Computer * Vista * will not recognize Sansa Clip

Similar Questions

• TWO LAPTOPS WILL NOT DETECT SANSA CLIP 8 GB IN MY COMPUTER

  I have to be very thick, but if I can install an Ipod via itunes, so it must be easy p1ss!

  I'm on my second sansa clip 8 GB, and still my laptop does not detect the device? Why is this?  Ive been hooked up for three hours as the book says, but it does not even recognize it is recharged, the battery power is in the same position, I started the so-called charge upward, and he did not move!

  the strange thing is, if I plug it into my usb HP printer port, accusations of bloody thing?

  Im confused, Ive formatted, like three times, Ive changed to automatic detection, MSC and MTP but still nothing...

  IM using Windows XP

  The usb cord little has the same end for my N95 8 GB, so I plugged my phone on my laptop using the same USB cable and it works, but for some reason this sansa will not be detected, Ive tried all ways and always make me not anywhere with her

  I don't not even a small icon in the system tray, it's in my head

  IS IT BROKEN?

  Yours, lost

  A few things to try:

  -Another USB cable.

  -Another USB port, especially one in the back of your laptop.

  -Try to set the video mode USB MSC under settings of the element.

  -Try a system reset (with the music turned off, hold the on switch upward for 15-20 seconds).

  I hope that one or the other will do.

• Computer Vista will not print to Deskjet 930c on home network

  Our three computers (Vista is A, B, and C are XP) are connected to a wired network of private home.  Computer A has a Canon printer that is shared and all 3 computers can print to that very well.  Recently, we re-gasket a printer HP DeskJet 930C to computer B (via USB) and shared.  Computers, B and C can be printed on the HP very well.

  But, even if A computer can see the printer, it will not print.  He seems to accept the print command and sometimes a dialog box flashes on and so quickly as it cannot be read, but nothing prints.

  I worked through the Microsoft article "File and sharing printers in Windows Vista" at http://technet.microsoft.com/en-us/library/bb727037.aspx#mainSection and you don't see anything that solves the problem.  I ran the doctor of printing & scanning HP and who wrote the 930C is installed but not connected.  According to the website of HP, Vista has the correct driver.  I have uninstalled and installed the printer from computer A, but it still does not work.

  So I called HP Support, and they said that I had done all the right things, and "it must be a registry problem.  This seems unlikely to me, and I don't know where to look in the registry.

  Any ideas or solutions?

  Hello

  Windows XP sharing can be done automatically in XP or operating systems, XP does not host the drivers for the newer Vista operating systems and so you will have problems with some models.

  To manually add the shared printer, follow these steps:

  1. install the printer locally in following second method: connecting the cable in parallel below:

  http://support.HP.com/us-en/document/c01655752

  2. go into your PC host (computer B), right click my computer and select Properties.

  Find the name of computer on this screen.

  3. go in Control Panel > printers and faxes.

  Right-click on the printer and select Properties.

  Open the tab end hand note the share name

  Note: I would say keeping the name of sharing as simple as possible (e.g., 930C)

  4. go to your Vista machine and open Control Panel > printers.

  Click with the right button on the 930c configured in step 1 and select Properties.

  Open the Ports tab.

  Click Add a new port.

  In this list, select Local Port.

  Set the local port in the form of \\Computer B Name\Printer share name (for example \\PC-P\930c).

  Confirm the changes and check any change.

  If you have still any question, I would say that the printer is connected to the Vista machine, then share it with the XP PC and check for any changes that should run more easily from my experience.

  Shlomi

• Vista will not recognize the projector connected for multiple display

  I'm under a system dual boot with Windows XP and Vista.  When running under XP, I doesn't hurt to connect a projector to my laptop and extend the desktop on the projector for meetings and others.

  When I am running Vista, it does not even recognize that the projector is connected.  However, once I have connected the projector, if I reboot the system, it will then display on the projector.  If I disconnect the projector, the screen does not reappear on the screen of the laptop, I have to restart, with the projector removed for office reappear on the screen of the laptop.  I'm hoping to get multiple monitors to work with Vista, as it does in my XP boot.

