Configuration of SNMP ESX51 with esxcli
From the help file:-c |-communities = < str > Set up to ten communities...
and t-|-target = < str > together up to three targets to send SNMPv1 interruptions to.
How can I use more than three communities? I can't understand how to apply more than one community to each target. Thank you
As far as I know, you cannot set specific communities for specific purposes, all communities will be defined for all targets.
Tags: VMware
Similar Questions
-
ISE - unable to get SNMP information with the community
This is the output of the switch when clicking on a switch in authentications followed in ise interface
test2#sh snmp
Chassis: FOC1330W1K0
112 SNMP packets input
0 Bad SNMP version errors
4 Unknown community name
0 Illegal operation for community name supplied
0 Encoding errors
44 Number of requested variables
0 Number of altered variables
44 Get-request PDUs
0 Get-next PDUs
0 Set-request PDUs
0 Input queue packet drops (Maximum queue size 1000)
143 SNMP packets output
0 Too big errors (Maximum packet size 1500)
0 No such name errors
0 Bad values errors
0 General errors
108 Response PDUs
35 Trap PDUs
SNMP global trap: enabled
SNMP logging: enabled
Logging to xxx.xxx.yyy.5.162, 0/10, 7 sent, 0 dropped. (admin/monitoring)
SNMP agent enabled
configuration of snmp:
snmp-server community snmp-com.public RO 33
access-list 3 permit xxx.xxx.kk.0 0.0.0.255
access-list 3 permit xxx.xxx.zz.0 0.0.0.255
access-list 3 permit xxx.xxx.yyy.0 0.0.0.255 (admin/monitoring)
The unknown community name keeps growing when I click on the name of interface switch in ise... any suggestions?
SNMP is configured for the switch added to ise with the name of Community law (v2c - snmp - com.public)
ISE ver 1.1.2.145
Thank you for your help
Currently, Yes, this is a limitation
'public' solves it. So my advice: 'public' set with an ACL restricting EHT nodes only.
-
Hello
I searched many hours today in the internet and your forums, but it seems that this problem is not solved yet:
No writable calendars are configured for the invitations with the provider for Google Calendar.
My Thunderbird is 38.3.0 and the provider for Google Calendar 1.0.4.
I put calendar.google.enableEmailInvitations; true but it did not help. I also tried [email protected]... @googlemail.com. Calendar works fine, it syncs, I see all the entries etc. But I can't accept invitations even IF she must have write access.
What can I do? Is there a solution for this?
Thank you!
DanielUse CalDAV here to access Google Calendar via lightning. I have no experience with the add-on of the provider.
In any case, it is my understanding that you must assign an e-mail address to a calendar in order to be able to accept the invitations for this calendar. I see that in your screenshot.
You can try to remove the Google calendar in lightning and re-create it. Given that all the data is on the server nothing will get lost.
Or you may want to try CalDAV.
https://blog.Mozilla.org/calendar/2013/09/Google-is-changing-the-location-URL-of-their-CalDAV-calendars/ -
Daul Boot Windows XP PRO sp3 and WIN7
I want to have my pc to be a configuration to boot Daul with Windows XP PRO sp3 and WIN7 how?
Hello
Access the link that has a video on how to set up a configuration to dual-boot between Windows XP and Windows 7: http://www.microsoft.com/showcase/en/us/details/ae3108ed-a8a1-4ba3-8698-01b8cedd2cf4
Here's a few that has information on multiboot: can I have multiple operating systems on my computer (multiboot)? : http://windows.microsoft.com/en-US/windows7/Can-I-have-more-than-one-operating-system-on-my-computer-multiboot
Install multiple operating systems (multiboot): http://windows.microsoft.com/en-US/windows7/Install-more-than-one-operating-system-multiboot
-
Configure (fxs) analog phones with Sip trunk
Hi all
IS - this configuration FXS possiple to knit on SIP TRUNK? I HAVE 16 FXS ports and voip gateway 2921 cisco.
Configuring fxs to work with her?
any help thanks.
Is there a PBX at stake here, i.e. CUCM or CME?
In both cases, you have set good dial-peers to point to the FXS ports to match the destination of the SIP trunk, which is pretty simple.
-
Hey guys,.
Can you explain to me - or point me in the direction - where I can be better able to determine the difference between the following keys.
config config enable SNMP traps
config-copy Copy config enable SNMP traps
config-ctid enable SNMP config-ctid traps
config-copy Copy-config enable SNMP trapsThank you
Nik
The trap of the 'config' allows the ciscoConfigManEvent notification, which is triggered when you exit the configuration mode or make a SNMP set.
