configuration cisco air-ap1142n-a-k9 problem wpa2 wireless access point

Similar Questions

• Can I configure Cisco (AIR-CAP1602I-T-K9) 1602i offline?

  Hi everyone, please, I need help here.

  I bought 3 Cisco (AIR-CAP1602I-T-K9) 1602i but I did not buy a controller. How can I configure then offline?

  I saw in other forums, I need to change the IOS software to a stand-alone software. They suggested the ap1g2-k9w7 - tar.152 - 4.JA1.tar. I would like to know if this is the right software and if there is no problem with the license if I download and use it.

  Explanation of the differences between AIR-CAP-1602i-x-K9 e AIR-SAP-1602i-x-K9

  http://community.Spiceworks.com/topic/448208-Cisco-Aironet-1602i-questions-issues

  How to convert standalone IOS

  http://www.experts-exchange.com/Networking/Wireless/Q_28245190.html

  Download IOS:

  http://software.Cisco.com/download/release.html?mdfid=284366503&softwareid=280775090&release=15.2.4-JA1&flowid=37523

  Thank you.

  Wesley

  Hello

  Yes, you must pass in stand-alone mode. Yes, this is the right software and you will not face any problem regarding the license.

  But to download the standalone AP image of cisco, you need a CCO (Cisco connection) and the valid service contract.

  Here is the final image: can download here

  http://software.Cisco.com/download/release.html?mdfid=284366503&flowid=3...

  How to covert to lAP for standalone:

  http://www.YouTube.com/watch?v=QQ_NuxdRhQ4

  http://rscciew.WordPress.com/2014/05/07/access-point-conversion-lap-to-a...

  Concerning

  Remember messages useful rates

• Help AIR-LAP521-G-E-K9 wireless access point

  Hello everyone,

  is there anyone who can give me guidance on how to configure an access point wireless AIR-LAP521-G-E-K9 offline? I tried to connect to a standard 1 GB switch, feed it with an IP via DHCP, it responds to the PING, but when it comes to detect in the CCA (3.1), it says unable to connect without even asking username and/or password. Try to connect to it via HTTP or HTTPS does not work either.

  Perhaps someone could explain to me what I am doing wrong?

  Thanks in advance.

  Stefano.

  Stefano,

  The 521 AP series can operate in light or autonomous mode. If your AP is currently the light image above we can convert by using tftp. (I suspect it does, as shown in light AIR - LAP number while AIR - AP is generally self-contained)

  The best way to check is to check the details of neighbor of cdp for the version of the software AP (or connect to the console of the AP and issue a 'show version').

  If the software has 'k9w7' in the name, which is autonomous. If she has "k9w8" then it is light. When operating in light you will be not able to telnet/ssh or go to the web page of AP.

  To convert your autonomous access point, please follow the procedure described here:

  http://www.Cisco.com/en/us/docs/wireless/access_point/conversion/LWAPP/upgrade/guide/lwapnote.html#wp160918

  -Patrick Croak

  TAC wireless

• Problem with internet access point

  Hello, I saw that this question was asked before, but has never seen a solution to my problem, I will explain:

  I have like 5 months with this problem. I have a TP-LINK 300Mbps Wireless N Router, model No. TL-WR841ND. The fact is that when I plug in my router to the Modem, my wireless network seems to work fine, but when I try to connect to my computer or any other device to the network (mobile phones, playstation 3, tablets, etc.), I am unable to do so. On my laptop, I get the message: 'Problem with wireless adapter or access point', but the most confusing thing is that sometimes I can connect to the Internet via my network wireless without any problem.

  This time I decided to post my problem, because I'm tired of it. Sometimes it happens, sometimes it doesn't. Right now, I have two days without Internet connection (Via router), because my modem works properly.

  PS: I have another router (Linksys) and I can connect to this network, but I want to solve my problem with the TP-Link because the signal is stronger. Help!

  See links.

  How to install a TP-LINK wireless routers (Recommended)?

  http://www.TP-link.com/LK/article/?faqid=92

  Why can I not access the Internet after connecting the TP-LINK router to my modem.

  http://www.TP-link.com/LK/article/?faqid=138

  TP-Link FAQ.

  http://www.TP-link.com/LK/support/FAQ/?keywords=TL-WR841ND

• WRT600N advanced routing problems / use as Access Point and switch

  Firmware 1.01.36 build 4 The WRT600N is connected to an existing LAN and is really only used as a Wireless N access point. There is nothing plugged into the WAN port; only the LAN port. I have NAT disabled. All traffic from a client connected to the WRT600N wireless going very well for the gateway and the Internet router. The customer experience is very good. However, there are a few minor issues as follows.

