Computer runs continuously check disk and automatically goes into power saving mode.

Similar Questions

• Monitor goes into power saving mode

  I have a client with a 660 Inspiron, and while working on this subject, the monitor goes into power saving mode.  Using another monitor has the same results. Now, here's the catch, the motherboard has been replaced with the same results so Dell sent his computer to another. After that set up the new computer things seemed to be OK for about 30 minutes, and then the new computer came into power saving mode. Again with another monitor to get the same results. Any thoughts?

  Hi TimMcKinney,

  Welcome to the community.

  Please let us know the version of windows and the video card installed on the system. Please check the system with a different video cable as well.

  Once the system goes into power saving mode please let us know the color of the leds on the tower.

  If you have additional questions, feel free to contact us.

  Thanks and greetings
  Sandeep P
  #iworkfordell

• Portege M400: screen power save after going into power saving mode

  When my monitor goes into power saving mode sometimes, it is not be able to save, I solved this stopping mode energy saving, but it means that I have to drain the battery much faster help!

  I'm sure it's just the screen as I can hit the power button and it seems closed, (it crashes out of sleep mode and I only managed to get it to go into hibernation, once with success (he complains that there there not enough wealth, but there a lot 33 GB of free hard disk! that's a lot to store 2 GB of ram) it is really annoying and I have yet) the laptop over a week!

  Is it possible to find a solution or a way to find what is causeing these issues?

  -
  Garthark

  Hi Oliver

  I read your messages carefully and I'm really a bit confused. As far as I know all the tools pre-installed on each unit of Toshiba are tested. Sleep mode and standby extended too and I can't really understand what is happening in your case.

  The problem may be caused by the use of some third-party software of the part. In my opinion, do not do some experiments with non-Toshiba (driver chipset or display) software, because the software is adapted to the architecture of the unit and equipment.

• Monitor Dell Vostro 2705 keeps going into power saving mode

  I have a Dell Vostro 2705. When I turn it on, the screen goes into power saving mode. We tried with a different monitor and it still does not work. I do not see there is a separate video card to replace it. Can it be fixed or is - a new computer?

  Thanks in advance for your advice.

  Judy

  Hello

  Its usually a faulty motherboard. So the only option is to get the Board replaced.

  You can try doing a power cycle and if still doesn't work then a replacement of the Board of Directors.

  Concerning

• My laptop goes into power saving mode after one minute. Someone knows why?

  It's just started happening yesterday. I use a Toshiba laptop and out of nowhere, my PC goes in power saving mode after one minute when ALL my settings for this mode is 30 minutes. Does anyone know how to fix this?

  Hi MattLipkint,

  1. Did you the latest changes on the computer?
  2. When was the last time it was working fine?
  3. You have security software installed on the computer?

  Method 1

  It is possible that some third-party programs installed on the computer is causing the problem.

  I suggest that you put the computer in a clean boot state and check if it helps.

  To help resolve the error and other messages, you can start Windows XP by using a minimal set of drivers and startup programs. This type of boot is known as a "clean boot". A clean boot helps eliminate software conflicts.

  See section to learn more about how to clean boot.

  How to configure Windows XP to start in a "clean boot" State

  http://support.Microsoft.com/kb/310353

  Reset the computer to start as usual

  When you are finished troubleshooting, follow these steps to reset the computer to start as usual:

  (a) click Start, type msconfig in the search box and press ENTER.

  (b) If you are prompted for an administrator password or for confirmation, type your password or click on continue.

  (c) under the general tab, click the Normal startup option, and then click OK.

  (d) when you are prompted to restart the computer, click on restart.

  Method 2

  If the previous step fails then I would suggest that you update the display adapter drivers, basic input/output system (BIOS) and motherboard chipset drivers.

  Important: Change (CMOS) BIOS/complementary metal oxide semiconductor settings can cause serious problems that may prevent your computer from starting properly. Microsoft cannot guarantee that problems resulting from the configuration of the BIOS/CMOS settings can be solved. Changes to settings are at your own risk.

  How to manage devices in Windows XP

  http://support.Microsoft.com/kb/283658

  How to solve the problems of hibernation and standby in Windows XP

  http://support.Microsoft.com/kb/907477

• Monitor goes into power saving mode or restarting PC

  I recently bought a Dell XP 8500 with 7870 AMD and Dell U241M monitor.

  When the computer is turned off for awhile (overnight, for example), the monitor almost always goes into energy saving mode while the PC starts in the AM (I do not see the BIOS/post visuals). If I stop the PC and power cycle a few times (turn on/off the monitor and the PC at the same time) it will generally work after 3-4 tests.

  "Sleep" mode on the PC is turned off.

  If I turn off the PC for the night and leave the monitor to go to sleep, the monitor wakes up fine when I move the mouse the next AM.

  If I turn off the PC overnight and also If turned off the monitor, PC restarts when I turn on the monitor of the AOS .

  If I turn off the PC or the monitor for a few minutes, it will work the next time it starts perfectly. The problems seem to be when he stayed all night.

  I have exchanged monitors and see the same problem with the XPS and another monitor, while the U2412M works fine on another PC.

