Configure the public traffic network IP inside the internal network itself and not to the external network

A server is now accessible from external network access using the IP and port in browser below http
http://x.x.x.x:8080

For the same, we have configured (static NAT) port forwarding in cisco security 1905.

The application is also accessible via IP and the internal network port internal (ie. http://y.y.y.y:8080)

Is there a way I can configure my 1905 Cisco as well as internal network (ie. machine B) I can access the application using the IP and the public port and not with the IP address internal? From now on, I'm not able to do the same.

The current configurations are as follows:
access-list 1 permit y.y.y.0 0.0.0.255
IP nat inside source list 1 interface GigabitEthernet0/0 overload
IP nat inside source tcp static y.y.y.y 8080 interface GigabitEthernet0/0 8080

Hello

You can try Domainless Nat.

no nat ip within the source list 1 interface GigabitEthernet0/0 overload
no nat inside source tcp ip static y.y.y.y 8080 interface GigabitEthernet0/0 8080

int gig0/0
no nat inside ip
activate nat IP

int gig0/1
no nat inside ip
activate nat IP

IP nat source list 1 interface GigabitEthernet0/0 overload
interface IP nat source tcp static y.y.y.y 8080 GigabitEthernet0/0 8080

RES

Paul

Tags: Cisco Network

Similar Questions

  • I can't configure the external Vantec NBA-200U on my computer sound card.

    I can't get sound to work with this surround sound card. I have a 5.1 speaker logitech set hung up (via green, black and orange connectors for audio 5.1).  In the audio Panel in windows 7 (64 bit), on the reading tab, I see the USB audio peripheral speakers. When I set up the speakers and test them from the speaker configuration panel, I hear sound from right speaker when testing each. BUT when I play I can't hear the music by L R (stereo) speakers.

    Side note: when I plug the external sound Windows card automatically installs the driver. If I install the driver on the cd so I get an additional device in the audio Panel in the Read tab. This device cannot be configured. But when it is installed and I'm trying to set up the speakers and test (same as above) I can get stereo sound.
    Anyone out there have any ideas?
     
    Original title: Vantec NBA-200U external sound card

    Hi Johnny French,.

    Thanks for posting your query in the Microsoft Community Forums. If I understand you correctly, you a problem with the sound works not properly after connecting to a Vantec NBA-200U external sound card I understand it must be frustrating, but don't worry, we are here to help solve your problem and guide you in the right direction.

    We start with a few questions-

    (1) you are able to get the sound to work on another computer (running the same operating System )?

    (2) did you make changes on the computer?

    I would like more information about the issue.

    Now let us perform some troubleshooting. All steps are carried out systematically and in order.

     

    Method 1-

    I wish that you are running the FixIt-

    Diagnose and solve the problems of Windows audio playback automatically

    Hardware devices do not work or are not detected in Windows

    Method 2-

    I would have you look at the article-

    Tips for solving common audio problems

    Method 3-

    You have to put in day the latest drivers for the sound card.

    See the article-

    How to update a sound card driver in Windows Vista and Windows XP

    Note: Applies to Windows 7 .

    In addition, I would have you look at the manual for the sound card that could help you with the settings.

    If none of the steps help, then I would you contact Vantec support for assistance.

    Check out the link-

    http://www.vantecusa.com/en/support/index

    Do get back to us and let us know the State of the question in the case where you need further help or your next post.

     

    Hope this helps!

     

  • Time Machine does not recognize the backups when you configure the external drive as a network drive

    I have a MyBook 5 to disk with a 1 TB partition that I used as a destination for Time Machine > 1 year now. I recently gathered the energy to connect the my book on my Airport Extreme Base Station (model 2014? the second model) to implement wireless backups. I plugged the MyBook on the base station, set up file sharing in AirPort Utility and created an account with access to the partition of TM on the MyBook under the section 'Sharing secured disk' utility.

    Now, when I open the time Machine, I choose this partition, but it does not seem to recognize that I have a string of backups already there. Then he tries to start a new backup. So a few questions.

    1. Should I abandon my old backups and start over? I don't think that I did nothing to my system in these last days that I would need to be careful, if I couldn't rely on a TM backup from that moment.
    2. Is there a way to get TM to recognize my old backups and start from there? I do not look down the barrel of a backup of time + 13.

    If 1, should I reformat the partition TM in order to start over? I don't see the older backups on disk when I look in the Finder, but I know that they are there and they are too much space. Help/suggestions appreciated!

    Inherit from a backup

    Inherit from a backup (2)

  • What are the things to do and not do purge external hard drive?