"Config-copy" and "copy-config" traps are the same on different platforms and activates the ccCopyCompletion trap and fires when a copy of configuring through SNMP operation ends.
The trap of "config-ctid" allows the ccmCTIDRolledOver or ciscoConfigManCTIDNotifyGroup, which seems to be related to the functionality of changing the configuration identifier of follow-up .
-
Configuration of the Kazakh with Bi Publisher fonts
Hi all
Our customer wants to configure the Kazakh fonts with the Bi Publisher.
Is someone could throw some light on this. References to any document metalink will be highly appreciated...
Best regards
gt1942
-External fonts
-Maps of police (for the PDF output)
in http://www.oracle.com/technetwork/middleware/bi-publisher/learnmore/demo-library-toc-173301.html
https://blogs.Oracle.com/XmlPublisher/entry/how_to_install_a_font_using_xm
Administration Oracle Fusion Middleware for Oracle Business Intelligence Publisher Guide
-
Steps of Configuration of SNMP in Oracle 10 g installed on HP - UX
Hello
As I am new to SNMP, please help me by providing the SNMP service installation and configuration steps in Oracle 10 g installed in HP - UX.
I had crossed some of the documents but could not find.
Thanks in advance.Here you are:
Reference guide for the Support of SNMP Enterprise Manager Oracle®
10g Release 2
2 configuration of SNMP for Oraclehttp://download.Oracle.com/docs/CD/B16240_01/doc/EM.102/b16244/Chap2.htm
-
N3024 snmp trouble with openmanage switch.
Hello
I have two new N3024 that I want to manage with openmanage essentials.
I configured N3024 with a name of community and also put in place a notification recipients.The two switches openmanage shows upp under devices.
But they both have a yellow alert on them.
If I try to go to the web interface of openmanage, it takes me to the address 0.0.0.0
Under general / health in the switch I see nothing wrong.
What is the problem?I also try to get the N3024 to send traps.
I have test it with linkup and linkdown.
The newspaper of trap on the switch that I can that a trap is generated but in openmanage nothing comes in.
I have no problem with any other material traps.
Any suggestions on what I am doing wrong?In general the latest firmware has several improvements on the 6.1 firmware SNMP protocol. After the upgrade is done we should test and see if all the problems are solved. If this isn't the case, then we can look in that still does not work.
-
Need urgent help in the configuration of the Client VPN IPSec Site with crossed on Cisco ASA5510 - 8.2 (1).
Here is the presentation:
There are two leased lines for Internet access - a route 1.1.1.1 and 2.2.2.2, the latter being the default Standard, old East for backup.
I was able to configure the Client VPN IPSec Site
(1) with access to the outside so that the internal network (172.16.0.0/24) behind the asa
(2) with Split tunnel with simultaneous assess internal LAN and Internet on the outside.
But I was not able to make the tradiotional model Hairpinng to work in this scenario.
I followed every possible suggestions made on this subject in many topics of Discussion but still no luck. Can someone help me here please?
Here is the race-Conf with Normal Client to Site IPSec VPN configured with no access boarding:
LIMITATION: Cannot boot into any other image ios for unavoidable reasons, must use 8.2 (1)
race-conf - Site VPN Customer normal work without internet access/split tunnel
:
ASA Version 8.2 (1)
!
ciscoasa hostname
domain cisco.campus.com
enable the encrypted password xxxxxxxxxxxxxx
XXXXXXXXXXXXXX encrypted passwd
names of
!
interface GigabitEthernet0/0
nameif outside internet1
security-level 0
IP 1.1.1.1 255.255.255.240
!
interface GigabitEthernet0/1
nameif outside internet2
security-level 0
IP address 2.2.2.2 255.255.255.224
!
interface GigabitEthernet0/2
nameif dmz interface
security-level 0
IP 10.0.1.1 255.255.255.0
!
interface GigabitEthernet0/3
nameif campus-lan
security-level 0
IP 172.16.0.1 255.255.0.0
!
interface Management0/0
nameif CSC-MGMT
security-level 100
the IP 10.0.0.4 address 255.255.255.0
!
