computer format microtour dc5800: BIOS dc5800 downloads hidden when Windows 7 is selected

When I visit the download page for the format microtour dc5800, the update of the BIOS is visible if I select one operating system other than Windows 7. I'm sure that it makes the download that is difficult for many people to find. I assume that the latest version of the BIOS (1.59) is compatible with Windows 7.

Hello:

I recommend that you Flash the BIOS using the option F10 Flash ROM of system in the BIOS.

Who uses only the files BACK and you don't need to still be under Windows Update the BIOS.

If there is no update of the BIOS listed on the support page, that is who runs the Windows based flash method may not be compatible with W7, and there is a significant risk of causing irreparable damage to the PC.

So yes, the update of the BIOS will work with any system operating, but executed the Windows based Flash utility should be performed only on an operating system supported listed on the download page of the BIOS.

Tags: HP Desktops

Similar Questions

  • Support memory computer format microtour HP 500 b

    Hello

    We are looking to add some memory to a 'Computer format microtour HP 500 b' system, I replaced it s current 2 GB stick with a 4 GB one (Kingston brand, @1333 MHz) but it boot wouln´t upward.

    In this forum I just found this link

    http://h18004.www1.HP.com/products/QuickSpecs/13724_na/13724_na.html#memory

    This means that, while he supports up to 4 GB, it only does in a 2 + 2 mode and not a single module 4 GB?

    I guess this is the model the baord doesn´t have any model printed that I could find.

    I'm going by what I could find based on a report of CPU - ID.

    Chipset

    Northbridge Intel G41 Rev A3

    Southbridge Intel 82801GB (ICH7/R) Rev A1

    Type of DDR3 memory

    Memory size 2048 MB

    Simple strings

    Frequency memory 400,0 MHz (1:2)

    DMI BIOS

    vendor American Megatrends Inc.

    version 6.07

    day 21/03/2011

    System DMI information

    Manufacturer Hewlett-Packard

    product format microtour HP 500 b

    Unknown version

    series[personal information deleted]

    UUID [personal information]

    DMI baseboard FOXCONN provider

    model 2A8C

    Revision 1.1

    Serial unknown

    With a standard business dekstop, you're a little linimted in the improvement of memory. You are right. 2 x 2 GB modules will work, but a 4 GB is very likely to start.

    As seen on this webpage to Crucial2 x 2 GB is recommended upgrade.

    Best regards
    ERICO

  • GP Compaq 6005 Pro format microtour: Reinstall a computer format microtour HP Compaq 6005 Pro

    Hello

    I want to install Windows 7 on several Compaq 6005 Pro format microtour (VN797ET).

    I have product keys Windows 7 Pro to the labels on the PC, it also says OS: Win 7 to XP Pro.

    But the keys to Windows 7 should work for Windows 7 Pro?

    How can I get a W7.iso that runs on the PC. I tried the Microsoft Download page:

    http://www.Microsoft.com/en-us/software-recovery

    When I enter they key I get the following error;

    "The product key you have entered seems to be for the software that came preinstalled on a device. Contact the manufacturer of the software device for recovery options. »

    Can I download a HP image somewhere? These keys function with a generic W7 iso (sp1)?

    Hello:

    You will need to order a set of HP for your PC recovery media.

    If you live in the USA/Canada, call this number... 1-800-334-5144

    If you do not, I have this old list of numbers of support by country.  I don't know if all the phone numbers are more valid.

    http://h50146.www5.HP.com/lib/doc/manual/desktop/business_desktops/6005us_332630_007.PDF

    Have the serial number of one of them handy to give to the customer service rep.

  • Dell XPS 8700 - failure of the keyboard when the bios boot (but not when Windows is loaded)

    My Dell XPS 8700 has 10 Windows and a Logitech Keyboard wireless, connected by USB. The keyboard works absolutely fine when Windows has loaded. I have the latest version of the bios, A11.

    However, when the computer is turned on and starts the bios start, it displays 'Keyboard Failure' on the screen for about half a second. When I try to go into the bios setup by pressing "F2" at the counter (I keep typing "F2" from the moment when I press the power button on the computer), there is no answer. The "keyboard failure" and inability to enter the bios setup seems to happen if I do a cold immediately after a stop start, a cold start after the computer is turned off for an extended period or a reboot.

    I tried to connect the wired keyboard original Dell one of the USB ports on the front of the unit (without disconnecting the wireless keyboard) with the same problem at the start of the bios.

    I encountered this problem on versions of bios A11 both A03. I know that in the past, although I don't remember when - I was able to enter the bios setup by pressing "F2".

    Any thoughts on how to solve this problem?

    You can try and reset the CMOS. It will return your settings to factory settings, but not the version. Usually, this erases these problems because CMOS stores data editable such as your wireless keyboard settings. BIOS stores the information about the basic material that is unchangable as your keyboard usb, mouse and other essential equipment. If you notice, when you just plugin any keyboard and mouse, its recognized at startup. Your needs software to run wireless device and that is stored in the CMOS.