    Well, now that I got the big breakthrough on my 1st question in another category, thank you Gerry (England) and Pa bear!  Now on what is probably extremely easy for you. I have an external hard drive and when I got this HP computer about 2 years ago, I took and put ALL of my old computer inside (not realizing I didn't need to put some programs/trash etc.) All I wanted was to put documents / my pictures etc, SO WHAT are the things and make my external hard drive purge? Thank you...   Kind REGARDS Nicole Ramirez

    P.S. did publish in the right category?

    What I would do is create a new folder, move to this folder the items I wanted to keep, and then delete all the rest or I would move to another disk (or temporary storage in the cloud) these elements, I would like to keep, quick-format of the disk and replace the kept items.

  • Can configure the server from the host with IP address

    Hello

    I want to configure a guest computer with 2 network cards, one for LAN private and one for the external LAN.

    Right now, the problem is that I don't have that 1 useable public IP I can use on the external network address.

    Which means that it's either I configure the public ip address on the NIC host or on the comment card.

    May I just know set network bridge on the guest computer and configure the external static public IP, and then click map NETWORK address of the host machine, I set up the ip address. Will this work?

    Please notify.

    shanmomo wrote:

    If you mean that by disabling TCP/IP on the host, the guest computer can access external WiFi?

    Yes, if you use a Windows host, just uncheck the TCP/IP on the bridged card.

    Or use NAT, then both machines can connect to the internet with a single IP.

    AWo

    VCP 3 & 4

    Author @ vmwire.net

    \[:o]===\[o:]

    = You want to have this ad as a ringtone on your mobile phone? =

    = Send 'Assignment' to 911 for only $999999,99! =

  • "Limited connection" when you configure the network between two computers XP.

    Original title: Configuration of the network connection

    Trying to establish a network connection between two home PCs., both running Windows XP Pro. Have been through the network on both PC Setup Wizard but, they still say limited, in fact no connection. I use an Ethernet cable between the two Crusader. If it is true what I'm doing wrong?

    Thanx Terry

    Old but good, networking tips from MVP Malke, MS:

    The best and simplest is to buy a wireless router. This way you get Internet connectivity both machines and the added benefit of security more between you and the Internet. Then you configure your network wireless safely, and then you configure file/printer sharing. Here is information on the implementation of a router and also in networking. It seems long, but don't be intimidated. Setting up a router and the LAN of sharing between two computers takes about 15 minutes.

    The router configuration

    Setting up a router is simple enough. Normally, you run the CD that came with the router and follow the instructions. If you're running Vista, maybe the CD that came with the router does not work; I do not know this. But you can set up the router without the CD. Note that if you have Internet cable for the connection you have just set up the router to DHCP (or there may even be a choice of cable to choose). If you have DSL Internet, you select TRP usually and enter the username and password you selected when you initially set the DSL connection. So:

    1. turn off the power to your cable modem.

    2. attach a cable (usually supplied with the router) course Ethernet cat5e Internet/WAN port of the router to the Ethernet port on the cable modem.

    3. connect the ethernet cable cat5e from the network card in your computer to one of the ports on the router. If you do not have an ethernet cable (because you were using USB), you will need to go to the store and buy a.

    4. turn on the cable modem. After that all the lights are on, turn on the router.

    To configure the router:

     

    Have a computer connected to the router with an ethernet cable. Examples given are for a Linksys router. See the manual of your router or the router mftr's Web site. for the parameters by default if you don't have a Linksys. Open a browser such as Internet Explorer or Firefox and in the address bar type:

    http://192.168.1.1 [Enter] (it is default IP address of the router, which varies from router to router then check your manual)

    This will bring you to the login screen of the router. The default username is blank and the Linksys default password is "admin" without the quotes. Enter this information. You are now in the configuration of the router utility. Your configuration utility may be slightly different from mine.

    Click the Administration link at the top of the page. Enter your new password. MAKE A NOTE SOMEWHERE THAT YOU WILL NOT LOSE. Re-enter the password to confirm it, and then click Save settings at the bottom of the page. The router will reboot and show you the box of connection again. Do not fill in the user name and put it in your new password to enter the configuration utility.

    Now, click on the link wireless at the top of the page. Change the network name (SSID) wireless by default to something, you'll recognize. I suggest that my clients not use their surname as the SSID. For example, you might want to name your network wireless network "CastleAnthrax" or similar.

