ConfigFree locks access - point impossible to Exchange to another

Similar Questions

• Cannot connect by Satellite L300 wireless access point

  I have a new laptop L300 & I can't connect to the laptop to my wireless access point. I have an another mobile E-sytems with the same hardware Realtek RTL8187B & it connects without problems.

  The machine has the free two month Mcafee subscription & I have disabled all the protection incase that was causing the problem. I updated the driver for the wireless card & the bios on the Toshiba site, but nothing is.

  Can someone shed light on this problem because the laptop is only two weeks old?

  Thank you...

  Hello

  To connect the laptop to the WLan, it must ensure that everything is enabled and configured correctly.
  You should check these points:

  -activated the WLan with the WLan switch and the FN + F8
  -don t use any 3rd party config tools WLan if you use the WLan configuration options own Vista
  -for the first test WLan disable the security settings of the Wlan router
  -configure settings to laptop as good SSID and search for your wireless local area network
  -After that the laptop is connected to the WLan router, you can turn back the security settings (encryption, mac address filtering, firewall, etc.)

  Welcome them

• The WRT600N can connect to a wireless access point?

  I installed Windows 7 on my desktop and I was not able to install all types of Linksys wireless adapters.  I decided that linking an my WRT600N wireless access point in the other room and hardwireing the office to the access point, would be a good idea.  I'm probably going to connect it to a Net WTG624 Gear, which is capable of acting as an access point and you connect to another router.  The question is, can the WRT600N you connect to and use the internet and the local access and, ultimately, on the Office of cable?  I feel that it is one of the most stupid questions, I ask myself here again, but I'm not sure.

  EDIT: I'm sure it's called Wireless Bridge.

  Thank you

  Zach

  Hello Zach,

  The WRT600N can connect at the point of access, and vice-versa. I have a WRT600N home and have the same model of NetGear as access point (what are the chances?) and it works fine, although I do miss the 5 GHz as the Access Point is only 2.4 Ghz 802.11 g Standard.

  I hope this helps!

• Impossible to access wifi with other access points

  WNDR4500v3 with firmware V1.0.0. I32

  I bought this router on dec 25 2015 to replace a dead linksys router.
  The router feeds a switch of 16 points from one of the 4 ports.
  I have a win 7 pc connected to one of the other routers 3 ports.
  Then a VoIP connected to port 3 of the router.
  I have 2 other wireless access points connected to the port 16.
  We feed a remote building through a wired connection to the firset access point
  The other access point is also fed by a wired connection.
  The old linksys router had him for 4 years.

  As I said I bought this router as a replacement... but since its worthless and the two wireless access point do not have internet connection.
  So either I get it work or will return it for a refund within 24 hours.

  Figured that out it was Network Manager and windows share the unknown connection of marking.

  In advanved sharing setting I have to change to use for user accounts and passwords to connect to other computers

  Then all the problems went away.

  No more giving up connection and with no internet connection.

• Cannot connect to my Satellite A210 adapter for access point

  Hey everybody...

  I have a little problem with my wireless. We have some books and access point. Everyone can connect to access point except me. I have the Satellite A210-127. Do you know where is the problem? How can I connect to the access point?

  Thank you

  In a first time, you must activate WLAN antenna correctly. Upon first use WLAN switch and set it TO position (the LED will be ON). Next step is to use the FN + F8 key combination. Don't forget THAT WLAN is enabled.

  After this use please ConfigFree radar to see if the access point is visible for your laptop.

• [Wireless-Vista] Disable the automatic access point.

