Computer laptop battery "in charge" but stuck at 0%

Hello

I have a G6-1b79ca Pavilion and the battery stopped charging.

Windows show "Plugged in, load" and level to remain at 0%. Forever.

Of course it is now completely empty.

If I remove the CC of the computer plug, turn it off immediately.

Here's what I did so far, more or less in that order:

1. replace the battery (recommended by the logon page BIOS...)

2 tried this popular patch:

Stop-> remove battery and power cord-> hold down the button "POWER" 30 sec-> power supply DC-> Boot->-> battery-> uninstall Microsoft ACPI-Complient control method battery -> Shutdown-> put the battery in the Device Manager (cannot start on him alone because it does not... but maybe that might help)-> start the computer

3. updated all the drivers and reinstalled all the HP utility (got the Intel drivers on the Intel site)

4. I updated the BIOS with the latest version and reset to default settings

5 tested the power supply with a multimeter (Psu unloaded, sleeve ground referenced outside it read 19.8V = internal plug, 18V centering PIN)

6 replace the motherboard (which has already been replaced)

7. replace the power supply

8 reinstalled Windows

9 weld the power directly to the motherboard adapter in order to bypass the connections all contacts (cut the CC Plug and soldered the bare wires directly on the pcb)

The utility HP BIOS (F2 on startup) told me that the new battery fails the test and must be replaced. Awesome.

The battery in the utility test assistant (run in Windows) HP tells me that the battery is OK, but would need to be loaded (Seriously? It becomes funny...)

So basically the material is new.

Utility Windows/HP tells me that the battery is OK, but the BIOS utility will tell me to replace it.

What the hell is happening?

The material is supposed to be (entirely replaced) A1 and windows were completely reinstalled.

Any suggestion? My beginning of sanity to fade...

On a side note, here is the situation that I hope not occurred:

1. the original battery has failed

2. he burned the motherboard charging circuit

3. I replaced the battery then damaged mother burned load circuit card

4. I finally replaced the motherboard that was damaged by the new battery, which was damaged by the previous motherboard, which was damaged by the original battery...

5 return to square one, hundreds of $ less and a lot of time to lose...

I can't buy ANOTHER motherboard/battery combo without going crazy...

Thanks for any help!

HE IS ALIVE! Lolll!

The problem is the new battery, I don't know why, but it was completely empty and never had to charge.

I ask the seller to replace and load a new a bit so I was able to start on battery only.

I removed the power supply and the battery, which held the POWER button / 30 sec and started on the battery alone.

Once in Windows I pluged the charger and now it is fully charged!

Looks like the key here is to be able to start on battery alone. one thing I could never reach while struggling with that drained.

This thread of hope help someone solve battery problems, because there are MANY possible solutions.

Thanks to those who have taken their time to help!

Tags: Notebooks

Similar Questions

  • PC laptop battery not charging but laptop works with the power adapter... which is wrong

    My power supply battery icon States attached but do not load, why

    Hello

    Download and run the test utility of battery pack available on the next page and see if it reports any problems with your battery.

    http://h20239.www2.HP.com/TechCenter/battery/battery_ts.htm

    Kind regards

    DP - K

  • Laptop battery only charges to 79%. Think I've changed the settings earlier to save the battery of thea, but now want to 100% load again.

    My laptop battery is ok, but still only charge up to 79%. And stop there. What should do? I changed the settings as soon as possible to save the battery, but now wants to load 100% again. I can't find where to change them back.

    If you start in System Setup (BIOS) - before any loading of the operating system - and look at the section health and charge battery... What percentage watch battery is charged it?  What status?  If leave you it in the BIOS and let it load this way - it's 100% top?  If so - what happens when you start in Windows?

    (Trying to confirm this, it is an error within the OS and not a hardware problem).

  • Laptop battery not charging not (630 HP)

    Hi all

    Laptop battery not charging. When I plugged on current alternative, it shows plugged in, not charging but acute battery

    load. I change the battery but problem not solved. Then I replaced the power supply but problem not solved.

    Advice me please.

