Configuration VPN Cisco RV110W.

Hello

We have a new RV100W router. I would like to use it for iPhone, PC and MAC for you connect via IPSec (QuickVPN) or PTTP.

Whenever I go to the VPN configuration, it tells me that I need to set up a 10.x.x.1 network. How can I use VPN without doing?

Thank you!

Hi bndbrennan,

Try to change the IP address, set up your VPN clients, and then restore the IP 192.168.1.1. The reason for which the router wants to change is because there are so many routers out there that have 192.168.1.1. If you always try to connect from one of these routers, the connection will fail. We see a lot of people that use 192.168.2.1 and it works fine.

Tags: Cisco Support

Similar Questions

  • LT2P configuration vpn cisco asa with the internet machine windows/mac issue

    Dear all,

    I have properly configured configuration vpn L2TP on asa 5510 with 8.0 (4) version of IOS.

    My internet does not work when I connect using the vpn. Even if I give power of attorney or dns or I remove the proxy

    It does not work. only the resources behind the firewall, I can access. I use the extended access list

    I tried also with the standard access list.

    Please please suggest what error might be.

    Thank you

    JV

    Split for L2TP over IPSec tunnel tunnel is not configured on the head end (ASA), it must be configured on the client itself, in accordance with the following Microsoft article:

    http://TechNet.Microsoft.com/en-us/library/bb878117.aspx

  • VPN CISCO RV110W fail.

    Hello

    I have a router Aztech DSL1015EW (S) and Cisco RV100w. Here's my setup.

    Phone - RJ11---> DSL1015EW (S) - RJ45---> RV110W

    -J' tried to build the portable computer remote VPN connection to RV110W (failed)

    -Also failefk quick VPN

    -PPTP failed

    Port forwarding on DSL1015EW

    I don't have the public ip address

    I use dydns.

    What can I do? Please help me.

    Fast VPN error message is "bridge not answer do you expect ot.

    PPTP error code is cannot estiblishe to the remote host.

    Hello

    Hi, thank you for using our forum, my name is Johnnatan I left the community of support to small businesses.

    I apologize for your stress, in this case I advise you to check this link with useful information about the VPN fast https://supportforums.cisco.com/docs/DOC-29399

    I hope you find this answer useful,

    "* Please mark the issue as response or write it down so others can benefit from.

    Greetings,

    Johnnatan Rodríguez Miranda.

    Support of Cisco network engineer.

  • Configuration VPN Cisco ASA5505 new 800

    I have 2 office buildings using routers Cisco 800 series with a L2L VPN between the two.  I'm upgrading from the router to an ASA5505 at one of the offices but cannot understand the L2L VPN on the SAA.  Specifically, may not know how to set the pre-shared key.  On the Cisco 800 there:

    ISAKMP crypto key address

    This doesn't seem to work on the SAA.  Can anyone help this?  Here is my current config on the Cisco 800...

    crypto ISAKMP policy 10

    BA 3des

    md5 hash

    preshared authentication

    Group 2

    ISAKMP crypto key

    address

    !

    !

    Crypto ipsec transform-set esp-3des esp-md5-hmac DUMAC3

    Crypto ipsec df - bit clear

    !

    MYmap 10 ipsec-isakmp crypto map

    defined by peer 75.148.153.217

    Set security-association second life 36000

    game of transformation-DUMAC3

    match address 101

    access-list 101 permit ip 192.168.1.0 0.0.0.255 192.168.7.0 0.0.0.255

    in your crypto-maps, the '10' and '65535' are the sequence numbers. A CM handset might look like this:

    address for correspondence primaryisp_map 10 101 crypto card

    peer set card crypto primaryisp_map 10 99.119.80.165

    primaryisp_map 10 set transform-set DUMAC3 ikev1 crypto card

    primaryisp_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP

    card crypto primaryisp_map interface primaryisp

  • Cisco RV110W supports up to 1 VPN policies

    Best regards

    I use a router Cisco RV110W to 20 natoinwide of branches with a central site for interconnection, however, although VPN correctly between a branch and the central location it is not possible to add another tunnel in the RV110W to another secondary site (see photo)

    In the data sheet RV110W it is said that this router supports up to 5 VPN tunnels, but apparently these 5 tunnels are supposed to establish via the software QuickVPN from a computer.

    so: is there a real limit to VPN site to site (router to router) 1 with RV110W?

    Thanks in advance for any help!

    Please contact Cisco,

    The RV110w supports only 1 site to tunnel

    Of the data sheet:

    1 tunnel IPSec Site to Site

    The RV130W will allow 10 site to site tunnels, datasheet below:

    http://www.Cisco.com/c/en/us/products/collateral/routers/small-business-...

    Best regards

  • Cisco 1921 - how to configure VPN multiple Tunnels to AWS

    I have a router VPN Cisco 1921. I managed to create tunnel VPN Site to Site with AWS VPN Tunnel 1. AWS offers 2 tunnels, so I created another card Crypto and attaches to the existing policy. But the 2nd tunnel won't come. I don't know what I'm missing... is there a special setup that needs to be done to allow multiple IPsec vpn tunnels on the same physical interface? I have attached a picture and included the configuration of my router, if it helps.

    C1921 #sh run
    Building configuration...

