Configuration with DSL ATT modem / E3000

Quick question, I have modem ADSL Netgear ATT 7550 with wireless capabilities and I have the linksys E3000 as well.

Since the E3000 is much faster, I was going to turn off the wireless on the 7550 and run it from the E3000.

The problem is when I try to configure the E3000 for PPPoE, I get an error that it cannot obtain an IP address. If I put it on DHCP, then it get an IP NAT of the 7550. The connection of the E3000 would become one very unstable cable.

In the past, all other routers had no problem obtaining address IP via PPPoE.

I know the 7550 is already connected via PPPoE, but it was the same setting that I have used with other wireless routers in the past.

Is there anything else that I do not?

Thank you

newone88,

Yes, there is something else that you do not. I have the same 7550.

You must connect to the 7550 to 192.168.1.254

Then go to the advanced settings. Search for "card PPP." Change the location of the PPP. This will put the 7550 in Full mode.

For best results, change the MTU on the default 'auto' to manual 1492 E3000.

Tags: Linksys Routers

Similar Questions

  • Configure BEFSR41 V.2.1. to use as switch with ADSL ZTE Modem in Bridged mode

    I found a thread of 2009 who has a link that could help me with this configuration, but the link does not work.

    I have a Linksys BEFSR41 V.2.1 and need to set it up, so I can use it as a switch with our ZTE 831 ADSL Modem, which is in bridged Mode.

    The IP address of the BEFSR41 changed to avoid a conflict with the address IP of Modem ZTE ADSL, which is 192.168.1.1 to 192.168.2.1.

    If the PC is connected directly to the ZTE ADSL Modem, I can access the Internet and I can access the Menu of Configuration of Modem ZTE.

    If the PC is directly connected to the Linksys BEFSR41, I can access the Menu of Configuration Linksys.

    If the PC is connected to the Linksys BEFSR41, and which is connected to the ZTE ADSL Modem, I can't access the Internet, and I cannot Ping the ZTE ADSL Modem.

    Please give me a URL that indicates how the Linksys BEFSR41 should be configured to use as a switch with my ADSL Modem from ZTE in bridged Mode.

    My belief is that after I have the Linksys set up, I then plug the ZTE ADSL modem in the Linksys unit and use it to DHCP.

    DRM for your time and help! Lanny

    1. I never told of any change on the Advanced Routing page.

    2 do not connect the internet port for ZTE with this kind of configuration. You cannot use the internet port.

    3. Once you set that you can use the remaining LAN for ethernet devices ports in your local network.

  • My verse ATT modem (non apple devices to use this modem} is connected to the ATT line, Time Capsule (iPhones, Macs Time Capsule use) via ethernet Uverse.) Non apple devices can collect data from iPhones or Mac using the time Capsule?

    My verse ATT modem ({use of devices not apple wifi of this modem} is connected to the ATT line, Time Capsule (iPhones, Macs use the wifi of the time Capsule) and connect to the Uverse modem via ethernet.)

    Both devices are set to the highest security and each uses separate passwords.

    Non apple devices can collect data from iPhones or Mac using the time Capsule?

    With a bit of work by someone who knows how to do such things, not Apple computers could read some files on the Mac if file sharing is configured on the network... devices non-Apple and... He knew the device passwords or administrator for Macs.

    Mac could also play the files on other Macs if file sharing has been implemented and the device password or admin was known.

    If you ask if a PC can read the files on the Time Capsule, the answer is Yes, without doubt, assuming that the PC knew the password of device for the time Capsule.

  • WRT54G with TWC new modem does not work anymore

    TWC has improved my modem.

    -before the upgrade, everything worked

    -I can connect to the internet with modem-> computer

    -J' cloned my MAC address in the router

    -J' have most of the things of value by default (gateway, DHCP, etc.).

    -J' have 2 desktop PC, Vonage, printer plugged into my router

    -J' I followed all the instructions on the configuration of the router with a cable modem

    -J' I power bike properly

    -J' saw numbers of IP address on my router status page

    -the instructions said I should consider to update my firmware.  I v2.2 latest firmware is 4.21.1 I already

    any ideas of what I could try or what tests to run?

    I found the solution to my problem here:

    http://forums.linksysbycisco.com/Linksys/board/message?board.ID=Wireless_Routers&message.ID=107567&query.ID=68050#M107567

    The reset button on the router was the key.

  • Not an Airprint printer can be configured with a new Macbook Air?

    Recently purchased a new Macbook Air.   Can it be configured with an older printer on our WiFi network that has no Airprint?

    Sure. At the end of the day, COMMAND + P (or CTRL + P in Windows) always sends this same basic command PRINT to the default printer. Any printer that is.

    The only problem is the printer driver software. If the manufacturer of the printer has written a driver that works with MacBook Air, download it, install it and make your old default printer.

  • I just got a new modem (Arris SB6190) and now my Airport Extreme does not connect.  It worked fine with the previous modem (a rented one TWC).  Help!

    I just got a new modem (Arris SB6190) and now my Airport Extreme does not connect.  It worked fine with the previous modem (a rented one TWC).  Help!

    Always recommended to reset the airport back to settings by default and then set up again whenever you have a new modem or change your Internet Service provider.

    Turn off the new modem for at least 30 minutes. More is better.

    Perform a hard reset on the AirPort Extreme, then it turned off.

    Make sure that the Ethernet cable connects the modem to the "O" on the AirPort Extreme WAN port

    After the power of the modem 30 minutes down, turn on the modem and let it run for at least 5 minutes by itself.

    Then, turn on the airport and let it run a few minutes

    Set up AirPort Extreme again

    Important note... There are many reports of problems with the modem Arris SB and airports. Both are great products, but they do seem to work perfectly together for some users.

  • PXI-8145 RT configured with LabVIEW RT 2009 running EVS, is this possible?

    Hello

    I'm interested to know if the "EVS" (engine shared Variables) can run on a PXI-8145RT configured with LabVIEW RT 2009? My needs would be only a few Boolean variables. Did someone tried this configuration?

    Thank you

    Michel

    Hello

    Thank you for the information. The upgrade was successful.

    Michel

  • XP - issue of modem - works with Westell 327W - now will not work with any other modem

    I use Westell 327W modem.  Verizon contacted on slow speed of ISP.  His person accessible tech my computer remotely and made various changes to the settings.  Did not help with the speed.  They then sent new modem - 7500 Westell.  However, I find now that while the computer always connects OK with the Westell 327W original, I can not connect with any other modem, including a new and several others that I have which was very well connected in the past.  I guess that the person tech made some changes to some settings that I place that affect the ability of the computer to recognize and to connect through a different modem.  The modem starts fine, all lights come on, but when I go to connect, I get a response that the remote modem does not recognize me.  Which parameter is one that handles it.  Thank you. Peggy

    Thanks - I have discovered that while I had an internet connection (that I could see), Verizon was not recognize me.  Problem is that I had to reinstall the software from Verizon for the new modem, which they had not told me I had to do (and did not).  Finally stumbled on it and had it solved, but thanks to the entry.

