computer does not start after update

what computer starts without updates without problems.
When the computer starts after a update it does not start and goes into the Startup Repair. after repair, I check: diagnosis and repair of the details:
the root cause of watch - start criticalfile c:\ntoskrnl.exe is corrupt. with a 0xa error code

can I fix it myself?

horticulturist,
Did you run the System File Checker?  If so, what were the results?  If you haven't done so already, you will need to run (sfc/scannow) so that it can check your system files for all questions.  Also this happens after any update is installed, or only the current links that are pending?  I suggest try to install an update at a time and see if you are able to get the updates installed or not.

Mike - Engineer Support Microsoft Answers
Visit our Microsoft answers feedback Forum and let us know what you think.

Tags: Windows

Similar Questions

  • computer does not start after the installation of vista updates.

    computer does not start after the installation of vista updates. Startup Repair is also not working. event name: Startup Repair v2, prob GIS. 1: automatic failover, prob GIS 2: 6.0.6000.16386.6.0.6001.1800, prob 3:6, prob prob 5 and 6 GIS GIS sig, 4:720907: corrupt file, prob GIS 7: 3221226021, 8:3, prob GIS GIS prob 9: repair wrp, prob GIS 10; 2, 0 s version: 6.0.6000.2.0.0.256.1. In addition, none of these advanced recovery options seem to work.

    Hello

    Try the steps suggested by David Y post dated November 2, 2010 in the link given below and check if that helps.

    http://social.answers.Microsoft.com/forums/en-us/w7repair/thread/a6071159-db22-4076-b5d8-31f446dbdf32

    Hope that information was useful

  • Computer does not start after the screen of the bios, Compaq Presario SR1023WM

    Ok. Trying to fix a friend's computer and seem to have met a strange barrier.

    Problem: The computer does not start after the bios screen.

    Details: When you turn on the computer, the compaq logo with intel inside is and has the < F1 Setup > and < F10 System Recovery > options listed as well.  And that's it as far as the computer becomes.  After that the computer just locked up, no work of buttons on the keyboard lights keyboard ect ect.  I tried the puree on the F1 key, as soon as I turn on the computer and I can handle so he can say * entering setup * but it freezes again after this point.  I already tried to eliminate the possible sources of the problem, removed all expansion cards, HDD and Dvd Rom module only disconnected, only memory (256 MB ddr 2700), power, vga and keyboard connected.  Ive also used the jumper on the motherboard to clear the cmos, hoping that would solve the problem without success.  I tried using a different memory stick and different memory as well...  Tried to use both a ps2 and a usb keyboard... Ive even tried pulling the rider for the protection of the bios password (even if she did not have a password on it, just try everything I can think of).

    The installed bios version is 3.1, and that's all that I know on the computer at this point, except that the website tells me to him.

    http://h10025.www1.HP.com/ewfrf/wc/product?product=411354 & LC = on & CC = US & DLC = in & Submit.y = 5 & Submit.x = 3 & lang = to & CC = US <-link to the Web page for the model #.

    I'm basically at a loss on this one, so if someone feels scroll line-by-line of their brains on this one, I'd be very happy.

    I have a pretty strong understanding of computer repair, so feel free to give me something to try.

    If you need more information out of me, let me know as well.

    Try to clear the CMOS again but this time remove CMOS battery and hold the power button on a few seconds. Replace the battery, then try to start back to the top.

    At the back of the pc is the condition of the PSU led green or flashing?

  • computer does not start after the Windows XP logo window

    Windows xp home edition
    service pack 2
    Dell inspiron 1501

    1. computer does not start after the Windows XP logo window
    2 works well in safe mode, even connect to the external monitor
    3. I reinstalled xp many times, problem stil exist.

    All the answers?

    Hi dhanushm,

    1. What happens after the Windows logo screen?
    2. You receive an error message?
    3. You have security software installed on the computer?
    4. Have you performed an installation clean Windows XP and even after that this problem exists?

    Method 1

    As the computer starts up fine in safe mode there is a possibility that some third-party programs installed on the computer is the origin of the problem.

    I suggest that you configure the computer in a clean boot state and check if it helps.

    To help resolve the error and other messages, you can start Windows XP by using a minimal set of drivers and startup programs. This type of boot is known as a "clean boot". A clean boot helps eliminate software conflicts.