  1] Setup > Advanced Routing tab has only the following options; to do this, * not * have a picker 'Mode '. NAT, static routing and dynamic routing (RIP).    IS this NORMAL, OR should HAVE a MODE (e.g. switch) AS REFERRED to IN THE HELP FILES?

  [2] even if a connection wireless or wired to the WRT600N works very well, the WRT600N himself is unable to connect to the internet. It cannot connect to NTP to set the time and I can't ping past the gateway router using the ping of the WRT600N diagnostic utility. I ping the gateway 192.168.1.4 port inside, but I can't use the diagnostic the WRT600N ping ping utility something beyond this gateway port. The routing of the WRT600N table is below. THE GATEWAY SHOULD NOT BE 192/168.1.4? HOWEVER THE WRT600N DON'T ME LETS NOT CHANGE IT.

  Destination LAN IP Subnet Mask gateway interface

  192.168.1.0 255.255.255.0 192.168.1.71 LAN & Wireless

  127.0.0.0 255.0.0.0 * LAN & Wireless

  Topic 1. Linksys, used to have a mode option to switch between the modes 'Bridge' and 'router '. The latest routers call it now better NAT power. Gateway mode means THAT NAT is enabled. Router mode means THAT NAT is disabled. The help files are probably a little bit over. But the option is still the same.

  Re 2. It's normal if you use it as only access point (i.e. do not use the WAN port). The router always takes into account that the internet connection via the WAN port, i.e. it will always use the default gateway on the WAN port. If nothing is connected to the WAN port on the router itself has no default gateway and therefore has no access to the internet. Generally, you are not able to establish the default route in either advanced routing page. It is a known limit of these routers if you do not use as a router.

• Access point Cisco does not recognize correctly entered the WPA pre-shared key

  My router is a Cisco DPC/EPC2325 DOCSIS residential gateway with wireless access Point. When connecing to Internet via a wireless adapter, this device does not accept the good WPA pre-shared key. I have no similar problem with another PC. Please notify.

  You mean that you corrected it?
  Great! Thanks for sharing this info with us!

• Cisco suggested cable does not? (Cisco Air-Br1310g-a-k9-R and Ant24120)

  Hello

  I bought 3 Cisco Aironet 1310 Outdoor Access Point/bridge - wireless access point (AIR-BR1310G-A-K9-R ) and 3 Cisco Aironet 2.4 GHz 12 dBi Omni Mast Mount antenna w/RP-TNC connector (AIR-ANT24120) .
  But the antenna cable is very short (1 ft.). so I need a cable extra. I read the newspapers and they said AIR-CAB020LL-R is suggested by cable for ant24120. But when I look at the pictures of this cable I saw this cable has two side RP - TNC female.
  
  
  The access point has the male Ant. side and the next female ANT24120. So, how can I connect this side 2 (MF) with a wire from the female side 2 (FF)? I'm so confused.
  Please can you suggest me a cable to connect this access point to this antenna.
  Thank you very much.

  Hi Bulent,

  This cable has 1 female and 1 male connector

  Intake AIR-CAB020LL-R of interconnection cable low loss of 20 feet, a RP - TNC,.
  one outlet RP - TNC

  http://www.Cisco.com/en/us/prod/collateral/wireless/ps7183/ps469/product_data_sheet09186a008008883b.PDF

  AIR-CAB020LL-R / AIR-CAB050LL-R

  Here are the cables RMT 400 Style with TNC reverse polarity of the connectors at one end and TNC female connector reverse polarity on the other end.

  http://www.coaxplanet.com/CrossReferences/CiscoCrossReference/AIRCAB020LLRAIRCAB050LLR/tabid/265/default.aspx

  See you soon!

  Rob

• PS B110a - wireless configuration will fail if the network has multiple access points

  Photosmart B110a (CN245B) wireless AIO printer.

