Configuration of the net flows on ASR 901 and 902 ASR

Hello

Can you please confirm if the devices ASR 901 and 902 support NetFlow. We want to draw graphs of use for physical but also virtual interfaces on the routers.

ASR 902 IOS:
Cisco IOS XE, Version 03.13.01.S - XR support software

ASR 903 IOS:
Cisco IOS software, software of ASR903 (PPC_LINUX_IOSD-UNIVERSALK9_NPE-M), Version 15.4 (3) S1, VERSION of the SOFTWARE (fc3)

ASR 901 IOS:
Cisco IOS Software, software Version 15.4, 901 (ASR901-UNIVERSALK9-M) (3) S1, VERSION of the SOFTWARE (fc1)

Please advise there at - it another way to do it.

Thanks in advance,

Best regards

Aneesh

Hello

consult the data sheet it resembles that Netflow is not supported.

http://www.Cisco.com/c/en/us/products/collateral/routers/ASR-903-series-...

Anterov

Tags: Cisco Support

Similar Questions

  • Good to know - configuration of the tuner TV G50 in Central and Eastern Europe

    Today I tried the TV tuner of my new G50, and after 2 hours of configuration it works perfectly. I want to share my experience with you.

    The configuration I used: satellite set-top box connected to an old VCR with cable SCART, VCR is connected to the G50 using the coaxial cable supplied with the computer.

    After the establishment of my country (Hungary) and by specifying the string (38) for my cable box, I got perfect sound but the picture of bluish gray with layer of candy red noise levels. Change of the cable or plug another old VCR, same tuning the VCR output channel (37) does not solve the problem. After an hour of reflection, I changed the parameters of location in the United Kingdom and the image finally transformed into bright colors.

    You know, my friends that the Windows Media Center still think here in Central and Eastern Europe that we still live behind the iron curtains and continue to use former SECAM television systems.

    Happy TV!
    Sandor.

    Hi mate

    Thanks for sharing this information with us! It s very useful!

    > The configuration I used: satellite set-top box connected to an old VCR with cable SCART, VCR is connected to the G50 using the coaxial cable supplied with the computer.
    It seems that you got an answer to your first question posted here in this thread.
    http://forums.computers.Toshiba-Europe.com/forums//message.jspa?MessageID=166350
    This beautiful s

    Once again thank you

  • Error message: "Windows cannot start this hardware device because its information of configuration (in the registry) is incomplete or damaged" and dvd burner does not

    Original title: dvd burner does not work can not load the driver

    I get this message "windows cannot start this hardware device because its information of configuration (in the registry) is incomplete or damaged.

    Can someone help me?

    Hi Garry_x,

    1. were you able to use the DVD burner before with no problems?

    2. you remember to make changes to the computer recently?

    This can occur when more than one service is defined for a device, if there is a failure at the opening of the service registry entry, or if the driver name cannot be obtained from the service registry entry.

    You can check out the following link and check for the resolution:

    http://TechNet.Microsoft.com/en-us/library/cc772156 (WS.10) .aspx

    You can also read the following article and check if it helps:

    Your CD or DVD drive is missing or is not recognized by Windows or other programs

    http://support.Microsoft.com/kb/982116

    Hope this information is useful.

  • How to check the system configuration of the SX20 if the touch screen and the remote control does not work

    Hello friends, would like to know how can we access/check the system configuration of the SX20 if we not touch and remote control or they are not in working condition.

    I think that we can check this Switch interface, but unfortunately, I don't have access to the local switch right now.

    Hello

    option is to have access to the local switch and run "show cdp neighbors detail."

    or

    Connect the mobile to PC/computer LAN, run tftpd32 with affected DHCP pool. Then you can login to get the config.

    regds,

    Aman

  • Call the flow of VCS-E and VCS - C

    Hi all

    I'm looking for some documents describing the call flow of VCS-E and VCS - C in H.323 as the jpg I have attached.

    (Especially when endpoint dials on internet to the intranet)

    Are there documents like tthat?

    Best regards

    Kotaro Hashimoto

    Call the stream while VCS - E uses the SANCTION for traversal Protocol (almost identical even use H.460.18 to signal flow).

    Please note that this call flow only not understand key messages each Exchange of messages between VCS & endpoint as well as VCS-E & VCS - C.

