Computer crashes frequently with errors of "Blue Screen of Death" as shown below. These occur usually (but not always) after that the PC has been in sleep/wake.

Here is the blue screen errors

IRQL_NOT_LESS_OR_EQUAL

MEMORY_MANAGEMENT

PFN_LIST_CORRUPT

-------------------------
Bought PC in Nov 2008
Q6600
Vista SP2
ATI 4850 graphics card
4 GB of RAM
500 GB HD

Hello

Probably either a (most likely) driver error or faulty memory. First run the internal memory diagnosis (just "type diagnosis memory" in the start/search to start line). If it passes, then we will have to analyze the dump file is created.

If the error messages are compatible - even verbiage and error code, it is more likely to be a driver problem. If they are constantly changing, so the problem is more likely to be a faulty hardware. Start by memory, then maybe a hard drive diagnostic. If they pass, then the next step is exchanging materials well known from the power supply. Good luck, Rick Rogers, aka "Crazy" - Microsoft MVP http://mvp.support.microsoft.com Windows help - www.rickrogers.org

Tags: Windows

Similar Questions

  • I'm having a problem with Windows7 Home Premium and WWII CFS joystick operation. I get a message saying that the controller has been changed. Microsoft offers a patch?

    I have problems with Windows7 Home Premium and WWII CFS joystick operation.  I get a message from gibberish, saying that the controller has been changed.  I tried to replace the file with a version of Windows XP .cfg and also tried to re-write the .cfg file.  Apparently, this version of Windows will not allow a file to be saved with an extension ".cfg", so it does not work either.  Any suggestion would be appreciated.

    Thank you

    Hi Bob,

    You can consult the following links of wire and check if it helps.

    Joystick does not work with the Europe of WWII Combat Flight Simulator series. Help?

    With the help of WW2 Europe Combat Flight Simulator series with Windows 7 Home Premium

    Note: The above links contain third party links. Using third-party software, including hardware drivers can cause serious problems that may prevent your computer from starting properly. Microsoft cannot guarantee that problems resulting from the use of third-party software can be solved. Software using third party is at your own risk.

  • I have the first Pro 2015 but when I try to open a project that has been registered with the Premier Pro 2015 on another machine I get an error message that says that the project has been saved with the latest version.  Help!

    I have the first Pro 2015 but when I try to open a project that has been registered with the Premier Pro 2015 on another machine I get an error message that says that the project has been saved with the latest version.  Help!

    It seems that your version is not the latest.

    Check help / about... what version it reads.

    It should be 2015. (9.2.0 build 41)

    Otherwise, please update your version via app updates... or cloud in respect of aid.

  • After a new installation of OSX Lion, I want to reinstall my firefox sync preferences. I saved my key before clening the computer, but not firefox indicates that the key is incorrect. Any ideas would be most appreciated!

    After a new installation of OSX Lion, I want to reinstall my firefox sync preferences. I saved my key before clening the computer, but not firefox indicates that the key is incorrect. Any ideas would be most appreciated!

    Try typing the key to recovery without 5 dashes.

  • Epson Aculaser C 1100 printer does not print after that the text of the error 'install C Tnr basket' black and printer doenst photography black and white or grayscale pages

    Epson Aculaser C 1100 printer does not print after that the text of the error 'install C Tnr basket' black and printer doenst photography black and white or grayscale pages

    the printer is not the shades of grey even print cartridge is not yet empty

    y at - it software for hauler color printing?

    Thanks for your comments

    Hello Nilsvolkel,

    Thanks for the reply.

    I'm sorry for the late reply.

    I appreciate your patience and time.

    Do not require any special software.

    However, you can use the steps in the following articles and check.
    Reference:
    http://eSupport.Epson-Europe.com/ViewArticle.aspx?LNG=fi-fi&kbid=328037&data=FCFfEfoyEiGLYDIUqzWyE0QE3127X87y&CL=1

    http://Windows.Microsoft.com/en-us/Windows/choosing-print-options#1TC=Windows-7

    Please keep us informed.

    Thank you

  • I'm trying to scan a doc and the message is 'not found computer. Ensure that the HPsoftware has been installed on the computer.