  Right then, I had this problem when you play any kind of online game, what microsoft calls a 'feature', when I play a game online, I get a 5seconds or until disconnecting lag spikes every 1-5 minutes, making it impossible to play counter-strike, Call of Duty Modern Warfare 2, Battlefield 2 and all these sorts of FPS games. I read on this vista of "paintings" Wi - Fi point automatic scan has, so I tried with impatience to deactivate, without success, I even once turned off automatic TCP/IP that crashed my computer, so now I'm wondering, how in the world am I supposed to play a game with spikes of major shift due to a malfunction of the so-called?
  If there is a way to turn it off, remove, or simply work around, tell me. I don't care if it is not allowed, because I got it with feautures of microsoft...

  sckizman,
  Have you ever been able to play games online with this computer?
  What version of Vista and what service pack you have?
  You are able to surf on the net normally or you we lag with almost anything on the internet?
  If you have not yet done so, perform a clean boot , and then test your access.  Also make sure that your system BIOS and chipset drivers are up to date.

  Here are instructions on disabling automatic switching between wireless access points:

  Prevent your computer from switching between wireless access points

  Mike - Engineer Support Microsoft Answers
  Visit our Microsoft answers feedback Forum and let us know what you think.

• can I use a laptop to set up a wifi access point?

  When I first received a laptop of opportunity in last December, a colleague tech at my night school mentioned that I didn't have to buy a 803,11 access point device to plug my switch, but I rather use a WiFi card on my computer to create my own access point. I told him I have such a card and put a little out of my mind.

  However, I have someone outside to spend the night at my place, and he needs to check his e-mail. Unfortunately, it seems that the RJ-45 socket on his laptop is broken, I have tried several cables and impossible to get a connection, including the cable to connect the computer I'm using now.

  Is it possible that I can use ICS on XP Pro (preferred) or Vista 32 bit Home Premium (really want to use it, I have never set the boot loader after the upgrade to XP on a separate partition, especially because XP has worked so much better) to set up enough connectivity for him to connect to the mail server?

  Should I Windows 7 or Vista to do this? I know how to do the reverse quite easily (share Wi-Fi on the Ethernet port), but I don't know how to set up the SSID and others. I would assume same WEP or WPA2 (Yes, I know how it is easy to crack, but it's better that transmitting passwords in clear text because it discourages occasional interception) would too, so it will accept a connection open, unencrypted. I'll just close access once it does.

  How could I go to set it up? I'm not spending money on software that is not free for one night, one-shot deal. Kiss, I just need a connection of bare bones for him. If its Ethernet port was working, I would leave him to plug my switch, but since it's not I need to create a gateway using what material I have on hand, and the only device with any kind of ability 803.11 is my own laptop.

  I know it's possible, I don't know if this is something only Linux, or a solution that requires 3rd party software.

  Yes, you can use ICS.  See http://practicallynetworked.com/sharing/xp_ics/

  I forgot to include this--> http://www.home-network-help.com/ad-hoc-wireless-network.html

  You will need to configure security manually from the properties of maps dialog box wireless (on both computers) and IIRC, you can use WEP in ad-hoc XP networks.

  Go to the correct place
  Right click on the wireless adapter icon and select Properties
  Click the wireless networks tab
  Click Add to create a configuration
  in the 'Association' tab, set the SSID, network authentication 'Open' and WEP data encryption.
  It's been so long that I made that I remember exactly, but I think you can use only the 10 digit Hex key.

• Can E3000 to function as only access Point or should I return it?

  Hi, Ok, I know I acted probably stupid, but I needed to access as a guest of Setup wi - fi which supplied routers LinkSysys. I don't need the router/modem I want to just have a wi - fi access point. I am an advanced user and I can work with manual configuration etc.

  I tried to do a manual installation of the router, I changed the IP, mask of my network and activate the wi - fi and has worked, BUT the guest access option is NOT available unless you use the stupid CISCO connect software.

  Now the cisco connect IS NOT software work or complete installation, if you do not connect through the router and access the Internet, which is IMPOSSIBLE for me to realize that my modem is connected to a firewall device, and we use static DSL PPPoE options and usernameme and password. There is no way I can get cisco doesn't connect to properly charge because it always "fix my connection trying to access the Internet.

  Y at - it any solution on manually properly configure this router and take full advantage of it capabilities or should I return it?

  PS: If the answer is "return" Please do not hesitate to provide me with an alternative that supports the wi - fi access COMMENTS (I do need separate vlan users to a WiFi connection to connect to the internet access BUT WITHOUT HAVING any where on my LAN)

  Thank you very much.

