Configuration WRT310N problem

Similar Questions

• URL WRT310N problem

  Well, this is my second WRT310N (version 2), I couldn't believe that this thing was so bad that he acted with the first one I got (and back), so I try again.

  The first thing I get after the router has been completely configured, internet "worked" was:

  URLThe Invalid URL requested ' / ', is not valid.

  Reference #9.6c6d1160.1250371680.0

  by clicking on my bookmark yahoo.com or hit 'home' on any of my browsers (Chrome, Firefox, and IE8 all "original" is set to www.yahoo.com).  I have ping would be yahoo.com in a window DOS command and got the IP digital and was able to go.  But not from www.yahoo.com.  And other URL like google.com, facebook.com, etc are fine.  Same "us.yahoo.com" works very well.

  Only a reboot will fix it.  And then only for a while... 20 minutes later, I have experienced the same problem, click on yahoo.com and get "invalid URL".

  Has anyone else experienced this problem and solved, or Version 2 of this router is just a piece of junk?

  I'm perfectly willing to work with this, but it goes back to the store pretty soon if I can't get out of frequent reboots.  If it wasn't the second router I had who encounters this problem, I have undertaken my own mental health.

  Thank you.

  -Roger

  Yes, when I disabled the firewall and antivirus disabled, my regular www.yahoo.com link was broken again.

  I solved this problem by opting for a Dlink DIR-655 Router, no problems now.  I can go wherever I want to, I have the gigabit wired ports that I was looking for, and I have n wireless.  It's nice not to have to wince before clicking on a URL.

  I think that there is something seriously wrong with the firmware for version 2 WRT310N router.  Or maybe I had 2 guys that Linksys extinguish.  I'm dubious on this subject, I have it from very different sources.  I have not seen the specific problem I had with the WRT54GS Linksys or Dlink DIR-655, so I'm pretty darn sure that points to the problem being the version router WRT310N 2 somehow.

  Thank you for trying to help, there is no help for this problem.  I really tried to make the WRT310N I got work, both were defective in exactly in the same way, this is why I finally gave up.

  -Roger

• Connection WRT310N problems

  Recently (in the last month or almost) I had problems with my router.  My connection suddenly stops working and I have to reconnect to the internet, I will join the game servers with ping around 20-40 and get "connection interrupted" put warning all the minutes, and the loading of web pages has gotten slow.  It doesn't matter how I am to the router, I still have these problems.  First, I thought that maybe it's my wireless card, but my friend ended and had the same problems.  I've had my router for a few years now and I was wondering if it was just getting old and needs to be replaced.  Is that what I can do to solve this problem or do I need a new router?

  I had a similar problem and the solution is actually quite simple, but it will be absolutely empty of any warranty. all those who say that it is a firmware issue is only listening for people who do not want to admit the necessity of a reminder. Depending on the router you have (V1 or V2) there are several used capacitors. V1 of this router has 6 selections and V2 4. These capacitors are horrible quality and usually a failure during several months of use. If you have the courage and an iron solder, go to radio Shack (or online if you want the best quality) and buy some new hats and replace the OEM ones. It took maybe half an hour and I've never replaced the components of the front card. After this replace my wireless connection is actually faster than before (objectively, no data to back up that) and the connection has not yet abandoned.

  some good info if you plan to go this route:

  www.badcaps.NET

  Council WRT310N V1

  

  WRT310N V2 (this shows the new capacitors, I installed. ugly, I know, but it works.)

  

• Configuration WRT54G problems

  I put my WRT54G Router returned to service after two years somewhere else. Configuration went well up to a point, but I'm unable to change the settings (at least) two areas of wireless configuration.

  First of all, the router is now set to WPA Personal and I want to change my personal WPA2. In the basic/WIreless wireless settings page, I choose WPA2 from the drop-down list box, but he immediately returned to WPA. Second, I want to restrict the use of a specific set of MAC addresses. Wire/Wireless MAC Filter, I can click on the 'Enable' radio button, but it jumps to "turn off" immediately.  Powering everything down, leaving everything and restarting has no effect.

  The bottom of the router is marked WRT54G V8 and the status page displays FIrmware Version: v8.00.0, January 16, 2007. I thought that a firmware update might be in order. Downloads WRT54G (http://www.linksys.com/us/support-article?articleNum=148648) shows version numbers upward through 8.2, but nothing in 5.0 and above says, "No download of the firmware/driver available." Version 4.0 offers v4.21.5 (24/02/2012). What is the current version of the firmware? Seems a lot lower than 8.00.0.