boot system Disk0: / asa821 - k8.bin
boot system Disk0: / asa843 - k8.bin
passive FTP mode
DNS server-group DefaultDNS
domain cisco.campus.com
permit same-security-traffic inter-interface
permit same-security-traffic intra-interface
object-group network cmps-lan
the object-group CSC - ip network
object-group network www-Interior
object-group network www-outside
object-group service tcp-80
object-group service udp-53
object-group service https
object-group service pop3
object-group service smtp
object-group service tcp80
object-group service http-s
object-group service pop3-110
object-group service smtp25
object-group service udp53
object-group service ssh
object-group service tcp-port
port udp-object-group service
object-group service ftp
object-group service ftp - data
object-group network csc1-ip
object-group service all-tcp-udp
access list INTERNET1-IN extended permit ip host 1.2.2.2 2.2.2.3
access-list extended SCC-OUT permit ip host 10.0.0.5 everything
list of access CAMPUS-LAN extended permitted tcp 172.16.0.0 255.255.0.0 any eq www
list of access CAMPUS-LAN extended permitted tcp 172.16.0.0 255.255.0.0 any https eq
list of access CAMPUS-LAN extended permitted tcp 172.16.0.0 255.255.0.0 any eq ssh
list of access CAMPUS-LAN extended permitted tcp 172.16.0.0 255.255.0.0 no matter what eq ftp
list of access CAMPUS-LAN extended permitted udp 172.16.0.0 255.255.0.0 no matter what eq field
list of access CAMPUS-LAN extended permitted tcp 172.16.0.0 255.255.0.0 any eq smtp
list of access CAMPUS-LAN extended permitted tcp 172.16.0.0 255.255.0.0 any eq pop3
access CAMPUS-wide LAN ip allowed list a whole
access-list CSC - acl note scan web and mail traffic
access-list CSC - acl extended permit tcp any any eq smtp
access-list CSC - acl extended permit tcp any any eq pop3
access-list CSC - acl note scan web and mail traffic
access-list extended INTERNET2-IN permit tcp any host 1.1.1.2 eq 993
access-list extended INTERNET2-IN permit tcp any host 1.1.1.2 eq imap4
access-list extended INTERNET2-IN permit tcp any host 1.1.1.2 eq 465
access-list extended INTERNET2-IN permit tcp any host 1.1.1.2 eq www
access-list extended INTERNET2-IN permit tcp any host 1.1.1.2 eq https
access-list extended INTERNET2-IN permit tcp any host 1.1.1.2 eq smtp
access-list extended INTERNET2-IN permit tcp any host 1.1.1.2 eq pop3
access-list extended INTERNET2-IN permit ip any host 1.1.1.2
access-list sheep extended ip 172.16.0.0 allow 255.255.0.0 172.16.0.0 255.255.0.0
access list DNS-inspect extended permit tcp any any eq field
access list DNS-inspect extended permit udp any any eq field
access-list extended capin permit ip host 172.16.1.234 all
access-list extended capin permit ip host 172.16.1.52 all
access-list extended capin permit ip any host 172.16.1.52
Capin list extended access permit ip host 172.16.0.82 172.16.0.61
Capin list extended access permit ip host 172.16.0.61 172.16.0.82
access-list extended capout permit ip host 2.2.2.2 everything
access-list extended capout permit ip any host 2.2.2.2
Access campus-lan_nat0_outbound extended ip 172.16.0.0 list allow 255.255.0.0 192.168.150.0 255.255.255.0
pager lines 24
Enable logging
debug logging in buffered memory
asdm of logging of information
Internet1-outside of MTU 1500
Internet2-outside of MTU 1500
interface-dmz MTU 1500
Campus-lan of MTU 1500
MTU 1500 CSC-MGMT
IP local pool 192.168.150.2 - 192.168.150.250 mask 255.255.255.0 vpnpool1
IP check path reverse interface internet2-outside
IP check path reverse interface interface-dmz
IP check path opposite campus-lan interface
IP check path reverse interface CSC-MGMT
no failover
ICMP unreachable rate-limit 1 burst-size 1
ASDM image disk0: / asdm - 621.bin
don't allow no asdm history
ARP timeout 14400
interface of global (internet1-outside) 1
interface of global (internet2-outside) 1
NAT (campus-lan) 0-campus-lan_nat0_outbound access list
NAT (campus-lan) 1 0.0.0.0 0.0.0.0
NAT (CSC-MGMT) 1 10.0.0.5 255.255.255.255
static (CSC-MGMT, internet2-outside) 2.2.2.3 10.0.0.5 netmask 255.255.255.255
Access-group INTERNET2-IN interface internet1-outside
group-access INTERNET1-IN interface internet2-outside
group-access CAMPUS-LAN in campus-lan interface
CSC-OUT access-group in SCC-MGMT interface
Internet2-outside route 0.0.0.0 0.0.0.0 2.2.2.5 1
Route internet1-outside 0.0.0.0 0.0.0.0 1.1.1.5 2
Timeout xlate 03:00
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
dynamic-access-policy-registration DfltAccessPolicy
the ssh LOCAL console AAA authentication
AAA authentication enable LOCAL console
Enable http server
http 10.0.0.2 255.255.255.255 CSC-MGMT
http 10.0.0.8 255.255.255.255 CSC-MGMT
HTTP 1.2.2.2 255.255.255.255 internet2-outside
HTTP 1.2.2.2 255.255.255.255 internet1-outside
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown cold start
Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
Crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac
Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac
Crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac
Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac
Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac
Crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
Crypto ipsec transform-set ESP-AES-128-MD5-esp - aes esp-md5-hmac
life crypto ipsec security association seconds 28800
Crypto ipsec kilobytes of life - safety 4608000 association
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 pfs set group5
Crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 value transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5
Crypto map internet2-outside_map 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP
crypto internet2-outside_map outside internet2 network interface card
Crypto ca trustpoint _SmartCallHome_ServerCA
Configure CRL
Crypto ca certificate chain _SmartCallHome_ServerCA
certificate ca xyzxyzxyzyxzxyzxyzxyzxxyzyxzyxzy
a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as
a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as
a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as
a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as
a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as
a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as
a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as
a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as
a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as
a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as
a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as
a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as
a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as
a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as
a67a897as a67a897as a67a897as a67a897as a67a897as
quit smoking
ISAKMP crypto enable internet2-outside
crypto ISAKMP policy 10
preshared authentication
aes encryption
md5 hash
Group 2
life 86400
Telnet 10.0.0.2 255.255.255.255 CSC-MGMT
Telnet 10.0.0.8 255.255.255.255 CSC-MGMT
Telnet timeout 5
SSH 1.2.3.3 255.255.255.240 internet1-outside
SSH 1.2.2.2 255.255.255.255 internet1-outside
SSH 1.2.2.2 255.255.255.255 internet2-outside
SSH timeout 5
Console timeout 0
a basic threat threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
WebVPN
internal VPN_TG_1 group policy
VPN_TG_1 group policy attributes
Protocol-tunnel-VPN IPSec
username ssochelpdesk encrypted password privilege 15 xxxxxxxxxxxxxx
privilege of encrypted password username administrator 15 xxxxxxxxxxxxxx
username vpnuser1 encrypted password privilege 0 xxxxxxxxxxxxxx
username vpnuser1 attributes
VPN-group-policy VPN_TG_1
type tunnel-group VPN_TG_1 remote access
attributes global-tunnel-group VPN_TG_1
address vpnpool1 pool
Group Policy - by default-VPN_TG_1
IPSec-attributes tunnel-group VPN_TG_1
pre-shared-key *.
!
class-map cmap-DNS
matches the access list DNS-inspect
CCS-class class-map
corresponds to the CSC - acl access list
!
!
type of policy-card inspect dns preset_dns_map
parameters
message-length maximum 512
Policy-map global_policy
CCS category
CSC help
cmap-DNS class
inspect the preset_dns_map dns
!
global service-policy global_policy
context of prompt hostname
Cryptochecksum: y0y0y0y0y0y0y0y0y0y0y0y0y0y
: end
Adding dynamic NAT for 192.168.150.0/24 on the external interface works, or works the sysopt connection permit VPN
Please tell what to do here, to pin all of the traffic Internet from VPN Clients.
That is, that I need clients connected via VPN tunnel, when connected to the internet, should have their addresses IP NAT'ted against the address of outside internet2 network 2.2.2.2 interface, as it happens for the customers of Campus (172.16.0.0/16)
I am well aware of all involved in here, so please be elaborative in your answers. Please let me know if you need more information about this configuration to respond to my request.
Thank you & best regards
MAXS
Hello
If possible, I'd like to see that a TCP connection attempt (e.g. http://www.google.com) in the ASDM logging of the VPN Client when you set up the dynamic NAT for the VPN Pool also.
I'll try also the command "packet - trace" on the SAA, while the VPN Client is connected to the ASA.
The command format is
packet-tracer intput tcp
That should tell what the SAA for this kind of package entering its "input" interface
Still can not see something wrong with the configuration (other than the statement of "nat" missing Dynamics PAT)
-Jouni
-
How to configure pop3 on ipad with iOS 9.3.3 mini mail
How to make the configuration of email pop3 on ipad with iOS 9.3.3 mini
Try the steps in these Apple articles.
