Computer does not start after running the utility Boot Lenovo.

Hello
I replaced the power supply with a CX550M of Corsair, increased memory by exchanging the 4 GB to 8 GB for a 16 GB total, I added a hybrid 2 TB Seagate HDD and all worked fine until yesterday, about 1 month.
Yesterday, I decided to run all the tests of the Lenovo startup disk and after that I restarted, the computer does not start.
When I press the power button, the fan starts and it stops after 3 or 4 seconds and nothing happens, the monitor says no signal, I removed the external USB disk and printer, I reoved the second drive and the same thing heppens.
Any idea what this problem could be? Would it be a bad power supply?
Thank you

Mario

Resolved, I erased the memory CMOS, moved to following ankle boot, back up the cmos.

Thank you

Tags: Lenovo Desktops

Similar Questions

  • computer does not start after the Windows XP logo window

    Windows xp home edition
    service pack 2
    Dell inspiron 1501

    1. computer does not start after the Windows XP logo window
    2 works well in safe mode, even connect to the external monitor
    3. I reinstalled xp many times, problem stil exist.

    All the answers?

    Hi dhanushm,

    1. What happens after the Windows logo screen?
    2. You receive an error message?
    3. You have security software installed on the computer?
    4. Have you performed an installation clean Windows XP and even after that this problem exists?

    Method 1

    As the computer starts up fine in safe mode there is a possibility that some third-party programs installed on the computer is the origin of the problem.

    I suggest that you configure the computer in a clean boot state and check if it helps.

    To help resolve the error and other messages, you can start Windows XP by using a minimal set of drivers and startup programs. This type of boot is known as a "clean boot". A clean boot helps eliminate software conflicts.

    See section to learn more about how to clean boot.

    How to configure Windows XP to start in a "clean boot" State

    http://support.Microsoft.com/kb/310353

    Reset the computer to start as usual

    When you are finished troubleshooting, follow these steps to reset the computer to start as usual:

    1. Click Start , and then click run.
    2. Type msconfig , and then click OK.
      The System Configuration utility dialog box appears.
    3. Click the general tab, click Normal Startup - load all device drivers and services , and then click OK.
    4. When you are prompted, click restart to restart the computer.

    Method 2

    If fails it above step can refer to the article below and try the steps mentioned, check if it helps.

    After the Windows Logo appears or after you log in to Windows, a Windows XP computer cannot display the wallpaper, a black screen or a blue screen

    http://support.Microsoft.com/kb/318027

  • Computer does not start after the screen of the bios, Compaq Presario SR1023WM

    Ok. Trying to fix a friend's computer and seem to have met a strange barrier.

    Problem: The computer does not start after the bios screen.

    Details: When you turn on the computer, the compaq logo with intel inside is and has the < F1 Setup > and < F10 System Recovery > options listed as well.  And that's it as far as the computer becomes.  After that the computer just locked up, no work of buttons on the keyboard lights keyboard ect ect.  I tried the puree on the F1 key, as soon as I turn on the computer and I can handle so he can say * entering setup * but it freezes again after this point.  I already tried to eliminate the possible sources of the problem, removed all expansion cards, HDD and Dvd Rom module only disconnected, only memory (256 MB ddr 2700), power, vga and keyboard connected.  Ive also used the jumper on the motherboard to clear the cmos, hoping that would solve the problem without success.  I tried using a different memory stick and different memory as well...  Tried to use both a ps2 and a usb keyboard... Ive even tried pulling the rider for the protection of the bios password (even if she did not have a password on it, just try everything I can think of).

    The installed bios version is 3.1, and that's all that I know on the computer at this point, except that the website tells me to him.

    http://h10025.www1.HP.com/ewfrf/wc/product?product=411354 & LC = on & CC = US & DLC = in & Submit.y = 5 & Submit.x = 3 & lang = to & CC = US <-link to the Web page for the model #.

    I'm basically at a loss on this one, so if someone feels scroll line-by-line of their brains on this one, I'd be very happy.

