the versions commercial full license with the following exception:

  -OEM versions don't offer any free direct support from Microsoft technical support Microsoft

  -OEM Licenses are tied to the computer first you install and activate it on

  -OEM versions allow all hardware upgrades except for an upgrade to a different model motherboard

  -OEM versions does not move directly from an older Windows operating system

  What is OEM software? :
  http://support.Microsoft.com/GP/oemsupport_1/en-GB

  Licensing FAQ:
  http://www.Microsoft.com/OEM/en/licensing/sblicensing/pages/licensing_faq.aspx

  If its licensed manufacturer OEM System you bought, you could probably get away with the re-activation by telephone. You can always give it a try.

  How to activate Windows 7 manually (activate by phone)
   
  1) click Start and in the search for box type: slui.exe 4
   
  (2) press the ENTER"" key.
   
  (3) select your "country" in the list.
   
  (4) choose the option "activate phone".
   
  (5) stay on the phone (do not select/press all options) and wait for a person to help you with the activation.
   
  (6) explain your problem clearly to the support person.
   
  http://support.Microsoft.com/kb/950929/en-us

• I need to replace a motherboard with a new another brand, what files or drivers that I need to delete not close up with problems starting in windows 7 pro oem

  I need to replace a motherboard with a new another brand, what files or drivers that I need to delete not close up with problems starting in windows 7 pro oem current motherboard works but is old and has problems with heat. Not worried about having to re-record software am just worried starting problems

  Friday, October 19, 2012 19:03:30 + 0000, * address email is removed from the privacy * wrote:

  I need to replace a motherboard with a new another brand, what files or drivers that I need to delete not close up with problems starting in windows 7 pro oem current motherboard works but is old and has problems with heat. Not worried about having to re-record software am just worried starting problems

  Two points:

  1. it is unlikely that your current installation would work if
  you have changed motherboards. You need to reinstall itself.

  2 but you cannot use your current copy of Windows if you change
  motherboards, not even if reinstall you it cleanly. The largest
  disadvantage of an OEM version, is that its license it binds permanently
  the first computer, it is installed on and Microsoft believes that
  If you change the motherboards, another computer. It can never
  legally be moved to another computer, sold or transferred (except with)
  the original computer). If the computer dies or is stolen, your
  license dies with him.

  Ken Blake, Microsoft MVP

• My iPhone 6 installed 10.0.2 stops when it gets to 40% of autonomy.  In addition, it seems to pass power WAY to fast with the new software.  Does anyone else have this problem?

  My iPhone 6 installed 10.0.2 stops when it gets to 40% of autonomy.  In addition, it seems to pass power WAY to fast with the new software.  Does anyone else have this problem?

  Hello brooksm549,
  Thank you for using communities of Apple Support.

  I got your message which, since updating your iPhone 6 to iOS 10.0.2 your iPhone stops when it is 40% and the power to empty very quickly. I understand your concern with the iPhone turn off and drains the battery. I recommend you to review the use of the battery to see what app contributes more to the battery drain. The following article will provide you with steps on how to check the use of the battery:

  On the use of the battery on your iPhone, iPad and iPod touch

  When you know about the soft uses more battery, you can change your settings in order to optimize the battery life:

  Maximize the life of the battery and battery life

  Best regards.

• I had a problem with my iPad 2 Air when I changed my Apple ID password, the problem is, it shows me a Massage says ENTER the PASSWORD, and then said your PASSWORD will be used when the signature with the new device, but when I but the code it shows fail m

  This problem happened to me and it belongs to iCloud and I have used so important, please can someone help me?

  Hello. The access code on your iPad is the code four or six numbers you will need to enter to unlock the device. It has nothing to do with the verification of your Apple ID or two-step. Are you able to unlock your phone? If you are, then please describe the steps that lead to your problem. Since you have changed your Apple ID password, you will need to go to two settings > iCloud and settings > iTunes and app store and sign out of your Apple ID, then connect back with the new PW.