    Click on save settings and when you get the prompt that your changes were successful, click the wireless security link which is just beside the Basic Wireless Settings link (where you changed your SSID). If you have a newish computer, you will be able to affect security WPA2-Personal Mode. Do this and enter a password. The password is what you enter on all computers that are allowed to connect to the wireless network. MAKE A NOTE SOMEWHERE THAT YOU WILL NOT LOSE.

    At this point, your router is set up and if the computer that you use to configure the router will normally connect wireless, disconnect the Ethernet cable and wireless of the computer should see your new network. Enter the password you created to join the network and start surfing.

    *****

    B. file/printer sharing of

    Excellent, comprehensive, but easy to understand article on sharing files/printer under Vista. Contains information about sharing printers and files, and the folders:

    http://TechNet.Microsoft.com/en-us/library/bb727037.aspx

    For XP, start by running the Network Setup Wizard the on all machines (see warning in section A below).

    Problems sharing files between computers on a network are usually caused by 1) a misconfigured firewall or a firewall neglected (including a dynamic firewall in a virtual private network); or (2) inadvertently run two firewalls such as the firewall of Windows and a third-party firewall. and/or (3) do not have accounts to the same users and passwords on all computers in the workgroup. (4) tries to create actions where the operating system does not.

    A. configure the firewall on all machines to allow traffic to local area network (LAN) as being approved. With the Windows Firewall, it means which allows file sharing / print on the Exceptions tab normally run the XP Network Setup Wizard will take care of this for these machines. The only "witch hunt", it will turn on the XPSP2 Windows Firewall. If you are not running a third-party firewall or you have an antivirus with "Internet Worm Protection" (like Norton 2006/07) which acts as a firewall, you're fine.  With a third-party firewall, I usually set up the allocation of LAN with an IP address range. E.g. would be 192.168.1.0 - 192.168.1.254. Obviously you would substitute your correct subnet. Do not run more than one firewall. DON'T STOP FIREWALLS; CONFIGURE THEM CORRECTLY.

    (B) to facilitate the Organization, put all computers in the same workgroup. This is done from the System applet in Control Panel, the computer name tab.

    C. create the counterpart of the user accounts and passwords on all machines. You do not need to be logged into the same account on all machines and assigned to each user account passwords can be different; accounts/passwords just need to exist and to match on all machines. DO NOT NEGLECT TO CREATE PASSWORDS, EVEN IF ONLY OF SIMPLE. If you want a machine to boot directly to the desktop (a particular user account) for convenience, you can do this. The instructions on this link work for XP and Vista:

    Set up Windows to automatically connect (MVP Ramesh) - http://windowsxp.mvps.org/Autologon.htm

    D. Si one or more of the computers is XP Pro or Media Center, turn off Simple file sharing (Folder Options > view tab).

    E. create share as you wish. XP Home does not share the users directory or the Program Files, but you can share folders inside those directories. A better choice is to simply use the Shared Documents folder. See the first link above for more information on Vista sharing.

    F. you have the job of file sharing (and tested by exchanging a file between machines), if you want to share a printer connected locally to one of your computers, share of this machine. Then go to the printer mftr Web site. and download the latest drivers for the correct system. Install them on the target machines. The printer must be collected during the installation procedure. If this isn't the case, install the drivers and then use the Add Printer Wizard. In some cases, printers must be installed as local printers, but it is outside this response.

  • How to configure the network home wiFi with dlink router

    I need to create a home network using the dlink WiFi router
    a computer with Vista and the second with XP
    can someone tell me what havo to do to configure the router etc etc o give me same informamation on where I can learn to do
    I want just the old pc with xp for the server and the vista one customer but more importantly I need the file on XP to migrate under vista.
    Thank you very muche for your end of the patient cooperation
    in return, I give free cooking classes
    see you soon

    I'm not sure if you are asking how to set up a secure wireless network, if you ask how to share files between your two computers (and there is no "customer" or "server" in a working group, in a field - which is not), or both.

    So I will give you information on doing both.

    Router - configure manually

    Setting up a router is simple enough. Normally, you run the CD that came with the router and follow the instructions. If you're running Vista, maybe the CD that came with the router does not work; I do not know this. But you can set up the router without the CD. Note that if you have Internet cable for the connection you have just set up the router to DHCP (or there may even be a choice of cable to choose). If you have DSL Internet, you select TRP usually and enter the username and password you selected when you initially set the DSL connection. So:

    1. turn off the power to your cable modem.
    2. attach a class (usually supplied with the router) ethernet cable cat5e port Internet/WAN from the router to the ethernet port on the cable modem.
    3. connect the ethernet cable cat5e from the network card in your computer to one of the ports on the router. If you do not have an ethernet cable (because you were using USB), you will need to go to the store and buy a.
    4. turn on the cable modem. After that all the lights are on, turn on the router.

