Computers with static IP address, get addresses (169.254) APIPA

Similar Questions

• Ethernet on external device with static IP address

  I'm trying to connect my external station of development (Visual Studio in Windows XP/Fusion on my Mac) for Windows CE device through an ethernet cable crossed for the CE - device debugging.

  This forces me to set a static IP address on the external device and the development station.
  Both must be on the same subnet. How can I do this?
  I tried to use the Bridged (ethernet) mode on the network card and set up a static IP address in windows XP. I also created another static IP address in OSX. Looking at the IP/ethernet side traffic OSX (using Wireshark), messages from the external device IT appears, but glancing Wireshark in merger/Windows XP, I don't see them.
  Am that I on the wrong track here with the Bridged mode?

  First of all you shouldn't have to use a crossover cable as Ethernet adapter of the Mac must Auto-Sensing and automatically process the cross above a straight through cable. (At least this is so on my Mac.)  Secondly, I would not give the host a IP road-able and only set the IP in the - CE device and virtual machine with no gateway/DNS IP address. When you use a NIC jumpered in the Virtual Machine.

  On the host if the Ethernet adapter using DHCP then you will have to wait for it to expire and get a 169.254.0.0/16 address IP or if you want an answer more quickly then manual assign a 169.254.0.0/16 IP address for the host's Ethernet card.  In this way communication is directly between the - CE device and virtual machine using VMware Bridge Protocol.

  If you do what the host itself to have connectivity in this loop, then of course assigns an IP address appropriate with no gateway/DNS IP address.

  Example of IP address Configuration

  CE-IP address: 192.168.3.1/24

  Address Virtual Machine IP: 192.168.3.2/24

  The IP address of the host: 169.254.0.0/16 or 192.168.3.3/24

  No gateway/DNS on any IP address.

• Help with static IP address for the WRT54GL by EZXS55W

  Hi all!

  I'm having some trouble network at the office and cannot keep close internet for all the world just try a new mode of connection of the cables.

  We recently received a notice on five new static ip addresses for the office, we did turn on DHCP those for a year now.

  We have a basic network requiring no credentials of the modem or connection.

  At this moment we have a network cable straight from the network on the router (WRT54GL) failure. Then, the router is defined in gateway mode and uses one of our static Ip addresses.

  I wanted to connect my server to the same fault, but using the static IP address, so I thought why not do it through a switch.

  So the network failure, I ran the right network cable into the uplink on the switch (EZXS55W) connector and then put the router in port 1 and my server port2. Both connected with the right cables.

  The Internet light on the router does not light and the switch just flicker light now and then.

  Maybe someone here can help me how I should put up to get to the top and running, what do I have to configure something special on the router or maybe somewhere use twisted cables.

  Please I need your help!

  Thanks for the help and you where once there was something wrong along the way.
  I tested my switch before trying this, but apparently it is now broken.
  I borrowed another switch of a friend and everything was up and running in a few seconds.
  So now I just need to buy a new switch and everything will be fine.
  Once agan, thank you...

• How to remove the default for a limited only account gateway (with static ip address)

  I have 1 pc with 4 accounts 1 account administrator and user the rest is limited accounts. I use a static ip address and the question is how to remove the default gateway on these limited account so that they cannot access the internet

  The entry door is fixed to the adapter and selectively cannot set properties of the different adapter for different users, all users use the same adapter.

  With Internet Explorer (does not work with other browsers), you can configure a proxy server with a fake address, you can do this through Group Policy, or you can do it manually for each individual user through the Internet Options settings.  You can set the proxy server address map of loopback (127.0.0.1) or you can set it to a bogus address of your private address range (usually the range 192.168.xxx.xxx)

  If you are using other browsers, you can use NTFS permissions to deny access to the Explorer or the program directory or you can use software restriction policies to deny access to specific programs.