  I have several wireless access points using the same SSID to provide coverage over a large area. When you install the printer on the screen TouchSmart wireless installation fails. Print report reveals the following error:

  "More than one access point/router wireless was found which matches your network name (SSID). If this is not intended, your HP printer can connect to the wrong network. »

  In my case this IS planned but there seem to be no available option to answer "OK, just connect to any point of access by using my SSID.  If I turn off all but one the APs configuration complete OK. If I have to do every time I turn on the printer the printer is USELESS for me.

  Did I miss something?

  sijomi

  This should not be a problem.  I have a B110 (and another 10 or so HP wireless printers) on a network of airports with 5 access points and they just connect.

  Here are a few suggestions:

  1. don't use WEP - use WPA or WPA2 with a 13 + character password.

  2. enable the SSID broadcast on all access points

  3. do not use the MAC filtering acddress

  4. make sure "AP isolation" or "isolated wireless" is disabled.

  5. make sure that you are not on a private network, virtual, or connected to your network of comments.

  6. If different strings on access points do not work, try the same channel.

• Cisco 1602i series Access point installation

  Hello everyone. I tried to configure cisco AIR-CAP1602i-E-K9 series access point is default for the configuration files and other settings, I guess you are looking for WLC. but I do not have a WLC I want to configure the AP a standalone conceerne Access point. I connected via switch where all the ports on the switch are vlan 10 switch is connected to a router and I have configured the router as DHCP server. It is my first time that I've never touched a cisco point for configuration of access. below is the error that was coming up on the screen countinously when I access the AP via the console. Kindly any assistance in this regard would be highly appreciated. Thank you

  * 00:18:46.324 Mar 1: % 3-CAPWAP-ERRORLOG: could not resolve CISCO-CAPWAP-CONTROLLER
  Not in a bound State.
  * 00:19:31.824 Mar 1: % 3-CAPWAP-DHCP_RENEW: could not find WLC by using DHCP IP. Renew DHCP IP.
  * 00:19:36.828 Mar 1: % 3-CAPWAP-ERRORLOG: event white 38 & combination of State 2.
  * 00:19:36.948 Mar 1: DHCP-6-ADDRESS_ASSIGN %: BVI1 Interface assigned address DHCP 10.10.0.218, mask 255.255.255.0, hostname AP64f6.9dee.87d1

  Translate "CISCO-CAPWAP-CONTROLLER"... the domain server (255.255.255.255)
  * 00:19:42.824 Mar 1: % 3-CAPWAP-ERRORLOG: did not get the server DHCP server log settings.

  * 00:19:51.823 Mar 1: % 3-CAPWAP-ERRORLOG: could not resolve CISCO-CAPWAP-CONTROLLER
  Not in a bound State.
  * 00:20:37.323 Mar 1: % 3-CAPWAP-DHCP_RENEW: could not find WLC by using DHCP IP. Renew DHCP IP.
  * 00:20:42.327 Mar 1: % 3-CAPWAP-ERRORLOG: event white 38 & combination of State 2.
  * 00:20:42.447 Mar 1: DHCP-6-ADDRESS_ASSIGN %: BVI1 Interface assigned address DHCP 10.10.0.219, mask 255.255.255.0, hostname AP64f6.9dee.87d1

  Translate "CISCO-CAPWAP-CONTROLLER"... the domain server (255.255.255.255)
  * 00:20:48.323 Mar 1: % 3-CAPWAP-ERRORLOG: did not get the server DHCP server log settings.

  * 00:20:57.323 Mar 1: % 3-CAPWAP-ERRORLOG: could not resolve CISCO-CAPWAP-CONTROLLER
  Not in a bound State.
  * 00:21:42.822 Mar 1: % 3-CAPWAP-DHCP_RENEW: could not find WLC by using DHCP IP. Renew DHCP IP.
  * 00:21:47.826 Mar 1: % 3-CAPWAP-ERRORLOG: event white 38 & combination of State 2.
  * 00:21:47.946 Mar 1: DHCP-6-ADDRESS_ASSIGN %: BVI1 Interface assigned address DHCP 10.10.0.220, mask 255.255.255.0, hostname AP64f6.9dee.87d1

  Translate "CISCO-CAPWAP-CONTROLLER"... the domain server (255.255.255.255)
  * 00:21:53.822 Mar 1: % 3-CAPWAP-ERRORLOG: did not get the server DHCP server log settings.

