Computer does not recognize the disc in the cd drive.

original title: media player 11 does not recognize the disc in the cd drive.

Media Player 11

I use Windows XP oper. system, my windows player works fine execpt when I place a cd in the drawer of rip to rip to my library WMP does not recognize that there is a disc in the drawer of thr. The problem started after I installed a vinal record of pc system, but he has always recognized that the disc was in rip drawer, if I put the disc in the drawer and WMP has closed and reopened. then it started to not recognize that a disk was in the drawer, even if I closed and reopened WMP with the disc in the drawer. Any solution to this problem would be greatly appericated. Thanks George

Hello

Remove the filter upper and lower filter and see if it helps.

r: clickStartand then click run

b:   In theOpen box, type regedit, and then click OK

c:   In the navigation pane, find and then click the following registry subkey:

HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Class\ {4D36E965-E325-11CE-BFC1-08002BE10318}

d: in the right pane, clickUpperFilters.

Note You can also see an UpperFilters.bak registry entry. You don't have to delete this entry. ClickUpperFilters . If you do not see the UpperFilters registry entry, you may still have to delete the LowerFilters registry entry. To do this, go to step g.

e: in theEdit menu, click delete.

f: when you are prompted to confirm the removal, clickYes

g:    In the right pane, clickLowerFilters.

Note If you do not see the LowerFilters registry entry, unfortunately this content can't help you. Go to the section"next steps"to learn how you can find more solutions or more help on the Microsoft Web site.

h: in theEdit menu, click delete.

i: when you are prompted to confirm the removal, clickYes

j:    Exit Registry Editor.

KC: restart the computer.

Important: This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs.

For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base:

322756 (http://support.microsoft.com/kb/322756/)

Hope this information helps.

Tags: Windows

Similar Questions

  • After installing service pack 2, computer does not recognize the cd drive

    Original title: after installation of service pack 2, computer does not recognize my cd drive, I deleted the computer recognizes the drive but the programs are not yet loads

    My burning software are not yet picking up the car, it says no recorder found or is just let me burn, I had none of these problems before I started to install the updates

    Hi Shon S,.

    Since you are facing problems after you remove the filters, you can try to uninstall and reinstall the DVD player and check.

    For more information, you can refer to the following article:

    Your CD or DVD drive is missing or is not recognized by Windows or other programs

    Hope this information is useful.

  • Computer does not recognize the CD Driver.

    My computer does not recognize my CD driver or does not burn anything.  Just used this mother's day so I know it worked.  In the Device Manager under DVD/CD rom players, there is the DVD A DS8A2 currently ATA Device.  It has a yellow triangle with a! inside. When I click on properties of this, he says that the device cannot start. Code 10.  Tried to find solutions, but it does not allow me to do.  This same thing has happened, but I do not remember how to fix.  Help.

    Try to take the cd player and plug in or go to the website of computer company and try to find drivers ex: dell, lenovo, sony, emichine ect.

    It has helped me.

  • Computer does not recognize the printer driver Canon ipf 8100

    I downloaded the driver fron Canon and installed on my 64 bit Windows 7 system, but the computer does not see the driver for my printer is still not installed

    Hi Larry,

    To better understand the issue, I would like to know if you receive any error messages. If Yes, what is the error message that is accurate and complete.

    It seems that the printer is compatible with windows 7.

    http://www.microsoft.com/en-us/windows/compatibility/win7/CompatCenter/ProductViewerWithDefaultFilters?TempOsid=win7&Locale=en-us&TextSearch=canon%2BIPF8100&Type=Both&CurrentPage=0&TotalPages=1&ShowCriteria=0&SortCriteria=Relevance&Compatibility=Unknown&LastRequested=14

    Method 1:
    Run the troubleshooter and check if that helps.

    Diagnose and automatically fix problems printing and printer

    http://support.Microsoft.com/mats/printing_problems/en-us

    Method 2:
    If the problem persists, try the procedure described in the article and check if it helps.

    Note: Try all the steps except the resolution of problems.

    Printer in Windows problems

    http://Windows.Microsoft.com/en-us/Windows/help/printer-problems-in-Windows

    Hope this information helps. Answer the post with an up-to-date issue report to help you further.

  • Want to reinstall XP but the computer does not recognize the cd drive and does not allow for any installation.