    Current configuration: 2720 bytes
    !
    ! Last configuration change at 02:12:54 UTC Friday, may 6, 2016, by admin
    !
    version 15.5
    horodateurs service debug datetime msec
    Log service timestamps datetime msec
    encryption password service
    !
    hostname C1921
    !
    boot-start-marker
    boot-end-marker
    !
    !
    logging buffered 52000
    enable secret 5 $1$ jc6L$ uHH55qNhplouO/N5793oW.
    !
    No aaa new-model
    Ethernet lmi this
    !
    !
    !
    !
    !
    !
    !
    !
    !
    !
    !
    !
    Research of IP source-interface GigabitEthernet0/1 domain
    IP cef
    No ipv6 cef
    !
    Authenticated MultiLink bundle-name Panel
    !
    !
    !
    license udi pid CISCO1921/K9 sn FTX1845F03F
    !
    !
    username admin privilege 15 password 7 121A0C041104
    paul privilege 0 7 password username 14141B180F0B
    !
    redundancy
    !
    !
    !
    !
    !
    !
    !
    crypto ISAKMP policy 10
    BA aes
    preshared authentication
    Group 2
    lifetime 28800
    ISAKMP crypto keys secret1 address 52.35.42.787
    ISAKMP crypto keys secret2 address 52.36.15.787
    !
    !
    Crypto ipsec transform-set AWS - VPN aes - esp esp-sha-hmac
    tunnel mode
    !
    !
    !
    map SDM_CMAP_1 1 ipsec-isakmp crypto
    Description Tunnel 1 to 52.35.42.787
    defined by peer 52.35.42.787
    game of transformation-AWS-VPN
    PFS group2 Set
    match address 100
    map SDM_CMAP_1 2 ipsec-isakmp crypto
    Description 2 to 52.36.15.787 Tunnel
    defined by peer 52.36.15.787
    game of transformation-AWS-VPN
    PFS group2 Set
    match address 100
    !
    !
    !
    !
    !
    the Embedded-Service-Engine0/0 interface
    no ip address
    Shutdown
    !
    interface GigabitEthernet0/0
    Description connection Wan WAN - ETH$
    IP address 192.168.1.252 255.255.255.0
    automatic duplex
    automatic speed
    map SDM_CMAP_1 crypto
    !
    interface GigabitEthernet0/1
    Description of the connection to the local network
    IP 192.168.0.252 255.255.255.0
    automatic duplex
    automatic speed
    !
    IP forward-Protocol ND
    !
    IP http server
    local IP http authentication
    no ip http secure server
    IP http timeout policy slowed down 60 life 86400 request 10000
    !
    IP route 0.0.0.0 0.0.0.0 192.168.1.254 permanent

    !
    recording of debug trap
    host 192.168.0.3 record
    host 192.168.0.47 record
    !
    !
    Note access-list 100 permit to AWS Tunnel 1
    Access-list 100 CCP_ACL category = 20 note
    access-list 100 permit ip 192.168.0.0 0.0.0.255 any what newspaper
    Note access-list 101 permit to AWS Tunnel 2
    Note access-list 101 category CCP_ACL = 4
    access-list 101 permit ip 192.168.0.0 0.0.0.255 any logexit
    !
    control plan
    !
    !
    alias con exec conf t
    SIB exec show int short ip alias
    alias exec srb see the race | b
    sri alias exec show run int
    !
    Line con 0
    exec-timeout 0 0
    Synchronous recording
    line to 0
    line 2
    no activation-character
    No exec
    preferred no transport
    transport output pad rlogin lapb - your MOP v120 udptn ssh telnet
    StopBits 1
    line vty 0 4
    privilege level 15
    local connection
    transport of entry all
    transportation out all
    !
    Scheduler allocate 20000 1000
    !
    end

    There should be no second tunnel.

    I use either a peer or the other, but not both at the same time.

    To display both at the same time, you need to use the Tunnel interfaces.  Amazon would have you sent pretty much the exact commands to copy and paste into.

  • Configure the Cisco VPN client to pass through the VPN site-to-site (GUI)

    Hello

    I say hat the chain and responses I've seen to achieve this goal have been great...

    https://supportforums.Cisco.com/discussion/12234631/Cisco-ASA-5505-VPN-p...

    and

    https://supportforums.Cisco.com/document/12191196/AnyConnect-client-site...

    My question is "we will get this configuration by using the graphical user interface for someone who is not notified about the command line?"

    Thank you

    Of course, all this can be configured via ASDM.

    Looking at the second example you posted above, they point you first change:

    ACL split of the tunnel for the AnyConnect customer

    This Configuration > remote access VPN > network (Client) access > AnyConnect connection profile > (chose the profile and select Edit) > (choose "Manage" next to group policy) > Edit > advanced > Split Tunneling > ensure that the policy does not "Inherit" but rather "Tunnel network list below" > Unselect "Inherit" next to the network list, then 'manage '. Enter your networks you want in the GUI in this dialog box. Click OK all the way back to the main window ASDM and click on apply.

    You then change:

    Crypto ACL for the tunnel from Site to Site

    To do this, go to Configuration > VPN Site-to_site > connection profiles > (choose your profile and select edit) > add the VPN client address pool to the list of local network between protect networks. Yet once, click OK all the way back to the main window ASDM and click on apply.