    I'm trying to scan a doc and the message is 'not found computer. Ensure that the HPsoftware has been installed on the computer. My computer print very well so I do not know why it does not scan.

    Hello

    Thanks for the information. Two things to try. First of all, try to align your print cartridges using the controls on the printer display panel. As part of this process, the printer will print on a sheet of alignment that you place on the printer and scan in the printer. See if it works successfully. If not, see the following page: http://h10025.www1.hp.com/ewfrf/wc/document?docname=c02451000&cc=us&dlc=en&lc=en&jumpid=reg_r1002_usen_c-001_title_r0011 .

    The second thing to try is the print and Scan Doctor Utility, download here: http://h10025.www1.hp.com/ewfrf/wc/softwareDownloadIndex?softwareitem=mp-114642-1&cc=us&dlc=en&lc=en&os=4063&product=5061082&sw_lang=. Its a standalone process and requires no explanation.

    Let me know if one of them fixes the problem.

    Kind regards

    BearPup

  • Silverlight has been installed on my dell with media player and after that the tuner has stoped running silverlight would have something to do with it? I get a low rate and no signal tuner.

    Silverlight has been installed on my dell with media player and after that the tuner has stoped running silverlight would have something to do with it? I get a low rate and no signal tuner.

    Hello

    Thanks for the quick response.

    What web browser do you use to access the links in my previous post?

    If you use Internet Explorer, I suggest to optimize Internet Explorer settings and check if it works.

     

     

     

    How to optimize Internet Explorer

    http://support.Microsoft.com/kb/936213/ro

     

    Warning: Please note that the reset Internet Explorer (IE) resets all of the settings defined by the user, including those established by the installed extensions, toolbars and other add-ons for IE by default. This includes all the security, privacy and settings area. Also this will erase browsing history, delete all temporary Internet, cookies, form data files and especially all the passwords.

     

    If the problem persists, you can reinstall the drivers for the Tuner card and check with the question.

    It will be useful. For any other corresponding Windows help, do not hesitate to contact us and we will be happy to help you.

  • I'm trying to upgrade a site from Muse and it keeps telling me that the site has been created with a different version of Muse. I have updated Muse and still can not access the site to make changes.

    I'm trying to upgrade a site from Muse and it keeps telling me that the site has been created with a different version of Muse. I have updated Muse and still can not access the site to make changes.

    Hi rgarden95,

    Can you please confirm the exact version of Muse, you open the file with?

    To check the version of Muse, please click Help-> on Adobe Muse CC.

    Kind regards

    Akshay

  • Help with error on blue screen under Vista 32 bit

    Had this message pop up several times. Any ideas?
    Thank you!
    Signature of the problem:
    Problem event name: BlueScreen
    OS version: 6.0.6000.2.0.0.768.3
    Locale ID: 1033
    More information about the problem:
    BCCode: fe
    BCP1: 00000008
    BCP2: 00000006
    BCP3: 00000001
    BCP4: 867B 9000
    OS version: 6_0_6000
    Service Pack: 0_0
    Product: 768_1
    Files helping to describe the problem:
    C:\Windows\Minidump\Mini122811-01.dmp
    C:\Users\xxx\AppData\Local\Temp\WER-37955-0.SysData.XML
    C:\Users\xxx\AppData\Local\Temp\WERB24D.tmp.version.txt
    Read our privacy statement:
    http://go.Microsoft.com/fwlink/?LinkId=50163&clcid=0x0409

    Hello

    Do not forget to check with the manufacturer of system support (or motherboard for custom systems manufacturer)
    and their forums (if any) for known issues.

    Check these KB Articles that "pourraient" apply.