    Accidentally deleted some system files and now the computer won't allow me to install anything. Tried to install a new cd player to replace a corrupt, but it does not recognize drive. All the driver and OS install CD. Help.

    Fix missing files:

    Try to run the checker system (CFS) files.  Press start, select run, type: SFC/scannow

    SFC will ask your installation disc (which you must have if you are going to re - install), put it in the drive when requested.  Leave the SFC to replace all missing or corrupt files.

    To resolve the startup problem:

    Check your BIOS Setup and make sure the optical drive is enabled and listed before the hard drive in the boot order.  When you start, there will be a message, "type any key to boot from the CD-ROM."  Type any key (execpt shift, shift caps lock, NumLock, etc) will cause the CD to be initialized in the installation program.  (I use the space bar, it's an easy target.)

    In addition, it would be useful to know a few more things: 1) what edition and service pack level of Windows XP you are running?  (2) what is the model and manufacturer of the optical drive, please?

  • Recovering the Windows system does not recognize the hard drive

    Computer does not recognize the hard drive when booting.  Guard gives me 1782 disk error.  Then try to use the ROM installation thing and throw a disc hard test there is no option to test anywhere.  Computer was working fine this morning and then I stop when I turned it back on it was not properly start.

    I have a zt3000 running xp sp3

    someone please help me, thanks

    Hello

    Please reinsert the drive from the rear panel and check if the device detects the drive hard in case you have the same problem, then the hard drive is bad, you need to replace the hard drive and reinstall the operating system on the unit to return to its operating state.

  • Computer does not recognize the CD/DVD drive

    For these last days, my computer does not recognize the CD/DVD drive.  I have tried everything - publishers of registry, check the physical connections inside the computer, the system restore and install Fix - It programs.  However, the computer does not recognize this drive.  I also wonder if it is a hardware problem.  The light on the drive is a constant in green, and does not have the Open button.  And when I use the bent-paper-clip-in-the-little-hole and can open the drive, it will not read the disc.  Please advise...

    I fixed my problem with the BIOS operating system & not recognizing not not my DVD player to reinvest the solder on the motherboard.  You can find instructions on how to do it here: http://www.computerrepairtips.net/how-to-reflow-a-laptop-motherboard/

    There was a little crazy with my video drivers when I started first, but everything works after resetting the BIOS by default.

  • I have a My Passport to the top by car and I get error messages on this to be ejected (although it was still connected). Now my computer does not recognize the drive. All solutions?

    I have a My Passport to the top by car and I get error messages on this to be ejected (although it was still connected). Now my computer does not recognize the drive. All solutions?

    Drive, interface in the crankcase of training controller, or the USB port or the cable may be faulty.

  • my computer does not recognize the Device Manager cd/dvd/rom drive says corrupted or missing code 39

    my computer does not recognize the Device Manager cd/dvd/rom drive says corrupted or missing code 39

    Try following the steps under "Windows 7 or Windows Vista" in the MS KB article:

    http://support.Microsoft.com/kb/982116

    These measures, to remove the UpperFilters and LowerFilters, values if they exist, in the registry key named can help.

    Create a System Restore Point beforehand and restart the computer later.

  • Computer does not recognize the monitor after update of Win7.

    Computer does not recognize the monitor after update of Win7. Have a projector connected to the computer with the monitor; from clogging the last evening updates have been installed. When the computer has been restarted this morning the monitor is entered but did not detect a signal and fell asleep: do not get an image on the monitor or projector.  Suggestions?

    It is a laptop?

    And if you start in safe mode?

    Desktop

    Haven't tried safe mode
    Disconnected the projector, and then restarted; back to work now!
  • the computer does not recognize the printer memory card reader. HP photosmart 7660 printer

    The computer does not recognize the memory card from camera. The printer recognizes the memory card. So I can't transfer photos unless the camera is connected via USB. The printer is HP Photosmart 7660. Any suggestions?  Driver has been updated ' 09 and MS says I have the latest version of the driver.

    Ron

    The computer does not recognize the memory card from camera. The printer recognizes the memory card. So I can't transfer photos unless the camera is connected via USB. The printer is HP Photosmart 7660. Any suggestions?  Driver has been updated ' 09 and MS says I have the latest version of the driver.

    Ron

    Microsoft did not your hardware - done HP.