  For the purpose of the next presentation running in XP is not an option.

  Hi cptrigeek

  Try these steps and check if that helps:

  Method 1: We can try to perform a power cycle of the projector.

  Remove the cable from the power of the projector and this continues for 5-10 minutes. Also do the same for the laptop, Dungeon, it off. Then put back in place and start the projector. Now, start the laptop as well. Connect now. Now, you will need to install the driver for it (if there is one). After which, you need to configure the settings of the laptop.

  Method 2: Check the following steps:

  1. connect the projector to your Windows PC. NOTE: the following steps apply if you use your PC in MIRROR mode only.

  2. on the screen of the computer, right CLICK on the desktop and select Properties.

  3. click on the SETTINGS tab. If you want that your displays in mirror (what you see on laptop, it's what the public sees) you must make sure that the box "extend my desktop to this monitor" is DISABLED. If you see a box of "mirroring", remember to check it out.

  4. drag the slider to 1024 x 768 screen. As a general rule, the external monitor may limit this parameter. If your screen is higher, it might not display on the projector, then you want to test this until you're ready to take the floor. Drag the color to highest (32 bit) if available or medium (16 bit) quality if the first is not available.

  5. now select FN and press the function key. This key is usually given by a small screen icon, the CRT/LCDtext and is usually found on F8 or F5 even. Press the appropriate operation button ONCE and wait. After a few seconds, the second screen should light up. Be patient, it may take up to 5 seconds. On the projector, it may take up to 10 seconds for the projector to detect your system and switch. Note: a second press of this function (in general) will switch to monitor EXTERNAL only. A third press stop INTERNAL onlyand the circle for each push after that. Also note that some laptops can do this sequence in a different order, so learn your system so that you can quickly to the desired mode.

  6. click on the ADVANCED button. If 'apply the new settings to display without restarting' is not selected, select it. Under screen refresh rate, select 60 Hz. click APPLY and CONFIRM the choice. Click OK to close the ADVANCED options dialog. Close the display properties dialog box. You should now see a mirroring of your monitor on the second monitor.

  7. test: A test, disconnect the second monitor. put your mobile PC to sleep. He wakes up and let it fully come (login if necessary), and then reconnect the external monitor. On some machines, he needs to quickly display the screen in the last known state (you may need to wait up to 10 seconds). If it is not correctly displayed, press the switch function, ONCE. Yet once, note that it can take up to 10 seconds to view, so be patient. If only the projector display now, some pressure on the function switch key should provide for both screens again. If you can't get the projector to display, check all your connections and settings above.

  8 Note that when you use the projector, after pressing the function for changing the monitor button, it may take up to 10 seconds for the monitor find and block on your machine. Just wait. Pressing on the keys new fkey can simply ruin your settings or turn off the projector.

  9. not all laptops work the same way. Please make sure you learn how your work before you get to your presentation.

  (Not mirrored)

  1. If you do NOT want mirrored poster (display of different internal and external), CHECK the box next to the line that reads "extend my Windows desktop to this monitor." This SHOULD result in the external monitor display an image which is an EXTENSION of the current desktop.

  2. in the settings dialog box, the internal monitor appears as a '1' and externally as a '2 '. Click ONCE on the '2 '.

  3. with '2' selected, drag the Screen Resolution slider to the left or to the right until the resolution reads "1024 x 768". Also affect the quality of the highest (32-bit color) if available or average (16 bit) if the first is not available.

  4. click on the ADVANCED button. If 'apply the new display settings without restarting' is not selected, select it.

  5. Select the MONITOR tab. Under screen refresh rate, select 60 Hz. click APPLY and CONFIRM the choice. Click OK to close the ADVANCED dialog box. Your system is now set for an extended desktop. When it is connected to the screen, you may need to use the function switch key to turn once more on this option, but on systems that I tested, the extended desktop comes just when the monitor is connected. Yet once, I suggested some tests with this mode of knowing how your laptop will perform when connected to an external monitor before coming to speak.