    By-the-way, he did not a thing to address the problem of low speed; their representative says it is 1.7 mps to the modem, the best that I get so 1.25, and it is habituellement.8 to 1.0.  Probably not your area of expertise

    Once again, thank you.

  • Problems with new cable modem and router

    Long story short, that my cable modem went bad.  I replaced it.  Now the two computers cannot connect to the internet.  It gives me a DNS error, saying that they can not find the server.  However, I can get on the internet if I hang the right modem to computer with courses through the router. I got it with the new modem a few days of work and use of the router, but now it does not work.

    There are 2 computers on the network, the two runnning vista.
    a linksys router model number BEFW11S4 ver 4.
    and the motorola surfboard SB5101 modem.  the old modem was a surfboard SB5100 motorcycle.

    There's a btn reset on the router (often the metal clip through a pin hole)
    Everything also its possible allways the router is bad

  • BEA-000362 < server failed. At least a migratable target is configured with automatic migration. Before the automatic migration of any type can be used, the MigrationBasis must be defined in the ClusterMBean. If the database is selected, then DataSourc

    My Weblogic 12 c StartWeblogic.cmd failed after that I configured the migration of the cluster to the database with the name of the table as none.  I can't even to the Server Admin page.

    Before that, I remove the. log.lck, process.id, process.lck files in the nodemanager directory

    Help, please! Thank you!

    Joe

    ****************************************************************************

    # < October 1, 2015 4:18:20 PM CDT > < Info > < security > < NAP1D692 > <>< Home > <><><>< 1443734300986 > < BEA-090905 > < disable provider JCE CryptoJ self-intégrité for better startup performance. To allow this control, enter - Dweblogic.security.allowCryptoJDefaultJCEVerification = true. >

    # < October 1, 2015 4:18:21 PM CDT > < Info > < security > < NAP1D692 > <>< Home > <><><>< 1443734301049 > < BEA-090906 > < change the default Random Number Generator in RSA CryptoJ of ECDRBG128 to FIPS186PRNG. To disable this change, specify - Dweblogic.security.allowCryptoJDefaultPRNG = true. >

    # < October 1, 2015 4:18:21 PM CDT > < opinion > < WebLogicServer > < NAP1D692 > <>< Home > <><><>< 1443734301064 > < BEA-000395 > < the following extensions added at the end of the classpath directory content:

    C:\oracle\Middleware\Oracle_Home\user_projects\domains\joe12c_domain\lib\log4j-1.2.15.jar; C:\oracle\Middleware\Oracle_Home\user_projects\domains\joe12c_domain\lib\wllog4j.jar. >

    # < October 1, 2015 4:18:21 PM CDT > < Info > < WebLogicServer > < NAP1D692 > <>< Thread-4 > <><><>< 1443734301361 > < BEA-000377 > < since Java hotspot 64-bit Server VM WebLogic Server Version 24.60 - b09 of Oracle Corporation. >

    # < October 1, 2015 4:18:21 PM CDT > < Info > < management > < NAP1D692 > <>< Thread-5 > <><><>< 1443734301610 > < BEA-141107 > < Version: WebLogic Server 12.1.3.0.0 Wed May 21 18:53:34 PDT 2014 1604337 >

    # < October 1, 2015 4:18:22 PM CDT > < opinion > < WebLogicServer > < NAP1D692 > <>< Thread-6 > <><><>< 1443734302702 > < BEA-000365 > < Server State has changed at the START. >

    # < October 1, 2015 4:18:22 PM CDT > < Info > < WorkManager > < NAP1D692 > <>< Thread-6 > <><><>< 1443734302702 > < BEA-002900 > < init > self-adjustable thread pool.

    # < October 1, 2015 4:18:22 PM CDT > < Info > < WorkManager > < NAP1D692 > <>< ExecuteThread [ASSET]: '0' for the queue: "(self-adjusting) weblogic.kernel.Default" > <><><>< 1443734302733 > < BEA-002942 > < CMM level memory becomes 0. Sleep thread pool to 256. >

    # < October 1, 2015 4:18:22 PM CDT > < Info > < WebLogicServer > < NAP1D692 > <>< Thread-6 > <><><>< 1443734302733 > < BEA-000214 > < WebLogic Server "AdminServer" version:

    WebLogic Server 12.1.3.0.0 Wed May 21 18:53:34 PDT 2014 1604337 Copyright (c) 1995,2014, Oracle and/or its affiliates. All rights reserved. >

    # < October 1, 2015 4:18:23 PM CDT > < Info > < Server > < NAP1D692 > <>< Thread-6 > <><><>< 1443734303264 > < BEA-002622 > < Protocol 't3' is now configured. >

    # < October 1, 2015 4:18:23 PM CDT > < Info > < Server > < NAP1D692 > <>< Thread-6 > <><><>< 1443734303264 > < BEA-002622 > < Protocol "t3s" is now configured. >

    # < October 1, 2015 4:18:23 PM CDT > < Info > < Server > < NAP1D692 > <>< Thread-6 > <><><>< 1443734303264 > < BEA-002622 > < the 'http' Protocol is now configured. >

    # < October 1, 2015 4:18:23 PM CDT > < Info > < Server > < NAP1D692 > <>< Thread-6 > <><><>< 1443734303264 > < BEA-002622 > < the "https" Protocol is now configured. >

    # < October 1, 2015 4:18:23 PM CDT > < Info > < Server > < NAP1D692 > <>< Thread-6 > <><><>< 1443734303264 > < BEA-002622 > < Protocol "iiop" is now configured. >

    # < October 1, 2015 4:18:23 PM CDT > < Info > < Server > < NAP1D692 > <>< Thread-6 > <><><>< 1443734303264 > < BEA-002622 > < Protocol 'iiops' is now configured. >

    # < October 1, 2015 4:18:23 PM CDT > < Info > < Server > < NAP1D692 > <>< Thread-6 > <><><>< 1443734303264 > < BEA-002622 > < "ldap" Protocol is now configured. >

    # < October 1, 2015 4:18:23 PM CDT > < Info > < Server > < NAP1D692 > <>< Thread-6 > <><><>< 1443734303264 > < BEA-002622 > < Protocol "ldaps" is now set up. >

    # < October 1, 2015 4:18:23 PM CDT > < Info > < Server > < NAP1D692 > <>< Thread-6 > <><><>< 1443734303264 > < BEA-002622 > < Protocol "cluster" is now configured. >

    # < October 1, 2015 4:18:23 PM CDT > < Info > < Server > < NAP1D692 > <>< Thread-6 > <><><>< 1443734303264 > < BEA-002622 > < Protocol 'clusters' is now configured. >

    # < October 1, 2015 4:18:23 PM CDT > < Info > < Server > < NAP1D692 > <>< Thread-6 > <><><>< 1443734303264 > < BEA-002622 > < the "SNMP" is now configured. >

    # < October 1, 2015 4:18:23 PM CDT > < Info > < Server > < NAP1D692 > <>< Thread-6 > <><><>< 1443734303264 > < BEA-002622 > < Protocol "admin" is now configured. >

    # < October 1, 2015 4:18:23 PM CDT > < Info > < Server > < NAP1D692 > <>< Thread-6 > <><><>< 1443734303264 > < BEA-002624 > < administration Protocol is "t3s" and is now configured. >

    # < October 1, 2015 4:18:23 PM CDT > < Info > < RJVM > < NAP1D692 > <>< Thread-5 > <><><>< 1443734303264 > < BEA-000570 > < Network Configuration for channel "AdminServer.