    All support for it - regardless of your operating system - is the manufacturer of the equipment.
    http://h10025.www1.HP.com/ewfrf/wc/softwareCategory?product=305364&LC=en&cc=us&DLC=en&lang=en&cc=us

  • My computer windows 8 HP Pavillion M8100n does not recognize the DVD drive or the SD card reader. Do you have any suggestions?

    My computer windows 8 HP Pavillion M8100n does not recognize the DVD drive or the SD card reader.  I have just upgraded to Windows 8 of Window Vista. Do you have any suggestions?

    Hello

    I see nothing unusual, except that there should be a "0001", or even "0002"...

    When you have made the registry change, you used the command line (Admin)?... the process may not work with the regular command prompt...

    Also, try to go to Device Manager, right click on your DVD drive, click on uninstall and restart.

  • my pc does not recognize the cd drive. I tried restoring the system without success.

    Windows does not recognize the cd drive

    Hello

    Step 1: Please do all the same underneath if you did some before as is often total
    a process that solves the problem.

    Try this - Panel - Device Manager - CD/DVD - double click on the device - driver tab.
    Click on update drivers (this will probably do nothing) - RIGHT click ON the drive - uninstall.
    RESTART this will refresh the default driver stack. Even if the reader does not appear to continue
    below.

    Then, work your way through these - don't forget the drive might be bad, could be a coward
    cable or slight corrosion on the contacts (usually for a laptop) and other issues.

    Your CD or DVD drive is missing or is not recognized by Windows or other programs
    http://support.microsoft.com/kb/314060 - a Mr Fixit

    Try this fix manually if the Fixit 314060 does not work
    http://www.pchell.com/hardware/cd_drive_error_code_39.shtml

    Your CD or DVD drive is missing or is not recognized by Windows or other programs-
    a Mr Fixit
    http://support.Microsoft.com/kb/982116

    The CD drive or the DVD drive does not work as expected on a computer that you upgraded to
    for Windows Vista
    http://support.Microsoft.com/kb/929461

    When you insert a CD or a DVD, Windows Vista may not recognize the disc
    http://support.Microsoft.com/kb/939052

    Your CD or DVD drive cannot read or write media - A Mr Fixit
    http://support.Microsoft.com/GP/cd_dvd_drive_problems

    CD/DVD drive does not appear in Windows Vista, or you receive this error in Windows
    Vista installation after booting from the DVD (AHCI)
    http://support.Microsoft.com/kb/952951
    Drive CD - R or CD - RW Drive is not recognized as a recordable device
    http://support.Microsoft.com/kb/316529/

    Hardware devices not detected or not working - A Mr Fixit
    http://support.Microsoft.com/GP/hardware_device_problems

    Another possibility is that the cables are loose. Remove ALL power, then make sure that the cables in both
    ends. Remove and replace, do not just tight. For laptops, you can often clean power and
    contacts data with a pencil eraser.

    Some DVD players do not use the Windows default drivers so check with the manufacturer of system and
    manufacturer of device to see if there is a firmware or drivers for your drive if necessary.

    ===============================

    Step 2: You have disc problems as the CD/DVD is actually 4 discs in 1 case (CD & DVD
    Burn and CD and DVD read). So it is not unusual for 1 or 2 operational so that other parts
    do it right.

    Did you follow the Troubleshooting Guide for the reader who still does not work? There are
    the entries in registry that the troubleshooter does not solve and those who "might" be the cause.

    Check with your Maker system and a device for the two possible firmware updates and
    the correct registry entries for your car.

    Here are the keys that I of course are those in question - for the subkeys of the CD/DVD drive
    as there will be other subkeys in these keys. Do not forget to ask specific keys involved as well as
    the parameters.

    HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Enum\IDE

    HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Hardware Profiles\0001\System\CurrentControlSet\Enum\IDE

    HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Class\ {4D36E965-E325-11CE-BFC1-08002BE10318}

    -----------------------------------------------------------------------

    You can probably find more info here and maybe even the exact registry for your CD/DVD settings
    drive from someone with the same model.

    Forums - a lot of expert real help
    http://Club.myce.com/

    CD/DVD units
    http://www.myce.com/storage/

    Use DevManView to locate the CD/DVD in the registry (be careful and do a prior Restore Point)
    nothing change) - find the DevManView device and then make a right click on it free in RegEdit.

    DevManView - free - an alternative to the standard Windows Device Manager, which displays all the
    devices and their properties in flat table, instead of the tree viewer
    http://www.NirSoft.NET/utils/device_manager_view.html

    I hope this helps.