  Firmware upgrade or not, I want to be able to change the wifi settings.

  Options?  Thank you.

  I use a wired to the router, even if it goes through another router first as an additional firewall. I did the hard reset twice with no improvement in the situation.

  Then I discovered the problem: for some bizarre reason, Linksys requires cookies to make changes on the mode of security and MAC, filtering of the screens. I use a strict cookie Manager in Firefox, and once I have authorized temporarily cookies all went well.

  Sorry for the misdirection.

• Wireless network connection is not a valid IP configuration / wifi problems

  I recently bought a laptop Asus G74 from Best Buy. It is currently running Windows 7 x 64 home premium. I am away from home on a job to work on a project for my company and during the two weeks have stayed at the same hotel with the same wireless, leaving home for thanksgiving between stays. The first week I spent the unsecured WiFi, download programs and games and play. I left the House, returned and used the wifi day, realized there is an ethernet cable in my computer bag laptop and connected to the hard line for the next day. I went to a colleague of room (a room down), went to look for the WiFi, and the trouble started.

  Diagnostics Windows network tells me that the wireless network connection is a valid IP configuration. I thought it would be something to do with the drivers, so I opened by Device Manager, went through each of my NICs 5 or more and look for the updates of drivers. A couple said they have successfully installed, but nothing has changed my ability to connect. Then I thought about rolling back the drivers, but since I've had the laptop for such a short time (less than 30 days) the option is grayed out. It wouldn't make sense since I could connect the previous week on the same wireless.

  From there, I decided to try a system restore to a point when I was getting into at first hotel. Restarting the laptop and the restore was successful. I tried to log in again and the same problem arises. I downloaded a couple of my favorite, Malwarebytes, and SUPERantispyware tools. Both have nothing.

  So I did some research and digging and scholar on ipconfig (flushdns / release / renew) with an elevated command prompt. I tried these and they told me my media is "disconnected" and cannot be released or renewed. I found this strange since I can see the wifi network. I tried to use the Fn + F2 to toggle the wifi and WIMAX (no idea which is incidentally) with simple ipconfig and media disconnected status does not change. I also read that disabling ipv6 might help, so I did this and still no dice. I restored system again for the 2nd point earlier and it still does not connect.

  Drop-down wifi icon in the bottom right of the screen, after trying to connect to the network unsecured wifi here (BWCamarilloInn), it reads 'Unidentified network' and under it "no internet access. I had different flavors of this message, including "limited access".

  I thought I'd try a cross-check to see if it was not on the end of the hotel. I pulled out my laptop backup enterprise and was able to immediately connect to the wifi, and my colleague from work related to his phone and his netbook. I saw another thread somewhere on a Windows forum that suggests a clean boot. Tried, has not changed anything either.

  Currently I have about 5 different adapters according to the Windows Network Diagnostics: the 1/2 LAN connection and Wireless Network Connection 1/2/3.
  I also have 5 in the drop-down list of the network adapters in the Device Manager.

  Intel Centrino WiMAX 6150
  Intel Centrino Wireless-N 6150
  Microsoft Virtual WiFi Miniport adapt
  Microsoft Virtual WiFi Miniport adapt #2
  Realtek PCIe GBE Family Controller

  and a separate drop-down list called adapters Intel Centrino WiMAX, with a menu drop down called function Intel® Centrino WiMAX 6150 driver.
  They are all updated when right click and check for driver updates.

  I also looked through the different adapters and checked to see if the ipv4 settings have been defined to automatically detect the IP of/etc.

  The laptop is great and I wouldn't really have to take it back to Best Buy. Other problems seem to be of culture that may be useful to know. Patch of League of Legends sometimes throws me an error "kernel patch pvp.net has stopped working", or just sits on the main projection before it hits the pitcher. Sometimes, it goes past the pitcher and he's here without connect to or start the main game. I heard that this has to do with the network stuff. I am computer literate, but I'm not terrible with networking or internet configuration stuff. If anyone can give me a hand, that would be much appreciated. I'll help you as much as I can. I've also attached the current ipconfig info (I'm connected to the internet via an ethernet to the wall cable, League of legends should therefore be able to launch).

  Thanks in advance.

  -Chris

  ipconfig Info

  Microsoft Windows [Version 6.1.7601]
  Copyright (c) 2009 Microsoft Corporation.  All rights reserved.