    Listening address: 7001

    Address public n/a

    True active http

    Tunneling Enabled false

    Outgoing Enabled false

    Admin traffic enabled true fake license to ResolveDNSName >

    # < October 1, 2015 4:18:23 PM CDT > < Debug > < RJVM > < NAP1D692 > <>< Thread-5 > <><><>< 1443734303264 > < BEA-000571 > < retail network for channel "AdminServer.

    Weight of the channel 50

    Accept the rear 300

    Timeout 5000ms

    Message Max Size 10000000

    Timeout message 60 years

    Timeout of 65

    Tunneling Timeout 40 s

    Tunneling Ping 45 s >

    # < October 1, 2015 4:18:23 PM CDT > < Info > < Server > < NAP1D692 > <>< Thread-5 > <><><>< 1443734303279 > < BEA-002609 > < channel Service initialized. >

    # < October 1, 2015 4:18:23 PM CDT > < opinion > < Log Management > < NAP1D692 > <>< ExecuteThread [pending]: '1' for the queue: "(self-adjusting) weblogic.kernel.Default" > <><><>< 1443734303357 > < BEA-170019 > < C:\oracle\Middleware\Oracle_Home\user_projects\domains\joe12c_domain\servers\AdminServer\logs\AdminServer.log server log file is opened. All events in the log server-side will be written to this file. >

    # < October 1, 2015 4:18:23 PM CDT > < Info > < Log Management > < NAP1D692 > <>< ExecuteThread [pending]: '1' for the queue: "(self-adjusting) weblogic.kernel.Default" > <><><>< 1443734303404 > < BEA-170023 > < logging of the server is initialized with the Java application logging API. >

    # < October 1, 2015 4:18:23 PM CDT > < Info > < IIOP > < NAP1D692 > <>< [STANDBY] ExecuteThread: '2' for the queue: "(self-adjusting) weblogic.kernel.Default" > <><><>< 1443734303404 > < BEA-002014 > < subsystem enabled IIOP. >

    # < October 1, 2015 4:18:23 PM CDT > < Info > < Log Management > < NAP1D692 > < AdminServer > < [pending] ExecuteThread: '1' for the queue: '(self-adjusting) weblogic.kernel.Default' > < < WLS Kernel > > <><>< 1443734303404 > < BEA-170025 > < initialized Logging area. Events in the field log will be written to C:\oracle\Middleware\Oracle_Home\user_projects\domains\joe12c_domain\servers\AdminServer\logs/joe12c_domain.log. >

    # < October 1, 2015 4:18:23 PM CDT > < Info > < Diagnostics > < NAP1D692 > < AdminServer > < [pending] ExecuteThread: '1' for the queue: '(self-adjusting) weblogic.kernel.Default' > < < WLS Kernel > > <><>< 1443734303451 > < BEA-320001 > < ServerDebug The service initialized successfully. >

    # < October 1, 2015 4:18:23 PM CDT > < Info > < Store > < NAP1D692 > < AdminServer > < [pending] ExecuteThread: '1' for the queue: '(self-adjusting) weblogic.kernel.Default' > < < WLS Kernel > > <><>< 1443734303513 > < BEA-280008 > < open the persistent store of file 'WLS_DIAGNOSTICS' for recovery: directory = C:\oracle\Middleware\Oracle_Home\user_projects\domains\joe12c_domain\servers\AdminServer\data\store\diagnostics requestedWritePolicy = "Disabled" fileLockingEnabled = true driver = "wlfileio3." >

    # < October 1, 2015 4:18:23 PM CDT > < Info > < Store > < NAP1D692 > < AdminServer > < [pending] ExecuteThread: '1' for the queue: '(self-adjusting) weblogic.kernel.Default' > < < WLS Kernel > > <><>< 1443734303529 > < BEA-280103 > < storage of persistent files "WLS_DIAGNOSTICS" puts in cache in weblogic.store.io.file.direct.FileMapping [granularity = 65536 io mapped =]. >

    # < October 1, 2015 4:18:23 PM CDT > < Info > < management > < NAP1D692 > < AdminServer > < [pending] ExecuteThread: '2' for the queue: '(self-adjusting) weblogic.kernel.Default' > < < WLS Kernel > > <><>< 1443734303529 > < BEA-141278 > < Java configuration entropy is: property system "java.security.egd = null; File JRE java.security "securerandom.source = file:/dev/urandom" property Blocking of the Config = false; Version of the JDK = 1.7.0_60; Operating system = Windows 7. >

    # < October 1, 2015 4:18:23 PM CDT > < Info > < management > < NAP1D692 > < AdminServer > < [pending] ExecuteThread: '2' for the queue: '(self-adjusting) weblogic.kernel.Default' > < < WLS Kernel > > <><>< 1443734303545 > < BEA-141280 > < configuration detected NON-BLOCKING of entropy of java. This setting you will give the best performance on machines with limited sources of entropy, but is less secure than a blocking entropy configuration. >

    # < October 1, 2015 4:18:23 PM CDT > < Info > < management > < NAP1D692 > < AdminServer > < [pending] ExecuteThread: '2' for the queue: '(self-adjusting) weblogic.kernel.Default' > < < WLS Kernel > > <><>< 1443734303545 > < BEA-141187 > < Java System properties are defined as follows:

    awt. Toolkit = sun.awt.windows.WToolkit

    leader. Encoding = Cp1252

    leader. Encoding.pkg = sun.io

    leader. Separator =.