    Stop 0xFE peripheral sleep or Hibernate with USB streaming output
    http://support.Microsoft.com/kb/974303

    "Stop 0x9F" error or "Stop 0xFE" on a Windows 7 or Windows Vista-based computer that
    use some USB AMD EHCI host controllers
    http://support.Microsoft.com/kb/982091

    ==================================================================

    Check this thread for more information using BlueScreenView, MyEventViewer and other methods
    to troubleshoot the BlueScreens - top 3 responses (+ 1 other).

    http://answers.Microsoft.com/en-us/Windows/Forum/windows_vista-system/blue-screen-plug-and-play-detected-an-error-most/3deab2fa-4000-4136-8c78-a3d22b1db009

    We can analyze the minidumps if make you it available to the SkyDrive or another file
    sharing sites (such as MediaFire). If you have problems to download the copy of minidumps
    for the office or in the Documents folder and download them from there.

    ZIP or download the content of the C:\Windows\minidump

    Use SkyDrive download collected files and after shot/screenshot.
    http://social.technet.Microsoft.com/forums/en-us/w7itproui/thread/4fc10639-02dB-4665-993a-08d865088d65

    =============================

    Although the control of bug 0xFE: BUGCODE_USB_DRIVER indicates generally material it could easily
    be a connected USB device and not a system USB device. And you can never really exclude drivers.

    BCCode: FE 0x000000FE<-- read="" this="">
    http://www.faultwire.com/solutions-fatal_error/BUGCODE-USB-driver-0x000000FE-* 1251.html? = date order

    --------------------------------------------------------------------------------------

    A possible cause can be updated to Windows, including pilots. Even the drivers are generally not considered as the
    USB-related, such as video/display, network (NIC & WiFI) and others, may be the cause.

    Especially Norton, Kaspersky, McAfee, SpyBot, Adaware and others may cause or have a role
    in this issue. Try to uninstall it to see if that helps. Use the removal of their creator tools and/or
    Special instructions. (Antivirus/antispyware/security programs)

    ----------------------

    Remove all THE USB devices on the computer. Don't forget to search the drivers updated for all USB
    devices.

    References to Vista also apply to Windows 7.

    Try these to erase corruption and missing/damaged file system repair or replacement.

    Run DiskCleanup - start - all programs - Accessories - System Tools - Disk Cleanup

    Start - type in the search box - find command top - RIGHT CLICK – RUN AS ADMIN

    sfc/scannow

    How to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe) program
    generates in Windows Vista cbs.log
    http://support.Microsoft.com/kb/928228

    Then, run checkdisk - schedule it to run at next boot, then apply OK your way out, then restart.

    How to run the check disk at startup in Vista
    http://www.Vistax64.com/tutorials/67612-check-disk-Chkdsk.html

    -----------------------------------------------

    Then lets refresh the USB stack

    Control the click Control Panel - Device Manager - no matter where in the box of white/white - then the VIEW - see the
    Devices disabled - look around (with the exception of USB controllers) for all hidden devices / people with disabilities
    (can have zero or more than one) and top - right click UNINSTALL.

    Control Panel right CLICK on EVERYTHING - Serial USB controllers - device configuration-manager and
    UNINSTALL all but the category itself - REBOOT - it refreshes the driver and battery USB

    This KB shows XP how to and methods of Vista and Windows 7 are the same
    http://support.Microsoft.com/kb/310575

    This is a utility to help you, but do 1 above.

    USBDeview is a small utility that lists all USB devices currently connected to your computer.
    as well as all USB devices that you previously used. Run Options and tick three 1
    are there choices to see if any.

    http://www.NirSoft.NET/utils/usb_devices_view.html

    You must remove all instances of the devices and restart.

    ----------------------------------------------

    If necessary try these two:

    Tips for solving problems of USB devices - and a Mr Fixit
    http://windowshelp.Microsoft.com/Windows/en-us/help/c39bd203-f729-47a4-8351-83291e13c8a81033.mspx#EGB

    Hardware devices not detected or not working - Mr. Fixit
    http://support.Microsoft.com/GP/hardware_device_problems

    =======================================

    After the above, attach a USB device at a time to see if any cause the issue.

    I hope this helps.

    Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle=""><- mark="" twain="" said="" it="">

  • Several errors in 'Blue screen of death' and all default programs are broken? (Windows 7)

    Hello, I recently built a computer. It is about 2 weeks old and runs Windows 7 Ultimate.