  * 00:22:02.822 Mar 1: % 3-CAPWAP-ERRORLOG: could not resolve CISCO-CAPWAP-CONTROLLER
  Not in a bound State.
  * 00:22:48.322 Mar 1: % 3-CAPWAP-DHCP_RENEW: could not find WLC by using DHCP IP. Renew DHCP IP.
  * 00:22:53.326 Mar 1: % 3-CAPWAP-ERRORLOG: event white 38 & combination of State 2.
  * 00:22:53.446 Mar 1: DHCP-6-ADDRESS_ASSIGN %: BVI1 Interface assigned address DHCP 10.10.0.221, mask 255.255.255.0, hostname AP64f6.9dee.87d1

  Translate "CISCO-CAPWAP-CONTROLLER"... the domain server (255.255.255.255)
  * 00:22:59.322 Mar 1: % 3-CAPWAP-ERRORLOG: did not get the server DHCP server log settings.

  * 00:23:08.322 Mar 1: % 3-CAPWAP-ERRORLOG: could not resolve CISCO-CAPWAP-CONTROLLER
  Not in a bound State.
  * 00:23:53.821 Mar 1: % 3-CAPWAP-DHCP_RENEW: could not find WLC by using DHCP IP. Renew DHCP IP.
  * 00:23:58.825 Mar 1: % 3-CAPWAP-ERRORLOG: event white 38 & combination of State 2.
  * 00:23:58.945 Mar 1: DHCP-6-ADDRESS_ASSIGN %: BVI1 Interface assigned address DHCP 10.10.0.222, mask 255.255.255.0, hostname AP64f6.9dee.87d1

  Translate "CISCO-CAPWAP-CONTROLLER"... the domain server (255.255.255.255)

  If you do not have WLC, you will need to convert this access point in stand-alone mode. See below on this post. You must required image before this conversion. If you have a support contract with Cisco you can download from Cisco.com

  https://mrncciew.com/2012/10/20/lightweight-to-autonomous-conversion/

  https://mrncciew.com/2013/12/13/AP-conversion-using-mode-button/

  HTH

  Rasika

  Pls note all useful responses *.

• Problem with SG-200 and access point on VLAN

  I'm having some problems with the configuration of VLANS on the SG-200 and the WiFi access point. The access point (a TP-Link WA801N) is able to access the internet when it is plugged into a port that is on the default VLAN (1 PVID). If I plug it into one of the other VLAN then all clients connected to WiFi to lose access to the internet and can not access on the local VIRTUAL network devices. I've used this configuration with a Cisco WAP4410N of first generation.

  I'm not sure if it's something wrong with the way I configured the switch or a problem with the access point.

  The setup I have is:

  Modem/router ADSL (7800N billion)

  |

  -------------------Port 1--------------------

  |                                               |

  |               SG-200 08 |

  |                                               |

  ---3---port 8 - port

  |                    |

  Access point |

  (TP-Link WA801N).

  |

  SF - 100 D

  The port configurations are

  Port Mode PVID membership

  1 general 1 1U, 7U, 666U

  2 general 1 1U, 7U, 666U

  3 general 7 1U, 7U

  4 General 7 1U, 7U

  5 General 7 1U, 7U

  6 General 7 1U, 7U

  7 general 1U 666, 666U

  8 General 1U 666, 666U

  Iain,

  You have virtual local networks put in place on your router? The subnets that you use on each vlan? The router will give DHCP for each vlan?

  The SG200 isn't a fully managed layer 3 switch, it's just a "smart switch" so you can not actually be able to do simply only switch. A sg300 mode layer 3 would be able to do this because it is a fully managed switch.

  If the router is configured with the VLAN, vlan 1 unidentified, the rest the tag, the router-> SG200 port is trunking and the others as access ports on their vlan respective. Once the router is configured, this video contributor forum albums and Cisco employee David Hornstein is very useful to correctly configure the switch.

  Best,

  David

  Please evaluate the useful messages.

• Problems of wireless with my Satellite A505

  Hello people,

  I have a Satellite A505 which uses a Realtek RTL8191SE wireless network card. Recently, I had connectivity problems with my home router. This configuration used to work perfectly, but recently, I had a problem where I won't be able to connect to my router wireless access point. Reset the adapter does not solve the problem, or don't restart.