  Best regards, Vassilis

  As I wrote before: it is impossible with the devices that you have...

  The network of comments on the E3000 (and model consumer of any other brand with the same function) only works if the E3000 is your main Internet gateway.

• cannot print wireless to wireless using a but access point wired printing (pc) wireless technology is very well

  I have a HP OfficeJet 8600plus N911a CM749A # product who has problems in this impossible to print wireless to wireless using an access point but Wired print (pc) wireless technology is fine. We have 4 pcs in a network cable that work very well try to print to the printer which is connected wireless. They installed the software and discovered the printer very well. When you try to install the printer on a Win8 Tablet and a laptop Win7 that neither would discover the printer, so I have two devices connected by ethernet cable and ran the facilities in the same way as the PC and installed everything and worked fine. But, after I disconnected the wire and reconnected or the other device wireless again (they go OK so I know that they get an address) when I go to print to the 8600 it says there is no communication to the printer. BTW, I can install (and installed) other (cable) HP printers on the network as the computer laptop and Tablet AUTODECOUVERTS and print... Yes, ideas on why it loses its Wireless communication to the wireless printer. He turns a few odd Protocol or discovered that did not pass on a wireless system?

  Thank you for answering my question and I wanted to know was the brand of the router.  I suggest making sure the router firmware is up to date as well.

  Here is a link to a post I did on the various ports used by HP printers for reference.

  -Incoming and outgoing Ports-

  So all your work computers don't encounter this issue?  Once again, while in the router, verify that wireless isolation is not activated.  A question also, I do not see has anti-anti-virus/firewall you had on your main computer that you are using?  Maybe it's not the cause, but that depends on the software, too.

  -Security and Firewall.

  You have all the exclamation points in your device manager?

  Let me know what is happening when you try another access point.

• configuration cisco air-ap1142n-a-k9 problem wpa2 wireless access point

  HI people,

  I am brand new to Cisco Wireless, just that I bought new wireless access point air-ap1142n-a-k9 cisco, try to configure the configuration of wpa2 for security reason, but impossible to configure in any mode security. So my AP is currently no security / encryption mode.

  Could someone can help and suggest me I will appreciate if I get all documents, so the security problem can be solved.

  Concerning

  Sanjeev

  OK great

  ----------------------------------------------------------------------------------------------------------------------

  Be sure to note the correct answer and mark the thread as answered

• Upgrade license 4402 for additional access Points

  You can apply the L-LIC-WPLUS-25 to a 4402 to enable multiple access points? Or are the 4402 models all locked in their designated access point license?

  Thank you

  -Con

  Hi Con,

  Unfortunately not :(

  The number of support of the AP is "hardcoded" on the WLC model and is not expandable up to 5500 series.

  See you soon!

  Rob

• Unable to connect via the wireless router "problem with wireless adapter or access point" _

  Hello

  I recently replaced my old Toshiba laptop with a new model of Toshiba Satellite L500/033HNX, it installed Windows 7.

  The problem is that I can't connect to my wireless network. I am currently connected via Ethernet cable to my Linksys router.

  I had help from my internet service provider, the installation correctly the problem not because of the connection.

  I had a Linksys online support, the router is a wireless, model - WAG54G ADSL gateway, is not the problem of all the correct settings and other devices can connect via my wireless network. I ran Dr. connectivity several times and it is always impossible to connect, "problem with the wireless adapter or access point.

  OK, you're my next hope to solve the problem can you HELP Please!

  Hi, JoelbX
  I want to thank very you much for your support and effort do to help me solve this problem, but we receive have been, and I don't want to waste any more of your valuable time, so I am the son of closing and deleting of Tring in Microsoft Answers.
  All the best
  Tring

• Unable to connect to wireless internet with error message: "problem with wireless adapter or access point.

  Original title: I am trying to connect to my WiFi.

  I am trying to connect to my wifi but it keep saying there is a "problem with wireless adapter or access point. I tried the steps that he told me to do but still no help.