  6. notes that, in this mode, items moved to the extended desktop can be "lost" it if the external monitor is disconnected because they live on the extended desktop is no longer available. Also note that if the extended desktop is turned on, this part of funds 'second' can continue to live, which means that the cursor and the object can be moved off the screen in this sector and not be visible on a single internal monitor. To resolve this problem, do a right-click on the desktop, select Properties, select settings, click on the '2' box and UNCHECK the extend option. Items left on the extended desktop should now align the right edge of the internal display.

  See also: http://windowshelp.microsoft.com/Windows/en-US/Help/16152337-a45c-4a1a-b302-cfd95399ce071033.mspx#EQB

  Understand multiple monitors: http://windows.microsoft.com/en-US/windows-vista/Understanding-multiple-monitors

  Set up multiple monitors: http://Windows.Microsoft.com/en-us/Windows-Vista/set-up-multiple-monitors

  Multiple monitor issues: http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-multiple-monitor-problems

  After back and let us know if it helped to solve your problem.

  Thank you and best regards,

  R uma - Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.

• Computer Vista will not start, the computer keeps restarting. Also had a BSOD "STOP: 0 x 00000024 (0X8D5389C, 0X8DB535CC, 0X001904AA, 0X8CC143A1)" while trying to use reinstall OS Dell drive

  Original title: corrupted vista OS?

  My Dell studio slim desktop (Vista OS) that I have since Mar09 died on me 2 weeks back and I can't it start and it will keep rebooting until it resembles the wide long beep (as if a deceased person)

  Whenever my com has restarted, it shows the following:

  Safe mode

  Safe mode with networking

  Safe mode with command prompt

  Last known good configuration (Advanced)

  Start Windows normally

  All options will be led to the recovery of my com & return the same screen.

  It will always get stuck at the loading bar where the com starts boot & restarts itself.

  I tried to attach the hard drive to a different com as external hard drive, but it will begin to restart that com & hang the CMO as well

  I tried using the disc to reinstall OS from DELL and it will show a msg of error (blue screen) with the following text:

  Disable or uninstall the antivirus, Defrag disk or backup utilities. Check the configuration of the hard disk & check for any updated drivers.

  Run CHKDSK /F to check for hard drive corruption, and then restart your computer.

  STOP: 0 X 00000024 (0X8D5389C, 0X8DB535CC, 0X001904AA, 0X8CC143A1)

  NTFS.sys address 8CC143A1 base at 8CC06000, Datestamp 47918a 96

  Any idea of this situation?

  Is it possible to save my cause com have not all backups from my hard drive?

  Any help would be grateful.

  Thank you

  Hi Bill,

  I forgot to include some info as well... I replaced the 'touched' hardisk (Barracuda 500 GB) to an unused a (Barracuda 160 GB) and the problems disappeared. Whenever I change back the 500 GB in the com, the sound signal occurs only backwards the system continues the reopening for abt... 10 + times?

  "My Office studio slim (Vista OS) Dell I have since Mar09 died on me 2 weeks back and I can't it start, and he'll keep rebooting until it seems a beep long-lasting looks not (as if someone died).

  So the questions are now fixed, unless you put the other disk hard?

  Test the other hard drive.

  Go to the website of your computer manufacturer > find specifications of hardware in your computer (hard drive) > access the Web Hard Drive from the manufacturer site > download their diagnostic software > make a Bootable disc > test your hard drive.

  And run the F12 as I advised you to do so.

  It is DELL's Diagnostics software.

  Good luck with it.

• Computer Vista will not be stopped

  I tried to shut down my computer for days now.  Vista - and still running, he simply refuses to stop.  Suggestions anyone?  I have all the SP2 updates and I tried just August everything I read about to solve this problem... except the only thing that works!  Thank you

  Hello

  This problem can occur when the power management profile turns off your network adapter.

  Method 1: disable the functionality of management of power in network adapters

  a. click on start

  b. right click on computer

  c. click on manage the

  d. click on Device Manager in the left pane of the window

  e. expand your network card.

  f. now you will see your network adapter or adapters if you have more than one. Right-click on the network component, and then click Properties.

  g. go to the power management tab.

  h. ensure that all of the checkboxes are checked (check boxallow the computer to turn off this device to save power is off).

  i. When you have disabled the boxes, click ok and restart your system. Put the computer in mode 'sleep' and check if you still have any questions.