    Java.awt.graphicsenv = sun.awt.Win32GraphicsEnvironment

    Java.awt.PrinterJob = sun.awt.windows.WPrinterJob

    Java.class.Path = C:\JDK17~1.0_6\lib\tools.jar; C:\oracle\MIDDLE~1\ORACLE~1\wlserver\server\lib\weblogic_sp.jar; C:\oracle\MIDDLE~1\ORACLE~1\wlserver\server\lib\weblogic.jar; C:\oracle\MIDDLE~1\ORACLE~1\oracle_common\modules\net. SF.antcontrib_1.1.0.0_1-0b3\lib\ant-contrib.jar; C:\oracle\MIDDLE~1\ORACLE~1\wlserver\modules\features\oracle.WLS.common.nodemanager_2.0.0.0.jar; C:\oracle\MIDDLE~1\ORACLE~1\oracle_common\modules\com. Oracle.Cie.config - WLS - online_8.1.0.0.jar; C:\oracle\MIDDLE~1\ORACLE~1\wlserver\common\derby\lib\derbyclient.jar; C:\oracle\MIDDLE~1\ORACLE~1\wlserver\common\derby\lib\derby.jar; C:\oracle\MIDDLE~1\ORACLE~1\wlserver\server\lib\xqrl.jar; C:\oracle\MIDDLE~1\ORACLE~1\wlserver\server\lib\weblogic.jar; C:\Progra~2\IBM\RATION~1\CLEARQ~1\cqjni.jar

    Java.class.version = 51.0

    Java.endorsed.dirs = C:\JDK17~1.0_6\jre\lib\endorsed; C:\oracle\MIDDLE~1\ORACLE~1\oracle_common\modules\endorsed

    Java.ext.dirs = C:\JDK17~1.0_6\jre\lib\ext; C:\Windows\Sun\Java\lib\ext

    Java.Home = C:\JDK17~1.0_6\jre

    Java.IO.TMPDIR =

    Java.Library.Path = C:\JDK17~1.0_6\bin; C:\Windows\Sun\Java\bin; C:\Windows\System32; C:\Windows; C:\oracle\MIDDLE~1\ORACLE~1\wlserver\server\native\win\x64; C:\oracle\MIDDLE~1\ORACLE~1\wlserver\server\bin; C:\oracle\MIDDLE~1\ORACLE~1\oracle_common\modules\org. Apache.ant_1.9.2\bin; C:\JDK17~1.0_6\jre\bin; C:\JDK17~1.0_6\bin; C:\Progra~2\IBM\RATION~1\common; C:\Progra~3\Oracle\Java\javapath; C:\oracle\product\102~1.0\client_1\BIN; C:\Progra~2\BUSINE~1\Common\3.5\bin\NOTES\; C:\Windows\System32; C:\Windows; C:\Windows\System32\wbem; C:\Windows\System32\WINDOW~1\v1.0\; C:\Progra~2\HEAT\;\\nap-lvip-047\scmref\bin; C:\JDK17~1.0_5;\\nap-lvip-047\maven\M3R1SW~N.9\bin; C:\Progra~2\CODECO~1;\\nap-lvip-047\scmref\bin; C:\Windows\System32; C:\Progra~2\IBM\gsk8\lib; C:\Progra~2\IBM\gsk8\bin; C:\Progra~2\IBM\RATION~1\CLEARC~1\Bin; C:\Progra~2\IBM\RATION~1\CLEARC~1\REMOTE~1\cteapis; C:\oracle\MIDDLE~1\ORACLE~1\wlserver\server\native\win\x64\oci920_8;.

    Java.naming.Factory.initial = weblogic.jndi.WLInitialContextFactory

    Java.naming.Factory.URL.pkgs = weblogic.jndi.factories:weblogic.corba.j2ee.naming.url:weblogic.jndi.factories:weblogic.corba.j2ee.naming.url

    Java.Runtime.Name = Java (TM) SE Runtime Environment

    Java.Runtime.version = 1.7.0_60 - b19

    Java.Security.Policy = C:\oracle\MIDDLE~1\ORACLE~1\wlserver\server\lib\weblogic.policy

    Java.Specification.Name = Java Platform API Specification

    Java.Specification.Vendor = Oracle Corporation

    Java.Specification.version = 1.7

    Java.Vendor = Oracle Corporation

    Java.vendor.URL = http://Java.Oracle.com/

    Java.vendor.URL.bug = http://bugreport.Sun.com/bugreport/

    Java.version = 1.7.0_60

    Java.VM.info = mixed mode

    Java.VM.Name = VM Server Java hotspot 64-Bit

    Java.VM.Specification.Name = specification of Machine Java virtual

    Java.VM.Specification.Vendor = Oracle Corporation

    Java.VM.Specification.version = 1.7

    Java.VM.Vendor = Oracle Corporation

    Java.VM.version = 24, 60 - b09

    javax. Management.Builder.initial = weblogic.management.jmx.mbeanserver.WLSMBeanServerBuilder

    javax.rmi.CORBA.PortableRemoteObjectClass = weblogic.iiop.PortableRemoteObjectDelegateImpl

    javax.rmi.CORBA.UtilClass = weblogic.iiop.UtilDelegateImpl

    org.omg.CORBA.ORBClass = weblogic.corba.orb.ORB

    org.omg.CORBA.ORBSingletonClass = weblogic.corba.orb.ORB

    OS. Arch = amd64

    OS. Name = Windows 7

    OS.version = 6.1

    Path.Separator =;

    Sun.Arch.Data.Model = 64

    Sun.Boot.class.Path = C:\oracle\MIDDLE~1\ORACLE~1\oracle_common\modules\endorsed\javax-xml-bind.jar; C:\oracle\MIDDLE~1\ORACLE~1\oracle_common\modules\endorsed\javax-XML-WS.jar; C:\oracle\MIDDLE~1\ORACLE~1\oracle_common\modules\endorsed\jsr250-API.jar; C:\JDK17~1.0_6\jre\lib\resources.jar; C:\JDK17~1.0_6\jre\lib\rt.jar; C:\JDK17~1.0_6\jre\lib\sunrsasign.jar; C:\JDK17~1.0_6\jre\lib\jsse.jar; C:\JDK17~1.0_6\jre\lib\jce.jar; C:\JDK17~1.0_6\jre\lib\charsets.jar; C:\JDK17~1.0_6\jre\lib\jfr.jar; C:\JDK17~1.0_6\jre\classes

    Sun.Boot.Library.Path = C:\JDK17~1.0_6\jre\bin

    Sun.CPU.endian = little

    Sun.CPU.isalist = amd64

    Sun.Desktop = windows

    Sun.IO.Unicode.Encoding = UnicodeLittle

    Sun.java.Command = weblogic. Server

    Sun.java.Launcher = SUN_STANDARD

    Sun.JNU.Encoding = Cp1252

    Sun.Management.Compiler = HotSpot 64 bits compilers Tiered

    Sun.OS.patch.Level = Service Pack 1

    User.country = en

    User.dir = C:\oracle\Middleware\Oracle_Home\user_projects\domains\joe12c_domain

    User.Home =

    User.language = en

    User.Name =

    User.TimeZone =

    VDE. Home = C:\oracle\Middleware\Oracle_Home\user_projects\domains\joe12c_domain\servers\AdminServer\data\ldap

    WebLogic. Name = AdminServer

    WebLogic.Home = C:\oracle\MIDDLE~1\ORACLE~1\wlserver\server

    WLS. Home = C:\oracle\MIDDLE~1\ORACLE~1\wlserver\server

    . >

    # < October 1, 2015 4:18:23 PM CDT > < Info > < Store > < NAP1D692 > < AdminServer > < [pending] ExecuteThread: '1' for the queue: '(self-adjusting) weblogic.kernel.Default' > < < WLS Kernel > > <><>< 1443734303545 > < BEA-280009 > < storing files persistent "WLS_DIAGNOSTICS" (75765a60-c009-403f-a7ed-c6a75a86e1c8) has been opened: blockSize = 512 actualWritePolicy = "Disabled(single-handle-non-direct)" explicitIOEnforced = false files = 25. " >