    To configure the router:

    Have a computer connected to the router with an ethernet cable. Examples given are for a Linksys router. See the manual of your router or the router mftr's Web site. for the parameters by default if you don't have a Linksys. Open a browser such as Internet Explorer or Firefox and in the address bar type:

    http://192.168.1.1 [Enter] (it is default IP address of the router, which varies from router to router then check your manual)

    This will bring you to the login screen of the router. The default username is blank and the Linksys default password is "admin" without the quotes. Enter this information. You are now in the configuration of the router utility. Your configuration utility may be slightly different from mine. The first thing to do is to change the default password because * all * known default passwords for different routers.

    Click the Administration link at the top of the page. Enter your new password. MAKE A NOTE SOMEWHERE THAT YOU WILL NOT LOSE. Re-enter the password to confirm it, and then click Save settings at the bottom of the page. The router will reboot and show you the box of connection again. Do not fill in the user name and put it in your new password to enter the configuration utility.

    Now, click on the link wireless at the top of the page. Change the network name (SSID) wireless by default to something, you'll recognize. I suggest that my clients not use their surname as the SSID. For example, you might want to name your network wireless network "CastleAnthrax" or similar. ;-)

    Click on save settings and when you get the prompt that your changes were successful, click the wireless security link which is just beside the Basic Wireless Settings link (where you changed your SSID). Most computers purchased during the last 4 years have the wireless hardware that will support WPA2-Personal (also known as WPA2-PSK). This is the desired encryption level. If your wireless hardware is older, use WPA. Don't use WEP, because who is easily broken within minutes. So go ahead and set the Security Mode WPA2-Personal. Do this and enter a password. For example, you could use the password ' here be dragons, beware you scurvy dogs! The password is what you enter on all computers that are allowed to connect to the wireless network. MAKE A NOTE SOMEWHERE THAT YOU WILL NOT LOSE.

    At this point, your router is set up and if the computer that you use to configure the router will normally connect wireless, disconnect the ethernet cable and wireless of the computer should see your new network. Enter the password that you have created (exactly as you wrote it with all capital letters and punctuation) to join the network and start surfing.

    Networking

    Here are the steps of general network troubleshooting. Just cannot apply to your situation, so just take the bits that are. It may seem daunting, but if you follow the steps in the links and suggestions below calmly and consistently, you will have no difficulty to implement your sharing.

    Excellent, comprehensive, but easy to understand article on sharing files/printer under Vista. Contains information about sharing printers and files, and the folders:

    http://TechNet.Microsoft.com/en-us/library/bb727037.aspx

    For XP, start by running the Network Setup Wizard the on all machines (see warning in section A below).

    Problems sharing files between computers on a network are usually caused by 1) a misconfigured firewall or a firewall neglected (including a dynamic firewall in a virtual private network); or (2) inadvertently run two firewalls such as the firewall of Windows and a third-party firewall. and/or (3) do not have accounts to the same users and passwords on all computers in the workgroup. (4) tries to create actions where the operating system does not.

    A. configure the firewall on all machines to allow traffic to local area network (LAN) as being approved. With the Windows Firewall, it means which allows file sharing / print on the Exceptions tab normally run the XP Network Setup Wizard will take care of this for these machines. The only "witch hunt", it will turn on the XPSP2 Windows Firewall. If you are not running a third-party firewall or you have an antivirus/security with its own firewall component program, then you're fine.  With a third-party firewall, I usually set up the allocation of LAN with an IP address range. E.g. would be 192.168.1.0 - 192.168.1.254. Obviously you would substitute your correct subnet. Refer to the safety of any third party program or the user forums for how to correctly configure its firewall. Do not run more than one firewall. DON'T STOP FIREWALLS; CONFIGURE THEM CORRECTLY.

    (B) to facilitate the Organization, put all computers in the same workgroup. This is done from the System applet in Control Panel, the computer name tab.

    C. create the counterpart of the user accounts and passwords on all machines. You do not need to be logged into the same account on all machines and assigned to each user account passwords can be different; accounts/passwords just need to exist and to match on all machines. DO NOT NEGLECT TO CREATE PASSWORDS, EVEN IF ONLY OF SIMPLE. If you want a machine to boot directly to the desktop (a particular user account) for convenience, you can do this:

    XP - configure Windows to login automatically (MVP Ramesh) - http://windowsxp.mvps.org/Autologon.htm

    Vista - Start ORB > Search > type: netplwiz [Enter]
    Click continue (or provide an administrator password) when you are prompted by UAC

    Uncheck "users must enter a user name and password to use this computer". Select a user account to connect automatically by clicking on the account you want to highlight and press OK. Enter the password for this user account (when it exists) when you are prompted. Leave blank if there is no password (null).