  • Configuration of the kit of healthcare on Hyperion Planning 11.1.2.2

    Hello

    I am very new to Hyperion Planning. My main goal is to prepare a demo for the integration of the planning of Hyperion with OBIEE (via Essbase cubes). So, I thought to install and configure the samplecode healthcare kit provided by Oracle. I managed the installation and configuration of the EMP 11.1.2.2 and everything works fine. MY OS is Windows 2008 Server R2 64 bit. But I was struck during the configuration of the application of health care on page 7 of the document provided when he asks:
    * 1. Connect to Oracle Hyperion Enterprise Performance Management workspace as an administrator.* of financial information
    * 2. Select tools, then the database connection Manager.*
    * 3. Create new connections to data source for all types of HCSamp.* plan
    a. connections Essbase pilot
    i. login name: HCSamp.NetRev pointing on request: HCSamp and database: NetRev HCSamp.OpExp pointing to request: HCSamp and database: residential HCSamp.FinStmt pointing on request: HCSamp and database: FinStmt HCSamp.Wrkforce pointing to request: HCSamp and database: Wrkforce
    b. connections pilot planning

    I'm not able to see tools-> database connection manager. Unable to decide where to create the pilot Essbase and planning pilot connections. Any help is appreciated.

    Thank you and best regards,
    Karamba.

    1002398 wrote:
    I'm not able to see the tools--> the database connection manager. Unable to decide where to create the pilot Essbase and planning pilot connections. Any help is appreciated.

    Have you installed RAF and financial information, if so you should be able to connect to the workspace, go to the discovery and then selects the tools-> database connection manager.

    See you soon

    John
    http://John-Goodwin.blogspot.com/

  • Configuration of the SDK software problem

    When installing Flex Builder 3 beta, I installed the SDK in a location not standard (it is the same for the already installed 2.0.1 SDK of Flex Builder 2). Flex Builder 3 is none of them. When I try to manually add (Window-> Preferences-> Flex-> installed Flex SDKS), I get an error message "the page contains invalid values". In Flex Builder 2, the location of the SDK has been configured in < file eclipse > / configuration/com.adobe.flexbuilder/flexbuilder2.xml, Flex Builder 3 does not have this configuration file, so I guess that it relies on a standard location for the SDK.
    -Are there of the workaround to get there (to add software development kits custom)?
    -What is the location of the standard installation of the SDK?

    Thank you
    Peter

    Hi Peter,.

    A few questions:
    -have you installed the Standalone or Plugin of FB 3 version?
    -have you tried to uninstall and then re - install, either to a location standard or standard?

    It is important not to move the location of the SDKs folder tree by default once it is installed, FB is configured by the installer to find that tree and use it as its default global values. You can add your own additional copies of the SDK, in addition to the global default paths, but as if this works only if the default global paths are intact (juicy bug there).

    You can try another miracle solution is changing the file plugins/com.adobe.flexbuilder.flex_*/config.xml, to fix the overall paths which were disconnected on your system.

    I would like to know how this happens,

    C. Agruss
    Flex Builder Team

  • AFTER I CHANGED THE CONFIGURATION IN MY PC FOR WIRE NET IE IS FIREFOX OK NO CONTACT WITH THE NET

    I CHANGED THE NET WITHOUT WIRE-TO-WIRE ON MY PC INTERNET EXPLORER IS OK BUT FIREFOX
    NO CONTACT WITH THE NET HOW TO FIX
    WIN 7

    Firefox cannot load websites but other browsers may

  • To connect to the Net material MKS Alta 1480 mass flow controller

    I have a mass flow controller MKS Alta 1480 (MFC), manual of MFC, Labview 8.2 and the NI PCI - CAN card.  I know that the MFC wired correctly because I can work using another program on the PC that uses the deviceNet interface.  I want to talk to her through Labview.   Everything looks OK Explorer measure.  I have the range OR DNET.  I know that the MACID.  I downloaded the EDS of the manufacturer.

    Here is what I am missing: a general idea on the DeviceNet interface.  Is there a code of example out there that could help me get started?  There are tutorials on how to understand the Dnet Protocol?  I'm used to control serial--> response devices.  I don't know anything about the class, object, attirbutes.

    Thank you

    Joe

    Normal 0

    Joe, you can read the MFC object sensor analog-S Flow value.

    Class Id 49 0 x (31), Instance Id 1 (0x01), attribute Id 6 (0x06)

    The default data Type is integer and units of data's counties

    Normal 0 if you want the reading of the assembly object, you're going to have establish polled i/o connection, then read DeviceNet IO.vi allows you to read feeds.

  • DirectSound Init failed? __Failed to get the Configuration of the speakers?

    I have redownloaded Flyff recently on my computer and when I run the program two pop ups saying:

    DirectSound Init failed
    Failed to get the Configuration of the speakers

    I have redownloaded Direct Sound / DirectSDK

    but he still appears and speaker configuration?

    I don't know what it is.

    But after that strays and I click ok at the same time need me the sign in the screen of the user.  Everything is slowed down a lot, but at least maybe 30 seconds for the text is displayed.