    I have a pretty strong understanding of computer repair, so feel free to give me something to try.

    If you need more information out of me, let me know as well.

    Try to clear the CMOS again but this time remove CMOS battery and hold the power button on a few seconds. Replace the battery, then try to start back to the top.

    At the back of the pc is the condition of the PSU led green or flashing?

  • You can save a broken computer? My computer does NOT start after the blue hp screen.

    In the past months, my computer has been the object of a freezing randomly, and Ctrl + Alt + Delete does not work. I stopped him via the power button. Sometimes, when I start it again, the computer moniter shows nothing but a black screen and the computer sounds different when it starts normally. When this happens, I turn it off again hit the left side of the desktop and turn on again. Whenever I do this, the computer starts normally, and I go on the computer use.

    Yesterday morning, after a break of 2 days, acess my computer and it is random freezing thing once again. I force close down as one normally do, and the computer does not start and displays the same black screen and the same fan/air weird sound. I stopped him and I hit the side RIGHT this time, I think and when I turn on the computer, the usual blue HP screen appears with the establishment, boot, diagnostics and system recovery things. HOWEVER, after this screen, a black screen will appear with this weird blue symbol on the upper left corner, I have never seen this and it looks like a circle with a triangle and a Pentagon below and it remains essentially on this screen forever. When I try to hit the establishment, boot, diagnostics and the shortcuts to system recovery, on the lower left side of the screen, it says "Menu boot loading...". ' or whatever the shortcut of loading represents, but nothing ever happens. When I press the other keys, this tapping noise comes from the computer at each tap of the keyboard.

    I have no idea what to do, and at this point, my first priority is to save important files on the computer. Does anyone know what is the problem? I want her more than a problem of system rather than a virus problem because refusing the boot black screen thing lasts for years. My computer is 3-4 years. I enclose a sketch of what looks like the weird symbol.

    MY COMPUTER WORKS NOW!

    With the flash drive, I was able to access the BIOS, which before, I couldn't.

    Eventually my computer was in some strange sort of lockdown setting, I switched it back to activate and now its work! I remember save important things in the future. Thank you very much for your help!

  • computer does not start after the installation of vista updates.

    computer does not start after the installation of vista updates. Startup Repair is also not working. event name: Startup Repair v2, prob GIS. 1: automatic failover, prob GIS 2: 6.0.6000.16386.6.0.6001.1800, prob 3:6, prob prob 5 and 6 GIS GIS sig, 4:720907: corrupt file, prob GIS 7: 3221226021, 8:3, prob GIS GIS prob 9: repair wrp, prob GIS 10; 2, 0 s version: 6.0.6000.2.0.0.256.1. In addition, none of these advanced recovery options seem to work.

    Hello

    Try the steps suggested by David Y post dated November 2, 2010 in the link given below and check if that helps.

    http://social.answers.Microsoft.com/forums/en-us/w7repair/thread/a6071159-db22-4076-b5d8-31f446dbdf32

    Hope that information was useful

  • Compaq 6200 PRO MT: Makes the computer does not start after upgrade CPU

    I have the HP Compaq 6200 PRO PC of MT 615114-001 motherboard and processor Intel Celeron CPU (LGA 1155). After I changed the CPU for Intel Core i5 (LGA 1155) computer does not start. He begins a minute (less than one second) and stops again. No beeps. After you have installed the Celeron back everything works fine. i5 CPU is brand new. What can be?

    In my previous post, I explained the reason it has not worked, and listed the CPU that will work.

    HP tests CPU in the laboratory and publishes a list of processors that will work in a notebook.

    Notebook motherboard BIOS has a list of processors that will work. If it is installed, which is not encoded as OK in the BIOS ROM file, then this will not work.

    Processors published (in the maintenance guide & Service for your nttebook series model) are available in models that can be deilvered in State CTO (configured to order).