  C:\Windows\System32>ipconfig

  Windows IP configuration

  Ethernet connection to the network space 2 card:

  State of the media...: Media disconnected
  The connection-specific DNS suffix. :

  Wireless Network Connection 3 Wireless LAN adapter:

  State of the media...: Media disconnected
  The connection-specific DNS suffix. :

  Wireless Network Connection 2 wireless LAN adapter:

  State of the media...: Media disconnected
  The connection-specific DNS suffix. :

  Wireless network connection Wireless LAN adapter:

  State of the media...: Media disconnected
  The connection-specific DNS suffix. :

  Ethernet connection to the Local network card:

  The connection-specific DNS suffix. : nomadix.com
  Link-local IPv6 Address...: fe80::d572:64 c 9: d97c:1f0a % 11
  IPv4 address...: 10.0.0.45
  ... Subnet mask: 255.255.255.0.
  ... Default gateway. : 10.0.0.4.

  Tunnel adapter ISATAP.Nomadix.com:

  State of the media...: Media disconnected
  The connection-specific DNS suffix. : nomadix.com

  Tunnel adapter isatap. {0B9C8743-1CDE-4BFF-9FDD-153D2D44F596}:

  State of the media...: Media disconnected
  The connection-specific DNS suffix. :

  Tunnel adapter isatap. {FD7B8B70-2937-4816-B45C-B73104366373}:

  State of the media...: Media disconnected
  The connection-specific DNS suffix. :

  Card tunnel Teredo Tunneling Pseudo-Interface:

  The connection-specific DNS suffix. :
  IPv6 address: 2001:0:4137:9e76:423:3796:f5ff:ffd2
  Link-local IPv6 Address...: fe80::423:3796:f5ff:ffd2 17%
  ... Default gateway. : ::

  Tunnel adapter isatap. {33A5C370-7EBC-4E95-A9AD-C7F3BF5D373E}:

  State of the media...: Media disconnected
  The connection-specific DNS suffix. :

  Tunnel adapter isatap. {501554B1-09E9-49B0-9078-04D0ADBD48A1}:

  State of the media...: Media disconnected
  The connection-specific DNS suffix. :

  C:\Windows\System32 >

  Edit
  minor changes to the grammar/punctuation

  Hey, sorry for the slow response. Just got home a few days, and since then, I've been able to connect both the wifi just next door (I'm on the end furthest from the beach with her, but I can still connect) and on my netgear n wireless router. I can also access the router dashboard. Fail to starbucks so just wifi next door was the next best thing. ASUS finally answered after 11 days, saying I should reinstall the wireless driver, which I told them was one of the first things I did. Well. It seems that the hotel wifi and I have no idea why this is the case. I was able to connect to the wifi at the hotel the first week and not the second while they might have changed something. I have no idea. I'm just glad that it connects to other networks, both guaranteed and no guaranteed. I'm just a bit worried that it might happen again in the future but I always wear a hard line in the event of an emergency and a business laptop backup.

  With this new information, should I worry still try to fix anything with the hotel wifi, or do I just leave it as is? Thanks for the support continuous, 100 times better than ASUS right now: P

  -Chris

• Access to an external table via the display in the UCM configuration manager problem

  Hi all

  I know that this question is already asked here: to access the external tables in DB / in UCM Applet configuration manager but the conversation has already been archived, and I can't comment there. I'm following approach given by William Phelps in above said archived thread.

  I am able to create dblink with data remote and created the view by using the linked table in my diagram of the Complutense University of Madrid. The problem that I face is that this point of view such as told by William is not visible in the configuration manager. Although I tried to give (create view and create all views) system diagram University Complutense of MADRID user privileges, but I'm not sure that it will also provide access rights. I am using the SQL Developer and working at the University Complutense of MADRID 11 g.

  All comment or suggestion will be a great help.

  Stéphane yapi

  The value of this configuration variable: EBRIncludeViewsInTableList = 1

  https://jonathanhult.com/blog/2013/11/use-database-view-WebCenter-content-schema-view/

  Jonathan

  http://jonathanhult.com

• Detected incorrect configuration error - problem of multicast?

  I saw a mistake 'Has detected a misconfiguration' after scoring in the Web client, select a cluster, the tab manage, settings, Virtual SAN subtab-> general.  He went after activating the traffic on the vmk0 VSAN management interface.  I found that by vSphere 6.0 Documentation Center, 'Network Misconfiguration in a Virtual SAN Cluster status' it was probably due to a bad configuration of the multicast.