  I found that my router reboot solves the problem, I am able to login after the reboot of the router. I have not had this problem on any of the other devices or laptops in my house and never had this problem until last month. I tried to do a factory reset on my router in order to ensure that some recent changes in our setup of the router were not to blame, but the problem persists even with a clean slate.

  Ideas for what to do?

  Thank you!

  Hello

  >... and never had this problem until the last month or more
  Do you use WLAN driver from Toshiba support page?
  I ask this question because I noticed that under Win7 driver for this wireless network card is offered as optional update. Maybe this update is installed, and now you have this problem.
  If possible, try to roll back OS a few weeks back and check if the problem persists.

• WiFi HP ENVY 4500 with several Access Points - same SSIS Configuration

  Hello

  We just got a HP ENVY 4500.  I have a main homenetwork with a wifi Modem/Router and an old router acting as an Access Point to the floor to extend coverage.

  Both have the same SSID and password and are set to different channels.

  My HP ENVY 4500 fails to connect when the Access Point is lit.

  It will connect with it.

  Once connected, I can turn on the PA and all is well.

  The two router an AP using WPA-PSK/WPA2-PSK encriptación

  The router (that it connects to) should have a better sgnal when both are on, so I do not understand why they need the AP to be turned off to connect.

  Any thoughts people?

  Eserim

  I think he has always had problems with several access points.  Try this, what ever AP is closest to the printer, set it to channel 1.  Then try channel 11.  Try now.

• Cannot connect HP D110 to my network using WPA2 wireless

  Hello

  I have a linksys router 160n with two apple airport expresses in bridge DHCP mode.  Each wireless access point's own channel: 1, 6, 11.  They share of SSID and password.  Security is WPA2. I have not activated the MAC filtering. I have multiple and varied devices connected to this network.

  Here's the problem: I can not connect my D110 printer to the network with WPA2 security.

  The printer can connect with security disabled but obviously that is not an option (or just WPA).

  Thus,.

  1) has any related person a D110 printer to a WPA2 wireless network?  If so, how?

  (2) the printer does support WPA2? (no WEP or WPA)

  (3) other tips?

  Thank you!

  OK, some other ideas:

  1. ensure that 802.11 g is turned on.  Other modes may be present, but g must be activated.

  2. change to channel 11 on the main access point (adjust others as required).  I know it's strange, but...

• Problems with internet access, troubleshooting, Windows 7 does not work.

  Hello, I have recently started up to Windows 7 on a partition of Windows 10, because a game wasn't working properly on Windows 10 system (has notified downgrade after a one hour session troubleshooting).

  I don't know if the game is causing these issues or anything else, but my internet connection goes away, even if the internet bar shows that it has internet.

  Right now, I'm typing this, it says I have a problem.

  

  Also, I have troubleshooted a lot of times, with the answer is:

  

  This happens at random, or whenever I join a game for Minecraft.

  Does anyone know the solution to this problem?

  Other images:

  

  Hello

  You can see the answer given by Arya S Asok by mentioning the problem with adapter or wireless access point

  Let us know how it goes.

  Kind regards

• My wifi limited shows, no card wireless for internet access or access point problem

  Hi, I tried to connect with wifi, it shows connected but wrote 'limited' by the side. and below his writings no internet no access. I tried troubleshooting but it says wireless access point or no fixed adapter problem. can sum1 if you please help me with this problem

  Hi Dimma,

  What is the brand and model of your computer?

  This could be caused due to various reasons.

  -Due to the wireless router settings.

  -Due to the IP address.

  Follow the following troubleshooting methods:

  Method 1: I suggest you to reset the wireless router and check if this solves the problem manually.

  Consult the router's manual to know how to manually reset the router.

  Method 2: Reset TCP/IP and check if this solves the problem.

  Follow these steps:

  a. press the Windows key (start screen will popup), type cmd on the right click of the screen prompt, select run as administrator.

  b. at the command prompt, copy and paste (or type) that follows the command, and then press ENTER:
  netsh int ip reset c:\resetlog.txt

  c. Note: If you do not specify a path of the directory for the log file, use the following command:
  netsh int ip reset resetlog.txt

  d. restart the computer.

  
  

  Method 3: If you use WEP encryption change to WPA or WPA 2.

  Hope this helps and let us know if you need help. We will be happy to help you.