  • Z600: computer does not start after the installation of the 5 TB SATA drive

    My z600 refurbished does not start after the installation of a SATA of Toshiba 5 to disk.  After removing the drive, the computer starts.  I have my computer too old to handle a 5 TB drive, I something wrong or is the DOA drive?

    Thanks for the info.  I added the GPT to my search and discovered what had to be done in disk management.  Here is a page with step by step instructions and photos.  http://www.howtogeek.com/193669/whats-the-difference-between-GPT-and-MBR-when-partitioning-a-drive/

  • M127FW MFP: Computer does not start after the installation of the MFP M127FW

    My computer does not start on my hard drive after installation of my new printer MFP M127FW unless I have first of all disconnect the USB cable between the printer and then turn on the computer.  My BIOS is set to boot from my drive hard, not from a USB key, so that makes installing the drivers M127FW MFP and software do on my computer?  I guess it has something to do with the Smart Install feature.

    "On the printer, press Setup, maintenance, Smart Install and stop."

    It worked.  Thank you.

  • Computer does not start after installing a new graphics card

    I am owner of a HP Pavilion H8-1020 with a processor intel i7 - 2600 s Windows 7 and am trying to upgrade my Radeon hd 6570 to a Gigabyte AMD Radeon R9 280 OC. I improved my diet for a Corsair CX750 to meet the requirements of power and installed with number. After the installation of the new card, which as far as I can tell is well seated in the pci slot and correctly connected to the PSU, my computer does not start.

    System powers on, all fans of begin to run including the fans on the new graphics card, but it does not begin the boot process, no entry is received at my monitors, no light on the keyboard, my OS starts loading, I can turn off the system without the delay that will flow normally. Then I reinstalled my old graphics card and the computer started as usual.

    Now, assuming that the card is not DOA, which unfourtunatly I have no way to verify, and I'd like to see if it could be another problem before going through the process of restitution. I did some reading on the internet, which helped, but did not help for a technological neophyte like me.  Now, I know a few things that could cause this problem but lack the necessary skills to determine what question is making me. What I've read, these could be possible questions:

    1: my new graphics card is not compatible with my motherboard. It's something I know now that I should have checked before buying and something I should theoretically be able to do it now, but I am at a loss on how to do it. My card is compatible with my motherboard?

    2 could be a BIOS problem. I updated my bios driver with the version provided by the HP site. I am running FRIEND 7.16 05/10/2011.  And from what I've read it might have something to do with my bios to UEFI mode and I would need to go to a legacy mode so he can recognize a new device, is it true? I am extremely wary of messing with my BIOS settings for fear of bricking my system. How can I check my current BIOS settings are and what I should change and how would approach I change them? Will one of these changes affect my system if they are not what is not causing the problem?

    In addition to these issues, anyone know any other matter which may be the cause of the problem that I should look for? Thanks for any help.

    Hello @Eric_Z,

    I can see why you are having problems with your new graphics card, and to get to the fast response that your motherboard is not compatible with the new graphics card that you have purchased. And here's why.

    Your motherboard according to the page HP Pavilion HPE h8-1020 Desktop PC product specifications is the Carmel motherboard, which has the following expansion slots:

    • A PCI Express x 16
    • Three PCI Express x 1 connectors
    • A PCI Express Mini Card x 1

    As there is no version indicated for your PCI Express x 16 it slot means that it is version 1.

    Now, your previous graphics card was a PCI Express 2.1 x 16, which means that it was version 2 and compatible with your PCI Express x 16 slot on your motherboard. However, the new card is PCI Express 3.0 and will not work in your motherboard due to a compatibility break. While the technology is supposed to be compatible there are many cases where it is not, and I'm afraid that you meet one of these cases.

    I am offering an overclock.net article entitled: the final answer to the controversial compatibility of PCIe x 16 version. where your situation has been tested and examined.

    I hope this helps. Have a great day and thank you for display on the HP Forums!