Set up an e-mail account on your iPhone, iPad or iPod touch - Apple Support
Get help if you have any questions using a POP email with multiple devices - Apple Support account
-
How to configure TB to work with Filemaker 10?
Hello
Thanks for any help you can offer.
I'm on a Macbookpro on 10.6.8. I want to send e-mails via Filemaker Pro 10.0v1. Thunderbird 31.0 is my default e-mail client. I think I must also configure mac Mail somewhere in this process. These e-mails will be turned off on 5wcw.featheredpipe.com located on the webmail via my Web site. This will complicate things?
Please excuse me if I'm not using correct jargon here - it's new to me. Support FM advises to use Eudora - I hope it's just old info and Thunderbird will work.
Thanks for any help,
Linda
Looks like the real question is how to configure the file creator to work with Thunderbird. Most of the applications like that just use the default mail client. If it does not, you should ask the people to lead Maker how their software works.
-
How do I configure the BlueTooth PAN with Iphone 4 profile?
Hey.
I try to configure PAN on my phone I 4 s.
PAM Apple I Phone taken Bluetooth profiles supported
Using stacked by Toshiba V8.00.12 with bluetooth Toshiba USB micro adapter bluetooth.The Toshiba product manual tells you, if the Bluetooth device supports several functions to run the checkbox custom during the new device synchronization.
So that you can choose the function you want to use.
That's what you do if the manufacturing have set one as the default service and you want to use other services supported!Hello
Found a few nice HowTo on Toshiba BT doc:
+ How do I connect to the internet with the mobile phone via DUN and to share it with the PAN.
http://APS2.toshiba-tro.de/KB0/HTD9602MO0000R01.htmCould be useful...
-
configurations of 2 channels with MCE
I wish I had 2 configurations of channels with MCE. One antenna, the other with satelite. Is it possible to save different configurations and switch from one to another easily?
Hello
I hope I got what you want. :)
AFAIK if you are using a standard antenna you should scan all channels and all available recorded under different program numbers. The use of satellite antenna, you will have to find that a single channel because the channels must be modified on the sat receiver.
You can first connect the antenna and scan all available channels. After that, choose an empty channel and manually configure for sat receiver. Login feature, you can choose and watch your channels. On this way, you can also configure the VHS recorder.
Good bye
-
How to configure the network wireless with an Equium L40-10 X?
Could someone please help?
To configure problems Netgear DG834G wireless router to communicate with my X L40-10. My ISP does not support the Atheros AR5007EG Wireless LAN.
Thank you.
Hello
I can't imagine that it won´t work. Just a few questions:
-Work with the factory-installed system?
-Why Don t you use "Utility Configfree" Toshiba?
-Have you already set on your router and your default machine?
-Could you please give some information about your system and configuration of routers and computers? Can be useful for those who are not standing next to you, and to have physical access to your machine to check what the problem is. :)Maybe you should check these links to see how to connect to a wireless network:
http://compnetworking.about.com/cs/wirelessproducts/a/howtobuildwlan_4.htm
http://articles.TechRepublic.com.com/5100-1035_11-1048162.html
http://www.Microsoft.com/technet/community/columns/cableguy/cg0406.mspxGood luck buddy
See you soon
Maybe you are looking for
-
Apple publishes new IOS 9.3.0.
Hot off the presses. I hope this helps. lder-ios-devices-affected-by-bricking-bu http://9to5Mac.com/2016/03/24/Apple-releases-new-build-of-iOS-9-3-for-users-of-o...
-
which key I press my i mac to watch a dvd
which key is used on my mac i see n inserted the dvd
-
How to turn off the menu of the run time?
I made a menu custom time to run my application, in some situation I want to disable (disable - gray) one of my menu item. How do I...?
-
Vista Service Pack 1 and 2 installation issues
Hello I have to constantly new updates available - which is service pack 2. It takes about 2 seconds to download and says that it is installed-, but it's not. I've tried everything. My system says that I have service pack 1, but if I try to download
-
problem with drivers Windows 7 G7 - 2351ev
I have this laptop: HP Pavilion g7 - 2351ev Product number: D3G14EA #AB7 Unfortunately I can't use Windows 8 for my work, so I wanted to install Windows 7. I managed to find most of the drivers but I had 2 major problems. I cannot find anywhere USB d