  I talked to my network admin, who made sure IGMP Snooping has been disabled, and I turned off VSAN, then again once and the error disappeared temporarily.  However, when you choose inside on a specific host a cluster, I still see "host cannot communicate with all other nodes in the active SAN virtual cluster.  The "Misconfiguration detected" error is returned.

  1 is a multicast group must be configured to work?  I am referring to vSphere 6.0 Documentation Center, "Modes of filter Multicast", where it is said:

  Filtering basic multicast mode a Standard switch or Distributed Switch vSphere vSphere transmits multicast traffic for virtual machines based on the destination MAC address, of the multicast group. When you join a multicast group, the guest operating system pushes the MAC address of the multicast group down to the network through the switch. The switch saves the mapping between the port and the destination multicast MAC address in a table of local transfer.

  
  

  I guess that does not apply to the VLAN that I've dedicated to VSAN multicast traffic, where IGMP Snooping should be disabled?

  
  

  
  

  2 cannot not set port 4095 to enable all the VLAN resources shared - is it necessary?

  I thought that when you configure the network on the ESXi server, I thought I should specify 4095 to VLANS allow all trunking 802. 1 q VLAN through.

  As:

  -the documentation I found only goes to 4094 and

  -in the ESXi console, I entered 4095 to the VLAN ID (which failed),

  is the VLAN ID of the management network is good?  Or could it be that traffic for that VLAN even get through on the server because of this?

  3 here is what I understand VMware in terms of this error:

  Cluster form--nodes will not be able to communicate - Has detected a misconfiguration

  – Option 1 -Disable IGMP Snooping = > allows to all the through the multicast traffic

  – Option 2 -Configure IGMP Snooping Interrogator = > if there is another multicast traffic and you fear that multicast traffic could flood network

  
  

  
  

  
  

  
  

  
  

  I also had this link to what is required by the side of Cisco, but it does not (gives 404 error).  Can someone give instructions that work?
  

  http://www.Cisco.com/c/en/us/TD/docs/switches/Datacenter/SW/nxSos/multicast/configuration/guide/b_multicast/b_multicast_chapter_011.html

  
  

  
  

  
  

  
  

  
  

  4. by comparing the results of two servers, they cannot ping each other (addresses 10.27.98.7 *) on vmk1.  My network engineer said that the switchports are that all configured the same.  Any thoughts on why they can't ping?