    See section to learn more about how to clean boot.

    How to configure Windows XP to start in a "clean boot" State

    http://support.Microsoft.com/kb/310353

    Reset the computer to start as usual

    When you are finished troubleshooting, follow these steps to reset the computer to start as usual:

    1. Click Start , and then click run.
    2. Type msconfig , and then click OK.
      The System Configuration utility dialog box appears.
    3. Click the general tab, click Normal Startup - load all device drivers and services , and then click OK.
    4. When you are prompted, click restart to restart the computer.

    Method 2

    If fails it above step can refer to the article below and try the steps mentioned, check if it helps.

    After the Windows Logo appears or after you log in to Windows, a Windows XP computer cannot display the wallpaper, a black screen or a blue screen

    http://support.Microsoft.com/kb/318027

  • Photoshop does not start after update CC 2015 and I can't install new applications... What can I do?

    Photoshop does not start after update CC 2015 and I can't install new applications... What can I do?

    If you leave CC 2015 Installer remove older versions of Photoshop you can re - install older versions using the creative Cloud Desktop application or through direct downloads, you can install.

    Direct download links of Adobe CC 2014: 2014 creative cloud release | ProDesignTools

    Download new Adobe CC trials: direct links (no Assistant Manager) | ProDesignTools

    Download Creative Suite 6 applications

  • Computer does not start after installing a new graphics card

    I am owner of a HP Pavilion H8-1020 with a processor intel i7 - 2600 s Windows 7 and am trying to upgrade my Radeon hd 6570 to a Gigabyte AMD Radeon R9 280 OC. I improved my diet for a Corsair CX750 to meet the requirements of power and installed with number. After the installation of the new card, which as far as I can tell is well seated in the pci slot and correctly connected to the PSU, my computer does not start.

    System powers on, all fans of begin to run including the fans on the new graphics card, but it does not begin the boot process, no entry is received at my monitors, no light on the keyboard, my OS starts loading, I can turn off the system without the delay that will flow normally. Then I reinstalled my old graphics card and the computer started as usual.

    Now, assuming that the card is not DOA, which unfourtunatly I have no way to verify, and I'd like to see if it could be another problem before going through the process of restitution. I did some reading on the internet, which helped, but did not help for a technological neophyte like me.  Now, I know a few things that could cause this problem but lack the necessary skills to determine what question is making me. What I've read, these could be possible questions:

    1: my new graphics card is not compatible with my motherboard. It's something I know now that I should have checked before buying and something I should theoretically be able to do it now, but I am at a loss on how to do it. My card is compatible with my motherboard?

    2 could be a BIOS problem. I updated my bios driver with the version provided by the HP site. I am running FRIEND 7.16 05/10/2011.  And from what I've read it might have something to do with my bios to UEFI mode and I would need to go to a legacy mode so he can recognize a new device, is it true? I am extremely wary of messing with my BIOS settings for fear of bricking my system. How can I check my current BIOS settings are and what I should change and how would approach I change them? Will one of these changes affect my system if they are not what is not causing the problem?

    In addition to these issues, anyone know any other matter which may be the cause of the problem that I should look for? Thanks for any help.

    Hello @Eric_Z,

    I can see why you are having problems with your new graphics card, and to get to the fast response that your motherboard is not compatible with the new graphics card that you have purchased. And here's why.

    Your motherboard according to the page HP Pavilion HPE h8-1020 Desktop PC product specifications is the Carmel motherboard, which has the following expansion slots:

    • A PCI Express x 16
    • Three PCI Express x 1 connectors
    • A PCI Express Mini Card x 1

    As there is no version indicated for your PCI Express x 16 it slot means that it is version 1.

    Now, your previous graphics card was a PCI Express 2.1 x 16, which means that it was version 2 and compatible with your PCI Express x 16 slot on your motherboard. However, the new card is PCI Express 3.0 and will not work in your motherboard due to a compatibility break. While the technology is supposed to be compatible there are many cases where it is not, and I'm afraid that you meet one of these cases.

    I am offering an overclock.net article entitled: the final answer to the controversial compatibility of PCIe x 16 version. where your situation has been tested and examined.

    I hope this helps. Have a great day and thank you for display on the HP Forums!