    So once reset you the CMOS, you may need to then install the wireless software.

    Good luck.

  • computer format microtour 3515 PRO ethernet driver

    Hello, I'm trying to install all drivers Ethernet of my model, but nothing works.

    Where can I find an Ethernet driver?

    I post the hardware ID:

    PCI\VEN_1969 & DEV_1091 & SUBSYS_2AE0103C & REV_08

    Thank you!

    This is the page HP Support Center - Microtour HP Pro 3515 - drivers, Software & Firmware for your computer. Please download and install the driver card NETWORK Atheros for Windows 8. For Windows 7, you can try sp56899.exe HP or Driver Atheros Ethernet - HP sp57599.exe

    If you have any other questions, feel free to ask.

    Please click the White Star of KUDOS to show your appreciation

  • Computer format microtour 3015: Format microtour - downgraded to XP, but now want Windows 7 as licensee

    I bought a desktop computer with Windows 7 Pro OA - downgraded to XP Pro. I now want to use the Windows 7 operating system, but I have no media. I can't download the ISO from Microsoft over the license key does not, as it was preinstalled.

    I have not an option to recover to Win7, only for XP, please can someone send me 7 Media? or direct me to the correct download an ISO? Thank you.

    had a chat on-line with the help of HP Media is on the way, thanks

  • computer format microtour dx2250: controller Bus SM dx2250

    I can't find the drivers for SM Bus controller

    You are the very welcome.

    I zipped and attached the file you need below.

    Download and uncompress the file in its folder.

    Click on the INFSETUP file to install the driver.

  • Failure of memory computer format microtour HP Compaq dc5700

    My computer as shown above has the 5 beeps and 5 red LED flashes of light from the memory, indicating that it is the failure of memory. Is it possible to reset the memory locations without opening my Tower? If theres no alternative solutions, it would be very useful. Thank you!

    You must open the tower and reinstall the RAM chips, there is no adjustment.  If it happens again, your ram may be defective.

  • Computer format microtour gen8: Microtower Gen8 deleted folder

    Hi I deleted a very important folder gen8 microtour HP, is possible to restore the date where he went? I have nothing in the trash of my pc...

    Hello

    One possible option is to try the following.

    Click the Start Menu, click your username at the top right.

    Make a right click on the folder was originally included in the document, and then select Properties.  Click on the "Previous Versions" tab and give it time to load (this can take a few minutes).  If you get a list of the previous versions, left-click one of the mentions just to highlight and open - if you see your listed file, copy it to somewhere safe.  If no file is listed, try to open another entrance.

    Kind regards

    DP - K

  • Computer format microtour DC5750 AMD ATHLON 64 x gives 9 beeps and 2 beeps.

    my computer turns off directly when executing after that 10 minutes, which gives 2 beeps with red led flashing once a second, with a gap of two second.and with beeps beeps stop after the 5th time but led will Flash on

    If I try to restart it by disconnecting it and put back:

    After 30 seconds: she gives 9 beeps with led light flashes in the same way

    After 5 min: it turns on and works fine. but does more than 10 to 15 minutes.

    I had over heating problem that is solved now

    Hello:

    Please read annex a starting on page 56 of the Troublehooting manual on the link below, the list of beep codes, possible causes and recommended troubleshooting steps.

    http://h20565.www2.hp.com/portal/site/hpsc/template.BINARYPORTLET/public/kb/docDisplay/resource.process/?spf_p.tpst=kbDocDisplay_ws_BI&spf_p.rid_kbDocDisplay=docDisplayResURL&javax.portlet.begCacheTok=com.vignette.cachetoken&spf_p.rst_kbDocDisplay=wsrp-resourceState%3DdocId%253Demr_na-c00765931-4%257CdocLocale%253Den_US&javax.portlet.endCacheTok=com.vignette.cachetoken

  • I have a computer format Microtour HP 500b and it says memory of 4 MB max.

    I want to put in more memory.  Can I put the bios or something so I can install more memory.  I updated the bios to 6.05... I have windows professional 64-bit.  Any help is appreciated.

    Hi atti2dok,

    It seems that your chipset only supports 4 GB of RAM.  There is not any type of software or BIOS updates that would increase this limit.

    Here is a link with some info on your system memory:

    http://h18004.www1.HP.com/products/QuickSpecs/13724_na/13724_na.html#memory

    Let me know if you have any other questions!

  • Computer format Microtour HP Pro 3010: Hp Support Assistant and LAN with Proxy authentication

    Dear friends,

    I would only know if and how I can 'use' Hp Support Assistant in my office desktop pc, because my desktop pc itself works in the breast of a LAN with proxy authentication.

    Thank you, Paolo ([Personal Information Removed)

    Hello

    Welcome to the HP Support forum!