  [root@host05:~] esxcli ip interface ipv4 network get

  DNS name IPv4 address IPv4 subnet mask IPv4 address Type DHCP broadcast

  ----  ------------  ---------------  --------------  ------------  --------

  vmk0 10.27.98.199 255.255.255.192 10.27.98.255 fake STATIC

  vmk1 10.27.98.71 255.255.255.192 10.27.98.127 fake STATIC

  vmk2 10.27.98.136 255.255.255.192 10.27.98.191 fake STATIC

  [root@host05:~] vmkping - I vmk1 10.27.98.71

  PING 10.27.98.71 (10.27.98.71): 56 data bytes

  64 bytes from 10.27.98.71: icmp_seq = 0 ttl = 64 time = 0,096 ms

  64 bytes from 10.27.98.71: icmp_seq = 1 ttl = 64 time = 0.084 ms

  -10.27.98.71 - ping statistics

  2 packets transmitted, 2 packets received, 0% packet loss

  round-trip min/avg/max = 0.084/0.090/0.096 ms

  [root@host05:~] vmkping - I vmk1 10.27.98.70

  PING 10.27.98.70 (10.27.98.70): 56 data bytes

  -10.27.98.70 - ping statistics

  3 packets transmitted, 0 packets received, 100% packet loss

  [root@host05:~] vmkping - I vmk1 10.27.98.71

  PING 10.27.98.71 (10.27.98.71): 56 data bytes

  64 bytes from 10.27.98.71: icmp_seq = 0 ttl = 64 time = 0.088 ms

  64 bytes from 10.27.98.71: icmp_seq = 1 ttl = 64 time = 0,074 ms

  64 bytes from 10.27.98.71: icmp_seq = 2 ttl = 64 time = 0,081 ms

  -10.27.98.71 - ping statistics

  3 packets transmitted, 3 packets received, 0% packet loss

  round-trip min/avg/max = 0.074/0.081/0.088 ms

  [root@host04:~] esxcli ip interface ipv4 network get

  DNS name IPv4 address IPv4 subnet mask IPv4 address Type DHCP broadcast

  ----  ------------  ---------------  --------------  ------------  --------

  vmk0 10.27.98.198 255.255.255.192 10.27.98.255 fake STATIC

  vmk1 10.27.98.70 255.255.255.192 10.27.98.127 fake STATIC

  vmk2 10.27.98.135 255.255.255.192 10.27.98.191 fake STATIC

  -10.27.98.70 - ping statistics

  3 packets transmitted, 3 packets received, 0% packet loss

  round-trip min/avg/max = 0.072/0.080/0.089 ms

  [root@host04:~] vmkping - I vmk1 10.27.98.71

  PING 10.27.98.71 (10.27.98.71): 56 data bytes

  64 bytes from 10.27.98.71: icmp_seq = 0 ttl = 64 time = 0,726 ms

  64 bytes from 10.27.98.71: icmp_seq = 1 ttl = 64 time = 0,362 ms

  64 bytes from 10.27.98.71: icmp_seq = 2 ttl = 64 time = 0.561 ms

  -10.27.98.71 - ping statistics

  3 packets transmitted, 3 packets received, 0% packet loss

  round-trip min/avg/max = 0.362/0.550/0.726 ms

  
  

  
  

  
  

  
  

  
  

  PS: this certainly looks like a network configuration problem

• [EMP Configuration] OracleDB - problem of Configuration of OC4J... not found

  Hello
  
  Constantly reviewing the existing solutions for this issue, I find that mine is not yet displayed.
  
  Intro
  In order to install EPM, I had to install Oracle Database 11 g. After installation, an error has occurred, stating that configurations were not saved and I could manually run "ECMA.bat" later.
  I tried to configure by creating environment variables such as:
  -ORACLE_SID
  -ORACLE_HOSTNAME
  -ORACLE_UNQNAME
  
  So far, I have not tried to run ECMA.bat for the last time, because I'm sure that I will not fail due to not recognize the host name.
  
  
  The question
  Whili trying to make sure that the database is properly set up, I tried to access the Web page, to no avail.
  Then, I found my problem in the forums:
  
  When I type cmd:
  
  -> (Type I)
  C:\OracleDB_app\alexandreyin\product\11.2.0\dbhome_1 > emctl status dbconsole
  
  -> (returns)
  OC4J Configuration problem. C:\OracleDB_app\alexandreyin\product\11.2.0\dbhome_1/o
  c4j/J2EE/OC4J_DBConsole_HPCM. Lab.pt_orcl not found.
  
  
  In fact, there is no file with this name, or something like "/ OC4J_DBConsole_localhost_orcl" suggests that many positions.
  I only have folders like:
  -' House '.
  -"oc4j_applications".
  -"OC4J_DBConsole".
  -"OC4J_Workflow_Component_Container".
  -"OC4J_Workflow_Management_Container".
  -"utilities".
  -"deploy_db_wf".
  
  Some posts suggesting to change me my file/driver/etc/host, but I think that my current file is correct:
  
  -> (Contents of host gile)
  127.0.0.1 localhost
  XX.XXX.XXX.XXX HPCM.lab.pt
  
  
  Honestly, I'm out of ideas and I wish all experienced colleague could give me a hint.
  
  
  Thanks in advance

  Hello

  It is useful to have a look at the next on Oracle support document.

  Problem - emctl start dbconsole fails with the problem of the OC4J Configuration OC4J_DBConsole__ not found error * [555218.1 ID] *.
  Linux 64-bit DBConsole fails with "cannot find/oc4j/j2ee/oc4j_DBConsole_... OC4J Configuration problem ' * [462325.1 ID] *.

  Thank you
  HyperEPM

• Configuration ethernet problems

  Have problems to connect via Ethernet to a LOGO! 12 / 24RCEo Siemens

  Ethernet IP = 192.168.0.2

  subnet = 255.255.255.255

  LOGO = 192.168.0.1 IP

  subnet = 255.255.255.0

  Maybe I should switch Ethernet subnet. How?

  Choose "Using DHCP" if possible. The computer is better to choose a usable IP address that you are.

• VCAC configuration: interface problems

  Hello world

  After completing the installation of the vCAC and start the configuration, I got this (screenshot) in the infrastructure tab.