  Alternatively, you can use a logon script to activate the network connection service when you open a session and the other to turn it off when you log, but if you do this you will disable the entire network for limited users if it cannot be a solution for them.  The script can be a simple two-line script:

  Logon script:

  SC config Netman start = demand
  net start netman

  Logoff script:

  net stop netman
  SC config Netman start = disabled

  These can be useful:

  http://www.howtonetworking.com/Internet/restrictie11.htm
  http://www.christianblog.com/blog/abelajohnb/disable-Internet-access-in-Windows-for-specific-user-accounts/

  John

• need to configure a connection wireless network with static IP address to make a panasonic wireless display of work on the virtual machine

  Hi, I'm new to macs and Fusion. I have a MacBook Pro 13 mid-2009, running 10.5.7 and Fusion 2.0.5, running Win XP Pro SP3 as the virtual machine (not in a bootcamp partition separate). I added a second network as a bridged network adapter (first one is set to NAT). I'm trying to connect my wireless panasonic (802 11b) to the virtual machine display, as I do on my old sony PC. Normally, I turn on the wireless on the PC, find the network wireless in Win XP and configure my SSID and necessary of static IP address and configure the NIC to search only ad-hoc connections (non-infrastructure). I also turn off the firewall so that it can work. There is a panasonic program runs on the PC (which I also installed on the virtual machine) makes it all happen once I have the connection. So the place that seems to be stuck, it's that I can't find a wireless to configure network adapter since--what the VM is a NA standard, so there is no place to specify the SSID, ad-hoc and disable the WEP key. Someone has ideas how to go beyond my current state?

  In addition, the panasonic only works at 800 x 600 for the display resolution, so it will automatically change the graphics settings. I guess that's not a problem on the VM, but thought I would ask in advance in case someone sees a problem with it.

  Thank you very much.

  Larry

  If the only way you can connect to the device is via WiFi, then you will need to provide your own WiFi USB network adapter to the virtual machine because Fusion presents only the network card Ethernet wired to the Virtual Machine, regardless of the host network adapter is the main map.

• Clients with static IP addresses

  Total newbie here. My PIX-501 works fine for customers on the network using DHCP from the firewall for their IP addresses, but I can not configure the clients to access the internet that have static IP addresses. What should I use as the default gateway and the DNS server in the TCP/IP configuration on client machines? The PIX has an IP extrnal 192.168.254.253 that connects to a router and internal IP address of 192.168.1.1. Thank you

  Hello

  Inside your configuration TCP/IP client/PC point the default gateway the IP of your i.e.inside your PIX PIX interface address inside, I presume it is 192.168.1.1

  Let me know how you go.

  Jay

• List of virtual machines with static IP

  VMware gurus,

  I'm trying to generate a list of virtual machines that are configured with static IP address.

  IPPolicy: static

  I need a script that returns the name of the virtual machine that has static to IPpolicy.

  Jadapa RHCE, MCSA

  http://linuxgurus.WordPress.com

  You can create a list of virtual machines with static IP addresses with the following script PowerCLI:

  Get-VM | `
    Get-VMGuestNetworkInterface -GuestUser User -GuestPassword Password -HostUser User -HostPassword Password | `
    Select-Object -property VM,IPPolicy | `
    Where-Object {$_.IPPolicy -eq "Static"}
  

  Best regards, Robert

• Unable to connect to the Simulator (169.254.0.1)

  I installed the new Simulator available for VMware Player and have successfully startet it. (Windows 7)

  The Simulator have internet access (I launched a web page in the browser)

  But I can't connect to the device either by ping it in cmd command prompt or the

  plugin in eclipse.

  It is said in the Simulator: use development mode ON and development addresses 169.254.0.1

  Any ideas?

  The value in the security setting is the IP address that will be used when a PlayBook is connected via USB.  You can connect the debugger using the WiFi IP address or IP address of the USB device.

  In the case of the Simulator, the USB connection is not possible if you need to connect using the simulated WiFi connection.

  The icon on the home screen shows all of the IP addresses, you can use to connect to (it will show WiFi and USB IP addresses if both are available).

• "Error: failed to get the IP address of the destination virtual machine running the converter to assistance server." with a static IP address

  Hi all

  I'm trying to p2v linux 6.4. It fails with the following message is displayed:

  Error: Cannot get the IP address of the virtual destination machine running the converter assistance server.

  I have seen discussions on this message, but they all refer to dynamic IP address, taken from DHCP, as in my case, I use static IP address.

  In the meantime the p2v (which then breaks down...) I open console support machine and saw a message:

  
  

  eth0 is not a recognized interface.

  Can someone tell me what is happening?

  Hello

  I assume you are using converter 5.5. There is a new feature that allows the selection of the network card. However, it works well in the case of Linux P2V. If you have changed the type of adapter, use 'e1000' or 'auto' and try again.

