Compatibility SFP
Hello
I currently have several Cisco C2960X-24TD-L. I would like to read, it is possible to connect two SFP GLC-SX-MMD and GLC-LH-SMD with a multimode cable.
When the switch is connected to the GLC-LH-SMD lights but the GLC-SX-MMD does not illuminate. He will issue an order?
Kind regards
I would savois it is possible to interconnect two SFP GLC-SX-MMD and GLC-LH-SMD with a multimode cable.
Is not possible. The two modules (and associated cables) must be of the same wavelength. It is GLC-SX-MMD-to-GLC-SX-MMD (with multi-mode cable) or GLC-LH-SMD-to-GLC-LH-SMD (with single-mode cable).
Tags: Cisco Network
Similar Questions
-
MGBLX1 Sw 2960 X compatibility
My question is if the FPS MGBLX1 is compatible whit a Cisco 2960 X thanks Sw.
Hello
The MGBLX1 is intended to be used with the Small Business of switches range. Research on the matrix compatibility SFP 2960 X will not support the MGBLX1.
If you try to connect a MGBLX1 on a switch of small business goes to a catalyst, the FPS on the catalyst must be a GLC-LH-SM. That the info came from the small business to the table of compatibility SFP Enterprise.
Hope that helps and thanks for using Cisco,
Christopher Ebert - Advanced Network Support Engineer
Cisco Small Business Support Center
* Please note the useful messages *.
-
I'm about to take my PC3524 a PC6248. Is the SFP transceiver in my 3524 compatible with the 6248? Or I have to get the new transceiver also?
Thank you
This transmitter/receiver is compatible with both switches and will work fine.
See you soon
-
PowerConnect 6248P 10 G SFP + compatibility
Hello
Is could someone please tell me if this device is compatible with 6248Ps after adding a module of 10 G uplink for the back?
Thanks in advance
Peter
Yes, this transceiver will work perfectly in your P. 6248
-
Compatibility of standart N3024F FPS
Hi, I want to buy a N3024F switch and I need to know if it is compatible with standard SFP or manufacturer DELL SFP only...
Thank you...
Hi, it is advisable to use SFP Dell brand to avoid compatibility problems. You can select the type of SFP based fiber race length.
-
Cisco WS-C3750X-12 s - S SFP modules
Dear team
I required 12 new sfp port switch I chose WS-C3750X-s-12s
for my requrement is here my question is...Is I need to add separate trancievers SFP for this switch or not?
Care technical I have not found that rock come alongwith 12 trancievers then how can I configure this procudt
Hello
The X Catalyst 3750 - 12s switch is a based FPS you don't need SFP transceivers. Take a look at table 6 to the Cisco Gigabit Ethernet transceiver Modules compatibility matrix for details on the supported transceivers and the OS release that they are taken care of.
Concerning
-
DWDM SFP modules - where to use?
Hi, we intend to interconnect two sites using DWDM. What type of SFP modules (color, color No 1310) should we use on our connection to the multiplexer/OADM switches? Does rely on the real device of MUX?
DWDM and OADM multiplexers filters have ports specific wavelength, which are connected to an optical transmitter/receiver of the same wavelength. Here is a link to the pluggable optical transceivers of Cisco DWDM
http://www.Cisco.com/en/us/products/ps6576/index.html
Cisco DWDM filters options linked below:
http://www.Cisco.com/en/us/prod/collateral/modules/ps5455/product_data_sheet0900aecd806a1c36.html
http://www.Cisco.com/en/us/products/HW/optical/ps1996/products_data_sheets_list.html
Optical TRANSCEIVER for hardware compatibility
http://www.Cisco.com/en/us/products/HW/modules/ps5455/products_device_support_tables_list.html
Let us know if you have any additional questions.
-
Are off brand SFP modules that ensure a Cisco compatibility worth anything?
Like you can get copper GigE GLC - T of SFP = 3750's made by other companies how eNet for example?