    # < October 1, 2015 4:18:23 PM CDT > < Info > < XML > < NAP1D692 > < AdminServer > < ExecuteThread [ASSET]: '0' for the queue: '(self-adjusting) weblogic.kernel.Default' > < < WLS Kernel > > <><>< 1443734303592 > < BEA-130036 > < XMLRegistry initialization >

    # < October 1, 2015 4:18:23 PM CDT > < Info > < Socket > < NAP1D692 > < AdminServer > < [pending] ExecuteThread: '2' for the queue: '(self-adjusting) weblogic.kernel.Default' > < < WLS Kernel > > <><>< 1443734303662 > < BEA-000436 > < allocate 4 player son. >

    # < October 1, 2015 4:18:23 PM CDT > < Info > < Socket > < NAP1D692 > < AdminServer > < [pending] ExecuteThread: '2' for the queue: '(self-adjusting) weblogic.kernel.Default' > < < WLS Kernel > > <><>< 1443734303662 > < BEA-000446 > < active native to IO. >

    # < October 1, 2015 4:18:23 PM CDT > < Info > < security > < NAP1D692 > < AdminServer > < ExecuteThread [pending]: '3' for queue: '(self-adjusting) weblogic.kernel.Default' > < < WLS Kernel > > <><>< 1443734303849 > < BEA-000000 > < OpenJPA starting 1.1.1 - SNAPSHOT >

    # < October 1, 2015 4:18:24 PM CDT > < Info > < security > < NAP1D692 > < AdminServer > < ExecuteThread [pending]: '3' for queue: '(self-adjusting) weblogic.kernel.Default' > < < WLS Kernel > > <><>< 1443734304005 > < BEA-000000 > < StoreServiceImpl.initJDO - StoreService is initialized with Id = ldap_PyMqKeZifftJZ2SHXoWLnh4Ldn4 = >

    # < October 1, 2015 4:18:24 PM CDT > < Info > < security > < NAP1D692 > < AdminServer > < ExecuteThread [pending]: '3' for queue: '(self-adjusting) weblogic.kernel.Default' > < < WLS Kernel > > <><>< 1443734304021 > < BEA-090516 > < authenticator provider has already given LDAP. >

    # < October 1, 2015 4:18:24 PM CDT > < Info > < security > < NAP1D692 > < AdminServer > < ExecuteThread [pending]: '3' for queue: '(self-adjusting) weblogic.kernel.Default' > < < WLS Kernel > > <><>< 1443734304114 > < BEA-090516 > < provider authorized person a pre-existing LDAP data. >

    # < October 1, 2015 4:18:24 PM CDT > < Info > < security > < NAP1D692 > < AdminServer > < ExecuteThread [pending]: '3' for queue: '(self-adjusting) weblogic.kernel.Default' > < < WLS Kernel > > <><>< 1443734304301 > < BEA-090516 > < CredentialMapper a pre-existing LDAP provider data. >

    # < October 1, 2015 4:18:24 PM CDT > < Info > < security > < NAP1D692 > < AdminServer > < ExecuteThread [pending]: '3' for queue: '(self-adjusting) weblogic.kernel.Default' > < < WLS Kernel > > <><>< 1443734304317 > < BEA-090516 > < RoleMapper a pre-existing LDAP provider data. >

    # < October 1, 2015 4:18:24 PM CDT > < Info > < security > < NAP1D692 > < AdminServer > < ExecuteThread [pending]: '3' for queue: '(self-adjusting) weblogic.kernel.Default' > < < WLS Kernel > > <><>< 1443734304379 > < BEA-090093 > < no pre - WLS 8.1 Keystore provider is configured for server security realm myrealm AdminServer. >

    # < October 1, 2015 4:18:24 PM CDT > < opinion > < security > < NAP1D692 > < AdminServer > < ExecuteThread [pending]: '3' for queue: '(self-adjusting) weblogic.kernel.Default' > < < WLS Kernel > > <><>< 1443734304379 > < BEA-090082 > < security initialization using security realm myrealm. >

    # < October 1, 2015 4:18:24 PM CDT > < Info > < connector > < NAP1D692 > < AdminServer > < [pending] ExecuteThread: '1' for the queue: '(self-adjusting) weblogic.kernel.Default' > < < WLS Kernel > > <><>< 1443734304457 > < BEA-190000 > < J2EE Connector Service initialization. >

    # < October 1, 2015 4:18:24 PM CDT > < Info > < connector > < NAP1D692 > < AdminServer > < [pending] ExecuteThread: '1' for the queue: '(self-adjusting) weblogic.kernel.Default' > < < WLS Kernel > > <><>< 1443734304457 > < BEA-190001 > < Service connector J2EE initialized successfully. >

    # < October 1, 2015 4:18:24 PM CDT > < Info > < Store > < NAP1D692 > < AdminServer > < ExecuteThread [ASSET]: '0' for the queue: '(self-adjusting) weblogic.kernel.Default' > < < WLS Kernel > > <><>< 1443734304473 > < BEA-280008 > < opening persistent store file '_WLS_AdminServer' for recovery: directory = C:\oracle\Middleware\Oracle_Home\user_projects\domains\joe12c_domain\servers\AdminServer\data\store\default requestedWritePolicy = fileLockingEnabled 'Direct entry' = true driver = "wlfileio3." >

    # < October 1, 2015 4:18:24 PM CDT > < Info > < JMX > < NAP1D692 > < AdminServer > < [pending] ExecuteThread: '2' for the queue: '(self-adjusting) weblogic.kernel.Default' > < < WLS Kernel > > <><>< 1443734304504 > < BEA-149512 > < JMX connector server started service: jmx:iiop://10.29.11.182:7001/jndi/weblogic.management.mbeanservers.runtime. >

    # < October 1, 2015 4:18:24 PM CDT > < Info > < JMS > < NAP1D692 > < AdminServer > < ExecuteThread [pending]: '3' for queue: '(self-adjusting) weblogic.kernel.Default' > < < WLS Kernel > > <><>< 1443734304535 > < BEA-040305 > < JMS service is initialized and standby mode. >

    # < October 1, 2015 4:18:24 PM CDT > < Info > < JMS > < NAP1D692 > < AdminServer > < ExecuteThread [pending]: '3' for queue: '(self-adjusting) weblogic.kernel.Default' > < < WLS Kernel > > <><>< 1443734304567 > < BEA-040090 > < 8 deployed by default connection factories. >

    # < October 1, 2015 4:18:24 PM CDT > < Info > < JMS > < NAP1D692 > < AdminServer > < ExecuteThread [pending]: '3' for queue: '(self-adjusting) weblogic.kernel.Default' > < < WLS Kernel > > <><>< 1443734304567 > < BEA-040407 > < connection factory default 'DefaultXAConnectionFactory2' with 'weblogic.jms.XAConnectionFactory2' JNDI name is started >.