    Yes, you can use it as long as the desktop PC is HP branded.

  • Computer format microtour 3400: PCI Simple Communications controller 3400 format microtour FRI ID = 8086 (Intel) DEV ID = 1C3A

    I scoured everywhere for this driver. I know it's a driver of Intel Management Interface, but that the site does not work. Can someone point me in the right direction? I installed tons of drivers over the years and have a lot of experience, looking for unknown drivers, but when manufacturers doen't website work drivers, it's when I hit the wall.

    I found this information by clicking on properties - hardware ID and will pcidatebase find Fri (even if I memorized intel as 8086) and looking for a dev id. Any help would be greatly appreciated!

    Hello:

    See if it works...

    This package provides the original for the solutions Intel Management Engine Interface driver in the supported models that are running a supported operating system.

    File name: sp57372.exe

  • Updating BIOS for motherboard Μatx-IG41-H on format Microtour Compaq 500 b

    OK, here's my problem;

    I just bought a 4GB Ram DDR3 1333 Mhz Kingston for my computer format Microtour Compaq 500 b. But when I try to connect this new RAM for my motherboard, pc gives error of RAM and that it does not open.

    It works well with other computers.

    Support members told me to update my Bios, but I can't find any update file which is updated. The only thing I could find is the following; http://h20000.www2.HP.com/bizsupport/TechSupport/SoftwareDescription.jsp?lang=en & CC = HR & prodTypeId = 12...

    I hope someone can help me with this.

    Thanks in advance...

    Here is the HP Compaq Business Desktop ROMPaq Firmware (ROM family CPT006) aka BIOS downloads for HP/Compaq 500 b/510 MT Professional computer. These BIOS/firmware updates do not appear to address any memory related questions. HP/Compaq 5xxB MT maintenance & Service Guide;

    Memory:
    The computer comes with synchronous dynamic RAM 3 double rate
    (DDR3-SDRAM) dual inline memory modules (DIMMS).
    DIMM DDR3-SDRAM:
    Media memory on the system card can be filled with up to two industry standards
    DIMMs. These media memory are filled with at least one DIMM preinstalled. To achieve the
    maximum memory support, that you can fill out the card system with up to 4 GB memory
    configured in a high-performance dual channel mode.
    For the proper functioning of the system, the DDR3-SDRAM DIMM modules must be:
    240 industry standard pins
    unbuffered PC3 - 10600 1333 MHz compatible
    DIMM DDR3-SDRAM 1.5 volts
    DIMM DDR3-SDRAM strips must also:
    support the latency CASE 9 DDR3 1333 Mhz (9-9-9 calendar)
    contain the compulsory particulars of the JEDEC SPD
    In addition, the computer supports:
    512Mbit, 1Gbit and 2 GB non - ECC memory technology
    front and double-sided DIMMs
    DIMMs built with devices DDR x 8 and x 16; Built with x 4 SDRAM DIMMs are not
    support
    NOTE: The system will not work properly if you install unsupported DIMM modules.

    The total State "up to 4 GB' plug... which is in both slots, therefore each slot can only use a 2 GB DIMM.

  • Format microtour Dx6100 display problems.

    Hello

    I have a computer format microtour dx6100.

    I've upgraded to windows 7 64 bit and everything works fine except that I have problems with the display.

    The VGA output will not go in widecreen? I can't find a driver for this problem.

    I also tried to install an Ati x300se video card pci-e 128 MB that I thought it was compatible but it seems other people have got it to work in vista compatibility mode but I have no luck with it it keeps crashing when trying to install.

    Does anyone have any suggestions of what I can try?

    Regards, Alex.

    Hey, Alex:

    Have you tried this driver for the x 300?

    http://support.AMD.com/en-us/download/desktop/legacy?product=Legacy1&OS=Windows 7-64

Maybe you are looking for

  • Mail no longer works correctly

    Hello, my e-mail no longer works correctly. [Air MacBook OS X El Capitan 10.11.5] It would not accept my password of account for a reason, so I removed my server provider and then he added through accounts. It worked, but mail is now different, and e

  • Satellite click Mini L9W - B - lost after update Win 10 software

    Hello. I upgraded my Windows 10 click Mini as soon as I got it yesterday. Everything seemed fine until I restarted and it would not start, there was a problem with the drive of the declaration. Finally, after having used the keylogger to unlock the d

  • Why do I have a folder of FireFox in the folder My Music (Win 7 64 bit)

    I do not remember doing something different or weird when I was installing FireFox to my Win 7 laptop but when I go in the folder My Music/Music Library there is a record of Fire Fox with links to start firefox and safe mode of Fire Fox. But I don't

  • Hinge on Satellite M30 is loose

    The right hinge on my 30 M is to lose. I tried to disassemble the keyboard without success, what to do?

  • Door to the water-resistant case

    I was wondering if I can get or replacement for the subwoofer doors sealed on the FDR X1000V?