Disclaimer
The author of this announcement offers the information in this publication without compensation and with the understanding of the reader that there is no implicit or explicit adequacy or adaptation to any purpose. Information provided is for information purposes only and should not be interpreted as making the professional advice of any kind. Use information from this announcement is only at risk of the reader.
Any author will be responsible for any damage that it (including, without limitation, damages for loss of use, data or profits) arising out of the use or inability to use the information in the view even if author has been advised of the possibility of such damages.What do you really want? Ask yourself if it's a "good idea" to use brand X SFP in Cisco equipment? If so, it is to you. I believe that if you have problems with these SFP modules, Cisco will not support you unless you use their SPFS.
Then, if the brand X SFP work and they cost less, then it can be a "good idea." If you have problems, then it may not be a "good idea." Can't tell how the reduced cost (?) vs Cisco support is important to you. It's something you have to decide.
-
Hello
Can someone tell where I can download the Cisco 10 G SFP + with DOM data sheet? I could find one, but it does not include details of digital optical monitoring (DOM). Unlike in 100Base, care data SFP SFP 1000Base, it includes information on the DOM.
Help, please...
Thank you
Shawn
First link of Sunil will work better for most people without any partner in the URL. for example,.
The main 10GBASE SFP + form indicates these transceivers support digital optical followed in the main features section right at the top:
http://www.Cisco.com/en/us/prod/collateral/modules/ps5455/data_sheet_c78-455693.html
There are no more details, but I can testify that they have it and it works fine. I used it several times.
-
Can I change the speed on a GB SFP?
We have an ASR1002 edge router I need to connect a 100 LH SM Fiber (1310). I have a GLC-LH-SM and a SFP SFP-GE-L. I need to set the speed to the ASR for the interface of the FPS to 100/full. The IOS does not "speed" controls at the interface level. Can I set the speed to 100 for one of them and, if so, how?
Cannot change the speed for SFP module.
However, for the 100 M SFP Transceiver compatibility Document (link below), the ASR1002 supports the module of GLC-GE-100FX of 100 MB interconnects (split into a compatible slot in GE).
Good luck!
-
Intel PCI X 520 10 WHAT GIGABIT SFP + not loaded in ESXI 6.0
Hi all
I'm under ESXI 6.0 and installed the latest drivers from intel PCI X 520 10 Giga cards with branch above DELL SFP modules I searched the forum for similar issues and found that it was perhaps the module are not supported so here my info of the commands below
I have also the same out put regarding this thread
less /var/log/vmkernel.log | grep-i "FPS".
(2015 09-29 T 08: 53:22.296Z cpu2:33341) < 3 > IGB 0000:0: 00.0: failed to load because a type of module SFP + and QSFP not supported has been detected.
(2015 09-29 T 08: 53:22.316Z cpu2:33341) < 3 > IGB 0000: 0a: 00.1: failed to load because a type of module SFP + and QSFP not supported has been detected.
also this command
lspci | grep vmnic *.
0000:03:00.0 network controller: Broadcom Corporation NetXtreme BCM5719 [vmnic0] Gigabit Ethernet
0000:03:00.1 network controller: Broadcom Corporation NetXtreme BCM5719 [vmnic1] Gigabit Ethernet
0000:03:00.2 network controller: Broadcom Corporation NetXtreme BCM5719 [vmnic2] Gigabit Ethernet
0000:03:00.3 network controller: Broadcom Corporation NetXtreme BCM5719 [vmnic3] Gigabit Ethernet
0000:07:00.0 network controller: Broadcom Corporation NetXtreme BCM5720 [vmnic4] Gigabit Ethernet
0000:07:00.1 network controller: Broadcom Corporation NetXtreme BCM5720 [vmnic5] Gigabit Ethernet
0000: 0a: 00.0 Network controller: Intel Corporation 82599 10 Gigabit double Port card WIRELESS [vmnic6]
0000: 0a: 00.1 Network controller: Intel Corporation 82599 10 Gigabit double Port card WIRELESS [vmnic7]
the problem is the vmnic6 and 7 is not displayed on the list vmnic
ethtool-i vmnic6
Cannot control himself fd: no such file or directory
I also checked this thread How can I activate my to use 10GbE ports (need to create new VMKernel) are not in the list of adapters.