    Then after that it takes forever to get on and as soon as I did, nothing is moving.

    The internet is fine, so there must be something with the computer.  But what?

    Can someone help me please?

    Hello

    ·                    What version of Windows is installed on your computer?

    If you use Windows 7, there is no information if it is compatible with Windows 7. The money given the link provides the same information.

    http://www.Microsoft.com/Windows/compatibility/Windows-7/en-us/details.aspx?type=software&p=Flyff&v=Gala-NET%2c%20Inc.&UID=&l=en&pf=0&PI=0&s=Flyff&OS=64-bit

    You try to run the program in compatibility mode and check if that helps. Follow the link given below to run the troubleshooter for compatibility.

    Make older programs in this version of Windows

    http://Windows.Microsoft.com/en-us/Windows7/make-older-programs-run-in-this-version-of-Windows

    If you do not use Windows 7, you can perform a system restore and try to reinstall the game. Before reinstalling the game, set up your computer in a clean boot state, then continue to check if there is no conflict with the installation of the touch pack software while the installation process. To set up its own start-up follow the link below.

    How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7

    http://support.Microsoft.com/kb/929135

    Note: Once you have finished installing, follow step 7 article to start on normal startup.

    Hope this information is useful.

    Amrita M

    Microsoft Answers Support Engineer
    Visit our Microsoft answers feedback Forum and let us know what you think.

  • Computer is located in a loop of reboot installation update to the configuration of the stage on Windows Vista updates

    problem with the configuration of updates on windows vista - endless loop - no way out

    like many before me, I can't start my computer because windows update has got stuck to the configuration. When I try safe mode, it ends up with screen-cant even get on the system of repair-naoual the same loop. No one at microsoft knows the answer to this >

    You need to start on the Startup Repair disk or recovery Manufacturer'e disk/s.

    Follow these steps to try to solve your problems of boot.

     

    Restore point:

    http://www.howtogeek.com/HOWTO/Windows-Vista/using-Windows-Vista-system-restore/

    Do Safe Mode system restore, if it is impossible to do in Normal Mode.

    Try typing F8 at startup and in the list of Boot selections, select Mode safe using ARROW top to go there > and then press ENTER.

    Try a restore of the system once, to choose a Restore Point prior to your problem...

    Click Start > programs > Accessories > system tools > system restore > choose another time > next > etc.

    http://www.windowsvistauserguide.com/system_restore.htm

    Read the above for a very good graph shows how backward more than 5 days in the System Restore Points by checking the correct box.

    ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

     

    If the system or Mode restore safe work not and you do not have a Microsoft Vista DVD, make a repair disc to do a Startup Repair:

    Download the ISO on the link provided and make a record of repair time it starts.

    Go to your Bios/Setup, or the Boot Menu at startup and change the Boot order to make the DVD/CD drive 1st in the boot order, then reboot with the disk in the drive.

    At the startup/power on you should see at the bottom of the screen either F2 or DELETE, go to Setup/Bios or F12 for the Boot Menu.

    When you have changed that, insert the Bootable disk you did in the drive and reboot.

    http://www.bleepingcomputer.com/tutorials/tutorial148.html

    Link above shows what the process looks like and a manual, it load the repair options.

    NeoSmart containing the content of the Windows Vista DVD 'Recovery Centre', as we refer to him. It cannot be used to install or reinstall Windows Vista, and is just a Windows PE interface to recovering your PC. Technically, we could re-create this installation with downloadable media media freely from Microsoft (namely the Microsoft WAIK, several gigabyte download); but it is pretty darn decent of Microsoft to present Windows users who might not be able to create such a thing on their own.

    Read all the info on the website on how to create and use:

    http://NeoSmart.net/blog/2008/Windows-Vista-recovery-disc-download/

    ISO Burner:http://www.snapfiles.com/get/active-isoburner.html

    It's a very good Vista startup repair disk.

    You can do a system restart tool, system, etc it restore.

    It is NOT a disc of resettlement.

    And the 32-bit is what normally comes on a computer, unless 64-bit.

    See you soon.

    Mick Murphy - Microsoft partner

  • I get an error msg saying dat "generic host for win32 services has encountered a probem n must be closed" after a certain time when I use the net

    whenever I run internet with my modem wireless to my lappy, after 5-10 min.or it displays a msg "generic host process for win32 has encountered a problem and needs to close" and sometimes my connction aftr net stops.i have windows xp Service Pack 2 operating system.i have followed all the steps shown on your site, but still yhe problem persists.wht should I do? This is troubling me a lot. I also downloaded windows xp-KB894391 - x 86 - ENU.exe, but it has no effect.