    Cell phone: HP630

    error: no current charging

    OS: WIN 07

    Thank you

    Migas

    Go in Device Manager. Find the battery device. Click the triangle next to the battery to decompress. Left click on the device of the compatible battery Microsoft ACPI control method, then right-click and choose uninstall. Once he uninstalled it can install on its own, but if not only, right-click on any device and select search the hardware changes. The operating system must install a new copy of the device of the compatible battery Microsoft ACPI control method.

  • my computer laptop bluetooth was working but suddenly it stopped and I don't know why... How can I make it work again please!

    Original title: quick help please :/

    my computer laptop bluetooth was working but suddenly it stopped and I don't know why... How can I make it work again please!

    Hello

    Hardware devices not detected or does not work - a Mr Fixit
    http://support.Microsoft.com/GP/hardware_device_problems

    Add a BlueTooth device to your computer
    http://Windows.Microsoft.com/en-us/Windows7/add-a-Bluetooth-enabled-device-to-your-computer

    Set up a Bluetooth compatible device
    http://Windows.Microsoft.com/en-us/Windows-Vista/set-up-a-Bluetooth-enabled-device

    The problems with Bluetooth devices
    http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-problems-with-Bluetooth-enabled-devices

    How to set up a Bluetooth connection
    http://www.vista4beginners.com/how-to-setup-a-Bluetooth-connection

    The Bluetooth item in Control Panel on a Windows Vista SP2 computer does not
    as expected when you click on the element - for Windows 7 this check manually
    http://support.Microsoft.com/kb/960531/en-us

    If you need drivers try the support site for the manufacturer of your system and/or the site of the manufacturer of the real device.

    BluetoothView is a small utility that runs in the background and monitor the activity of Bluetooth technology
    devices around you. For each detected Bluetooth device, it displays the following information:
    The device name, address Bluetooth, Major Device Type, minor device Type, first detection time,
    Last detection time and more. BluetoothView can also warn when a new Bluetooth device
    is detected, by displaying a balloon in your bar tasks or playing a little beep. -FREE
    http://www.NirSoft.NET/utils/bluetooth_viewer.html

    BluetoothCL is a small console application that transforms all differential of bluetooth devices detected in
    the standard output. For each Bluetooth device, the following information is displayed: MAC
    Address, name, Major Device Type, minor device Type and possibly the name of the company of
    the device (if the external file of MAC addresses - oui.txt is provided) - FREE
    http://www.NirSoft.NET/utils/bluetoothcl.html

    BluetoothLogView is a small utility that monitors the activity of Bluetooth devices around you,
    and shows a log of Bluetooth devices in the main window. Each time that a new Bluetooth
    device coming to your area and when the unit comes out of your area, a new journal line is added with
    the following information: device name, time of the event, address, Type of event ("peripheral
    Arrival' or 'Device left'), Type of aircraft and the company that created the device. BluetoothLog-
    View you can also specify a description for each device (according to its MAC address)
    that appears in the column "Description". -FREE
    http://www.NirSoft.NET/utils/bluetooth_log_view.html

    ---------------------------------------------------------------------

    Change settings for a Bluetooth compatible device
    http://Windows.Microsoft.com/en-us/Windows7/change-settings-for-a-Bluetooth-enabled-device

    Add a Bluetooth device to your computer
    http://Windows.Microsoft.com/en-us/Windows7/add-a-Bluetooth-enabled-device-to-your-computer

    Add a Bluetooth device or other wireless or network device: frequently asked questions
    http://Windows.Microsoft.com/en-us/Windows7/add-a-Bluetooth-or-other-wireless-or-network-device-frequently-asked-questions

    ---------------------------------------------------------------------

    More information of possible interest to some:

    What is a Bluetooth personal area network (PAN) network?
    http://Windows.Microsoft.com/en-us/Windows-Vista/what-is-a-Bluetooth-personal-area-network-Pan

    Connect to a Bluetooth personal area network (PAN) network
    http://Windows.Microsoft.com/en-us/Windows-Vista/connect-to-a-Bluetooth-personal-area-network-Pan

    I hope this helps.

    Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle=""><- mark="" twain="" said="" it="">

  • PC laptop battery not charging

    Responsible for issues

    When I try to load my computer, the battery light does not turn on and will not charge. I've already replaced the battery and the new adapter. He still will not load. Any ideas?

    Hello

    1. which version of the windows operating system is installed in the computer?