VMware-l
VMware ESXi 6.0.0 GA
list of network adapter for the network esxcli
Name PCI Device Driver status Admin link status speed Duplex MAC address MTU Description
------ ------------ ------ ------------ ----------- ----- ------ ----------------- ---- -------------------------------------------------------
vmnic0 0000:03:00.0 tg3 Up Up 1000 Full 40:a8:f0:29:6 has: 20 1500 Gigabit Ethernet Broadcom Corporation NetXtreme BCM5719
vmnic1 0000:03:00.1 tg3 Up Up 1000 Full 40:a8:f0:29:6 has: 21 1500 Gigabit Ethernet Broadcom Corporation NetXtreme BCM5719
vmnic2 0000:03:00.2 tg3 Up Up 1000 Full 40:a8:f0:29:6 has: 22 1500 Gigabit Ethernet Broadcom Corporation NetXtreme BCM5719
vmnic3 0000:03:00.3 tg3 Up Up 1000 Full 40:a8:f0:29:6 has: 23 1500 Gigabit Ethernet Broadcom Corporation NetXtreme BCM5719
vmnic4 0000:07:00.0 tg3 Up Down 0 40:a8:f0:36:15:0e half 1500 Gigabit Ethernet Broadcom Corporation NetXtreme BCM5720
vmnic5 0000:07:00.1 tg3 Up Down 0 40:a8:f0:36:15:0f half 1500 Gigabit Ethernet Broadcom Corporation NetXtreme BCM5720
also check the bios for a similar option
BIOS "Default memory mapped IO above 4 GB option in the BIOS.".
I have not found this option, I HP Proliant DL380 Gen8.
esxcfg-NICS - l
Name PCI Driver link speed Duplex MAC address MTU Description
vmnic0 0000:03:00.0 tg3 up to 1000Mbps Full 40:a8:f0:29:6 has: 20 1500 Gigabit Ethernet Broadcom Corporation NetXtreme BCM5719
vmnic1 0000:03:00.1 tg3 up to 1000Mbps Full 40:a8:f0:29:6 has: 21 1500 Gigabit Ethernet Broadcom Corporation NetXtreme BCM5719
vmnic2 0000:03:00.2 tg3 up to 1000Mbps Full 40:a8:f0:29:6 has: 22 1500 Gigabit Ethernet Broadcom Corporation NetXtreme BCM5719
vmnic3 0000:03:00.3 tg3 up to 1000Mbps Full 40:a8:f0:29:6 has: 23 1500 Gigabit Ethernet Broadcom Corporation NetXtreme BCM5719
vmnic4 0000:07:00.0 tg3 0Mbps Down a half 40:a8:f0:36:15:0e 1500 Gigabit Ethernet Broadcom Corporation NetXtreme BCM5720
vmnic5 0000:07:00.1 tg3 0Mbps Down a half 40:a8:f0:36:15:0f 1500 Gigabit Ethernet Broadcom Corporation NetXtreme BCM5720
output-l esxcfg-module
See attached fileand one thing is in the bios I have unknown pci
See attached file
the question is do I have to replace the sfp only or the entire map that I bought recently or is there a fix for it in the latest version of ESXI?
Thank you
I can confirm compatibility.
also a comment is to use the intel SFP modules with Pci cards intel. who works on esxi servers
-
Before I dive and upgrade to Sierra, I'm looking for a reliable source check the compatibility of the applications, I currently rely on. Many are a bit dated. Any suggestions?