    Rob Brown - MS MVP - Windows Desktop Experience: Bike - Mark Twain said it right.

  • Windows does not recognize the DVD drive at startup

    Laptop: Dell E6410 ATG wt / verzion A15 Bios

    OS: Windows 7 SP1 with the latest updates.

    The question I have is when I log on Windows 7, the laptop does not recognize the DVD drive. The reader will not be displayed in my computer or Device Manager. I can get around this physically ejecting the disc and reinsert. If I do this drive appears in my computer Windows and Device Manager. It will read DVDs and CDs fine. I am able to reproduce the problem above mentioned question if I restart the laptop. If I restart the laptop the DVD drive won't be recognized and reinsert the drive will get it appears again.

    This problem occurs if I try a DVD - RW drive and an old DVD - ROM drive. If I go into the BIOS before windows, I can see the BIOS recognizing drives ok but not when initially get into Windows without having to eject and inserting the disc.

    Thanks in advance for any help.

    I guess that this must be a hardware problem then.

    Seems odd.

    The only other thing I can think of, after reinstalling W7, is a BIOS problem eventually. A strange setting it may be an older version of BIOS with a bug in it. If you decide to update the bios, make sure that you get the latest version for your make and model PC and follow the instructions. You can destroy a PC with bad BIOS or update the procedure.

  • Dell Inspiron 531 s problem of power/does not recognize the hard drive

    My Office does not illuminate. I replaced the power supply. No, it powers on but does not recognize the hard drive. It gives an error as SATA 0 None SATA 1 no SATA 2 No. How do we know that the cables are properly connected. I feel like I'm very close to solving the problem but don't have a clue what that next step to follow

    The original PSU had 4 sets of cables and connectors.  The new power supply has 5 sets of son.

    aries7531

    From your post, I guess that the configuration of the system now recognizes the hard drive?

    If you do not have a floppy drive, then BIOS can find the player who isn't there, it returns this error.

    Make sure that the floppy drive [drive A] is disabled in the [BIOS] installation system, page 173, so that it is no longer looking for the disc and see if this stops the error message.

    If the hard drive is recognized in the configuration of the system, he now knows in windows "My computer" or in "disk management, [right click on 'My computer' and select 'Manage', then disk management]."

    Bev.

  • Tecra S3: Installation of Vista does not recognize the HARD drive

    I try to install Vista Ultimate on my Tecra S3, but installation does not recognize the HARD drive.

    I tried to find the driver for Vista for my computer, but not found RAID.
    Tried it with XP drivers, but no longer works.

    Do you have an idea where I can download Vista drivers for RAID?

    THX

    Hello

    Your suggestion is good. The Tecra S3 supports the RAID, and the RAID driver is required to install the OS on the HARD drive.
    On the European driver Toshiba page I found a RAID for XP driver.

    I put t know if this driver will run under Vista, but I recommend to test.
    The RAID XP 1.3.8.0 driver version can be downloaded from this site:
    http://EU.computers.Toshiba-Europe.com/cgi-bin/ToshibaCSG/download_drivers_bios.jsp?service=EU

    Please note; You can store the RAID driver on an external USB and Vista should recognize it!

    Good luck

Maybe you are looking for

  • New keyboard on Satellite L500 - 19 X does not work correctly

    Hello About a month ago, I spilled pepsi on my laptop and had sent for repair. I came home today and he had a new keyboard installed, among other things. But the new keyboard does not work properly. A bunch of key type is close to letters instead. Fo

  • R7800 will not take static IP address entry

    I can't get my new R7800 to accept a static IP address entry. He returns constantly with an invalid IP address entry warning message. My router R7000 put in place and works perfectly using the same static IP address implemented. My R7800 is running t

  • text file with header data

    Hello for my test application, I want to store test data in a text file with header. It should be like this: name, series, count, current, min. Max run Mister Smith 1234567890 111 10 1000 data: 1 345 34 2 355 23 3 360 34 ... The first row are only on

  • How to get windows media Center in windows developer preview?

    How to get windows media Center in windows developer preview?

  • Lower center of the screen limits heats up

    Hello The lower central part of the limit of the screen of the Lenovo 3000 N100 heats, before (screen) and rear (coverage). I noticed that back this area has a crack. What is the solution, what I need to change the screen or cover or just need to clo