  Someone knows what may cause this? the error says "file or directory not found" I think it's a HTTP 404 ERROR, but I don't know which file is missing...

  

  Thank you

  You restart the computers GOING and IaaS?

• Configuration network problem

  Hello world!

  I have the following Setup: a virtual server with network three ports eth0 and eth2. eth0 is used fpr administration of the VServer.

  eth1 is disabled. Now, I have configured eth2 as a bridge to the virtual machines. For now, it works pretty well with

  exactly one IP configured on the host computer for eth2. Now it is true that there are several more mapped IP addresses

  on eth2. The amount of these IPs may change over time, and I don't want to configure the interface on the host

  whenever I listen to new addresses. These IP addresses are all on the same network using the same program and

  subnet and gateway. So my question is:

  How should I configure eth2 on the host (debian) system for all incoming traffic on eth2 is filled to the virtual machines?

  Thanks a lot for your help.

  orkano

  PS: Here is my file interfaces:

  This file describes the network interfaces available on your system

  1. and how to activate them. For more information, see interfaces (5).

  1. The loopback network interface

  Auto lo

  iface lo inet loopback

  1. The main network interface

  Auto eth0

  iface eth0 inet static

  address XXX. XXX.226.101

  subnet mask 255.255.252.0

  dissemination of XXX movies. XXX.227.255

  Portal XXX. XXX.224.1

  Auto eth2

  iface eth2 inet static

  address XXX. XXX.246.10

  netmask 255.255.255.0

  dissemination of XXX movies. XXX.246.255

  Portal XXX. XXX.246.1

  Welcome to the forums!

  orkano wrote:

  How should I configure eth2 on the host (debian) system for all incoming traffic on eth2 is filled to the virtual machines?

  You must run ' vmware - config.pl ' to configure virtual networking. Then you choose eth2 as your adapter to fill. That's it for the side host. The customer must have a vNIC, type "bridged" and their own IP configuration valid IP range of the physical network subnet where eth2 is attached to.

  That answer your question, or have I missed something?

  AWo
  VCP / VMware vEXPERT 2009

  = Due to a lack of employees, human beings humans are working here. -Treat it with care, they are rare. =

• Deployment configuration Assistant problem

  I did everything up to the point where I enter the IP address of the Simulator, but it returns the following error:

  "Unable to connect: connect to /192.168.xxx.xxx:443 has expired.". Check the settings of IP address for the target. You may need to restart the target. »

  NB: I tried to restart, but that has not worked.

  What you can try to do is to change your network settings of your vmware to use a bridged instead of NAT network.
  Stop the Simulator and then search for the settings option. Under network, select settings jumpered. Resart the Simulator.

• Problem with GANYMEDE + (ACS) and cat 2950

  I have configured the 2950 as below and properly configured ACS and I can connect to the 2950 using this configuration, the problem lies after that I go to enable and try any command, I get approval to next error command failed.

  What I missed out the config that will allow me to execute commands?

  AAA new-model

  AAA authentication login default group Ganymede + local

  AAA authorization exec default group Ganymede + local authenticated by FIS

  AAA authorization commands 15 default group Ganymede + authenticated if

  AAA authorization network default group Ganymede + local authenticated by FIS

  AAA accounting exec default start-stop Ganymede group.

  orders accounting AAA 15 by default start-stop Ganymede group.

  AAA accounting network default start-stop Ganymede group.

  GANYMEDE server host ***. ***

  radius-server key 7 *.

  Thanks in advance.

  Jon

  Hi Jon,

  AAA of the switch seems ok, maybe you need to take a look at your ACS.

  Check the following information, where you have to apply it in your ACS config:

  http://www.Cisco.com/en/us/products/sw/secursw/ps5338/products_configuration_guide_chapter09186a00801fd6fc.html#wp676529

  Rgds,

  AK

• Restore the configuration of the AIP-SSM20?

  Hi there

  I have a small problem here - we are in the phase inupgrading of our Firewall to a set of 5510 with SSM10 to a set of 5520 with SSM20 - and I expected, it was quite simple just restore the current configuration of the SSM10 on the SSM20'- and weel - looks too so when I copy everything my server configuration ftp in backup-config and then load the backup current config with deletion - but when I look at by the After he was replaced in the configuration of the network?

  I use the version 7.04 (E4) the kernel he...

  The anyoine there have attempted to backup and restore the complete configuration - without problems?