    Then, allow the

    ASA to redirect back on the same interface traffic it receives

    .. is defined under Configuration > Device Setup > Interfaces. (check the box at the bottom of this screen). Click on apply

    Finally, there is the NAT exemption. For which go to Configuration > firewall > rules NAT. Add a NAT device rule before rules network object with Interface Source out, Source address your address pool VPN, the Destination address to include remote subnets and Action is Static Source NAT type source address and destination address remaining as original (i.e. without NAT). Once on OK all the way back to the main window ASDM and click on apply. Save and test.

    Good luck. Don't forget to note the brand and posts useful when your question is answered.

  • Another problem with the configuration of Cisco VPN Client access VPN Site2site

    We have a Cisco ASA 5505 at our CORP. branch I configured the VPN Site2Site to our COLO with a Juniper SRX220h, to another site works well, but when users access the home Cisco VPN client, they cannot ping or SSH through the Site2Site.  JTACS contacted and they said it is not on their end, so I tried to contact Cisco TAC, no support.  So here I am today, after for the 3 days (including Friday of last week) of searching the Internet for more than 6 hours per day and try different examples of other users. NO LUCK. The VPN client shows the route secure 10.1.0.0

    Sorry to post this, but I'm frustrated and boss breathing down my neck to complete it.

    CORP netowrk 192.168.1.0

    IP VPN 192.168.12.0 pool

    Colo 10.1.0.0 internal ip address

    Also, here's an example of my config ASA

    : Saved

    :

    ASA Version 8.2 (1)

    !

    hostname lwchsasa

    names of

    name 10.1.0.1 colo

    !

    interface Vlan1

    nameif inside

    security-level 100

    IP 192.168.1.1 255.255.255.0

    !

    interface Vlan2

    backup interface Vlan12

    nameif outside_pri

    security-level 0

    IP 64.20.30.170 255.255.255.248

    !

    interface Vlan12

    nameif backup

    security-level 0

    IP 173.165.159.241 255.255.255.248

    !

    interface Ethernet0/0

    switchport access vlan 2

    !

    interface Ethernet0/1

    switchport access vlan 12

    !

    interface Ethernet0/2

    !

    interface Ethernet0/3

    !

    interface Ethernet0/4

    !

    interface Ethernet0/5

    !

    interface Ethernet0/6

    !

    interface Ethernet0/7

    !

    passive FTP mode

    permit same-security-traffic inter-interface

    permit same-security-traffic intra-interface

    object-group network NY

    object-network 192.168.100.0 255.255.255.0

    BSRO-3387 tcp service object-group

    port-object eq 3387

    BSRO-3388 tcp service object-group

    port-object eq 3388

    BSRO-3389 tcp service object-group

    EQ port 3389 object

    object-group service tcp OpenAtrium

    port-object eq 8100

    object-group service Proxy tcp

    port-object eq 982

    VOIP10K - 20K udp service object-group

    10000 20000 object-port Beach

    the clientvpn object-group network

    object-network 192.168.12.0 255.255.255.0

    APEX-SSL tcp service object-group

    Description of Apex Dashboard Service

    port-object eq 8586

    object-group network CHS-Colo

    object-network 10.1.0.0 255.255.255.0

    the DM_INLINE_NETWORK_1 object-group network

    object-network 192.168.1.0 255.255.255.0

    host of the object-Network 64.20.30.170

    object-group service DM_INLINE_SERVICE_1

    the purpose of the ip service

    ICMP service object

    service-object icmp traceroute

    the purpose of the service tcp - udp eq www

    the tcp eq ftp service object

    the purpose of the tcp eq ftp service - data

    the eq sqlnet tcp service object

    EQ-ssh tcp service object

    the purpose of the service udp eq www

    the eq tftp udp service object

    object-group service DM_INLINE_SERVICE_2

    the purpose of the ip service

    ICMP service object

    EQ-ssh tcp service object

    inside_nat0_outbound to access ip 192.168.1.0 scope list allow 255.255.255.0 clientvpn object-group

    inside_nat0_outbound to access ip 192.168.1.0 scope list allow 255.255.255.0 object-group NY

    inside_nat0_outbound to access ip 192.168.1.0 scope list allow 255.255.255.0 object-group CHS-Colo

    inside_nat0_outbound list of allowed ip extended access any 192.168.12.0 255.255.255.0

    outside_pri_1_cryptomap to access ip 192.168.1.0 scope list allow 255.255.255.0 object-group NY

    outside_pri_access_in list extended access permit tcp any interface outside_pri eq www

    outside_pri_access_in list extended access permit tcp any outside_pri eq https interface

    outside_pri_access_in list extended access permit tcp any interface outside_pri eq 8100

    outside_pri_access_in list extended access permit tcp any outside_pri eq idle ssh interface

    outside_pri_access_in list extended access permit icmp any any echo response

    outside_pri_access_in list extended access permit icmp any any source-quench

    outside_pri_access_in list extended access allow all unreachable icmp

    outside_pri_access_in list extended access permit icmp any one time exceed

    outside_pri_access_in list extended access permit tcp any 64.20.30.168 255.255.255.248 eq 8586

    levelwingVPN_splitTunnelAcl list standard access allowed 192.168.1.0 255.255.255.0