  Hello

  Thanks for posting your question in the community of Microsoft Windows. I understand that you are facing problems with your wireless internet connection. Correct me if I'm wrong.

  I imagine the inconvenience that you are experiencing. I will definitely help you with this.

  To help you suggest several steps to solve the problem, I would appreciate it if you could answer the following questions:

  1 have you ever done any recent hardware or exchange of software on your computer before the show?

  2. What is the brand and model of the computer?

  Method 1:

  Follow the steps in the link below.

  Of connection problems in Windows wireless and wired network: http://Windows.Microsoft.com/en-us/Windows/help/wired-and-wireless-network-connection-problems-in-Windows

  Method 2:

  Follow the steps in the link below.

  Using the troubleshooter from network in Windows 7:

  http://Windows.Microsoft.com/en-us/Windows7/using-the-network-troubleshooter-in-Windows-7

  Method 3:

  Follow the steps in the link below.

  How can I troubleshoot network card? :

  http://Windows.Microsoft.com/en-us/Windows7/fix-network-adapter-problems

  Your response is very important for us to ensure a proper resolution. Please get back to us with the information above to help you accordingly.

• Of aircraft received fatal alert EUC access point: handshake_failure.

  Hi all

  Does anyone know how to make local CA trusted root to view device Access point (AP)?

  I do a new installation in view of the Horizon and replacement of all the as cottages bookmark for CA certificates signed. Now, I want to deploy AP and it points to a load balancer for the connection view servers. Load balancer and two connection servers all use the same certificate. I put this thumbprint of the certificate to deploy during the FVO AP and AP services begin. But I can't connect to view. In the bundle of newspapers in esmanager.log, I see an error:

  [nioEventLoopGroup-7-1] ERROR utils. SyslogManager: HORIZON_SERVICE:CONNECTION_BROKEN: impossible to interrogate Horizon Broker: javax.net.ssl.SSLException: received fatal alert: handshake_failure

  I did some google-ing and find what "handshake_failure" done often refers to the untrusted root certificate in java keystore. I can even locate java keystore used for the services of the unit, but can not import anything because it is password protected.

  I also tried to register thumbprint of the certificate root during the FVO deploy, but error still in place. I have previously worked for installation of the view with certificates self-signed and everything worked fine (so it probably isn't an installation\configuration error).

  Any ideas? Suggestions? Maybe for device keystore password?

  Thanks in advance,

  Mihhail

  Ok

  My question, my answer.

  Location of the keystore, trust in the EUC access point device is

  / usr/Java/JRE-VMware/lib/security/cacerts

  Keystore password is changeit

  Use keytool-import - trustcacerts-alias alias - file - keystore cacerts file - storepass changeit to import the root certificate. CERT must be X.509 format.

• My Airport Time Capsule can act as a WIRELESS access point

  Hello.

  I brought a Time Capsule with my Mac Pro. It worked well since yesterday.

  I have set up the time Capsule as a WIFI, bypass at my local network access point. There is a router (cable) works at home.

  It's my Mac Pro AirPort Utility and my iPhone, my Time Capsule is displayed with an exclamation point saying "device not found". I can't connect to the disk on this subject by afp share, or smb. Time Machine function is gone too. He failed trying to connect to the share drive from another computer connected to the time Capsule by cable network.

  But at the same time, WiFi works well.

  I tried to recycle energy. Sharing disk will be available. But if I start the Time Machine backup, it will not be a few seconds.

  Any idea?

  Thank you.

  There are several posts here related the issue.

  Luckily, you have set up your new Time Capsule for Back to My Mac (BTMM)?

  If so, the 'temporary' solution is to delete/disable the option of the CCMM, as follows:

  • Run the AirPort Utility.
  • Select the base and then station, select change.
  • On the tab of the Base Station, go back to the section of my Mac at the bottom of the window.
  • If you have entries here, select it and click then the minus sign "-" button to remove it.
  • Click on update and allow the base station restart.

  If you have not enabled CCMM, we have other options for you to try.