    When I got it, it worked fine, but suddenly any program which was not preinstalled / microsoft basic started to plant. So far, the only program of Microsoft crashing is Internet Explorer, which leads me to believe that I may have some kind of internet problem.

    What happens usually is I'll open a program, and it will crash, sometimes instantly and sometimes after an hour. I checked my diary of events, and it shows nothing after a crash.

    Sometimes even though I have a window open, I get the blue screen, with 4 Messages up to now:

    -System Service Exception

    -Memory management

    -Failure of Page in a non paged area

    -Driver IRQL not less or equal

    I saw each other once, the exception of the memory management, which I got 3 times.

    I have so far to try to resolve this problem:
    Updated all drivers

    System restored

    Uninstalled all unnecessary programs.

    Other ideas are appreciated, I would prefer no 'generic' as ideas, "have you tried to update -?", at this time I need a difficult solution.

    Graysun

    If memtest failed it's memory or the mobo slot.  Delete a stick (if you can) and repeat the test individually.

    You will need the bad ram RAM

  • I have no idea where my installation for my operating system discs are... but I need to reinstall a dll that I had my computer off and when he returned to the top needed to fdisk... and when he fixed things that the dll has been corrupted.

    where can I download the dll for windows vista ultimate 64 msxml4.dll?

    I tried to get my installation discs and I can't find them. I tried to contact alienware and they said to contact microsoft.
    I tried to use the features of support, but when it asked me to put in my ID of product of your Web page will not accept for any reason any.

    now what should I do?

    can you send me this dll? my email is * address email is removed from the privacy *.
    I'm fucked without my darn install disks.

    You do not qualify for FREE Microsoft Support as your Vista operating system is preinstalled, with the exception of problems with Vista SP2. () Information about this is provided below.)

    All the support your Vista is the manufacturer of your computer.
    https://support.Microsoft.com/OAS/default.aspx?PRID=13014&Gprid=582034&St=1

    Free unlimited installation and compatibility support is available for Windows Vista, but only for Service Pack 2 (SP2). This support for SP2 is valid until February 26, 2010.

    Microsoft free support for Vista SP2 at the link above.

    ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

    How to get Vista recovery Media and/or to use the Vista recovery Partition on your computer.

    There is no Vista free download legal available.

    Contact your computer manufacturer and ask them to send a recovery disk/s Vista set.

    Normally, they do this for a cost of $ small.

    ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

    In addition, ask them if you have a recovery Partition on your computer/laptop to restore it to factory settings.

    See if a manual provided with the computer or go to the manufacturer's website, email or you can call for information on how to make a recovery.

    Normally, you have to press F10 or F11 at startup to start the recovery process...

    Another way I've seen on some models is press F8 and go to a list of startup options, and launch a recovery of standards of plant with it, by selecting the repair option.

    ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

    You can also make recovery disk/s for the recovery Partition in case of a system Crash or hard drive failure.

    They will tell you how to do this.

    Every computer manufacturer has their way of doing recovery disk/s.

    ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

    Or borrow a good Microsoft Vista DVD (not Dell, HP, etc).
    A good Vista DVD contains all versions of Vista.
    The product key determines which version of Vista is installed.

    There are 2 disks of Vista: one for 32-bit operating system, and one for 64-bit operating system.

    If install a cleaning is required with a good DVD of Vista (not HP, Dell recovery disks):

    Go to your Bios/Setup, or the Boot Menu at startup and change the Boot order to make the DVD/CD drive 1st in the boot order, then reboot with the disk in the drive.

    At the startup/power on you should see at the bottom of the screen either F2 or DELETE, go to Setup/Bios or F12 for the Boot Menu

    http://support.Microsoft.com/default.aspx/KB/918884

    MS advice on the conduct of clean install.

    http://www.theeldergeekvista.com/vista_clean_installation.htm

    A tutorial on the use of a clean install

    http://www.winsupersite.com/showcase/winvista_install_03.asp

    Super Guide Windows Vista Installation

    After installation > go to the website of the manufacturer of your computer/notebook > drivers and downloads Section > key in your model number > get latest Vista drivers for it > download/install them.

