Computer says plugged in not supported

Similar Questions

• portable computer does not support. Yet battery monitor says "plugged in, not support.» What are some options?

  my laptop is connected, and yet power monitor says "plugged in, does not support." What are some solutions?

  Hi Joseph,.

  Something similar just happened to me. The first time they fixed it, they have replaced the adapter and the problem is solved. 5 months later it started to happen again and this time they replaced the battery, the motherboard and the milling table (thanks to heaven, it is still under warranty). Fortunately, thanks to the new adapters, battery started to load and the experience does not seem to damage it in any way (but you should keep your eyes on it anyway just in case).

  How they were able to say on my laptop - a Dell E1705 (other than just experience and common sense) was to go into the BIOS (starts, it should be a brief Flash on the screen telling you how to enter the BIOS setup or menu of the BIOS (usually F2) and check the battery information. He showed that the power adapter 'unidentified' instead "90W" list which should be when it is working properly and that the battery was not complete and not charging well plugged. They changed the motherboard and the roll the second time because it could also cause the adapter is not being recognized by the battery (or battery not not recognize the adapter).

  The beep is caused by power and its configured settings to warn you of a low and critical battery condition. In a normal situation, the computer will work right next to the power adapter and does not the battery (it is a way to help maintain the battery life is to run periodically and refill if we leave normally plugged in most of the time). If you remove the batttery entirely, the laptop will power? If this isn't the case, it is certainly at least the adapter or the motherboard. Eventually the battery will get if low, that he's going to sleep or hibernation, or the system stops (you should shut down normally before him to cold shutdown like that). If If, then I expect the tone to go further because it will detect is no longer a low battery charge, because there is no battery - but then you'll want to be sure to use either a battery backup UPS, or at least a surge protector otherwise already in place because if you lose the laptop battery will crash hard and this is not good for her.

  I'm using 32 bit Vista Business SP2 and in Control Panel / sounds / Sounds there is an option for low battery alert. The default to have this. In this case, you can turn off to avoid the beep. In addition, you can go into Control Panel / Power Options, click the plan settings and click on battery. It will provide you with levels of low battery and critical battery and you provide measures to be taken in such a case. If you are unable to operate the system without battery and it is so weak that the alerts began, you probably fell to 11-5% remaining. You can adjust actions to nothing for bass and stop to criticism that 5% is about as close as you want to get to the point where you can hang. Then, you just need to wait until it is repaired and the appropriate parts are replaced.

  Even if you have still some life in it, it is best to contact the manufacturer (they the some have the right parts) or a computer of reputable workshop to get a good diagnosis (perhaps by phone at first), a determination of what must be fixed, the applicable fees, schedule, if it is still under any kind of warranty , and what needs to be done in which order of repair. They can find the adapter is OK and it is just the battery (or vice-versa or two or more). But that's essentially where you need start.

  I hope this helps.

  Good luck!

• App says "SD Card not supported" and "SD card dead."

  When I try to access my 64 GB wireless connect drive, using the application, I get an error red at the top that says "SD Card not supported." It gives me the opportunity to reach a "refresh" - like icon. When I do, it says "SD card dead." It does not allow me to change the settings of the player, nor can I see the contents.

  If I try to connect the disk with my computer, the web browser simply says that it cannot connect to the page.

  When the player is connected to my computer, I can read and write files perfectly fine, it immediately mounts and storage information is displayed in the window management drives in Windows. It is just like normal, like a flash drive.

  The wireless network is displayed correctly, that my computer and the phone are able to connect to the wireless network. However, it is not able to read/write/access to the drive.

  The App also shows that the battery level. It won't show the phone storage space, or it will show the space remaining on the disk.

  Edit: It also just started something really weird. After being plugged into my computer for about 10 minutes, the light starts to Flash quickly and would act as if it was to be disconnect and reconnect the computer for about 15 seconds. And then he stopped. After 10 seconds, he started to do it again. 15 seconds later, it returned to normal and haven't done anything since.

  It had exactly the same problem happen to me and I was about to give up, but finally had a breakthrough, so I made an account just for this post.

  Format the Stick wireless by using the tool "HPUSBDisk":

  http://filehippo.com/download_hp_usb_disk_storage_format_tool/

  Just choose your player, select the "Fat32" filesystem type, uncheck the "quick format" box and click on 'start '.

  Allow the formatting process complete and you should be in business.

  I tried many other methods, including those proposed in the forums and SanDisk KB and it's the only thing that actually worked.

  It is worth noting that when this problem occurred in the first place for me, it's following a format of the WirelessStick (16 GB) on a Windows PC. Following this format, I got exactly the problem that the OP has been/is seen.

• HP Jet 11-r000na portable 32G: my laptop says "plugged in, not charging" what should I do to fix?

  My laptop says "plugged in, not charging" and 0% butter so when I plugged the charger it stops immediately. What can I do to fix it myself? I would really appreciate the help.