    D. Si one or more of the computers is XP Pro or Media Center, turn off Simple file sharing (Folder Options > view tab).

    E. create share as you wish. XP Home does not share the users directory or the Program Files, but you can share folders inside those directories. A better choice is to simply use the Shared Documents folder. See the first link above for more information on Vista sharing.

    F. you have the job of file sharing (and tested by exchanging a file between machines), if you want to share a printer connected locally to one of your computers, share of this machine. Then go to the printer mftr Web site. and download the latest drivers for the correct system. Install them on the target machines. The printer must be collected during the installation procedure. If this isn't the case, install the drivers and then use the Add Printer Wizard. In some cases, printers must be installed as local printers, but it is outside this response.
    MS - MVP - Elephant Boy computers - don't panic!

  • Network for access to the external interface inside

    Hey,.

    I have an ASA5520 7.2 (1) I have a few probs with - which is something I struggle with that.

    I'm trying to hit a website of a host on the inside network that is actually hosted internally, but decides the static NAT would focus on the external interface of the firewall.

    Now I can see the TCP built, translation occurring at a port on the external interface, this port high dialogue to one of the static electricity would be addresses on the external interface, then that's all. There are no more entries in my journal in regards to the connection and I get not syn on the internal web server is so the connection is not back in.

    IP address outside 222.x.x.9 255.255.255.248

    IP address inside 192.168.87.1 255.255.255.0

    Static NAT to Web servers: -.

    public static 222.x.x.10 (Interior, exterior) 192.168.87.5

    access lists access... :-

    list of allowed inbound tcp extended access any host 192.168.87.5 eq http

    Access-group interface incoming outside in

    Everything works fine when creating a global internet address - just not when address from inside and dynamic PAT is performed to the original address.

    Here's a capture session by using the following access to capture list inside and outside interfaces simultaneously

    permit for line of web access-list 1 scope ip host 222.222.222.10 all

    web access-list extended 2 line ip allow any host 222.222.222.10

    on the INSIDE interface (nothing is connected to the outside) (ip addresses have been replaced by nonsense) - but address 222 is would take into account the interface static and the other is on the internal network.

    316: 19:14:02.900206 192.168.87.10.2275 > 222.222.222.10.80: S 2029971541:2029971541 (0) win 64512

    317: 19:14:05.973185 192.168.87.10.2275 > 222.222.222.10.80: S 2029971541:2029971541 (0) win 64512

    192.168.87.10 is my client is trying to connect

    Someone of any witch hunt, which is stop this function work?

    All networks are directly attached and there is no route summary ancestral anywhere.

    I hope you guys can help!

    Concerning

    Paul.

    To my knowledge the ASA supports only hairpining on a VPN tunnel. The security apparatus does not allow traffic that is sent to an interface to go back in the direction of what she received.

  • Second laptop unable to connect; When trying to connect wirelessly, says connection is successful, but the Public unidentified network, no Internet.

    Hi all.

    I'm really sorry to post this question, I must have read 100 other threads on this topic, but none of the solutions seem to work for me.

    I have a home set wireless network in place, which may not have a lot of problems with it that I have a laptop W7 which has a perfect wireless connection, and also our TV connect when you want, as do our phones and Xbox.

    We bought a second hand Acer aspire laptop for our daughter. It is running Vista Edition family Basic. Even if she had the factory reset done on this, because we can connect to the router with an ethernet cable and it works very well, we managed to ensure that all updates of Windows etc are all complete.

    When trying to connect wirelessly, it says connection successful, but it is to a Public unidentified network, and there is no Internet. Also, even if it says Local access, we cannot connect to the router settings page is.

    I have uninstalled and reinstalled the built-in wireless adapter and updated the driver to do this, he says that he is as up-to-date as possible.

    I checked that DHCP is enabled, we tried dynamic and static IP addresses, we have disabled and re ipv6 enabled, we used the command prompt to reset winsock and stack ip, I looked into msconfig services for service # Id_String1.6844f930_1628_4223_b5cc_5bb94b879762 # Apple off but it isn't here.

    I have a real dislike for Norton / products McAfee and there is none of these on the laptop. We will install Comodo Internet Security, Eusing Registry Cleaner, Spybot S & D and Spyware Blaster as soon as the wireless is configured and that the Windows Firewall is disabled.