  I tried DVI - DVI and DisplayPort to DisplayPort Cable with no difference. I tried to plug in a different bar / food. I tried to replace the GPU and checked that GPU power cable connections are tight.

  So, I guess that the problem is in the hardware XPS GPU or PSU and I'm quite surprised it didn't fall Dell quality control (or it has been damaged during transport?).

  Any thoughts? I don't really want a backup and reconfigure a new Tower and thought that I would get away from this kind of problems by going with a Dell.

  Thank you

  Sam

  For those who might wonder what was the end result, Dell has replaced the GPU and now it's fine.

• Computer keeps going into power saving mode

  Hello, I'm fighting with my pc it keeps going on the power saving mode how to stop what I sometimes lose my job

  Original title: URGENT
  Moved from the community involvement Center

  Disable saving energy mode in Windows 10

  1. Click Start
  2. Type power and press ENTER to open it
  3. In Option of power--> the window on the right panel under ' choose or customize a power pan "selected Plan is a balanced.
  4. Then click on change plan settings
  5. 
  6. This will open the Edit plan setting window
  7. To turn off the screen FOREVER in both batteries & Plugged In
  8. Make sure you put the computer to sleep FOREVER in both batteries & Plugged In
  9. 
  10. Then click on save changes
  11. This will save it, and you're done!

  Note:

  1. Battery: It will accordingly when the system is on battery Mode (load is not Plugged)

  2. Plugged in: Will accordingly when the system is Plugged In to the wall (the charger is plugged in)

• Try to stop the XP machine, keeps flashing 'Current Auto adjustment' and goes into power saving mode instead

  Keep them from flashing "setting current auto" and not shut down completely... stay in power saving mode.  What should I do?

  * original title - Dungeon of flashing "auto adjust in progress" help *.

  Hi cindytown,
   
  The "Automatic Setup" dialog box is displayed on a black screen as the monitor is automatically set on the current entry.
   
  Auto setting will not happen if you press the monitor button, while there is no active video input signals, or attached cables.

• My computer keeps going into power saving mode and it is not configured for it... What can I do

  My computer guard shut down in power save mode... I installed everything that has been suggested to correct this, but nothing works

  Read the documentation that accompanies and/or to communicate with the computer manufactures Technical Support.

• Monitor immediately goes into POWER SAVING MODE on startup

  Hello and HELP!

  Just unpacked a Dell Inspiron 530, I bought in January 2009 (long story).

  After all hang up, I turned it on. Monitor shows a brief moment, just a flash, AUTO DETECT (ANALOG INPUT) entering POWER SAVE, then it goes black and nothing that I bring him on.

  This Inspiron came only with a VGA monitor plug. The flat screen has a DVI and VGA and DVI and VGA cables sheets. I connected the VGA cable to the VGA connectors.

  I tried the fixes I found on this site: PC and disconnect the cable VGA pc and monitor, reconnect. Disconnecting power plug from the monitor, plug back. From the start, press the F6 key. Nothing. Nothing. Nothing. He has been guaranteed.

  I noticed when the monitor is not plugged into the pc and I turn it on, it flashes the message AUTO DETECT (ANALOG INPUT) entering POWER SAVING again and stops.

  The cable would be bad? The video card would be bad? The video card could be on the DVI?
  I can't even enter and see the BIOS, blind without visual. The speakers are in the monitor, and no sound is coming from them. Don't know if run even Windows (Vista).

  Any suggestions?

  I pulled the cards memory, slightly rubbed copper with an elastic band, popped them back in and viola, the entrance to the screen the!   Found this tip on the web site of kioskea. Thanks for responding so Sujatha!

  Margoo

• How can I configure my computer to it won't go into power saving mode every 2 min

  How can I configure my computer to it won't go into power saving mode every 2 min

  How can I configure my computer to it won't go into power saving mode every 2 min

  Change the configurations screen saver and hibernation / sleep appropriate for your desires.

• computer freezes and goes to power saving mode

  Several times a day my computer freezes and goes into the power saving mode.

  Hello
   
  1. have you made changes on the computer recently?
  2. do you use a particular application when your computer crashes?
  
  Method 1.
  Check to see if the problem exists in Safe Mode, if the computer works as expected in mode without failure, then we can solve the problem in the clean boot state.
  Step a. refer to the article below for the procedure safe mode in Windows XP
  A description of the options to start in Windows XP Mode
  http://support.Microsoft.com/kb/315222
   
  Step b. You need to perform a clean boot to find the program that is causing and then disable or remove.
  How to configure Windows XP to start in a "clean boot" State
  http://support.Microsoft.com/kb/310353/en-us
  Note: When you are finished troubleshooting, follow the steps as explained in the article to reset the computer to start as usual.
  
  Method 2.
  Also, check the logs of the observer eveny for recent activity on your computer and check.
  This article describes how to use Event Viewer to view and manage the event logs in Microsoft Windows XP.
  Procedure to view and manage event logs in Event Viewer in Windows XP
  http://support.Microsoft.com/kb/308427
   
  I hope this helps.