• Problem with the new update

  Any browser looks graphically unstable and content is empty with the new update, is it just me or is just the update which is unstable?

  Hello

  Try disabling graphics hardware acceleration. You will have to perhaps restart Firefox for it to take effect, so save any work first (e.g. you compose mail, documents online that you are editing, etc.).

  Then perform the following steps:

  1. Click the menu button

     

     then select Options Preferences on Mac or Linux, or Windows.

  2. In the window of Firefox Options (or preferences), click on the Advanced tab, and then select general.
  3. You will find in the list of parameters, the checkbox use hardware acceleration when available . Clear this check box.
  4. Now restart Firefox and see if the problems persist.

  In addition, please check the updates for your graphics driver by following the steps in the following knowledge base articles:

  • Troubleshoot extensions, themes, and issues of hardware acceleration to resolve common problems of Firefox
  • Update your graphics drivers to use hardware acceleration and WebGL

  This solve your problems? Please report to us!

  Thank you.

• Problems with the new Macbook pro 15' maxed out

  Here's a quick post about my experience so far with the new macbook pro. I just got a brand new fully maxed out in spec macbook pro 15 inch 1 to SSD 16 GB RAM AMD R9 370 m GPU (set to automatic switching is not always) and a 2.8 to 4 GHz i7. I turned on and set it up which was nice and took 2 minutes. Then experience decreased a little when I saw an EST 05:36 hours of battery life remaining to 94%. So I loaded 100% and it is still 60% of battery life announced and no program running that I literally just signed a brand new machine.

  Then I tried to use the migration wizard to import a backup of my iMac 5 k so I can do everything on this clone for my laptop. After having successfully connected (he told me if my password for time machine was incorrect or not) it froze and did nothing, continue did nothing.

  Then place had to call support, was a guy on the phone in 30 seconds and I unplug and restart the machine time, always that same question so I transferred to a guy with "more training". The new guy I could say knew a little more and knew that I knew how to set my password or if I walked in their properly for a bit but they all have been set for the same password just for this. I created a second admin account called "test" under his leadership, and when the migration assist froze on this account, he was surprised and proceeded to transfer me off.

  I preceded to restore fully the machine into thinking that my account setup is causing trouble with the migration assistant, and it turns out that the closure of that laptop it can only continue to 'download additional components', while that connected for 30 minutes so all last night was wasted, and now I guess he's got 5 left 12 hours to download original 'things '. Keep in mind that I can download 5 GB in one hour... After he wake up this morning and ending up where I left it last night :/ he says 84 hours go, now 72 and 51 and it is not updated even once in seconds, it took 20 minutes to 84 minutes to 51, it's literally a day 2 reset extravagance or what? Just to download it I can only imagine the actual plant until I can install my programs.

  The cost of the laptop was about $3600 but paid ~ $2900 after headphones were included and $250 off for delivery to students and other issues on the agenda of the process itself that is not my complaint, what happens, but sitting with a new camera and support useless just to ask me if I can use actually tomorrow at this price are unacceptable.

  I would like to continue using it for a while.

  You can try to reset the SMC http://support.apple.com/kb/ht3964

• Don t work under El Capitan and I don't get an update/upgrade? I've used until yesterday an old MacBook pro and Lion, everything was perfect with an opening. Now, with the new element (iMac) and El Capitan, I have problems.

  Don t work under El Capitan and I don't get an update/upgrade? I've used until yesterday an old MacBook pro and Lion, everything was perfect with an opening. Now, with the new element (iMac) and El Capitan, I have problems.

  It is not possible to update the version of Aperture is 3.4.5

  What can I do?

  You can only update if you have a version of the AppStore of Aperture - if your version of Aperture appears in the history of your purchases on the App Store. Update and then reinstalling.   See this tip of the user for more details:

  Update to Aperture 3.6 after the publication of Photos