    2. What is the brand and model of the computer?

    Method 1:

    I suggest you run the Microsoft fixit tool and check.

    The problems of power consumption and extend laptop battery life

    http://support.Microsoft.com/mats/windows_battery_power_settings/en-us

    Method 2:

    If your operating system is windows 7, I suggest you to see the links and check.

    What is the precise the battery meter?

    http://Windows.Microsoft.com/en-us/Windows7/how-accurate-is-the-battery-meter

    Solutions to common battery problems

    http://Windows.Microsoft.com/en-us/Windows7/solutions-to-common-battery-problems

    Battery saver

    http://Windows.Microsoft.com/en-us/Windows7/conserving-battery-power

    See also:

    Battery meter: frequently asked questions

    http://Windows.Microsoft.com/en-us/Windows7/battery-meter-frequently-asked-questions

    I also suggest you to communicate with the manufacture of battery and check.

  • my laptop battery only charges never beyond 28%

    the battery on my acer aspire 5741 does never charge beyond 28%

    Hello

    References to Vista also apply to Windows 7.

    Check with support from the manufacturer of their books online and the drivers and their forums system
    (as applicable) for known issues. Some manufacturer issued BIOS and other updates to help the battery
    problems.

    Acer - USA - Service and Support - drivers
    http://us.Acer.com/AC/en/us/content/support

    Acer - worldwide
    http://www.Acer.com/worldwide/selection.html

    ================================================================

    Follow these steps to remove corruption and missing/damaged file system repair or replacement.

    Run DiskCleanup - start - all programs - Accessories - System Tools - Disk Cleanup

    Start - type in the search box - find command top - RIGHT CLICK – RUN AS ADMIN

    sfc/scannow

    How to fix the system files of Windows 7 with the System File Checker
    http://www.SevenForums.com/tutorials/1538-SFC-SCANNOW-Command-System-File-Checker.html

    Then run checkdisk (chkdsk).

    How to run check disk in Windows 7
    http://www.SevenForums.com/tutorials/433-disk-check.html

    =================================================================

    Other information that might help:

    Control Panel control - plan change Options - power plans - power - advanced settings
    Parameters for the drainage and the use of parameters (this is how much to use and not how much or how)
    long to load).

    In fact, what causes a lot of wear on a battery empties it too low on several occasions. With today
    systems overload are not a problem.

    Here are some tips to help and troubleshoot battery issues.

    Old battery? Unplug the power to the computer - remove the battery and clean the contacts with a pencil
    eraser (do not use this, if your battery is fine slots - just clean up the edges of the knife which fit in)
    them and be careful). Batteries are old, or it could be a problem with the computer.
    Check with the support of the machine system, and many of them have online forums.

    New Lithium-Ion type battery usually last longer if you do not unload their less than 30%
    However on a laptop that not extend their life a lot. Best is to use the a/c adapter
    When this is possible.

    I use the free version of BatteryBar to monitor my battery. Click on the green button on the
    Yellow box on the right side of the page to download the latest stable version.

    BatteryBar - free version available
    http://osirisdevelopment.com/BatteryBar/index.html

    Another good program

    Vista battery saver - free
    http://www.codeplex.com/vistabattery

    Problems with the lives of its use and the battery of power - Mr Fixit
    http://support.Microsoft.com/GP/windows_battery_power_settings

    You can also check with the manufacturer of system and forums that many use their own
    proprietary software to monitor the battery and they could be known problems with your battery.

    ============================================================

    Taking care of your laptop battery
    http://Windows.Microsoft.com/en-us/Windows7/taking-care-of-your-laptop-battery

    Battery meter: frequently asked questions
    http://Windows.Microsoft.com/en-us/Windows7/battery-meter-frequently-asked-questions

    Battery saver
    http://Windows.Microsoft.com/en-us/Windows7/conserving-battery-power

    Solutions to common battery problems
    http://Windows.Microsoft.com/en-us/Windows7/solutions-to-common-battery-problems

    What is the precise the battery meter?
    http://Windows.Microsoft.com/en-us/Windows7/how-accurate-is-the-battery-meter

    ============================================================

    Try this - to make a Restore Point

    How to create a System Restore Point in Windows 7
    http://www.SevenForums.com/tutorials/697-system-restore-point-create.html

    How to do a system restore in Windows 7
    http://www.SevenForums.com/tutorials/700-system-restore.html

    Then Control Panel - Manager of devices - Batteries - Double click on each item - drivers - tab
    Update the drivers (which can do nothing) - then do a right click and UNINSTALL each - RESTART
    who will update the driver stacks.