    levelwingVPN_splitTunnelAcl list standard access allowed 10.1.0.0 255.255.255.0

    outside_pri_cryptomap to access ip 192.168.1.0 scope list allow 255.255.255.0 object-group CHS-Colo

    backup_nat0_outbound list extended access allowed object-group DM_INLINE_NETWORK_1 192.168.12.0 ip 255.255.255.0

    outside_pri_cryptomap_1 list extended access allow DM_INLINE_SERVICE_2 of object-group 192.168.1.0 255.255.255.0 10.1.0.0 255.255.255.0

    outside_19_cryptomap to access extended list ip 192.168.12.0 allow 255.255.255.0 10.1.0.0 255.255.255.0

    inside_nat0_outbound_1 to access ip 192.168.1.0 scope list allow 255.255.255.0 object-group CHS-Colo

    VPN-Corp-Colo extended access list permits object-group DM_INLINE_SERVICE_1 192.168.12.0 255.255.255.0 10.1.0.0 255.255.255.0

    Note to OUTSIDE-NAT0 NAT0 customer VPN remote site access-list

    OUTSIDE-NAT0 192.168.12.0 ip extended access list allow 255.255.255.0 10.1.0.0 255.255.255.0

    L2LVPN to access extended list ip 192.168.12.0 allow 255.255.255.0 10.1.0.0 255.255.255.0

    pager lines 24

    Enable logging

    debug logging in buffered memory

    exploitation forest asdm warnings

    record of the rate-limit unlimited level 4

    destination of exports flow inside 192.168.1.1 2055

    timeout-rate flow-export model 1

    Within 1500 MTU

    outside_pri MTU 1500

    backup of MTU 1500

    local pool LVCHSVPN 192.168.12.100 - 192.168.12.254 255.255.255.0 IP mask

    no failover

    ICMP unreachable rate-limit 100 burst-size 5

    ICMP allow any inside

    ICMP allow any outside_pri

    don't allow no asdm history

    ARP timeout 14400

    NAT-control

    interface of global (outside_pri) 1

    Global 1 interface (backup)

    NAT (inside) 0-list of access inside_nat0_outbound

    NAT (inside) 0 inside_nat0_outbound_1 list of outdoor access

    NAT (inside) 1 0.0.0.0 0.0.0.0

    NAT (outside_pri) 0-list of access OUTSIDE-NAT0

    backup_nat0_outbound (backup) NAT 0 access list

    static TCP (inside outside_pri) interface https 192.168.1.45 https netmask 255.255.255.255 dns

    static TCP (inside outside_pri) interface 192.168.1.45 www www netmask 255.255.255.255 dns

    static TCP (inside outside_pri) interface 8586 192.168.1.45 8586 netmask 255.255.255.255 dns

    static (inside, inside) tcp interface 8100 192.168.1.45 8100 netmask 255.255.255.255 dns

    Access-group outside_pri_access_in in the outside_pri interface

    Route 0.0.0.0 outside_pri 0.0.0.0 64.20.30.169 1 track 1

    Backup route 0.0.0.0 0.0.0.0 173.165.159.246 254

    Timeout xlate 03:00

    Conn Timeout 0:00:00 half-closed 0:30:00 udp icmp from 01:00 0:00:02

    Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00

    Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00

    Timeout sip-provisional-media 0:02:00 01:00 uauth uauth absolute inactivity from 01:00

    timeout tcp-proxy-reassembly 0:01:00

    dynamic-access-policy-registration DfltAccessPolicy

    AAA authentication enable LOCAL console

    AAA authentication http LOCAL console

    the ssh LOCAL console AAA authentication

    http server enable 981

    http 192.168.1.0 255.255.255.0 inside

    http 0.0.0.0 0.0.0.0 outside_pri

    http 0.0.0.0 0.0.0.0 backup

    SNMP server group Authentication_Only v3 auth

    SNMP-server host inside 192.168.1.47 survey community lwmedia version 2 c

    No snmp server location

    No snmp Server contact

    Server enable SNMP traps snmp authentication linkup, linkdown cold start

    Sysopt connection tcpmss 1200

    monitor SLA 123

    type echo protocol ipIcmpEcho 216.59.44.220 interface outside_pri

    Annex ALS life monitor 123 to always start-time now

    Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac

    Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac

    Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac

    Crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac

    Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac

    Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac

    Crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac

    Crypto ipsec transform-set ESP-AES-128-MD5-esp - aes esp-md5-hmac

    Crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac

    Crypto ipsec transform-set esp-3des-sha1 esp-3des esp-sha-hmac

    Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac

    life crypto ipsec security association seconds 28800

    Crypto ipsec kilobytes of life - safety 4608000 association

    Crypto ipsec df - bit clear-df outside_pri

    crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 pfs Group1 set

    Crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 value transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5

    card crypto outside_pri_map 1 match address outside_pri_1_cryptomap

    card crypto outside_pri_map 1 set pfs

    peer set card crypto outside_pri_map 1 50.75.217.246

    card crypto outside_pri_map 1 set of transformation-ESP-AES-256-MD5

    card crypto outside_pri_map 2 match address outside_pri_cryptomap

    peer set card crypto outside_pri_map 2 216.59.44.220

    card crypto outside_pri_map 2 the value transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5