    We also have many turns of the spin off the coast and laptops, etc. and deactivation and activation of the adapter.

    It seems that all the usual solutions for the lack of connection are not the culprits this time.

    IPconfig for W7 laptop that works well is:

    Microsoft Windows [Version 6.1.7601]
    Copyright (c) 2009 Microsoft Corporation. All rights reserved.

    C:\Users\Adrian>ipconfig/all

    Windows IP configuration

    Name of the host...: Adrian-laptop
    Primary Dns suffix...:
    Node... type: hybrid
    Active... IP routing: No.
    Active... proxy WINS: No.

    Wireless Network Connection 2 wireless LAN adapter:

    State of the media...: Media disconnected
    The connection-specific DNS suffix. :
    ... Description: Microsoft Virtual WiFi Miniport adapt
    Physical address.... : 78-E4-00-D1-5F-6A
    DHCP active...: Yes
    Autoconfiguration enabled...: Yes

    Wireless network connection Wireless LAN adapter:

    The connection-specific DNS suffix. :
    ... Description: Broadcom 4313 802.11b/g/n
    Physical address.... : 78-E4-00-D1-5F-6A
    DHCP active...: Yes
    Autoconfiguration enabled...: Yes
    Address IPv6 local link...: fe80::30fd:c01f:ab28:fbf9% 13 (Preferred)
    IPv4 address: 192.168.1.3 (Preferred)
    ... Subnet mask: 255.255.255.0.
    Lease obtained...: 13 August 2012 09:16:54
    End of the lease...: August 14, 2012 09:56:23
    ... Default gateway. : 192.168.1.1.
    DHCP server...: 192.168.1.1.
    DHCPv6 IOOKING...: 360244224
    DHCPv6 DUID customer...: 00-01-00-01-13-B2-5C-FD-90-FB-A6-A5-8F-73

    DNS servers...: 192.168.1.1.
    192.168.1.1
    NetBIOS over TCP/IP...: enabled

    Tunnel adapter isatap. {09285A7E-7837-4D7B-994D-C70130D43958}:

    State of the media...: Media disconnected
    The connection-specific DNS suffix. :
    ... Description: Microsoft ISATAP adapter
    Physical address.... : 00-00-00-00-00-00-00-E0
    DHCP active...: No.
    Autoconfiguration enabled...: Yes

    Card adapt 6TO4 tunnel:

    State of the media...: Media disconnected
    The connection-specific DNS suffix. :
    ... Description: Microsoft 6to4 card
    Physical address.... : 00-00-00-00-00-00-00-E0
    DHCP active...: No.
    Autoconfiguration enabled...: Yes

    Card tunnel Local Area Connection * 15:

    The connection-specific DNS suffix. :
    ... Description: Teredo Tunneling Pseudo-Interface
    Physical address.... : 00-00-00-00-00-00-00-E0
    DHCP active...: No.
    Autoconfiguration enabled...: Yes
    IPv6 address: 2001:0:5ef5:73 b 8: 8ed:720:a3fa:1e53 (Prefer
    Red)
    Address IPv6 local link...: fe80::8ed:720:a3fa:1e53% 24 (Preferred)
    ... Default gateway. : ::
    NetBIOS over TCP/IP...: disabled

    Reusable Microsoft 6To4 tunnel map:

    State of the media...: Media disconnected
    The connection-specific DNS suffix. :
    ... Description: Microsoft 6to4 adapt #2
    Physical address.... : 00-00-00-00-00-00-00-E0
    DHCP active...: No.
    Autoconfiguration enabled...: Yes

    Card tunnel Local Area Connection * 11:

    State of the media...: Media disconnected
    The connection-specific DNS suffix. :
    ... Description: Microsoft 6to4 adapt #3
    Physical address.... : 00-00-00-00-00-00-00-E0
    DHCP active...: No.
    Autoconfiguration enabled...: Yes

    IPconfig for the Vista laptop that works wired but not when it's wireless is:

    Microsoft Windows [Version 6.0.6000]
    Copyright (c) 2006 Microsoft Corporation. All rights reserved.

    C:\Users\Adin>ipconfig/all

    Windows IP configuration

    Name of the host...: Georges-PC
    Primary Dns suffix...:
    Node... type: hybrid
    Active... IP routing: No.
    Active... proxy WINS: No.