    Problems with the lives of its use and the battery of power - Mr Fixit
    http://support.Microsoft.com/GP/windows_battery_power_settings

    I hope this helps.

    Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle="" -="" mark="" twain="" said="" it="">

  • My acer PC laptop battery not charging

    My acer laptop will not charge

    Hello

    How to check and repair a laptop computer death or netbook
    http://www.YouTube.com/watch?v=VCNQthuubR0&feature=related

    Check with support from the manufacturer of their books online and the drivers and their forums system
    (as applicable) for known issues. Some manufacturer issued BIOS and other updates to help the battery
    problems.

    Acer - USA - Service and Support - drivers
    http://us.Acer.com/AC/en/us/content/support

    Acer - worldwide
    http://www.Acer.com/worldwide/selection.html

    -----------------------------------------------------

    Control Panel control - plan change Options - power plans - power - advanced settings
    Parameters for the drainage and the use of parameters (this is how much to use and not how much or how)
    long to load).

    In fact, what causes a lot of wear on a battery empties it too low on several occasions. With today
    systems overload are not a problem.

    Here are some tips to help and troubleshoot battery issues.

    Old battery? Unplug the power to the computer - remove the battery and clean the contacts with a pencil
    eraser (do not use this, if your battery is fine slots - just clean up the edges of the knife which fit in)
    them and be careful). Batteries are old, or it could be a problem with the computer.
    Check with the support of the machine system, and many of them have on line forums.

    New Lithium-Ion type battery usually last longer if you do not unload then less than 30%
    However on a laptop that not extend their life a lot. Best is to use the a/c adapter
    When this is possible.

    I use the free version of BatteryBar to monitor my battery. Click on the green button on the
    Yellow box on the right side of the page to download the latest stable version.

    BatteryBar - free version available
    http://osirisdevelopment.com/BatteryBar/index.html

    Another good program

    Vista battery saver - free
    http://www.codeplex.com/vistabattery

    Problems with the lives of its use and the battery of power - Mr Fixit
    http://support.Microsoft.com/GP/windows_battery_power_settings

    You can also check with the manufacturer of system and forums that many use their own
    proprietary software to monitor the battery and they could be known problems with your battery.

    ============================================================

    Try this - to make a Restore Point

    How to create a Vista System Restore Point
    http://www.Vistax64.com/tutorials/76332-system-restore-point-create.html

    How to make a Vista system restore
    http://www.Vistax64.com/tutorials/76905-System-Restore-how.html

    Then Control Panel - Manager of devices - Batteries - Double click on each item - drivers - tab
    Update the drivers (which can do nothing) - then do a right click and UNINSTALL each.
    RESTART which will update the driver stacks.

    Problems with the lives of its use and the battery of power - Mr Fixit
    http://support.Microsoft.com/GP/windows_battery_power_settings

    I hope this helps.

    Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle=""><- mark="" twain="" said="" it="">

  • HP laptop G3 255: nine 255 G3 laptop battery not charging...

    I'll put a G3 255 for a friend and I noticed that the battery won't charge. Indeed, the battery, unlike all the portable precedents that I put in place, had a load zero on the box. From memory, with all previous laptops, new batteries held at least some charges.

    Icon in the tray of food says "0% available (plugged in, load)" while the balance of the battery in the utility HP Support Assistant says "the battery works fine but has not been charged recently.

    Just to be clear, if I unplug the machine turns off instantly and if I try to turn it on without the power cord plugged in, absolutely nothing happens. Certainly feels as if the battery has no charge be and takes no fees either.

    Of course that one day, the machine is under warranty, but I just wanted to get opinions on the question of whether the battery or laptop will be the problem. Only, I discovered the flaw after hours to transfer all the stuff from his old address so prefer to avoid it even once! I hope that HP sends out (or swap) a new battery.

    Anyone has similar experiences with batteries not charging or maintain any load and with HP response?

    Your description describes one main battery failed.