  HTH

  Plamen

• Only 1 of the 2 computers in my LAN recognizes my static IP address assigned by my ISP - HELP!

  I have an IP address from my ISP, but only one of the two computers in my LAN presents this static IP address in the "ipconfig" and it connects to the internet, the other computer Watch has "169.254.XXX.XXX' IP address and does not connect to the internet.  How can I fix it? I don't know much about the TCP/IP settings.  OS is XP Pro SP3.  I have a DSL router from single port connected to a simple switch 5 ports, then two CAT5 cables will switch on both computers.

  Thanks for your help!

  derisk

  Hello

  Two computers cannot connect to the same connection using the same IP address. Each computer on the network must have its own unique IP address.

  You need to get a cable/DSL router. Configure the WAN port (Internet) side with your static IP address and connect all the computers the and other equipment network on the side of the router LAN.

  Generally, it looks like this, http://www.ezlan.net/network/router.jpg

  P.S. You don't need to use the wireless if you do not, it is very difficult to find a new wireless router.

  Jack-MVP Windows Networking. WWW.EZLAN.NET

• Bind the MAC to the static IP address with WRT54GL router

  Hello

  We use the WRT54GL Wireless router to connect 4 pc to internet. One of these pc requires a static IP address, because the router can do only reliable port-forwarding for IP static (I would ssh it and use it as a web server). I was told that this router has this ability, but for the life of me I can't find.

  Could someone tell me how to proceed? I am running the latest firmware (v4.30.11).

  Thanks in advance for your reply,

  Michiel

  DD - WRT is fairly stable and well maintained. There are a lot of people using it and you get excellent support, if you don't mind not very technical responses to opportunities. Generally, the flashing of the firmware does not support the warranty. But that wouldn't be a problem if you have had a bad flash. And even for a bad flash you often have options to recover the router.

  For the static IP address on the computer, change the settings of network to the ethernet interface. I do not know Gentoo you should have administration GUI for this somewhere.

  You can use the following values:

  IP (as mentioned earlier) for instance 192.168.1.10
  subnet mask 255.255.255.0
  address of the gateway 192.168.1.1
  192.168.1.1 DNS server

  As long as the static IP addresses do not conflict with the DHCP server address pool create there will be problems running some static IP computers in the same local network with DHCP clients.

• Cannot get internet static IP address

  Hi, I put several new Win7 PC in an office that replace Win XP PC. I need to use static IP addresses on all of the PCs, as it is required to access the Unix server. Start of the new PC with internet access very well, but when I assign static IP addresses, they have more internet. My IP address, DNS server, gateway, etc. are all correct and identical to what is plugged into the PC XP (except IP address of course). Even if the new PC do not have internet access, they can connect with the Unix server and other PCs on the working group. When I diagnose the problem I get the answer: "your computer seems to be configured correctly, but the device or resource (DNS server) is not responding." All the XP computers using the static IP address and have the internet very well. Yes, I already tried to clear the DNS cache.

  Hello

  As you work on a domain network, the question would be better suited on the TechNet support forum.

  I suggest you to check with TechNet support for more information.

  http://social.technet.Microsoft.com/forums/en-us/newThread?category=&Forum

• HO OfficeJet Pro 8600: how to remove a static ip address on my HP 8600, using mac 10.7.5 work with wifi

  I have trouble printing through my wifi network. How to remove a static ip address on my HP 8600, using mac 10.7.5 to work with wifi?

  With the help of my NetGear N900 / CG4500BD modem/router with DHCP, there are different IP addresses of the printer, if the printer is connected is 192.168.0.13, when the printer use wifi IP is 192.168.0.20, and on the printer, it shows 192.168.1.142 I think is a static IP address, because it can cause the confussion.

  I appreciate your help, thank you, the Job Dr.

  Hello

  Please go to system-> Network Preferences. Select the airport on the left, and then click Advanced in the bottom right. Switch to TCP/IP and select "using dhcp". Click ok, and then click on apply. After a few seconds, you should get an IP address from the router.

• Static IP address for printer with a wired connection

  My printer (HP7210) is wired connected to my WRT54GL router. 2 computers also have a wired connection, my laptop is connected wireless. All of these computers use the connected printer. 2 computers can only use a static IP address for the printer. How can I set a static IP in my router?