  • Computer does not start after installing new graphics card

    HP-envy h8-1503
    I7 - 3770 k 3.5 GHZ
    10 GB of Ram
    Windows 8.1

    I tried to install a new edition of diamond Raedon 7770 to replace my old 7570 and when I try to start the computer I get 6 long beeps and the power light flashes 6 times. Everything is plugged in right and the video card turns on. It will not be output to the screen tho and the computer does not start!

    I fixed it, the problem was the safe boot in my bios, when I disabled the system booted and worked perfectly since! Thanks for the advice tho!

  • computer does not start after installing video card

    I, m new here so please bear with me.  I have a PC HP Pavilion Media Center TV (m7434n) I'm trying to replace the video card (Nvidia GeForce 6200SE with Turbo Cache) in. I am trying to replace it with a Nvidia EVGA 8400GS. I delete all the nvidia drivers, make sure that the pci-e card is used in the implementation. I have then to remove the old card and install a new one. When I try to start the computer, fans turn on but that's all.  There is nothing on the monitor.  The computer does not start. I replaced the power supply bestec 300 watts with a new antec brand 430 watt power supply.  When I reinstalled the old video card, the computer starts ok. I tried to replace the video card with an ATI Radeon HD5550 too and it's the same thing (the computer would not start), reinstall the old card and it starts up fine. Any help would be greatly appreciated.

    Gary,

    You may have a compatibility issue with the ATI HD 5550 and 2006 PC model.  I've seen other posts where ATI 5xxx video card did not work in older HP PCs.

    When you are referring to the installation of the older video card do you mean going back to the integrated video card?  Moving the video cable to the card installed?

    Install the NVIDIA 8400GS and connect the video cable. Now follow the instructions for clear the CMOS.

  • Computer does not start after the screen goes blank &amp; Compaq.

    Hello

    A few weeks ago, I turned on my PC and it showed at the Compaq screen and then went to a blank screen & would not respond. I held the switch button to turn it off and after 4 attempts, it start fine. Next time, it took 20 attempts to initialize and now it does not start, it will be maybe if I try like 100 times he can do... The problem is when the Compaq screen comes up it comes only for like a second so I know that it does not start, if the Compaq screen stays for a few seconds as 3 + I know it will load windows and start.

    History > the computer originally had XP and has been replaced with VISTA memory was 2 * 512MB, but it was a bit slow and I was advised to upgrade. I bought 2 * 1 GB memory and put it in my PC a few months there may be 5 + had no problem so far.

    I tried the following:

    Remove the memory and replace it. Remove the 2 * 1 GB of memory and its replacement by the Moose 2 * 512MB to check if the memory is at fault.

    Cleaning of the dust around the fan (at this point, I removed the fan over the CPU and cleaned the thermal compound from the CPU to make it nice and shiny, only tried to start one time after that for a few seconds heard blowing fan and turend it took off. Depuis_lors, I realized that it wasn't just muck and had a purpose na derwiche put a little more on)

    Remove the battery of the BIOS for half a day

    Move jumpers CMOS from1, 2 to 2, 3 positions

    I can not get into the same if BIOS start and hold F1 he will show me the BIOS for a second and then go to a black screen.

    Specifications of the computer

    Compaq Presario SR1629UK desktop PC

    Details can be found in the following link

    http://support.HP.com/us-en/document/c00579251

    Your help would me much appreciated...

    Hi guys,.

    Thanks for your help, I wanted to just give you a batch update. After the grueling process of verifying the destop, memory suppression, cleaning it & all the other techo checks. I gave my pc to somone to look to the he tried not to turn on he opened it removed cleaning my thermal paste back on and told me it was working fine.

    When I bought home all happy, I realized that I had the same problem, I borrowed another monitor and found it worked well! So the question is with my monitor, if anyone has the same problem first check another monitor.