  Thank you, and in what concerns:
  Shekhar S - Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.
  If this post can help solve your problem, please click the 'Mark as answer' or 'Useful' at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• computer running very very slow and takes place in Not responding mode

  My computer is very slow and when I finally get in line and try to do something or go to another web site, it goes into Not responding mode

  The malware scanner

• Satellite L500-208 does not automatically go to power saving mode

  Dear guys,

  I have a Satellite L500-208 (Serial: PSLS9E) with pre installed Windows 7 64-bit.
  For some time, the laptop does not automatically energy saving mode (as configured in the Power Options).

  Automatic change "Energy saving" worked some time ago and all of a sudden, it stopped.
  However, I do not remember what changed and probably caused the problem.

  Everything works fine and a manual of hitting on "Energy Save Button" also works very well...

  Before you guys suggest an update of the BIOS, the BIOS is version 1.60.
  Current version is 1.90 (or same 2.00?).
  Well, I missed an update and from the Toshiba Web space seems to be very rare, they offer only the latest version of the BIOS.

  Can someone points me to older versions of BIOS, or any that may give a clue to the strange behavior power?

  Kind regards
  Frank

  Hello

  Maybe there's something wrong with the Eco utility.
  I recommend reinstall this tool.
  On the European driver Toshiba page, you will find this tool.
  After the new installation, please check the settings provided by the Eco utility.
  Eventually, you will need to activate the energy saving mode automatic

  Good luck

• Problems running the check disk and disk defragmentation

  I tried to throw a disc defrgmentation and I ask rubbing a disk check I don't know how. I tried to go to the Run comand.com, which is written ' chchdsk/f' and tells me that it is a function of "read only". My system information, it says I have Service Pack 3. Help, please. Everything else works fine.

  When you run chkdsk /f in the command prompt window, you should see a message like this:
  The type of the file system is NTFS.
  Cannot lock the current drive.
  Chkdsk cannot run because the volume is in use by another process.  You want to schedule this volume to be
  checked on the next reboot of the system
  ? (Y/N)
  If you answer "Yes" by typing Y, chkdsk /f turns to the next boot XP (or he will try to run).
  When chkdsk runs automatically restart either because XP thinks he needs to (perhaps your NTFS volume has been marked as dirty) or you have chosen to do it yourself, the results appear in the viewing Application event log.  You should look there for the chkdsk log and no problems after running chkdsk.

  To view the logs in Event Viewer, click Start, settings, Control Panel, administrative tools, event viewer.

  A shortcut to the event viewer is to click on start, run, and in the box enter (or copy and paste):

  %SystemRoot%\system32\eventvwr.msc

  Click OK to launch the event viewer.

  Look in the Application log for a recent event proposed Winlogon, and it should look like this:

  Event type: Information

  Event source: Winlogon

  Event category: no

  Event ID: 1001

  Date: 04/08/2010

  Time: 11:25:57

  Description:

  Checking file system on C:

  The type of the file system is NTFS.

  One of your disks needs to be checked for consistency. You

  may cancel the disk check, but it is strongly recommended

  that you continue.

  Windows will now check the disk.

  Cleaning of minor inconsistencies on the drive.

  CHKDSK checks Usn Journal...

  Audit of the USN Journal is complete.

  39070048 KB total disk space.

  28017948 KB in 100571 files.

  56540 Ko 10556 index.

  0 KB in bad sectors.

  236440 KB in use by the system.

  65536 KB occupied by the log file.

  10759120 KB available on disk.

  4 096 bytes in each allocation unit.

  9767512 total allocation on the drive units.

  2689780 allocation units available on disk.

  Windows has finished checking your disk.

  Please wait while your computer restarts.
  If your report has errors, you may need to run chkdsk /f again until the report indicates no error.  If you get errors, then your hard drive may be failing.
  If you want that take us a look at your report of chkdsk that you see in the event viewer, you can copy it to the Windows Clipboard and paste it back here like this:
  If you double-click on an event, it will open a window of properties with more information.  On the right are black up and down arrow keys to scroll through the open events. The third button that looks like two overlapping pages is used to copy the details of the event in your Windows Clipboard.

  When you find an interesting event that occurred at the time of your question, click on the third button at the top and arrows to copy the details and then you can paste the details (right click, paste or CTRL-V) the text in detail here for analysis
  .  Remove personal information from your information
  After having stuck if you are forced to do so.
  If you paste an event, it will look something like this annoying system startup event:
  Event type: Information
  Event source: Service Control Manager
  Event category: no
  Event ID: 7035
  Date: 14/07/2010
  Time: 17:54:18
  User: Jose
  Computer: computer
  Description:
  The Remote Access Connection Manager service was sent successfully a starting control.
  For more information, see Help and Support Center at http://go.microsoft.com/fwlink/events.asp.
  To get a fresh start on any log of the event viewer, you can choose to clear the log (the log backup is available), and then reproduce your problem, then just look at the events around your show and troubleshoot events that are happening when you have your question.

  Do not guess what the problem might be - understand and resolve it. I need YOUR voice and the points for helpful answers and propose responses. I'm saving for a pony!