    86400 seconds, duration of life card crypto outside_pri_map 2 set security-association

    card crypto outside_pri_map 3 match address outside_pri_cryptomap_1

    peer set card crypto outside_pri_map 3 216.59.44.220

    outside_pri_map crypto map 3 the value transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5

    outside_pri_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP

    card crypto outside_pri_map interface outside_pri

    crypto isakmp identity address

    ISAKMP crypto enable outside_pri

    crypto ISAKMP policy 5

    preshared authentication

    3des encryption

    sha hash

    Group 2

    life 86400

    crypto ISAKMP policy 10

    preshared authentication

    the Encryption

    sha hash

    Group 2

    life 86400

    crypto ISAKMP policy 30

    preshared authentication

    aes-256 encryption

    md5 hash

    Group 2

    life 86400

    crypto ISAKMP policy 50

    preshared authentication

    aes encryption

    md5 hash

    Group 2

    life 86400

    !

    track 1 rtr 123 accessibility

    Telnet timeout 5

    SSH 192.168.1.0 255.255.255.0 inside

    SSH timeout 5

    Console timeout 0

    management-access inside

    dhcpd auto_config outside_pri

    !

    dhcpd address 192.168.1.51 - 192.168.1.245 inside

    dhcpd dns 8.8.8.8 8.8.4.4 interface inside

    rental contract interface 86400 dhcpd inside

    dhcpd field LM inside interface

    dhcpd allow inside

    !

    a basic threat threat detection

    statistical threat detection port

    Statistical threat detection Protocol

    Statistics-list of access threat detection

    a statistical threat detection host number rate 2

    no statistical threat detection tcp-interception

    WebVPN

    port 980

    allow inside

    Select outside_pri

    enable SVC

    attributes of Group Policy DfltGrpPolicy

    VPN-idle-timeout no

    Protocol-tunnel-VPN IPSec l2tp ipsec svc webvpn

    internal GroupPolicy2 group strategy

    attributes of Group Policy GroupPolicy2

    Protocol-tunnel-VPN IPSec svc

    internal levelwingVPN group policy

    attributes of the strategy of group levelwingVPN

    Protocol-tunnel-VPN IPSec svc webvpn

    Split-tunnel-policy tunnelspecified

    value of Split-tunnel-network-list levelwingVPN_splitTunnelAcl

    username password encrypted Z74.JN3DGMNlP0H2 privilege 0 aard

    aard attribute username

    VPN-group-policy levelwingVPN

    type of remote access service

    rcossentino 4UpCXRA6T2ysRRdE encrypted password username

    username rcossentino attributes

    VPN-group-policy levelwingVPN

    type of remote access service

    bcherok evwBWqKKwrlABAUp encrypted password username

    username bcherok attributes

    VPN-group-policy levelwingVPN

    type of remote access service

    rscott nIOnWcZCACUWjgaP encrypted password privilege 0 username

    rscott username attributes

    VPN-group-policy levelwingVPN

    sryan 47u/nJvfm6kprQDs password encrypted username

    sryan username attributes

    VPN-group-policy levelwingVPN

    type of nas-prompt service

    username, password cbruch a8R5NwL5Cz/LFzRm encrypted privilege 0

    username cbruch attributes

    VPN-group-policy levelwingVPN

    type of remote access service

    apellegrino yy2aM21dV/11h7fR password encrypted username

    username apellegrino attributes

    VPN-group-policy levelwingVPN

    type of remote access service

    username rtuttle encrypted password privilege 0 79ROD7fRw5C4.l5

    username rtuttle attributes

    VPN-group-policy levelwingVPN

    username privilege 15 encrypted password vJFHerTwBy8dRiyW levelwingadmin

    username password nbrothers Amjc/rm5PYhoysB5 encrypted privilege 0

    username nbrothers attributes

    VPN-group-policy levelwingVPN

    clong z.yb0Oc09oP3/mXV encrypted password username

    clong attributes username

    VPN-group-policy levelwingVPN

    type of remote access service

    username, password finance 9TxE6jWN/Di4eZ8w encrypted privilege 0

    username attributes finance

    VPN-group-policy levelwingVPN

    Protocol-tunnel-VPN IPSec l2tp ipsec svc webvpn

    type of remote access service

    IPSec-attributes tunnel-group DefaultL2LGroup

    Disable ISAKMP keepalive

    tunnel-group 50.75.217.246 type ipsec-l2l

    IPSec-attributes tunnel-group 50.75.217.246

    pre-shared-key *.

    Disable ISAKMP keepalive

    type tunnel-group levelwingVPN remote access

    tunnel-group levelwingVPN General-attributes

    address LVCHSVPN pool

    Group Policy - by default-levelwingVPN

    levelwingVPN group of tunnel ipsec-attributes

    pre-shared-key *.

    tunnel-group 216.59.44.221 type ipsec-l2l

    IPSec-attributes tunnel-group 216.59.44.221

    pre-shared-key *.

    tunnel-group 216.59.44.220 type ipsec-l2l

    IPSec-attributes tunnel-group 216.59.44.220

    pre-shared-key *.

    Disable ISAKMP keepalive

    !

    !

    !