  • Compaq 6200 PRO MT: Makes the computer does not start after upgrade CPU

    I have the HP Compaq 6200 PRO PC of MT 615114-001 motherboard and processor Intel Celeron CPU (LGA 1155). After I changed the CPU for Intel Core i5 (LGA 1155) computer does not start. He begins a minute (less than one second) and stops again. No beeps. After you have installed the Celeron back everything works fine. i5 CPU is brand new. What can be?

    In my previous post, I explained the reason it has not worked, and listed the CPU that will work.

    HP tests CPU in the laboratory and publishes a list of processors that will work in a notebook.

    Notebook motherboard BIOS has a list of processors that will work. If it is installed, which is not encoded as OK in the BIOS ROM file, then this will not work.

    Processors published (in the maintenance guide & Service for your nttebook series model) are available in models that can be deilvered in State CTO (configured to order).

  • Computer does not start after running the utility Boot Lenovo.

    Hello
    I replaced the power supply with a CX550M of Corsair, increased memory by exchanging the 4 GB to 8 GB for a 16 GB total, I added a hybrid 2 TB Seagate HDD and all worked fine until yesterday, about 1 month.
    Yesterday, I decided to run all the tests of the Lenovo startup disk and after that I restarted, the computer does not start.
    When I press the power button, the fan starts and it stops after 3 or 4 seconds and nothing happens, the monitor says no signal, I removed the external USB disk and printer, I reoved the second drive and the same thing heppens.
    Any idea what this problem could be? Would it be a bad power supply?
    Thank you

    Mario

    Resolved, I erased the memory CMOS, moved to following ankle boot, back up the cmos.

    Thank you

  • Z600: computer does not start after the installation of the 5 TB SATA drive

    My z600 refurbished does not start after the installation of a SATA of Toshiba 5 to disk.  After removing the drive, the computer starts.  I have my computer too old to handle a 5 TB drive, I something wrong or is the DOA drive?

    Thanks for the info.  I added the GPT to my search and discovered what had to be done in disk management.  Here is a page with step by step instructions and photos.  http://www.howtogeek.com/193669/whats-the-difference-between-GPT-and-MBR-when-partitioning-a-drive/

  • You can save a broken computer? My computer does NOT start after the blue hp screen.

    In the past months, my computer has been the object of a freezing randomly, and Ctrl + Alt + Delete does not work. I stopped him via the power button. Sometimes, when I start it again, the computer moniter shows nothing but a black screen and the computer sounds different when it starts normally. When this happens, I turn it off again hit the left side of the desktop and turn on again. Whenever I do this, the computer starts normally, and I go on the computer use.

    Yesterday morning, after a break of 2 days, acess my computer and it is random freezing thing once again. I force close down as one normally do, and the computer does not start and displays the same black screen and the same fan/air weird sound. I stopped him and I hit the side RIGHT this time, I think and when I turn on the computer, the usual blue HP screen appears with the establishment, boot, diagnostics and system recovery things. HOWEVER, after this screen, a black screen will appear with this weird blue symbol on the upper left corner, I have never seen this and it looks like a circle with a triangle and a Pentagon below and it remains essentially on this screen forever. When I try to hit the establishment, boot, diagnostics and the shortcuts to system recovery, on the lower left side of the screen, it says "Menu boot loading...". ' or whatever the shortcut of loading represents, but nothing ever happens. When I press the other keys, this tapping noise comes from the computer at each tap of the keyboard.

    I have no idea what to do, and at this point, my first priority is to save important files on the computer. Does anyone know what is the problem? I want her more than a problem of system rather than a virus problem because refusing the boot black screen thing lasts for years. My computer is 3-4 years. I enclose a sketch of what looks like the weird symbol.

    MY COMPUTER WORKS NOW!

    With the flash drive, I was able to access the BIOS, which before, I couldn't.

    Eventually my computer was in some strange sort of lockdown setting, I switched it back to activate and now its work! I remember save important things in the future. Thank you very much for your help!

  • M127FW MFP: Computer does not start after the installation of the MFP M127FW

    My computer does not start on my hard drive after installation of my new printer MFP M127FW unless I have first of all disconnect the USB cable between the printer and then turn on the computer.  My BIOS is set to boot from my drive hard, not from a USB key, so that makes installing the drivers M127FW MFP and software do on my computer?  I guess it has something to do with the Smart Install feature.