  If I copy the restored configuration back and do a diff on them the difference lies in the service host section:

  2V2

  < !="" current="" configuration="" last="" modified="" wed="" jun="" 22="" 23:42:31="">

  ---

  > ! Current configuration changed the sea Mar 30 15:03:54 2011

  8 C 8

  < !    ="" signature="" update   ="" s573.0  ="">

  ---

  > !     Update of the signature S561.0 2011-04-20

  34 c 34

  < service="">

  ---

  > service host

  36 c 36, 38

  < host-ip="">

  ---

  > host-ip x.x.x.42/24,x.x.x.1

  > host name of fw_pri Internet service provider

  > telnet-option enabled

  a 37, 40, 54

  > dns primary server enabled

  > address 8.8.8.8

  > output

  > dns server secondary disabled

  > dns server service disabled

  > output

  > time-zone settings

  > offset 60

  > standard time - GMT + 01:00 area name

  > output

  > ntp-option enabled-ntp-no authenticated

  > ntp server - 193.162.145.130

  > output

  > automatic update

  > cisco-server disabled

  is this a known issue?

  best regards /ti

  we are in the phase inupgrading our firewalls from a set of 5510 with SSM10 to a set of 5520 with SSM20 - and I expected it was quite simple just to restore the current config from the SSM10 on the SSM20'es

  Fix. You should be able to restore a backup of configuration of the sensor of the AIP-SSM-10 on a module of sensor AIP-SSM-20 without much trouble, although hardware-wise that the AIP-SSM-20 are more able/powerful, there is no difference in the interface (or quantity) naming conventions, etc. that was displayed in the configuration.

  I expected it was quite simple just to restore the current config from the SSM10 on the SSM20'es - and weel - it also looks so when I first copy the config from my ftp-server to the backup-config and then load the backup to current config with erase - but when I afterwards look in the network configuration it has been replaced?

  I'm not sure that I followed exactly the procedure that you tried, but you should be able to back up the current configuration of the AIP-SSM-10 sensor module to a remote server, and then copy from the remote server to sensor AIP-SSM-20 module. Example:

  AIP-ssm-10 # copy current config

  AIP-ssm-20 # copy current-config /erase

  NOTE: The parameter/erase applies only to the current config. If specified for the current-configdestination, the configuration of the source is applied to the default configuration of the system. If it is not specified for the current-configdestination, the configuration of the source is merged with the current config. Maybe that is part of the confusion?

• SG300 voice vlan problem with UC520

  Salvation of the Forumers

  My problem statement:

  -Secretary referred to topology.png, this is how my network like structure look

  -the IP phone after startup can not connect, so it cannot download the XML of UC520 configuration file. problem switching suspects.

  -my configuration illustrated in topology.png and my config show vlan as the voice setting.png voice vlan

  -My requirement is switch SG300 unique switchport to carry data VLANs and vlan voice.

  -What is the mode of connection for voice siwth VLAN an IP phone + data must be set up? is it switchport voice vlan vvid switchport voice vlan dot1p, switchport voice vlan unidentified or vlan switchport voice no further action over requirement?

  Thank you

  Noel

  Christmas morning,

  Sorry for the late reply, things have been very hectic in here lately

  1. Why use trunk? the UC520 don't have voice vlan (vlan 20)

  Do you mean that data THAT VLAN is handled by another device? Again I would like to leave as a trunk in order to manage the CPU through the data VLAN. (Except for security or other reasons you would choose differently of course)

  2. the UC520 got CUE (voicemail), how should I design the uplink service for the main switch module?

  Nothing in particular needs to be done for this, CUE is processed and routed inside the UC520, the vlan (default ID = 90) CUE is used if you have another LANDMARK in the network

  1. I guess I did: swithcport the tag vlan vlan unlabelled 20, 10. is it ok for this setting?

  If the Vlan on the switch and the UC520 voice has been defined as VLAN 20 (default value = VLAN 100) it's perfect. Check if the CPU and the switch, the voice VLAN ID is set to 20.

  1 so if I have just the phone to vlan 20 (vlan voice), create the policy of network LLDP?

  If you are ready to configure the VLANS manually on the phone, you don't need politics LLDP, thats right.

  Politics LLDP is used to having phones automatically choose the VLAN you set, so you do not need to set it manually.

  I hope that answers your questions?

  Best regards

  Nico glacier

  Senior Network Engineer - CCNA