    The main battery and the mains adapter are covered under warranty for any cost of replacement devices guarantee.

    I ask that your question is raised.

  • HP ENVY m4-1015dx Notebook PC: hp envy m4 battery not charging but fresh when the laptop is turned off

    Hello!

    I was with my hp envy m4 core i7 for quite a while now... recently, I formatted and installed windows 8.1 64-bit installed. I decided to download some drivers from the hp site and I realized I needed to provide my model of laptop model number I could not remember so I decided to remove the battery while the computer is still connected to the power for the number, then I went back to the battery. the latter, I realized that the cell had not accused beyond of 7%, which was the level of support, until I removed the battery and when I checked the charge level, it indicated that it was plugged in but does not support. When I tried to repeat the entire process as well as close the laptop, remove the battery and turning it again nothing work and completely refusing to charge for its on.when I decided to turn off completely and then it was off it perfectly complete accused 100% operating battery estimated more than six hours of charge time, guys help me to understand what might have developed and what will be the best solution.

    Hi @Phanz,

    Thank you for your inquiry.

    I entered which you have tried to download the driver on the HP website for your laptop but realized you need the model number.  You have removed the battery while the laptop is running.  Now when you reinstall the battery, it shows that it is connected but does not charge and continues to 7%.   You have repeated the process and close Notepad and removed and reinstalled battery, but there was no change. If you turn off it charges the battery to 100%.

    You did all your Windows updates?

    Have you tried the troubleshooter in Windows?

    First of all, I would like to try a Windows restore to before remove you the battery.

    HP computers - using the Microsoft System Restore (Windows 8)

    If restore doesn't work or is not possible, you could try a Refresh Your PC to solve problems (Windows 8).

    Then you can try the following steps.

    HP laptops - test and calibrate the battery (Windows 8)

    The battery method compatible ACPI Microsoft control is basically the driver that communicates between the computer and the battery. There is a chance that it became corrupt and bad reads the battery level.

    Step 1. Go to the Device Manager
    Step 2. Select the stacks
    Step 3. Click with the right button on the "Microsoft compatible battery ACPI Control method" which is in the list
    Step 4. Click on uninstall
    Step 5. At the command prompt, put a checkmark in the box to remove the current driver
    Step 6. Shut down the computer

    Step 7: Remove the battery for a minute and then put new

    When the computer returns to the top it should automatically find the driver.

    Step 8. Go to the Device Manager
    Step 9. Select the stacks
    Step 10. Click with the right button on the "Microsoft compatible battery ACPI Control method" which is in the list
    Step 11. Click "automatically search for an updated driver.

    Do the same thing with embedded controller compatible ACPI Microsoft.

    Last option is to reinstall your Windows 8.1 Pro.

    Good luck!

  • Computer laptop G62 lights fan but without screen or full charge

    My G62-a03SA does not start correctly, when I press the button to power the fan starts strong and the power and light of the Internet light, but seeing Internet remains orange turn off turning white which is usually done on start up. Then the fan stops as if she has not turned on and after 10 seconds turns very quietly running.

    The lights remain the same and the screen never lights just stays black.

    Help?

    Hello CPlume64. I understand that you are experiencing some problems getting your computer from starting properly.

    Have you noticed if the SHIFT CAPSLOCK or Numlock lights blink? If none of the two flashes then it indicate a specific problem. Thus, if one blinks then how many times it blinks?

    To start working on your issue I suggest that perform you a hard reset. This forces everything to be reset and can solve a wide range of issues. Try the following.

    1. Turn off the laptop.
    2. Remove the battery and AC power.
    3. Press and hold the power button for 15-20 seconds, three times.
    4. Replace the battery and AC power.
    5. Try to start Notepad and post the result.

    I'll keep an eye out for the results of this reset. I wish you a nice day!

  • HP G61 - 448CA computer laptop battery low quality.

    Support staff HP and my fellow forum users.

    I own a HP G61 model 448 portable computer CA and have used it with more or less good efficiency over the past four years. Unfortunately but the quality of my battery has dropped considerably in recent months leading to a battery error message every time I turn it on. I also noticed that the charge runs out very quickly when it is not plugged into the minutes rather than an hour or two. I could not find a way to save my battery and repair its effectiveness or find a suitable replacement on the HP online store. I tried to call their support line, but they seem to be busy every time. Any help pointing me to a solution or a way to buy a spare battery that will focus on my laptop for a reasonable price would be greatly appreciated.