    Policy-map global_policy

    !

    context of prompt hostname

    Cryptochecksum:ed7f4451c98151b759d24a7d4387935b

    : end

    Hello

    It seems to me that you've covered most of the things.

    You however not "said" Configuring VPN L2L that traffic between the pool of VPN and network camp should be in tunnel

    outside_pri_cryptomap to access extended list ip 192.168.12.0 allow 255.255.255.0 object-group CHS-Colo

    Although naturally the remote end must also the corresponding configurations for users of VPN clients be able to pass traffic to the site of the camp.

    -Jouni

  • Please give index on configuring vpn site to site on 881 to ASA 5505 cisco router

    Earlier my boss asked me to prepare to implement the VPN site-to site on router Cisco 881 Integrated Services to ASA 5505 router, which is now running on the side of HQ. Someone please give me a hint. I am now learning the pdf file from Cisco that mention how to configure VPN site to site between 1812 Cisco IOS router and router of the ASA 5505 using ASDM V6.1 and SDM V2.5. Cannot find the book for the Cisco 881 device.

    Someone please please suggest me something as soon as POSSIBLE.

    Thank you

    CLI version:

    http://www.Cisco.com/en/us/products/HW/vpndevc/ps2030/products_configuration_example09186a00807ea936.shtml

    ASDM and SDM Version:

    http://www.Cisco.com/en/us/partner/products/ps5855/products_configuration_example09186a0080a9a7a3.shtml

  • Cisco RV110W

    Hi all

    I have the following question: I have 3 router CISCO rv110w. One of them is the most important for me is in my warehouse. The other two are in my shop. I want to do the first router (in-store) to the vpn server and the other two to be its vpn customers. Can you explain in detail how to proceed.

    Thanks in advance

    Dear Lubo,

    Thank you to the small community of Support Business.

    Please refer to the following document for a "VPN client" configuration on routers RV110W; "

    http://sbkb.Cisco.com/CiscoSB/Loginr.aspx?login=1&PID=2&app=search&VW=1&articleid=2501

    For a step by step over procedure detail consult the Administrator's guide, p.96;

    http://www.Cisco.com/en/us/docs/routers/CSBR/RV110W/Administration/Guide/rv110w_admin.PDF

    I hope you find this information useful and please let us know if there is any other assistance, we can help you.

    Kind regards

    Jeffrey Rodriguez S... : | :. : | :.
    Support Engineer Cisco client

    * Please rate the Post so other will know when an answer has been found.

  • Check the ISE for the VPN Cisco posture

    Hello community,

    first of all thank you for taking the time to read my post. I have a deployment in which requires the characteristic posture of controls for machines of VPN Cisco ISE. I know that logically once a machine on the LAN, Cisco ISE can detect and apply controls posture on clients with the Anyconnect agent but what about VPN machines? The VPN will end via a VPN concentrator, which then connects to an ASA5555X that is deployed as an IPS only. Are there clues to this?

    Thank you!

    The Cisco ASA Version 9.2.1 supports the change in RADIUS authorization (CoA) (RFC 5176). This allows for the gesticulations of users against the ISE Cisco VPN without the need of an IPN. Once a VPN user connects, the ASA redirects web traffic to the LSE, where the user is configured with a Network Admission Control (NAC) or Web Agent. The agent performs specific controls on the user's computer to determine its conformity against one together configured posture rules, such as the rules of operating system (OS) patches, AntiVirus, registry, Application, or Service.

    The posture validation results are then sent to the ISE. If the machine is considered the complaint, then the ISE can send a RADIUS CoA to the ASA with the new set of authorization policies. After validation of the successful posture and CoA, the user is allowed to access internal resources.

    http://www.Cisco.com/c/en/us/support/docs/security/Adaptive-Security-Appliance-ASA-software/117693-configure-ASA-00.html

  • Fall of connection Cisco RV110W

    Hi guys,.

    I was wondering if someone could help me,

    I bought a box of Cisco RV110W about a month ago and finally got around to setting up, but I have connection problems and have to reboot the box to make it work again, I am currently under the latest version of the firmware 1.2.0.10.

    I have a PPPOE connection on the WAN port with the correct credentials as the status page shows my IP address internet and WAN light is green, I have also 4 VLAN is configured.

    Trying to access the router outwardly I can't and I have to ask someone to restart while I can, but after a few minutes it will start to play. Y at - it somewhere I can access log files to see if the connection is down on the router.

    Thanks, Nick

    I am pleased to hear that it was a simple solution as the MTU. :)

    I believe you must have a syslog server to obtain complete connects (especially when you have a problem of blocking/restart as you did), although looking at the logs incoming and outgoing can be good for the basic diagnostic.  I hope that you can never look at the logs, now that everything works!

  • Client VPN Cisco router Cisco, MSW CA + certificates

    Dear Sirs,
    Let me approach you on the following problem.

    I wanted to use a secure between the Cisco VPN client connection
    (Windows XP) and Cisco 2821 with certificate-based authentication.
    I used the Microsoft certification authority (Windows 2003 server).
    Cisco VPN client used eTokenPRO Aladdin as a certificate store.

    Certificate of MSW CA registration and implementation in eToken ran OK
    Customer VPN Cisco doesn't have a problem with the cooperation of eToken.
    Certificate of registration of Cisco2821 MSW ca ran okay too.