    # < October 1, 2015 4:18:24 PM CDT > < Info > < JMS > < NAP1D692 > < AdminServer > < ExecuteThread [pending]: '3' for queue: '(self-adjusting) weblogic.kernel.Default' > < < WLS Kernel > > <><>< 1443734304567 > < BEA-040407 > < connection factory default 'MessageDrivenBeanConnectionFactory' with 'weblogic.jms.MessageDrivenBeanConnectionFactory' JNDI name is started >.

    # < October 1, 2015 4:18:24 PM CDT > < Info > < JMS > < NAP1D692 > < AdminServer > < ExecuteThread [pending]: '3' for queue: '(self-adjusting) weblogic.kernel.Default' > < < WLS Kernel > > <><>< 1443734304567 > < BEA-040407 > < connection factory default 'DefaultConnectionFactory' with 'weblogic.jms.ConnectionFactory' JNDI name is started >.

    # < October 1, 2015 4:18:24 PM CDT > < Info > < JMS > < NAP1D692 > < AdminServer > < ExecuteThread [pending]: '3' for queue: '(self-adjusting) weblogic.kernel.Default' > < < WLS Kernel > > <><>< 1443734304567 > < BEA-040407 > < connection factory default 'TopicConnectionFactory' with his "javax.jms.TopicConnectionFactory" JNDI name is started >.

    # < October 1, 2015 4:18:24 PM CDT > < Info > < JMS > < NAP1D692 > < AdminServer > < ExecuteThread [pending]: '3' for queue: '(self-adjusting) weblogic.kernel.Default' > < < WLS Kernel > > <><>< 1443734304567 > < BEA-040407 > < connection factory default 'DefaultXAConnectionFactory' with 'weblogic.jms.XAConnectionFactory' JNDI name is started >.

    # < October 1, 2015 4:18:24 PM CDT > < Info > < JMS > < NAP1D692 > < AdminServer > < ExecuteThread [pending]: '3' for queue: '(self-adjusting) weblogic.kernel.Default' > < < WLS Kernel > > <><>< 1443734304567 > < BEA-040407 > < connection factory default 'DefaultXAConnectionFactory0' with 'weblogic.jms.XAConnectionFactory0' JNDI name is started >.

    # < October 1, 2015 4:18:24 PM CDT > < Info > < JMS > < NAP1D692 > < AdminServer > < ExecuteThread [pending]: '3' for queue: '(self-adjusting) weblogic.kernel.Default' > < < WLS Kernel > > <><>< 1443734304567 > < BEA-040407 > < default connection factory is started 'Factory' with his "javax.jms.QueueConnectionFactory" JNDI name >.

    # < October 1, 2015 4:18:24 PM CDT > < Info > < JMS > < NAP1D692 > < AdminServer > < ExecuteThread [pending]: '3' for queue: '(self-adjusting) weblogic.kernel.Default' > < < WLS Kernel > > <><>< 1443734304567 > < BEA-040407 > < connection factory default 'DefaultXAConnectionFactory1' with 'weblogic.jms.XAConnectionFactory1' JNDI name is started >.

    # < October 1, 2015 4:18:24 PM CDT > < Info > < JMS > < NAP1D692 > < AdminServer > < ExecuteThread [pending]: '3' for queue: '(self-adjusting) weblogic.kernel.Default' > < < WLS Kernel > > <><>< 1443734304567 > < BEA-040306 > < JMS service is now active. >

    # < October 1, 2015 4:18:24 PM CDT > < Info > < JMX > < NAP1D692 > < AdminServer > < ExecuteThread [pending]: '3' for queue: '(self-adjusting) weblogic.kernel.Default' > < < WLS Kernel > > <><>< 1443734304629 > < BEA-149512 > < JMX connector server started service: jmx:iiop://10.29.11.182:7001/jndi/weblogic.management.mbeanservers.domainruntime. >

    # < October 1, 2015 4:18:24 PM CDT > < Info > < Store > < NAP1D692 > < AdminServer > < ExecuteThread [ASSETS]: '0' for the queue: '(self-adjusting) weblogic.kernel.Default' > < < WLS Kernel > > <><>< 1443734304676 > < BEA-280009 > < file persistent store "_WLS_AdminServer" (c54c7ab9-2eab-4095-ba3c-5abb38f06231) has been opened: blockSize = 512 actualWritePolicy = "Direct-Write(read-buffered)" explicitIOEnforced = false documents = 21. " >

    # < October 1, 2015 4:18:24 PM CDT > < Info > < JMX > < NAP1D692 > < AdminServer > < ExecuteThread [pending]: '3' for queue: '(self-adjusting) weblogic.kernel.Default' > < < WLS Kernel > > <><>< 1443734304691 > < BEA-149512 > < JMX connector server started service: jmx:iiop://10.29.11.182:7001/jndi/weblogic.management.mbeanservers.edit. >

    # < October 1, 2015 4:18:24 PM CDT > < Info > < JDBC > < NAP1D692 > < AdminServer > < ExecuteThread [ASSET]: '0' for the queue: '(self-adjusting) weblogic.kernel.Default' > < < WLS Kernel > > <><>< 1443734304769 > < BEA-001135 > < init > the JDBC service.

    # < October 1, 2015 4:18:24 PM CDT > < Info > < JDBC > < NAP1D692 > < AdminServer > < ExecuteThread [ASSET]: '0' for the queue: '(self-adjusting) weblogic.kernel.Default' > < < WLS Kernel > > <><>< 1443734304785 > < BEA-001137 > < full initialization >.

    # < October 1, 2015 4:18:24 PM CDT > < Info > < JDBC > < NAP1D692 > < AdminServer > < ExecuteThread [ASSET]: '0' for the queue: '(self-adjusting) weblogic.kernel.Default' > < < WLS Kernel > > <><>< 1443734304785 > < BEA-001138 > < Recovery > JDBC service.

    # < October 1, 2015 4:18:24 PM CDT > < Info > < JDBC > < NAP1D692 > < AdminServer > < ExecuteThread [ASSET]: '0' for the queue: '(self-adjusting) weblogic.kernel.Default' > < < WLS Kernel > > <><>< 1443734304785 > < BEA-001140 > < complete resume >.