    4 years is a battery to last long.

    eBay has new batteries original for the good price too long you can expect for China shipping:

    http://www.eBay.com/ITM/genuine-original-HP-Presario-battery-G61-400-G61-410SA-G61-420CA-6Cells-47Wh-/260974802987?PT=Laptop_Batteries&hash=item3cc34f782b

    This is one of the United States:

    http://www.eBay.com/ITM/original-battery-for-HP-dv4-dv5-DV6-G50-G60-G61-G70-HSTNN-UB72-EV06-genuine-OEM-/271326231939?PT=Laptop_Batteries&hash=item3f2c4dbd83

    If it's 'the Answer' please click on 'Accept as Solution' to help others find it.

  • Laptop battery not charging?

    I use a HP b4p41pa with Microsoft windows 7 home 64-bit

    The problem I have is that I noticed that I had not used the charge for a while cable so I checked my percentage of left to find I got 86% with computer reporting I got 116 hours and left 32mins. Of course, that couldn't be good if I put the charger and after 10 minutes, and then verified the number once again, still 86%.

    I took out the charger and it still says 86%. All the way up to what it off no charge at all. I put the left rear feeder lunch and in. Since then, charger in for 30 minutes or outside for 4-5 minutes, it says I have 5% left and until his remarks goes.

    In all honesty I don't know if it's the battery, charger, or if the computer falsely reports the amount of fees because I used it for these 4-5 minutes without it cutting.

    I ridiculed my wife to purchase a Toshiba who gave his problems after 2 months, but I got this HP for the grand total of 4 days. He can't have these problems already surely?

    Thanks for any help in advance and I hope I've provided enough information.

    Hello

    Go to Device Manager. (type device in the search of all manager programs and files box and press enter)

    Click the triangle next to the battery unit to decompress.

    Right-click on the devices that are revealed. One at a time, select uninstall for each of the following devices.  (Microsoft and compatible ACPI Microsoft control method battery AC adapter)

    Once you have uninstalled them, then do a right-click any device and select check for material changes.

    The Windows 7 operating system will reinstall fresh devices copies that you just uninstall.

    Restart your laptop and check to see how the loading goes.

    Now open HP Support Assistant --> Troubleshooting --> electrical, thermal and mechanical. In the power tab click on check the battery...  If you don't get a pass or OK on the battery check, then contact HP Total Care warranty service

    Post here your results positive or negative.

  • Satellite A60 - laptop battery not charge/work

    Hello

    My stop laptop when you use the battery power. It will not re-start until I plugged in to the power supply. Every time I disconnected power laptop would shutdown. laptop does not work on batteries, no lights are working.
    When it is plugged seeing orange lights. Battery remains 90% fresh even after hours on departure av! I suggest that I can't use the battery power and the battery won't charge.
    Only a new battery in a month and has worked well up until now.

    I tried toshiba control energy saver but made no difference.

    I can't say with certainty if this happens because of the battery or something. In my opinion, it can be either battery or electronic power supply.
    Satellite A60's old laptop and everything is possible.

    Pre-installed software doesn t have a any influence on this. Toshiba power saver is preinstalled to consumption, Manager, with other words to help reduce battery power consumption and longer battery.

  • Battery fully charged but Equium M50 starts

    Hello

    I'm looking for some help with a battery problem.

    A couple of days, I was using my pc and is going to move in the kitchen, but as soon as I unplugged the AC cable unplug the laptop has been cut.

    I checked and it says the battery is 100% / full power.

    This happened to someone else or someone know what is causing this / how to fix it?

    Thank you.

    Hello

    First of all, if the laptop is connected to the power adapter then it should run and it lights without the use of the battery!

    Second, if the battery is old it might happen that he was running only for a few minutes even it s fully charged.

    Happens to me too my battery is about 6 years old and he says that a single minute. Then it s empty.

    I know that I have to replace it, but the battery is not very important for me because my old laptop is still on the table and still connected to the power adapter.
    If I can live with the bad battery

Maybe you are looking for