    Cisco 2821 configuration is standard. IOS version 12.4 (6).

    Attempt to connect to the client VPN Cisco on Cisco 2821 was
    last update of the error messages:

    ISAKMP: (1020): cannot get router cert or routerdoes do not have a cert: had to find DN!
    ISAKMP: (1020): ITS been RSA signature authentication more XAUTH using id ID_FQDN type
    ISAKMP (1020): payload ID
    next payload: 6
    type: 2
    FULL domain name: cisco - ca.firm.com
    Protocol: 17
    Port: 500
    Length: 25
    ISAKMP: (1020): the total payload length: 25
    ISAKMP (1020): no cert string to send to peers
    ISAKMP (1020): peer not specified not issuing and none found appropriate profile
    ISAKMP (1020): Action of WSF returned the error: 2
    ISAKMP: (1020): entry = IKE_MESG_INTERNAL, IKE_PROCESS_COMPLETE
    ISAKMP: (1020): former State = new State IKE_R_MM5 = IKE_P1_COMPLETE

    Is there some refence where is possible to find some information on
    This problem? There is someone who knows how to understand these mistakes?
    Thank you very much for your help.

    Best regards
    P.Sonenberk

    PS Some useful information for people who are interested in the above problem.

    Address IP of Cisco 2821 10.1.1.220, client VPN IP address is 10.1.1.133.
    MSW's IP 10.1.1.50.
    Important parts of the Cisco 2821 configuration:

    !
    cisco-ca hostname
    !
    ................
    AAA new-model
    !
    AAA authentication login default local
    AAA authentication login sdm_vpn_xauth_ml_1 local
    AAA authorization exec default local
    AAA authorization sdm_vpn_group_ml_1 LAN
    !
    ...............
    IP domain name firm.com
    host IP company-cu 10.1.1.50
    host to IP cisco-vpn1 10.1.1.133
    name of the IP-server 10.1.1.33
    !
    Authenticated MultiLink bundle-name Panel
    !
    Crypto pki trustpoint TP-self-signed-4097309259
    enrollment selfsigned
    name of the object cn = IOS - Self - signed - certificate - 4097309259
    revocation checking no
    rsakeypair TP-self-signed-4097309259
    !
    Crypto pki trustpoint company-cu
    registration mode ra
    Enrollment url http://10.1.1.50:80/certsrv/mscep/mscep.dll
    use of ike
    Serial number no
    IP address no
    password 7 005C31272503535729701A1B5E40523647
    revocation checking no
    !
    TP-self-signed-4097309259 crypto pki certificate chain
    certificate self-signed 01
    30820249 308201B 2 A0030201 02020101 300 D 0609 2A 864886 F70D0101 04050030
    .............
    FEDDCCEA 8FD14836 24CDD736 34
    quit smoking
    company-cu pki encryption certificate chain
    certificate 1150A66F000100000013
    30820509 308203F1 A0030201 02020 HAS 11 092A 8648 01000000 13300 06 50A66F00
    ...............
    9E417C44 2062BFD5 F4FB9C0B AA
    quit smoking
    certificate ca 51BAC7C822D1F6A3469D1ADC32D0EB8C
    30820489 30820371 A0030201 BAC7C822 02021051 D1F6A346 9D1ADC32 D0EB8C30
    ...............
    C379F382 36E0A54E 0A6278A7 46
    quit smoking
    !
    ...................
    crypto ISAKMP policy 30
    BA 3des
    md5 hash
    authentication rsa-BA
    Group 2
    ISAKMP crypto identity hostname
    !
    Configuration group customer isakmp crypto Group159
    key Key159Key
    pool SDM_POOL_1
    ACL 100
    !
    the crypto isakmp client configuration group them
    domain firm.com
    pool SDM_POOL_1
    ACL 100
    !
    Crypto ipsec transform-set esp-3des esp-md5-hmac 3DES-MD5
    !
    crypto dynamic-map SDM_DYNMAP_1 1
    the transform-set 3DES-MD5 value
    market arriere-route
    !
    card crypto SDM_CMAP_1 client authentication list sdm_vpn_xauth_ml_1
    map SDM_CMAP_1 isakmp authorization list sdm_vpn_group_ml_1 crypto
    client configuration address map SDM_CMAP_1 crypto answer
    map SDM_CMAP_1 65535-isakmp dynamic SDM_DYNMAP_1 ipsec crypto
    !
    ................
    !
    end

    status company-cu of Cisco-ca #show cryptographic pki trustpoints
    Trustpoint company-cu:
    Issuing CA certificate configured:
    Name of the object:
    CN = firm-cu, dc = company, dc = local
    Fingerprint MD5: 5026582F 8CF455F8 56151047 2FFAC0D6
    Fingerprint SHA1: 47B 74974 7C85EA48 760516DE AAC84C5D 4427E829
    Universal router configured certificate:
    Name of the object:
    host name = cisco - ca.firm.com
    Fingerprint MD5: E78702ED 47D5D36F B732CC4C BA97A4ED
    Fingerprint SHA1: 78DEAE7E ACC12F15 1DFB4EB8 7FC DC6F3B7E 00138
    State:
    Generated keys... Yes (general purpose, not exportable)
    Authenticated issuing certification authority... Yes
    Request certificate (s)... Yes

    Cisco-ca #sh crypto pubkey-door-key rsa
    Code: M - configured manually, C - excerpt from certificate

    Name of code use IP-address/VRF Keyring
    C Signature name of X.500 DN default:
    CN = firm-cu
    DC = company
    DC = local

    C signature by default cisco-vpn1

    IMPORTANT: I don't have a Cisco IOS Software: 12.4 (5), 12.3 (11) T08, 12.4 (4.7) PI03c,.
    12.4 (4.7) T - there is error in the cryptographic module.