  Method 2:

  If the problem persists, you can try to perform the clean boot and check if it helps:

  How to troubleshoot a problem by performing a clean boot in Windows Vista and Windows 7.

  http://support.Microsoft.com/kb/929135

  Note: Don't forget to reset the computer to start as usual, once the problem is resolved. Follow step 7 of the KB article.

• Computer Vista will not "Shut Down"

  Why is Vista not 'Shut Down' when we try to? The computer gets to that stage and works on and until what we manually turn off the computer.  When we click on Shut Down, the OS disconnects then goes down at the stop, but isn't.  Anyone facing this problem.  It is found on all 3 computers OS Vista

  Also, when updates Windows tries to install computers work for too long at a time in the mode of installation on the same day.
  Don't know if they are related.
  Thanks for the tips.

  Hi jem820,

  ·         When was the last time it was working fine?

  ·         Have you made changes on the computer before this problem?

  ·         You receive an error message all in stop or restart the computer?

  Follow these methods.

  Method 1: It could be due to a program or device driver interfering with Windows power settings. See the article and try the steps in the article.

  Why my computer won't turn on or off quickly?

  http://Windows.Microsoft.com/en-us/Windows-Vista/why-wont-my-computer-turn-on-or-off-quickly

  Method 2: Install the updated drivers for the graphics card on the computer visiting the site of computer manufacturer.

  Updated a hardware driver that is not working properly

  http://Windows.Microsoft.com/en-us/Windows-Vista/update-a-driver-for-hardware-that-isn ' t-work correctly

  Method 3: Perform a clean boot to see if there is a conflict of software like the clean boot helps eliminate software conflicts.

  Note: After the boot minimum troubleshooting step, follow step 7 in the link to return the computer to a Normal startupmode.

• Vista will not recognize or find applications

  At the opening of the applications, I get error messages that the application cannot be found.  I can find them manually, but when I opened the they are not associated with a program.  I can't select box 'always open this file with this program.  I tried to run the system restore, but I don't know what kind of program to associate with.

  You don't need to know what program to associate in order to run the system restore.

  It soundls like the file association for. Files EXE is corrupt or missing or wrong.  Here is an article on how to fix: http://www.dougknox.com/xp/file_assoc.htm (the entry corresponding to the choice. EXE files).

  If this does not work, do a restore of the general system.  Do you know when this problem started?  Try a system restore to a point in time BEFORE the problem started.  Here is the procedure: http://www.howtogeek.com/howto/windows-vista/using-windows-vista-system-restore/.  Don't forget to check the box to show more than 5 days of restore points.  If the first attempt fails, then try an earlier point or two.  NOTE: You will need to re - install any software and updates that you have installed between now and the restore point, but you can use Windows Update for updates.

  I hope this helps.

  Good luck! Lorien - MCSA/MCSE/network + / has + - if this post solves your problem, please click the 'Mark as answer' or 'Useful' button at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• Computer Vista will not complete start up once the updates have been installed

  Office worked well on 20 January, until the update when you restart it should start going to black screen with cursor. I tried to fix it, but it does not work. I tried the system restore to an earlier date but gives the error. Does anyone have ideas, which is false.

  Thank you

  Lisa,
  At this point if you have a way to back up your data, I suggest that do you so as soon as possible.  Start the XP that you have installed.  Then copy all your data from the original Windows folder to an external drive or a DVD.

  Then, to try to make this repair, boot from the XP disc and select the recovery option.  This will start you in the recovery console prompt.  From there, you can then run the commands to replace the sam file.  Mike - Engineer Support Microsoft Answers
  Visit our Microsoft answers feedback Forum and let us know what you think.

• Computer Vista will not format DVD RW drives more

  I have problems with my DVD disc burning, windows formateront is no longer my DVD - RW discs but will format my DVD-R discs, what can I do as I don't like having to use disposable DVD discs all the time? I'm just a learner so im very confused, please help me... thanks

  * original title - formatting issues. Windows reformatted is no longer my DVD - RW discs.*

  Hi nicky271,

  ·         Did you format the disc earlier?