  Dear customer,

  Welcome and thanks for posting your query on the Forum from the HP Support

  It seems that your laptop is not charging the battery, we will surely help you this question

  Please run illustrated steps below to solve the problem:

  Step 01. Click the Start button

  Step 02. Type "Device Manager" in the search box of start and open the Device Manager

  Step 03. Get piles and expand it by clicking on the symbol to the left.

  Step 04. Right click on "Microsoft ACPI Control method battery compatible" & uninstall

  Note: This driver battery is re - install automatically when you restart the laptop

  Step 05. Shut down the laptop

  Step 06. Please, remove the battery and unplug the AC adapter

  Step 07. Press and hold the full power 1 minute button

  Step 08. Go ahead and replace the battery and plug the power adapter

  Step 09. Search for "Load connected" message on the battery icon

  After completing all the steps, if you are facing the same question again, please do more than three steps:

  1 perform a check of the battery in HP Support Assistant [install the software, if this is not available]

  Note: Replace the battery if check the health watch replace

  2 update the latest BIOS for your laptop on the Site of HP Support

  3. Please check your laptop with a well known adapter & different from a notebook battery

  Note: If a known good battery also in charge isn't, we need to replace the motherboard

  How to improve the life of a battery:

  Power management must be set correctly for the extended battery life

  Please keep the brightness of the screen to the lower level

  Please turn off the Wi - Fi Connection when not in service

  Please remove the disc from the optical drive when not in use

  Test and calibrate the battery (Windows 8)

  http://support.HP.com/us-en/document/c03325217

  Hope this helps, for other queries in response to the post and feel free to join us again

  * Click on the white button on the right to say thank you Thumbs Up *.

  Make it easier for others to find solutions by checking a response "Accept as Solution" if it solves your problem.

  Thank you

  K N R K

• Acer V5 - 571P says "plugged in, not charging" and battery LED flashes orange from time to time.

  Laptop didn't work when it's plugged in and the battery says "plugged in, not charging." Battery LED also flashes a few times from time to time, so I don't know if it's a circuit board problem or the battery itself.

  I tried updated driver battery without success.

  You can try to unplug the power and remove the battery. Press and hold power for 30 seconds, Plug and see if it is supported.

  Generate a report on the battery

  http://www.howtogeek.com/217010/how-to-generate-a-battery-health-report-on-Windows-8-or-Windows-10/

  Your numbers will be different from the one below, but the left is good, the right is bad.

  

• This computer's hardware may not support booting to this disk

  I get the error message "this computer's hardware may not support booting to this disk" when you try to install Windows Vista on a Western Digital Scorpio 640 Gb SATA hard drive in my laptop Q320.  The laptop works very well with WD Scorpio 320 GB hard drives.  I formatted the disk in the installation procedure and use Diskpart to create a partition/format etc, but still no luck.  I have only one disk in the machine.  Can someone advise. Thank you

  Are you sure you are using the correct bit size on the disk (32-bit or 64-bit) depending on your computer?  Download and check things with the Vista Upgrade Advisor:http://www.softpedia.com/progDownload/Windows-Vista-Upgrade-Advisor-Download-40277.html (although I suppose that it is is not possible if you have already formatted the drive) and at least check the different devices and installed the software in Vista Compatibility Center: http://www.microsoft.com/windows/compatibility/windows-vista/.

  Here is an article on this specific problem with recommended solutions: http://support.microsoft.com/kb/925481/en-us.  Note that it says may be a problem with the BIOS (the installation or version) - so you should check the settings and then contact the manufacturer of the computer for the updates that you can install.

  I hope this helps.

  Good luck!

  Lorien - MCSA/MCSE/network + / has + - if this post solves your problem, please click the 'Mark as answer' or 'Useful' button at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• Error, Windows cannot be installed to this disk. This computer's hardware may not support booting to this disk.

  problem with installing win7 on my toshiba satellite c600 system. during the installation of the OP it says that windows cannot install on the drive. in the detailed information, it says"windows cannot be installed to this disk. This computer's hardware may not support booting to this disk. ensure that the drive controller is enabled in the bios menu. the computer', but there is no such thing of controller in my bios menu. IM using usb to install win7 ultimate. Thank you

  I would check with the computer manufacturer to see if there is an updated BIOS updated.

  Thank you

• When you try to install Windows 7, download "this computer's hardware may not supported booting from this drive.

  I have a LG laptop I want to install Windows 7 on my try to choose a hard drive it says hardware on this computer, but it may not support booting to this disk. Ensure that the drive controller is enabled in the computer's BIOS menu. Please tell me the solution of this problem.

  See the following topics:

  http://support.Microsoft.com/kb/925481

  Boot from the Windows 7 DVD

  Click Install now

  Accept the license agreement

  When the option is displayed to select a type of installation, click (Custom advanced)

  Click on drive Options

  Select the disc/s click on Delete

  Click new

  Click on apply

  Click OK

  Click Format, and then click next to proceed with the installation

• Error: "saying editor does not support the download" while trying to install iTunes

  Original title: download itunes 32-bit for windows 7

  I am struggling to download itunes on the web, I'm in South Africa and consulted the site of SA and the site of the United Kingdom; both sites give me an error msg saying editor does not support the download. my pop - Blocker is set to medium as advised. My PC is 32-bit, and this is the version im trying to download. I don't know what else to do

  Hello

  1. what browser you are using to download iTunes?