    # < October 1, 2015 4:18:24 PM CDT > < Info > < messaging.interception > < NAP1D692 > < AdminServer > < ExecuteThread [ASSET]: '0' for the queue: '(self-adjusting) weblogic.kernel.Default' > < < WLS Kernel > > <><>< 1443734304816 > < BEA-400000 > < initialization message interception service. >

    # < October 1, 2015 4:18:24 PM CDT > < Info > < Server > < NAP1D692 > < AdminServer > < ExecuteThread [pending]: '3' for queue: '(self-adjusting) weblogic.kernel.Default' > < < WLS Kernel > > <><>< 1443734304863 > < BEA-002622 > < Protocol "[https, t3, snmp, cluster-broadcast-secure, ldaps, cluster-broadcast, ldap, http, iiop, admin, t3s '. "[, iiops]" is now set up. >

    # < October 1, 2015 4:18:24 PM CDT > < Info > < HTTP > < NAP1D692 > < AdminServer > < [pending] ExecuteThread: '1' for the queue: '(self-adjusting) weblogic.kernel.Default' > < < WLS Kernel > > <><>< 1443734304863 > < BEA-101128 > < HTTP initialization services. >

    # < October 1, 2015 4:18:24 PM CDT > < Info > < HTTP > < NAP1D692 > < AdminServer > < [pending] ExecuteThread: '1' for the queue: '(self-adjusting) weblogic.kernel.Default' > < < WLS Kernel > > <><>< 1443734304894 > < BEA-101135 > < AdminServer is the default Web server. >

    # < October 1, 2015 4:18:24 PM CDT > < Info > < HTTP > < NAP1D692 > < AdminServer > < [pending] ExecuteThread: '1' for the queue: '(self-adjusting) weblogic.kernel.Default' > < < WLS Kernel > > <><>< 1443734304894 > < BEA-101052 > < [HttpServer (defaultWebserver) name: AdminServer] Initialized >

    # < October 1, 2015 4:18:24 PM CDT > < Info > < HTTP > < NAP1D692 > < AdminServer > < [pending] ExecuteThread: '1' for the queue: '(self-adjusting) weblogic.kernel.Default' > < < WLS Kernel > > <><>< 1443734304894 > < BEA-101129 > < init > the container of the Web application.

    # < October 1, 2015 4:18:24 PM CDT > < Info > < JMX > < NAP1D692 > < AdminServer > < ExecuteThread [ASSET]: '0' for the queue: '(self-adjusting) weblogic.kernel.Default' > < < WLS Kernel > > <><>< 1443734304972 > < BEA-149513 > < JMX Connector Server stopped serving: jmx:iiop://10.29.11.182:7001/jndi/weblogic.management.mbeanservers.edit. >

    # < October 1, 2015 4:18:24 PM CDT > < Info > < JDBC > < NAP1D692 > < AdminServer > < ExecuteThread [ASSET]: '0' for the queue: '(self-adjusting) weblogic.kernel.Default' > < < WLS Kernel > > <><>< 1443734304988 > < BEA-001144 > < Force suspending the JDBC service. >

    # < October 1, 2015 4:18:24 PM CDT > < Info > < JDBC > < NAP1D692 > < AdminServer > < ExecuteThread [ASSET]: '0' for the queue: '(self-adjusting) weblogic.kernel.Default' > < < WLS Kernel > > <><>< 1443734304988 > < BEA-001146 > < Force suspend completed JDBC service >.

    # < October 1, 2015 4:18:24 PM CDT > < Info > < JDBC > < NAP1D692 > < AdminServer > < ExecuteThread [ASSET]: '0' for the queue: '(self-adjusting) weblogic.kernel.Default' > < < WLS Kernel > > <><>< 1443734304988 > < BEA-001147 > < JDBC service stop. >

    # < October 1, 2015 4:18:24 PM CDT > < Info > < JDBC > < NAP1D692 > < AdminServer > < ExecuteThread [ASSET]: '0' for the queue: '(self-adjusting) weblogic.kernel.Default' > < < WLS Kernel > > <><>< 1443734304988 > < BEA-001149 > < stopping the JDBC service performed. >

    # < October 1, 2015 4:18:24 PM CDT > < Info > < JMX > < NAP1D692 > < AdminServer > < ExecuteThread [ASSET]: '0' for the queue: '(self-adjusting) weblogic.kernel.Default' > < < WLS Kernel > > <><>< 1443734304988 > < BEA-149513 > < JMX Connector Server stopped serving: jmx:iiop://10.29.11.182:7001/jndi/weblogic.management.mbeanservers.domainruntime. >

    # < October 1, 2015 4:18:24 PM CDT > < Info > < MessagingBridge > < NAP1D692 > < AdminServer > < ExecuteThread [ASSET]: '0' for the queue: '(self-adjusting) weblogic.kernel.Default' > < < WLS Kernel > > <><>< 1443734304988 > < BEA-200001 > < messaging bridge has shut down successfully. >

    # < October 1, 2015 4:18:24 PM CDT > < Info > < JMS > < NAP1D692 > < AdminServer > < ExecuteThread [ASSET]: '0' for the queue: '(self-adjusting) weblogic.kernel.Default' > < < WLS Kernel > > <><>< 1443734304988 > < BEA-040308 > < service JMS suspends >.

    # < October 1, 2015 4:18:24 PM CDT > < Info > < JMS > < NAP1D692 > < AdminServer > < ExecuteThread [ASSET]: '0' for the queue: '(self-adjusting) weblogic.kernel.Default' > < < WLS Kernel > > <><>< 1443734304988 > < BEA-040107 > < 8 cancelled by default connection factories. >

    # < October 1, 2015 4:18:24 PM CDT > < Info > < JMS > < NAP1D692 > < AdminServer > < ExecuteThread [ASSET]: '0' for the queue: '(self-adjusting) weblogic.kernel.Default' > < < WLS Kernel > > <><>< 1443734304988 > < BEA-040015 > < stop JMS is done >.

    # < October 1, 2015 4:18:24 PM CDT > < Info > < JMX > < NAP1D692 > < AdminServer > < ExecuteThread [ASSET]: '0' for the queue: '(self-adjusting) weblogic.kernel.Default' > < < WLS Kernel > > <><>< 1443734304988 > < BEA-149513 > < JMX Connector Server stopped serving: jmx:iiop://10.29.11.182:7001/jndi/weblogic.management.mbeanservers.runtime. >

    # < October 1, 2015 4:18:24 PM CDT > < critical > < WebLogicServer > < NAP1D692 > < AdminServer > < principal > < < WLS Kernel > > <><>< 1443734304988 > < BEA-000362 > <Server has failed. Reason: at least a migratable target is configured with automatic migration. Before the automatic migration of any type can be used, the MigrationBasis must be defined in the ClusterMBean. If database is chosen, must be set so DataSourceForAutomaticMigration. >

    # < October 1, 2015 4:18:25 PM CDT > < opinion > < WebLogicServer > < NAP1D692 > < AdminServer > < principal > < < WLS Kernel > > <><>< 1443734305003 > < BEA-000365 > < Server state changed to FAILED. >

    # < October 1, 2015 4:18:25 PM CDT > < error > < WebLogicServer > < NAP1D692 > < AdminServer > < principal > < < WLS Kernel > > <><>< 1443734305003 > < BEA-000383 > < is not an essential service. The server shuts itself down. >

    # < October 1, 2015 4:18:25 PM CDT > < opinion > < WebLogicServer > < NAP1D692 > < AdminServer > < principal > < < WLS Kernel > > <><>< 1443734305003 > < BEA-000365 > < Server state has changed to FORCE_SHUTTING_DOWN. >

    # < October 1, 2015 4:18:25 PM CDT > < Info > < WebLogicServer > < NAP1D692 > < AdminServer > < ExecuteThread [ASSET]: '0' for the queue: '(self-adjusting) weblogic.kernel.Default' > < < WLS Kernel > > <><>< 1443734305003 > < BEA-000236 > < stop run > discussions.