  • H8 - 1280t - QC461AV #ABA: desktop HP - computer does not start after the installation (Windows 10) video card

    So, I just bought a new video card an XFX R9-390 and a new HX1200i POWER supply corsair (overkill ik ) that I put on a card mother IPIWB-PB for my 3 years old HP PC, and the new stupid video card is not working. the PC just does not start, I see is a black screen. My monitor is an HP 2311gt and I can't use my computer with the old video card no probs, BUT whenever I have to install the new card does not detect my monitor just and I only see a blank screen. I HAVE NO IDEA HOW I'M DOING. Help, please

    PS. I have RMA the new power supply and the video card and they got to check and send back to me, so I know that the two pieces of equipment are working very well AND of course I am currently using my PC with the old video card

    Wiraqocha, here is the link to start safe for HPs with Win 10 and instructions to enter the BIOS. It may be useful:

    HP PC - secure boot (Windows 10)

  • P6-2009it: the computer does not start after you install a new videocard (msi Gtx 960)

    Intel Core i3-2120 Socket H2 (LGA1155)

    Foxconn Intel H61 2ABF (Cougar Point)

    P6-2009it

    Power supply - corsair CX500

    Do not run the single image windows start and all. I can't go anywhere, WHAT BIOS is not also responsible.

    Right now is the radeon hd 6950 2 GB video card.

    BIOS updated to the latest version 7.16 - has not helped

    remove the previous video card driver - has not helped

    I leave the battery on the mother 10 minutes card - has not helped

    Nothing helps, what's the problem?

    Hirurgrrr, welcome to the forum.

    The problem you are experiencing is caused by the fact that the GTX 960 requires UEFI in the motherboard instead of a standard BIOS.  HP didn't start using UEFI until mid-October 2012.  The last series of video cards that does not need UEFI is the GT 640.

    Please click on the Thumbs up button '+' if I helped you and click on "Accept as Solution" If your problem is resolved.

  • Computer does not start after the installation of Win XP SP3

    original title: ServicePack 3 does not work

    After loading service pack 3 my computer does not upwards, unless I use safe mode. It restores not to any restore point. I uninstall and go back to service pack two and get constant reminders to update three when it won't work. After saying it works fine if a little slow in two so is there any point of update.

    Recently, I reset my computer to factory settings to erase the disc from loads of unwanted waste and programs. Reloaded ServicePack two, he wouldn't go back with gel. After reading the old posts, I found a link to Jespers blog. It contained a small tool that intelPPM problems detected and then given the option to turn off the setting. http://msinfluentials.com/blogs/jesper/archive/2008/05/08/does-your-amd-based-computer-boot-after-installing-xp-sp3.aspx.

    This fixes the problem and service pack three charges and now works fine. The tool is loaded in seconds.

Maybe you are looking for

  • HP Pavilion dv8000

    I need to replace the keyboard on my laptop.  Looked at the parts list but do not know what the difference between a dv800av and dv800avr is?  Anyone can help or tell me what keyoard I need to order? Thank you!

  • Microsoft Flight Simulator FSX ceased work and the error 1722 / 1603 when trying to reinstall

    Try to install FSX after I uninstalled because it fail to start a running OK OK before that.  Get error 1722 - there is a problem with this Windows Installer package.  A program run as part of the Setup did not finish as expected.  Contact your selle

  • Weak signal since I moved.

    I recently moved into a new House, it's less than six miles from my old House. My signal it is horrible. I was wondering if anyone has any advice on how my signal booster. I have a razr droid and love the phone, but I need reception. Thank you.

  • Where to find the Plug-ins for Windows Media Player?

    When I insert a VCD and play a video, he asks a Plug-ins for Windows Media Player, anyone have any suggestions on where to find plugins for Windows Media Player? Thanks for all the suggestions

  • Start-up error message RunDLL

    At startup I get the RunDLL error telling me "Error loading C:\Users\USERNAME\kloadpCE.dll" the specified module could not be found.  Also get a second message "error loading C:\Users\USERNAME\AppData\Roaming\MICROS~1\Windows\STARTM~1\Programs\Startu