    Save all data, because it will be lost during a clean installation.

    See you soon.

    Mick Murphy - Microsoft partner

  • 0x800704D3 error: the backup was not completely successful. The application has been abandoned, as he tried to take backup

    Original tile: appeared at the end of backup when the error message appeared. "The reverse was not entirely successful. The request was abandoned. (0x800704D3)

    Recently I had a problem with the combo of virus/malware.  Antivirus 2010, was then brought by an another 'guru' to download StopZilla.com who started the Delete files accompanying the computor.  I have kept and can't get rid of the problem, so decided to back up files, and then put in recovery disks.  Appeared at the end of backup files with the ninth disk, when the error message above has occurred. Is not something else.  Someone said elsewhere "make sure that the AC adapter is on"... what?  THA is the problem?

    Seen also it is suggested to get an external hardware, but what about hang the laptop to existing pc?  Would you do that?  What wiring do I need?

    Hi beltwaytraveler,

    1. you have any third-party backup program installed?

    2 have you tried to use a different backup disk?

    Method 1:

    You can temporarily uninstall third-party anti-virus on your computer protection software and then check if the problem occurs.

    Note: Be sure to install the security software on the computer after you fix the problem.

    Method 2:

    You can also try to uninstall any third-party backup program installed on the computer and try the backup.

    Method 3:

    You try to run the following command and check if all third-party services are running other Microsoft services.

    a. Click Start, click programs, accessories principally made, right click Guest and then click Run as administrator.

    If you are prompted for an administrator password or a confirmation, type the password, or click on allow.

    b. type the following command and press ENTER:

    vssadmin list writers

    c. check the VSS writers listed.

    If you see any third-party service other than Microsoft services running, and then let us know about it.

    Hope this information is useful.

    Jeremy K
    Microsoft Answers Support Engineer
    Visit our Microsoft answers feedback Forum and let us know what you think.

    If this post can help solve your problem, please click the 'Mark as answer' or 'Useful' at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

  • None of my apps work after that my laptop has been infected with the virus Vista Internet Security 2010,

    Hi all
    I need help to get my computer back to normal.

    My laptop has been infected with the virus Vista Internet Security 2010, but I removed it, NOW none of my apps (Yahoo Messenger, trash, other folders, SYSTEM, all file icons restore,) work, I managed to get rid of the virus visa, but still none of the programs work. When I try to open any program, it displays an error message "this file has no program associated with it for performing this action. Create an association in the set associations Control Panel. " I did all the steps, but still nothing works now all my files are open with the same file. I try to download a program to fix this problem, but I'm not able to run cause keep giving me the same error and cannot download anything. Is it possible to recover my computer as usual. Any help much appreciated.
    Help, please.
    Oh also all the icons on my destop are replaced by the same feacture of icon, but the name of the icons are staying same.if it shows adobe icon and all icons are adobe, when I open it with ie, then everything will change IE also. even if the opening programme has also changed to the same icon as dekstop one. now all my things are open with yahoo messenger:(c'est fou:()

    Try restarting your PC and press the F8 key repeatedly and then start in safe mode with networking and download and comprehensive performance analysis with:

    http://www.Microsoft.com/security/scanner/en-us/default.aspx

    If this does not work, try to run Windows Defender version offline beta:

    http://Windows.Microsoft.com/en-us/Windows/what-is-Windows-Defender-offline

    You can take a look at:

    http://cyberdefend.WordPress.com/2012/01/07/boot-Windows-for-scan/

    If the problem has not resolved, then contact Support for Microsoft Security:

    https://consumersecuritysupport.Microsoft.com/default.aspx?ProductKey=pcsafetymalware&task=Diagnostics&mkt=en-us&St=1&wfxredirect=1

  • On NEW laptop keyboard does not work after that the screen keyboard has been activated and then deactivated.

    Look at my friend got a new laptop and went through the whole upward. the on-screen keyboard has been activated which invalidates the real keyboard when the on-screen keyboard has been disabled the real keyboard has NO return. If this is a bug... Fix it. This is not a driver issue, it is not a user error. Stop giving people answers, trying to pretend like it's not not the OS when most people already know that it is.