    # < October 1, 2015 4:18:25 PM CDT > < Info > < WebLogicServer > < NAP1D692 > < AdminServer > < principal > < < WLS Kernel > > <><>< 1443734305003 > < BEA-000238 > < judgment made. >

    It may sound crazy that I am answering my own post.  As he complains about MigrationBasis.  I tried to go to the config.xml file and changed

    Cluster-0

    unicast

    database

    TO

    Cluster-0

    unicast

    consensus

    And at least I was able to restart Server Admin and go to the Server Admin page. The Cluster-> Configuration-> Migration is always on view from database as the basis for Migration.

    Joe

  • The MAF project has been configured with an unsupported JDK

    Hello

    I am facing problem in jdevloper for implementation of the MAF. I have provided the JDK 1.8 version. But it still gives the following error.

    'D:\Jdev ADF Home\mywork\MyMobileApp\ApplicationController\ApplicationController.jpr' project has been configured with an unsupported JDK.  Make sure that the "profile 2 Compact MAF JDK 1.8 & quot; is used.

    Type or a variable 'oracle.adfmf.application.LifeCycleListener' not found.

    Jdev Version: Studio Edition Version 12.1.3.0.0

    Extension of the MAF: 2.1.0.0.41.150115.1352

    Please suggest me to fix this problem.

    Thank you

    SAN

    Simply change name Java SE 1.8.0_40 to the MAF JDK 1.8 Compact 2 profile

    I guess it will solve your problem.

  • vCAC 6.0 - shared configuration with separate infrastructure

    Hello

    I've been playing with vCAC 6.0 on my lab environment, and have a few questions related to the configuration shared with separate infrastructure.

    In literature, there is a section that explains the difference between a single and shared tenant configuration and within several tenants, the section explains two different - one configuration with the configuration of the shared infrastructure, and 1 vote against and separate infrastructure on each tenant.

    I was able to install all the components of vCAC 6.0 and have been playing with assignment of permissions tenant Admin and Admin infrastructure (IaaS) on different tenants. I added the end point of vSphere (vCenter) to the default configuration of the tenant (vsphere.local) and created the tissue group. Then I disconnected, navigate to the URL of the other tenant (calling it "Tenant LAB") and connected as an Admin IaaS. What I found was that the IaaS Admin LABORATORY tenant could see and edit the configuration details of the powers/group configured by IaaS Admin tenant default endpoint/fabric point. Surely, the other tenant IaaS Admin shouldn't be able to mess around with the settings made by IaaS Admin in the default tenant?

    I also found that when I added a point to endpoint/fabric group/diploma config for a default tenant (calling it 'Tenant 1') and then Administrator of another tenant IaaS (again, by default, describing it as "tenants 2"), IaaS Admin of the tenant 2 has been able to change the configuration of the group point of termination/references/fabric made by IaaS Admin in 1 tenant. That begs the issue of infrastructure configuration how isolated is between tenants in vCAC. The configuration of the Infrastructure is supposed to be shared like this?

    Thanks in advance

    The behavior you described is the expected behavior of the system. Currently, there are very strong tenant isolation in the catalogue of services, end-user features and business groups. However, infrastructure (endpoint points, groups of tissues, of identifying information) will be shared by tenants. I think a separate infrastructure is more in what the logical configuration of an endpoint, fabric/to be used only by a tenant Group bookings and another point of termination/reservations to be used by another tenant. This should be applied to a configuration at the tissue level, and it is not enforced by the system. Again, isolation would be reached at the end user level / service catalogue, where users of a tenant would be able to use and bookings resourcea configured for their tenants only of requests.

  • A no matter what you have ESXi 4.1 configured with HP SIM and system home page?

    Does anyone have ESXi 4.1 configured with HP SIM? I installed ESXi 4.1 with the HP Agents but must monitor via HP SIM so that we can monitor the hardware. Also is there a way to get the home page of the HP system to appear on port 2381? Or which is no longer available with ESXi 4.1?

    For information about how to configure HP - SIM, take a look at http://communities.vmware.com/message/1590665

    The homepage of management is only available for ESX, not for ESXi.

    André

  • E.M.P. 11.1.2.2 configuration with SQL Server 2008 R2

    Hello

    I was wondering if he should place the sqljdbc4.jar under any folder EPM_HOME\MW file to connect to SQL Server 2008 when you configure using the EMP system configurator.

    I'm just be proactive and ask the question because I had to do the same thing when configuring with SQL Server 2008R2 ODI...

    Looks like Oracle don't like MS and visa versa... Why not include just this file JDBC installation.

    Thanks in advance!

    No you shouldn't need drivers for sql server additional to configure SQL SERVER in the configurator to EMP they are included as part of the configurator.

    See you soon

    John
    http://John-Goodwin.blogspot.com/

  • Fate of automatic configuration with State 1

    Hello

    After you apply T2K patch 6372396 when I tried to run the autoconfig his mistake to launch the message in the file autoconfiglog below

    -----

    The following report lists the errors autoconfig met in each
    execution phase. Errors are grouped by directory and by phase.
    The format of the report is:
    & lt; filename & gt; & lt; phase & gt; & lt; code back, the case & gt;


    [PROFILE PHASE | http://forums.oracle.com/forums/]
    AutoConfig could not successfully run the following scripts:
    Directory: / xxx/app/xxxx/admin/install/xxxxx



    bisdblrp.sh; INSTE8_PRF 1



    Fate of automatic configuration with State 1


    Patch was completed successfully with warnings,

    Applications: 11.5.10.2
    OPERATING SYSTEM: HP UX

    Published by: appsguyflorence on November 11, 2008 02:41

    Appsguy,

    Can you please mark the thread as an answer.

    Thank you.

Maybe you are looking for

  • Firefox 4 will be improved or should I live somewhere else?

    Since the update to F4 internet crashes regularly, correspondence on new sites are ridiculously slow and clicks take ages to turn on. So, as much as I liked Firefox in the past is it time to say goodbye or it will be fixed?

  • Real-time application does not work; source code works very well

    The short version is I'm programming a cRIO and apparently the RT code isn't running after you deploy, and I can't understand why. It is further complicated as I do all this remote and I don't have direct access to the unit since I am 500 miles away.

  • 1344 error during install

    I got 1344 error during the installation of the software.  The missing indicated messsagefile Data1.cab.  I am running Windows 64 home premium.

  • Nc6400 - update BIOS issue?

    Hello I have a NC6400 and on a recent vist the site "Download drivers and software" for my laptop, I noticed that there was an update for my BIOS. My mobile is the version of April 16, 2007 f.0Une and the new verson is F.0B September 5, 2007. However

  • was a Director but lost? Why &#62; how do I get it back? __

    now have a standard account and an account invited but lost my original administrative account! How can I get rid of the standard and comments and retrieve my admin? I am alone here! Chris Brandon