    Hey guys, it's weird that the router is not find cert after IKE is the cert and validates, it is certainly not reason, but I would go ahead and set up the mapping of certificate on this router to force the client to associate with Group of IKE, for that matter, that you need to change your config a bit for use iskamp profiles :

    http://www.Cisco.com/en/us/docs/iOS/12_3t/12_3t8/feature/guide/gt_isakp.html

  • 2 one-Site VPN Cisco 2801 and with crossing NAT

    Hi guys,.

    I would like to configure two Cisco 2801 using IPSEC/IKE. Both routers are connected to the internet through DSL lines. The DSL line have RFC1918 address side LAN where routers connected to the internet face. I can do NAT on DSL modems.

    Cisco IOS 2801 routers allow to configure site-2-site VPN with NAT crossing?

    Here is a model of physics/IP configuration:

    LAN<->2801 Modem DSL<-Internet->DSL modem<-Priv ip-=""> 2801<-Priv ip-=""><-> LAN

    Thank you

    Gonçalo

    Yes, you're good to go only if one or both of the sites has an IP address which is natted with private IP address statically. The implementation of IPSec on SRI NAT support in most crosses so that shouldn't be a concern

  • IPSec vpn cisco asa and acs 5.1

    We have configured authentication ipsec vpn cisco asa acs 5.1:

    Here is the config in cisco vpn 5580:

    standard access list acltest allow 10.10.30.0 255.255.255.0

    RADIUS protocol AAA-server Gserver

    AAA-server host 10.1.8.10 Gserver (inside)

    Cisco key

    AAA-server host 10.1.8.11 Gserver (inside)

    Cisco key

    internal group gpTest strategy

    gpTest group policy attributes

    Protocol-tunnel-VPN IPSec

    Split-tunnel-policy tunnelspecified

    value of Split-tunnel-network-list acltest

    type tunnel-group test remote access

    tunnel-group test general attributes

    address localpool pool

    Group Policy - by default-gpTest

    authentication-server-group LOCAL Gserver

    authorization-server-group Gserver

    accounting-server-group Gserver

    IPSec-attributes of tunnel-group test

    pre-shared-key cisco123

    GBA, we config user group: VPN users. all VPN users in this group. ACS can visit his political profile: If the user in the 'VPN users' group, access ACS.

    When we connect from a VPN Client to the server, all users connect to success. When you see the parser in ACS journal, each user success connect also get

    error:

    22040 wrong password or invalid shared secret

    (pls see picture to attach it)

    the system still works, but I don't know why, we get the error log.

    Thanks for any help you can provide!

    Duyen

    Hello Duyen,

    I think I've narrowed the issue. When remote access VPN using RADIUS authentication we must keep in mind that authentication and authorization are included on the same package.

    Depending on your configuration, the ACS is defined as a server RADIUS (Gserver Protocol radius aaa server) and becomes the VPN Tunnel authenticated and 'authorized' on this server group:

    authentication-server-group LOCAL Gserver

    authorization-server-group Gserver

    As noted above, the RADIUS of request/response includes authentication and authorization on the same package. This seems to be a problem of incorrect configuration that we should not set up the 'permission' in the Tunnel of the group.

    Please remove the authorization under the Tunnel of Group:

    No authorization-server-group Gserver

    Please test the connection again and check the logs of the ACS. At this point there are only sucessful newspaper reported on the side of the ACS.

    Is 'Permission-server-group' LDAP permission when authenticating to a LDAP server so to retrieve the attributes of permission on the server. RAY doesn't have the command as explained above.

    I hope this helps.

    Kind regards.

Maybe you are looking for

  • I can't get Firefox to open at all. Does anyone else have this problem?

    FF just opens when I click it. In the Task Manager, it appears in the background process only. I am running windows 8.1 on a laptop. I tried to restart the machine, I tried (many times) to uninstall and reinstall FF. When I look in the support sectio

  • Satellite A350 - Release Date?

    Anyone know the release date?

  • 4500 envy: envy printing crooked 4500

    I recently bought a desire connected 4500 wireless and everything's fine, other than that it prints about 1 degree perpendicular. I tried alignment head constantly, without change. None of the HP diagnostic tools detects a problem, but my eyes can't

  • RAM memory card compatibility

    HP Pavilion dv6-1230ec Windows 7 64 bit Hello I would like to know if I could install in my memory card new of NTB (as described above), exactly "" Patriot DDR2 SO-DIMM 4 GB PC2-5300 SL "- features here: site manufacturer . " Today, I have the origin

  • Win 7 driver for a Creative of DVB - T device.

    I'd appreciate the help. I have a Creative DVB - T Tuner & PVR, but there only XP drivers on the installation program. Can anyone tell if I can find the Vista/Win 7 drivers please?