    I'm sorry, but I didn't not new meant only one day.  And when I got my new laptop, one of the first things I did was to create a point of files, even a day later I had a restore to use - point and that was possible here as well.  I'm sorry it wasn't the case.

    If the system restore option is not available, do a startup repair, boot from the disk Installation of Windows Vista genuine (or one that you can borrow from someone) or a recovery disc.  Here is the procedure: http://www.bleepingcomputer.com/tutorials/tutorial148.html.  You may need to change the BIOS to do first the CD drive in the boot sequence to boot from the CD.  To do this, hold the screen that tells you the key F to push to enter the menu start or start of installation.  Push it quickly. Make the changes, save your work and exit.  Put the CD in the drive and reboot.  When you are prompted, press any key to boot from the CD.

    If you do not have a floppy disk, you can make a bootable recovery disk by using http://neosmart.net/blog/2008/windows-vista-recovery-disc-download/ with burning software like: http://www.snapfiles.com/get/active-isoburner.html and, of course, a blank CD.

    If this does not work, you can try to go into the BIOS during the startup (the key appropriate to push appear on the screen to enter the boot menu or boot installation - try them both in turn if both appear. It is possible that the BIOS contains an option to disable the keyboard (which may have been activated by the keyboard on the screen but not changed when disable you the on-screen keyboard) and you may need to re-enable manually.  There is a slight possibility, but it is an option to try.

    Another option to try is to set up a new user account that has never used the keyboard on the screen and see if the regular keyboard works when you connect to this account.  If so, you can simply treat the original as a corrupt account account and use the following procedures to complete the transfer.  To fix this use http://windows.microsoft.com/en-AU/windows-vista/Fix-a-corrupted-user-profile.

    I hope that one of these aid procedures.  I'm sorry if they seem to 'generic', but we do not really know what is the problem - especially since the system is new.  We try and identify the cause and fix the problem at the same time using the procedures available to us.  I suspect there's a registry tweak will correct this problem, but I went through the whole registry, and although I found several referencers keyboard, I could find no which seemed to control or not activate the main laptop keyboard (though it has been in one of the entries that has been encoded in binary that I couldn't read).  It's possible someone who knows more about the registry will respond to this issue with a proposal to amend (or perhaps another solution).

    I hope that one of the solutions I proposed works.  Please post back in all cases we will know whether or not to continue searching for an answer.

    Good luck!

    Lorien - MCSA/MCSE/network + / has + - if this post solves your problem, please click the 'Mark as answer' or 'Useful' button at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

  • When I connect to Windows 7 after that my laptop has been asleep, the Welcome screen will have 10 minutes to go beyond.

    When I connect to Windows 7 after my laptop has been asleep, the Welcome screen will block for always (10 + minutes). It does not every time, but maybe once all 5 or 6 times and it's happened lately. I can just shut the computer off and the newspaper with no problem after starting it upward, but I'm afraid, there may come a time where it does not work.

    I had this problem since I got my computer 2 months ago so I don't think it's related to what I have installed. Has anyone else encountered this problem and has found a way to fix it? Is this a common bug in all of Windows 7?

    original title: Windows 7 stuck on the Welcome screen

    Hello

    Safe mode - repeatedly, press F8 as you bootup. Another method is to start - type in
    Search-> find MSCONFIG in top box - just right-click on it - RUN AS Admin Startup tab
    -check the Safe Boot (network) APPLY / OK. Don't forget to change it if necessary.

    Try a system restore before what happened: (you can run system restore
    in the Windows as well however it sometimes works better in safe mode-
    repeatedly press F8 as you start.)

    How to do a system restore in Windows 7
    http://www.SevenForums.com/tutorials/700-system-restore.html

    ==========================================

    If it is mounted on the homescreen?

    Follow these steps to remove corruption and missing/damaged file system repair or replacement.

    Run DiskCleanup - start - all programs - Accessories - System Tools - Disk Cleanup

    Start - type in the search box - find command top - RIGHT CLICK – RUN AS ADMIN

    sfc/scannow

    How to fix the system files of Windows 7 with the System File Checker
    http://www.SevenForums.com/tutorials/1538-SFC-SCANNOW-Command-System-File-Checker.html

    Then run checkdisk (chkdsk).