    "On the printer, press Setup, maintenance, Smart Install and stop."

    It worked.  Thank you.

  • Computer does not start after installing new graphics card

    HP-envy h8-1503
    I7 - 3770 k 3.5 GHZ
    10 GB of Ram
    Windows 8.1

    I tried to install a new edition of diamond Raedon 7770 to replace my old 7570 and when I try to start the computer I get 6 long beeps and the power light flashes 6 times. Everything is plugged in right and the video card turns on. It will not be output to the screen tho and the computer does not start!

    I fixed it, the problem was the safe boot in my bios, when I disabled the system booted and worked perfectly since! Thanks for the advice tho!

  • computer does not start after installing video card

    I, m new here so please bear with me.  I have a PC HP Pavilion Media Center TV (m7434n) I'm trying to replace the video card (Nvidia GeForce 6200SE with Turbo Cache) in. I am trying to replace it with a Nvidia EVGA 8400GS. I delete all the nvidia drivers, make sure that the pci-e card is used in the implementation. I have then to remove the old card and install a new one. When I try to start the computer, fans turn on but that's all.  There is nothing on the monitor.  The computer does not start. I replaced the power supply bestec 300 watts with a new antec brand 430 watt power supply.  When I reinstalled the old video card, the computer starts ok. I tried to replace the video card with an ATI Radeon HD5550 too and it's the same thing (the computer would not start), reinstall the old card and it starts up fine. Any help would be greatly appreciated.

    Gary,

    You may have a compatibility issue with the ATI HD 5550 and 2006 PC model.  I've seen other posts where ATI 5xxx video card did not work in older HP PCs.

    When you are referring to the installation of the older video card do you mean going back to the integrated video card?  Moving the video cable to the card installed?

    Install the NVIDIA 8400GS and connect the video cable. Now follow the instructions for clear the CMOS.

  • Computer does not start after Windows update

    I built my computer in December last year, which makes it less than a year. It has worked fine until this last week when I decided to give a few necessary windows updates a lot. I decided to download and install all night, and now it does not start. I get nothing on the screen. I don't get the safe mode options. I didn't get last known good configuration options. I don't not even a splash screen. After a full minute, it turns off again, regardless of how many times I turn it back on. It happened for a few days. Are no external hard drives not connected; only an intern. The only devices I plugged are my keyboard and mouse. Can anyone offer a solution? Whatever happened to you?

    I am running Windows 7 Ultimate Edition.

    The first time I tried to start after downloading the updates, he went to the boot screen windows 7 usual, that clear blue that says it configures windows and not turn off the computer during the process. Before we were told: "Welcome to Windows," he said "Shutting Down", but not before the configuration of progress has reached 100%. At this time, everything seemed normal. After the computer turns.

    Hello

    To fix your problem, you can follow the steps on this link. You can perform troubleshooting listed on this site by clicking here. The listed on these links troubleshooting steps are applicable to Windows 7 and more.

    Let us know how it goes.

    Best regards

  • HP 15-af131dx: computer HP laptop does not start after update AMD video drivers

    Hello, my laptop HP 15-af131dx would not start after I have updated to the latest video drivers from AMD. After update, my phone was really slow, so I decided to restart it. When I tried to start up, most of the time, she would get to the windows logo with the symbol of loading under it and crashed. Sometimes arise windows recovery, but using it would only make it appear an error message. After a few tries, I was able to boot into windows safe mode and restore my video drivers. This corrects the problem, but I would like to know why this is happening and if the update of my video drivers by importing.

    . Hi @HPlaptop5,

    I hope you enjoy your visit to the HP's Support Forums. I understand that you have a problem with video drivers. I'll be happy to help you.

    You can also find your drivers to support.hp.com.

    The latest HP driver released was Version 15.201.1101.0 Rev.A release: January 29, 2016.

    I do not update my driver unless I have a video problem.

    Please keep me informed of the progress of things.

    If you need help, let me know and I will gladly make all that I can to help you.

    Please let me know if that solves the problem by marking this post as "accept as a Solution.
    To simply say thank you, click the Thumbs up below!

    Thank you.

Maybe you are looking for