  I don't think that the WRT54GL supports static IP with the stock Linksys firmware.

  The solution is to assign the static IP address to the printer. Most of the printers on network supports the definition of a static IP address manually. The key is to set the static IP address on the printer out of the range the WRT54GL uses for its DHCP server. Sign in to the administration page of your router and see what addresses the range of IP addresses he uses to hand over the IP address of the client. Usually, Linksys likes to start xxx.xxx.xxx.100 and have leases of 50 to 100 a cancelled so to avoid conflict, you can use any IP in the range of xxx.xxx.xxx.002 through xxx.xxx.xxx.099, or through xxx.xxx.xxx.254 xxx.xxx.xxx.201. After configuring the IP static on the printer, you may need to reconfigure all the print drivers that are already installed on client computers so that they can connect to the new static IP address to the printer.

  See the user guide page 140 to learn how to manually change the IP of the HP 7210 printer settings.

  For example try using the next/IP subnet mask if your router is configured to use 192.168.1.100 to its DHCP server setting:

  Use the IP address of: 192.168.1.202

  Use the subnet mask: 255.255.255.0

  Use the gateway: 192.168.1.1

  To change the IP of the control panel settings

  1. press Setup.

  2. press 8and then press 3.

  This selects the Network Configuration , and then IP settingsmenu.

  3. press on until Manual appears, then press OK.

  4. change the IP address, and then press OK.

  5. change the subnet maskand then press OK.

  6. change the default gatewayand then press OK.

• Cisco ASA5520 facing ISP with private IP address. How to get the IPSec VPN through the internet?

  / * Style definitions * / table. MsoNormalTable {mso-style-name : « Table Normal » ; mso-tstyle-rowband-taille : 0 ; mso-tstyle-colband-taille : 0 ; mso-style-noshow:yes ; mso-style-priorité : 99 ; mso-style-qformat:yes ; mso-style-parent : » « ;" mso-rembourrage-alt : 0 à 5.4pt 0 à 5.4pt ; mso-para-marge-top : 0 ; mso-para-marge-droit : 0 ; mso-para-marge-bas : 10.0pt ; mso-para-marge-left : 0 ; ligne-hauteur : 115 % ; mso-pagination : widow-orphelin ; police-taille : 11.0pt ; famille de police : « Calibri », « sans-serif » ; mso-ascii-font-family : Calibri ; mso-ascii-theme-font : minor-latin ; mso-fareast-font-family : « Times New Roman » ; mso-fareast-theme-font : minor-fareast ; mso-hansi-font-family : Calibri ; mso-hansi-theme-font : minor-latin ;}

  Hello guys,.

  I have Cisco ASA5520 facing the ISP with private IP address. We don't have a router and how to get the IPSec VPN through the internet?

  The question statement not the interface pointing to ISP isn't IP address private and inside as well.

  Firewall configuration:

  Firewall outside interface Gi0 10.0.1.2 > ISP 10.0.1.1 with security-level 0

  Firewall inside the interface Ethernet0 192.168.1.1 > LAN switch 192.168.1.2 with security-level 100

  I have public IP block 199.9.9.1/28

  How can I use the public IP address to create the IPSec VPN tunnel between two sites across the internet?

  can I assign a public IP address on the Gig1 inside the interface with the security level of 100 and how to apply inside to carry on this interface?

  If I configure > firewall inside of the item in gi1 interface ip address 199.9.9.1/28 with security-level 100. How to make a safe lane VPN through this interface on the internet?

  I'm used to the public IP address allocation to the interface outside of the firewall and private inside the interface IP address.

  Please help with configuration examples and advise.

  Thank you

  Eric

  Unfortunately, you can only complete the VPN connection on the interface the VPN connection source, in your case the external interface.

  3 options:

  (1) connect a router in front of the ASA and assign your public ip address to the ASA outside interface.

  OR /.

  (2) If your ISP can perform static translation of 1 to 1, then you can always finish the VPN on the external interface and ask your provider what is the static ip address assigned to your ASA out of the IP (10.0.1.2) - this will launch the VPN of bidirectionally

  OR /.

  (3) If your ISP performs PAT (dynamic NAT), then you can only start the tunnel VPN on the side of the ASA and the other end of the tunnel must be configured to allow VPN LAN-to-LAN dynamics.