    Wireless network connection Wireless LAN adapter:

    The connection-specific DNS suffix. :
    ... Description: Atheros AR5007EG Wireless Network adapt

    Physical address.... : 00-1D-D9-1B-71-69
    DHCP active...: Yes
    Autoconfiguration enabled...: Yes
    Address IPv6 local link...: fe80::78c1:cedd:291c:e44b % 11 (Preferred)
    IPv4 address: 192.168.1.2 (Preferred)
    ... Subnet mask: 255.255.255.0.
    Lease obtained...: August 13, 2012 11:28:16
    End of the lease...: August 14, 2012 11:28:16
    ... Default gateway. : 192.168.1.1.
    DHCP server...: 192.168.1.1.
    DHCPv6 IOOKING...: 151002585
    DNS servers...: 192.168.1.1.
    192.168.1.1
    NetBIOS over TCP/IP...: enabled

    Ethernet connection to the Local network card:

    State of the media...: Media disconnected
    The connection-specific DNS suffix. :
    ... Description: Broadcom NetLink (TM) fast Ethernet
    Physical address.... : 00-1B-38-5C-28-24
    DHCP active...: Yes
    Autoconfiguration enabled...: Yes

    Card tunnel Local Area Connection * 6:

    The connection-specific DNS suffix. :
    ... Description: isatap. {E409704E-A039 - 41A 8 - BEB9 - 614B6A018}
    493}
    Physical address.... : 00-00-00-00-00-00-00-E0
    DHCP active...: No.
    Autoconfiguration enabled...: Yes
    Address IPv6 local link...: fe80::5efe:192.168.1.2%12(Preferred)
    ... Default gateway. :
    DNS servers...: 192.168.1.1.
    192.168.1.1
    NetBIOS over TCP/IP...: disabled

    Card tunnel Local Area Connection * 7:

    The connection-specific DNS suffix. :
    ... Description: isatap. {CC1DD067-8D6C-4BDE-BCC8 - 13921 941
    532}
    Physical address.... : 00-00-00-00-00-00-00-E0
    DHCP active...: No.
    Autoconfiguration enabled...: Yes
    ... Default gateway. :
    NetBIOS over TCP/IP...: disabled

    Card tunnel Local Area Connection * 9:

    State of the media...: Media disconnected
    The connection-specific DNS suffix. :
    ... Description: Teredo Tunneling Pseudo-Interface
    Physical address.... : 02-00-54-55-4E-01
    DHCP active...: No.
    Autoconfiguration enabled...: Yes

    Any help or advice will be most appreciated thanks

    Norton or McAfee pre-mstalled of recovery of the manufacturer media?

    If so, did you uninstall it AND run the tool to remove the appropriate product manufacturer?

    Download the Norton removal by https://www-secure.symantec.com/norton-support/jsp/help-solutions.jsp?lg=english&ct=united+states&docid=20080710133834EN&product=home&version=1&pvid=f-home

    Close all other programs, and then run the tool. When it is complete, reboot the machine if she wants it or not.

    Download the removal of McAfee Development tool from:

    http://download.McAfee.com/Products/Licensed/cust_support_patches/MCPR.exe

    Click on save and save the file to a folder on your computer.

    Navigate to the folder where you saved the file.

    Right-click MCPR.exe and select "Run as Administrator" to run the removal tool.

    When you're finished, restart.

  • Does not work from inside the DMZ after configuring the ACL.

    Hello

    According to the concept of ASA, trafuc of the Interior (100 s) DMZ (50 Sec) is allowed by default. When I try to write an acl (host to host block) on the Interface inside, no other traffic runs to and from the Interface on the inside.

    Everything is blocked. Previously no ACL has been mapped to the inside Interface.

    Kindly help me to solve this problem and also provide the document concerning the behavior of the firewall before and after configuring the ACL.

    Poster of the acl that you entered. Remember, there is an explicit deny a whole at the end of the acl. So if you want only to prevent access to a dmz machine, then it must be written correctly. Leave what you want enable dmz, deny the rest of the demilitarized zone, and then leave all the rest.

  • How to configure the VPN LAN to access the internet from the remote network

    I have set up for our project site to another Office VPN. Please join.
    Now I have already configured Site to site vpn between ASA 5510 and 1841 router.

    HQ LAN

    Branch of the LAN
                     10.2.1.0/24 > ASA 5510 1841 > > INTERNET < 1841=""> <> 10.30.3.0/24
    ^
    ^
    ^
    ^
    Call Manager
    No. 2851
    Now access from branch LAN LAN of HQ each other.