    How to run check disk in Windows 7
    http://www.SevenForums.com/tutorials/433-disk-check.html


    ======================================

    You can try some of them in Mode safe - tap F8 repeatedly that you start.

    If you do not have a Windows 7 disc, you can borrow a friends because they are not a copy
    protected. The manufacturer of your system will also sell the physical DVD cheap since you already
    Clean Windows. You can also do an ERD on another computer.

    Try the Startup Repair - (if at anytime, benefit you from some, but not full access coming to Windows
    return and then try to startup repair.)

    How to start on the System Recovery Options in Windows 7
    http://www.SevenForums.com/tutorials/668-system-recovery-options.html

    What are the system recovery options in Windows 7?
    http://Windows.Microsoft.com/en-us/Windows7/what-are-the-system-recovery-options-in-Windows-7

    Try the disk Options recovery or Windows 7 startup repair.

    How to run a startup repair in Windows 7
    http://www.SevenForums.com/tutorials/681-startup-repair.html

    Also from the command PROMPT on the Console (if possible) recovery or a Windows 7 disc

    Start - type in the search box - find command top - RIGHT CLICK – RUN AS ADMIN

    sfc/scannow

    How to fix the system files of Windows 7 with the System File Checker
    http://www.SevenForums.com/tutorials/1538-SFC-SCANNOW-Command-System-File-Checker.html

    Then run checkdisk (chkdsk).

    How to run check disk in Windows 7
    http://www.SevenForums.com/tutorials/433-disk-check.html

    Retry After Chkdsk startup repair.

    If after those you can try the system restore to fashion without failure or the valuation or Windows 7
    disc.

    How to do a system restore in Windows 7
    http://www.SevenForums.com/tutorials/700-system-restore.html

    --------------------------------------------------------------------

    If you need to repair disks - these help repair Windows not re-install.

    How to create a Windows 7 system repair disc
    http://www.SevenForums.com/tutorials/2083-system-repair-disc-create.html

    ======================================

    If necessary:

    What to do if Windows does not start correctly
    http://Windows.Microsoft.com/en-us/Windows-Vista/what-to-do-if-Windows-wont-start-correctly

    How to start on the System Recovery Options in Windows 7
    http://www.SevenForums.com/tutorials/668-system-recovery-options.html

    What are the system recovery options in Windows 7?
    http://Windows.Microsoft.com/en-us/Windows7/what-are-the-system-recovery-options-in-Windows-7

    How to do a repair installation to repair Windows 7
    http://www.SevenForums.com/tutorials/3413-repair-install.html

    I hope this helps.

    Rob Brown - MS MVP - Windows Desktop Experience: Bike - Mark Twain said it right.

Maybe you are looking for

  • Delete on their own messages

    I have my e-mail service set to "keep forever", but today when I went to my messages, they were all gone. My contacts had gone to. I have not called my phone to do it, then, how can I get this canceled action?

  • Upgrade processor satellite Pro 4320

    Hello I need a little help, I'm looking for information on the upgrade of my pentium III 600 mhz for a slightly faster. I read that it is possible to switch to 700 mhz, but I'm looking for someone who knows what type of CPU max I can use in the machi

  • HP pavilion a622x: what is the top speed of ram I can spend on a HP pavilion a6228x?

    What would be the best way to move to 4 GB of ram currently 2 GB installed many messages from memory.

  • Adding a serial port to Tiny M73

    I am trying to understand the number of the serial port in option on the M73 (10AY001YUS). Can someone ponit me in the right direction? I found other posts here with psrt numbers, but I can't find out how to confirm they work with specific machines I

  • PC XP very slow opening files on network 2003-2008 since 7 days ago

    Since Wednesday last (06/29/11) all the xp pro pc on our network takes forever to download files. the network has 4 servers 2003 r2 and 2008 r2. You can navigate without problems, but when you download for example a 300 KB word doc it will take 5-10