Main applications:
Microsoft Office for Mac 2011 v 14.6.8
Quicken for Mac 2007 v 16.2.4
Photoshop CS5 x 64 new v12.0
Roxio Toast 10 Titanium v 10.0
Apple Pages, Numbers and Keynote ' 09
Running OS X Lion mountain.
Click here.
(145086)
-
I have to stay with OS10.7.5 due to software compatibility, but is it possible to update Safari to latest version during your stay on OS10.7.5. How this is done. Thank you very much.
It is not possible to update Safari past 6.1.6 on Lion.
(144969)
-
How to: Crush 3/iMac 5 k (compatibility mode)
Hello friends,
I see quite a few new features on the market with Thunderbolt 3. According to the FAQ of TB3 Intel, TB1 and TB2 was designed with future upgrades in mind. This means that you can connect, once a solution is available, on a host of TB2 TB3 system using compatibility mode. It will only work to 20Gbps TB2, but work remains. The same is true of peripheral TB2 TB3 host computer (will work but at slower speed)
This would be similar to the connection of a USB 3 device on a USB 2 or 1 USB host but only get speeds over slow or vice versa.
The question I have is that if someone came out with these fittings/adapters? What I've seen online seems to go using a device of TB2 and TB3 host and each of these adapters is Windows only. I have spent too many hours searching so I'm curious to know if someone has yet to fall on an adapter or converter that connect DisplayPort TB2 host and have the device USB-C/TB3 (USB - C not only) in compatibility mode.
The reason? Peripheral TB3 are already less expensive than TB2 devices. I don't know who will get the most expensive. I don't care 40Gbps if he gives me a simple way to add multiple devices USB 3.0, exhibitions and maybe the eSata device. I know there are hubs, but I would prefer something that is the test of the future TB3 would be cheaper and future proof for NeXTGen computers.
(Sorry for the TL; DR but it is always a person who does not read or "assume" it is a noob question and gives an answer "Captain Obvious". Don't BE this guy here...)
Sincere greetings,
Jorge Uptown
JLopez. Chicago wrote:
The question I have is that if someone came out with these fittings/adapters?
-
DIGITAL CAMERA RAW COMPATIBILITY UPDATE 6.21
***? How many times I have to do? I'm FED UP! I don't care ABOUT RAW! Update your program... I have
NEVER USE! NOT my computer!
You're not talking Apple here. It is a moderated forum for Apple to discuss features and troubleshooting. Apple-> system-> software update Preferences menu contains options to disable automatic downloads, although the Mac App Store update itself for Snow Leopard activates the automatic notifications of updates. While a nuisance, you have just to tell more later, only choose to update once you have read the documentation to verify that its good operation with what you have. Always back up your data before allowing updates.
For direct feedback to Apple, who may have only one impact of future operating systems, http://www.apple.com/feedback
If you find that a specific update has compatibility issues, we invite you to sign up for a free developer online account on http://developer.apple.com and submit a bug report to http://bugreporter.apple.com where you can know at least that if it's something reported before. But this will not use or disclose this information here because of a confidentiality agreement.
Maybe you are looking for
-
Write table 1 d to drop at specific sampling frequency
Hey everybody! I'm back to ask what probably is another simple question. I have 6 cells of custom load that are read in a sub - VI. The Subvi is inside a loop for, which is inside a structure of the case, which is inside a while loop. Here's what it
-
I had the same problem with Windows Vista
-
inabilty sudden to connect to any network
My second laptop to vista SP2 will be no longer connect to the internet via any network - have tried wireless and LAN, secured and unsecured. It will connect to the network itself, but nothing else - cannot ping other IP address on the network, DNS s
-
HelloI've looked everywhere in my phone call settings, but I can't find anything about my problem.When I talk with someone if I get another call and I pick up the phone to ear to look who calls phone automatically answer the second person and the fir
-
I need to edit a video that I downloaded from my camera. He got a .mov for file extension. Doesn't work in all Microsoft products.