    I face problems that are
    (1) in the direction of LAN, they can access HQ LAN & resource, but cannot access the internet. I did not configure NAT on the router PH
    (2) can I access internet BRANCH LAN via HQ LAN INTERNET. Where can I access the Internet of general management of the LAN of the PH router directly while access to the VPN to the local network of HQ?
    (3) in the Site of the Directorate, phone hard cannot work but phone on PC can call to Headquarters. Hard IP phone are same in remote network (172.16.1.0/24 ). What's the problem? How can I configure separately?

    Please give advise me how should I do.

    Hello

    (1) in the direction of LAN, they can access HQ LAN & resource, but cannot access the internet. I did not configure NAT on the router PH

    Answer:

    You must configure the NAT and crossed to the ASA HQ so that the VPN branch router provides LAN and u-Turn, access to Internet of the SAA.  You must first seup NAT for the branch on the SAA router subnet, then you must type the command:

    permit same-security-traffic intra-interface

    Here's a great example for VPN client hairpining.

    http://www.Cisco.com/en/us/products/ps6120/products_configuration_example09186a00805734ae.shtml

    (2) can I access internet BRANCH LAN via HQ LAN INTERNET. Where can I access the Internet of general management of the LAN of the PH router directly while access to the VPN to the local network of HQ?

    Yes, you can

    (3) in the Site of the Directorate, phone hard cannot work but phone on PC can call to Headquarters. Hard IP phone are same in remote network (172.16.1.0/24 ). What's the problem? How can I configure separately?

    You must change your subnet VLANS to be different from the subnet HQ voice phone IP VOice VLAn, it should be fine.

    Kind regards

    Mohamed

  • Configure the network adapter speed / bandwidth management

    Hi all

    In VMware ESX 4, it is possible to configure the speed of vmnic with a speed of diferent? I can do 10, 100, 1000 or full / half-duplex (photos attached) but... is possible to configure the speed of 4 MB, 40 MB or something different?

    For bandwidth management, the best solution is the new Cisco device?

    Thank you very much.

    N ° negotiated between the physical NETWORK adapter and the physical switchport speed can be 10/100/1000. Just like in the physical world...

    But you can do some of the traffic shaping based on your configuration... On a vSwitch standard you can control the evacuation traffic. On a distributed vSwitch, you control evacuation AND penetration.

    / Rubeck

  • Look on OS3 connects to a public wifi network, that has a connection to the Web page.

    in the United Kingdom, we have a public wifi network called "_the cloud", which is free to use, but requires that you register for a free account.

    Once signed, the phone will automatically connect when you are next in the range.

    It seems that since the release of WatchOS3, the Apple Watch will connect now to this public WiFi even with the phone turned off or in flight mode. Suggesting it is connected to a Web page by its self.

    It seems to me that it is only this a public wifi network that does this now, but can't figure out how!

    Great news in any case, I hope that more public wifi networks completely agrees!

    If someone else in the United Kingdom that uses 'cloud _L' public wifi could test this point too, that would be great. I hope that we could get an official comment from Apple?

    https://support.Apple.com/en-GB/HT204562

    Hello

    Thanks for sharing this information.

    Recognition wrote:

    .. I hope that we could get an official comment from Apple?

    It is a community based on the user. If you want to ask Apple about this behavior, contact UK options include:

  • How can I configure the order of networks wifi on my iPhone 6?

    I was browsing the Internet and looking for throughout my general settings but I'm not able to find a way to configure the order of networks wifi on my phone, as I can with my MacBook Air (via Network Preferences > advanced > tab Wi - fi). I had to do a reset to the factory on my router settings and now my iPhone automatically connects to another wifi network in the building which is distant; and, as a result, poor reception. He will also choose my device Chromecast before my own router, so I have to go and manually choose my router every time.

    Is my only option to "forget this network" for the device Chromecast and the other network wifi. Therefore, to move my router plus high in the list (and then add those two later, put further down in the hierarchy list), or y at - it a simple way to just change the order? Thanks for the help.

    Settings > Wi - Fi > select the network to which you want to connect, enter the password.

  • Try to configure the scan to the network folder, name of user and password is incorrect about JO 8600 N911n

    Hello - I have an Officejet 8600 N911n, product number CN577A. My OS is 64-bit, Win8

    My error message is either your user name or password is incorrect, please go back and correct your user name or password.

    No changes were made because this system has a few months other than downloads.

    I tried using the username provided by the scan to network folder setup with the IPL used for the HP forum and support. Also, I deleted the user name provided by the scan to network configuration folder and created a new pw. They have also objected. What user name and pw should be used?

    Hi Wardell1,

    I appreciate that you try to configure the scan to network folder.

    Where do you get this error message?

    Do you get this error message when you try to access SAP of the printer?

    You get this message on the printer?

Maybe you are looking for