    Hi Candice Michelle,.

    Have you done a recent software or hardware changes to the system?

    Since you face after downloading the KB894391, you can try the following steps and check if it helps:

    Method 1:

    You can try to reset WinSock and check if it helps:

    How to determine and to recover from Winsock2 corruption in Windows Server 2003, Windows XP and Windows Vista

    Note: The article mentioned above contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, see the article:

    How to back up and restore the registry in Windows

    Method 2:

    You can refer to the computer or the device manufacturer's Web site and try to install the latest version of the drivers for the wireless card and check if it helps:

    How to manage devices in Windows XP

    Method 3:

    You can try to perform a clean boot and check if it helps.

    A clean boot to check if startup item or services to third-party application is causing this issue.

    How to configure Windows XP to start in a "clean boot".

    Note: Make sure that you put the computer to a Normal startup once you have completed troubleshooting.

  • When I try to connect to the net on my laptop LG I often get the message saying that windows could not connect.

    Windows does not remember the setting.

    When I try to connect to the net on my laptop LG I often get the message saying that windows could not connect and I have to go into the advanced settings and check the box that says allow windows to configure the network. My problem is that windows doesn't remember this setting and that I need to check the box almost everytime I try to connect. He made it with my desktop so I was wondering if anyone has a solution for this.

    Using a wireless router? What is the brand and model of your router? I don't think it's a matter of windows.

    Troubleshooting in windows wireless network connection problems

    http://Windows.Microsoft.com/en-us/Windows/help/wireless-network-connection-problems-in-Windows

    Hope this helpful. Post back if your problem is not resolved in the link above.

  • Is there a documentation about the configuration of the function keys (program)

    Is there a documentation about the configuration of the function keys (program).

    Dell Dimension 1400, model XP SK8110 keyboard.   Yes, I know there are 7 years old, but running like a champ.

    Hello

    You can use various function keys to activate certain features and commands only. The following list details the current functions keys, what they do, and when you can use them.

    Three keys can be used when Setup is loading and when you are prompted to press the F6 function key to install some third-party small computer system interface () SCSI and host controller drivers:

    • F5 - for computer type or hardware abstraction layer (HAL) selection
    • F6 - to install the SCSI controller drivers and third-party host
    • F7 - to run Setup without Advanced Configuration and Power Interface (ACPI)

    When the "Welcome" screen is displayed, the following function keys can be used:

    • F2 - to automatically start the process (ASR, Automated System Recovery).
    • F10 - to bypass the menu screens and to load the Recovery Console

    During the GUI (GUI) - Mode Setup, the following function keys can be used:

    • SHIFT + F10 - to enable access to a prompt during the installation in graphical Mode
    • SHIFT + F11 - to display "old" wizards that give more detail.

    Thus, it is not possible to configure the function keys to perform this task. However, you can use your favorite search engine to perform this task.

    Warning: Using third-party software, including hardware drivers can cause serious problems that may prevent your computer from starting properly. Microsoft cannot guarantee that problems resulting from the use of third-party software can be solved. Software using third party is at your own risk.

  • WiFi is connected but I can't connect to the net, what to do?

    WiFi is connected but I can't connect to the net, what to do?

    Hi Torrespa,

    1. what happens when you try to connect to the internet?

    2. were you able to use the Wi - Fi connection earlier?

    3. what brand & model of network card?

    You can follow this link & check if the problem persists:

    How to fix wireless network connections in Windows XP Service Pack 2?


    Reference:
    Wired and wireless in Windows network connection problems

     To set up automatic wireless network configuration

    Hope the helps of information.

Maybe you are looking for

  • Why take control of camera

    Why should I activate the control of my phone camera to install Firefox?

  • Computer hangs when installing bluetooth driver

    Hello I bought a bluetooth USB dongle with toshiba bluetooth software. The installation hangs at the end of the driver installation progress bar. I use Windows XP c. 5.1 SP2. Comm ports currently in use are 1,2,3,5 and one called 'BT Port' (COM65) wh

  • XP sp1 Offline Installer

    where can I get xp sp1a Offline Installer? Please help, please. Thanks in advance

  • The volume control does not work in the ASUS laptop with the keyboard

    Original title: my speaker works well but y I can't control the volume when I press Fn + F10 F11 or F12 I juz bought the computer for 1 week... it's asus brand... now I nest click to control the volume, because my keyboard cannot control there is no

  • Questions of calendar/appointment of blackBerry Smartphones

    On my 8330, when you view an appointment, it is more an option for me at the 'use to send' where I can send the appointment to another person, or even another user BBM.  I checked under my services by default, and the calendar is not listed, it (the