  ·         Remember to make changes?

  ·         What happens when you try to put in the form of these discs?

  Step 1: We will uninstall the DVD drive in Device Manager and reinstall. Automatically search for updates to the firmware on the manufacturer's Web site.

  a. click the Start button and then right click on computer. Click on properties.

  b. click on Device Manager.

  c. now, expand the CD-ROM/DVD-ROM drives, click with the right button on the CD-ROM/DVD-ROM drive and click on uninstall.

  d. restart the computer.

  Step 2: Log on to the manufacturer of the DVD drive and install the latest updates from driver\firmware.

• Computer will not recognize Pro Duo or removable drives.

  Computer Vista will not read my Pro Duo chip, or it will show all removable drives except ROM USB where I have an optical mouse wirelesss connected (when I check my computer).  The import wizard shows only a USB where prior that he showed, f, g, h, etc.

  Thank you.

  Thank you for these two answers, unfortunately the first did not work, and the second deals with USB.  The computer will not recognize any location chip memory, they do not appear on the Import Wizard, or MY computer.  The only two drives that appear are drive C and drive J, which is where I have a wireless mouse hooked up.   Just before this problem I had... and still not... a bottom of screen message "one of the USB devices attached to this computer has malfunctioned... Click this message for more information."  The only connected usb is the mouse, and it works fine.  Solutions that deal with USB issues aren't really questions I have, except that in the future (if the problem remains) USB ports do not appear on my computer either.  Someone who has some said knowledgge I need to re - map the hard drive, or something?

  I really appreciate the time you people consume with it.  Any other ideas?

• Vista does not recognize Avast!

  Hello all :) - for the last 3 months or more, Vista will not recognize that Avast! is running and antivirus protection. I've been running Avast on Vista early IE May 2007 and not had this or any other problem. I was hoping that it would fix itself, but no luck... I'm confused as Avast! tells me that everything is fine. Does anyone else have this problem? What can I do? I have Vista Home Premium, to date and legal lol. Thank you all very much. This is a wonderful forum!

  I find the rest of the article in support of Avast, try it and he could solve the problem:

  https://support.avast.com/index.php?_m=Knowledgebase&_A=viewarticle&KBArticleID=580

  I also believe that you could contact Avast assistance by phone, if you forgot the password for support or you can click on password to the website to reset your forgotten password.

• Why my WMP will not recognize my Sansa E260 player?

  I connect it via USB and the media player will not recognize.
  Two years ago, that he did it. I got a lot of work on my PC since then. Anyone familiar with the Sandisk players?

  Hi thomwilliams,
   
  -What version of Media Player do you use?
   
  Try the steps listed in the article below and check if it helps fix the problem:
   
  Sansa player not recognized by the computer
   
  There is an update firmware released for the Sansa Player. Download and apply the same and see if the problem is resolved.
  Sansa player not recognized do not update to firmware Sansa

• my computer dell laptop with windows vista does not recognize the battery what should I do?

  I have a computer dell laptop which will not recognize the battery what should I do?

  Contact Dell for hardware support.

• Win 7 64 bit computer will not recognize the old jpg files since 2003 of the records that have been transferred to an external hard drive.

  Win 7 64 bit computer will not recognize the old JPGs from three 2003 files that were transferred to an external hard drive...  File appears in the directory but with no thumbnails icon. Does not open in the Viewer, Picassa, Ifranview, paint, PhotoShop.  I get conflicting messages... invalid image (Windows Viewer)... Unknown file format (IfranView)... Access has been denied (painting), a blank image (Photoshop),... You are not allowed to open this file (Picassa).

  Creation 2007
  Last updated on 2003
  2010
  Any help would be appreciated.

  Mahalo,

  Philippe

  Ran the Scan, the system is secure.

  I was able to bypass stubborn files to transfer them to a flash drive and copy them to another folder.  I was then able to access.  Somehow I messed up the permissions in the previous transfers of old machines and OS.

  Thank you for your help and attention.

  Mahalo,

  Philippe