  2. What is the error message accurate/complete that you receive when trying to install iTunes?

  3 is the issue limited with the iTunes application?

  4. have you made changes on the computer before this problem?

  Method 1:

   Run the Microsoft FIXIT from the link and if the problem persists.

  Solve problems with programs that cannot be installed or uninstalled

  http://support.Microsoft.com/mats/Program_Install_and_Uninstall/

  Method 2:

   I suggest you to follow the steps from the link and check if it helps.

  Remove and reinstall iTunes, QuickTime, and other software components for Windows Vista or Windows 7

  http://support.Apple.com/kb/HT1923

  Method 3:

  If the problem persists, I suggest you to contact the Apple support for assistance.

  http://www.Apple.com/support/iTunes/

  Hope this information helps.

• I rented a movie in HD and my computer says it will not play on one of my screens because it is not HDCP. What should I do?

  I rented a movie in HD and my computer says it will not play on one of my screens because it is not HDCP. What should I do?

  any suggestions?

• Qosmio F55-Q502 - charging icon says: plugged in, not charging

  I recently had my Qosmio F55-Q502 repaired by Toshiba.
  Two issues have been addressed, and one is fixed.

  However, the second attempted to decide without success.

  When I try to play multimedia games such as call of duty IV, even if the system is completely loaded, a few minutes the system will begin flashing the "Backlight" and then when I see the loading icon, he says: "plugged in, not charging.»

  This really worries me because I read online many similar questions, but none of the solutions seem to work.
  Having to reboot every time that happens and your in the middle of a game, really STINKS!
  I even had what is happening with SimCity4 which is an old game.

  Any suggestions on this good?
  Did they replace the battery when it was sent to which seems to be what most needs to be done.

  Hello

  If your Qosmio laptop was being repaired, I think that you should not discuss any issue on the forums, but put a pressure on the service and specify every single problem with your laptop.
  Please do because the warranty is still valid and it is now time to clarify everything.

  I am not an expert in hardware, but it sounds to me like some electronic power supply question but I can't say for sure. Speak with the service. Try to clarify this with them. Be nice, be cool and all will be ok.

• RAID 0 for a RAID configuration not "this computer's hardware may not supported booting from this drive.

  I want to install a new HARD drive in a tower of the mine to a friend. It was initially created as a RAID 0 configuration with two 160 GB HDD. The replacement is a single 1 TB of HARD drive. I get the message "this computer's hardware may not supported booting to this disk.» Am I missing an approach from a RAID 0 for a RAID configuration, no?

  Hi RegularPencils,

  I suggest that you check in the basic input/output system (BIOS), if you find an option to disable the RAID. If you find, disable the RAID and try to install Windows vista, check if it helps.

  Important: Change (CMOS) BIOS/complementary metal oxide semiconductor settings can cause serious problems that may prevent your computer from starting properly. Microsoft cannot guarantee that problems resulting from the configuration of the BIOS/CMOS settings can be solved. Changes to settings are at your own risk.

  Error message when you try to install Windows Vista on a computer that contains multiple RAW hard disks: "Windows cannot find a system volume that meets its criteria for installation.

  http://support.Microsoft.com/kb/933925

  I hope this helps!

  Halima S - Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.

• I can't install (error says Windows Vista not supported (LR6), I use Windows 7 SP1 worms. 6.1 What is the problem?)

  I can't install (error says Windows Vista not supported (LR6), I use Windows 7 SP1 worms. 6.1 What is the problem?)

  About Vista, but is not https://forums.adobe.com/thread/1836232

• I signed up for the basic acrobat reader conversion program, but he won't let me not convert PDF to Word.  I looked at troubleshooting tips and how advice but after I connect it just says this is not supported and directs me back to sign

  I signed up for the basic acrobat reader conversion program, but he won't let me not convert PDF to Word.  I looked at troubleshooting tips and how advice but after I connect it just says this is not supported and directs me back to register for the conversion program.  I would rather talk to someone, but I can't find a phone number or the option for a cat.  I have a PC.  Any help would be appreciated.

  Hi dianar30180588,

  Try to use the service to export to PDF Online https://cloud.acrobat.com/exportpdf

  Kind regards
  Nicos

• During the installation process of 6 of Lightroom, I get a box that says: Windows Vista not supported.  I have Windows 7 with Service Pak1. I meet all the other requirements listed.

  During the installation process of 6 Lightroom, I get a box that says 'Windows Vista not supported'.  I have Windows 7 with Service Pak 1.  I meet all the other requirements listed.  Any ideas?

  Hi Chuck,

  You can check out the link below.

  trying to install lightroom 6 on windows 7 continues to receive operating requirement not met windows vista not supported

  Hope this will help you.

  Kind regards

  Hervé Khare